Sunbeam Tower Fan
with Night Mode
Instruction Booklet
FA7250 90cm Remote Controlled Tower Fan
Please read these instructions carefully
and retain for future reference.
SM8650 featured
Contents
Sunbeam’s Safety Precautions 1
Safety Precautions For Your Tower Fan 2
Locating Your Tower Fan 3
Features Of Your Sunbeam Tower Fan 4
Using Your Tower Fan 8
Troubleshooting Guide 12
Care and Cleaning 12
Important instructions – retain for
future use.
Sunbeam’s Safety Precautions
Sunbeam is very safety conscious when
designing and manufacturing consumer products,
but it is essential that the product user also
exercise care when using an electrical appliance.
Listed below are important precautions for the
safe use of an electrical appliance.
• Read carefully and save all the instructions
provided with an appliance.
• Always turn the power off at the power outlet
before you insert or remove a plug. Remove
by grasping the plug - do not pull on the cord.
• Turn the power off and remove the plug
when the appliance is not in use and before
cleaning.
• Do not use your appliance with an extension
cord unless this cord has been checked
and tested by a qualified technician or
service person.
• Always use your appliance from a power
outlet of the voltage (A.C. only) marked
on the appliance.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
• Children should be supervised to ensure that
they do not play with the appliance.
• The temperature of accessible surfaces may be
high when the appliance is operating.
• Never leave an appliance unattended while
in use.
• Do not use an appliance for any purpose
other than its intended use.
• Do not place an appliance on or near a hot gas
flame, electric element or on a heated oven.
• Do not place on top of any other appliance.
• Do not let the power cord of an appliance hang
over the edge of a table or bench top or touch
any hot surface.
• Do not operate any electrical appliance with
a damaged cord or after the appliance has
been damaged in any manner. If damage is
suspected, return the appliance to the nearest
Sunbeam Appointed Service Centre
for examination, repair or adjustment.
• For additional protection, Sunbeam
recommend the use of a residual current
device (RCD) with a tripping current not
exceeding 30mA in the electrical circuit
supplying power to your appliances.
• Do not immerse the appliance in water
or any other liquid unless recommended.
• Appliances are not intended to be operated
by means of an external timer or separate
remote control system.
• This appliance is intended to be used in
household and similar applications such
as: staff kitchen areas in shops, offices and
other working environments; farm houses; by
clients in hotels, motels and other residential
type environments; bed and breakfast type
environments.
If you have any concerns regarding the performance and use of your appliance,
please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.
Ensure the above safety precautions are understood.
1
Safety Precautions For
Your Tower Fan
• Do not use outdoors.
• Do not run the cord of the fan under
carpeting. Do not cover the cord with throw
rugs, runners or other floor coverings.
Arrange the cord away from traffic areas so
that it will not be tripped over.
• Do not use this fan in the immediate
surrounds of a bath, shower, laundry area
or swimming pool.
• Be sure the fan is placed on a dry, even
surface. Do not use on any soft surfaces,
such as beds, where opening may become
blocked.
• Keep your fan away from heat sources,
corrosive gases and avoid direct sunlight.
• This fan is only to be used with the base
fitted and in good condition.
• Disconnect the power plug before
dismantling, assembling or before cleaning.
• Always unplug the fan when not in use for
any long period of time.
• The fan must not be used if the guards are
damaged in any way.
• Do not insert or allow foreign objects to
enter any ventilation or exhaust openings
as this may cause electric shock or fire, or
damage to the fan.
• Never insert fingers or any other objects
through the guards whenever the power
plug is connected, especially while
running.
• Avoid touching moving parts of the fan.
• Do not attempt to move your fan whilst it is
operating. If your fan needs to be moved,
please ensure that it is turned off and you
use the carry handle on top of the tower.
• When disposing of the fan at the end of its
useful life, follow local regulations.
• Do not coil the power cord too tightly
around the motor housing, as this may
damage the cord.
2
Locating Your Tower Fan
1. Always locate your fan on a level surface.
2. Your tower fan should be located in a dry,
cool, well ventilated location. Keep your
fan away from heat sources, corrosive gases
and avoid direct sunlight.
3. Do not attempt to move your tower fan
whilst it is operating. If your fan needs to
be moved, please ensure that it is turned
off and you use the carry handle at the rear
of the fan.
3
Features of your Sunbeam
Tower Fan
Remote control storage
When not in use, store your remote control in
the handy storage compartment on the rear of
the fan body.
Carry handle
Convenient carry handle allows you to easily
carry your fan from room to room.
Power button
Simply press the power button to turn the
unit on.
Control panel
The easy to read control panel allows you
to quickly see what functions have been
selected on your tower fan.
Night mode
Turns off all bright lights on the control
panel, leaving a dim red power light to keep
the room dark at night whilst the fan is
operating.
4
Remote control
Adjust the fan setting, auto off, oscillation
or activate night mode from anywhere in the
room using the full function remote control.
Auto Off button
The auto off timer allows
you to set your tower fan to
turn off after either 1, 2, 4
or 8 hours.
Night mode
Turns off all bright lights on the control
panel, leaving a dim red power light
while the fan is operating. This keeps
the room dark when being used at
night, ideal for when sleeping.
Fan speed button
Choose from 3 speed
settings, low medium
or high.
Oscillation
Your tower fan oscillates 70°,
distributing cool air throughout
the room.
55
Assembling Your Tower Fan
Remove the screws from beneath the tower
Using a phillips head screwdriver, remove the
1.
4 screws from underneath the tower.
Put the screws aside. You will need them to
2.
secure the base.
Join the two halves of the base together
Feed the cord between the two halves of the
1.
base.
Clip the two halves of the base together,
2.
ensuring the cord remains within the channel
formed when the two halves come together.
6
Assembling Your Tower Fan continued
Lower the tower onto the base
Align the tower and the base as shown.
1.
Push the tower down onto the base until it is
2.
firmly held into position.
Screw the tower to the base
Use the 4 screws you put aside earlier to
1.
secure the tower to the base.
Clip the power cord into the semi circular
2.
slot at the edge of the base. Ensure that the
cord fits neatly into the channel.
Stand the fan upright. It is now ready for
3.
use.
7
Using Your Tower Fan
Switching the fan on
Place the fan on a flat level surface.
1.
Insert the plug into a 230/240V power outlet
2.
and turn the power on.
Press the power button
3.
Press the fan speed button
4.
low, medium or high depending on your
preference.
Switching the fan off
To switch the fan off, simply press the power
•
button
•
While the fan remains plugged in to the
power socket, the fan will remember your last
fan speed, oscillation and mode setting for
the next time you switch the fan on again.
•
If you will not be using the fan for a length of
time, it is advisable to turn the power off at
the wall socket and unplug the power cord.
.
.
to select
Selecting a fan speed setting
Your Sunbeam tower fan has 3 speed settings
as follows:
•
low speed “1” light illuminates
•
medium speed “2” light illuminates
•
high speed “3” light illuminates
To select a fan speed, simply press the fan
speed button
Each press of the button will increase the
fan speed and then return back to the lowest
speed again.
on the tower or the remote.
8
Using Your Tower Fan continued
Using the oscillation function
The 70 degree oscillation function can be
used on any setting.
1.
Turn the unit on and select any
2.
Press the button on the tower or the
remote. The fan will begin to oscillate from
side to side.
To stop the fan from oscillating, simply
press the
button once again.
fan speed.
Using the auto off timer
The auto off timer automatically switches the
fan off after a preset number of hours.
To activate this feature, simply press the auto
off button
control unit.
1.
Press the auto off button once to switch
the fan off after 1 hour. The light on the
tower corresponding to the position will
illuminate.
2.
Press the auto off button again to have the
fan switch after 2 hours. The light on the
tower corresponding to the
illuminate.
Similarly, pressing the auto off button a 3rd
3.
or 4th time will set the fan to switch after 4
or 8 hours respectively. The corresponding
light on the tower
accordingly.
To cancel the setting, keep pressing the auto
off button until it cycles past 8 hours and
returns to its normal setting. The auto off
timer will be deactivated, the timing light will
be off, and the fan will remain on until it is
switched off manually.
on the tower or on the remote
position will
or will illuminate
9
Using Your Tower Fan continued
Night mode
The night mode function can be used on any
setting.
When activated, all bright lights on the fan
control panel turn off, leaving a dim red
power light which keeps the room dark.
To use Sleep mode:
1. Choose a fan speed.
2. Press the night mode button (
tower or on the remote control unit.
3. All green lights will turn off on the fan and
a dim red power light will display.
4. To cancel the setting, press the night mode
button (
to day mode and the lights on the control
panel will illuminate.
) again. This will return the fan
) on the
10
Using Your Tower Fan continued
Using the remote control
Remove the remote control from its compart-
1.
ment at the rear of the tower as shown.
Point the remote towards the control panel
2.
on the front of the tower to operate.
Changing the batteries
Slide the rear cover off the remote control
1.
unit.
Replace the spent batteries with 2 fresh AAA
2.
batteries as shown.
Replace the rear cover.
3.
11
Troubleshooting
Problem Possible Cause What To Do
Tower fan
does not turn on
Remote control
does not work
Control panel lights
do not work
Air cannot enter the fan through
the intake grill.
Fan is not receiving power.
Fan isn’t receiving the signal
from the remote control.
Check that the batteries
are not worn.
Check the fan is not in
Night mode.
Care and Cleaning
Remove any obstructions
from around the fan.
Ensure the electrical outlet
or circuit breaker is working.
Ensure the remote control
is pointed towards the front
of the fan.
Replace if necessary,
see page 11.
Press the Night mode button,
see page 10.
Ensure that your fan is switched off and
disconnected from the power outlet before
cleaning.
• Carefully wipe your fan using a clean cloth.
Do not use abrasive cleaners or brushes to
clean the appliance as these may scratch
the surface.
12
• Take care that excessive dust does not
build up in the air-intake and air-outlet
grill, and clean it occasionally using a dry
brush or vacuum cleaner.
• Store the fan in a cool dry place when not
in use, in its original carton if possible.
2 Year Warranty
This Sunbeam product is covered by a 2 year replacement or repair
warranty, which is in addition to your rights under the Australian Consumer
Law (if your product was purchased in Australia) or New Zealand Consumer
Guarantees Act (if your product was purchased in New Zealand).
Should you experience any difficulties with your
product during the warranty period, please contact
our customer service line for advice on 1300 881 861
in Australia, or 0800 786 232 in New Zealand.
Alternatively, you can send a written claim to
Sunbeam to:
Australia
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia
New Zealand
Level 6, Building 5, Central Park,
660-670 Great South Road,
Greenlane, Auckland
Upon receipt of your claim, Sunbeam will seek to
resolve your difficulties or, if the product is defective,
advise you on how to obtain a replacement or refund.
To assist us in managing warranty claims, we
recommend you register your product as soon as
practicable after purchase by creating a MySunbeam
account on our website and send a copy of your
original receipt to Sunbeam.
In order to make a claim under our warranty, you must
have the original proof of purchase documentation for
the product and present it when requested .
Should your product develop any defect within
2 years of purchase because of faulty materials or
workmanship, we will replace or repair it, at our
discretion, free of charge. A product presented for
repair may be replaced by a refurbished product
of the same type rather than being repaired.
Refurbished parts may be used to repair the product.
Our replacement or repair warranty only applies
where a defect arises as a result of faulty material or
workmanship during the warranty period. Your warranty
does not cover misuse or negligent handling (including
damage caused by failing to use the product in
accordance with this instruction booklet), accidental
damage, or normal wear and tear.
Your warranty does not:
• cover freight or any other costs incurred in making a
claim, consumable items, accessories that by their
nature and limited lifespan require periodic renewal
(such as filters and seals) or any consequential loss
or damage; or
• cover damage caused by:
- power surges, power dips, voltage supply problems,
or use of the product on incorrect voltage;
- servicing or modification of the product other than
by Sunbeam or an authorised Sunbeam service
centre;
- use of the product with other accessories,
attachments, product supplies, parts or devices
that do not conform to Sunbeam specifications; or
- exposure of the product to abnormally corrosive
conditions; or
• extend beyond 3 months if the product is used
in commercial, industrial, educational or rental
applications.
The benefits given to you by our warranty are in addition
to other rights and remedies under law in relation to the
product.
In Australia our goods come with guarantees that cannot
be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure
and for compensation for any other foreseeable loss or
damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
Our goods also come with guarantees that cannot be
excluded under the New Zealand Consumer Guarantees
Act.
If your warranty claim is not accepted, we will inform
you and if requested to do so by you, repair the
product provided you pay the usual charges for such
repair. You will also be responsible for all freight and
other costs.
Should your product require repair or service after the
warranty period, contact your nearest Sunbeam service
centre. For a complete list of Sunbeam’s service
centres, visit our website or call our customer service
line for advice on 1300 881 861 in Australia,
or 0800 786 232 in New Zealand.
Need help with your appliance?
Contact our customer service team or visit
our website for information and tips on
getting the most from your appliance.
In Australia
Visit www.sunbeam.com.au
Or call 1300 881 861
In New Zealand
Visit www.sunbeam.co.nz
Or call 0800 786 232
is a registered trademark.
Made in China.
Due to minor changes in design or otherwise,
the product may differ from the one shown in this leaflet.
© Copyright.
ABN 45 000 006 771
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia
Level 6, Building 5, Central Park
660-670 Great South Road
Greenlane, Auckland
New Zealand
Sunbeam Corporation is a division of GUD Holdings Ltd.
Sunbeam Corporation Limited 2014.
5/14
Loading...