Sony KV-SW21M80, KV-SW21M83, KV-BZ21M80 User Manual

0 (0)

Trinitron Color TV

KV-SW21

KV-BZ21

2-652-924-11 (1)

Operating Instructions

• Before operating the unit, please read this manual thoroughly and retain

it for future reference.

M83

M80

110-240 V AC, 50/60 Hz

Indicated on the rear of the TV

B/G, I, D/K, M

PAL, PAL 60, SECAM, NTSC3.58, NTSC4.43

VHF : E2 to E12 /UHF : E21 to E69 /

CATV : S01 to S03, S1 to S41

UHF : B21 to B68 /CATV : S01 to S03, S1 to S41

VHF : C1 to C12, R1 to R12 /

UHF : C13 to C57, R21 to R60 /

CATV : S01 to S03, S1 to S41, Z1 to Z39

VHF : A2 to A13 /UHF : A14 to A79 /

CATV : A-8 to A-2, A to W+4, W+6 to W+84

75-ohm external terminal

4 W + 4 W 5 W + 5 W 3 W + 3 W

12 W ––

Input: 2 Output: 1 Phono jacks; 1 Vp-p, 75 ohms

Input: 3 Output: 1 Phono jacks; 500 mVrms

Input: 1 Phono jacks;

Y: 1 Vp-p, 75 ohms,

sync negative

B: 0.7 Vp-p, 75 ohms

R: 0.7 Vp-p, 75 ohms

Output: 1 Stereo minijack

21 in.

Measured diagonally

647 × 533 × 530 647 × 469 × 509 497 × 468 × 494

29 25 23

A Specifications

KV-SW21M83

Note

KV-SW21M80

KV-BZ21M80

Design and specifications are subject to change without notice.

Power requirements

Power consumption (W)

Television system

Color system

Channel coverage

B/G

D/K

8 (Antenna)

Audio output (Speaker)

3D Woofer

Number of terminal

(Video)

(Audio)

(Component

Video)

i (Headphone)

Picture tube

Tube size (cm)

Screen size (cm)

Dimensions (w/h/d, mm)

Mass (kg)

Clean the TV with a dry and soft

cloth. Do not use benzine, thinner,

or any other chemicals to clean the

TV. Do not attach anything (e.g.,

adhesive tape, cellophane tape,

glue) on the painted cabinet of the

TV. Do not scratch the picture

tube.

B WARNING

• Dangerously high voltages are present inside the TV.

• TV operating voltage: 110 – 240 V AC.

• Do not plug in the power cord until you have completed making all other

connections; otherwise a minimum leakage current might flow through the antenna

and other terminals to ground.

• To avoid battery leakage and damage to the remote, remove the batteries from the

remote if you are not going to use it for several days. If any liquid leaks from the

batteries and touches your skin, immediately wash it away with water.

Install the TV on a stable TV stand

and floor which can support the

TV set weight. Ensure that the TV

stand surface is flat and its area is

larger than the bottom area of the

TV.

Do not plug in too many

appliances to the same power

socket. Do not damage the power

cord.

For children’s safety, do not leave

children alone with the TV. Do not

allow children to climb onto it.

For your own safety, do not touch

any part of the TV, the power cord

and the antenna cable during

lightning storms.

Do not place any objects on the TV.

The apparatus shall not be

exposed to dripping or splashing

and that no objects filled with

liquids, such as vases, shall be

placed on the apparatus.

Do not operate the TV if any liquid

or solid object falls into it. Have it

checked immediately by qualified

personnel only.

Do not block the ventilation

openings of the TV. Do not install

the TV in a confined space, such

as a bookcase or built-in cabinet.

Do not open the cabinet and the

rear cover of the TV as high

voltages and other hazards are

present inside the TV. Refer

servicing and disposal of the TV

to qualified personnel.

Pull the power cord out by the

plug. Do not pull the power cord

itself. Even if your TV is turned

off, it is still connected to the AC

power source (mains) as long as

the power cord is plugged in.

Unplug the TV before moving it

or if you are not going to use it for

several days.

To prevent fire or shock hazard, do

not expose the TV to rain or

moisture.

Your TV is recommended for

home use only. Do not use the TV

in any vehicle or where it may be

subject to excessive dust, heat,

moisture or vibrations.

C Securing the TV

To prevent the TV from falling, use the supplied screws, clamps and band to

secure the TV. Use only the supplied screws. Use of other screws may damage

the TV.

Screw the band to the TV stand and

to the provided hole at the rear of

your TV.

(1)

Put a cord or chain through the

clamps.

(2)

Screw one clamp to a wall or

pillar and the other clamp to the

provided hole at the rear of your TV.

20 mm

3.8 mm

screws

clamps band

End

Select

Confirm

Initial Setup

Language:

English

Insert the batteries (supplied) into the remote.

Note

•Do not use old or different types of batteries together.

Connect the antenna cable (not supplied) to 8

(antenna input) at the rear of the TV.

Tip

•You can also connect your TV to other optional components (see H).

Plug in the power cord, then press ! on the TV to turn it on.

Note

•The 1 (standby) indicator flashes green for a few seconds when

turning on the TV. This does not indicate a malfunction.

Set up the TV by following the instructions of the “Initial

Setup” menu (see E).

D Getting Started

Step 1

Step 2

Step 3

Step 4

Program Sorting/Edit

Off

Sorting mode

PROG

SkipLabel

Off01

Exit

Select

Confirm

Program Sorting/Edit

Off

Sorting:

Edit:

PROG

SkipLabel

Exit

Select

Confirm

End

Select

Confirm

Initial Setup

Language:

English

Start Auto Program now?

Yes

First please connect

cable/ antenna

Initial Setup

End

Select

Confirm

Program:

Auto Program

TV System: Auto

VHF Low

End

Setting up your TV (“Initial Setup”)

When you turn on your TV for the first time, the “Initial Setup” menu will

appear. You may change the menu language, preset the TV channels

automatically and sort or edit the channels using the buttons on the remote

control or TV top control panel.

Press V or v to select the desired menu

language, then press

The selected menu language appears.

Press V or v to select “Yes”, then press to

preset the channels automatically.

The screen will indicate automatic

presetting is in progress.

After all available channels have been tuned

and stored, the “Program Sorting/Edit”

menu appears automatically on the screen.

To skip automatic channel presetting, select

“No”, then press

If the message “No channel found. Please

connect cable/antenna” appears, check your

TV connections, then press .

The “Program Sorting/Edit” menu enables

you to sort and edit the channels.

a) If you wish to keep the channels in the current

condition, press WEGA GATE to exit.

b) Press V or v to select the program

number with the channel you wish to

change. The selected channel will appear

on the screen.

c) If you wish to store the channels in a

different order:

1) Press b to enter sorting mode.

2) Press V or v to select the new program

number position for your selected

channel, then press B.

d) If you wish to edit the channels, press

to change to edit mode.

Press b until the mode that you wish to edit

is highlighted: Label, Skip,

(block symbol).

Then press

1) To label, press V or v to select the

alphanumeric characters for the label.

Then press

2) To skip the program number, press V or v to

select “On”. Then press

You can skip this program number when

using PROG +/-.

3) To block unwanted program number,

press V or v to select

. Then press .

e) Repeat step b) to d) if you wish to change other

channels.

Press WEGA GATE to go to the next menu.

To prevent this “Initial Setup” menu from

appearing again when you turn on the TV

by pressing !, press V or v to select “No”,

then press

To allow this menu to appear again, select

“Yes”, then press

Tip

• You can immediately go to the end of the ”Initial Setup” menu by pressing WEGA GATE.

Select

Confirm

Initial Setup

Display this menu next time?

Yes

Exit

Select

Confirm

Program Sorting/Edit

Off

Edit mode

PROG

SkipLabel

Exit

Select

Confirm

Program Sorting/Edit

Off

Edit mode

PROG

SkipLabel

Exit

Select

Confirm

Program Sorting/Edit

Off

Edit mode

PROG

SkipLabel

Setting up your TV (“Initial Setup”) (continued)

(MONO)

WEGA GATE

PROG

SOUND MODE

123

(MONO) (MONO)

qsqd

(MONO)

TV front panel

TV rear panel

F TV top control, front and rear

panels

TV top control panel

Button/Terminal Function See

1 ! Turn off or turn on the TV. D

2 Remote control sensor. -

3 Wake Up indicator. J

3 1 Standby indicator. D

4 i Headphone jack. -

5 t2 Video input terminal 2. H

6 PROG +/– Select program number. -

7 2 +/– Adjust volume. -

8 t Select TV or video input. H

WEGA GATE menu operations

6,7 V,v,B,b Select and adjust items. K

Confirm selected items. K

9 WEGA GATE Display or cancel WEGA GATE menu. K

0 SOUND MODE Select sound mode options with a 5-Band Graphic J

Equalizer display.

qa 8 Antenna input terminal. H

qs T Monitor output terminal. H

qd Component video input terminal. H

qf t1 Video input terminal 1. H

qg WOOFER 3D WOOFER terminal. G

(KV-SW21M83 only)

+ 14 hidden pages