SUPER SLIM FAN
WITH NIGHT MODE
User Guide
FA7550
SM8650 featured
Contents
Sunbeam’s Safety Precautions 1
Safety Precautions For Your Tower Fan 2
Locating Your Tower Fan 3
Features Of Your Sunbeam Tower Fan 4
Using Your Tower Fan 8
Troubleshooting Guide 12
Care and Cleaning 12
Contents
Sunbeam’s Safety Precautions 1
Safety Precautions For Your Tower Fan 2
Assembling Your Tower Fan 3
Features Of Your Sunbeam Tower Fan 5
Using Your Tower Fan 6
Locating Your Tower Fan 10
Troubleshooting Guide 11
Care and Cleaning 11
Important instructions – retain for
future use.
Sunbeam’s Safety Precautions
Sunbeam is very safety conscious when
designing and manufacturing consumer products,
but it is essential that the product user also
exercise care when using an electrical appliance.
Listed below are important precautions for the
safe use of an electrical appliance.
• Read carefully and save all the instructions
provided with an appliance.
• Always turn the power off at the power outlet
before you insert or remove a plug. Remove
by grasping the plug - do not pull on the cord.
• Turn the power off and remove the plug
when the appliance is not in use and before
cleaning.
• Do not use your appliance with an extension
cord unless this cord has been checked
and tested by a qualified technician or
service person.
• Always use your appliance from a power
outlet of the voltage (A.C. only) marked
on the appliance.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
• Children should be supervised to ensure that
they do not play with the appliance.
• The temperature of accessible surfaces may be
high when the appliance is operating.
• Never leave an appliance unattended while
in use.
• Do not use an appliance for any purpose
other than its intended use.
• Do not place an appliance on or near a hot gas
flame, electric element or on a heated oven.
• Do not place on top of any other appliance.
• Do not let the power cord of an appliance hang
over the edge of a table or bench top or touch
any hot surface.
• Do not operate any electrical appliance with
a damaged cord or after the appliance has
been damaged in any manner. If damage is
suspected, return the appliance to the nearest
Sunbeam Appointed Service Centre
for examination, repair or adjustment.
• For additional protection, Sunbeam
recommend the use of a residual current
device (RCD) with a tripping current not
exceeding 30mA in the electrical circuit
supplying power to your appliances.
• Do not immerse the appliance in water
or any other liquid unless recommended.
• Appliances are not intended to be operated
by means of an external timer or separate
remote control system.
• This appliance is intended to be used in
household and similar applications such
as: staff kitchen areas in shops, offices and
other working environments; farm houses; by
clients in hotels, motels and other residential
type environments; bed and breakfast type
environments.
If you have any concerns regarding the performance and use of your appliance,
please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.
Ensure the above safety precautions are understood.
1
Safety Precautions For
Your Tower Fan
• Do not use outdoors.
• Do not run the cord of the fan under
carpeting. Do not cover the cord with throw
rugs, runners or other floor coverings.
Arrange the cord away from traffic areas so
that it will not be tripped over.
• Do not use this fan in the immediate
surrounds of a bath, shower, laundry area
or swimming pool.
• Be sure the fan is placed on a dry, even
surface. Do not use on any soft surfaces,
such as beds, where opening may become
blocked.
• Keep your fan away from heat sources,
corrosive gases and avoid
• This fan is only to be used with the base
fitted and in good condition.
• Disconnect the power plug before
dismantling, assembling or before cleaning.
• Always unplug the fan when not in use for
any long period of time.
• The fan must not be used if the guards are
damaged in any way.
direct sunlight.
• Do not insert or allow foreign objects to
enter any ventilation or exhaust openings
as this may cause electric shock or fire,
or damage to the fan.
• Never insert fingers or any other objects
through the guards whenever the power
plug is connected, especially while
running.
• Avoid touching moving parts of the fan.
• Do not attempt to move your fan whilst it is
operating. If your fan needs to be moved,
please ensure that it is turned off and you
use the carry handle on top of the tower.
• When disposing of the fan at the end of its
useful life, follow local regulations.
• Do not coil the power cord too tightly
around the motor housing, as this may
damage the cord.
2
Assembling Your Tower Fan
Join the two halves of the base together
Feed the cord between the two halves of the
1.
base.
Clip the two halves of the base together,
2.
ensuring the cord remains within the channel
f
ormed when the two halves come together.
See figure 1.
Remote Control
The remote control requires a CR2025 battery.
There is a slot to on the back of the unit to
store the remote control when it is not in use.
See figure 2.
CR2032
Figure 1 Figure 2
3
Assembling Your Tower Fan continued
Connecting the tower onto the base
1.Position the base onto the lower part of the
fan. See figure 3. Line up the pin on the
base with the hole in the fan as shown.
2.Fix the base to the fan with the four screws
provided.
3.Secure the power cord as shown.
Figure 3
4
Features of your Sunbeam
Tower Fan
Remote control storage
When not in use, store your remote control in
the handy storage compartment on the rear of
the fan body.
Carry handle
Convenient carry handle allows you to easily
carry your fan from room to room.
Control panel
The control panel shows which functions
have been selected on your tower fan.
5
Selecting a fan speed setting
Your Sunbeam tower fan has 3 speed settings
as follows:
low speed “1” light illuminates
medium speed “2” light illuminates
high speed “3” light illuminates
To select a fan speed, simply press the fan
speed button on the tower or the remote.
Each press of the button will increase the
fan speed and then return back to the lowest
speed again.
•
•
•
Switching the fan on
1.Place the fan on a flat level surface.
2.Insert the plug into a 230/240V power
outlet and turn the power on.
3.To switch on the fan, press the fan
speed button (1, 2 or 3). If you are using
the remote control, the power button needs
to be pressed first.
Switching the fan off
1.To switch the fan off, keep pressing the fan
speed button until it cycles through the fan
speeds and returns to Off.
2.If you will not be using the fan for a length
of time, it is advisable to turn the power off
at the wall socket and unplug the power
cord.
Using Your Tower Fan
Using the oscillation function
The 70 degree oscillation function can be
used on any setting.
Turn the unit on and select any
fan speed.
Press the button on the tower or the
remote. The fan will begin to oscillate from
side to side.
To stop the fan from oscillating, simply
press the button once again.
1.
2.
Using the auto off timer
The auto off timer automatically switches the
fan off after a preset number of hours.
To activate this feature, simply press the auto
off button on the tower or on the remote
control unit.
Press the auto off button once to switch
the fan off after 1 hour. The light on the
tower corresponding to the
position will
illuminate.
Press the auto off button again to have the
fan switch after 2 hours. The light on the
tower corresponding to the
position will
illuminate.
Similarly, pressing the auto off button a 3rd
or 4th time will set the fan to switch after 4
or 8 hours respectively. The corresponding
light on the tower
or will illuminate
accordingly.
To cancel the setting, keep pressing the auto
off timer button until it cycles past 8 hours
and returns to its normal setting. The auto
off timer will be deactivated, the timing light
will be off, and the fan will remain on until it
is switched off manually.
1.
2.
3.
Using Your Tower Fan continued
Using Your Tower Fan
Top panel
Remote control
Adjust the fan setting, timer and oscillation, or activate the night mode from anywhere in the
room using the remote control.
Power button
Fan speed button
Choose from 3 speed settings,
low medium or high.
Oscillation
Your tower fan oscillates 70°,
distributing cool air throughout
the room.
Auto Off button
The auto off timer allows you
to set your tower fan to turn off
after 1, 2, 4 or 8 hours.
Night mode
Turns off all bright lights on
the control panel, leaving only
a dim Night Mode light.
This keeps the room dark when
being used at night, ideal for
when sleeping.
Sleep Breeze mode
In sleep breeze mode
the airflow decreases over time
and then turns off automatically.
This is ideal for when sleeping.
6
Using Your Tower Fan
Using Your Tower Fan continued
Switching the fan on
1.Place the fan on a flat level surface.
2.Insert the plug into a 230/240V power
outlet and turn the power on.
3.To switch on the fan, press the fan
speed button (1, 2 or 3). If you are using
the remote control, the power button needs
to be pressed first.
Switching the fan off
1.To switch the fan off, keep pressing the fan
speed button until it cycles through the fan
speeds and returns to Off.
2.If you will not be using the fan for a length
of time, it is advisable to turn the power off
at the wall socket and unplug the power
cord.
Selecting a fan speed setting
Your Sunbeam tower fan has 3 speed settings
as follows:
•
low speed “1” light illuminates
•
medium speed “2” light illuminates
•
high speed “3” light illuminates
To select a fan speed, simply press the fan
speed button on the tower or the remote.
Each press of the button will increase the
fan speed and then return back to the lowest
speed again.
Using the auto off timer
The auto off timer automatically switches the
fan off after a preset number of hours.
To activate this feature, simply press the auto
off button on the tower or on the remote
control unit.
Press the auto off button once to switch
1.
the fan off after 1 hour. The light on the
tower corresponding to the
illuminate.
2.
Press the auto off button again to have the
fan switch after 2 hours. The light on the
tower corresponding to the
illuminate.
Similarly, pressing the auto off button a 3rd
3.
or 4th time will set the fan to switch after 4
or 8 hours respectively. The corresponding
light on the tower
accordingly.
To cancel the setting, keep pressing the auto
off timer button until it cycles past 8 hours
and returns to its normal setting. The auto
off timer will be deactivated, the timing light
will be off, and the fan will remain on until it
is switched off manually.
Using the oscillation function
The 70 degree oscillation function can be
used on any setting.
1.
Turn the unit on and select any
2.
Press the button on the tower or the
remote. The fan will begin to oscillate from
side to side.
To stop the fan from oscillating, simply
press the button once again.
or will illuminate
position will
position will
fan speed.
7
Using Your Tower Fan continued
Sleep Breeze mode Night mode
The sleep breeze mode automatically cycles
your fan through a fixed pattern of decreasing
speeds, and will then turn off automatically.
This is ideal for when sleeping. Set the fan
speed, and then press the breeze sleep mode
until the breeze icon is lit.
High - Turns off after 8 hours
(2hr high => 3hr medium =>
3hr low => off)
Med - Turns off after 6 hours
(3hr medium => 3hr low => off)
Low - Turns off after 3hours
(3hr low => off)
You can also set the timer button if you would
like the fan to turn off sooner than the above
automatic settings. Eg if you want your fan on
the High speed setting but want it to turn off
sooner than the automatic 8 hour setting, you
can change the timer to 1, 2 or 4 hours.
The night mode function can be used on any
setting.
When activated, all bright lights on the fan
control panel turn off, leaving a dim red
power light which keeps the room dark.
To use Night blackout mode:
1. Choose a fan speed.
2. Press the night mode button
tower or on the remote control unit.
3. All lights will turn off on the fan and a dim
light will display.
4. To cancel the setting, press the night mode
button
to day mode and the lights on the control
panel will illuminate.
To cancel the night mode function, just press
any button and the unit will respond to the
selected change.
on the
again. This will return the fan
8
Using Your Tower Fan continued
Using the remote control
1.Remove the remote control from the
compartment at the rear of the tower as
shown.
2.Point the remote towards the control panel
on the front of the tower to operate.
3.To switch your fan on or off, press the on/
off button .
4.To select a fan speed, press the fan speed
button until the desired fan speed is
chosen.
5.To select oscillation, press the oscillate
button . Press the button again to stop
oscillation.
6.To select sleep breeze mode , press the
sleep breeze button.
7.To select auto off timer , press the timer
button to select 1, 2, 4 or 8 hours
8.To select night mode, press the night mode
button and all bright lights will turn off
leaving a dim night mode light.
Changing the batteries
Slide the rear cover off the remote control
1.
unit.
Replace the spent batteries with fresh
2.
CR2025 battery.
Replace the rear cover.
3.
9
Locating Your Tower Fan
1. Always locate your fan on a level surface.
2. Your tower fan should be located in a dry,
cool, well ventilated location. Keep your
fan away from heat sources, corrosive gases
and avoid direct sunlight.
3. Do not attempt to move your tower fan
whilst it is operating. If your fan needs to
be moved, please ensure that it is turned
off and you use the carry handle at the rear
of the fan.
10
Troubleshooting
Problem Possible Cause What To Do
Tower fan
does not turn on
Remote control
does not work
Control panel lights
do not work
Air cannot enter the fan through
the intake grill.
Fan is not receiving power.
Fan isn’t receiving the signal
from the remote control.
Check that the batteries
are not worn.
Check the fan is not in
Night mode.
Care and Cleaning
Remove any obstructions
from around the fan.
Ensure the electrical outlet
or circuit breaker is working.
Ensure the remote control
is pointed towards the front
of the fan.
Replace if necessary,
see page 11.
Press the Night mode button,
see page 10.
Ensure that your fan is switched off and
disconnected from the power outlet before
cleaning.
• Carefully wipe your fan using a clean cloth.
Do not use abrasive cleaners or brushes to
clean the appliance as these may scratch
the surface.
• Take care that excessive dust does not
build up in the air-intake and air-outlet
grill, and clean it occasionally using a dry
brush or vacuum cleaner.
• Store the fan in a cool dry place when not
in use, in its original carton if possible.
11
Notes
Year
2 year
2 years
Australia
www.sunbeam.com.au
1300 881 861
Units 5 & 6,
13 Lord Street,
Botany NSW 2019
Australia
New Zealand
www.sunbeam.co.nz
0800 786 232
Level 6, Building 5,
Central Park,
660-670 Great South Road,
Greenlane, Auckland
New Zealand
Need help with your appliance?
Contact our customer service team
or visit our website for information
and tips on getting the most from
your appliance.
Australia | visit www.sunbeam.com.au
phone 1300 881 861
mail Units 5 & 6, 13 Lord Street,
Botany NSW 2019 Australia.
New Zealand | visit www.sunbeam.co.nz
phone 0800 786 232
mail Level 6, Building 5,
Central Park,
660–670 Great South Road,
Greenlane, Auckland.
Sunbeam Corporation Limited | ABN 45 000 006 771
Sunbeam Corporation is a division of GUD Holdings Limited.
Sunbeam is a registered trademark.
Made in China to Sunbeam’s specification.
Due to minor changes in design or otherwise,
the product you buy may differ slightly from the one shown here.
Approved by the appropriate electrical regulatory authorities.
©Copyright Sunbeam 2015.
08/15
Loading...