Installation
###
Precautions
• Do not tamper with the four holes on the upper surface of the unit. They are used for tuner adjustments
to be made only by service technicians.
• There must be a distance of at least 15 cm between the cassette slot of the unit and shif levet to insert
cassettes easily. Choose the installation location carefully so the unit will not interfere with driving.
• Choose the mounting locatiion carefully so the unit will not interfere with driving.
• Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight or
hot air from the heater, or where it would be subject to dust, dirt or excessive vibration.
• Use only the supplied mounting hardware for safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 20°.
How to Detach and Attach the Front Panel
Before installing the unit, detach the front panel.
To detach
Press (RELEASE) to detach the front panel then gently pull it out.
To attach
Align parts A and B, and push the front panel in until it clicks.
To detach
###
(RELEASE)
###
### •
### •
### •
###### •
###
###
###
###
###
###
###
###
###
To attach
###
Mounting Example
Installation in the dashboard
TO
P
1
182 mm
53 mm
With the TOP marking up
###
21
Bend these claws for a tight fit,
if necessary.
###
3
With the TOP marking up
4
Dashboard
###
###
A
B
Fire wall
###
TOP
1
First attach 4 to the unit, then insert the unit into 1.
2
3
###
###
###
Mounting the Unit in a Japanese Car
You may not be able to install this unit in some makes of Japanese cars. In such a case, consult your Sony
dealer.
5*
max. size 5 x 8mm
With nippers or similar, cut off the
claws on both side of the unit.
.############
#####
to dashboard/center console
Bracket
###
Existing parts supplied with your car
Bracket
###
###
###
5*
max. size
5 x 8mm
#####
#####
###
###
NISSAN12TOYOTA
5*
max. size 5 x 8mm
#####
to dashboard/center console
###
5*
max. size 5
x 8mm
#####
#####
Bracket
###
Bracket
###
Existing parts supplied with your car
###
Note
To prevent malfunction, install only with the supplied screws 5.
####
.###########
Installing the rotary commander
Notes
• Choose the mounting location carefully so the rotary
commander will not interfere with operating the car.
• Do not install the rotary commander in a place where it may
jeopardize the safety of the (front) passenger in any way.
• When installing the rotary commander, be sure not to
damage any electrical cables etc. on the other side of the
mounting surface.
• Avoid installing the rotary commander where it may be
subject to high temperatures, such as from direct sunlight or
hot air from the heater etc.
###
###
• ###
FM/MW/SW
Example of a mounting location
Choose the exact location for mounting the rotary commander,
1
then clean the mounting surface.
Dirt and oil impair the adhesive strength of the double-sided
adhesive tape.
Mark the position for the supplied screw.
2
Use the screw holes on the mounting hardware 9 to mark the
position.
Remove the steering wheel column cover, and drill 2 mm diameter
3
hole at the marked position.
###
###
###
###
###
###
9
Mark
####
###
Cassette Car
Stereo
Installation/Connections
###
XR-7850
Sony Corporation 1998 Printed in Japan
Parts for Installation and Connections
The numbers in the list are keyed to those in the instructions.
1
T
O
P
4 56
2
###
###
3
7
Warm the mounting surface and the double-sided adhesive tape on the mounting
4
hardware 9 to a temperature of 20°C to 30°C, and attach the mounting hardware to the
mounting surface applying even pressure. Use the supplied screw 8 to set into secure
position.
Attach a piece of heavy duty tape etc. on the other side of the mounting surface to cover the
protruding tips of the screws so they will not interfere with any electrical cables etc. inside the
steering wheel column.
Heavy duty tape etc.
Cut the mounting hardware 9,
If necessary.
After reinstalling the steering wheel column cover, attach the rotary commander to the
mounting hardware by aligning the four holes on the bottom of the rotary commander
5
with the four catches on the mounting hardware and sliding the rotary commander
until it locks into place as illustrated.
Note
If you are mounting the rotary commander on the steering wheel column, make sure that the protruding tips of the
screws on the inner surface of the column do not in any way hinder or interfere with the movement of the rotating
shaft, operative parts of the switches or the electrical cables etc. inside the column.
####
9
8
###
###
###
###
###
###
× 4
8!º
The release key 6 is used for dismounting the unit. See the Operating Instructions manual for details.
Caution
• Cautionary notice for handling the bracket 1.
Handle the bracket carefully to avoid injuring your fingers.
• Remove the protection collar 4 before installing
9
.##########################
#########
########
#########
T
O
P
###
Holes
####
4
Release the catch lock as illustrated.
.############
*I-3-862-342-11*(1)
Loading...