Sony HCD-G1 Service Manual

HCD-G1
SERVICE MANUAL
HCD-G1 is the tuner, deck, CD and amplifier section in LBT-G1/G1S.
Model Name Using Similar Mechanism NEW
CD
SECTION
TAPE
DECK
SECTION
CD Mechanism Type CX3 Base Unit Type KSM-213BCM Optical Pick-up Type KSS-213B/S-N Model Name Using Similar Mechanism HCD-H100
Tape Transport Mechanism Type
DECK-A DECK-B
AEP Model
UK Model
E Model
TK20FX-SW943-800 TK20FX-SW943-800
SPECIFICATIONS
COMPACT DISC DECK RECEIVER
— Continued on next page —
MICROFILM
— 1 —
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous ra­diation exposure.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C during repairing.
• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or unsoldering.
Laser component in this product is capable of emitting radiation exceeding the limit for Class 1.
This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PROD­UCT MARKING is located on the rear exterior.
This caution label is located inside the unit.
SAFETY-RELATED COMPONENT WARNING !!
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
— 2 —
SERVICING NOTE
TABLE OF CONTENTS
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick­up block. Therefore, when checking the laser diode emission, ob­serve from more than 30 cm away from the objective lens.
MODEL IDENTIFICATION — AC POWER SUPPLY CODE —
AEP model
UK model
Mexican model (Without voltage selector) E, Argentine model (With voltage selector)
• Abbreviation AR : Argentine model MX : Mexican model
1. GENERAL
.......................................................................... 4
2. DISASSEMBLY
2-1. CD Door ...............................................................................5
2-2. Back Panel ............................................................................ 5
2-3. CD Mechanism Deck ............................................................ 6
2-4. Front Panel and Main Board ................................................. 6
2-5. CD Tray ................................................................................ 7
2-6. CD Decoder Board................................................................7
2-7. Base Unit ..............................................................................8
3. MECHANICAL ADJUSTMENTS ................................9
4. ELECTRICAL ADJUSTMENTS ................................. 9
5. DIAGRAMS
5-1. Circuit Boards Location ...................................................... 14
5-2. Block Diagrams
• Tuner Section (E, AR, MX models)................................. 15
• Tuner Section (AEP, UK models).................................... 17
• CD Section....................................................................... 19
• Deck Section .................................................................... 21
• Main Section (E, AR, MX models) ................................. 23
• Main Section (AEP, UK models)..................................... 25
• Power Section (E, AR, MX models)................................ 27
• Power Section (AEP, UK models) ................................... 28
5-3. IC Block Diagrams.............................................................. 29
5-4. Printed Wiring Board —Main Section —
(E, AR, MX models) ........................................................... 34
5-5. Schematic Diagram — Main Section —
(E, AR, MX models) ........................................................... 39
5-6. Schematic Diagram — Main Section —
(AEP, UK models) .............................................................. 43
5-7. Printed Wiring Board —Main Section —
(AEP, UK models) .............................................................. 47
5-8. Printed Wiring Board — CD Section —............................. 52
5-9. Schematic Diagram — CD Section — ............................... 57
5-10. Schematic Diagram — Panel Section — ......................... 61
5-11. Printed Wiring Board — Panel Section —....................... 65
5-12. Printed Wiring Board — Tuner Section —
(E, AR, MX models)......................................................... 71
5-13. Schematic Diagram — Tuner Section —
(E, AR, MX models)......................................................... 75
5-14. Schematic Diagram — Tuner Section —
(AEP, UK models) ............................................................ 79
5-15. Printed Wiring Board — Tuner Section —
(AEP, UK models) ............................................................ 83
5-16. IC Pin Function ................................................................ 87
6. EXPLODED VIEWS
6-1. Case and Back Panel ........................................................... 89
6-2. Front Panel Section ............................................................. 90
6-3. Cassette Mechanism Deck Section 1 .................................. 91
6-4. Cassette Mechanism Deck Section 2 .................................. 92
6-5. CD Mechanism Deck Section 1 .......................................... 93
6-6. CD Mechanism Deck Section 2 .......................................... 94
6-7. Base Unit Section (KSM-213BCM) ................................... 95
7. ELECTRICAL PARTS LIST ........................................ 96
— 3 —
Location of Parts and Controls
SECTION 1

GENERAL

!∞ !§ !¶
1
!™
!• !ª
2
@º @¡
34
@™
@∞
5
789
@•
6
1 Disc tray 2 DISC 1 button 3 DISC 2 button 4 DISC 3 button 5 § OPEN/CLOSE button 6 DISC SKIP button 7 VOLUME knob 8 CLOCK SET button 9 TIMER SET, CLOCK LIGHT buttonTIMER MODE buttonDisplay window !™ Remote sensorPOWER buttonPHONES jack !∞ p (stop) button
¢
P (play/pause) buttonSHUFFLE buttom !• PROGRAM buttonREPEAT buttonCD button TAPE button @™ PHONO buttonTUNER/BAND buttonPRESET – button @∞ PRESET + buttonMEMORY button– TUNING +/ 0/
) ± buttons
@• DBFB buttonPRESET EQ buttonDeck BTape operating buttons
r (recording) (for deck A only)
· (play) 0 (fast rewind) ) (fast forward) p6 (stop/eject) P (pause)
#™ Deck A
#™
— 4 —
SECTION 2

DISASSEMBLY

Note: Follow the disassembly procedure in the numerical order given.
2-1. CD DOOR
CD door
Two claws
Two claws
2-2. BACK PANEL
6
Back panel
5
Two screws (BVTP3x10)
3
Two screws (BVTP3x10)
1
Pull out the CD tray and remove the CD door with releasing claws into the direction of arrow.
1
Two screws (BVTP3x10)
2
Three screws (BVTP3x10)
— 5 —
4
Five screws (BVTP3x6)
2-3. CD MECHANISM DECK
1
Two screws (BVTP3x10)
4
Flat type wire (CN09)
5
CD mechanism deck
2
Two screws (BVTP3x10)
3
Harness (CN08)
2-4. FRONT PANEL AND MAIN BOARD
The TC mechanism deck section can be removed with six screws.
6
Connector (CN202)
5
Connector (CN203)
4
Two screws (BVTP3x10)
Front panel
8
Harness (CN205)
7
Connector (CN201)
9
3
Screw (BVTP3x10)
2
Rivet
Connector (CN701)
!™
Main board
1
Tuner board
0
Three screws (BVTP3X10)
— 6 —
2-5. CD TRAY
2
1
Screw (BVTP3x10)
Bracket
5
CD tray
3
Screw (BVTP3x10)
4
Bracket
2-6. CD DECODER BOARD
7
CD decoder board
2
Two screws (BVTP3x10)
4
Flat type wire (CN06)
5
Connector (CN05)
6
Flat type wire (CN01)
3
Two claws
— 7 —
1
Two screws (P2.6x4)
2-7. BASE UNIT
2
1
UD-cam
Screw (PTPWH2.6x8)
Note: When installing, set to
the groove of UD-cam.
4
Base unit
3
Two screws (PTPWH3X8)
— 8 —
SECTION 3

MECHANICAL ADJUSTMENTS

SECTION 4

ELECTRICAL ADJUSTMENTS

Precaution
1. Clean the following parts with a denatured alcohol-moistened swab:
record/playback heads pinch rollers erase head rubber belts capstan idlers
2. Demagnetize the record/playback head with a head demagne­tizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the parts adjusted.
5. The adjustments should be performed with the rated power sup­ply voltage unless otherwise noted.
Torque Measurement
Torque
FWD
FWD back tension
FF/REW
Torque meter Meter reading
CQ-102C
CQ-102C
CQ-201B
40 to 70 g • cm
(0.56 - 0.97 oz • inch)
1 to 5 g • cm
(0.01 - 0.07 oz • inch)
55 to 140 g • cm
(0.76 - 1.94 oz • inch)
DECK SECTION 0 dB=0.775V
1. Demagnetize the record/playback head with a head damagnetizer .
2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the parts adjusted.
4. The adjustments should be performed with the rated power sup­ply voltage unless otherwise noted.
5. The adjustments should be performed in the order given in this service manual. (As a general rule, playback circuit adjustment should be completed before performing recording circuit adjustment.)
6. The adjustments should be performed for both L-CH and R­CH.
Tape
P-4-A100
WS-48B
Record/Playback Head Azimuth Adjustment (Deck A, Deck B)
Note: Perform this adjustments for both decks.
Procedure:
1. Mode : Playback
test tape P-4-A100 (10kHz, –10dB)
Signal
10 kHz, –10 dB
3 kHz, 0 dB
SPEAKER terminal
Used for
Azimuth Adjustment
Tape Speed Adjustment
level meter
set
+ –
— 9 —
2. Turn the adjustment screw and check output peaks. If the peaks do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 2 dB of peak.
L-CH peak
screw position
R-CH peak
output level
within 2dB
L-CH peak
R-CH peak
within 2dB
screw position
3. Mode: Playback
Tape Speed Adjustment (Deck A)
Procedure:
1. Mode: Playback
test tape WS-48B (3kHz, 0dB)
set
SPEAKER terminal
frequency counter
+ –
2. Adjust the SFR201 so that the frequency counter reads 3,000 Hz ± 90 Hz.
Adjustment Location
[MAIN BOARD] — Component side —
test tape P-4-A100 (10kHz, –10dB)
in phase
SPEAKER terminal (L-CH)
L
set
R
SPEAKER terminal (R-CH)
Waveform of oscilloscope
45˚
good
90˚
oscilloscope
135˚ 180˚
wrong
4. After the adjustments, apply suitable locking compound to the parts adjusted.
Adjustment Location:
CN205
CN301
SFR201
Tape Speed
Sample Value of Wow and flutter
W. RMS (JIS) within 0.3% (test tape: WS-48B)
Adjustment screws REC/PB head (deck A) or PB head (deck B)
— 10 —
TUNER SECTION 0 dB=1µV
Note:As a FM front end (U1) is difficult to repair if faulty, replace
it with new one. (AEP, UK models)
AM T uning Volta ge Adjustment
DC voltmeter
Tuner board TP2
(VT)
Procedure:
1. Set the reception frequency of the unit to 530 kHz (10 kHz step) or 531 kHz (9 kHz step).
2. Adjust L105 for 1.2 ± 0.05 V reading on the DC voltmeter.
3. Set the reception frequency of the unit to 1,710 kHz (10 kHz step) or 1602 kHz (9 kHz step).
4. Confirm that the voltage reading on the DC voltmeter is within
8.0 ± 0.5 V.
Adjustment Location: TUNER board
AM T racking Adjustment
+ –
loop antenna
loop antenna (Supplied accessories)
AM RF SSG
30% amplitude modulation by 400Hz signal
60cm
Field strength dB (µV/m) = SSG output level dB (µV/m) –26dB.
Procedure:
1. Tune the set to 600 kHz (10 kHz step) or 603 kHz (9 kHz step).
2. Set the output of AM RF SSG so that the input level of the set will become 60 dB (µV/m).
3. Adjust L104 so that when the waveform on the oscilloscope is maximum, no noise appears.
4. Tune the set to 1,400 kHz (10 kHz step) or 1404 kHz (9 kHz step).
FM T uning Voltage Adjustment (EXCEPT AEP, UK models)
DC voltmeter
Tuner board TP2
(VT)
+ –
set
AM antenna terminal (JK101)
5. Adjust TC102 so that when the waveform on the oscilloscope is maximum, no noise appears.
• Repeat the procedures in each adjustment several times, and the
tracking adjustment should be finally done by the trimmer capacitors.
Adjustment Location: TUNER board
Procedure :
1. Set the reception frequency of the unit to 87.5 MHz.
2. Adjust L103 for 1.2 ± 0.05V reading on the DC voltmeter.
3. Set the reception frequency of the unit to 108 MHz.
4. Confirm that the voltage reading on the DC voltmeter is within
7.8 ± 0.5V.
Adjustment Location: TUNER board
— 11 —
FM T racking Adjustment (EXCEPT AEP, UK models)
FM RF SSG
oscilloscope
FM Tuned Level Adjustment
FM RF SSG
75
coaxial
set
open)
SPEAKER terminal
FM ANTENNA terminal (JK101)
Carrier frequency : 90 MHz, 106 MHz Modulation : AUDIO 1kHz, 75kHz deviation (100%) Output level : 20 dB (at 75
+ –
Procedure:
1. Tune the set to 90 MHz.
2. Adjust L102 so that when the waveform on the oscilloscope is maximum, no noise appears.
3. Tune the set to 106 MHz.
4. Adjust TC101 so that when the waveform on the oscilloscope is maximum, no noise appears.
• Repeat the procedures in each adjustment several times, and the
tracking adjustment should be finally done by the trimmer capacitors.
Adjustment Location: TUNER board
Adjustment Location
set
Carrier frequency : 98 MHz Modulation : AUDIO 1 kHz, 75 kHz
Output level : 28 dB (at 75
deviation (100%)
open)
FM ANTENNA terminal (JK101)
Procedure:
1. Supply a 28 dB 98 MHz signal from the ANTENNA terminal.
2. Tune the set to 98 MHz.
3. Adjust SFR101 to the point (moment) when the TUNED indica­tor will change from going off to going on.
Adjustment Location: TUNER board
EXCEPT AEP, UK models [TUNER BOARD] — Component side —
FM T uning V oltage
JK101
TP2 (VT)
L104
TC102
L103
TC101
L102
L105
AM T racking
FM T racking
AM T uning Voltage
FM T uned Level
SFR101
CN101
AEP, UK models [TUNER BOARD] — Component side —
FM T uned Level
JK101
L104
U1
TP2 (VT)
AM T rac king
TC102
L105
AM T uning Voltage
SFR101
T101
— 12 —
CD SECTION
Note:
1. CD Block is basically constructed to operate without adjustment. Therefore, check each item in order given.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.
3. Use an oscilloscope with more than 10M impedance.
4. Clean the object lens by an applicator with neutral detergent when the signal level is low than specified value with the fol­lowing checks.
5. Adjust the focus bias adjustment when optical block is replaced.
Focus Bias Adjustment
CD DECODER board
CN12
FEO
VC
Procedure:
1. Connect DC voltmeter to test point CN12 (FEO), (VC) on CD DECODER board.
2. Turned Power switch on.
3. Put disc (YEDS-18) in and stop.
4. Adjust VR01 so that the DC voitmeter reading is 0 ± 20 mV.
Adjustment Location: CD DECODER board
DC voltmeter
+
RF Level Check
CD DECODER board
TP (RF) CN12 (VC)
Procedure :
1. Connect oscilloscope to test point TP (RF) on CD DECODER board.
2. Turned Power switch on.
3. Put disc (YEDS-18) in and playback.
4. Confirm that oscilloscope waveform is clear and check RF sig­nal level is correct or not.
Note: Clear RF signal waveform means that the shape “” can be
clearly distinguished at the center of the waveform.
oscilloscope
VOLT/DIV: 200 mV TIME/DIV: 500 nS
+0.3
level: 1.0 Vp-p
–0.2
Adjustment Location: CD DECODER board
5-1. CIRCUIT BOARDS LOCATION
DISC LED board
PANEL board
SENSOR board
R/P SWITCH board
MAIN Board
SECTION 5 DIAGRAMS
O/C board
TUNER board
AC SUPPLY board (E, Argentine, Mexican) AC POWER SUPPLY board (AEP, UK)
VOL SELECT board (E, Argentine)
Focus Gain Adjustment (VR02)
This gain has a margin, so even if it is slightly off. There is no problem. Therfore, do not perform this adjusment. Please note that it should be fixed to mechanical center position when you moved and do not know original position.
Adjustment Location
[CD DECODER BOARD] — Component side —
CN12
IC03
Focus Bias
Focus Gain
VR01
VR02
VC
FEO
IC01
R07
RF Level
— 13 —
SW (C) board
CD DECODER board
SW (D) board
SW (B) board
MOTOR board
SW (A) board
MOTOR (6P) (S) board
— 14 —
HCD-G1
5-2. BLOCK DIAGRAMS — TUNER SECTION — (E, AR, MX models)
JK101
ANTENNA
FM
75 OHM
AM
TP2
AM TUNING
VOLTAGE
FM TUNING
VOLTAGE
09
L101
D106
TC101,L102
FM TRACKING
TP2VT
G
L104
L104,TC102
AM TRACKING
• R CH is omitted
• Signal path : FM : AM
• Abbreviation AR : Argentine model. MX : Mexican model.
RF IN IF OUT
1 6
FM FRONT
END
IC101
MAX IN OSC
3 8
D107
TC102
Q107,108
T101
L103
FM TUNING
L.P.F
X201
7.2MHz
21 1 24
X IN
PD 1
L103
VOLTAGE
FM OSC
AMP Q102
AM RF
AMP Q106
B+
X OUT
CF101
10.7MHz
Q105
17
FM B+
L OUT
14
ST IND
DI CLK CE
MUTE
STEREO
DO
TU L
A
MAIN
SECTION
(Page 23)
FM/AM MPX
IC102
CF102
FM IF
10.7MHz
AMP Q101
AM TUNING
VOLTAGE
L105
B+
19
FM IN
PLL
IC201
SFR101
FM TUNED LEVEL
1 FM IF
23
OSC
22
AFC
21
AM RF
24
OSC/FMSD
AM/FM
TU LED
6 10
AGC
CONT.
Q109
7 15
18
AM IN
SD/IN
16
L CTR
H CTR
FM DET
MPX VCO
MPX IN AM/FM
ST IND
AM MIX
PH DET
SMET
201112 13
12 13
SD
AM/FM
PH DET
14
8
17
16 18
7
2
PL DET
ST/MONO
CF104
10.4MHz
CF105
19kHz
T102
AM IF
4
IF
TP1
G
CF103
450kHz
5
DO
3 4
2
DI
CE
CLK
— 15 —
— 16 —
— TUNER SECTION — (AEP, UK models)
JK101
ANTENNA
FM
75 OHM
AM
L101
TP2
AM TUNING
VOLTAGE
L104
• R CH is omitted
• Signal path : FM : AM
RF IN IF OUT
1 7
FM FRONT
VT OSC
5 8
TP2
TC102
L104,TC102
AM TRACKING
U1
END
L.P.F
Q107,108
21 1 24
PD 1
X201
7.2MHz
X IN
AM RF
B+
X OUT
AMP Q106
CF101
10.7MHz
Q105
17
FM B+
HCD-G1
L OUT
14
FM/AM MPX
IC102
CF104
PH DET
14
8
17
16
18
7
2
PL DET
ST/MONO
10.7MHz
CF105 19kHz
T101
FTZ. FILTER
3 6
1
T102
5
DO
CF102
FM IF
10.7MHz
AMP Q101
AM TUNING
VOLTAGE
L105
B+
19
FM IN
PLL
IC201
SFR101
FM TUNED LEVEL
1 FM IF
23
OSC
22
AFC
21
AM RF
24
OSC/FMSD
AM/FM
TU LED
6 10
7 15
18
AM IN
SD/IN
16
L CTR
H CTR
FM DET
MPX VCO
MPX IN
AM/FM
ST IND
AM MIX
PH DET
SMET
201112 13
12 13
SD
AM/FM
TP1
AM IF
IF
CF103
450kHz
R OUT
4
G
3 4
2
DI
CE
CLK
TU L
15
R CH
ST IND
A
DI
MAIN
CLK
SECTION
CE
(Page 25)
MUTE
STEREO
DO
09
— 17 — — 18 —
HCD-G1
— CD SECTION —
OPTICAL PICK-UP BLOCK
DETECTOR
A
C
B
D
E
F
7
B+
LASER DIODE
PD
TRACKING
2-AXIS
DEVICE
• R CH is omitted
• Signal path : CD
COIL
FOCUS
COIL
DIGITAL SIGNAL PROCESSOR, D/A CONVERTER, DIGITAL FILTER
RF
4
1
2
5
6
10
LD
FOCUS
TRACKING
RF LEVEL
MOTOR
SPINDLE
MOTOR
M102 SLED
M101
APC Q01
LD ON
Q02
CN12
M
M
2
1
09
VC
FOCUS
TRACKING
VR01
3536PD1
PD2
E
39
F
38
LD
33
PD
34
48
VC
••
45
ATSC
FEO
1
FEBIAS
37
VO3(+)
18
VO3(-)
17
VO4(+)
15
VO4(-)
16
VO2(+)
12
VO2(-)
11
VO1(+)
13
VO1(-)
14
FOCUS/TRACKING
SERVO, RF AMP
IC01 (1/2)
TRACKING
COIL
DRIVE
FOCUS
COIL DRIVE
FOCUS/TRACKING
COIL DRIVE, SPINDLE/SLED MOTOR DRIVE
IC03
SLED MOTOR
DRIVE
SPINDLE
MOTOR
DRIVE
DATA
SENS
C. OUT
XRST
FE M
TA M
CLK
FOK
FE O
TA O
XLT
VIN3
VIN4
VIN2
VIN1
31RF 0
CN2
42TEO
VC
16 15
24
VR02
SLED SERVO
IC01 (2/2)
SL O SL M
OP
OUT
FOCUS
GAIN
SL P
14
23IN -
9MUTE
EI
40
19 20 21
24 23 25
22
6 7 13
12
25
27
6
4
DIGITAL
36
PLL
DEMODULATOR
SUB CODE
PROCESSOR
CLKO
17
XLTO
16
DATO
15
SERVO
AUTO
SEQUENCER
SEIN
13
CNIN
14
FOK
23
XLON
22
8
XRST
MDP
25
M103 TURN
TABLE
MOTOR
M104 TRAY
MOTOR
CPU
INTERFACE
M
M
EFM
IC04
INTERFACE
DIGITAL
CLV
TURN TABLE
MOTOR DRIVE
Q10,11,14,15
TURN TABLE
MOTOR DRIVE
CONTROL
Q13
TRAY MOTOR
DRIVER
Q06 - Q09
D/A
S05
LIMIT
SWITCH
CLOCK
GENERATOR
SPOA
18
6 7
11
8 9
4
XTA0
74 73
33.8688MHz
T.T+ T.T-
DOWN
TRAY + TRAY -
XRST
DIGITAL
FILTER
1BIT DAC
XLT01
+
XTA1
MUTE
6
2
B.BOOST
MUTE
CONTROL
TRAY/TABLE
MOTOR DRIVER,
REG CONTROL
IC02
NLPWM
LPWM
DATA SQCK CLOK SQSO SCOR SENS
XLAT
DATA I
CLOK
MIX AMP
70 69
9 5
11
4 1 7
IC05
+
-
CD L
DATA SQCK
SQSO SCOR SENS
C
CONTROL
MUTE
MAIN
SECTION
(Page 23,25)
E
POWER
SECTION
(Page 27,28)
10
5 13 14 15
STB
3
10
UP
S01
OPTICAL PICK-UP
UP DOWN
UP/DOWN DET
XLAT
COUNT FOK
DI CLK STB
B. BOOST
UP DOWN
— 19 —
— 20 —
— DECK SECTION —
TAPE B
HP901
PB HEAD
TAPE A
HRP901
REC/PB
HEAD
HE901
ERASE
HEAD
R CH
PLAY/REC CONTROL Q203,205
PLAY/REC CONTROL
DRIVE
Q207
R CH
D208
R CH
R CH
BIAS OSC COIL
PLAY/REC CONTROL
Q201
L201
D209
HCD-G1
NF
3
CH1/A
1
CH1/B
2
A/B
Q211
BIAS OSC
Q218
­+
REC/PLAY
EQ AMP
IC201
9
REC SWITCH
DRIVE
Q217
GROUND
SWITCH
Q220
PB L
REC L
B
MAIN
SECTION
(Page 23,25)
5
PRE OUT
TAPE A/TAPE B
19
REC
+
OUT
-
REC IN
11
NF
10
D205
MUTE
Q209
MUTE
SWITCH
Q216
Q219
D202
+
TAPE A SWITCH
Q214
D212
D211
D203
D213
SW201
REC/PLAY
SWITCH
PLAY
REC
TAPE A/B
SWITCH
Q213
D201
• R CH is omitted
• Signal path : PB (DECK A) : PB (DECK B) : REC (DECK A)
B +
D207D206
SFR201
TAPE SPEED
S201
A DECK
S202
B DECK
S203 PLAY
M
M901
REEL/CAPSTAN
MOTOR
B +
09
CD SYNC
— 21 — — 22 —
HCD-G1
,
— MAIN SECTION — (E, AR, MX models)
A
TUNER
SECTION
(Page 16)
B
DECK
SECTION
(Page 22)
C
CD
SECTION
(Page 20)
09
TU L
STEREO
MUTE
ST IND
REC L
PB L
CD SYNC
CD L
B. BOOST
SQSO SCOR SENS
XLAT
COUNT
DOWN
SQCK
DATA
AM TUNING
JK301
PHONO 5 7
DI
CLK
CE
DO
Q491
TAPE SELECTOR
DI
CLK
FOK STB
UP
MODE
SWITCH
Q606
STEP
SWITCH
SW751
AR
E
DI1
11
9 12 10
19
FM ST IN
TU MUTE OUT
KI 0
29 - 32 • 34
MATRIX
INPUT SELECTOR
L2
L4 L1
L3
TUNED
SWITCH
Q751
16
TUNED
KEY
KI 4
IC401
CONTROL
CLDICE
1514
DI
CLK
69 - 80 • 1 - 12
LT
OUT
16
CE
S00
LCD DISPLAY
64 65 66
LCD601
LINE AMP
3
DI
DO
S23
CLK
CLK
21 - 24
CE
COM 0
Q451
2
IN
LVR
ELECTRICAL
VOLUME
DRIVER
CE
COM 3
1
LVR OUT
LED601
DBFB
LED
Q605
BASS
BOOST
Q461
BASS
BOOST
SWITCH
Q463
DI
1
CLK
2 3
17
LATCH OUT
SYSTEM CONTROLLER, LCD DRIVER
X1
X2
59 58
X601
4.19MHz
PHONO AMP
IC301
TUNER MUTE
Q1
IC402
1
2
13
36 63 61
18
41 SQSO 43
SCOR
44
SENS XLAT
60 38
COUNT
37
FOK
67
STB
62
DI2
45
GFS
39
SQCK/MODE SW IN
40
DATA
5G2
SYS.REC IN
KO A
13 - 15
1 - 3
A - C
SELECTOR
IC602
TAPE REC OUT
KO C
15
Y0
10
Y5
• 7
Y7
5 7
LED DRIVER
IC603
DISC1
DATA CLK
DISC3
LATCH
RST
IC601
CONTROL RECEIVER
42
REMOTE
RM601
L.P.F
IC403
17 12
6
REM. IN
2
D617
MUTE
Q581
MUTE
SWITCH
Q583,584
B+
D582, 583
POWER AMP
IC501
13 12
7 8
STANDBY CONTROL
Q501 - Q503
MUTE
Q604
LED602 - LED603
DISC 1 - 3
D584
OVERLOAD
Q551
PROTECT
SWITCH
Q553
VCC
ON
MUTE
PROTECTOR
IC502
STBY
SWITCH
Q586
MUTE
SWITCH
Q603
49 48
S02
OPEN/CLOSE
DET
DET
4
DET
OUT
67
AC OFF
4
DET
STBY
SWITCH
Q585
SYSTEM MUTE OUT
TRAY OPEN SW
TRAY CLOSE SW
S03
TURN TABLE
POSITION DET
RL501
1
6
MUTE
Q587
MUTE
SWITCH
Q589
POWER ON
DET
Q782
POWER ON
POWER OUT
DISC COUNT SW
46 47
TURN TABLE
OPERATION DET
3
R-CH
D585,
781
B+
DET
Q601
POWER DOWN IN
TURN TABLE SW
S04
POWER ON
B+
RESET
SWITCH
Q602
68555352
DET
Q781
RESET
JK501
SPEAKER
JK502
PHONES
P. ON
PWN
(Page 27)
D
POWER
SECTION
• R CH is omitted.
• Signal path : FM : PB : REC : CD : PHONO
• Abbreviation AR : Argentine model. MX : Mexican model.
— 23 —
— 24 —
Loading...
+ 42 hidden pages