Sony MHC-ZX30AV Operating Instruction

Mini Hi-Fi Component System

Operating Instructions

4-227-889-12(1)

MHC-ZX30AV

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.

This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.

NOTICE FOR THE CUSTOMERS IN CANADA

CAUTION

TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS POLARIZED AC PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

ENERGY STAR

As ENERGY STAR® Partner, Sony Corporation has determined that this product meets the ENERGY

STAR

This stereo system is equipped with the Dolby B-type noise reduction system*. * Manufactured under license from Dolby

Laboratories Licensing Corporation. DOLBY and the double-D symbol ; are trademarks of Dolby Laboratories Licensing Corporation.

is a U.S. registered mark.

guidelines for energy efficiency.

Table of Contents

Getting Started

Step 1: Hooking up the system ................ 4

Step 2: Setting up your speakers .............. 7

Step 3: Setting the time ............................ 9

Step 4: Presetting radio stations ............. 10

Saving the power in standby mode* ....... 12

Basic Operations

Playing a CD ........................................... 13

Recording a CD....................................... 15

Listening to the radio .............................. 16

Recording from the radio ........................ 18

Playing a tape .......................................... 19

Recording from a tape ............................. 22

The CD Player

Using the CD display .............................. 23

Playing the CD tracks repeatedly ............ 24

Playing the CD tracks in random order... 25

Programming the CD tracks.................... 26

The Tape Deck

Recording on a tape manually................. 28

Recording a CD by specifying track order

.......................................................... 29

DJ Effects

Looping part of a CD .............................. 32

Flashing part of a CD .............................. 33

Sound Adjustment

Adjusting the sound ................................ 33

Selecting the preset audio effect file ....... 34

Changing the spectrum analyzer display 36

Selecting surround effects ....................... 37

Enjoying Dolby Pro Logic Surround sound

.......................................................... 38

Controlling the graphic equalizer............ 39

Creating a personal audio effect file ....... 40

Other Features

Using the Radio Data System (RDS)** .. 41

Falling asleep to music............................ 43

Waking up to music ................................ 44

Timer-recording radio programs ............. 46

Optional components

Connecting audio components ................ 48

Connecting a VCR .................................. 50

Connecting a DVD player ....................... 50

Connecting external antennas ................. 51

Additional Information

Precautions .............................................. 53

Troubleshooting ...................................... 54

Specifications .......................................... 57

Parts Identification for the remote .......... 60

Index........................................................ 61

Items in “Sound Mode” and “Set Up

Mode” ................................. Back cover

* Canadian and European models only **European model only

Getting Started

Step 1: Hooking up the system

Follow steps 1 through 6 of the following procedure to hook up your system using the supplied cords and accessories.

FM antenna

AM loop antenna

Rear speaker (Right)

Front speaker (Right)

1 Connect the front speakers.

Connect the speaker cords of the front speakers to the FRONT SPEAKER jacks as below.

Insert only the stripped portion.

Center speaker

2 3

Rear speaker (Left)

Front speaker (Left)

Notes

• Keep the speaker cords away from the antennas to prevent noise.

• The type of speakers supplied vary according to the model you purchased (see “Specifications” on page 57).

Red (3)

–

Black (#)

2 Connect the rear speakers.

Connect the speaker cords of the rear speakers to the REAR SPEAKER jacks.

Insert only the stripped portion.

4 Connect the FM/AM antennas.

Set up the AM loop antenna, then connect it.

Jack type A

AM loop antenna

Extend the FM lead antenna horizontally.

Getting Started

Red/Solid (3)

Notes

Black/Stripe (#)

• Keep the speaker cords away from the antennas to prevent noise.

• Do not place the rear speakers on top of a TV. This may cause color distortion in the TV screen.

3 Connect the center speaker.

Connect the speaker cords of the center speaker to the CENTER SPEAKER jacks.

Insert only the stripped portion.

Red/Solid (3)

Black/Stripe (#)

Note

Keep the speaker cords away from the antennas to prevent noise.

–

FM75

Jack type B

Extend the FM lead antenna horizontally.

AM loop antenna

FM75 COAXIAL

5 For models with a voltage selector, set

VOLTAGE SELECTOR to the position of your local power line voltage.

VOLTAGE SELECTOR

120V

230

240V

220V

continued

Step 1: Hooking up the system (continued)

6 Connect the power cord to a wall outlet.

If the supplied adapter on the plug does not fit your wall outlet, detach it from the plug (only for models equipped with an adapter).

To connect optional components

See page 48.

To deactivate/activate the demonstration

When you set the time (“Step 3: Setting the time” on page 9), the demonstration is deactivated.

To activate/deactivate the demonstration again, press DISPLAY repeatedly while the system is off.

Tip

You can reinforce the bass sound by connecting an optional super woofer to the super woofer connector.

To attach the front speaker pads

Attach the supplied front speaker pads to the bottom of the speakers to stabilize the speakers and prevent them from slipping.

Inserting two size AA (R6) batteries into the remote

]

}

]

Tip

With normal use, the batteries should last for about six months. When the remote no longer operates the system, replace both batteries with new ones.

Note

If you do not use the remote for a long period of time, remove the batteries to avoid possible damage from battery leakage.

When carrying this system

Do the following to protect the CD mechanism. Make sure that all discs are removed from the unit.

1 Press FUNCTION repeatedly until “CD”

appears in the display.

2 Hold down V-GROOVE and press ?/1 so that

“LOCK” appears in the display.

Step 2: Setting up your speakers

Connecting the supplied rear and center speakers enables you to fully enjoy Dolby Pro Logic Surround sound. Dolby Pro Logic Surround is a decoding system standardized in TV programs and movies. Dolby Pro Logic Surround improves the sound image by using four separate channels. These channels manipulate the sound to be heard and enhance the action of the TV screen.

Positioning the speakers

Before you connect the speakers, determine the best location for them.

1 Place the front speakers at an angle of

45 degrees from your listening position.

2 Place the center speaker at about the

same height as the front speakers (A). Align the center speaker with the front speakers or place it slightly behind the front speakers (B).

Center

speaker

Getting Started

Front

speaker (L)

Rear

speaker (L)

Center

speaker

45°

Front

speaker (R)

Rear

speaker (R)

3 Place the rear speakers facing each

other at about 60 to 90 cm above your listening position.

Rear speaker

60 to 90 cm

continued

Step 2: Setting up your speakers (continued)

Adjusting the speaker volume

To enjoy Dolby Pro Logic Surround sound, turn on the Dolby Pro Logic mode, then adjust the volume of each speaker using the test tone provided by the system.

MODE SELECT

?/1

(Power)

Multi stick

PUSH ENTER

1 Press PRO LOGIC (or PRO LOGIC

ON/OFF on the remote).

“PRO LOGIC ON” appears.

2 Press T.TONE ON/OFF on the remote.

Each speaker will emit a test tone in the following order. Adjust the volume of the test tone.

t LEFT t CENTER t RIGHT

REAR L T REAR R T

3 From your listening position, press

CENTER LEVEL (+/–) and REAR LEVEL (+/–) on the remote to adjust the volume.

For the rear level, the rear right speaker will emit sound.

The volume levels from each speaker must become the same.

4 Press T.TONE ON/OFF when you are

done adjusting.

The test tone turns off.

h H

MmX

VOLUME

B/b

1 2, 4

VOLUME +/–

Tip

If you turn VOLUME (or press VOLUME +/– on the remote) all the speaker volumes change.

Note

The test tone feature works only for Dolby Pro Logic Surround sound.

To adjust the speaker balance

You can adjust the balance of the front speakers and the rear speakers.

1 In step 2 above, select RIGHT, LEFT or

CENTER to adjust the front balance, and select REAR R or REAR L to adjust the rear balance.

2 Press B or b on the remote (or move the multi

stick on the unit toward b or B) and adjust the balance.

Tip

You can adjust the speaker balance using the “Sound Mode” menu. 1 Press MODE SELECT repeatedly to select “Sound

Mode”, then press PUSH ENTER.

2 Move the multi stick toward b or B repeatedly to

select “Front Balance” or “Rear Balance”, then press PUSH ENTER.

3 Move the multi stick toward b or B repeatedly to

adjust the balance, then press PUSH ENTER.

Step 3: Setting the time

3 Move the multi stick toward v or V

repeatedly to set the hour.

You must set the time before using the timer functions.

The clock is on a 24-hour system for the European model, and on a 12-hour system for other models.

For illustration purposes, the 24-hour system model is used.

?/1

(Power)

2,3,4,5,6

1 Press MODE SELECT when the system

is turned off.

“Clock Set ?” appears. When the system is in the Power Saving Mode, “Clock Set ?” will not appear. Either set Power Saving Mode off, or follow the steps on the following page (“To change the time”) after turning the power on.

4 Move the multi stick toward B.

The minute indication flashes.

5 Move the multi stick toward v or V

repeatedly to set the minute.

6 Press PUSH ENTER.

To cancel the menu operation

Press MODE SELECT.

Tips

• Refer to the illustration to use the multi stick. Place your finger on the center of the multi stick and move in the direction you want (up/down or left/ right shown v/V or b/B in this manual).

Up (v)

PUSH

Left (b)

• If you’ve made a mistake, start over from step 1.

ENTER

Down (V)

Right (B)

continued

Getting Started

2 Press PUSH ENTER.

The hour indication flashes.

Step 3: Setting the time (continued)

To change the time

The previous explanation shows you how to set the time while the power is off. To change the time while the power is on, do the following:

1 Press MODE SELECT repeatedly to select “Set

Up Mode”, then press PUSH ENTER.

2 Move the multi stick toward b or B repeatedly

to select “Timer Set Up ?”, then press PUSH ENTER.

3 Move the multi stick toward b or B repeatedly

to select “Clock Set ?”, then press PUSH ENTER.

4 Perform steps 3 through 6 on page 9. Note

The clock settings are canceled when you disconnect the power cord or if a power failure occurs.

Step 4: Presetting radio stations

You can preset a total of 30 stations (20 for FM and 10 for AM).

?/1

(Power)

Multi stick PUSH ENTER

. >

1 Press TUNER/BAND repeatedly to

select FM or AM.

2 Press and hold m or M until the

frequency indication starts to change, then release.

Scanning stops automatically when a station is tuned in. “TUNED” and “STEREO” (for a stereo program) appear.

TUNED

STEREO

3 Press MODE SELECT repeatedly to

select “Set Up Mode”, then press PUSH ENTER.

4 Move the multi stick toward b or B

repeatedly to select “TUNER Set Up ?”, then press PUSH ENTER.

5 Move the multi stick toward b or B

repeatedly to select “TUNER Memory ?”, then press PUSH ENTER.

A preset number and the frequency appear in the display. The stations are stored from preset number 1 automatically.

Preset number

6 Press PUSH ENTER. 7 Repeat steps 2 through 6 to store other

stations.

To cancel the menu operation

Press MODE SELECT.

To tune in a station with a weak signal

Press m or M repeatedly in step 2 to tune in the station manually.

To set another station to an existing preset number

Start over from step 1. After step 5, press . or > to select the preset number where you want

to store the other station, then press PUSH ENTER.

You can preset a station in the selected preset number.

To erase a preset station

1 Press TUNER/BAND to select FM or AM. 2 Press MODE SELECT repeatedly to select

“Set Up Mode”, then press PUSH ENTER.

3 Move the multi stick toward b or B repeatedly

to select “TUNER Set Up ?”, then press PUSH ENTER.

4 Move the multi stick toward b or B repeatedly

to select “TUNER Erase ?”, then press PUSH ENTER.

5 Move the multi stick toward b or B repeatedly

to select the preset number you want to erase, then press PUSH ENTER.

Select “TUNER Ers FM ALL” (or “TUNER Ers AM ALL”) when you want to erase all the preset stations.

When you erase a preset number, the preset number decreases by one and all preset numbers following the erased one are renumbered.

Tip

The preset stations are retained for half a day even if you unplug the power cord or a power failure occurs.

To change the AM tuning interval (Except for the European and Middle Eastern models)

The AM tuning interval is factory-preset to 9 kHz (10 kHz in some areas). To switch the AM tuning interval, tune in any AM station first, then turn off the power. While holding down MODE SELECT, turn the power back on. When you switch the interval, AM preset stations are erased. To switch back to the original interval, repeat the same procedure.

Getting Started

Saving the power in standby mode

(Canadian and European models only)

You can lower the power consumption to a minimum (Power Saving Mode) and save energy in the standby mode.

?/1

(Power)

DISPLAY

Tips

• ?/1 indicator and timer indicator (when the timer is set) light even in the Power Saving Mode.

• The timer functions in the Power Saving Mode.

Notes

• You cannot set the time in the Power Saving Mode.

• One Touch Play function does not work in the Power Saving Mode.

To cancel the Power Saving Mode

Press DISPLAY once to show the demonstration, twice to show the clock display.

, Press DISPLAY repeatedly when the

power is off.

Each time you press the button, the display changes as follows:

t Demonstration t clock

Power Saving Mode T

The system is turned on/off by pressing ?/1.

Basic Operations

Playing a CD

— Normal Play

You can play up to five CDs in a row.

?/1

(Power)

. >

CD NX

Multi stick PUSH ENTER

MODE SELECT

1 Press one of the A 1~5 buttons and

place a CD on the disc tray.

If a disc is not placed properly, it will not be recognized.

Place with the label side up. When you play a CD single (8 cm CD), place it on the inner circle of the tray.

Press the same button to close the disc tray. To insert other CDs, press A of other numbers to open the disc tray.

The CD presence indicator lights in the display.

Disc presence indicator

2 Press one of the DISC 1~5 buttons.

The disc tray closes and play starts. If you press CD NX (or CD H on the

remote) when the disc tray is closed, playback starts from the CD loaded on the tray whose disc pointer indicator lights.

Basic Operations

h H

MmX

VOLUME

D.SKIP CD H

. > x X

m M

ENTER

B/b

VOLUME +/–

m M

Disc number

CD indicators

Disc presence indicator

In “1 Disc” play mode (see page 14)

Track number

Playing time

In “All Discs” play mode (see page 14)

Disc pointor indicator

continued

Playing a CD (continued)

Stop play Pause

Select a track

Find a point in a track

Select a CD in stop mode

Play only the CD you have selected

Play all CDs

Remove a CD Exchange other

CDs while playing

Adjust the volume

Do this

Press x. Press CD NX (or X on the

remote). Press again to resume play.

During play or pause, press > (to go forward) or . (to go back).

Press and hold down M or m during play and release it at the desired point.

Press one of the DISC 1~5 buttons (or D.SKIP on the remote).

1 Press MODE SELECT

repeatedly to select “Set Up Mode”, then press PUSH ENTER.

2 Move the multi stick toward b or

B repeatedly to select “CD Set Up ?”, then press PUSH ENTER.

3 Move the multi stick toward b or

B repeatedly to select “Play Mode Set Up ?”, then press PUSH ENTER.

4 Move the multi stick toward b or

B repeatedly to select “Play Mode 1 Disc”, then press PUSH ENTER.

1 Press MODE SELECT repeatedly

to select “Set Up Mode”, then press PUSH ENTER.

2 Move the multi stick toward b or

B repeatedly to select “CD Set Up ?”, then press PUSH ENTER.

3 Move the multi stick toward b or

B repeatedly to select “Play Mode Set Up ?”, then press PUSH ENTER.

4 Move the multi stick toward b or

B repeatedly to select “Play Mode All Discs”, then press

PUSH ENTER. Press one of the A 1~5 buttons. Press one of the A 1~5 buttons

to open the tray that contains the CD that you want to change. When you change the CD, press the same button to close the tray.

Turn VOLUME (or press VOLUME +/– on the remote).

Tips

• Pressing CD NX when the power is off automatically turns the power on and starts CD playback if there is a CD in the tray (One Touch Play). When the system is in the Power Saving Mode, the One Touch Play function does not work.

• You can switch from another source to the CD player and start playing a CD just by pressing CD NX or one of the DISC 1~5 buttons (Automatic Source Selection).

• If there is no CD in the player, “No Disc” appears in the display.

• When a disc tray is holding a CD, the indicator for the tray lights orange. In the display, when a disc tray holding a CD is selected (or the CD in the disc tray is playing), the disc pointer indicator lights. When a disc tray holding a CD is not selected, the disc presence indicator lights, but the disc pointer indicator does not light. When all disc trays are empty, all the disc pointer indicators and all the disc presence indicators light.

Note

When a tray has not been read by the unit, the disc presence indicator may light even though there is no disc on the tray.

Recording a CD

— CD Synchro Recording

The CD SYNC button lets you record from a CD to a tape easily. You can use TYPE I (normal) or TYPE II (CrO2) tapes. The recording level is adjusted automatically.

TAPE B N Indicator

?/1

(Power)

TAPE B n

Multi stick PUSH ENTER

2 Press one of the A 1~5 buttons and

place a CD on the disc tray.

Press the same button to close the disc tray. If the indicator for the tray you want to

record is not lit, press D.SKIP on the remote repeatedly until it lights.

Place with the label side up. When you play a CD single (8 cm CD), place it on the inner circle of the tray.

3 Press CD SYNC.

Deck B stands by for recording and the CD player stands by for playback. The TAPE B N indicator (for the front side) lights and the REC PAUSE/START button flashes.

4 Press MODE SELECT repeatedly to

select “Set Up Mode”, then press PUSH ENTER.

5 Move the multi stick toward b or B

repeatedly to select “TAPE Set Up ?”, then press PUSH ENTER.

Basic Operations

18, REC PAUSE/START

1 Press A B and insert a recordable tape

into deck B.

Insert with the side you want to record facing forward.

6 Move the multi stick toward b or B

repeatedly to select “Direction Set Up ?”, then press PUSH ENTER.

7 Move the multi stick toward b or B

repeatedly to select “1 Way” to record on one side, or “Cycle” (or “Relay”) to record on both sides, then press PUSH ENTER.

8 Press REC PAUSE/START.

Recording starts.

continued

Recording a CD (continued)

To stop recording

Press x.

To cancel the menu operation

Press MODE SELECT.

Tips

• If you want to record from the reverse side, press TAPE B n to light its indicator after pressing CD SYNC.

• When you record on both sides, be sure to start from the front side. If you start from the reverse side, recording stops at the end of the reverse side.

• When you want to reduce the hiss noise in low-level high-frequency signals, do the following procedure after pressing CD SYNC. 1 Press MODE SELECT repeatedly to select “Set

Up Mode”, then press PUSH ENTER.

2 Move the multi stick toward b or B repeatedly

to select “TAPE Set Up ?”, then press PUSH ENTER.

3 Move the multi stick toward b or B repeatedly

to select “DOLBY NR Set Up ?”, then press PUSH ENTER.

4 Move the multi stick toward b or B repeatedly

to select “On”, then press PUSH ENTER.

“DOLBY NR” appears in the display. To return to the original setting, repeat steps 1 through 4 and select “Off” in step 4.

Note

You cannot listen to other sources while recording.

Listening to the radio

— Preset Tuning

Preset radio stations in the tuner’s memory first (see “Step 4: Presetting radio stations” on page

10).

?/1

(Power)

m M

MODE

SELECT

VOLUME

Multi stick

PUSH ENTER

TUNER/BAND

Turn off the radio Adjust the volume

Do this

Press ?/1. Turn VOLUME (or press

VOLUME +/– on the remote).

h H

MmX

. >

m M

VOLUME +/–

1 Press TUNER/BAND repeatedly to

select FM or AM.

2 Press . or > repeatedly to tune in

the desired preset station.

Preset number*

STEREO

To listen to non-preset radio stations

Use manual or automatic tuning in step 2. For manual tuning, press m or M repeatedly. For automatic tuning, press and hold m or M.

Tips

• Pressing TUNER/BAND when the power is off automatically turns the power on and tunes to the last received station (One Touch Play). When the system is in the Power Saving Mode, the One Touch Play function does not work.

• You can switch from another source to the radio just by pressing TUNER/BAND (Automatic Source Selection).

• When an FM program is noisy, do the following procedure: 1 Press MODE SELECT repeatedly to select “Set

Up Mode”, then press PUSH ENTER.

2 Move the multi stick toward b or B repeatedly

to select “TUNER Set Up ?”, then press PUSH ENTER.

3 Move the multi stick toward b or B repeatedly

to select “Stereo Mono ?”, then press PUSH ENTER.

4 Move the multi stick toward b or B repeatedly

to select “Mono”, then press PUSH ENTER.

“Mono” appears in the display. There will be no stereo effect, but the reception will improve. To restore the stereo effect, repeat steps 1 through 4 and select “Stereo” in step 4.

• To improve broadcast reception, reorient the respective antenna.

Basic Operations

Frequency

* When only one station is preset, “ONE PRESET”

appears in the display.

Recording from the radio

You can record the radio program on a tape by calling up a preset station. You can use TYPE I (normal) or TYPE II (CrO2) tapes. The recording level is automatically adjusted.

3 Press A B and insert a recordable tape

into deck B.

Insert with the side you want to record facing forward.

?/1

(Power)

TAPE B n

4,9

Multi stick

PUSH ENTER

1 Press TUNER/BAND to select FM or

AM.

2 Press . or > repeatedly to tune in

a preset station.

Preset number

4 Press REC PAUSE/START.

Deck B stands by for recording.

5 Press MODE SELECT repeatedly to

select “Set Up Mode”, then press PUSH ENTER.

6 Move the multi stick toward b or B

repeatedly to select “TAPE Set Up ?”, then press PUSH ENTER.

7 Move the multi stick toward b or B

repeatedly to select “Direction Set Up ?”, then press PUSH ENTER.

8 Move the multi stick toward b or B

repeatedly to select “1 Way” to record on one side, or “Cycle” (or “Relay”) to record on both sides, then press PUSH ENTER.

9 Press REC PAUSE/START.

Recording starts.

To stop recording

Press x.

To cancel the menu operation

Press MODE SELECT.

STEREO

Frequency

Tips

• If you want to record from the reverse side, press TAPE B n to light its indicator after pressing REC PAUSE/START in step 4.

• When you record on both sides, be sure to start from the front side. If you start from the reverse side, recording stops at the end of the reverse side.

• To record non-preset stations, use m and M in step 2 to tune in the desired station manually.

• When you want to reduce the hiss noise in lowlevel high-frequency signals, do the following procedure after pressing REC PAUSE/START in step 4. 1 Press MODE SELECT repeatedly to select “Set

Up Mode”, then press PUSH ENTER.

2 Move the multi stick toward b or B repeatedly

to select “TAPE Set Up ?”, then press PUSH ENTER.

3 Move the multi stick toward b or B repeatedly

to select “DOLBY NR Set Up ?”, then press PUSH ENTER.

4 Move the multi stick toward b or B repeatedly

to select “On”, then press PUSH ENTER.

“DOLBY NR” appears in the display. To return to the original setting, repeat steps 1 through 4 and select “Off” in step 4.

• If noise is heard while recording from the radio, move the respective antenna to reduce the noise.

Playing a tape

You can use any type of tape, TYPE I (normal), TYPE II (CrO2) or TYPE IV (metal), since the deck automatically detects the tape type. You can also use . and > to quickly search for songs you want to hear.

?/1

(Power)

Multi stick PUSH ENTER

Basic Operations

VOLUMExm M. >

continued

Playing a tape (continued)

4 Move the multi stick toward b or B

repeatedly to select “TAPE Set Up ?”, then press PUSH ENTER.

TAPE A h H TAPE B h H

. > x m M

MODE SELECT ENTER

B/b

VOLUME +/–

h H

MmX

1 Press A A or A B and insert a recorded

tape in deck A or B.

Insert with the side you want to play facing forward.

Tape presence indicator lights in the display.

Tape presence indicator

5 Move the multi stick toward b or B

repeatedly to select “Direction Set Up ?”, then press PUSH ENTER.

6 Move the multi stick toward b or B

repeatedly to select “1 Way” to play one side, “Cycle” to play both sides, or “Relay”* to play both decks in succession, then press PUSH ENTER.

7 Press TAPE A (or TAPE B) N.

Press TAPE A (or TAPE B) n to play the reverse side. The tape starts playing.

When using the remote, press TAPE A (or TAPE B) hH to start playback. To play reverse side, press TAPE A (or TAPE B) hH again.

* Relay play always follows the following sequence:

Deck A (front side) tDeck A (reverse side) Deck B (reverse side)

Stop play Fast-forward Rewind Remove the cassette Adjust the volume

* This tape deck does not have play pause function.

You cannot use X to pause tape playback.

To cancel the menu operation

Press MODE SELECT.

Deck B (front side)

Do this

Press x. Press m or M. Press m or M. Press A A or A B. Turn VOLUME (or press

VOLUME +/– on the remote).

2 Press FUNCTION repeatedly to select

“TAPE A” or “TAPE B”.

3 Press MODE SELECT repeatedly to

select “Set Up Mode”, then press PUSH ENTER.

+ 44 hidden pages