TA-FE230/FE330R/FE530R
SERVICE MANUAL
AEP Model
UK Model
Photo: TA-FE530R (BLACK)
SPECIFICATIONS
INTEGRATED STEREO AMPLIFIER
MICROFILM
|
TABLE OF CONTENTS |
|
1. |
GENERAL |
|
|
Location of Controls ....................................................... |
3 |
2. |
DISASSEMBLY ......................................................... |
4 |
3.DIAGRAMS
3-1. Note for Printed Wiring Boards |
|
|
|
and Schematic Diagrams ................................................ |
7 |
3-2. |
Printed Wiring Board – MAIN Section – ...................... |
9 |
3-3. Schematic Diagram – MAIN Section – .......................... |
11 |
|
3-4. |
Printed Wiring Boards – PANEL Section – .................. |
13 |
3-5. |
Schematic Diagram – PANEL Section – ....................... |
15 |
3-6. |
Printed Wiring Boards – POWER Section – ................. |
17 |
3-7. |
Schematic Diagram – POWER Section – ..................... |
19 |
3-8. IC Pin Function Description ........................................... |
22 |
|
4. |
EXPLODED VIEWS ................................................ |
23 |
5. |
ELECTRICAL PARTS LIST ............................... |
26 |
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED
LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
– 2 –
|
SECTION 1 |
|
GENERAL |
LOCATION OF CONTROLS |
|
• Front View |
• Rear View |
1 2
3 4 5 6 7 8 9 !º !¡ !™ !£
1 I/u button
2 Remote sensor (TA-FE330R/FE530R)
3EON LINK button and indicator (TA-FE530R)
4 PHONES jack
5 SPEAKERS switch
6 BASS dial
7 TREBLE dial
8 BALANCE dial
9 LOUDNESS button
0 INPUT SELECTOR
!¡ SOURCE DIRECT button (TA-FE330R/FE530R)
!™ VOLUME dial
!£ TAPE1 MONITOR switch (TA-FE530R)
This section is extracted from instruction manual.
– 3 –
SECTION 2
DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.
CASE
1 screw (CASE)
1 two screws (CASE)
2 case
1 two screws (CASE)
PANEL ASS’Y
2 connector (CN7) (FE230) |
|
2 connector (CN903) |
|
(FE330R/FE530R) |
1 wire (flat type) (13 core) |
|
(CN811) |
3 two clamps |
|
|
1 wire (flat type) (13 core) |
4 screw (BVTP3 × 8) |
(CN815) |
5 claw
6 panel ass’y |
2 connector (CN812) |
|
(FE530R) |
||
|
||
|
4 screw (BVTP3 × 8) |
4three screws (BVTP3 × 8)
5 claw
– 4 –
MAIN BOARD
1 connector (CN951)
1 connector
(CN952: FE330R/FE530R) CN952A: FE230
4 screw (BVTP3 × 8)
5 MAIN board
3 six screws (BVPT 3 ×8)
(FE330R/FE530R)
FE230
3 six screws (BVPT 3 ×8) (FE230)
2 six screws (BVPT 3 ×8)
– 5 –
SECTION 3
DIAGRAMS
3-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Boards:
•Y: parts extracted from the component side.
•¢ : internal component.
•b: Pattern from the side which enables seeing.
•Indication of diode
D
This marking side is cathode.
Note on Schematic Diagrams:
•All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums.
•All resistors are in Ω and 1/4 W or less unless otherwise specified.
•¢ : internal component.
•2: nonflammable resistor.
•5: fusible resistor.
•C: panel designation.
Note: The components identified by mark ! or dotted line with mark ! are critical for safety.
Replace only with part number specified.
•U : B+ Line.
•V : B– Line.
•Voltages are dc with respect to ground under no-signal conditions.
no mark : TUNER
•Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances.
•Signal path. F : TUNER
E : TAPE1/DAT IN a : REC OUT d : TAPE2/MD IN J : CD
I : PHONO
• Circuit Boards Location
FUSE board
DC-SUP board
AC-SW board (FE230)
POWER SW board (FE330R/FE530R)
H. P board
FUNCTION SW board
AC-RY board (FE330R/FE530R)
AC OUTLET board
(FE330R: AEP/FE530R: AEP)
MAIN board
CONTROL board |
TAPE MONITOR board |
|
(FE530R) |
– 7 – |
– 8 – |
TA-FE230/FE330R/FE530R
3-2. PRINTED WIRING BOARD – MAIN Section – • See page 8 for Circuit Boards Location.
(Page 13) (Page 18) (Page 17) |
(Page 14) |
(Page 13) |
(Page 17)
•Semiconductor Location
Ref. No. |
Location |
D101 |
C-4 |
D301 |
E-6 |
D302 |
E-6 |
D351 |
E-6 |
D352 |
E-6 |
D601 |
C-5 |
D902 |
C-5 |
D903 |
C-5 |
IC101 |
D-3 |
IC102 |
C-1 |
IC301 |
E-7 |
IC601 |
E-3 |
IC901 |
E-5 |
Q101 |
E-5 |
Q102 |
E-5 |
Q103 |
C-4 |
Q104 |
E-4 |
Q151 |
E-5 |
Q301 |
E-6 |
Q351 |
D-6 |
Q901 |
C-5 |
Q902 |
C-5 |
Q903 |
E-4 |
|
|
– 9 – |
– 10 – |
Loading...