Sony SLV-SE610K, SLV-SX710N, SLV-SE710K, SLV-SE710N, SLV-SX710K User Manual

...

3-065-678-11 (1) GB

Video Cassette Recorder

Operating Instructions

PAL

SLV-SE610N/K SLV-SE710N/K SLV-SX710N/K SLV-SE810N/K

WARNING

To prev e nt fire or shock hazard, do no t expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

Mains lead must only be changed at a qualified service shop.

Precautions

Safety

• This unit operates on 220 – 240 V AC, 50 Hz. Check that the unit’s operating voltage is identical with your local power supply.

• If anything falls into the cabinet, unplug the unit and have it checked by qualified personnel before operating it any further.

• The unit is not disconnected from the mains as long as it is connected to the mains, even if the unit itself has been turned off.

• Unplug the unit from the wall outlet if you do not intend to use it for an extended period of time. To disconnect the cord, pull it out by the plug, never by the cord.

Installing

• Allow adequate air circulation to prevent internal heat buildup.

• Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation slots.

• Do not install the unit near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock.

• Do not install the unit in an inclined position. It is designed to be operated in a horizontal position only.

• Keep the unit and cassettes a w ay from eq uipment with strong magnets, such as microwav e o ve ns o r large loudspeakers.

• Do not place heavy objects on the unit.

• If the unit is brought directly from a cold to a warm location, moisture may condense inside the VCR and cause damage to the video head and tape. When you first install the unit, or when you move it from a cold to a warm location, wait for about three hours before operating the unit.

Caution

Te le visi on prog rammes , f il ms, vid eo tapes a nd ot her materials may be copyrighted. Unauthorized recording of such material may be contrary to the provisions of the copyright laws. Also, use of this recorder with cable television transmission may require authorization from the cable television transmitter and/or programme owner.

Compatible colour systems

This VCR is designed to record using the PAL (B/G or D/K) or MESECAM (B/G or D/K) colour system and play back using the PAL (B/G or D/K) or MESECAM (B/G or D/K) colour systems. Recording of video sources based on other colour systems cannot be guaranteed.

HOWVIEW

S Development Corporation. The S is manufactured under license from Gemstar Development Corporation.

is a registered trademark of Gemstar

HOWVIEW

system

WARNING

Table of contents

Getting Started

Index to parts and controls

Step 1 : Unpacking

Step 2 : Setting up the remote commander

Step 3 : Connecting the VCR

Step 4 : Tuning your TV to the VCR

Step 5 : Setting up the VCR with the Auto Set Up function

Step 6 : Setting the clock

Selecting a language

Presetting channels

Changing/disabling programme

positions Setting the Canal Plus deco der

(not available on SLV-SE610N/K)

Basic Operations

Playing a tape

Recording TV programmes

Recording TV programmes using

the Dial Timer

(SLV-SE810N/K only)

Recording TV programmes using

the ShowView system

(not available on SLV-SE610N/K)

Recording TV programmes using

the timer

Additional Operations

Playing/searching at various speeds

Setting the recording duration time

Synchronized Recording

(not available on SLV-SE610N/K)

Checking/changing/cancelling

timer settings Recording stereo and bilingual

programmes Searching using the Smart Search

function Storing, searching and deleting

programme information (Smart Search Plus)

Searching using the index function

Adjusting the picture

Reducing the VCR’s power

consumption Changing menu options

Editing

Connecting to a VCR or stereo

system Basic editing

Audio dubbing

(SLV-SE810N/K only)

Additional Information

Troubleshooting

Specifications

Index

98 Back Cover

Quick Start Guide

Table of contents

Getting Started

Index to parts and controls

Refer to the pages indicated in parentheses ( ) for details.

Front panel

SLV-SE810N/K

(on/standby) switch (19)

A ?/1

Tape compartment

Remote se nsor (11)

(eject) button (44)

D A

Shuttle ring (63)

E F H

G H z

(play) button (44) (63)

JOG button (64)

REC (record) button (46) (65)

(89)

(pause) button (44) (89)

I X

(stop) button (44) (89)

J x K M L m

(fast-forward) button (44) (63) (rewind) button ( 4 4) (63)

DIAL TIMER (50)

PROGRAM +/– buttons (22) (64)

(81) AUDIO DUB button (90)

AUTO SET UP/

RF (Radio Frequency) CHANNEL button (19) (2 2)

SYNCHRO REC (Synchronized

Recording) button (67)

LINE-2 L (left) o R (right)

R t

jacks (covered) (87) (88)

How to open the jack cover

1 Press the bottom of the cover. 2 Hook your finger on the top edge of the

cover and pull it open.

Index to parts and controls

SLV-SE610N/K, SE710N/K, SX710N/K

Getting Started

(on/standby) switch (19)

A ?/1

Tape compartment

Remote se nsor (11)

(eject) button (44)

D A

(play) button (44) (63)

E H

REC (record) button (46) (65)

F z

(89)

(pause) button (44) (89)

G X

(stop) button (44) (89)

H x

* not available on SLV-SE610N/K

I M J m

(fast-forward) button (44) (63) (rewind) button (44) (63)

PROGRAM +/– buttons (22) (64) (81)

AUTO SET UP/

RF (Radio Frequency) CHANNEL button (19) (22)

SYNCHRO REC (Synchronized

Recording) button* (67)

continued

Index to parts and controls

Display window

STEREO NICAM SYNCHRO

Timer indicator (52) (57) (60)

(70)

(67)

(17)

SYNCHRO indicator*

STEREO indicator (70)

NICAM indicator*

(smartlink) indicator*

VIDEO indicator (16) (47)

VPS (Video Programme System)/

PDC (Programme Delivery Control)

indicator* Tape speed indicators (46)

(57)

SPLP OPCVIDEO VPS

PDC EP TV

OPC (Optimum Picture Control)

indicator (82)

TV indicator*

Audio dubbing indicator*

Tracking indicator (81)

Time counter/clock/line/programme

(48)

(90)

position indicator (44) (46) (89) Remaining time indicator (47)

RR (Reality Regenerator) indicator

(81) Tape/recording indicator (46)

*1not available on SLV-SE610N/K

SLV-SE610N, SE710N, SX71 0N, and SE810N only

SLV-SE810N/K only

Index to parts and controls

Rear panel

Getting Started

Mains lead (15) (16)

DECODER/t LINE-2 IN

DECODEUR/t ENTREE LIGNE-

2 connector*

(18) (39) (66) (88)

DECODER/t LINE-3 IN DECODEUR/t ENTREE LIGNE3 connector*

AERIAL IN

(18) (39) (66) (88)

ANTENNE ENTREE connector (15) (16)

*1SLV-SE710N/K and SX710N/K only

SLV-SE810N/K only

not available on SLV-SE610N/K

AERIAL OUT

ANTENNE SORTI E connector (15 ) (16)

E i

LINE-1 (TV) LIGNE-1 (TV) connector (16)

(39)

(audio out) R/D (right) L/G (left)

jacks*

(18)

continued

Index to parts and controls

Remote commander

EJECT button (44)

A Z

123 456 789

WIDE button (

AUDIO MONITOR button (70)

×2 button* (63)

SLOW button* (63)

E y

SP (Standard Play)/LP (Long Play)

for TV

) (13)

button (46)

DISPLAY button (47)

(ten’s digit) button (12) (47)

H -

(volume) +/– buttons (

I 2

for TV

(13)

REC (record) button (46) (65)

J z

MENU button (25) (68)

PAUSE/M button (25) (4 4)

L X

STOP/m button (25) (44)

REW (rewind)/< button (44)

(63)

FF (fast-forward)/, button

(44) (63)

PLAY/OK button (25) (44)

)

Index to parts and controls

* FASTEXT buttons (

SE810N/K only)

for TV

) (SLV-

M [TV]

(11)

[VIDEO]

remote control switch

Getting Started

123 456 789

N ?/1

P a

Q ./>

S t

(on/standby) switch (12) (57)

COUNTER/REMAIN button (47)

(Teletext) button*

(

for TV

TV power on/TV mode select

button*

(

for TV

) (12)

INDEX SEARCH

buttons*

(80)

CLEAR button (44) (56) (68)

TV/VIDEO button (12) (16) (47) Programme number b uttons (12) (4 7) INPUT SELECT button (47) (60)

(89) PROG (program me) +/– b uttons (12 )

(31) (46)

T eletext page access buttons*

c/C

(

) (13)

for TV

TIMER button (55) (59)

SMART SEARCH button (73)

*1FASTEXT buttons (

SE810N/K only)

SLV-SE810N/K only

for TV

) (SLV-

) (13)

Index to parts and controls

Step 1 : Unpacking

Check that you have received the following items with the VCR:

• Remote commander • Aerial cable

• R6 (size AA) batteries

Check your model name

The instructions in this manual are for the 8 models: SLV-SE610N, SE610K, SE710N, SE710K, SX710N, SX710K, SE810N, and SE810K. Check your model number by looking at the rear panel of your VCR. SLV-SE810N is the model used for illustration purposes. Any difference in operation is clearly indicated in the text, for example, “SLV-SE710N only.”

Unpacking

Step 2 : Setting up the remote commander

123 456 789

Inserting the batteries

Insert two R6 (size AA) batteries by matching the + and – on the batteries to the diagram inside the battery compartment.

Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position.

Using the remote commander

You can use this remote commander to operate this VCR and a Sony TV. Buttons on the remote commander marked with a dot (•) can be used to operate your Sony TV. If the TV does not have the symbol near the remote sensor, this remo te commander will not operate the TV.

Remote sensor

Getting Started

To operate Set

the VCR a Sony TV

[TV]

[VIDEO]

and point at the remote sensor at the VCR

[TV]

and point at the remote senso r at the TV

[VIDEO]

[TV]

[VIDEO]

continued

Setting up the remote commander

WIDE

AUDIO MONITOR

FASTEXT buttons

DISPLAY

123 456 789

????/1111

tttt

TV/VIDEO

Programme number buttons

PROG +/–/

c/C

+/–

2222

TV control buttons

To Press

Set the TV to standby mode Select an input source: aerial in or line in Select the TV’s programme positio n Programme number buttons,

Setting up the remote commander

?/1

TV/VIDEO

, PROG +/–

To Press

Adjust the volume of the TV Switch to TV (Teletext off)* Switch to Teletext* Select the sound AUDIO MONITOR Use FASTEXT* FASTEXT buttons Call up the on-screen display

Change the Teletext page* Switch to/from wide mode of a Sony wide TV (For

other manufactures’ wide T V s, see “Controlling other TVs with the remote commander (SLVSE810N/K only)” below.)

Notes

• With normal use, the batteries should last about three to six months.

• If you do not use the remote commander for an extended period of time, remove the batteries to avoid possible damage from battery leakage.

• Do not use a new battery together with an old one.

• Do not use different types of batteries together.

• Some buttons may not work with certain Sony TVs.

* SLV-SE81 0N /K on ly

+/–

(TV)

(Teletext)

DISPLAY

c/C

WIDE

Controlling other TVs with the remote commander (SLV-SE810N/K only)

The remote commander is preprogrammed to co ntrol non-Son y TVs. If yo ur TV is listed in the following table, set the appropriate manufacturer’s code number.

Getting Started

Set

Hold down ?/1, and enter your TV’s code number using the programme

number buttons. Then release ?/1.

[TV]

[VIDEO]

at the top of the remote commander to

[TV]

Now you can use the following TV control buttons to control your TV:

?/1, t

TV/VIDEO, programme number buttons, - (ten’s digit), PROG +/–, 2 +/–, a (TV), / (Teletext), FASTEXT buttons, WIDE*, MENU*,

* These buttons may not work with all TVs.

M/m/</,

*, and OK*.

continued

Setting up the remote commander

Code numbers of controllable TVs

If more than one code number is listed, try entering them one at a time until you find the one that works with your TV.

To switch to wide mode, see the foo t notes b elow this table for the applicable code numbers.

Manufacturer Code number

Sony

01*1, 02 Akai 68 Ferguson 52 Grundig

10*1, 11*

Hitachi 24 JVC 33 Loewe 45 Mivar 09, 70 NEC 66 Nokia

15, 16, 69*

Manufacturer Code number

Panasonic Philips

17*1, 49

06*1, 07*1, 08* Saba 12, 13 Samsung 22, 23 Sanyo 25 Sharp 29 Telefunken 36 Thomson

43*

Toshiba 38

*1Press WIDE to switch the wide picture mode on or off.

Press WIDE, then press 2 +/– to select the wide picture mode you want.

Press WIDE. The menu appears on the TV screen. Then, press M/m/</, to

select the wide picture you want an d press OK.

Tip

• When you set your TV’s code number correctly while the TV is turned on, the TV turns off automatically.

Notes

• If you enter a new code number, the code number previously entered will be erased.

• If the TV uses a different remote control system from the one programmed to work with the VCR, you cannot control your TV with the remote commander.

• When you replace the batteries of the remote c ommander, the code number may change. Set the appropriate code number every time you replace the batteries.

Setting up the remote commander

Step 3 : Connecting the VCR

AERIAL

ANTENNE

ENTREE

OUT

SORTIE

ENTREE

OUT

SORTIE

AERIAL

ANTENNE

If your TV has a Scart (EURO-AV) connector, see page 16.

If your TV does not have a Scart (EURO-AV) connector

AERIAL IN

AERIAL OUT

Mains lead

to mains

Aerial cable (supplie d)

: Signal flow

Getting Started

AERIAL IN

Disconnect the aerial cable from your TV and connect it to AERIAL IN on the rear panel of the VCR.

Connect AERIAL OUT of the VCR and the aerial input of your TV using the supplied aerial cable.

Connect the mains lead to the mains.

Note

• When you connect the VCR and your TV only with an aerial cable, you have to tune your TV to the VCR (see page 19).

continued

Connecting the VCR

If your TV has a Scart (EURO-AV) connector

AERIAL

ANTENNE IN

ENTREE

OUT

SORTIE

ENTREE

OUT

SORTIE

AERIAL

ANTENNE

AERIAL IN

Mains lead

to mains

LINE-1

(TV)

: Signal flow

Scart cable (not supplied)

AERIAL OUT

Aerial cable (supplied)

AERIAL IN

Scart (EURO-AV)

Disconnect the aerial cable from your TV and connect it to AERIAL IN on the rear panel of the VCR.

Connect AERIAL OUT of the VCR and the aerial input of your TV using the supplied aerial cable.

Connect LINE-1 (TV) on th e VCR and the Scart (EURO-AV) connector on the TV with the optional Scart cable.

This connection improves picture and sound quality. Whenever you want to watch the VCR picture, press tTV/VIDEO to display the VIDEO indicator in the display win dow.

Connect the mains lead to the mains.

Connecting the VCR

Note

• If the TV is connected to the LINE-1 (TV) connector, setting the RF channel to

OFF is recommended. In the OFF position, only the signal from the aerial is output through the AERI AL OUT connector (see page 21).

About the SMARTLINK features (not available on SLV-SE610N/K)

If the connected TV complies with SMARTLINK, MEGALOGIC* EASYLINK* VIEW LINK*

, Q-Link*3, EURO

, or T-V LINK*5, this VCR automatically runs the SMARTLINK function after you complete the steps on the previous page (the indicator appears in the VCR’s display window when you turn on the TV). You can enjoy the following SMARTLINK features.

• Preset Download

You can download your TV tuner preset data to this VCR and tune the VCR according to that data in Auto Set Up. This greatly simplifies the Auto Set Up procedure. Be careful not to disconnect the cables o r exit the Auto Set Up function during the procedure. See “Setting up the VCR with the Auto Set Up function” on page 22.

• TV Direct Rec

You can easily record what you are watching on the TV. For details, see “Recording what you are watching on the TV (TV Direct Rec) (not available on SLV-SE610N/K)” on page 48.

• One Touch Play

With One Touch Play, you can start playback automatically without turning on the TV. For details, see “Starting playback automatically with one button (One Touch Play) (not available on SLV-SE610N/K)” on page

45.

• One Touch Menu

You can turn on the VCR and TV, set the TV to the video channel, and display the VCR’s on-screen display automatically by pressing MENU on the remote commander.

• One Touch Timer

You can turn on the VCR and TV, set the TV to the video channel, and display the timer recording menu (the TIMER METHOD menu, the TIMER menu, or the SHOWVIEW menu) automatically by pressing TIMER on the remote commander. You can set which timer recording menu is displayed using TIMER OPTIONS in the OPTIONS-2 menu (see page 85).

• Automatic Power Off

You can have the VCR turn off automatically, if the VCR is not used after you turn off the TV.

*1“MEGALOGIC” is a registered trademark of Grundig Corporat i on.

“EASYLINK” is a trademark of Philips Corporation.

“Q-Link” is a tra demark of Panasonic Corpor ation.

“EURO VIEW LINK” is a trademark of Toshiba Corpora t ion.

“T-V LINK” is a trademark of JVC Corporation.

Getting Started

Note

• Not all TVs respond to the functions above.

continued

Connecting the VCR

Additional connections

To a stereo system (not available on SLV-SE610N/K)

You ca n improve sound quality by connecting a stereo system to the R/D L/G jacks as shown on the right.

To a satellite or digital tuner with Line Through (not available on SLV-SE610N/K)

Using the Line Through function, you can watch programmes from a satellite or digital tuner connected to this VCR on the TV even when the VCR is turned off. When you turn on the satellite or digital tuner, this VCR automatically sends the signal from the satellite or digital tuner to the TV without turning itself on.

Audio cable (not supplied)

: Signal flow

DECODER/

LINE-3 IN*

or DECODER/

LINE-2 IN*

: Signal flow

R/D L/G

Scart cable (not supplied)

LINE IN

LINE OUT

Connecting the VCR

Connect the satellite or digital tuner to the DECODER/LINE-3 IN*1 (or

DECODER/LINE-2 IN* Set DECODER/LINE3*1 (or DECODER/LINE2*2) to LINE3*1 (or

LINE2* Set POWER SAVE to OFF or PARTIAL*

Turn off the VCR.

) in the OPTIONS-2 menu.

) connector as shown above.

in the OPTIONS-2 menu.

To watch a programme, turn on the satellite or digital tuner and the TV.

Note

• You cannot watch programmes on the TV while recording unless you are recording a satellite or digital programme.

SLV-SE810N/K only

SLV-SE710N/K and SX710N/K only

not available on SLV-SE610N/K

Step 4 : Tuning your TV to the VCR

If your TV has a Scart (EURO-AV) connector, see page 21.

If your TV does not have a Scart (EURO-AV) connector

Follow the steps below so that your TV will properly receive the video signals from your VCR.

Getting Started

1 2

AUTO

SET UP

RF CHANNEL

????/1111

Press ?/1 (on/standby) to turn on the VCR.

Press RF CHANNEL on the VCR lightly. The factory-preset RF channel appears in the display window. The VCR signal is output through this channel to the TV.

Turn on your TV and select a programme position for the VCR picture.

This programme position will now be referred to as the video channel.

RF CHANNEL

PROGRAM +/–

AUTO

SET UP

RF CHANNEL

Press RF CHANNEL. The TV system appears in the display window.

continued

Tuning your TV to the VCR

SONY VIDEO CASSETTE RECORDER

PROGRAM

Press PROGRAM +/– (repeatedly) to select the appropriate TV system for your area. Select “G” for the B/G TV system, or “K” for the D/K TV system.

Tune the TV to the same channel shown in the VCR display window so that the picture on the right appears clearly on the TV screen.

Refer to your TV manual for TV tuning instructions .

If you select the wrong TV system in step 5, the picture on the right may not appear. Select the appropriate TV system and tune the TV again.

If the picture does not appear clearly, see “To obtain a clear picture from the VCR” below.

AUTO

SET UP

Press RF CHANNEL. You have now tuned your TV to the VCR. Whenever you want to

play a tape, set the TV to the video channel.

RF CHANNEL

To check to see if the TV tuning is correct

Set the TV to the video channel and press PROGRAM +/– on the VCR. If the TV screen changes to a different programme each time you press PROGRAM +/–, the TV tuning is correct.

To obtain a clear picture from the VCR

If the screen does not appear clearly in s tep 6 abo ve, go to step 7 to fi nish this procedure once. Then start again from step 2. After pressing RF CHANNEL in step 2, press PROGRAM +/– while the RF channel is displayed, so that another RF channel appear s. Th en tun e the T V to the new RF channel so that a clear picture appears.

Tuning your TV to the VCR

Note

• If you set the wrong TV system, you may have no sound or sound may be distorted.

If your TV has a Scart (EURO-AV) connector

Getting Started

1 2

AUTO

SET UP

RF CHANNEL

PROGRAM

????/1111

RF CHANNEL

PROGRAM +/–

Press ?/1 (on/standby) to turn on the VCR.

Press RF CHANNEL on the VCR lightly. The factory-preset RF channel appears in the display window. The VCR signal is output through this channel to the TV.

Press PROGRAM +/– to set the RF channel to OFF, and press RF CHANNEL again.

AUTO

SET UP

RF CHANNEL

RF channel set up is complete.

Tuning your TV to the VCR

Step 5 : Setting up the VCR with the Auto

Set Up functi on

Before using the VCR for the first time, set up the VCR using the Auto Set Up function. With this function, you can set the language for the on-screen display, TV channels, guide channels for the ShowView system*, and VCR clock* automatically.

????/1111

AUTO SET UP

PROGRAM +/–

AUTO

Setting up the VCR with the Auto Set Up function

SET UP

RF CHANNEL

PROGRAM

Hold down AUTO SET UP on the VCR for more than three seconds.

The VCR automatically turns on, and the country abbreviation appears in the display window.

Press PROGRAM +/– to select the abbreviation of your country from the table on page 23.

For some countries, there is a selection of languages to choose from. If your country does not appear, select ELSE.

AUTO

SET UP

Press AUTO SET UP lightly. The VCR starts searching for all of the receivable channels and

presets them according to the TV system you selected in “Tuning

RF CHANNEL

your TV to the VCR” on page 19. If you want to chan ge t he ord er of the channels or disable un wanted

programme positions, see “Changing/disabling programme positions” on page 34.

If you use the SMARTLINK connection (not available on SLVSE610N/K), the Preset Download function starts and the indicator flashes in the display window during download.

For SLV-SE710N/K, SX710N/K, and SE810N/K: After the search or download is complete, the current time appears in the display window for any stations that transmit a time signal.

For SLV-SE610N/K: When no more receivable channels can be found, presetting stops and “SET UP” disappears from the display window.

The abbreviations of the countries and la ngua ges are as f ollo ws :

Abbreviation Country Language

CZ Czecho Czech HUN Hungary Hungarian PL Poland Polish SK Slovakia Slovak TR Turkey Turkish RUS Russia Russian ELSE Other countries English

Getting Started

To cancel the Auto Set Up function

Press AUTO SET UP.

Tip

• If you want to change the language for the on-screen display from the one preset in the Auto Set Up function, see page 29.

continued

Setting up the VCR with the Auto Set Up function

Notes

• If you stop the Auto Set Up function during step 3, you must repeat set up from

step 1.

• Whenever you operate the Auto Set Up function, some of the settings

(ShowView*, timer, etc.) will be reset. If this happens, you have to set them again.

* not available on SLV-SE610N/K

Setting up the VCR with the Auto Set Up function

Step 6 : Setting the clock

SET :

SELECT :

MENUEXIT :

SETTINGS

RETURN

TUNER CLOCK LANGUAGE

SET :

SELECT :

MENUEXIT :

CLOCK

OFFAUTO ADJUST CLOCK PROGRAM MANUAL ADJUST

.1 1 . 2001 MON 0: 00

CONFIRM :

SET :

MENUEXIT :

CLOCK

OFFAUTO ADJUST CLOCK PROGRAM MANUAL ADJUST

1 . 1.2001 MON 0 : 00

SELECT :

You must set the time and date on the VCR to use the timer features properly. The Auto Clock Set function (not available on SLV -SE610N/K) works only if a station

in your area is broadcasting a time signal. If the Auto Set Up function did not set the clock correctly for your l o cal area, t r y another station for the Aut o Cl ock Se t fun c ti on.

Setting the clock manually

Getting Started

Before you start

…

• Turn on the VCR and the TV.

• Set the T V to the video channel.

• Refer to “Index to parts and controls” for button locations.

PLAY

Press MENU, then press M/m to highlight SETTINGS a n d press OK.

Press M/m to highlight CLOCK, then press OK.

For SLV-SE610N/K, only the clock setting menu appears. Skip the next step and go to step 4.

PLAY

Press M/m to highlight MANUAL ADJUST, then press OK.

continued

Setting the clock

CONFIRM :

SET :

MENUEXIT :

CLOCK

OFFAUTO ADJUST CLOCK PROGRAM MANUAL ADJUST

8 . 1. 2001 SUN 0 : 00

SELECT :

CONFIRM :

SET :

MENUEXIT :

CLOCK

OFFAUTO ADJUST CLOCK PROGRAM MANUAL ADJUST

8 . 9. 2001 FRI 0 :00

SELECT :

CONFIRM :

SET :

MENUEXIT :

CLOCK

OFFAUTO ADJUST CLOCK PROGRAM MANUAL ADJUST

8 . FRI 8 :0 0

SELECT :

21.20019

MENUEXIT :

CLOCK

OFFAUTO ADJUST CLOCK PROGRAM MANUAL ADJUST

8 . FRI 8 :0 0

SET :

SELECT :

.20019

Press M/m to set the day.

PLAY

Press , to highlight the month and set the month pressing M/m.

Set the year, hour, and minutes in sequence, pressing , to highlig ht the item to be set, and press M/m to select the digits.

The day of the week is set automatically.

Press OK to start the clock.

Press MENU to exit the menu.

Tips

• To chang e the digits while setting, press < to return to the item to be changed, and select the digits by pressing M/m.

• If you want to return to the previous menu, highlight RETURN and press OK.

Setting the clock

Note

• The menu disappears automatically if you don’t pro cee d for more than a few minutes.

Changing the station for the Auto Clock Set function

SET :

SELECT :

MENUEXIT :

SETTINGS

RETURN

TUNER CLOCK LANGUAGE

SET :

SELECT :

MENUEXIT :

CLOCK

1 AAB

AUTO ADJUST CLOCK PROGRAM MANUAL ADJUST

.8 FRI 8 : 00

12 .20019

CONFIRM :

SELECT :

MENUEXIT :

CLOCK

OFF

AUTO ADJUST CLOCK PROGRAM MANUAL ADJUST

FRI 8 : 00

8.ON21.20019

SET :

SELECT :

MENUEXIT :

CLOCK

1 AAB

AUTO ADJUST CLOCK PROGRAM MANUAL ADJUST

.8 FRI 8 : 00

12 .20019

(not available on SLV-SE610N/K)

Before you start…

• Turn on the VCR and the TV.

• Set the T V to the video channel.

• Refer to “Index to parts and controls” for button locations.

Getting Started

PLAY

Press MENU, then press M/m to highlight SETTINGS a n d press OK.

Press M/m to highlight CLOCK, then press OK.

AUTO ADJUST is highlighted.

Press OK.

Press M/m to highlight ON, then press OK.

continued

Setting the clock

CONFIRM :

SELECT :

MENUEXIT :

CLOCK

AUTO ADJUST CLOCK PROGRAM MANUAL ADJUST

FRI 8 : 00

1 AAB

21.20019

CONFIRM :

SELECT :

MENUEXIT :

CLOCK

AUTO ADJUST CLOCK PROGRAM MANUAL ADJUST

.2001 FRI 8 : 00

8. 9

2 CDE

PLAY

Press m to highlight CLOCK PROGRAM, then press OK.

Press M/m repeatedly until the

PLAY

programme position of the station that carries a time signal appears.

If the VCR does not receive a time signal from any station, AUTO ADJUST returns to OFF automatically.

Tips

• If you set AUTO ADJUST to ON, the Auto Clock Set function is activated

• If you want to return to the previous menu, highlight RETURN and press OK.

Note

• The menu disappears automatically if you don’t pro cee d for more than a few

Press MENU to exit the menu.

whenever the VCR is turned off. The time is adjusted automatically by making reference to the time signal from the station whose programme positio n is displayed in the “CLOCK PROGRAM” row. If you do not need the Auto Clock Set, select OFF.

minutes.

Setting the clock

Selecting a language

SET :

SELECT :

MENUEXIT :

SETTINGS

RETURN

TUNER CLOCK LANGUAGE

SET :

SELECT

MENUEXIT :

LANGUAGE

You can change the on-screen display language from the one you selected with the Auto Set Up function.

Before you start…

• Turn on the VCR and the TV.

• Set the T V to the video channel.

• Refer to “Index to parts and controls” for button locations.

Getting Started

PLAY

Press MENU, then press M/m to highlight SETTINGS a n d press OK.

Press M/m to highlight LANGUAGE, then press OK.

Press M/m to highlight the desired language, then press OK.

Press MENU to exit the me nu.

Tip

• If you want to return to the previous menu, highlight RETURN and press OK.

Note

• The menu di sappears automatically if you don’t proceed for more th an a few minutes.

Selecting a language

Presetting channels

SET :

SELECT :

MENUEXIT :

SETTINGS

RETURN

TUNER CLOCK LANGUAGE

SET :

SELECT :

MENUEXIT :

TUNER

AAB12

PROG. 1

NORMAL / CATV CHANNEL SET PAY - TV / CANAL+ AFT FINE TUNING

NORMAL OFF

RETURN

SYSTEM D / K

MENUEXIT :

TUNER

CATV

PROG.

NORMAL / CATV CHANNEL SET PAY - TV / CANAL+ AFT FINE TUNING

NORMAL

RETURN

CONFIRM :

SELECT :

SYSTEM

SET :

SELECT :

MENUEXIT :

TUNER

AAB12

PROG. 1

NORMAL / CATV CHANNEL SET PAY - TV / CANAL+ AFT FINE TUNING

NORMAL OFF

RETURN

SYSTEM D / K

If some channels could not be preset using the Auto Set Up function, you can preset them manually.

Before you start…

• Turn on the VCR and the TV.

• Set the TV to the video channel.

• Refer to “Index to parts and controls” for button locations.

PLAY

Press MENU, then press M/m to highlight SETTINGS and press OK.

Press M/m to highlight TUNER, then press OK.

Press M/m to highlight NORMAL/ CATV, then press OK.

Press M/m to highlight NORMAL, then press OK.

To preset CATV (Cable Television) channels, select CATV.

Presetting channels

+ 70 hidden pages