Sony SLV-D100 Service Manual

Download

Page 1

SLV-D100

RMT-V501

SERVICE MANUAL

SPECIFICATIONS

System

Laser

Semiconductor laser

Format

VHS NTSC standard

Video recording system

Rotary head helical scanning FM system

Video heads

Double azimuth four heads

Video signal

NTSC color, EIA standards

Tape speed

SP: 33.35 mm/s (1 EP: 11.12 mm/s ( LP: 16.67 mm/s (

playback only

Maximum recording/playback time

8 hrs. in EP mode (with T-160 tape)

Rewind time

Approx. 1 min (with T-120 tape)

inches/s)

inches/s),

Tuner section

Channel coverage

VHF 2 to 13 UHF 14 to 69 CATV A-8 to A-1, A to W, W+1 to W+84

Antenna

75-ohm antenna terminal for VHF/UHF

Audio characteristics

Frequency response

DVD VIDEO (PCM 96 kHz): 2 Hz to 44 kHz (±1.0 dB)/DVD VIDEO (PCM 48 kHz): 2 Hz to 22 kHz (±0.5 dB)/CD: 2 Hz to 20 kHz (±0.5 dB)

Signal-to-noise ratio (S/N ratio)

115 dB (LINE OUT (L/R) AUDIO jacks only)

Harmonic distortion

0.003 %

Dynamic range

DVD VIDEO: 103 dB/CD: 99 dB

Wow and flutter

Less than detected value (±0.001% W PEAK)

The signals from LINE OUT L/R (AUDIO) jacks are measured. When you play PCM sound tracks with a 96 kHz sampling frequency, the output signals from the DIGITAL OUT (OPTICAL or COAXIAL) jack are converted to 48 kHz sampling frequency.

Inputs and outputs

LINE IN 1 and LINE-2 IN

VIDEO IN, phono jack (1 each) Input signal: 1 Vp-p, 75 ohms, unbalanced, sync

negative AUDIO IN, phono jacks (2 each) Input level: 327 mVrms Input impedance: more than 47 kilohms

Refer to the SERVICE MANUAL of VHS MECHANICAL ADJUSTMENT MANUAL VII for MECHANICAL ADJUSTMENTS. (9-921-790-11)

LINE OUT

VIDEO OUT, phono jack (1) Output signal: 1 Vp-p, 75 ohms, unbalanced,

negative

sync AUDIO OUT, phono jacks (2) Standard output: 327 mVrms Load impedance: 47 kilohms Output impedance: less than 10 kilohms

DIGITAL OUT

OPTICAL, Optical output jack –18 dBm (wave length: 660 nm) COAXIAL, phono jack Output signal: 0.5 Vp-p, 75 ohms

COMPONENT VIDEO OUT (Y, Pb, Pr)

Phono jack Y: 1.0 Vp-p/Pb, Pr: 0.7 Vp-p, 75 ohms

Timer section

Clock

Quartz locked

Timer indication

12-hour cycle

Timer setting

8 programs (max.)

US Model

Canadian Model

TS-10 MECHANISM

General

Power requirements

120 V AC, 60 Hz

Power consumption

29 W

Operating temperature

0°C to 45°C (32°F to 113°F)

Storage temperature

–20°C to 60°C (–4°F to 140°F)

Operating humidity

25% to 80%

Dimensions including projecting parts and controls (w/h/d)

Approx. 430 × 100 × 330 mm (Approx. 17 × 4 × 13 inches)

Mass

Approx. 4.5 kg (Approx. 9.9 lbs)

Supplied accessories

Remote commander (1) Size AA (R6) batteries (2) 75-ohm coaxial cable with F-type connectors (1) Audio/video cord (pinplug × 3 y pinplug × 3) (1)

Design and specifications are subject to change without

notice.

DVD PLAYER/

VIDEO CASSETTE RECORDER

Page 2

3 Pick-up Disassembly and Reassembly

3-1 Disassembly

1) Remove the power cord.

2) Disassemble the Deck-Assy.

3) Make solder land 2 points short on Pick-up. (See Fig. 1-3)

4) Disassembly the Pick-up.

Note: If the assembly and disassembly are not done in correct sequence, the Pick-up may be damaged.

PICK-UP ASS'Y

3-2 Assembly

1) Replace the Pick-up.

2) Remove the soldering 2 points on Pick-up.

3) Reassemble the Deck-Assy.

Fig.3

— 7 —

SOLDER LAND 2 POINTS SHORT

Page 3

3. Block Diagram

SLV-D100

3-2E3-1

Page 4

5-1 S.M.P.S.

5-65-5

Page 5

5-2 Power Drive

5-7 5-8

Page 6

5-3 Function-Timer

5-105-9

Page 7

5-4 Logic

5-11 5-12

Page 8

5-5 A/V

5-145-13

Page 9

5-6 Hi-Fi/MTS

5-15 5-16

Page 10

5-7 Input-Output

5-185-17

Page 11

5-8 DVD Main-Micom/AV Decoder

5-19 5-20

Page 12

5-9 DVD Servo

5-21 5-22

Page 13

5-10 DVD Audio/Video

5-23 5-24E

Page 14

SLV-D100

6. VCR Alignment and Adjustments

6-1 Reference

1) X-Point (Tracking center) adjustment, “Head switching adjustment” can be adjusted with remote control.

2) When replacing the VCR Main PCB Micom (IC601) and NVRAM (IC605 ; EEPROM) be sure to adjust the “Head switching adjustment”.

3) When replacing the cylinder ass’y, be sure to adjust the “X-Point” and “Head switching adjustment”.

4) How to adjustment.

- Monmently short-circuit the test point on Function-Timer PCB with pincers to set the adjustment mode.

- If the corresponding adjustment button is pressed, the adjustment is performed automatically.

6-1-1 Location of Adjustment Button of Remote Control

X-Point (Tracking Center)

Adjustment ; "5"

Head Switching

Adjustment ; "SP/EP"

Fig. 6-1

6-1

Page 15

6-1-2 TEST Location for Adjustment Mode Setting

Short-Circuit for a second and release.

Fig. 6-2 Function-Timer PCB (Top View)

6-2

Page 16

6-2 Mechanical Adjustment

Note : Refer to the Mechanical Manual “TS-10 (P/N: 9-921-790-11) for the adjustment and confirmation of ass’y full deck.

6-2-1 The Number and Position of Test Point

Test point : TP2 (Audio Output)

TP3 (Envelope) TP4 (H‘D S/W-Trigger) TP5 (Control Pulse)

CONTROL PULSE

HEAD SWITCHING

ENVELOPE

AUDIO OUTPUT

Fig. 6-3 Location of Test point (VCR Main PCB-Top View)

6-2-2 ACE Head Position (X-Point) Adjustment

(See the 2-2-1(d) ACE Head Position (X-Point) Adjustment on 2-2 of the Mechanical Manual)

1) Playback the alignment tape (Color bar).

2) Momently short-cricuit the test point on F/Timer PCB with pincers to set the adjustment mode.

(See Fig. 6-2)

3) Press the “5” button of remote control then adjustment is operated automatically. (See Fig. 6-1)

4) Connect the CH-1 probe to TP3 (Envelope) the CH-2 probe to TP4 (H’D switching pulse) and then trigger to CH-1.

5) Insert the (-) driver into the X-Point adjustment hole and adjust it so that envelope waveform is maximum.

6) Turn the Power off.

6-3

Page 17

6-3 Head Switching Point Adjustment

1) Playback the alignment tape.

2) Momently short-circuit the test point on Function-Timer PCB with pincers to set the adjustment mode. (See Fig. 6-2)

3) Press the “SP/EP” button of remote control then adjustment is operated automatically. (See Fig. 6-1)

6-4E

Page 18

7. Troubleshooting

(VCR Section)

EE-VIDEO

Insert the

cassette tape recorded by

another VCR and press

PLAY Button

See (Video Missing in EE Mode)

Yes

Play Indicator

in the display

Yes

Mechanism

operation

See (Mechanism doesn't

operate in play mode)

Yes

PB-VIDEO

See

(Video missing in play mode)

See (PB VIDEO)

audio mising in play mode

Yes

Press PLAY key in

remote control

Check IC601-5

Check Timer

Yes

Play Mode Inoperative

No Power

(Standby LED OFF)

Fuse F1SD01 is OK?

AL5.8V D1SS07.

Check IC701, DT701.

Change Fuse F1SD01.

Check Trans PT1SD1.

Yes

AL5V IC601-36, 51, 73.

Check D604, L601

AL5.8V

IC601-41, 69, 92.

(VCR MAIN PCB)

Check CN701 Wafer

Yes

Check CN701 Connector Wafer.

AL5V IC701-5, 20.

Data IN, OUT, CLK

IC701-2, 3, 4.

Yes

SLV-D100

7-1

Page 19

CAPSTAN

ROTATION

(S.T REEL)

IC601-1, 2

PROG.SW STATE

IC601-62, 63, 64

CHANGE IC601

CHECK

LOADING MOTOR

MECHANISM OR SW601

TAKE UP REEL SENSOR

SUPPLY REEL SENSOR

(PT601.PT602)

SEE

(CAPSTAN DOES NOT

ROTATE)

STOP MODE

YES

PULSE

YES

LOAD A TAPE AND

PRESS PLAY BUTTON

TURN VCR POWER ON

MECHANISM DOESN'T

OPERATE IN PLAY MODE

TAPE LOADING

OPERATION

(LOAD)

IC601-82:HIGH

IC601-87:LOW

(END SENSOR)

IC601-82

CYLINDER

ROTATION

SW 30Hz

IC601-23

CYL FG.PG

IC601-65

SEE IC610-2,

(CYLINDER DOES

NOT ROTATE)

CHECK

START/END SENSOR (S601/S602)

IC601

NO NO

LOW

YES

HIGH

YES

CHECK TAPE AND END SENSOR

CHECK LM B+ AND LM

(VCR Section)

7-2

Page 20

LOAD TAPE AND

PRESS F.FWD BUTTON

FAST FORWARD

DOESN'T OPERATE

F.FWD

INDICATOR IN

THE DISPLAY

PRESS FF

KEY IN REMOTE

CONTROL

MECHANISM

STATE

IC601-62, 63, 64

CHECK

MECHANISM

CHECK TIMER

CHANGE IC601-5

NO NO

YES

STOP

CAPSTAN MOTOR

ROTATION

SEE

(CAPSTAN DOES NOT

ROTATE)

SEE

(MECHANISM DOES NOT

OPERATE IN PLAY MODE)

STOP

YES

F.FWD

ROTATE

(VCR Section)

RECORD MODE

DOESN'T OPERATE

PLAY

OPERATION

LOAD VCR WITH A

BLANK TAPE AND

PRESS RECORD BUTTON

REC MODE

SAFETY TAB

D-REC A (H)

IC601-29. 30

SEE

(AUDIO MISSING IN

RECORD MODE)

CHANGE SW602 (REC SW)

CHECK IC601

CHANGE TAPE

SEE

(PLAY MODE

DOESN'T OPERATE)

EJECT NO

YES

REC-VIDEO

SEE

(VIDEO MISSING IN

RECORD MODE)

YES

(VCR Section)

7-3

Page 21

FWD SEARCH DOESN'T

OPERATE

PLAY

OPERATION

PRESS F.FWD FOR

FORWARD SEARCH

CHECK IC601

CHECK CAPSTAN

MOTOR

IS CAPSTAN

SPEED CHANGED?

OPERATION

NOISE BAR

LOCKING

END

ADJUST

A/CE HEAD

CHANGE DECK

CHANGE IC601

SEE

(PLAY DOESN'T OPERATE)

YES

(CONTROL PULSE)

IC601-76

YES

(VCR Section)

LOAD A TAPE

REWIND DOESN'T

OPERATE

F.FWD

OPERATION

PRESS REWIND

BUTTON

REW

INDICATOR IN

THE DISPLAY

PRESS REW

KEY IN REMOTE

CONTROL

MECHANISM

STATE

IC601-62, 63, 64

CHECK

MECHANISM

CHECK TIMER

CHECK

IC601-5

SEE

(FAST FORWARD

DOESN'T WORK)

YES

STOP

DOES CAPSTAN

MOTOR

ROTATE?

CHECK

IC601-46

(CM F/R)

SEE

(MECHANISM DOES NOT

OPERATE IN PLAY MODE)

YES

REW

YES

(VCR Section)

7-4

Page 22

TURN THE VCR

POWER ON AND

INSERT A TAPE

PRESS EJECT BUTTON

CASSETTE LOADING

MECHANISM

DOES NOT OPERATE

TAPE DETECTED

CST IN MODE

IC601-82:HIGH(5V)

IC601-87:LOW(0V)

CHANGE IC601

CHECK

START/END SENSOR

IC601

CHECK

DM B

LINE

CHANGE CAPSTAN MOTOR

NO NO

YES

IC601-58 (0V)

IC601-58 (5V)

CHECK

CASSETT LOADING

MECHANISM

YES

CN604-8 (12.5V)

YES

(VCR Section)

REV. SEARCH DOESN'T

OPERATE

PLAY

OPERATION

PRESS REWIND BUTTON

FOR REV. SEARCH

CHECK CAP F/R LINE

IS CAPSTAN

SPEED CHANGED?

OPERATION

FWD SEARCH

END

CHECK IC601

CHANGE DECK

CHANGE IC601

SEE

(PLAY DOESN'T OPERATE)

(PLAY MODE)

YES

CAP F/R

IC601-46

HIGH

(SEARCH MODE)

YES

LOW

CHECK IC601

H'D AMP/ENV COMP.

CHECK CAPSTAN

MOTOR

NOISE BAR

LOCKING

ADJUST

A/CE HEAD

(CONTROL PULSE)

IC601-76

YES

(VCR Section)

7-5

Page 23

VIDEO MISSING IN

RECORD MODE

PLACE THE VCR

RECORD MODE

VIDEO EE MODE

OPERATION

VIDEO SIGNAL

IC301-32

VIDEO SIGNAL

IC801-5

CHECK VIDEO HEAD

CHECK

IC801, C313

SEE

(VIDEO MISSING IN EE MODE)

YES

(VCR Section)

VIDEO SIGNAL

IC301-22

CHECK

C308, C305

FM VIDEO

IC301-70

CHANGE

IC301, R320

FM VIDEO

IC301-66 (SLP)

IC301-73 (SP)

CHECK

CN301 CONNECTION

PLACE VCR IN STOP MODE

VIDEO MISSING IN

EE MODE

TUNER MODE

OPERATION

VIDEO SIGNAL

IC801-18

APPLY VIDEO SIGNAL

TO FRONT VIDEO INPUT JACK AND

SET TO LINE MODE BY TV VIEW BUTTON.

CHECK JK801

VIDEO SIGNAL

CHECK

C830, R804

CHECK

SLV-D100U TO

TV CONNECTION.

YES

VIDEO SIGNAL

JK801

YES

VIDEO SIGNAL

IC801-25

VIDEO SIGNAL

IC801-28

CHECK TM401

ANTENNA IN

CHECK IC801-18 TO

TM401-20 LINE

VIDEO SIGNAL

TM401-20

CHECK IIC CLK,

DATA LINE

CHANGE IC801

IIC CLK, DATA

IC801-21, 22

(VCR Section)

7-6

Page 24

COLOR MISSING IN

RECORD MODE

(VIDEO IN)

RECORD MODE

COLOR SIGNAL

IC301-46

COLOR-KILLER

IC301-61(2V)

CHANGE IC301

CHECK THE REC LINE

CHANGE XT301

CHECK XT301

SEE PAGE 7-6

(VIDEO MISSING IN RECORD

MODE)

YES

NOTE: XT301 - Always (3.579545MHz)

(VCR Section)

VIDEO MISSING IN

PLAY MODE

VIDEO EE MODE

OPERATION

PLACE THE VCR PLAY MODE

CHANGE IC301 CHECK IC601, C622, C623, R638

CHECK

CN301 CONNECTION

CHECK

C305

CHECK

IC601-23

CHECK VIDEO

OUT LINE

SEE PAGE 7-6

(VIDEO MISSING IN EE MODE)

YES

NONO

VIDEO FM

IC301-14

VIDEO SIGNAL

IC301-22

VIDEO SIGNAL

IC301-26

VIDEO SIGNAL

IC601-47

VIDEO SIGNAL

IC801-7

H'D SW

IC301-57

YES

YES YES YES

CHECK IC801, R822, C804

(VCR Section)

7-7

Page 25

OSD PICTURE MISSING

CHECK

IC601-37, 38

(14.318)

CHECK

IC601-52, 53

(AFC)

CHANGE

IC601

CHECK C626, R639

CHECK C618, C619

YES

XTAL IN : 14.318MHz

OSC IN : 5~10MHz

(VCR Section)

COLOR MISSING IN

PLAY MODE

FM-ENV

IC301-14

COLOR SIGNAL

IC301-46

COLOR-KILLER

IC301-61(2V)

COLOR-ROTARY

IC301-57

CHANGE

IC301

CHECK IC301-48, 51

XT301

CHECK IC601-98

SEE PAGE 7-7

(VIDEO MISSING IN PLAY MODE)

YES

NOTE: XT301 - Always (3.579545MHz)

(VCR Section)

CHECK

IC301-26

7-8

Page 26

CHECK

(AUDIO MISSING IN EE MODE)

PLACE IN PB MODE

AUDIO MISSING IN

PB MODE

CHANGE IC501

YES

IC501-29, 30

AUDIO FM (MIXED)

AUDIO SELECT

CHECK C353

MONO

HI-FI

IC301-6

AUDIO SIGNAL

YES

CHECK

C346 AND CHANCE IC301

IC301-5

DC : 2.3V

YES

(VCR Section)

CHECK ACE HEAD C345, C346,

R326, R327, R329, R330

AND CHANGE IC301

CHECK IC501-27 (A.H'D SW)

C514, C513 AND CHANGE

CYLINDER OR IC501

PACE VCR IN STOP MODE

BLUE MISSING IN

STOP MODE

CHANGE IC601

SELECT LINE

MODE WITHOUT

INPUT SIGNAL

CHECK IC601-52, 53

(AFC)

CHECK R639, C626

YES

CHECK IC601-50

SYNC IN

CHECK R638, C622, C623

YES

CHECK IC601-37, 38

(14.318)

CHECK C618, C619

YES

(VCR Section)

7-9

Page 27

CHECK

OSC BLOCK

CHECK

R332

CHECK

R331, R332, R348

IC301-76

AUDIO SIGNAL

IC501-61

AUDIO SIGNAL

CHECK IC301-53, 54

CLOCK, DATA

CHECK

R515, C340, C336

YES

CHECK

IC301-79, C340

IC301-58 AND CHANGE IC301

CHANGE IC501

IC301-10

AUDIO SIGNAL

IC301-9

AUDIO SIGNAL

IC301-7

MIX SIGNAL

(AUDIO

70KHz)

CN303-1

OSCILLATION

CHECK (AUDIO MISSING

IN PB MODE)

CHECK

PB MODE

CHECK

ACE HEAD

MONO

YES

MISSING AUDIO

IC501-19, 32

AUDIO SIGNAL

IC501-21

AUDIO FM

CHECK

CYLINDER

CHECK R506 AND

CHANGE IC501

CHECK

C510, C520 AND CHANGE IC501

CHECK

(AUDIO MISSING

IN EE MODE)

AUDIO MISSING IN

REC MODE

MONO

HIFI

MONO

YES

IC501-39 : 4.3V

CHECK

SYSCON REC "H"

YES

(VCR Section)

7-10

Page 28

CAPSTAN DOES

NOT ROTATE

PLACE THE VCR

IN PLAY MODE

CN604-2

24V

CN604-3

AL 5V

CN604-9

2.7V CN604-5

2.7V

CN601-35

OUTPUT (PWM)

IC601-33

OUTPUT (PWM)

CHECK

CAPSTAN MOTOR

CHECK

R632, C615

CHECK R615, R630, C606

CHANGE

IC601

CHECK

IC601

CHECK

B+ IN THE POWER BLOCK

CHECK

5.8V AT AL5.8V LINE

IN THE POWER BLOCK

NO NO

YES

YES YES

(VCR Section)

PLACE VCR IN STOP MODE

AUDIO MISSING

IN EE MODE

CHECK

C535, C537, R510, R512, R511, R513

CHECK IC501

CHECK

C529, TUNER BLOCK

CHECK

R501, R503, R519, R520

INPUT SELECT MODE

IC501-9, 14

AUDIO SIGNAL

INPUT

IC501-48

AUDIO SIGNAL

INPUT

LINE

TUNER

YES

IC501-53, 57

AUDIO SIGNAL

YES

CHECK IC601

IC501-36

A.MUTE

YES

(VCR Section)

7-11

Page 29

DRUM DOES

NOT ROTATE

PLACE THE VCR IN

PLAY MODE

IC604-8

12V

CYL-SPEED

XT601-37, 38

(14.381)

CHECK

CYLINDER MOTOR

CHANGE

XT601, C618, C619

CHECK D-PG, D-FG

IC601-65

CHECK

12V AT PC12V LINE

IN THE POWER BLOCK

FASTER

YES

SLOWER

YES

(VCR Section)

7-12

Page 30

No focus incoming

FE in SIC1-25

is within specified range?

DRIC1-26, 27 output

are normal?

Check open state from

DRIC1 to pick-up.

Check RIC1 and A, B, C, D input.

Check DRIC1.

Yes

(DVD Section)

No Disc recognition

LD is outputted

from object lens at

play key input?

No focus incoming and

no disc occurs.

Yes

(DVD Section)

7-13

Page 31

NO LD CD ON

RIC1-21 is 5V?

Current exceeds 0.1A?

LD out pick-up replace.

Open check in related circuit.

Check MIC1

Yes

Divide RQ5 emitter terminal

voltage and 5V real voltage

difference into 10ohm.

(DVD Section)

No pick-up home positing

SLD, SIC1-34

output is normal?

Check the Sled Motor and connection

Check MIC1

Yes

SLED+, SLED-

DRICI-32, 33 output are

normal?

Check DRIC1

Yes

(DVD Section)

7-14

Page 32

FINE SEEK Check

FINE SEEK MIRR

signal (RIC1-46) is missing?

TZCO signal

(SIC1-24) is occurs?

Track incomming is

delayed?

TE is within

2V and 3V?

Pick-up transfer smooth.

Check RIC1 Peripheral curcuit.

Check SIC1 Peripheral curcuit.

Time out due to many jump counts.

Check SIC1 peripheral circuit.

SIC1-33 output

is normal?

DRIC1-28, 29

terminal outputs are

normal?

Check CN1 and pick-up.

Check MECHA.

Check RIC1-26 terminal.

Check DRIC1 peripheral circuit.

Yes

(DVD Section)

No Search Operation

MIRR, SIC1-157

output is normal?

Actual velocity occurs

at SIC1-34 terminal?

Actual velocity occurs

at DRIC1-32, 33 terminal?

Check RIC1 peripheral circuit.

RFAGCO, RIC1-72

output level is normal?

Check SIC1 peripheral circuit.

Check DRIC1 peripheral circuit.

Yes

TE occurs in

search range?

Focus On?

Yes

See "Fine Seek Check"

Yes

Check pick-up.

(DVD Section)

7-15

Page 33

Abnormal rotation of

disc motor

Input of RF signal

is normal? (PRICI-4)

EFMO, PLCK Input is

normal? (SIC1-97, 92)

SPD output is normal?

(SIC1-35)

After resoldering SIC1.

DRIC1-2 output (FG)

is normal?

DRIC1-10 signal

MON is "H" ?

Check or replace disc motor.

Check SIC1, MIC1.

Check DRIC1 soldering and power.

Check path to RIC1 and SIC1.

Check RIC1 soldering and power.

RIC1-70 output

are normal?

RIC1-71 output

is normal?

Check RIC1 peripheral

circuit and A, B, C, D.

Yes

After resoldering PRIC1, PRIC2.

(DVD Section), DVD Play

Abnormal rotation of

disc motor

Input of RF signal

is normal? (SIC1-15)

SPD output is normal?

(SIC1-35)

After resoldering SIC1.

DRIC1-2 output (FG)

is normal?

DRIC1-10 signal

MON is "H" ?

Check or replace disc motor.

Check SIC1, MIC1.

Check DRIC1 soldering and power.

Check path to RIC1 and SIC1.

Check RIC1 soldering and power.

RIC1-70 output

are normal?

RIC1-71 output

is normal?

Check RIC1 peripheral

circuit and A, B, C, D.

Yes

(DVD Section), CD Play

7-16

Page 34

CD/VCD/DVD L/R output error

(Mixed Audio output)

Normal DATA 0 is

input in AIC2-2?

Analog output of

AIC2-7, 8 is normal?

Check JACK1, JK801 Audio out

peripheral soldering shot, IC801.

Check ZIC1-121 output.

Check ZIC1-125

(CD/VCD ; 16.9344MHz,

DVD ; 18.432MHz)

Yes

AIC4-1, 7 output

is normal?

Check AIC4 peripheral circuit.

Yes

Base terminal level

of AQ3, AQ6 are 'L'

Check IC601-50 mute.

Yes

(DVD Section)

No Tray open/close

MIC1-48, 49 is

Open ; "L", "L" ?

Close ; "H", "H"?

Check DRIC1-35, 36

output at open/close

Check signal line state from

DRIC1-35, 36 to tray motor.

Micom (MIC1) error.

Check DRIC1.

Yes

(DVD Section)

7-17

Page 35

S-Video output error

DVD SETUP in OSD

Alt video is "Component"?

VIC1 2, 4, 6 signal?

(MM1567)

Change the Alt video mode to S-Video.

Check VIC1.

Yes

Check ZIC1.

(ZIVA4.1)

Yes

(DVD Section)

Digital output error

Output in ZIC1-127 is normal?

Output in

DOIC1-6, 8, 10 is

normal?

Check JACK1, DOIC2

peripheral soldering shot.

Check ZIC1 peripheral circuit.

Check DOIC1.

Yes

(DVD Section)

7-18

Page 36

CVBS output error

27MHz clock

input is normal at

pin 159 in ZIC1?

Analog output

is normal at pin 133

in ZIC1?

Check the connection between

pin 6 in XIC1 and pin 129 in ZIC1.

Check the soldering of ZIC1.

Yes

Analog signals are

inputted normally pin 26 in

CN01? (VCR MAIN PCB)

Yes

Analog signals are

inputted pin 13 in IC801

Yes

Check the connection between

pin 133 in ZIC1 (DVD MAIN PCB)

and CN01 (VCR MAIN PCB).

Check L804, C828, C827.

Check the IC801.

Pin of VDD_2.5 &

VDD-3.3 in Zic1 has

normal level?

Check the connection between pin 23, 24, 25

in (VCR)CN01 and pin 23, 24, 25 in CN4.

Yes

Video signal

IC801-25?

Yes

Check the JK801/RCA cable.

(DVD/VCR Section)

Y/Pr/Pb output error

DVD SETUP in OSD

Alt video is "Component"?

VIC1-24, 21, 18 signal?

(MM1567)

Change the Alt Video mode to component.

JACK1 soldering Check.

Yes

Check ZIC1.

(ZIVA 4.1)

VIC1-2, 4, 6 signal?

Check VIC1.

Yes

(DVD Section)

7-19E

Page 37

8. Repair Parts List

SLV-D100

8-1 Exploded Views - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

8-1-1 Cabinet Assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

8-1-2 VCR Mechanical Parts (Top Side) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

8-1-3 VCR Mechanical Parts (Bottom Side) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

8-1-4 DVD Mechanical Parts - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

8-2 Electrical Parts List - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

8-2

8-3

8-4

8-5

8-6

8-1

Page 38

8-1 Exploded Views

NOTE:

• -XX, -X mean standardized parts, so they may have some differences from the original one.

• Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.

8-1-1 Cabinet Assembly

DVD Mechanical Parts

• The mechanical parts with no reference number in the exploded views are not supplied.

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Les composants identifiés par une marque

0 sont critiquens pour la sécurité.

Ne les remplacer que par une pièce portant le numéro spécifié.

not supplied

VCR Mechanical Parts

not supplied

Ref. No. Part No. Description Remarks

1 3-078-577-01 ASSY PANEL FRONT (COMBO UC) 2 3-078-578-01 SPRING ETC-DOOR TRAY 3 3-078-630-01 DOOR TRAY 4 3-078-629-01 DOOR CASSETTE 5 3-078-579-01 SPRING ETC

6 1-817-010-11 CONNECTOR-HEADER 7 3-078-569-01 LEG (COMBO UC) 8 A-6066-057-A PWB DVD MOUNT

Ref. No. Part No. Description Remarks

9 3-078-599-01 ASSY CONNECTOR BOARD TM402B

0 10 1-824-674-11 POWER CORD EP2 SPT-2

11 3-078-574-01 CABINET TOP (COMBO UC) 12 3-075-256-01 SCREW TAP 3X12 13 3-075-262-01 SCREW BH 4X12

14 3-078-566-01 SCREW TAP M3 L10 BLK 15 1-477-582-11 COMMANDER STANDARD (RMT-V501) 16 3-078-598-01 BATTERY COVER (COMBO GRAY) (for RMT-V501)

8-2

Page 39

8-1-2 VCR Mechanical Parts (Top Side)

108

not supplied

109

not supplied

110

not supplied

112

not supplied

105

not supplied

124

107

106

102

not supplied

104

not supplied

123

103

114

not supplied

121

120

115

(OPTIONAL)

118

113

not supplied

101

Ref. No. Part No. Description Remarks

101 3-067-779-01 LEVER-#9 GUIDE 102 3-067-780-01 SPRING-#9 GUIDE 103 3-067-785-01 LEVER-T. BRAKE 104 3-067-786-01 SPRING-BRAKE 105 3-067-782-01 SPRING-TENSION LEVER

106 3-067-781-01 LEVER-TENSION 107 3-067-783-01 BAND-BREAK 108 3-067-788-01 HOLDER-FL CASS. 109 1-796-436-11 ASSY CLYNDER 6HD (J) 110 3-075-253-01 SCREW ASSY MAC 2.6X5

111

Ref. No. Part No. Description Remarks 111 3-075-254-01 SCREW ASSY MAC 3X6

112 3-067-784-01 LEVER-UNIT PINCH 113 3-075-257-01 SCREW TAP 2.6X5 114 3-075-241-01 ASSY ACE HEAD 115 3-067-789-01 GUIDE-CASS. DOOR

118 1-763-836-11 LOADING ASSY, MOTOR 120 3-067-787-01 LEVER-FL DOOR 121 3-067-796-01 PLATE-GROUND DECK 123 3-075-046-01 DISK T REEL 124 3-075-047-01 DISK S REEL

8-3

Page 40

8-1-3 VCR Mechanical Parts (Bottom Side)

not supplied

151

not supplied

154

152

not supplied

not supplie

not supplied

Ref. No. Part No. Description Remarks

151 3-067-790-01 BELT-PULLEY 152 1-763-835-11 MOTOR CAPSTAN

not supplied

153

Ref. No. Part No. Description Remarks

153 3-075-259-01 SCREW CAP 2.6X6 154 3-075-260-01 SCREW MAC 3X3

8-4

Page 41

8-1-4 DVD Mechanical Parts

218

201

not supplied

203

202

not supplied

206

not supplied

204

not supplied

205

214

207

208 209

216

215

not supplied

Ref. No. Part No. Description Remarks

201 3-078-586-01 TRAY DISC 202 1-796-534-11 LOADING ASSY, MOTOR 203 3-078-583-01 BELT RECTANGULAR

0 204 1-796-530-11 ASSY PICK UP

205 3-078-588-01 SHAFT PU

217

213

210

211

212

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Les composants identifiés par une marque

0 sont critiquens pour la sécurité.

Ne les remplacer que par une pièce portant le numéro spécifié.

Ref. No. Part No. Description Remarks

210 1-796-537-11 FEED ASSY, MOTOR 211 3-078-589-01 GEAR FEED A 212 3-078-590-01 GEAR FEED B 213 3-078-591-01 WASHER SLIT 214 3-078-587-01 SCREW MAC 2.6X7

206 1-796-536-11 ASSY MOTOR-SPINDLE 207 3-078-597-01 SPRING ETC SPINDOLE CHASSIS SUB 208 3-078-592-01 SCREW TAP 2X6 209 3-078-596-01 RUBBER INSULATOR

215 3-078-593-01 SCREW SPE SWRCH18A 216 3-078-594-01 SCREW MAC 2X6 217 3-078-595-01 SCREW MAC MOTOR 218 1-761-641-11 ASSY DVD DECK DP-7S COMBO

8-5

Page 42

DVD MAIN

8-2 Electrical Parts List

NOTE:

•Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set.

• -XX, and -X mean standardized parts, so they may have some difference from the original one.

• RESISTORS All resistors are in ohms. METAL: metal-film resistor METAL OXIDE: Metal Oxide-film resistor F: nonflammable

• Not all of the parts are listed.

Ref. No. Part No. Description Remarks

A-6066-057-A DVD MAIN BOARD, COMPLETE

*************************

3-075-255-01 SCREW TAP 3X8

< DIODE >

AD1 1-805-012-11 DIODE DAN202K AD2 1-805-012-11 DIODE DAN202K AD3 1-805-012-11 DIODE DAN202K AD4 1-805-009-11 DIODE SWITCHING DAN217 AD5 1-805-012-11 DIODE DAN202K

• Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.

• SEMICONDUCTORS In each case, u: µ, for example: uA...: µA... , uPA... , µPA... , uPB... , µPB... , uPC... , µPC... , uPD..., µPD...

• CAPACITORS: uF: µF

• COILS uH: µH

When indicating parts by reference number, please include the board name.

The components identified by mark 0 or dotted line with mark Replace only with part number specified.

Les composants identifiés par une marque

0 sont critiquens pour la sécurité.

Ne les remplacer que par une pièce portant le numéro spécifié.

Ref. No. Part No. Description Remarks

PRIC1 1-805-040-11 IC ASIC S5LR010X01 PRIC2 1-805-022-11 IC CMOS LOGIC 74VHCT125A SIC1 1-805-037-11 IC ASIC KS1454 SIC2 1-805-033-11 IC DRAM 416C256 SIC4 1-805-019-11 IC CMOS LOGIC 7ST08

VIC1 1-805-029-11 IC VIDEO AMP MM1567A XIC1 1-805-039-11 IC M74HCU04 ZIC1 1-805-036-11 IC DECODER ZIVA4.1 B0 ZIC2 1-805-034-11 IC DRAM 4S641632

< COIL >

0 are critical for safety.

AD6 1-805-013-11 DIODE DAP202K PD1 1-805-010-11 DIODE 1SR154-400 RD1 1-805-013-11 DIODE DAP202K VZ1 1-805-011-11 DIODE UDZ9.1B VZ2 1-805-011-11 DIODE UDZ9.1B

VZ3 1-805-011-11 DIODE UDZ9.1B VZ4 1-805-011-11 DIODE UDZ9.1B VZ5 1-805-011-11 DIODE UDZ9.1B VZ6 1-805-011-11 DIODE UDZ9.1B VZ7 1-805-011-11 DIODE UDZ9.1B

VZ8 1-805-011-11 DIODE UDZ9.1B VZ9 1-805-011-11 DIODE UDZ9.1B VZ10 1-805-011-11 DIODE UDZ9.1B

< IC >

AIC2 1-805-024-11 IC DA CONVERTER AIC4 1-805-028-11 IC OP AMP 4560 AIC5 1-805-028-11 IC OP AMP 4560 DOIC1 1-805-039-11 IC M74HCU04 DRIC1 1-805-025-11 IC MOTOR DRIVER KA3017

MIC1 1-805-023-11 IC MICOM 91C829 MIC2 1-805-026-11 IC EPROM 27C081 MIC3 1-805-027-11 IC EEPROM 24C021 MIC5 1-805-020-11 IC CMOS LOGIC 7S32 MIC6 1-805-021-11 IC CMOS LOGIC 7SET00

MIC7 1-805-019-11 IC CMOS LOGIC 7ST08 PIC1 1-805-030-11 IC V REGULATOR 1563 PIC2 1-805-032-11 IC V REGULATOR MM1561 PIC3 1-805-031-11 IC V REGULATOR 3RD13 RIC1 1-805-038-11 IC ASIC KS1462B

AL1 1-400-316-11 INDUCTOR 0uH AL2 1-400-316-11 INDUCTOR 0uH DOL1 1-400-315-11 INDUCTOR 0uH DOL2 1-400-316-11 INDUCTOR 0uH RL1 1-400-316-11 INDUCTOR 0uH

VL1 1-400-316-11 INDUCTOR 0uH VL2 1-400-316-11 INDUCTOR 0uH VL3 1-400-316-11 INDUCTOR 0uH VL4 1-400-316-11 INDUCTOR 0uH VL7 1-400-316-11 INDUCTOR 0uH

VL8 1-400-316-11 INDUCTOR 0uH VL9 1-400-316-11 INDUCTOR 0uH VL10 1-400-316-11 INDUCTOR 0uH VL11 1-400-316-11 INDUCTOR 0uH XL1 1-400-316-11 INDUCTOR 0uH

XL2 1-400-316-11 INDUCTOR 0uH ZL1 1-400-316-11 INDUCTOR 0uH ZL4 1-400-316-11 INDUCTOR 0uH ZL5 1-400-316-11 INDUCTOR 0uH ZL7 1-400-316-11 INDUCTOR 0uH

ZL8 1-400-316-11 INDUCTOR 0uH

< TRANSISTOR >

AQ1 1-805-017-11 TRANSISTOR 200MW AQ2 1-805-018-11 TRANSISTOR KSR2103 AQ3 1-805-016-11 TRANSISTOR KSC1623-L AQ4 1-805-017-11 TRANSISTOR 200MW AQ5 1-805-018-11 TRANSISTOR KSR2103

AQ6 1-805-016-11 TRANSISTOR KSC1623-L

8-6

Page 43

VCR MAINFUNCTION-TIMERDVD MAIN

Ref. No. Part No. Description Remarks

AQ7 1-805-017-11 TRANSISTOR 200MW AQ8 1-805-018-11 TRANSISTOR KSR2103 AQ9 1-805-015-11 TRANSISTOR KSA812 AQ11 1-805-016-11 TRANSISTOR KSC1623-L

AQ12 1-805-016-11 TRANSISTOR KSC1623-L PRQ1 1-805-016-11 TRANSISTOR KSC1623-L RQ1 1-805-016-11 TRANSISTOR KSC1623-L RQ2 1-805-016-11 TRANSISTOR KSC1623-L RQ3 1-805-016-11 TRANSISTOR KSC1623-L

RQ4 1-805-014-11 TRANSISTOR KSA1182-Y RQ5 1-805-014-11 TRANSISTOR KSA1182-Y SQ1 1-805-018-11 TRANSISTOR KSR2103

< VAIBRATOR >

MY1 1-795-751-11 RESONATOR CERAMIC (20MHz) SY1 1-795-749-11 CRYSTAL UNIT (33.8688MHz) XY1 1-795-750-11 CRYSTAL UNIT (27MHz)

FUNCTION-TIMER BOARD, COMPLETE

*******************************

< DIODE >

D701 1-804-407-11 DIODE IN4148 D702 1-804-407-11 DIODE IN4148 D703 1-804-407-11 DIODE IN4148 D704 1-804-407-11 DIODE IN4148 DT701 1-518-848-11 LED DISPLAY LTG-0208M (LITE-ON)

< IC >

IC701 1-804-706-11 IC LED DRIVER RM701 1-805-007-11 IC MODULE, REMOCON

Ref. No. Part No. Description Remarks

VCR MAIN BOARD, COMPLETE

*************************

3-075-066-01 HOLDER-SENSOR

< COIL >

BD1SS1 1-400-085-11 INDUCTOR 0uH BD1SS2 1-400-085-11 INDUCTOR 0uH BD1SS3 1-400-085-11 INDUCTOR 0uH L302 1-400-085-11 INDUCTOR 0uH L303 1-400-085-11 INDUCTOR 0uH

L1SS01 1-456-179-11 COIL-LINE FILTER 25mH L1SS02 1-424-828-11 COIL CHOKE 10uH L1SS03 1-424-828-11 COIL CHOKE 10uH L1SS04 1-424-828-11 COIL CHOKE 10uH L1SS05 1-424-828-11 COIL CHOKE 10uH

< CAPACITOR >

0 C1SD02 1-165-992-11 CAPACITOR 10000pF 0 C1SD03 1-165-557-11 CAPACITOR 2200pF 0 C1SS01 1-165-573-11 FILM 0.1uF 0 C1SS04 1-100-358-11 CERAMIC DISC 100pF

< DIODE >

D1P101 1-804-409-11 DIODE IN4002 D1P102 1-804-409-11 DIODE IN4002 D1P103 1-804-407-11 DIODE IN4148 D1P104 1-804-407-11 DIODE IN4148 D1P105 1-804-407-11 DIODE IN4148

D1P107 1-804-407-11 DIODE IN4148 D1P108 1-804-407-11 DIODE IN4148 D1SR10 1-804-407-11 DIODE IN4148 D1SR11 1-804-407-11 DIODE IN4148 D1SS01 1-804-413-11 DIODE IT5

< COIL >

L701 1-400-074-11 INDUCTOR 0uH

< SWITCH >

SW701 1-786-354-11 TACT SW (BULK 5MM) (EJECT) SW702 1-786-354-11 TACT SW (BULK 5MM) (VCR) SW703 1-786-354-11 TACT SW (BULK 5MM) (DVD) SW704 1-786-354-11 TACT SW (BULK 5MM) (REC) SW705 1-786-354-11 TACT SW (BULK 5MM) (CH UP)

SW706 1-786-354-11 TACT SW (BULK 5MM) (CH DOWN) SW707 1-786-354-11 TACT SW (BULK 5MM) (OPEN/CLOSE) SW708 1-786-354-11 TACT SW (BULK 5MM) (FF) SW709 1-786-354-11 TACT SW (BULK 5MM) (PLAY) SW710 1-786-354-11 TACT SW (BULK 5MM) (REW)

SW711 1-786-354-11 TACT SW (BULK 5MM) (STOP) SW712 1-786-354-11 TACT SW (BULK 5MM) (POWER) SW713 1-786-354-11 TACT SW (BULK 5MM) (P/STILL)

PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPP

D1SS02 1-804-413-11 DIODE IT5 D1SS03 1-804-413-11 DIODE IT5 D1SS04 1-804-413-11 DIODE IT5 D1SS05 1-805-041-11 DIODE SCHOTTKY SE55 D1SS07 1-805-041-11 DIODE SCHOTTKY SE55

D1SS08 1-805-041-11 DIODE SCHOTTKY SE55 D1SS09 1-804-407-11 DIODE IN4148 D1SS10 1-804-407-11 DIODE IN4148 D1SS11 1-804-408-11 DIODE UF4007 D1SS12 1-804-412-11 DIODE FIT4

D1SS13 1-804-411-11 DIODE UG2D D1SS15 1-804-412-11 DIODE FIT4 D503 1-804-407-11 DIODE IN4148 D601 1-804-407-11 DIODE IN4148 D603 1-804-409-11 DIODE IN4002

D604 1-804-409-11 DIODE IN4002 D605 1-804-407-11 DIODE IN4148 D606 1-804-409-11 DIODE IN4002 D801 1-804-407-11 DIODE IN4148 D803 1-804-407-11 DIODE IN4148

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number

8-7

specified.

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

Page 44

VCR MAIN

Ref. No. Part No. Description Remarks

D804 1-804-407-11 DIODE IN4148 D813 1-804-407-11 DIODE IN4148 D814 1-804-407-11 DIODE IN4148 LD601 1-804-438-11 LED-IR ZD1P01 1-804-414-11 DIODE ZENER UZP33B

ZD1P02 1-804-418-11 DIODE ZENER MTZJ12B ZD1P03 1-804-417-11 DIODE ZENER MTZJ9.1B ZD1P04 1-804-416-11 DIODE ZENER MTZJ5.1B ZD1P05 1-804-418-11 DIODE ZENER MTZJ12B ZD1P06 1-804-416-11 DIODE ZENER MTZJ5.1B

ZD1SS1 1-804-415-11 DIODE ZENER UZP43B

< FUSE >

0 F1SD01 1-576-525-11 FUSE (1.6A/250V)

< IC >

IC1SS1 1-804-784-11 IC PHOTO COUPLER IC1SS2 1-804-445-11 IC KA4318 IC301 1-804-772-11 IC VIDEO LA71201 IC501 1-804-434-11 IC AN3663FBP IC601 1-805-006-11 IC MICON MN101D06F

IC603 1-805-042-11 IC EEPROM 524C80D41 IC6B1 1-804-444-11 IC KA7533 IC801 1-805-035-11 IC AUDIO LA73024V

< PHOTO INTERRUPTER >

PT601 1-804-770-11 TRANSISTOR PHOTO INTERRUPTER PT602 1-804-770-11 TRANSISTOR PHOTO INTERRUPTER

< TRANSFORMER >

0 PT1SD1 1-437-943-11 TRANS SWITCHING EER3530

Ref. No. Part No. Description Remarks

Q601 1-804-428-11 TRANSISTOR KSR1004

< PHOTO TRANSISTOR >

S601 1-804-439-11 PHOTO TRANSISTOR S602 1-804-439-11 PHOTO TRANSISTOR

< SWITCH >

SW602 1-786-199-11 SWITCH REC SW603 1-786-198-11 SWITCH MODE

< TUNER >

TM401 1-693-551-11 TUNER NTSC

< VARISTOR >

0 VA1SS1 1-804-437-11 VARISTOR PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPP

MISCELLANEOUS

***************

6 1-817-010-11 CONNECTOR-HEADER

0 10 1-824-674-11 POWER CORD EP2 SPT-2

109 1-796-436-11 ASSY CLYNDER 6HD (J) 118 1-763-836-11 LOADING ASSY, MOTOR 152 1-763-835-11 MOTOR CAPSTAN

202 1-796-534-11 LOADING ASSY, MOTOR

0 204 1-796-530-11 ASSY PICK UP

206 1-796-536-11 ASSY MOTOR-SPINDLE 210 1-796-537-11 FEED ASSY, MOTOR 218 1-761-641-11 ASSY DVD DECK DP-7S COMBO

PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPP

< TRANSISTOR >

Q1P101 1-804-424-11 TRANSISTOR KSC2328AY Q1P102 1-804-429-11 TRANSISTOR KSR2001 Q1P103 1-804-421-11 TRANSISTOR KSC945 Q1P104 1-804-421-11 TRANSISTOR KSC945 Q1P105 1-804-424-11 TRANSISTOR KSC2328AY

Q1P106 1-804-424-11 TRANSISTOR KSC2328AY Q1P107 1-804-424-11 TRANSISTOR KSC2328AY Q1P108 1-804-429-11 TRANSISTOR KSR2001 Q1P109 1-804-421-11 TRANSISTOR KSC945 Q1P110 1-804-424-11 TRANSISTOR KSC2328AY

Q1P111 1-804-424-11 TRANSISTOR KSC2328AY Q1SD11 1-804-767-11 TRANSISTOR POWER Q1SR12 1-804-422-11 TRANSISTOR KTC3023 Q302 1-804-420-11 TRANSISTOR KSA733 Q303 1-804-421-11 TRANSISTOR KSC945

Q304 1-804-420-11 TRANSISTOR KSA733 Q305 1-804-422-11 TRANSISTOR KTC3023 Q306 1-804-420-11 TRANSISTOR KSA733 Q307 1-804-422-11 TRANSISTOR KTC3023 Q308 1-804-422-11 TRANSISTOR KTC3023

8-8

ACCESSORIES & PACKING MATERIALS

********************************

1-477-582-11 COMMANDER STANDARD (RMT-V501) 3-077-210-12 MANUAL, INSTRUCTION (ENGLISH) 3-077-210-22 MANUAL, INSTRUCTION (FRENCH) 3-078-598-01 BATTERY COVER (COMBO GRAY) (for RMT-V501)

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

Sony SLV-D100 Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

DVD MAIN

VCR MAINFUNCTION-TIMERDVD MAIN