Sony DF-200 Service manual
D-F200/F201
SERVICE MANUAL
Ver 1.0 2002. 05
SPECIFICATIONS
US Model
D-F200
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Chinese Model
D-F201
Model Name Using Similar Mechanism D-EQ550
CD Mechanism Type CDM-3125ER
Optical Pick-up Name DAX-25E
CD player
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wavelength: λ = 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW (This output
is the value measured at a distance of 200 mm
from the objective lens surface on the optical
pick-up block with 7 mm aperture.)
D-A conversion
1-bit quartz time-axis control
Frequency response
20 – 20,000 Hz +1/–3 dB
(measured by JEITA CP-307)
Output (at 4.5 V input level)
Headphones (stereo minijack)
• D-F200:
Approx. 5 mW + Approx. 5 mW
at 16 ohms
• D-F201:
Approx. 5 mW + Approx. 5 mW
at 16 ohms (Except FR model)
Approx. 0.2 mW + Approx. 0.2 mW
at 16 ohms (FR model)
Radio
Frequency range
• D-F200, F201 (CND, E13, E92, AUS,
MX, AR): (STEP switch)
9 kHz step:
FM: 87.5 – 108.0 MHz
AM: 531 – 1,710 kHz
10 kHz step:
FM: 87.5 – 108.0 MHz
AM: 530 – 1,710 kHz
• D-F201 (AEP, UK, FR, CET, CH):
FM: 87.5 – 108.0 MHz
AM: 531 – 1,602 kHz
Antenna
FM: Headphones/earphones cord antenna
AM: Built-in ferrite bar antenna
General
Power requirements
For the area code of the model you purchased,
check the upper left side of the bar code on the
package.
•Two LR6 (size AA) batteries: 3 V DC
•AC power adaptor (DC IN 4.5 V jack):
US/CND/E92/MX model: 120 V, 60 Hz
AEP/E13/FR/CET model: 220 – 230 V,
50/60 Hz
UK model: 230 – 240 V, 50 Hz
AUS model: 240 V, 50 Hz
CH/AR model: 220 V, 50 Hz
Battery life* (approx. hours)
(When you use the CD player on a flat and stable
surface.)
Playing time varies depending on how the CD player
is used.
When using ESP RADIO
on off on
Two sony alkaline 31 33 70
batteries LR6(SG)
(produced in Japan)
* Measured value by the standard of JEITA
(Japan Electronics and Information Technology
Industries Association).
** Charging time varies depending on how the
rechargeable battery is used.
FM/AM PORTABLE CD PLAYER
Operating temperature
5°C – 35°C (41°F – 95°F)
Dimensions (w/h/d) (excluding projecting
parts and controls)
Approx. 161 × 26.3 × 130.3 mm
(6
3/8 × 1 1/16 × 5 1/4 in.)
Mass (excluding accessories)
Approx. 210 g (7.5 oz.)
Supplied accessories
For the area code of the location in which you
purchased the CD player, check the upper left
side of the bar code on the package.
Headphones/earphones (1)
AC power adaptor (1) (D-F201)
Design and specifications are subject to change
without notice.
•Abbreviation
CND : Canadian model
E13 : AC 220 – 230V area in E model
E92 : AC 120V area in E model
AUS: Australian model
CH : Chinese model
FR : French model
CET : East European & CIS model
MX : Mexican model
AR : Argentina model
9-874-005-01
2002E0400-1
© 2002.05
Sony Corporation
Personal Audio Company
Published by Sony Engineering Corporation
1
D-F200/F201
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270°C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
TABLE OF CONTENTS
1. SERVICE NOTE................................................................. 3
2. GENERAL
Getting started ......................................................................... 4
3. DISASSEMBL Y
3-1. Cabinet (Upper) Assy.......................................................... 5
3-2. Upper Lid Assy ................................................................... 5
3-3. Main Board, MD Assy ........................................................ 6
3-4. Optical Pick-up, Motor ....................................................... 6
4. ELECTRICAL ADJUSTMENTS
Tuner Section........................................................................... 7
CD Section .............................................................................. 8
5. DIAGRAMS
5-1. IC Pin Descriptions ............................................................. 9
5-2. Block Diagram –CD Section–........................................... 15
5-3. Block Diagram –Tuner Section–....................................... 16
5-4. Block Diagram –Power Supply Section–.......................... 17
5-5. Printed Wiring Board –Main Section– .............................. 18
5-6. Schematic Diagram –Main Section (1/3)– ......................... 20
5-7. Schematic Diagram –Main Section (2/3)– ......................... 21
5-8. Schematic Diagram –Main Section (3/3)– ......................... 22
5-9. IC Block Diagrams............................................................ 23
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY P ARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
6. EXPLODED VIEWS
6-1. Cabinet (Upper) Section.................................................... 25
6-2. Cabinet (Lower) Section ................................................... 26
6-3. CD Mechanism Deck Section (CDM-3125ER) ................27
7. ELECTRICAL PARTS LIST ........................................ 28
ATTENTION AU COMPOSANT AYANT RAPPORT
LES COMPOSANTS IDENTIFIÉS P AR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES
SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.
NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES
SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL
OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
À LA SÉCURITÉ!!
2
TP416
Q53
C43
R72
R70
L312
CT3
C9
C8
C39
C204
C104
C318
C361
C353
R8
C352
C201
R353
TAP802
C360
R25
R101
R316
R201
D301
TAP802
– MAIN BOARD (SIDE A) –
SECTION 1
SERVICE NOTE
D-F200/F201
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body .
During repair, pay attention to electrostatic breakdown and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
Precautions for Checking Emission of Laser Diode
Laser light of the equipment is focused by the object lens in the
optical pick-up so that the light focuses on the reflection surface
of the disc. Therefore, be sure to keep your eyes more then 30 cm
apart from the object lens when you check the emission of laser
diode.
Before Replacing the Optical Pick-Up Block
Please be sure to check throughly the parameters as par the “Optical Pick-Up Block Checking Procedures” (Part No.: 9-960-027-
11) issued separately before replacing the optical pick-up block.
Note and specifications required to check are given below.
• FOK output : IC601 yg pin
When checking FOK, remove the lead wire to disc motor.
• RF signal P-to-P value : 0.45 ± 0.1 Vp-p
• The repairing grating holder is impossible.
Laser Diode Checking Methods
During normal operation of the equipment, emission of the laser
diode is prohibited unless the upper lid is closed while turning ON
the S801. (push switch type)
The following two checking methods for the laser diode are
operable.
• Method:
Emission of the laser diode is visually checked.
1. Open the upper lid.
2. W ith a disc not set, turn on the S801 with a scre wdri ver having a
thin tip as shown in Fig.1.
or TAP802 is shorted as shown in Fig.2.
Note: Do not push the detection lever strongly , or it may be bent
or damaged.
3. Press the N X button.
4. Observing the objective lens, check that the laser diode emits
light.
When the laser diode does not emit light, automatic power
control circuit or optical pick-up is faulty.
In this operation, the objective lens will move up and down 5
times along with inward motion for the focus search.
S801
– MAIN BOARD (SIDE B) –
TP18
TP5
C2
D1
R2
C34
C37
R6
D2
L4
C36
C41
R24
C15
R9
C3
TP20
L1
L3
AM
FERRITE-
ROD
ANTENNA
16
C13
C10
CF1
R3
C46
75
TP816
R841
S810
TP1
S801
CD DOOR
OPEN
C841
D3
S801
Fig. 1
detection lever
detection lever
D304
R19
R18
R16
C301
FR
MODEL
C319
C354
C7
R7
main board
TP311
Q7
C29
Q8
R17
R843
R26
R354
R102
132412
R202
C351
R317
C359
TP813
R27
R28
C30
IC302
FB311
C313
1
S811
FB111
C300
R154
C350
R254
C254
C154
Fig. 2
3
D-F200/F201
Locating the controls
For details, see pages in parentheses.
CD player (front)
SECTION 2
GENERAL
This section is extracted
from instruction manual.
1 i (headphones)
jack
2 OPEN button
3 SOUND/
PRESET –
button
4 VOLUME
control
5 MENU/PRESET
button
6 RADIO ON•BAND/
MEMORY button
+
8 u (play/pause)
button
9 x (stop)• RADIO OFF
button
q; Strap holes
qa DC IN 4.5 V
(external power
input) jack
qs ./>
(AMS/search) •
TUNE –/+ buttons
7 Display
CD player (inside)
ESP switch
qf
A
VLS switch
qg
qd HOLD switch
CD player (rear)
qh
LOCAL/DX switch : US, CND, E92, MX, AR model
MONO/ST (stereo) switch : AEP, UK, E13, AUS,
CH, FR, CET model
qj STEP switch :
US, CND, E13, E92,
AUS, MX, AR model
qk Battery compartment
4
SECTION 3
y
DISASSEMBLY
• The equipment can be removed using the following procedure.
D-F200/F201
SET
3-1. CABINET (UPPER) ASSY
(Page 5)
3-3. MAIN BOARD, MD ASSY
(Page 6)
Note : Follow the disassembly procedure in the numerical order given.
3-1. CABINET (UPPER) ASSY
1
B 2x10
8
6
claws
9
3-2. UPPER LID ASSY
(Page 5)
3-4. OPTICAL PICK-UP, MOTOR
(Page 6)
0
cabinet (upper) sub ass
4
claws
7
3-2. UPPER LID ASSY
claws
3
B 2x10
battery case lid
2
2
upper lid assy
1
boss
5
claws
claws
cabinet (upper) sub assy
5
D-F200/F201
t
3-3. MAIN BOARD, MD ASSY
Note: When installing, fit the knob (HOLD) and S803.
1
CN501
7
MAIN board
cabinet (lower) sub assy
3
CN503
2
CN502
4
MD assy
S803
5
S812
6
S813
battery terminal (–)
battery terminal (+.–)
3-4. OPTICAL PICK-UP, MOTOR
5
sled motor assy (M2)
6
gear (B)
4
gear cover
3
B 1.7x5
knob (HOLD)
1
B 1.7x5
2
turntable motor assy (M1)
chassis
7
qa
screw (feed) assy
8
retainer, shaf
P 1.4x3.5
qd
standard shaft
qs
optical pick-up block
0
rack
9
screw (M1.4)
6
)
SECTION 4
ELECTRICAL ADJUSTMENTS
D-F200/F201
TUNER SECTION 0 dB = 1 µV
• FM Section
Setting:
RADIO ON•BAND/MEMORY button : FM
STEP switch : 10k
FM RF signal
generator
0.01
µ
F
75 kHz frequency
deviation by 1 kHz signal
output level : as low as possible
• AM Section
Setting:
RADIO ON•BAND/MEMORY button : AM
STEP switch : 10k
AM RF signal
generator
Put the lead-wire
antenna close to
the set.
TP3 (RF-IN)
set
FM FREQUENCY COVERAGE
CHECK
Frequency Display 87.5 MHz 108 MHz
Reading on Digital voltmeter 3.0 ± 1.4 V 7.8
+ 4.0 V
– 2.5 V
Adjustment Part <confirmation> <confirmation>
FM TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter.
L2 CT1
87.5 MHz 108 MHz
AM IF ADJUSTMENT
Adjust for a maximum reading on level meter.
T1
450 kHz
AM FREQUENCY COVERAGE
CHECK (US, CND, E, AUS model)
Frequency Display 530 kHz 1,710 kHz
Reading on Digital voltmeter 0.9
– 0.5 V – 0.7 V
+ 0.7 V
5.0
+ 0.8 V
Adjustment Part <confirmation> <confirmation>
30% amplitude
modulation by
400 Hz signal
• Connecting Level Meter (FM and AM)
level meter
(range: 0.5–5 V ac
Ω
16
set
i
jack (J302)
• Connecting Digital Voltmeter (FM and AM)
digital
voltmeter
Ω
100 k
TP81 (VT)
AM FREQUENCY COVERAGE
CHECK (AEP, UK, CH model)
Frequency Display 531 kHz 1,602 kHz
Reading on Digital voltmeter 1.0 ± 0.5 V 4.4
+ 1.5 V
– 0.3 V
Adjustment Part <confirmation> <confirmation>
AM TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter.
L4 CT3
620 kHz (621 kHz) 1,400 kHz (1,404 kHz)
( ): AEP, UK, CH model
• Abbreviation
CND : Canadian model
AUS : Australian model
CH : Chinese model
Adjustment Location: See page 8.
•Repeat the procedures in each adjustment several times, and the
frequency coverage and tracking adjustments should be finally
done by the trimmer capacitors.
•For FM adjustment, fix the FM RF coil (L1) as shown ne xt page
and then perform tracking adjustment at L2 and CT1.
Lastly check the voltage value.
•For AM adjustment, fix the ferrite-rod antenna (L3) as shown
next page and then perform tracking adjustment at L4 and CT3.
Lastly check the voltage value.
7
D-F200/F201
Adjustment Location:
– MAIN BOARD (SIDE A) –
CN501
AM IF ADJ
TP3
RF-IN
L3
L1
T1
CT1
FM TRACKING ADJ
L2
CT3 L4
AM TRACKING
ADJ
CD SECTION
CD section adjustments are done automatically in this set.
In case of operation check, confirm that focus bias.
FOCUS BIAS CHECK
1. Connect the oscilloscope between TP603 (RF) and GND on
main board.
2. Insert the disc (YEDS-18). (Part No. : 3-702-101-01)
3. Press the N X button.
4. Confirm that the oscilloscope waveform is as shown in the
figure below. (eye pattern)
A good eye pattern means that the diamond shape ( ) in the
center of the waveform can be clearly distinguished.
• RF signal reference waveform (eye pattern)
VOLT/DIV : 20 mV (10 : 1 probe in use)
TIME/DIV : 500 nS
RF level :
±
0.1 Vp-p
0.45
TP81
VT
IC51
Test Point:
– MAIN BOARD (SIDE B) –
D602
R623
R622
R451
R452
TP630
US,CND,E92,
X M
AR,M
C624
D603
ODEL
FB601
R647
C618
R629
L604
C621
C310
R630
30
31
L603
X601
60
C617
61 90
R611
R652
C604
R651
R612
C605
C626
C606
R617
TP33
R615
R613
R653
R614
C601
C608
IC601
C602
C607
C627
R616
R602
R618
R601
TP604
C610
R619
TP603
1
120
91
TP605
C609
R654
R605
TP602
TP606
C613
R607
C641
C614
VDR601
R620
R609
C612
R606
TP601
C611
R604
R625
C630
TP412
TP410
C616
TP626
TP627
When observing the eye pattern, set the oscilloscope for AC range
and raise vertical sensitivity.
8
TP603
RF
SECTION 5
DIAGRAMS
5-1. IC PIN DESCRIPTIONS
• IC51 TC9327AF-631 (TUNER PLL, LCD DRIVER)
Pin No. Pin Name I/O Pin Description
1 to 4 COM1 to 4 O LCD driver signal output
5 to 20 S1 to 16 O LCD driver signal output
21 AM STEP-I I AM 9K/10K tuning step select signal input (initialization)
22 DEST2-I I Bit2 tuner destination setting signal input (Fixed at “L” in this set)
23 DEST1-I I Bit1 tuner destination setting signal input
24 DEST0-I I Bit0 tuner destination setting signal input
25 XLOCAL/XMONO-DET-I I LOCAL/DX or MONO/STEREO ON-OFF switch detect signal input
26, 27 NC — Not used. (Open)
28 LCDREQ-I I LCD display request signal input
29 LID OPEN I CD door open detect signal input
30 EEP D0/D1-IO I/O Data signal input/output for EEPROM IC.
31 EEP SK-O O Clock signal output for EEPROM IC.
32 EEP CS-O O Chip select signal output for EEPROM IC.
33 XL/O-I I Line out signal input
34, 35 NC — Not used. (Open)
36 MEM-KEY (3-BIT) I Memory key signal input (Fixed at “H” in this set)
37 PRESET KEY I Not used in this set. (Open)
38 CD ACK-I O CD acknowledge signal output
39 CDON-IWP-CDU I CD ON request signal input (Wake-up tuner in sleep mode)
40 I/O (RESERVED) — Not used. (Open)
41 NC — Not used. (Open)
42 AD1 KEY I Set keys signal input
43 AD2 RMKEY I Remote key signal input (Fixed at “L” in this set)
44 AD3 BATT HIDC I Battery/HiDC level detect signal input
45 AD DC REF I Reference DC signal input of A/D.
46 SDI-I-CDU I Serial data signal input from system control IC.
47 SDO-O-CDU (RESERVED) O Serial data signal output to system control IC.
48 SCK-I-CDU I Serial clock signal input from system control IC.
49 TUBEEP-O O Beep sound control signal output
50 NC (I/O) — Not used. (Open)
51 XHOLD-I-SW I HOLD detect signal input
52 XAVLS-I-SW I AVLS detect signal input
53 XDC IN DET-I I DC-in detect signal input
54 TU ON-O O Tuner ON request signal output
55 ST OR DX-O-CTR O LOCAL/DX or MONO/STEREO ON-OFF control signal output
56 TUBASS2-O O MEGA BASS 2 sound mode signal output (Not used in this set)
57 TU TEST MODE I Tuner test mode detect signal input
58 TUBASS1-O O MEGA BASS 1 sound mode signal output (Not used in this set)
59 AM/XFM-O O Band control FM/AM signal output to tuner IC.
60 +B ON/OFF O Radio power ON/OFF signal output
61 IFREQ-O O IF request signal output
62 TUMUTE-O O Mute HP control signal output
63 TEST — Not used. (Open)
64 IFIN I FM/AM IF signal input
65 EO (DO1) O PLL error signal output
66 NC (DO2) — Not used. (Open)
67 HOLD I Not used. (Connect to ground in this set)
68 NC — Not used. (Open)
69 GND — Ground
70 FM IN I FM oscillation signal input
D-F200/F201
9
D-F200/F201
Pin No. Pin Name I/O Pin Description
71 AM IN I AM oscillation signal input
72 VDD (1.8-2.2V) — Power supply pin
73 RESET I Power reset signal input
74 XOUT O Crystal oscillation signal output (75 kHz)
75 XIN I Crystal oscillation signal input (75 kHz)
76 VXT — Crystal oscillation signal pin
77 VLCD — LCD voltage doubler
78, 79 C1, 2 — LCD voltage doubler
80 VEE — Constant voltage output to LCD.
• IC601 CXD3029R (RF AMP, DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR, D-RAM CONTROLLER)
Pin No. Pin Name I/O Pin Description
1 XRAS O Row address strobe signal output to the D-RAM (IC602)
2 XWE O Data input enable signal output to the D-RAM (IC602)
3 to 6 D1, D0, D3, D2 I/O Two-way data bus with the D-RAM (IC602)
7, 8 TEST1, TEST2 O Output terminal for the test Not used (open)
9 XCAS O Column address strobe signal output to the D-RAM (IC602)
10 WFCK O WFCK signal output terminal
11 to 13 A9 to A7 O Address signal output to the D-RAM (IC602)
14 DVSS — Ground terminal (for D-RAM interface)
15 to 17 A6 to A4 O Address signal output to the D-RAM (IC602)
18 XRDE I D-RAM read enable signal input terminal Not used (open)
19 VDD0 — Power supply terminal (digital system)
20 CLOK I Serial data transfer clock signal input from the system controller (IC801)
21 SDTO I Serial data input from the system controller (IC801)
22 SENS O Serial data output to the system controller (IC801)
23 XLAT I Serial data latch pulse signal input from the system controller (IC801)
24 XSOE I Serial data output enable signal input from the system controller (IC801)
25 SYSM I
26 WDCK O GRSCOR signal output to the system controller (IC801)
27 SCOR O Subcode sync (S0+S1) detection signal output to the system controller (IC801)
28 XRST I Reset signal input from the system controller (IC801) “L”: reset
29 PWMI I Spindle motor external control signal input terminal (fixed at “L”)
30 XQOK I Subcode Q OK signal input terminal Not used (open)
31 XWRE I D-RAM write enable signal input terminal Not used (open)
32 R4M O System clock output to the system controller (IC801)
33 VSS0 — Ground terminal (digital system)
34 SQCK I SQSO readout clock signal input terminal Not used (fixed at “H”)
35 SCLK I SENS serial data read clock signal input terminal Not used (fixed at “H”)
36 SQSO O CD text data output terminal Not used (open)
37 XEMP O D-RAM read prohibition signal output terminal Not used (open)
38 XWIH O D-RAM write prohibition signal output terminal Not used (open)
39 SBSO O Subcode P to W serial data output terminal Not used (open)
40 EXCK O SQSO readout clock signal output terminal Not used (pull down)
41 XSTL I
42 HVSS — Ground terminal (for headphone)
43 HPL O
Analog muting on/off control signal input from the system controller (IC801)
“H”: muting on
Input terminal for the system clock frequency setting
“L”: 16.9344 MHz, “H”: 33.8688 MHz (fixed at “L” in this set)
PDM signal output for L-ch headphone to the headphone amplifier (IC302)
Not used (open)
10
D-F200/F201
Pin No. Pin Name I/O Pin Description
44 HPR O
45 HVDD — Power supply terminal (for headphone)
46 XVDD — Power supply terminal (for master clock)
47 XTAI I System clock input terminal (16.9344 MHz)
48 XTAO O System clock output terminal (16.9344 MHz)
49 XVSS — Ground terminal (for master clock)
50 AVDD1 — Power supply terminal (analog system)
51 AOUT1 O L-ch analog audio signal output
52 VREFL O L-ch reference voltage output terminal
53, 54 AVSS1, AVSS2 — Ground terminal (analog system)
55 VREFR O R-ch reference voltage output terminal
56 AOUT2 O R-ch analog audio signal output
57 AVDD2 — Power supply terminal (analog system)
58 TES1 I Input terminal for the test (normally: fixed at “L”)
59 TEST I Input terminal for the test (normally: fixed at “L”)
60 VSS1 — Ground terminal (digital system)
61 LRMU O
62 DOUT O Digital audio signal output Not used (open)
63 ATSK I/O Input/output terminal for anti-shock Not used (open)
64 DFCT I/O Defect signal input/output terminal Not used (open)
65 FOK O Focus OK signal output to the system controller (IC801) “L”: NG, “H”: OK
66 MIRR I/O Defect signal input/output terminal Not used (open)
67 COUT I/O Numbers of track counted signal input/output terminal Not used (open)
68 C2PO O C2PO signal output terminal Not used (open)
69 GFS O GFS signal output terminal Not used (open)
70 XUGF O XUGF signal output terminal Not used (open)
71 XPCK O XPCK signal output terminal Not used (open)
72 VDD1 — Power supply terminal (digital system)
73 PCO O Charge pump output for master PLL
74 FILI I Filter input for master PLL
75 FILO O Filter output for master PLL
76 CLTV I VCO1 control voltage input terminal for multiplier
77 VCTL I VCO2 control voltage input terminal for broad-band EFM PLL
78 VPCO O Charge pump output terminal for broad-band EFM PLL
79 AVSS3 — Ground terminal (analog system)
80 ASYO O EFM full-swing output terminal
81 ASYI I Asymmetry comparator voltage input terminal
82 BIAS I Asymmetry circuit constant current input terminal
83 AVDD3 — Power supply terminal (analog system)
84 RFAC I EFM signal input from the optical pick-up
85 AVDD0 — Power supply terminal (analog system)
86 IGEN I Stabilized current input for operational amplifiers
87 AVSS0 — Ground terminal (analog system)
88 RFDC I RF signal input from the optical pick-up
89 E I E signal input from the optical pick-up
90 F I F signal input from the optical pick-up
91 B I B signal input from the optical pick-up
92 A I A signal input from the optical pick-up
93 VC I Middle point voltage input terminal Not used (fixed at “L”)
94 VSS3 — Ground terminal (digital system)
95 FRDR O Focus servo drive signal (–) output to the TB2125F (IC401)
PDM signal output for R-ch headphone to the headphone amplifier (IC302)
Not used (open)
Muting on/off control signal output to the audio line and the headphone amplifier (IC302)
“H”: muting on
11
Loading...