Page 1
KLV-32W400A/40W400A/46W400A/52W400A
E Model
SERVICE MANUAL
India Model
Indonesia Model
Middle East Model
Thailand Model
Philippines Model
Saudi Arabia Model
South Africa Model
RM-GA011 KLV-32W400A/40W400A/46W400A/52W400A
EX1 CHASSIS
LCD Colour TV
Page 2
SPECIFICATIONS
KLV-32/40/46/52W400A (GA) 2
Page 3
KLV-32/40/46/52W400A (GA) 3
Page 4
WARNINGS AND CAUTIONS SAFETY-RELATED COMPONENT
CAUTION
These servicing instructions are for use by qualified service
personnel only.
To reduce the risk of electric shock, do not perform any servicing
other than that contained in the operating instructions unless you
are qualified to do so.
WARNING!!
WARNING
It is essential that all critical parts be replaced only with the part
number specified in the electrical parts list to prevent electric
shock, fire, or other hazard.
NOTE: Do not modify the original design without obtaining
written permission from the manufacturer or you will
void the original parts and labor guarantee.
An isolation transformer should be used during any service to
avoid possible shock hazard, because of live chassis.
The chassis of this receiver is directly connected to the ac power
line.
! SAFETY-RELATED COMPONENT
WARNING!!
Replace all components with Sony parts whose part numbers
appear as shown in this manual or in supplements
published by Sony.
USE CAUTION WHEN HANDLING THE LCD PANEL
When repairing the LCD panel, be sure you are grounded by
using a wrist band.
When repairing the LCD panel on the wall, the LCD panel must
be secured using the 4 mounting holes on the rear cover.
1) Do not press on the panel or frame edge to avoid the risk of
electric shock.
2) Do not scratch or press on the panel with any sharp objects.
3) Do not leave the module in high temperatures or in areas of
high humidity for an extended period of time.
4) Do not expose the LCD panel to direct sunlight.
5) Avoid contact with water. It may cause a short circuit within
the module.
6) Disconnect the AC power when replacing the backlight (CCFL)
or inverter circuit.
(High voltage occurs at the inverter circuit at 650Vrms.)
7) Always clean the LCD panel with a soft cloth material.
8) Use care when handling the wires or connectors of the inverter
circuit. Damaging the wires may cause a short.
9) Protect the panel from ESD to avoid damaging the electronic
circuit (C-MOS).
KLV-32/40/46/52W400A (GA) 4
Page 5
SAFETY CHECK-OUT
l
t
µ
d
AC
)
t
Col
pe
.
After correcting the original service problem, perform the
following safety checks before releasing the set to the customer:
1. Check the area of your repair for unsoldered or poorly
soldered connections. Check the entire board surface for
solder splashes and bridges.
2. Check the interboard wiring to ensure that no wires are
“pinched” or touching high-wattage resistors.
3. Check that all control knobs, shields, covers, ground straps,
and mounting hardware have been replaced. Be absolutely
certain that you have replaced all the insulators.
4. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
5. Look for parts which, though functioning, show obvious
signs of deterioration. Point them out to the customer and
recommend their replacement.
6. Check the line cords for cracks and abrasion. Recommend
the replacement of any such line cord to the customer.
7. Check the antenna terminals, metal trim, “metallized”
knobs, screws, and all other exposed metal parts for AC
leakage. Check leakage as described below.
Leakage Test
The AC leakage from any exposed metal part to earth ground
and from all exposed metal parts to any exposed metal part
having a return to chassis, must not exceed 0.5 mA (500
microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or
RCA WT-540A. Follow the manufacturers’ instructions to
use these instructions.
2. A battery-operated AC milliampmeter. The Data Precision
245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit”
indication is 0.75 V, so analog meters must have an accurate
low voltage scale.
The Simpson’s 250 and Sanwa SH-63TRD are examples of
passive VOMs that are suitable. Nearly all battery-operated
digital multimeters that have a 2 VAC range are suitable (see
Figure A).
How to Find a Good Earth Ground
A cold-water pipe is a guaranteed earth ground; the cover-plate
retaining screw on most AC outlet boxes is also at earth ground.
If the retaining screw is to be used as your earth ground, verify
that it is at ground by measuring the resistance between it and a
cold-water pipe with an ohmmeter. The reading should be zero
ohms.
If a cold-water pipe is not accessible, connect a 60- to 100-watt
trouble- light (not a neon lamp) between the hot side of the
receptacle and the retaining screw. Try both slots, if necessary,
to locate the hot side on the line; the lamp should light at normal
brilliance if the screw is at ground potential (see Figure B).
Exposed Meta
Parts on Se
ouble Ligh
AC Outlet Box
.15
0.75V
Earth Groun
Ohmmeter
FigureA. Using an AC voltmeter to check AC leakage. Figure B. Checking for earth ground
d-water Pi
KLV-32/40/46/52W400A (GA) 5
Page 6
SELF DIAGNOSIS FUNCTION
The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY LED will automatically begin to flash.
The number of times the LED flashes translates to a probable source of the problem.
A definition of the STANDBY LED flash indicators is listed in the instruction manual for the user’s knowledge and reference.
If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to
reveal past problems and how often these problems occur.
1-1. DIAGNOSTIC TEST INDICATORS
When an error occurs, the STANDBY LED will flash a set number of times to indicate the possible cause of the problem.
If there is more than one error, the LED will identify the first of the problem areas.
Result for all of the following diagnostic items are displayed on screen.
If the screen displays a “0”, no error has occurred .
Number of times STANDY LED Monitoring Items
(Red) flashes (Screen Display)
2 times DC_DET Main power supply voltage error (12V, etc)
3 times DC_ALERT1 Malfunction of 3.3V line (Trident circuit, etc)
4 times DC_ALERT2 Malfunction of 5V line
(Voltage Supply to FE, etc)
5 times DC_ALERT3 Malfunction of power supply for screen
6 times BACKLIGHT Malfunction of inverter or overcurrent, etc
7 times TEMPERATURE Abnormal temperature inside unit
8 times AUDIO Audio circuit error (amplifier, etc.)
10 times DEF Digital FE circuit error
11 times B-ENGINE Malfunction of Trident IC or around IC
12 times HFR BH board error
13 times (No item on screen display) Malfunction of balancer
Diagnostic Item Description
1-2. DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT
[ FLASH COUNT ]
2 times
4 times
5 times
LED ON 0.3 sec.
LED OFF 0.3 sec.
Note: One flash counts is not self-diagnostic.
STANDBY LED
LED OFF
2 sec.
1-3. STOPPING THE STANDBY FLASH
Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY LED from flashing.
KLV-32/40/46/52W400A (GA) 6
Page 7
1-4. SELF-DIAGNOSTIC SCREEN DISPLAY
DC_DET
DC_ALEAT1
DC_ALERT2
DC_ALERT3
BACKLIGHT
TEMPERATURE
AUDIO
DFE
B-ENGINE
HFR
0
0
0
0
0
0
0
0
0
0
TV
Monitoring Items
Error Count Record
For details, refer to "1-1. DIAGNOSTIC TEST INDICATORS"
[ SELF-DIAGNOSTIC SCREEN DISPLAY ]
Number "0": means that no fault detected.
Number "1": means a fault was detected one time only.
For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it is possible to
bring up past occurrences of failure for confirmation on the screen:
1-4-1. To Bring Up Screen Test
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
5
( Info/Text reveal )
( Number button )
* ( Volume )
( TV standby )
* : Note that this differs from entering the service mode (volume +)
Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen
After you have completed the repairs, clear the result display to “0”.
1-5. Quitting Self-diagnostic screen
To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.
KLV-32/40/46/52W400A (GA) 7
Page 8
TABLE OF CONTENTS
SAFETY CHECK-OUT ............................................. 5
SELF DIAGNOSIS FUNCTION ................................ 6
1. DISASSEMBLY ............................................... 1-1
1-1. KLV-32W400A ...................................................... 1-1
1-1-1. REAR COVER AND STAND ASSY
REMOVAL ...................................................... 1-1
1-1-2. SWITCH UNIT AND SIDE JACK BRACKET
REMOVAL ...................................................... 1-2
1-1-3. UNDER COVER AND VESA FRAME (TOP)
REMOVAL ...................................................... 1-3
1-1-4. BG1G BOARD REMOVAL ........................... 1-4
1-1-5. POWER UNIT REMOVAL ............................ 1-5
1-1-6. SPEAKER AND UNDER BAR REMOVAL . 1-6
1-1-7. LCD PANEL, H3E BOARD AND H4 BOARD
REMOVAL ...................................................... 1-7
1-1-8. WIRING LAYOUT ......................................... 1-8
1-2. KLV-40W400A ...................................................... 1-9
1-2-1. REAR COVER AND STAND ASSY
REMOVAL ...................................................... 1-9
1-2-2. AC INLET AND UNDER COVER
REMOVAL .................................................... 1-10
1-2-3. BG1G BOARD AND IP5 BOARD
REMOVAL .................................................... 1-11
1-2-4. FRAME REMOVAL ..................................... 1-12
1-2-5. SPEAKER (L) REMOVAL ........................... 1-13
1-2-6. SPEAKER (R) REMOVAL ........................... 1-13
1-2-7. LCD PANEL, H3E BOARD AND H4 BOARD
REMOVAL .................................................... 1-14
1-2-8. WIRING LAYOUT ....................................... 1-15
1-3. KLV-46W400A .................................................... 1-16
1-3-1. REAR COVER AND STAND ASSY
REMOVAL .................................................... 1-16
1-3-2. AC INLET AND UNDER COVER
REMOVAL .................................................... 1-17
1-3-3. BG1G BOARD AND IP5 BOARD
REMOVAL .................................................... 1-18
1-3-4. FRAME REMOVAL ..................................... 1-19
1-3-5. SPEAKER (L) REMOVAL ........................... 1-20
1-3-6. SPEAKER (R) REMOVAL ........................... 1-20
1-3-7. LCD PANEL, H3E BOARD AND
H4 BOARD REMOVAL ............................... 1-21
1-3-8. WIRING LAYOUT ....................................... 1-22
1-4. KLV-52W400A .................................................... 1-23
1-4-1. REAR COVER AND STAND ASSY
REMOVAL .................................................... 1-23
1-4-2. AC INLET AND UNDER COVER
REMOVAL .................................................... 1-24
1-4-3. D4, D5, G5 AND BG1B BOARDS
REMOVAL .................................................... 1-25
1-4-4. FRAME REMOVAL ..................................... 1-26
1-4-5. SPEAKER (L) REMOVAL ........................... 1-27
1-4-6. SPEAKER (R) ................................................ 1-27
1-4-7. LCD PANEL, H3E BOARD AND H4 BOARD
REMOVAL .................................................... 1-28
1-4-8. WIRING LAYOUT ....................................... 1-29
2. DIAGRAMS ..................................................... 2-1
2-1. CIRCUIT BOARDS LOCATION ......................... 2-1
(1) KLV-32W400A................................................ 2-1
(2) KLV-40W400A................................................ 2-1
(3) KLV-46W400A................................................ 2-1
(4) KLV-52W400A................................................ 2-1
2-2. BLOCK DIAGRAM .............................................. 2-2
(1) BG1G Board ..................................................... 2-2
3. EXPLODED VIEWS ........................................ 3-1
3-1. KLV-32W400A ...................................................... 3-2
3-1-1. REAR COVER AND STAND ASSY ............. 3-2
3-1-2. CHASSIS-1 ...................................................... 3-3
3-1-3. CHASSIS-2 ...................................................... 3-4
3-2. KLV-40W400A ...................................................... 3-5
3-2-1. REAR COVER AND STAND ASSY ............. 3-5
3-2-2. CHASSIS-1 ...................................................... 3-6
3-2-3. CHASSIS-2 ...................................................... 3-7
3-3. KLV-46W400A ...................................................... 3-8
3-3-1. REAR COVER AND STAND ASSY ............. 3-8
3-3-2. CHASSIS-1 ...................................................... 3-9
3-3-3. CHASSIS-2 .................................................... 3-10
3-4. KLV-52W400A .................................................... 3-11
3-4-1. REAR COVER AND STAND ASSY ........... 3-11
3-4-2. CHASSIS-1 .................................................... 3-12
3-4-3. CHASSIS-2 .................................................... 3-13
3-5. PACKING MATERIALS .................................... 3-14
3-5-1. KLV-32W400A.............................................. 3-14
3-5-2. KLV-40W400A.............................................. 3-15
3-5-3. KLV-46W400A.............................................. 3-16
3-5-4. KLV-52W400A.............................................. 3-17
KLV-32/40/46/52W400A (GA) 8
Page 9
SECTION 1
DISASSEMBLY
1-1. KLV-32W400A
1-1-1. REAR COVER AND STAND ASSY REMOVAL
5 Two screws
(+BV 3X12,
TYPE2, IT-3)
3 Seven screws
(+BVTP2 4X16)
4 One screws
(+PSW M5X8)
3 Three screws
(+BVTP2 4X16)
1 Three screws
(+PSW M5X16)
2 Stand assy
3 Eight screws
(+BVTP2 4X16)
6 Rear cover assy
KLV-32/40/46/52W400A (GA) 1-1
Page 10
KLV-32W400A
1-1-2. SWITCH UNIT AND SIDE JACK BRACKET REMOVAL
2 Side jack
bracket assy
Claw
Claw
1 Switch unit
KLV-32/40/46/52W400A (GA) 1-2
Page 11
KLV-32W400A
1-1-3. UNDER COVER AND VESA FRAME (TOP) REMOVAL
5 VESA frame
(TOP)
4 Two screws
(+PSW M4X8)
3 Under cover
2 Two screws
(+BVST 3X8)
1 Power supply
cord
KLV-32/40/46/52W400A (GA) 1-3
Page 12
KLV-32W400A
1-1-4. BG1G BOARD REMOVAL
5 Four screws
(+BVST 3X8)
6 One screw
(+BVST 3X8)
q; Main bracket assy
3 One screw
(+BVST 3X8)
1 Four screws
(+PSW M3x5)
2 Two screws
(SP 4-4O UNC)
4 B (J) shield
5 Five screws
(+BVST 3X8)
8 BG1G board
9 Two screws
(+BVST 3X8)
7 Harness with connector
(LVDS)
KLV-32/40/46/52W400A (GA) 1-4
Page 13
KLV-32W400A
1-1-5. POWER UNIT REMOVAL
1 One screw
(+PSW M4X8)
5 Two screws
(+PSW 3SG)
6 Power unit
7 G1 brackt
Claw
2 VESA frame
(BOTTOM)
5 Two screws
(+PSW 3SG)
3 One screw
(+PSW M4X8)
4 VESA frame
(BOTTOM)
KLV-32/40/46/52W400A (GA) 1-5
Page 14
KLV-32W400A
1-1-6. SPEAKER AND UNDER BAR REMOVAL
3 Loudspeaker
1 Two screw
(+BVTP2 4X16)
2 Under bar
4 Loudspeaker
KLV-32/40/46/52W400A (GA) 1-6
Page 15
KLV-32W400A
1-1-7. LCD PANEL, H3E BOARD AND H4 BOARD REMOVAL
1 One screw
(+BVTP2 4X16)
2 Two screws
(+PSW M4X8)
4 One screw
(+BVTP2 4X16)
3 Spine frame (L)assy
7 two screws
(+PSW M4X8)
5 Three screws
(+PSW M4X8)
6 Spine frame (R)assy
8 Two screws
(+BVTP2 4X16)
7 Two screws
(+PSW M4X8)
9 Vesa frame assy
q; One screw
(+BVTP 3X12 TYPE2 IT-3)
qa H4 board
Claw
qs Light guide
qd H3E board
qf Claer panel
qh Two screws
(+BVTP2 4X16)
qj LCD panel
qg Illumination module
qk Bezel assy
KLV-32/40/46/52W400A (GA) 1-7
Page 16
KLV-32W400A
1-1-8. WIRING LAYOUT
CN001
SWITCH Unit
Inverter
Speaker (L)
CN401
CN301
Power
cord
H4 board
H3E board
Power Unit
CN601
CN602
Illumination
module
CN4001
CN5501
CN5500
CN3004
CN2001
CN4000
CN8001
BG1G board
CN3003
Speaker (R)
KLV-32/40/46/52W400A (GA) 1-8
Page 17
1-2. KLV-40W400A
1-2-1. REAR COVER AND STAND ASSY REMOVAL
4 Two screws
(+PSW M5X8)
3 Six screws
(+BVTP2 4X16)
4 Two screws
(+PSW M5X8)
6 Two screws
(+BV 3X12,
TYPE2, IT-3)
3 Five screws
(+BVTP2 4X16)
7 Rear cover assy
3 Two screws
(+BVTP2 4X16)
5Two screws
(+PSW M5X12)
3 Four screws
(+BVTP2 4X16)
3 Two screws
(+BVTP2 4X16)
1 Three screws
(+PSW M5X12)
2 Stand assy
8 Switch unit
KLV-32/40/46/52W400A (GA) 1-9
Page 18
KLV-40W400A
1-2-2. AC INLET AND UNDER COVER REMOVAL
7 Two screws
(+BVST 3X8)
8 AC inlet bracket
6 AC inlet
4 Under cover (L2)
2 Under bar (L)
1 Two screws
(+BVTP2 4X16)
5 Two screws
(+KTT 3X10(S TYPE))
3 One screw
(+BVST 3X8)
KLV-32/40/46/52W400A (GA) 1-10
Page 19
KLV-40W400A
1-2-3. BG1G BOARD AND IP5 BOARD REMOVAL
3 Two screws
(+BVST 3X8)
4 B(G)shild
5 Side jack
bracket assy
6 MS cover
qa Two screws
(+BVST 3X8)
0 Harness with
connector(LVDS)
qs G5 frame
7 Four screws
(+BVST 3X8)
9 One screws
(+BVST 3X8)
8 BG1G board
7 Five screws
(+BVST 3X8)
1 Three screws
(+BVST 3X8)
qa Two screws
(+BVST 3X8)
2 IP5 board
1 Three screws
(+BVST 3X8)
KLV-32/40/46/52W400A (GA) 1-11
Page 20
KLV-40W400A
qh Bottom frame
assy
7 Spine frame assy
qf Spine frame assy
1 Two screws
(+PSW M5X8)
5 Two screws
(+PSW M4X8)
qs Two screws
(+PSW M4X8)
6 One screw
(+PSW M4X8)
8 Two screws
(+PSW M5X8)
4 Vesa frame (BTM) assy
qa Vesa frame (BTM)
assy
2 Vesa frame (TOP)
9 Vesa frame
(TOP)
3 Two screws (+PSW M5X8)
0 Two screws (+PSW M5X8)
qg Four screws
(+BVTP2 4X16)
qd One screw
(+PSW M4X8)
1-2-4. FRAME REMOVAL
KLV-32/40/46/52W400A (GA) 1-12
Page 21
KLV-40W400A
1-2-5. SPEAKER (L) REMOVAL
1 Loudspeaker
2 Speaker cushion
Both
Both
1-2-6. SPEAKER (R) REMOVAL
1 Loudspeaker
Both
2 Speaker cushion
Both
KLV-32/40/46/52W400A (GA) 1-13
Page 22
KLV-40W400A
1-2-7. LCD PANEL, H3E BOARD AND H4 BOARD REMOVAL
7 LCD panel (40INCH FHD TFT)
6 Illumination module
9 Bezel assy (40)
Both
1 H3E board
2 H4 board
3 One screw
(+BVTP 3X12)
4 Light guide
5 Clear (M) panel
Both
KLV-32/40/46/52W400A (GA) 1-14
Page 23
KLV-40W400A
T- CON
SWITCH UNIT
CN6154
CN6000
CN6151
CN6150
CN6700
CN6706
INVERTER
IP5 board
CN102
CN101
CN104
AC inlet
CN5501
CN5500
CN8001
CN3004
CN2001
CN4001
CN3003
CN4000
BG1G board
H4 board
H3E board
CN401
CN301
ILLUMINATION
MODULE
Speaker (R)
Speaker (L)
1-2-8. WIRING LAYOUT
KLV-32/40/46/52W400A (GA) 1-15
Page 24
1-3. KLV-46W400A
1-3-1. REAR COVER AND STAND ASSY REMOVAL
2 Two screws
(+PSW M5X8)
1 Six screws
(+BVTP2 4X16)
4 Two screws
(+BVST 3X8)
5 Two screws
(+BVTP2 3X12)
1 Eleven screws
(+BVTP2 4X16)
3 Two screws
(+PSW M5X12)
6 Rear cover assy
8 Stand assy (L)
1 Six screws
(+BVTP2 4X16)
7 Three screws
(+PSW M5X16)
9 Switch unit
KLV-32/40/46/52W400A (GA) 1-16
Page 25
KLV-46W400A
1-3-2. AC INLET AND UNDER COVER REMOVAL
2 Under bar (L)
7 Two Sscrews
(+BVST 3X8)
8 AC inlet bracket
6 AC inlet
4 Under cover (L2)
1 Two screws
(+BVTP2 4X16)
5 Two screws
(+KTT 3X10)
3 One screws
(+BVST 3X8)
KLV-32/40/46/52W400A (GA) 1-17
Page 26
KLV-46W400A
1-3-3. BG1G BOARD AND IP5 BOARD REMOVAL
5 Two screws
(+BVST 3X8)
8 Three screws
(+BVST 3X8)
7 Side jack
bracket assy
0 One screw
(+BVST 3X8)
qa Harness with
connector (LVDS)
9 BG1G board
qd G5 frame
6 B(G) shield
8 Six screws
(+BVST 3X8)
qs Two screws
(+BVST 3X8)
3 Three screws
(+BVST 3X8)
1 Two screws
(+PSW M5X8)
4 IP5 board
3 Three screws
(+BVST 3X8)
2 Center frame
KLV-32/40/46/52W400A (GA) 1-18
Page 27
KLV-46W400A
1-3-4. FRAME REMOVAL
7 Two screws (+PSW M5X8)
1 One screw
(+PSW M5X8)
2 Center frame
qa Five screws
(+PSW M5X8)
qs Spine frame
assy
8 Vesa frame (BTM) assy
1 One screw
(+PSW M5X8)
3 Two screws (+BVST 3X8)
5 Two scxrews (+PSW M5X8)
6 Vesa frame (BTM) assy
4 G5 frame
9 Five screws
(+PSW M5X8)
0 Spine frame assy (46)
qd Two screws
(+BVTP2 4X16)
qf Bottom frame
assy
KLV-32/40/46/52W400A (GA) 1-19
Page 28
KLV-46W400A
1-3-5. SPEAKER (L) REMOVAL
1 Loudspeaker
2 Speaker cushion
Both
Both
1-3-6. SPEAKER (R) REMOVAL
1 Loudspeaker
Both
2 Speaker cushion
Both
KLV-32/40/46/52W400A (GA) 1-20
Page 29
5 Clear (M) panel
4 Light guide
3 One screw
(+BVTP 3X12)
7 LCD panel (46INCH FHD TFT)
6 Illumination module
8 Bezel assy (46)
2 H4 board
1 H3E board
Both
Both
KLV-46W400A
1-3-7. LCD PANEL, H3E BOARD AND H4 BOARD REMOVAL
KLV-32/40/46/52W400A (GA) 1-21
Page 30
KLV-46W400A
1-3-8. WIRING LAYOUT
CN1
INVERTER
CN125
CN128
SWITCH UNIT
CN6700
CN6706
T-CON
IP5 board
AC inlet
CN6154
CN6151
CN6150
CN6000
CN4001
CN5501
CN5500
CN3004
CN4000
CN8001
BG1G board
CN401
CN301
H4 board
H3E board
ILLUMINATION
MODULE
CN2001
CN3003
Speaker (R)Speaker (L)
KLV-32/40/46/52W400A (GA) 1-22
Page 31
1-4. KLV-52W400A
1-4-1. REAR COVER AND STAND ASSY REMOVAL
3 Seven screws
(+BVTP2 4X16)
4 Two screws
(+PSW M5X16)
3 Six screws
(+BVTP2 4X16)
5 Four screws
(+PSW M5X8)
3 Six screws
(+BVTP2 4X16)
6 One screw
(+BVTP 3X12)
7 Rear cover assy
1 Four screws
(+PSW M5X16)
2 Stand assy (L)
8 Switch unit
KLV-32/40/46/52W400A (GA) 1-23
Page 32
KLV-52W400A
1-4-2. AC INLET AND UNDER COVER REMOVAL
5 Two screws
(+KTT 3X10
(S TYPE))
7 Two screws
(+BVST 3X8)
8 AC inlet braket
6 AC inlet
4 Under cover (LL)
2 Under bar (L)
1 Two screws (+BVTP2 4X16)
3 One screw
(+BVST 3X8)
KLV-32/40/46/52W400A (GA) 1-24
Page 33
KLV-52W400A
1-4-3. D4, D5, G5 AND BG1B BOARDS REMOVAL
7 Side jack bracket assy
9 Harness with
connector (LVDS)
3 Four screws
(+BVST 3X8)
4 D5 board
qs Three screws
(+BVST 3X8)
8 One screw
(+BVST 3X8)
qf Three screws
(+BVST 3X8)
0 Two screws
(+BVST 3X8)
qa B(G) shield
qd BG1G board
qg Main bracket
assy
qj G5 board
qs Six screws
(+BVST 3X8)
qf Two screws
(+BVST 3X8)
1 Two screws
(+PSW M5X8)
qh Three screws
(+BVST 3X8)
ql D4 board
qk Four SCREWS
(+BVST 3X8)
5 Two screws
(+BVST 3X8)
5 D5 frame
2 Center frame
KLV-32/40/46/52W400A (GA) 1-25
Page 34
KLV-52W400A
1-4-4. FRAME REMOVAL
1 One screw
(+PSW M5X8)
2 Center frame
7 Five screws
(+PSW M5X8)
5 Two screws
(+PSW M5X8)
6 Vesa frame(BTM)
assy
3 Two screws
(+BVST 3X8)
4 G5 frame
9 Two screws
(+PSW M5X8)
0 Vesa frame (BTM)
assy
qa Five screws
(+PSW M5X8)
8 Spine frame
assy
1 One screw
(+PSW M5X8)
qs Spine frame
ASSY
qd Two screws
(+BVTP2 4X16)
qf Bottomu frame
assy
KLV-32/40/46/52W400A (GA) 1-26
Page 35
KLV-52W400A
1-4-5. SPEAKER (L) REMOVAL
Both
1 Loudspeaker
2 Speaker cushion
Both
1-4-6. SPEAKER (R)
1 Loudspeaker
Both
2 Speaker cushion
Both
KLV-32/40/46/52W400A (GA) 1-27
Page 36
KLV-52W400A
1-4-7. LCD PANEL, H3E BOARD AND H4 BOARD REMOVAL
8 LCD panel (52INCH FHD TFT)
7 Two screws
(+BVTP2 4X16)
5 Clear (M) panel
6 Illumination module
9 Bezel assy
Both
1 H3E board
2 H4 board
3 One screw
(+BVTP 3X12)
4 Light guide
Both
KLV-32/40/46/52W400A (GA) 1-28
Page 37
KLV-52W400A
1-4-8. WIRING LAYOUT
SWITCH UNIT
T- CON
CN05
CN01
INVERTER
CN11
CN401
CN301
CN6705
CN6706
H4 board
D4 board
CN6706
H3E board
CN6600
CN6702
CN6501 CN6500
G5 board
AC inlet
ILLUMINATION
MODULE
CN6153
CN6100
CN6150
CN6154
CN6000
CN6900
CN6954
D5 board
CN6950
CN4001
CN5501
CN5500
CN3004
CN2001
CN07
INVERTER
CN4000
CN8001
BG1G board
CN3003
Speaker (R)Speaker (L)
KLV-32/40/46/52W400A (GA) 1-29E
Page 38
2-1. CIRCUIT BOARDS LOCATION
Illumination module
H4 board
H3E board
Inverter board
BG1G board
IP5 board
Switch Unit
Illumination module
H4 board
H3E board
Inverter board
Inverter board
BG1G board
G5 board
D4 board
Switch Unit
D5 board
(1) KLV-32W400A
BG1G board
Illumination module
SECTION 2
DIAGRAMS
(3) KLV-46W400A
Switch unit
Power unit
H4 board
(2) KLV-40W400A
BG1G board
H3E board
(4) KLV-52W400A
Switch Unit
IP5 board
Inverter board
Illumination module
H4 board
H3E board
KLV-32/40/46/52W400A (GA) 2-1
Page 39
2-2. BLOCK DIAGRAM
(1) BG1G Board
CVBS
Y/C
CVBS+Y/C
Analog-Component/RGB
Digital-Component
PC-RGB
Audio (Analog)
Audio (Digital)
RF
Component1
Component2
Analog
Tuner
PLL $C0
VIF $86
A-Tuner
For service
I2C-TUNER
Sub Chroma Dec
NICAM
MSP3417G
$80
USB
SAA7115A
$42
USB
Host
NOR
Flash
4MByte
D-Comp[7:0]
CLK/Hs/Vs
Temp
Sensor
$49
SIO
16bit
BUS
ECS
UART
Main Micro
MB91305
I2C-DEVIC
I2C-EEPROM
8bit Multiplex BUS
Port I2C-0
RTC
$60
I2C-TAS
EEP
$A0
A-Tuner
PC
Audio
for PC for DVI
CXB1444R
Hs/Vs
TMDS
Chroma Dec/IP
/Scalar
Trident SVP-WX
HDMI1
SW
DDR
256Mbit/32bit/
250MHz
HDMI2
I2S
Audio
HDMI3
Panel
Backlight
Inverter
Panel
FHD
(S)Video1
Video2
Video3
DM Port
Monitor out
Audio out
(Var.)
UART-4
Video SW
CXA2241
$90
DMP IN
LINE OUT
AudioOUT
CXA3767R
$94
DMP IN
Line OUT
HPOUT
SPOUT
Audio out
Audio SW
AD/DA
DSP
TAS3308
$68
SP OUT
HP OUT
Audio Amp.
TPA3100D2
2ch Speaker
HP
KLV-32/40/46/52W400A (GA) 2-2E
Page 40
SECTION 3
EXPLODED VIEWS
NOTE: • Items with no part number and no description are
not stocked because they are seldom required for
roution service.
• The construction parts of an assembled part are
indicated with a collation number in the remark
colum.
• Items marked " * " are not stocked since they are
seldom required for routine service. Some delay
should be anticipated when ordering these items.
KLV-32/40/46/52W400A (GA) 3-1
Page 41
3-1. KLV-32W400A
3-1-1. REAR COVER AND STAND ASSY
3
1
#1
1
2
1
6
4
6
7
5
REF. No. PART No. DESCRIPTION MARK
1 2-580-640-01 SCREW, +BVTP2 4X16
2 2-580-629-01 SCREW, +BVST 3X8
3 2-580-606-01 SCREW, +PSW M5X8
4 ! X-2189-293-1 REAR COVER (32) ASSY
5 X-2189-409-1 STAND (M) ASSY
REF. No. PART No. DESCRIPTION MARK
6*3-106-086-02 COVER, ECS
7 2-580-608-01 SCREW, +PSW M5X16
#1 7-685-648-79 SCREW +BVTP 3X12 TYPE2 IT-3
KLV-32/40/46/52W400A (GA) 3-2
Page 42
KLV-32W400A
3-1-2. CHASSIS-1
51
61
60
53
53
52
53
55
58
59
53
63
56
53
53
57
57
54
53
63
62
59
REF. No. PART No. DESCRIPTION MARK REF. No. PART No. DESCRIPTION MARK
51 1-480-709-11 SWITCH UNIT
52 1-966-049-11 HARNESS WITH CONNECTOR (LVDS)
53 2-580-629-01 SCREW, +BVST 3X8
54 2-580-626-01 SCREW, SP 4-4O UNC
55 A-1512-199-A BG1G COMPL
56 X-2318-263-1 SIDE JACK BRACKET (EX1) ASSY
57 2-580-590-01 SCREW , +PSW M3X5
58 1-474-099-11 POWER UNIT
59 2-674-965-31 SCREW, +PSW 3SG
60 ! 1-835-127-11 POWER SUPPLY (WITH CONNECTOR)
(Thailand)
! 1-835-280-11 POWER SUPPLY (WITH CONNECTOR)
(India)
! 1-835-136-11 POWER SUPPLY (WITH CONNECTOR)
(E, Saudi arabia, Middle East, Indonesia,
Saudi arabia, Philippines)
61 4-022-115-00 HOLDER, AC CORD
62 2-580-640-01 SCREW, +BVTP2 4X16
63 2-580-600-01 SCREW, +PSW M4X8
63
KLV-32/40/46/52W400A (GA) 3-3
Page 43
KLV-32W400A
101
107
111
110
108
109
#1
103
105
105
105
106
102
105
105
105
104
112
3-1-3. CHASSIS-2
REF. No. PART No. DESCRIPTION MARK REF. No. PART No. DESCRIPTION MARK
101 X-2189-289-1 BEZEL ASSY (32EM)
102 1-826-869-11 LOUDSPEAKER (5.5X12.6CM)
103 ! 1-802-648-12 LCD PANEL (32INCH FHD TFT)
104 1-480-680-11 ILLUMINATION MODULE
105 2-580-600-01 SCREW, +PSW M4X8
106 2-580-640-01 SCREW, +BVTP2 4X16
107 1-826-869-21 LOUDSPEAKER (5.5X12.6CM)
108 A-1510-351-A H4 MOUNT
109 3-290-361-01 GUIDE, LIGHT
110 A-1510-350-A H3E MOUNT
111 3-289-963-01 PANEL, CLEAR (32)
112 2-580-640-01 SCREW, +BVTP2 4X16
#1 7-685-648-79 SCREW +BVTP 3X12 TYPE2 IT-3
KLV-32/40/46/52W400A (GA) 3-4
Page 44
3-2. KLV-40W400A
3-2-1. REAR COVER AND STAND ASSY
151 153 151
1
151
1
152
#1
151151
155
154
153
156
REF. No. PART No. DESCRIPTION MARK
151 2-580-640-01 SCREW, +BVTP2 4X16
152 2-580-606-01 SCREW, +PSW M5X8
153 2-580-607-01 SCREW, +PSW M5X12
154 ! X-2189-302-1 REAR COVER ASSY (40)
155 * 3-106-086-02 COVER, ECS
REF. No. PART No. DESCRIPTION MARK
156 X-2189-410-1 STAND (ML) ASSY
#1 7-685-648-79 SCREW +BVTP 3X12 TYPE2 IT-3
KLV-32/40/46/52W400A (GA) 3-5
Page 45
KLV-40W400A
201
203
203
202
203
205
203
203
203
203
210
208
203
206
207
203
211
203
209
204
3-2-2. CHASSIS-1
REF. No. PART No. DESCRIPTION MARK REF. No. PART No. DESCRIPTION MARK
201 1-480-709-11 SWITCH UNIT
202 1-835-275-11 HARNESS WITH CONNECTOR (LVDS)
203 2-580-629-01 SCREW, +BVST 3X8
204 2-580-626-01 SCREW, SP 4-4O UNC
205 A-1512-185-A BG1G COMPL
206 2-596-649-01 +KTT 3X10 (S TYPE)
207 ! 1-821-909-11 AC INLET
208 2-580-640-01 SCREW, +BVTP2 4X16
209 2-580-590-01 SCREW , +PSW M3X5
210 A-1511-388-A IP5 COMPL
211 X-2318-263-1 SIDE JACK BRACKET (EX1) ASSY
KLV-32/40/46/52W400A (GA) 3-6
Page 46
KLV-40W400A
3-2-3. CHASSIS-2
251
257
261
254
260
259
#1
258
252
253
262
255
256
255
256
256
256
REF. No. PART No. DESCRIPTION MARK REF. No. PART No. DESCRIPTION MARK
251 X-2189-299-1 BEZEL ASSY (EM40)
252 1-826-888-11 LOUDSPEAKER
253 ! 1-802-664-11 LCD PANEL (40INCH FHD TFT)
254 1-480-680-11 ILLUMINATION MODULE
255 2-580-600-01 SCREW, +PSW M4X8
256 2-580-606-01 SCREW, +PSW M5X8
257 1-826-888-21 LOUDSPEAKER
258 A-1510-351-A H4 MOUNT
259 3-290-361-01 GUIDE, LIGHT
260 A-1510-350-A H3E MOUNT
261 3-289-965-01 PANEL, CLEAR (40)
262 2-580-640-01 SCREW, +BVTP2 4X16
#1 7-685-648-79 SCREW +BVTP 3X12 TYPE2 IT-3
KLV-32/40/46/52W400A (GA) 3-7
Page 47
3-3. KLV-46W400A
3-3-1. REAR COVER AND STAND ASSY
303
302
301
302
304
#1
302
305
306
306
301
REF. No. PART No. DESCRIPTION MARK
301 2-580-607-01 SCREW, +PSW M5X12
302 2-580-640-01 SCREW, +BVTP2 4X16
303 2-580-606-01 SCREW, +PSW M5X8
304 2-580-629-01 SCREW, +BVST 3X8
305 ! X-2189-301-1 REAR COVER (46) ASSY
307
REF. No. PART No. DESCRIPTION MARK
306 * 3-106-086-02 COVER, ECS
307 X-2189-411-1 STAND (L) ASSY
#1 7-685-648-79 SCREW +BVTP 3X12 TYPE2 IT-3
KLV-32/40/46/52W400A (GA) 3-8
Page 48
KLV-46W400A
3-3-2. CHASSIS-1
351
352
352
360
355
356
352
356
356
354
352
356
356
353
352
362
356
356
359
361
357
356
356
358
REF. No. PART No. DESCRIPTION MARK REF. No. PART No. DESCRIPTION MARK
351 1-480-709-11 SWITCH UNIT
352 2-580-606-01 SCREW, +PSW M5X8
353 A-1512-201-A BG1G COMPL
354 1-966-050-11 HARNESS WITH CONNECTOR (LVDS)
355 2-596-649-01 +KTT 3X10 (S TYPE)
352
356 2-580-629-01 SCREW, +BVST 3X8
357 A-1511-389-A IP5 COMPL
358 2-580-640-01 SCREW, +BVTP2 4X16
359 2-580-590-01 SCREW , +PSW M3X5
360 ! 1-821-909-11 AC INLET
356
361 2-580-626-01 SCREW, SP 4-4O UNC
362 X-2318-263-1 SIDE JACK BRACKET (EX1) ASSY
KLV-32/40/46/52W400A (GA) 3-9
Page 49
KLV-46W400A
3-3-3. CHASSIS-2
401
405
402
406
402
403
408
#1
407
404
REF. No. PART No. DESCRIPTION MARK
401 X-2189-307-1 BEZEL ASSY (46EM)
402 1-480-680-11 ILLUMINATION MODULE
403 1-826-887-11 LOUDSPEAKER
404 1-826-887-21 LOUDSPEAKER
405 ! 1-802-663-11 LCD PANEL (46INCH FHD TFT)
REF. No. PART No. DESCRIPTION MARK
406 A-1510-350-A H3E MOUNT
407 A-1510-351-A H4 MOUNT
408 3-290-361-01 GUIDE, LIGHT
#1 7-685-648-79 SCREW +BVTP 3X12 TYPE2 IT-3
KLV-32/40/46/52W400A (GA) 3-10
Page 50
3-4. KLV-52W400A
3-4-1. REAR COVER AND STAND ASSY
451
452
#1
457
453 453
451451
456
455
453
REF. No. PART No. DESCRIPTION MARK
451 2-580-640-01 SCREW, +BVTP2 4X16
452 2-580-606-01 SCREW, +PSW M5X8
453 2-580-607-01 SCREW, +PSW M5X16
454 X-2190-786-1 STAND ASSY (LL)
455 * 3-106-086-02 COVER, ECS
454
REF. No. PART No. DESCRIPTION MARK
456 3-284-261-11 REAR, COVER (52)
467 2-580-629-01 SCREW, +BVST 3X8
#1 7-685-648-79 SCREW +BVTP 3X12 TYPE2 IT-3
KLV-32/40/46/52W400A (GA) 3-11
Page 51
KLV-52W400A
3-4-2. CHASSIS-1
501
503
510
503
509
506
503
503
512
503
502
508
503
503
503
503
503
505
504
503
503
513
503
507
511
REF. No. PART No. DESCRIPTION MARK REF. No. PART No. DESCRIPTION MARK
501 1-480-709-11 SWITCH UNIT
502 1-966-051-11 HARNESS WITH CONNECTOR (LVDS)
503 2-580-629-01 SCREW, +BVST 3X8
504 ! A-1511-383-A D5 COMPL
505 A-1512-203-B BG1G COMPL
506 2-596-649-01 +KTT 3X10 (S TYPE)
507 2-580-590-01 SCREW , +PSW M3X5
508 ! A-1511-323-B G5 COMPL
509 3-284-269-01 COVER,UNDER (LL)
510 ! A-1511-382-A D4 COMPL
511 2-580-626-01 SCREW, SP 4-4O UNC
512 ! 1-821-909-11 AC INLET
513 X-2318-263-1 SIDE JACK BRACKET (EX1) ASSY
KLV-32/40/46/52W400A (GA) 3-12
Page 52
KLV-52W400A
3-4-3. CHASSIS-2
551
553
554
562
552
561
559
#1
560
558
556
405
555
556
556
556
556
556
557
REF. No. PART No. DESCRIPTION MARK REF. No. PART No. DESCRIPTION MARK
551 X-2190-419-1 BEZEL ASSY (52EM)
552 1-480-680-11 ILLUMINATION MODULE
553 1-826-887-11 LOUDSPEAKER (3CM, 6.5X15CM)
554 ! 1-802-662-11 LCD PANEL (52INCH FHD TFT)
555 2-580-640-01 SCREW, +BVTP2 4X16
556 2-580-629-01 SCREW, +BVST 3X8
557 2-580-629-01 SCREW, +BVST 3X8
558 * 3-284-247-41 PANEL, CLEAR (52)
559 3-290-361-01 GUIDE, LIGHT
560 A-1510-351-A H4 MOUNT
561 A-1510-350-A H3E MOUNT
562 1-826-887-21 LOUDSPEAKER (3CM, 6.5X15CM)
#1 7-685-648-79 SCREW +BVTP 3X12 TYPE2 IT-3
KLV-32/40/46/52W400A (GA) 3-13
Page 53
3-5. PACKING MATERIALS
3-5-1. KLV-32W400A
602
601
605
603
604
606
607
REF. No. PART No. DESCRIPTION MARK
601 * 3-295-216-01 CUSHION (LOWER)
602 3-874-376-01 BAG, PROTECTION
603 * 3-295-215-01 CUSHION (UPPER)
604 * 3-295-214-01 INDIVIDUAL CARTON
605 ! 3-295-292-12 MANUAL,INSTRUCTION (E, Indonesia,
India, Middle East, Saudi arabia)
! 3-295-292-22 MANUAL,INSTRUCTION
(E, Middle East)
! 3-295-292-32 MANUAL,INSTRUCTION
(Indonesia, Saudi arabia)
! 3-295-292-42 MANUAL,INSTRUCTION (Indonesia)
! 3-299-348-11 MANUAL,INSTRUCTION
(Thailand, South Africa, Philippines)
! 3-299-348-21 MANUAL,INSTRUCTION (Thailand)
REF. No. PART No. DESCRIPTION MARK
606 * 3-295-308-12 MANUAL,INSTRUCTION
(WALL MOUNT) (E, India, Indonesia
Middle East, Saudi arabia)
* 3-295-308-22 MANUAL,INSTRUCTION
(WALL MOUNT) (Thailand, South Africa,
Philippines)
607 1-480-705-11 REMOTE COMMANDER (RM-GA011)
KLV-32/40/46/52W400A (GA) 3-14
Page 54
3-5-2. KLV-40W400A
653 654
656
657
565
652
651
REF. No. PART No. DESCRIPTION MARK
651 1-480-705-11 REMOTE COMMANDER (RM-GA011)
652 ! 1-835-126-11 POWER SUPPLY CORD SET (Thailand)
! 1-835-138-11 POWER SUPPLY CORD SET
! 1-835-165-11 POWER SUPPLY CORD SET
! 1-835-166-11 POWER SUPPLY CORD SET
! 1-835-200-11 POWER SUPPLY CORD SET (Indonesia)
! 1-835-281-11 POWER SUPPLY CORD SET (India)
653 ! 3-295-292-12 MANUAL,INSTRUCTION
! 3-295-292-22 MANUAL,INSTRUCTION (E, Middle East)
! 3-295-292-32 MANUAL,INSTRUCTION
! 3-295-292-42 MANUAL,INSTRUCTION (Indonesia)
! 3-299-348-11 MANUAL,INSTRUCTION
! 3-299-348-21 MANUAL,INSTRUCTION (Thailand)
(Saudi Arabia, Philippines)
(E, Saudi Arabia, Middle East, Indonesia)
(South Africa)
(E, Indonesia, India, Middle East, Saudi
arabia)
(Indonesia, Saudi arabia)
(Thailand, South Africa, Philippines)
REF. No. PART No. DESCRIPTION MARK
654 * 3-295-308-12 MANUAL,INSTRUCTION
(WALL MOUNT) (E, Indonesia, India,
Middle East, Saudi arabia)
* 3-295-308-22 MANUAL,INSTRUCTION
(WALL MOUNT) (Thailand, South Africa,
Philippines)
655 * 3-295-296-01 CUSHION (LOWER)
656 * 3-295-295-01 CUSHION (UPPER)
657 * 3-295-294-01 INDIVIDUAL CARTON
KLV-32/40/46/52W400A (GA) 3-15
Page 55
3-5-3. KLV-46W400A
706
701
702
703 704
705
708
707
REF. No. PART No. DESCRIPTION MARK REF. No. PART No. DESCRIPTION MARK
701 1-480-705-11 REMOTE COMMANDER (RM-GA011)
702 ! 1-835-126-11 POWER SUPPLY CORD SET (Thailand)
! 1-835-138-11 POWER SUPPLY CORD SET
(Saudi Arabia, Philippines)
! 1-835-165-11 POWER SUPPLY CORD SET
(E, Saudi Arabia, Middle East, Indonesia)
! 1-835-166-11 POWER SUPPLY CORD SET
(South Africa)
! 1-835-200-11 POWER SUPPLY CORD SET (Indonesia)
! 1-835-281-11 POWER SUPPLY CORD SET (India)
703 ! 3-295-292-12 MANUAL,INSTRUCTION
(E, India, Saudi Arabia, Middle East,
Indonesia)
! 3-295-292-22 MANUAL,INSTRUCTION (E, Middle East)
! 3-295-292-32 MANUAL,INSTRUCTION
(South Africa, Indonesia)
! 3-295-292-42 MANUAL,INSTRUCTION (Indonesia)
! 3-299-348-11 MANUAL,INSTRUCTION
(Thailand, South Africa, Philippines)
! 3-299-348-21 MANUAL,INSTRUCTION (Thailand)
704 * 3-295-308-12 MANUAL,INSTRUCTION
(WALL MOUNT) (E, ID, SA, ME, EA)
* 3-295-308-22 MANUAL,INSTRUCTION
(WALL MOUNT) (Thailand, South Africa,
Philippines)
705 * 3-295-300-01 CUSHION (LOWER)
706 * 3-295-299-01 CUSHION (UPPER)
707 * 2-639-807-01 JOINT
708 * 3-295-297-01 INDIVIDUAL CARTON
KLV-32/40/46/52W400A (GA) 3-16
Page 56
3-5-4. KLV-52W400A
757
758
756
754
759
755
753
752
760
751
REF. No. PART No. DESCRIPTION MARK
751 3-295-390-01 TRAY
752 * 3-295-392-01 CUSHION LOWER
753 S 1-480-705-11 REMOTE COMMANDER (RM-GA011)
754 ! 3-295-292-12 MANUAL,INSTRUCTION
(E, India, Saudi Arabia, Middle East,
Indonesia)
! 3-295-292-22 MANUAL,INSTRUCTION (E, Middle East)
! 3-295-292-32 MANUAL,INSTRUCTION
(Saudi Arabia, Indonesia)
! 3-295-292-42 MANUAL,INSTRUCTION (Indonesia)
! 3-299-348-11 MANUAL,INSTRUCTION
(Thailand, South Africa, Philippines)
! 3-299-348-21 MANUAL,INSTRUCTION (Thailand)
755 * 3-295-308-12 MANUAL,INSTRUCTION
(WALL MOUNT) (E, India, Saudi Arabia,
Middle Eas, Indonesia)
* 3-295-308-22 MANUAL,INSTRUCTION
(WALL MOUNT) (Thailand, South Africa,
Philippines)
REF. No. PART No. DESCRIPTION MARK
756 ! 1-835-126-11 POWER SUPPLY CORD SET (Thailand)
! 1-835-138-11 POWER SUPPLY CORD SET
(Saudi Arabia, Philippines)
! 1-835-165-11 POWER SUPPLY CORD SET
(E, Saudi Arabia, Middle East, Indonesia)
! 1-835-166-11 POWER SUPPLY CORD SET
(South Africa)
! 1-835-200-11 POWER SUPPLY CORD SET
(Indonesia)
! 1-835-281-11 POWER SUPPLY CORD SET (India)
757 3-874-377-01 BAG, PROTECTION
758 * 3-295-391-01 CUSHION UPPER
759 * 3-295-389-01 INDIVIDUAL CARTON
760 * 2-639-807-01 JOINT
KLV-32/40/46/52W400A (GA) 3-17E
Page 57
9-888-204-01
Sony EMCS Corporation
Inazawa TEC
English
2008BL08-Data
Made in Japan
2008. 2
KLV-32/40/46/52W400A (GA) 57
Loading...