Sony KDE-50XS955, KDE-37XS955 User Manual

Flat Panel Color TV KDE-37XS955/KDE-42XS955/KDE-50XS955

2-148-836-13 (1)

Printed on 100% recycled paper.

Printed in Japan

Flat Panel Color TV Operating Instructions

KDE-37XS955 KDE-42XS955 KDE-50XS955

 2004 Sony Corporation

Owner’s Record

The model and serial numbers are located at the rear of the TV. Record these numbers in the spaces provided below. Refer to them whenever you call upon your Sony dealer regarding this product.

Model No.

Serial No.

Contacting Sony

If, after reading these operating instructions, you have additional questions related to the use of your Sony television, please call our Customer Information Services Center at 1-800-222-SONY (7669) (US residents only) or 1-877-899-SONY (7669) (Canadian residents only).

WARNING

To reduce the risk of fire or shock hazard, do not expose the TV to rain or moisture.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ATTENTION

RISQUE DE CHOC ELECTRIQUE,

NE PAS OUVRIR

PRECAUCION

RIESGO DE CHOQUE ELECTRICO

NO ABRIR

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION

To prevent electric shock, do not use this polarized AC plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure.

Note on Caption Vision

This television receiver provides display of television closed captioning in accordance with ß15.119 of the FCC rules.

Note to CATV System Installer

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electrical Code (NEC) that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

Use of this television receiver for other than private viewing of programs broadcast on UHF or VHF or transmitted by cable companies for the use of the general public may require authorization from the broadcaster/cable company and/or program owner.

NOTIFICATION

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference with radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment d oes cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

s Reorient or relocate the receiving

antennas.

s Increase the separation between the

equipment and receiver.

s Connect the equipment into an outlet on a

circuit different from that to which the receiver is connected.

s Consult the dealer or an experienced

radio/TV technician for help.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

Safety

s Operate the TV only on 120 V AC. s The plug is designed, for safety purposes,

to fit into the wall outlet only one way. If you are unable to insert the plug fully into the outlet, contact your dealer.

s If any liquid or solid object should fall

inside the cabinet, unplug the TV immediately and have it checked by qualified service personnel before operating it further.

s If you will not be using the TV for several

days, disconnect the power by pulling the plug itself. Never pull on the cord.

s For details concerning safety precautions,

see “Important Safeguards” on page 2.

Important Notice

s When used at an altitude of greater than

1,900m or 6,248feet (air pressure less than 800hPa), this Plasma Display Panel may generate a low buzzing sound as a result of the difference between the interior and exterior air pressure of the panels. This is not considered a defect and is not covered under by the Limited Warranty.

Installing

s To prevent internal heat buildup, do not

block the ventilation openings.

s Do not install the TV in a hot or humid

place, or in a place subject to excessive dust or mechanical vibration.

s Avoid operating the TV at temperatures

below 5°C (41°F).

s If the TV is transported directly from a

cold to a warm location, or if the room temperature changes suddenly, the picture may be blurred or show poor color due to moisture condensation. In this case, please wait a few hours to let the moisture evaporate before turning on the TV.

s To obtain the best picture, do not expose

the screen to direct illumination or direct sunlight. It is recommended to use spot lighting directed down from the ceiling or to cover the windows that face the screen with opaque drapery. It is desirable to install the TV in a room where the floor and walls are not of a reflective material.

CAUTION

Bright, stationary images, such as TV station logos, displayed on your TV can become permanently imprinted onto the screen. Theses types of imprints are known as “Image Retention.” Please take the following steps to reduce the risk of causing image retention:

View a variety of program sources or programming material. Changing the program material viewed reduces the possibility that a single image will become imprinted on the TV screen.

When using video games, computers, and similar products with your TV, or viewing a TV station whose logo always stays on the screen, keep the “Brightness” and “Picture” functions at low settings. (See page 92 for instructions on adjusting picture quality.)

This TV was designed primarily for viewing TV broadcasts in wide screen mode (16:9 aspect ratio). Therefore, when viewing conventional (4:3) aspect ratio TV programs, select “Wide Zoom” or “Full” in the Wide Screen Mode, or “4:3 Default” in the Screen menu (see pages 97-98).

IMAGE RETENTION IS NOT COVERED BY YOUR WARRANTY.

(Continued)

CAUTION

Use the following SONY appliance(s) only with the following WALL-MOUNT BRACKET. Use with other WALL-MOUNT BRACKET may cause instability and result in possible injury.

SONY APPLIANCE MODEL NO. KDE-37XS955 KDE-42XS955 KDE-50XS955

SONY WALL-MOUNT BRACKET MODEL NO. SU-PW3M

SONY FLOATING STAND MODEL NO. SU-PF3L (for KDE-50XS955) SU-PF3M (for KDE-37/42XS955)

To Customers

Sufficient expertise is required for installing the specified product. Be sure to subcontract the installation to Sony dealers or contractors and pay adequate attention to safety during the installation.

To Sony Dealers

For installation of SONY WALL-MOUNT BRACKET, or SONY FLOATING STAND, be sure to read and follow the instructions supplied with those optional products.

Trademark Information

TruSurround, SRS and the symbol are trademarks of SRS Labs, Inc. TruSurround technology is incorporated under license from SRS Labs, Inc.

Licensed by BBE Sound, Inc. under USP4638258, 4482866. “BBE” and BBE symbol are trademarks of BBE Sound, Inc.

Steady Sound, Digital Reality Creation, CineMotion, Memor y Stick, and Twin View are registered trademarks of Sony Corporation. BN Smoother is trademark of Sony Corporation.

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

This TV incorporates High-Definition

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

™

CableCARD

is a trademark of Cable Television Laboratories, Inc.

Multimedia Interface (HDMI™) technology.

Important Safeguards

Before using your TV, please read these instructions completely, and keep this manual for future reference.

Carefully observe and comply with all warnings, cautions and instructions placed on the unit or described in the operating instructions or service manual.

WARNING

To guard against injury, the following basic safety precautions should be observed in the installation, use and servicing of the unit.

Use

Power Sources

This unit should be operated only from the type of power source indicated on the serial/model plate. If you are not sure of the type of electrical power supplied to your home, consult your dealer or local power company. For those sets designed to operate from battery power, refer to the o pe ra tin g instructions.

Grounding or Polarization

This unit is equipped with a polarized AC power cord plug (a plug having one blade wider than the other), or with a three-wire grounding type plug (a plug having a third pin for grounding). Follow the instructions below:

For the unit with a polarized AC power cord plug

This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug.

If the plug still fails to fit, contact your electrician to have a suitable outlet installed. Do not defeat the safety purpose of the polarized plug by forcing it in.

Wall outlet

Do not use a poor fitting outlet. Insert the plug fully into the outlet. If it is loose, it

may cause arcing and result in fire. Contact your electrician to have the outlet changed.

This digital television is capable of receiving analog basic, digital basic and digital premium cable television programming by direct connection to a cable system providing such programming. A security card provided by your cable operator is required to view encrypted digital programming. Certain advanced and interactive digital cable services such as video-on-demand, a cable operator's enhanced program guide and data-enhanced television services may require the use of a set-top box. For more information call your local cable operator.

Wiring

For your safety, unplug the AC power cord when wiring cables.

Moisture

Do not touch the AC power cord or the unit with a wet hand.

If you plug/unplug the AC power cord from the unit with a wet hand, it may cause electric shock.

Cleaning

Clean the AC power plug regularly. If the plug is covered with dust and it picks up

moisture, its insulation may deteriorate and result in fire. Unplug the AC power plug and clean it regularly.

Ventilation holes

Do not insert anything in the ventilation holes. If metal or something flammable enters, it may result in fire or electric shock.

For the unit with a three-wire grounding type AC plug

This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to have a suitable outlet installed. Do not defeat the safety purpose of the grounding plug.

Overloading

Do not overload wall outlets, extension cords or convenience receptacles beyond their capacity, since this can result in fire or electric shock.

Always turn the unit off when it is not being used. When the unit is left unattended and unused for long periods of time, unplug it from the wall outlet as a precaution against the possibility of an internal malfunction that could create a fire hazard.

If a snapping or popping sound from a TV unit is continuous or frequent while the TV is operating, unplug the TV and consult your dealer or service technician. It is no rmal for some T V s e ts to make occasional snapping or popping sounds, particularly when being turned on or off.

AC power cord

If you damage the AC power cord, it may result in fire or electric shock.

s Do not pinch, bend, or twist the cord excessively. The core lines may

be bared and cut, and cause short-circuit, resulting in fire or electric shock.

s Do not convert or damage the AC power cord or display interface

cable.

s Do not put anything heavy on the AC power cord. Do not pull the

AC power cord.

s Keep the AC power cord away from heat sources. s Be sure to grasp the plug when disconnecting the AC power cord.

If the AC power cord is damaged, stop using it and ask your dealer or Sony service center to exchange it.

Batteries

Do not dispose of batteries in fire. Do not short circuit, disassemble or overheat the batteries.

Object and Liquid Entry

Never push objects of any kind into the unit through the cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the unit.

Do not place any objects on the unit. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

Cleaning

Unplug the AC power cord when cleaning this unit. If not, it may result in electric shock. Clean the cabinet of the TV with a dry soft cloth. To remove dust from the screen, wipe it gently with a soft cloth. Stubborn stains may be removed with a cloth slightly dampened with a solution of mild soap and warm water. Never use strong solvents such as thinner or benzine for cleaning.

If the picture becomes dark after using the TV for a long period of time, it may be necessary to clean the inside of the TV. Consult qualified service personnel.

Attachments

Do not use attachments not recommended by the manufacturer, as they may cause hazards.

Medical institution

Do not place this unit in a place where medical equipment is in use.

It may cause malfunction of medical instrume nts .

Moisture and flammable objects

s Do not use power-line operated sets near

water — for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc. It may result in fire or electric shock.

s Do not let this unit get wet. Never spill liquid

of any kind on the unit. If any liquid or solid object does fall through, do not operate the unit. It may result in electric shock or damage to the unit. Have it checked immediately by qualified personnel.

s To prevent fire, keep inflammable objects or naked lights (e.g.

candles) away from the unit.

Accessories

Do not place the unit on an unstable cart, stand, table or shelf. The unit may fall, causing serious injury to a child or an adult and serious damage to the unit. Use only a cart or stand recommended by Sony for the specific model of TV. No part of the TV unit should overhang any edge of the TV cart or stand; any overhanging edge is a safety hazard. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

(Continued)(Continued)

Dispose of used batteries

To preserve our environment, dispose the used batteries according to your local laws or regulations.

Damage requiring service

If the surface of the TV cracks, do not touch it until you unplug the AC power cord.

Otherwise electric shock may result.

Broken pieces

Do not throw anything at the unit. The screen glass may break by the impact and cause serious injury.

Cable wiring

Take care not to catch your feet on the cables. It may damage the unit.

Heat

Do not touch the surface of the TV. It remains hot, even for some time after the TV is turned off .

Volume adjustment

Adjust the volume so as not to trouble your neighbors. Sound carries very easily at night time. Therefore, closing the windows or using headphones is suggested.

When using headphones, adjust the volume so as to avoid excessive levels, as hearing damage may result.

Installation and moving

Carry the TV in the specified manner

Carrying the TV requires at least two people. If you carry the TV in a manner other than that specified and without

the specified number of persons, it may drop and a serious injury may result. Be sure to follow the instructions given below.

s Carry the TV with the specified number of

persons.

s Carry the TV holding the upper and bottom

frames of the TV as illustrated. Do not carry by the clear plastic front panel.

s Hold the TV securely when carrying it. s As the glass surface of the TV has a special coating, be careful to

avoid touching the glass surface as far as possible.

s When transporting, do not subject the unit to shocks or vibration, or

excessive force.

Installation

When installing or removing the TV on the wall, be sure to use qualified contractors. Wall mount installation requires the use of a wall-mount bracket. If the TV is installed or removed from the wall by a person other than a qualified contractor, the unit may fall and cause serious injury if the unit is not installed securely.

Placement for viewing

It is recommended to watch the TV at a distance of 3-7 times that of the screen, and in moderate brightness. Watching the TV for too long or in a dark room will cause eye fatigue.

Optional accessories

Observe the following when installing the TV using a stand or wall-mount bracket. If the TV is not secured properly, it may fall and cause injury.

s Be sure to follow the operating instructions

supplied with your stand or wall-mount bracket when installing the unit.

s Be sure to attach the brackets supplied with your stand or

wall-mount bracket.

Protruding location

Do not install the TV in protruding locations. If you install the unit in the following locations, injury may result.

s Do not install the unit in a location where the unit protrudes, such as

pillars.

s Do not install the unit in a location that may cause facial injury.

Oils

Do not install this unit in restaurants where oily vapors occur. Dust absorbing oil may enter into the unit and damage the unit.

Corrosion

Use of this set near the seashore may subject the set to excessive salt, corrosion and internal damage and result in deterioration of the set’s performance. If the set will be subjected to these conditions, steps should be taken to reduce the humidity and temperature of the area where the set is located.

Ventilation

The slots and openings in the TV are provided for necessary ventilation. To ensure reliable operation of the unit, and to protect it from overheating, these slots and openings must never be blocked or covered.

Unless proper ventilation is provided, the unit may gather dust and get dirty. For proper ventilation, Observe the following:

s Do not install the unit turned backward or

sideways.

s Do not install the unit turned over or upside

down.

s Never cover the slots and openings with a

cloth or other materials.

s Never block the slots and openings by

placing the unit on a bed, sofa, rug or other similar surface.

s Never place the unit in a confined space, such as

a bookcase or built-in cabinet, unless proper ventilation is provided.

s Do not place the unit near or over a radiator or

heat register, or where it is exposed to direct sunlight.

s Leave some space around the unit. Otherwise, adequate

air-circulation may be blocked causing overheating and cause fire or damage the unit.

When installing the unit on the wall

10 cm (4 inches)

/8 inches)

10 cm (4 inches)

Allow this much space.

/8 inches)

10 cm (4 inches)

Allow this much space.

10 cm (4 inches)

When installing the unit using a stand

10 cm (4 inches)

Never install the unit as follows:

Air circulation is blocked.

30 cm (11

Air circulation is blocked.

AC power cord

Unplug the AC power cord when moving the unit. Do not move the unit with the AC power cord plugged in. It may damage

the AC power cord and result in fire or electric shock.

Preventing from toppling over

Take measures to prevent the unit from toppling over and causing injury. To prevent the unit from toppling over, secure the unit to the wall or pillar.

Installing on a level surface

If you install the unit on an inclined surface, the unit may fall or drop and cause injury or damage.

Placing on a stable surface

If you place the unit on an unstable surface, the unit may fall and cause injury or damage.

Fall

Do not hang anything on the unit. The unit may fall from the stand or wall-mount unit,

causing damage or serious injury.

Power-Cord Protection

Do not allow anything to rest on or roll over the power cord, and do not place the unit where the power cord is subject to wear or abuse.

Outdoor use

Do not install this unit outdoors. If the unit is exposed to rain, it may result in fire or electric shock. If the unit is exposed to direct sunlight, the unit may heat up and it may damage the unit.

Vehicle and ceiling

Do not install this unit in a vehicle or hung from the ceiling.

Bumping of the vehicle may cause the unit to fall down and cause injury.

Ship and vessel

Do not install this unit in a ship or vessel. If the unit is exposed to seawater, it may cause fire or damage the unit.

Antennas

Outdoor Antenna Grounding

If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits.

WHEN INSTALLING AN OUTDOOR ANTENNA SYSTEM, EXTREME CARE SHOULD BE TAKEN TO KEEP FROM CONTACTING SUCH POWER LINES OR CIRCUITS AS CONTACT WITH THEM IS ALMOST INVARIABLY FATAL.

Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges.

Section 810 of the National Electrical Code (NEC) in USA and Section 54 of the Canadian Electrical Code in Canada provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

(Continued)

Antenna Grounding According to the National Electrical Code, ANSI/NFPA 70

Antenna lead-in wire

Ground clamps

Antenna discharge uni t

Electric service equipment

NEC: National Electrical Code

(NEC Section 810-20)

Grounding conductors (NEC Section 810-21)

Ground clamps

Power service grounding electrode system (NEC Art 25 0 Part H)

Lightning

For added protection for this TV receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to the receiver due to lightning and power-line surges.

Service

Damage Requiring Service

Unplug the unit from the wall outlet and refer servicing to qualified service personnel under the following conditions:

s When the power cord or plug is damaged

or frayed.

s If liquid has been spilled into the unit.

s If the unit has been exposed to rain or water.

s If the unit has been subject to excessive shock

by being dropped, or the cabinet has been damaged.

Replacement Parts

When replacement parts are required, be sure the service technician certifies in writing that he/she has used replacement parts specified by the manufacturer that have the same characteristics as the original parts.

Unauthorized substitutions may result in fire, electric shock or other hazards.

Safety Check

Upon completion of any service or repairs to the unit, ask the service technician to perform routine safety checks (as specified by the manufacturer) to determine that the unit is in safe operating condition, and to so certify. When the unit reaches the end of its useful life, improper disposal could result in a picture tube implosion. Ask a qualified service technician to dispose of the unit.

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

s If the unit does not operate normally when

following the operating instructions. Adjust only those controls that are specified in the operat i ng instructions. Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to normal operation.

s When the unit exhibits a distinct change in

performance, it indicates a need for service.

Servicing

Do not attempt to service the unit yourself since opening the cabinet may expose you to dangerous voltage or other hazards. Refer all servicing to qualified se rvice personnel.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Contents

Introducing the TV

Setting Up the TV

Welcome...............................................................................................11

Package Contents..........................................................................11

Features.........................................................................................12

Overview .............................................................................................. 15

TV Controls and Connectors..............................................................16

Front panel....................................................... ...... ........................16

Side panel......................................................................................17

Rear panel......................................................................................18

Connecting the Power Cord...............................................................20

Preventing the TV from Toppling Over...........................................21

Bundling the Connecting Cables....................................................22

Basic Connections: Connecting a Cable or Antenna......................23

Cable or Antenna...........................................................................24

Cable Box and Cable.....................................................................25

Cable Box.......................................................................................26

Connecting Optional Equipment .......................................................28

Making Video Connections ............................................................28

About Using S VIDEO................................. ..... ...... ........................29

VCR and Cable..............................................................................30

VCR and Cable Box.......................................................................32

Two VCRs for Tape Editing............................................................34

Satellite Receiver...........................................................................36

Satellite Receiver and VCR............................................................38

DVD Player with Component Video Connectors............................41

DVD Player with S VIDEO and Audio Connectors.........................43

Digital Satellite Receiver with HDMI Connector.............................44

DVD Player or Digital Satellite Receiver via AV Receiver with

CENTER SPEAKER IN Terminals..........................................46

Camcorder .....................................................................................48

Audio Receiver...............................................................................49

Sub Woofer....................................................................................49

Device with an Optical (Digital Audio) Connector..........................50

Using the CONTROL S Feature.....................................................50

Using CableCARD

Activating CableCARD Removing the CableCARD

Setting Up the Channel List ...............................................................53

Using Auto Setup...........................................................................53

™

............................................................................51

™

Service...................................................51

™

..........................................................52

Using the Remote Control

Using the Features

Overview .............................................................................................. 55

Inserting Batteries...............................................................................55

Button Descriptions............................................................................56

Programming the Remote Control.....................................................58

Using Other Equipment with Your Remote Control.........................60

Operating a Cable Box...................................................................60

Operating a Satellite Receiver .......................................................60

Operating a VCR............................................................................61

Operating a DVD Player or DVD Changer.....................................61

Operating a 5.1ch DVD AV System (Sony DAV)...........................62

Operating a DVD/VCR Combo Unit...............................................62

Operating an AV Receiver.............................................................62

Overview .............................................................................................. 63

Watching TV.........................................................................................64

Using the Program Guide...................................................................65

Displaying the Program Guide.......................................................65

Using Additional Program Guide Options ......................................66

Using Wide Screen Mode ...................................................................67

Using Twin View..................................................................................69

Displaying Twin Pictures................................................................69

Activating the Picture .............................................................. ..... ..70

Changing the Picture Size..............................................................71

Using Favorite Channels....................................................................72

Using the Channel Menu................................................................72

Using the Favorite Channels Guide...............................................73

Using the Memory Stick Viewer

About Memory Stick............................................................................75

Features.........................................................................................75

Memory Stick Compatibility............................................................76

Memory Stick Functionality............................................................76

File Compatibility............................................................................77

Trademark Information...................................................................77

Inserting and Removing a Memory Stick..........................................78

Inserting a Memory Stick................................................................78

Inserting the Memory Stick DUO....................................................79

Removing a Memory Stick.............................................................80

Using the Memory Stick Index...........................................................81

Using the Memory Stick Index .......................................................82

Viewing Photos....................................................................................83

Photo Controls ............................................................. ..... ...... .......83

Photo Menu Bar Options......................................................... ..... ..84

Using Zoom and Pan.....................................................................85

Using Rotate ..................................................................................85

Playing Movies ....................................................................................86

Movie Controls...................................... ...... ..... ...... ........................86

Movie Menu Bar Options................................................................87

Memory Stick Index Menu Bar Options.............................................88

Slide Show Menu Options..............................................................88

Contents Menu Options .................................................... .............89

Memory Stick Menu .......................................................................89

Notes on Using Memory Stick Media ................................................90

About DCF File Names..................................................................90

Memory Stick Precautions.............................................................90

Using the Menus

Overview .............................................................................................. 91

Navigating Through Menus................................................................91

Using the Video Menu.........................................................................92

Selecting Video Options.................................................................92

Using the Audio Menu ........................................................................95

Selecting Audio Options.................................................................95

Using the Screen Menu.......................................................................97

Selecting Screen Options...............................................................97

Using the Channel Menu ....................................................................99

Selecting Channel Options.............................................................99

Using the Parental Lock Menu.........................................................101

Selecting Parental Lock Options....................................... ...... .....101

US Models: Selecting Custom Rating Options.............................102

Viewing Blocked Programs..........................................................102

Canadian Models: Selecting Custom Rating Options..................103

Viewing Blocked Programs..........................................................103

Using the Setup Menu.......................................................................104

Selecting Setup Options...............................................................104

Programming Caption Vision .......................................................106

Using the Applications Menu...........................................................107

Selecting Applications Options.....................................................107

Other Information

Overview ............................................................................................109

Glossary.............................................................................................110

Contacting Sony................................................................................111

Troubleshooting................................................................................111

Twin View.....................................................................................111

Remote Control............................................................................112

CableCARD

Channels......................................................................................113

Memory Stick ...............................................................................114

Audio............................................................................................115

Video............................................................................................116

General ........................................................................................117

Specifications....................................................................................118

Optional Accessories............................................................. ...... .....120

Index...................................................................................................121

™

...............................................................................112

Introducing t he TV

Welcome

Thank you for purchasing the Sony Flat Panel Color TV. This manual is to be used with the following models:

s KDE-37XS955 s KDE-42XS955 s KDE-50XS955

Package Contents The package contains the following:

s Flat panel color TV s Remote control (RM-Y1004) and two size AA batteries s AC power cord s AC plug holder s Cable band (1) s Cable band screw (1) s AC cord clamp s Cleaning cloth s Operating Instructions s Qu ick S etup Guide s Warranty Card

These items are all you need to set up and operate the TV in its basic configuration.

Most components (VCRs, DVD players, etc.) come with the necessary cables to connect them. If you want to set up a complex system, you may need to buy extra cables, connectors, etc. Be sure to have these on hand before you start to connect your system.

(Continued)

Features Some of the features that you will enjoy with your new TV include:

s Integrated HDTV: You can watch digital television programs and

enjoy the improved audio/video quality offered by these programs.

Welcome

s Ca bleCARD

encrypted cable channels — without the need for a set-top box — that will enable you to receive not only standard definition but also high definition television. The CableCARD cable TV company, is inserted into the TV’s rear panel CableCARD slot. After the service is activ a ted with you r cable TV compan y, the card replaces the need for a separate set-top box. (Che ck with you r cable TV company about CableCARD availability. For more information about CableCARD see pages 18 and 51.)

s WEGA Engine

source by minimizing the signal deterioration caused by digital-toanalog conversion and stabilizing the signal processing. The WEGA engine features unique Sony technology, including:

• The first step in the digital processing system, Composite Component Processor2 (CCP2), which enhances input signal to noise ratio by chroma decoder digital processing;

• DRC (Digital Reality Creation Enables the digital mapping of any NTSC source (DVD, VHS, DBS, Cable, etc.), to create a picture that is precise and finer in detail, rivaling high definition resolution. Incoming HD signals (1080i) are also bitmapped, utilizing Sony’s proprietary algorithm to provide a crisp and clear picture;

• IFP (Image Format Processor): The Digital Texture Enhancer function of this chip provides the optimal contrast by utilizing a wide dynamic range. This chip also reduces signal noise, by using an improved motion vector algorithm, while maintaining image sharpness.

• New Panel Driver LSI: This drive provides a more realistic color expression by improving the color space of the original signal and color gradation.

s S-master

reproduces the original sound quality while minimizing any sound fragmentation or jitter noise.

s BN Smoother

encoding and decoding process.

s CineMotion

detecting film content and applying a reverse 3/2 pulldown process. Moving pictures will appear clearer and more natural-looking.

™

slot: Provides cable subscribers with access to digitally

™

, which is provided by your

™

service details, limitations, pricing, and

™

: Delivers superb picture quality from any video

) MultiFunction 2 circuitry:

Full Digital Amplifier: Delivers superb clear dialog and

™

: Reduces the block noise caused by digital video

: Provides an optimized display by automatically

™

in this manual,

™

s Wide Screen Mode: Watch conventional 4:3 aspect ratio broadcasts in

wide screen (16:9) mode.

s Favorite Channels: Allows you to preview and select from 16 of your

favorite channels.

s Steady Sound

between programs and commercials.

s Memory Stick

images (JPEG) and movies (MPEG1) with background music (MP3) that are stored on Memory Stick media.

s Component Video Inputs: Offers the best video quality for DVD (480p

and 480i), and digital set-top box (1080i, 720p, 480p and 480i) connections.

s Parental Control: V-Chip technology allows parents to block

unsuitable programming from younger viewers.

s HD MI (High-Definition Multimedia Interface): Provides an

uncompressed, all-digital audio/video interface between this TV and any HDMI-equipped audio/video component, such as a set-top box, DVD player, and A/V receiver. HDMI supports enhanced, or highdefinition video, plus two-channel digital audi o.

: Equalizes volume levels so there is consistent output

Viewer: Allows you t o view on your TV screen digi tal

Welcome

Setting Up the TV

Overview

This chapter includes illustrated instructions for setting up your TV.

Topic Page(s)

TV Controls and Connectors 16-19 Connecting the Power Cord 20-22 Basic Connections: Connecting a Cable or Antenna 23-27 Connecting Optional Equipment

Making Video Connections About Using S VIDEO VCR and Cable VCR and Cable Box Two VCRs for Tape Editing Satellite Receiver Satellite Receiver and VCR DVD Player with Component Video Connectors DVD Player with S VIDEO and Audio Connectors Digital Satellite Receiver with HDMI Connector DVD Player or Digital Satellite Receiver via AV Receiver with CENTER SPEAKER IN Terminals Camcorder Audio Receiver Sub Woofer Device with an Optical (Digital Audio) Connector

Using the CONTROL S Feature Using CableCARD Setting Up the Channel List 53

28 29 30 32 34 36 38 41 43 44

46 48 49 49 50

™

50 51

TV Controls and Connectors

Front panel

Setup

PICTURE OFF TIMER STANDBY POWER

Item Description

1 Speakers

2 PICTURE OFF

3 TIMER LED When lit, indicates one of the timers is set. When the timer

4 STANDBY LED When in standby mode, the LED lights up in red. 5 POWER LED Lights up in green when the TV set is turned on. The LED

6 (IR) Infrared

(Left/Right)

LED

Receiver

Outputs audio signal.

When lit, indicates that the Pictur e Off feature is activated. For details, see page 56.

is set, this LED will remain lit even if the TV set is turned off. For details, see page 107.

does not light up when the main power is turned off. If the LED blinks in red continuously, this may indicate the display unit needs servicing (see “ C ontacting Sony” on page 111).

Receives IR signals from the remote control.

Side panel

Left side

PRO

STD/DUO

VIDEOLR S

VIDEO

)

VIDEO 2 IN

MONO

(

AUDIO

Item Description

1 Memory Stick

indicator

2 Memory Stick

slot

3 VIDEO 2 IN

S VIDEO

When lit, indicates that the Memory Stick is being read. (Do not remove the Mem ory Stick when the indica tor is lit.)

Memory Stick insertion slot. For details, see “Inserting and Removing a Memory Stick” on page 78.

Connects to the S VIDEO OUT jack on your camc order or other video equipment that has S VIDEO. Provides better

Right side

POWER

CHANNEL

VOLUME

TV/VIDEO

picture quality than composite video (4).

4 VIDEO 2 IN

VIDEO/

Connects to the composite A/V output jacks on your camcorder or other video equipment.

L (MONO)AUDIO-R

5 Main POWER Press to turn on and off the main power of the TV. 6 + CHANNEL – Press to scan through channels. To scan quickly through

channels, press and hold down either CHANNEL.

7 + VOLUME – Press to adjust the volume. 8 TV/VIDEO Press repeatedly to cycle through t he video equipment

connected to the TV’s video inputs.

Setup

Rear panel

Setup

For KDE-50XS955

AC IN

OPTICAL OUT

CableCARD

VHF/UHF

R-AUDIO -L

(

MONO

R-AUDIO -L

(

VIDEO IN

VIDEO

)

YPB PR

HD/DVD IN

1080i/720p/480p/480i

VIDEO

)

CENTER SPEAKER IN

180W ( 6 )MAX

Jack Description

1 AC IN Connects the supplied AC power cord. 2 DIGITAL AUDIO

(OPTICAL) OUT

Connect to the optical audio input of a digital audio component that is PCM/Dolby Digital compatible.

(PCM/DOLBY* DIGITAL)

™

3 CableCARD

slot CableCARD™ provides cable subscribers with access to secure, digitally encrypted cable

channels

–without the need for a set-top-box–that will enable you to recei ve not only

standard definition but also high definition television. For more information, see page 51.

CABLE

R-AUDIO -L

AUDIO OUT

(

)

VAR/FIX

CONTROL S

OUT

SUBWOOFER OUT

(

)

VAR

Jack Description

4 VIDEO 6 IN

HDMI IN/R-AUDIO-L

5 VIDEO 1/3 IN

VIDEO/ R-AUDIO-L (MONO)

6 HD/DVD 4/5 IN

(1080i/720p/480p/ 480i)

7 CABLE RF input that connects to your cable signal. 8 VHF/UHF RF input that connects to your VHF/UHF antenna or cable box. 9 VIDEO 1/3 IN

S VIDEO

0 CENTER SPEAKER

IN 180W (6Ω) MAX

qa CONTROL S

IN/OUT

qs SUBWOOFER OUT

(VAR)

qd AUDIO OUT

(VAR/FIX/R/L)

* “Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories.

HDMI (High-Definition Multimedia Interface) provides an uncompressed, all-digital audio/video interface between this TV a nd any HDMI-equipped audio/video component, such as a set-top box, DVD player, and A/V receiver. HDMI supports enhanced, or highdefinition video, plus two-channel digital audio.

Connect to the composite A/V output jacks on your VCR or other video component. A third composite A/V input jack (VIDEO 2) is located on the left side panel of the TV. These video connectio ns provide better picture quality than the VHF/UHF (8) connections.

Connect to your DVD player’s or digital set-top box’s component video (Y, P audio (L/R) jacks. Component v ideo pro vides bet ter picture quality th an the S VIDEO (9), the VHF/UHF (8) or the composite vi deo (5) connections .

Connects to the S VIDEO OUT jack of your VCR or other video equipment that has S VIDEO. S VIDEO provides better picture quality than either composite video (5) or VHF/UHF (8) connections .

Connect the center output terminals of Dolby Pro Logic* system decoder amplifier. You can use the TV speakers as a center speaker.

Allows the TV to receive (IN) and send (OUT) remot e control signals to other Sony infrared-contr olled audio or video equipment that has the CONTROL S function.

Connects to the input jack of your woofer.

Connects to the left and right audio input jacks of your audio or video equipment. You can use these outputs to listen to your TV’s audio through your stereo system.

B, PR) and

Setup

Connecting the Power Cord

1 Connect the power cord to the AC IN connector of the TV. 2 Secure the AC power plug to the display’s AC IN jack.

Setup

Complete other connections prior to connecting the power cord.

AC IN (Power supply input) jack of the display

AC power cord (supplied)

AC plug holder (supplied)

1 Attach the AC plug holder

(supplied) to the AC power cord (supplied).

2 Clip on to the AC IN

jack until you hear clicking.

When you unplug the AC power cord, drag the holder down by pushing both sides of the holder, then pull out the plug.

3 Connect the other end of the AC power cord (supplied) to a wall outlet.

Tighten the screw slowly until the screw is stabilized.

AC IN

AC power cord (supplied)

Be sure to use the supplied AC power cords. When connecting optional components, do n ot connect the A C

power cords to wall outlets until you have completed making all connections.

Do not use damaged cabl es, suc h as cable s whose conn ector s are deformed.

Preventing the TV from Toppling Over

WARNING

Be sure to take measures to prevent stand from toppling over. If you fail to do so, the TV may topple over and cause injury. Anchor the TV to a wall, pillar, etc., to prevent it from toppling over.

Prepare a commercially available strong rope or chain and wall anchor bracket beforehand.

Setup

After connections with antennas and other equipment ar e completed, be sure to attach a sturdy strong rope or chain securely to each clamp screw, and attach it to a wall or pillar.

Rear of TV

Clamp screw

Bundling the Connecting Cables

Setup

You can bundle the connecting cables using the supplied cord clamp with a cable band at the rear of the TV.

1 Bundle the connecting cables.

Rear of TV

Cord clamp

Cable band

2 Attach the supplied cord clamp for the AC power cord. 3 Remove the cable cover.

One side of the cable cover is secured by screws.

4 Store the connecting cables. 5 Secure the cord clamp and replace the cable cover.

Basic Connections: Connecting a Cable or Antenna

The way in which you will connect your TV varies, depending on how your home receives a signal (cable, cable box, antenna) and whether or not you plan to connect a VCR.

If You Are Connecting See Page

Cable or Antenna

s No cable box or VCR

Cable Box and Cable

s Cable box unscrambles only some channels

(usually premium channels)

s No VCR

Cable Box

s Cable box unscrambles all channels s No VCR

If you are connecting a VCR

s See the connections described on pages 30 and 32.

Setup

Cable or Antenna For best results, use this con nection i f y ou ar e conn ecting a cabl e or a n

antenna and you:

s Do not need a cable box to unscramble channels. (If you have a cable

box, see page 26.)

s Do not intend to connect a VCR. (If you have a VCR, see pages 30 and

32.)

For antenna connection, use the 75-ohm coaxial cable (not supplied) .

Cable Type Connect As Shown

Setup

VHF Only or combined VHF/UHF

75-ohm coaxial cable

VHF/UHF

Cable

Note on Using This Connection

To Do This ... Do This ...

Switch the TV’s input between the cable and antenna

Press ANT to switch back and forth between the TV’s VHF/UHF and CABLE inputs.

75-ohm coaxial cable

When using an indoor antenna, such as rabbit-ear or dipoleantenna, keep the antenna away from the display unit. If not, noise may appear on the screen.

CABLE

Cable Box and Cable For best results, use this connection if:

z Before connecting a

cable box, See “Using CableCARD

™

” on

page 51.

s Your cable company scrambles some channels, such as premium

channels (which requires you to use a cable b ox) , but does not scramble all channels.

s You do not have a VCR. (If you have a VCR, see pages 30 and 32.)

With this connection you can:

s Use the remote control to change channels coming through the cable

box to the TV’s VHF/UHF input jack. (You must first program the remote control for your specific cable box; see “Programming the Remote Control” on page 58.)

s Use the remote control to change channels coming directly into the TV’s

CABLE input. (The TV’s tuner provides a better signal than the cable box.)

Setup

Coaxial cable

CATV cable

Splitter

75-ohm coaxial cable

About Using This Connection with Dual Picture (Twin View, etc.) Features

Coaxial cable

IN OUT

Cable Box

VHF/UHF

Rear of TV

CABLE

With this connection, you can use all the dual picture features for unscrambled channels coming directly into the TV’s CABLE input jack.

Notes on Using This Connection

To Do This ... Do This ...

Use the cable box Tune the TV to the channel the cable box is set to (usually channel 3 or 4) and the n

use the cable box to switch channels.

Set up the remote control to

Program the remote control. See “Pro gramming the Remote Control” on page 58.

operate the cable box Activate the remot e cont rol to

Press SAT/CABLE (FUNCTION).

operate the cable box Prevent the accidental switching

of TV channels

When using the ca ble box, you need the TV to stay on the channel the cable box is set to (usually channe l 3 o r 4). You can use the TV’s Channel Fix feature to lock in a specific channel. For details, see “Using the Channel Menu” on page 99.

the TV’s input between

Switch the cable box and cable

Press ANT to switch back and forth between the TV’s VHF/UHF (scrambled channels) and CAB LE (unscrambled) inputs.

Do not leave the display indication of the cable box turned on.

Cable Box For best results, use this connection if:

z Before connecting a

cable box, See “Using CableCARD page 51.

™

” on

s Your cable compan y scrambles all channels, which requires you to use a

cable box.

s You do not have a VCR. (If you have a VCR, see pages 30 and 32.)

With this connection you can:

s Use the remote control to change channels coming through the cable

box to the TV’s VHF/UHF jack. (You must first program the remote control for your specific cable box, see page 58.)

Setup

About Using This Connection with Dual Picture (Twin View, etc.) Features

With this connection, all channels come into the TV through your cable box and only one unscrambled signal is sent to the TV, so you cannot use the dual picture features. If some of your channels are scrambled, but others are not, consider using the “Cable Box and Cable” connecti on on page 25 instead.

To connect the cable box

1 Connect the CATV cable to the cable box’s input jack. 2 Use the 75-ohm coaxial cable (not supplied) to connect the cable box’s

output jack to the TV’s VHF/UHF jack.

3 Run the Auto Setup program, as described in “Setting Up the Channel

List” on page 53.

CATV cable

75-ohm coaxial cable

Rear of TV

VHF/UHF

OUT

Cable Box

Notes on Using This Connection

To Do This ... Do This ...

Use the cable box Tune the TV to the channel the cable box is set to (usually channel 3 or 4) and the n

use the cable box to switch channels.

Set up the remote control to operate the cable box

Activate the remot e cont rol to operate the cable box

Prevent the accidental switching of TV channels

Program the remote control. See “Programming the Remote Control” on page 58.

Press SAT/CABLE (FUNCTION).

Do not leave the display indication of the cable box turned on.

Setup

Connecting Optional Equipment

Use the directions in this section to connect the following optional equipment:

If You Are Connecting See Page

About Using S VIDEO 29 VCR and Cable 30 VCR and Cable Box 32 Two VCRs for Tape Editing 34 Satellite Receiver 36 Satellite Receiver and VCR 38

Setup

DVD Player with Component Video Connectors 41 DVD Player with S VIDEO and Audio Connectors 43 Digital Satellite Receiver with HDMI Connector 44 DVD Player or Digital Satellite Receiver via AV

Receiver with CENTER SPEAKER IN Terminals 46 Camcorder 48 Audio Receiver 49 Sub Woofer 49 Device with an Optical (Digital Audio) Connector 50 Using the CONTROL S Feature 50

Making Video Connections

Your TV includes several types of video inputs. When connecting your TV, use the inputs that are available on your components that provide the best video performance, as described below.

Best Video Performance

Connector type

HDMI (High-Definition Multimedia Interface)

Component video

YPB PR

S VIDEO Composite video RF/Coaxial

+ 97 hidden pages