To reduce fire or shock hazard, do
not expose the unit to rain or
moisture.
Do not expose the batteries to
excessive heat such as sunshine,
fire or the like.
This symbol is intended to alert
the user to the presence of
uninsulated “dangerous
voltage” within the product’s
enclosure that may be of
sufficient magnitude to
constitute a risk of electric
shock to persons.
This symbol is intended to alert
the user to the presence of
important operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
IMPORTANT
SAFEGUARDS
For your protection, please read these safety
instructions completely before operating
the appliance, and keep this manual for
future reference.
Carefully observe all warnings, precautions
and instructions on the appliance, or the one
described in the operating instructions and
adhere to them.
Use
Power Sources
This set should be operated only from the type of
power source indicated on the marking label. If
you are not sure of the type of electrical power
supplied to your home, consult your dealer or
local power company. For those sets designed to
operate from battery power, or other sources, refer
to the operating instructions.
Polarization
This set may be equipped with a polarized ac
power cord plug (a plug having one blade wider
than the other).
This plug will fit into the power outlet only one
way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing
the plug. If the plug should still fail to fit, contact
your electrician to have a suitable outlet installed.
Do not defeat the safety purpose of the polarized
plug by forcing it in.
Overloading
Do not overload wall outlets, extension cords or
convenience receptacles beyond their capacity,
since this can result in fire or electric shock.
Object and Liquid Entry
Never push objects of any kind into the set
through openings as they may touch dangerous
voltage points or short out parts that could result
in a fire or electric shock. Never spill liquid of any
kind on the set.
Attachments
Do not use attachments not recommended by the
manufacturer, as they may cause hazards.
US
2
Cleaning
Unplug the set from the wall outlet before
cleaning or polishing it. Do not use liquid cleaners
or aerosol cleaners. Use a cloth lightly dampened
with water for cleaning the exterior of the set.
Installation
Water and Moisture
Do not use power-line operated sets near water –
for example, near a bathtub, washbowl, kitchen
sink, or laundry tub, in a wet basement, or near a
swimming pool, etc.
Power-Cord Protection
Route the power cord so that it is not likely to be
walked on or pinched by items placed upon or
against them, paying particular attention to the
plugs, receptacles, and the point where the cord
exits from the appliance.
Accessories
Do not place the set on an unstable cart, stand,
tripod, bracket, or table. The set may fall, causing
serious injury to a child or an adult, and serious
damage to the set. Use only a cart, stand, tripod,
bracket, or table recommended by the
manufacturer.
Ventilation
The slots and openings in the cabinet are provided
for necessary ventilation. To ensure reliable
operation of the set, and to protect it from
overheating, these slots and openings must never
be blocked or covered.
– Never cover the slots and openings with a cloth
or other materials.
– Never block the slots and openings by placing
the set on a bed, sofa, rug, or other similar
surface.
– Never place the set in a confined space, such as
a bookcase, or built-in cabinet, unless proper
ventilation is provided.
– Do not place the set near or over a radiator or
heat register, or where it is exposed to direct
sunlight.
Lightning
For added protection for this set during a lightning
storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system.
This will prevent damage to the set due to
lightning and power-line surges.
Service
Damage Requiring Service
Unplug the set from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
– When the power cord or plug is damaged or
frayed.
– If liquid has been spilled or objects have fallen
into the set.
– If the set has been exposed to rain or water.
– If the set has been subject to excessive shock by
being dropped, or the cabinet has been
damaged.
– If the set does not operate normally when
following the operating instructions. Adjust
only those controls that are specified in the
operating instructions. Improper adjustment of
other controls may result in damage and will
often require extensive work by a qualified
technician to restore the set to normal operation.
– When the set exhibits a distinct change in
performance – this indicates a need for service.
Servicing
Do not attempt to service the set yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
Replacement parts
When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacturer that have the same
characteristics as the original parts.
Unauthorized substitutions may result in fire,
electric shock, or other hazards.
Safety Check
Upon completion of any service or repairs to the
set, ask the service technician to perform routine
safety checks (as specified by the manufacturer)
to determine that the set is in safe operating
condition.
US
3
Read this first
Before operating the unit, please read this
manual thoroughly, and retain it for future
reference.
CAUTION
Replace the battery with the
specified type only. Otherwise, fire
or injury may result.
For customers in the U.S.A. and
CANADA
RECYCLING LITHIUM-ION BATTERIES
Lithium-Ion batteries are recyclable.
You can help preserve our
environment by returning your
used rechargeable batteries to the
collection and recycling location
nearest you.
For more information regarding
recycling of rechargeable batteries, call toll free 1800-822- 8837, or visit http://www.rbrc.org/
Caution: Do not handle damaged or leaking
Lithium-Ion batteries.
Owner’s Record
The model and serial numbers are located on the
bottom. Record the serial number in the space
provided below. Refer to these numbers whenever
you call your Sony dealer regarding this product.
Model No. HDRSerial No.
Model No. ACSerial No.
Battery pack and “Memory Stick PRO
Duo”
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
This Class B digital apparatus complies with
Canadian ICES-003.
US
4
For customers in the U.S.A.
If you have any questions about this
product, you may call:
Sony Customer Information Center 1-800-
222-SONY (7669).
The number below is for the FCC related
matters only.
Regulatory Information
Declaration of Conformity
Trade Name: SONY
Model No.: HDR-TG1
Responsible Party: Sony Electronics Inc.
Address: 16530 Via Esprillo, San Diego, CA
92127 U.S.A.
Telephone number: 858-942-2230
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired operation.
Notes
HDR-TG1 is to be used with the Handycam
Station Model DCRA-C230 and AC
Adaptor Model AC-L200/L200B.
CAUTION
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate this
equipment.
Note
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment
and receiver.
– Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
– Consult the dealer or an experienced radio/TV
technician for help.
The supplied interface cable must be used with t he
equipment in order to comply with the limits for a
digital device pursuant to Subpart B of Part 15 of
FCC Rules.
For the State of California, USA only
Perchlorate Material - special handling may
apply, See
Types of “Memory Stick” you can use
with your camcorder
• For recording movies, it is recommended that
you use a “Memory Stick PRO Duo” of 1 GB or
larger marked with:
– (“Memory Stick
PRO Duo”)*
– (“Memory Stick
PRO-HG Duo”)
* Marked with Mark2 or not, either can be used.
• A “Memory Stick PRO Duo” of up to 16 GB
has been confirmed to operate correctly with
this camcorder.
• See page 15 for the recordable time of a
“Memory Stick PRO Duo.”
• “Memory Stick PRO Duo” and “Memory Stick
PRO-HG Duo” are both called as “Memory
Stick PRO Duo” in this manual.
Using the camcorder
• The camcorder is not dustproofed, dripproofed
or waterproofed. See “Precautions” (p. 33).
• Do not do any of the following when the
(Movie)/(Still) mode lamps (p. 11), the
access lamp (p. 13) or the QUICK ON lamp
(p. 8) is lit or flashing.
Otherwise, the “Memory Stick PRO Duo” may
be damaged, recorded images may be lost or
other malfunctions could occur.
– Eject the “Memory Stick PRO Duo”
– Remove the battery pack or AC Adaptor from
the camcorder.
– Apply mechanical shock or vibration to the
camcorder.
• If you close the LCD panel when your
camcorder is connected to other devices with
the USB cable, the recorded images may be lost.
• When inserting or ejecting the “Memory Stick
PRO Duo,” be careful so that the “Memory
Stick PRO Duo” does not pop out and drop
(p. 13).
• When connecting your camcorder to another
device with a cable, be sure to insert the
connector plug in the correct way. Pushing the
plug forcibly into the terminal will damage the
terminal and may result in a malfunction of your
camcorder.
• If you repeat recording/deleting images for a
long time, fragmentation of data occurs on the
media. Images cannot be saved or recorded. In
such a case, save your images on some type of
US
• The LCD screen is manufactured using
On recording
• Before starting to record, test the recording
• Compensation for the contents of recordings
• TV color systems differ depending on the
• Television programs, films, video tapes, and
On playing back recorded images on
other devices
• Your camcorder is compatible with MPEG-4
Save all your recorded image data
• To prevent your image data from being lost,
• It is recommended that you save your image
6
external media first, and then perform [MEDIA
FORMAT] (p. 25).
extremely high-precision technology, so over
99.99% of the pixels are operational for
effective use. However, there may be some tiny
black points and/or bright points (white, red,
blue, or green in color) that appear constantly on
the LCD screen. These points are normal results
of the manufacturing process and do not affect
the recording in any way.
function to make sure the image and sound are
recorded without any problems.
cannot be provided, even if recording or
playback is not possible due to a malfunction of
the camcorder, recording media, etc.
country/region. To view your recordings on a
TV, you need an NTSC system-based TV.
other materials may be copyrighted.
Unauthorized recording of such materials may
be contrary to the copyright laws.
AVC/H.264 High Profile for HD (high
definition) image quality recording. Therefore,
you cannot play back images recorded with HD
(high definition) image quality on your
camcorder with the following devices;
– Other AVCHD format compatible devices
which are not compatible with High Profile
– Devices which are not compatible with the
AVCHD format
save all your recorded images on other media. It
is recommended that you save the image data on
a disc such as DVD-R using your computer, etc.
Also, you can save your image data using a
VCR, or a DVD/HDD recorder (p. 24).
data periodically, after recording.
Table of Contents
When the camcorder is connected to a
computer
• Do not try to format the “Memory Stick PRO
Duo” in the camcorder using a computer. If you
do so, your camcorder may not operate
correctly.
About language setting
• The on-screen displays in each local language are
used for illustrating the operating procedures.
Change the screen language before using your
camcorder if necessary (p. 12).
About this manual
• The images of the LCD screen used in this
manual for illustration purposes are captured
using a digital still camera, and therefore may
appear different from the actual images of the
LCD screen.
• Design and specifications of your camcorder
and accessories are subject to change without
notice.
• The screenshots are from Windows Vista. The
scenes may vary depending on the operating
system of the computer.
• Refer also to “Handycam Handbook” (PDF) and
“PMB Guide.”
IMPORTANT SAFEGUARDS ..........2
Read this first...................................4
Getting Started
Step 1: Charging the battery pack ...8
Step 2: Turning the power on, and
You can charge the “InfoLITHIUM”
battery pack NP-FH50 after attaching
it to your camcorder.
b Notes
• You cannot attach any “InfoLITHIUM” battery
pack other than NP-FH50 to your camcorder.
1 Connect the AC Adaptor to the
DC IN jack on the Handycam
Station.
Be sure that the v mark on the DC plug
is facing up.
2 Connect the power cord (mains
lead) to the AC Adaptor and the
wall outlet (wall socket).
lamp
AC Adaptor
4 Insert the battery.
1 Open the battery/Memory Stick Duo
cover.
2 Insert the battery pack all the way in
until it clicks.
3 Close the battery/Memory Stick Duo
cover.
5 Place the camcorder on the
Handycam Station as shown
above, and insert it into the
Handycam Station securely, all
the way to the bottom.
The /CHG (charge) lamp lights up and
charging starts. The /CHG (charge)
lamp turns off when the battery pack is
fully charged. Remove the camcorder
from the Handycam Station.
Battery pack
Power cord
(Mains lead)
To the wall outlet
(wall socket)
3 Make sure that the LCD panel is
closed.
US
8
b Notes
• You cannot charge the battery pack while the
QUICK ON lamp is flashing. When the QUICK
ON lamp is flashing, press POWER to turn off
your camcorder. Make sure the QUICK ON
lamp is not flashing before charging the battery
pack.
To remove the battery pack
Turn off your camcorder and open the
battery/Memory Stick Duo cover.
Slide the battery eject lever.
Be sure not to drop the battery pack.
Battery eject lever
b Notes
• When you remove the battery pack or
disconnect the AC Adaptor, make sure that the
(Movie) lamp/ (Still) lamp (p. 11)/
access lamp (p. 13)/QUICK ON lamp are turned
off.
To charge the battery pack using only
the AC Adaptor
Close the LCD panel with your camcorder
turns off, then connect the AC Adaptor to
the DC IN jack on your camcorder.
DC IN jack
Open the jack cover.
DC plug
With the v mark
on the bottom
Available running time for the
supplied battery pack
Charging time:
Approximate time (min.) required when
you fully charge a completely exhausted
battery pack.
Recording/Playback time:
Approximate time (min.) available when
you use a fully charged battery pack.
“HD” stands for high definition image
quality, and “SD” stands for standard image
quality.
(Unit:min.)
HDSD
Charging time135
Recording time*
Continuous recording
time
Typical recording
time*
Playback time*
*1[REC MODE]: SP
2
*
When the LCD backlight is on.
3
Typical recording time shows the time when
*
you repeat recording start/stop, turning the
power on/off and zooming.
1*2
95120
3
2
4560
130145
Getting Started
US
9
On the battery pack
• When you remove the battery pack, turn off
your camcorder, and turn off the (Movie)
lamp/ (Still) lamp (p. 11)/access lamp
(p. 13)/QUICK ON lamp.
• The power will not be supplied from the battery
as long as the AC Adaptor is connected to the
DC IN jack of your camcorder or the Handycam
Station, even when the power cord (mains lead)
is disconnected from the wall outlet (wall
socket).
On the charging/recording/playback time
• Times measured when using the camcorder at
25°C (77°F) (10°C to 30°C (50°F to 86°F) is
recommended).
• The available recording and playback time will
be shorter when you use your camcorder in low
temperatures.
• The available recording and playback time will
be shorter depending on the conditions under
which you use your camcorder.
On the AC Adaptor
• Use the nearby wall outlet (wall socket) when
using the AC Adaptor. Disconnect the AC
Adaptor from the wall outlet (wall socket)
immediately if any malfunction occurs while
using your camcorder.
• Do not use the AC Adaptor placed in a narrow
space, such as between a wall and furniture.
• Do not short-circuit the DC plug of the AC
Adaptor or battery terminal with any metallic
objects. This may cause a malfunction.
• Even if your camcorder is turned off, AC power
source (mains) is still supplied to it while
connected to the wall outlet (wall socket) via the
AC Adaptor.
On using abroad
• You can use your camcorder in any countries/
regions using the AC Adaptor supplied with
your camcorder. Also, you can charge the
battery pack.
Use a commercially available AC plug adaptor
[a], if necessary, depending on the design of the
wall outlet (wall socket) [b].
AC-L200/L200B[a][b]
See “Handycam Handbook” (PDF) for details.
US
10
Step 2: Turning the power on, and setting the
date and time
When using the camcorder for
the first time, the [CLOCK
SET] screen appears on the
LCD screen.
(HOME)
Touch the button on the LCD screen. (Movie) / (Still)
1 Open the LCD panel.
Your camcorder turns on.
To turn on your camcorder when the
LCD panel is opened, close it and open
it again, or press POWER with the LCD
panel opened.
To adjust the LCD panel, open the LCD
panel 90 degrees to the camcorder (1),
then rotate it to the best angle to record
or play (2). You can rotate the LCD
panel 270 degrees to the lens side (2)
to record in mirror mode.
190 degrees
to the
camcorder
POWER button
select switch
2270 degrees (max.)
2 Slide the (Movie)/ (Still)
select switch repeatedly in the
direction of the arrow until the
respective lamp lights up.
(Movie): To record movies
(Still): To record still images
Go to step 4 when you turn on your
camcorder for the first time.
• When you turn on (Still) lamp, the
screen aspect ratio is changed to 4:3
automatically (the default setting).
Getting Started
US
11
3 Touch (HOME) t
(SETTINGS) t [CLOCK/
LANG] t [CLOCK SET].
4 Select the desired geographical
area with /, then touch
[NEXT].
5 Set [DST SET] or [SUMMERTIME],
[Y] (year), [M] (month), [D] (day),
hour and minute, then touch .
The clock starts.
To turn off the power
When recording standby/recording mode,
close the LCD panel, then press POWER.
Otherwise, close the LCD panel or press
POWER.
z Tips
• The date and time do not appear during
recording, but they are automatically recorded
on the “Memory Stick PRO Duo,” and can be
displayed during playback.
• You can turn off the operation beeps by
touching (HOME) t (SETTINGS) t [SOUND/DISP SET] t [BEEP] t [OFF].
• When you close the LCD panel during standby/
recording, the QUICK ON lamp starts flashing
and your camcorder goes to sleep mode. If
[QUICK ON STBY] is set to [OFF] on the
HOME MENU (p. 23), closing the LCD panel
makes your camcorder turn off.
Changing the language setting
You can change the on-screen displays to
show messages in a specified language.
Touch (HOME) t (SETTINGS) t [CLOCK/LANG] t
[LANGUAGE SET], then select the
desired language.
12
US
Step 3: Inserting a “Memory Stick PRO Duo”
Access lamp
If you insert a new “Memory Stick
PRO Duo,” the [Create a new Image
Database File.] screen appears.
See page 6 on the “Memory Stick” you can
use with your camcorder.
1 Insert the “Memory Stick PRO
Duo.”
1 Open the battery/Memory Stick Duo
cover.
2 Insert the “Memory Stick PRO Duo”
all the way in until it clicks.
3 Close the battery/Memory Stick Duo
cover.
2 Open the LCD panel and turn on
the (Movie) lamp.
3 On the [Create a new Image
Database File.] screen, touch
[YES].
b Notes
• Do not do any of the following when the
(Movie) /(Still) mode lamps (p. 11), the
access lamp or the QUICK ON lamp (p. 8) is lit
or flashing.
Otherwise, the media may be damaged,
recorded images may be lost or other
malfunctions could occur.
– Eject the “Memory Stick PRO Duo” from the
camcorder
– Remove the battery pack or AC Adaptor
– Shake or knock your camcorder
• Do not open the battery/Memory Stick Duo
cover during recording.
• If you force the “Memory Stick PRO Duo” into
the slot in the wrong direction, the “Memory
Stick PRO Duo,” the Memory Stick Duo slot, or
image data may be damaged.
• If [Failed to create a new Image Database File.
It may be possible that there is not enough free
space.] is displayed in step 3, format the
“Memory Stick PRO Duo” (p. 25). Note that
formatting will delete all data recorded on the
“Memory Stick PRO Duo.”
Getting Started
To eject a “Memory Stick PRO Duo”
Open the battery/Memory Stick Duo cover,
lightly push the “Memory Stick PRO Duo”
in once.
US
13
Recording/Playback
Recording
START/STOP A
(Movie) / (Still)
select switch C
[STBY] t [REC]
PHOTO B
Flashing t Lights up
1 Open the LCD panel.
2 Slide the (Movie)/ (Still) select switch C until the respective lamp
lights up.
• (Movie): To record movies
• (Still): To record still images
3 Start recording.
MoviesStill Images
Press START/STOP A.
To stop recording, press START/STOP A
again.
• See “Handycam Handbook” (PDF) to display
the image of SD (standard definition) image
quality.
b Notes
• If you close the LCD panel during recording, the recording will be stopped.
US
14
Press PHOTO B lightly to adjust the
focus A (a beep sounds), then press
it fully B (a shutter click sounds).
appears beside . When
disappears, the image has been recorded.
z Tips
• You can check the free “Memory Stick PRO
Duo” space by touching (HOME) t
(MANAGE MEDIA) t [MEDIA INFO].
• You can capture still images by pressing
PHOTO B during movie recording.
• When a movie file exceeds 2 GB, the next
movie file is created automatically.
• The maximum recordable time of Sony
“Memory Stick PRO Duo” is as follows with
recording mode [HD SP] (the default setting);
• When measuring “Memory Stick PRO Duo”
capacity, 1 GB equals 1 billion bytes, a portion
of which is used for data management.
• Check the number of recordable still images on
the LCD screen of your camcorder (p. 20).
• You can capture still images from recorded
movies. See “Handycam Handbook” (PDF) for
details.
Recording/Playback
US
15
Playback
(VIEW IMAGES)
1 Goes to the (Film Roll Index) screen
2 Goes to the (Face Index) screen
3 Goes to (HOME)
4 Previous 6 images
5 Next 6 images
6 Returns to the recording screen
7 Displays movies with HD (high definition)
image quality*
8 Displays still images
9 Searches for images by date
0 (OPTION)
* appears when you select the movie with
SD (standard definition) image quality.
1 Open the LCD panel to turn on your camcorder.
2 Touch (VIEW IMAGES).
The VISUAL INDEX screen appears on the LCD screen (It may take some time to display
the thumbnails).
3 Start playback.
Movies
Touch the or tab, then select
the desired movie to play back.
Beginning of the
scene/previous
scene
Stop (go to the
INDEX screen)
Toggles Play
or Pause as
you touchNext scene
Reverse/Forward
OPTION
Still Images
Touch the tab, then select the
desired still image to play back.
Slide show
Previous/NextGo to the VISUAL
INDEX screen
OPTION
16
US
To adjust the sound volume of movies
When playing back a movie, touch
(OPTION) t tab t [VOLUME],
then adjust the volume with /.
z Tips
• On the VISUAL INDEX screen, i appears
with the image on the tab that was most recently
played back/recorded (B for the still image).
When you touch a movie marked with i, you
can play it back from the point it was previously
stopped.
Open the jack cover.
A/V Remote
Connector
Playing the image on a TV
Connection methods and quality of the
image (HD (high definition)/SD (standard
definition)) viewed on the TV screen differ
depending on what type of TV is connected,
and the connectors used.
Use the supplied AC Adaptor as the power
source (p. 8).
Refer also to the instruction manuals
supplied with the device to be connected.
b Notes
• When recording, set [X.V.COLOR] to [ON] to
play back on an x.v.Color-compliant TV. Some
settings may need to be adjusted on the TV
when playing back. Refer to the instruction
manual of your TV for details.
Operation flow
Switch the input on the TV to the
connected jack.
Refer to the instruction manuals of the
TV.
r
Connect your camcorder and TV
referring to [TV CONNECT Guide].
Touch (HOME) t (OTHERS)
t [TV CONNECT Guide].
r
Make the required output settings
on your camcorder.
Open the jack cover.
Handycam
Station
b Notes
• When the A/V connecting cable is used to
output images, images are output with SD
(standard definition) image quality.
• Your camcorder and the Handycam Station are
equipped with A/V Remote Connector or A/V
OUT jack. Connect the A/V connecting cable or
component A/V cable either to the Handycam
Station or to your camcorder. If you connect A/
V connecting cables or component A/V cable to
both the Handycam Station and your camcorder
at the same time, image disturbance may occur.
Recording/Playback
US
17
Name and functions of each part
Buttons, jacks, etc., which are not explained
in other chapters, are explained here.
Handycam Station
Recording/Playback
A Flash
The flash will flash automatically
depending on recording conditions in the
default setting.
Touch (HOME) t (SETTINGS) t [PHOTO SETTINGS] t [FLASH
MODE] to change the setting.
B Speaker
C QUICK ON lamp
Flashes during sleep mode. When you open
the LCD panel while the QUICK ON lamp
is flashing, you can start recording in about
1 second (QUICK ON).
The flashing stops and the power turns off
automatically if you do not operate your
camcorder for a certain period during sleep
mode ([QUICK ON STBY], p. 23).
D Power zoom lever
Move the power zoom lever slightly for a
slower zoom. Move it further for a faster
zoom.
You can magnify still images from about
1.1 to 5 times the original size (Playback
zoom).
• When you touch the screen during playback
zoom, the point you touched will be displayed in
the center of the LCD screen.
E RESET button
Press RESET to initialize all the settings
including the clock setting.
F EASY button
Press EASY to display and most of
the settings are set automatically for easy
recording/playback. To cancel, press EASY
again.
18
US
G DISP/BATT INFO button
You can switch the screen display when
you press DISP/BATT INFO while the
power is on.
You can check the remaining battery when
you press it after you open the LCD panel
and press POWER to turn off your
camcorder.
H Built-in microphone
Sound picked up by the internal
microphone is converted to 5.1ch surround
sound and recorded.
I Access lamp
When the access lamp is lit or flashing,
your camcorder is writing/reading data on
the “Memory Stick PRO Duo.”
J POWER button
Press POWER to turn on your camcorder.
When you press it while the power is on,
your camcorder turns off.
• When you press POWER to turn on your
camcorder while the LCD panel is closed, your
camcorder goes to sleep mode. When you press
POWER while sleep mode, your camcorder
turns off.
M Tripod receptacle (Bottom surface)
Attach a tripod (optional) to the tripod
receptacle using a tripod screw (optional:
the length of the screw must be less than 5.5
mm (7/32 in.)).
O Hook for wrist strap (Bottom surface)
Attach the strap and place your hand
through the loop to prevent the camcorder
from damage by being dropped.
Connecting to other devices
K HDMI OUT jack
Connect with the HDMI cable (optional).
L A/V Remote Connector/A/V OUT
jack
Connect with the component A/V cable or
A/V connecting cable.
N Interface connector (Bottom surface)
Connect your camcorder and the Handycam
Station or the Dedicated USB Terminal
Adaptor.
By attaching the Dedicated USB Terminal
Adaptor, you can connect the USB cable to
your camcorder without using the
Handycam Station.
P (DISC BURN) button
Create a disc by connecting the camcorder
to a computer, etc. For details, see “PMB
Guide” (p. 29).
Q Interface connector (Handycam
Station)
Connect to the interface connector on your
camcorder when you attach your camcorder
to the Handycam Station.
R (USB) jack
Connect with the USB cable.
Recording/Playback
US
19
Indicators displayed during recording/playback
Recording movies
Recording still images
Viewing movies
Viewing still images
A HOME button
B Remaining battery (approx.)
C Recording status ([STBY] (standby) or
[REC] (recording))
D Recording quality (HD/SD) and
Recording mode (FH/HQ/SP/LP)
E Media
F Counter (hour/minute/second)
G Recording remaining time
H OPTION button
I FACE DETECTION
J VIEW IMAGES button
K Face Index set
L 5.1ch surround recording
M Image size
N Approximate number of recordable still
images and media/During still image
recording
O Recording folder
P Return button
Q Playback mode
R Currently playing movie number/
Number of total recorded movies
S Previous/Next button
T Video operation buttons
U Currently playing still image number/
Number of total recorded still images
V Playback folder
W Slide show button
X Data file name
Y VISUAL INDEX button
20
US
Indicators on the LCD screens
Following indicators appear during
recording/playback to indicate the settings
of your camcorder.
Upper leftUpper right
Bottom
Upper left
IndicatorMeaning
Flash, REDEYE
Center
IndicatorMeaning
E
Center
AUDIO MODE
Self-timer recording
REDUC
MICREF LEVEL low
WIDE SELECT
BLT-IN ZOOM MIC
IMAGE SIZE
Continuous slide show
Color Slow Shutter
PictBridge connecting
Warning
Upper right
IndicatorMeaning
FADER
LCD backlight off
Bottom
IndicatorMeaning
Picture effect
Digital effect
9Manual focus
n White balance
z Tips
• Indicators and their positions are approximate
and differ from what you actually see. See
“Handycam Handbook” (PDF) for details.
• The recording date and time are recorded
automatically on the “Memory Stick PRO Duo.”
They are not displayed while recording.
However, you can check them as [
] during playback.
CODE
SCENE SELECTION
SteadyShot off
EXPOSURE/
SPOT METER
TELE MACRO
ZEBRA
X.V.COLOR
Face Index
FACE DETECTION
DATA
Recording/Playback
US
21
Loading...
+ 47 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.