Sony CDP-CX220 User Manual

Compact Disc Player

3-862-563-11 (1)

Operating Instructions

CDP-CX240 CDP-CX220

 1998 by Sony Corporation

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.

For the customers in the United States

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving

antenna.

– Increase the separation between the

equipment and receiver.

– Connect the equipment into an outlet

on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced

radio/TV technician for help.

CAUTION

You are cautioned that any changes or modification not expressly approved in this manual could void your authority to operate this equipment.

Owner’s Record

The model and serial numbers are located at the rear of the unit. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product.

Model No. CDP-CX240/CDP-CX220 Serial No. _________________________

(Except for the customers in the United States)

The following caution label is located inside the unit.

This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.

This equipment is intended for home entertainment purposes only. The warranty shall be invalidated if used in commercial environments, such as by disc jockeys, etc., even within the Warranty Period.

Welcome!

Thank you for purchasing the Sony Compact Disc Player. Before operating the unit, please read this manual thoroughly and retain it for future reference.

About This Manual

The instructions in this manual are for models CDP-CX240 and CDP-CX220. The CDP-CX240 is the model used for illustration purposes. Any difference in operation is clearly indicated in the text, for example, “CDP-CX240 only.”

Conventions

• Instructions in this manual describe the controls on the player. You can also use the controls on the remote if they have the same or similar names as those on the player.

• The following icons are used in this manual:

Indicates that you can do the task using the remote.

Indicates hints and tips for making the task easier.

TABLE OF CONTENTS

Getting Started

Unpacking............................................................................................................................ 4

Hooking Up the System..................................................................................................... 4

Connecting Another CD Player (CDP-CX240 only) ...................................................... 6

Inserting CDs....................................................................................................................... 7

Playing a CD......................................................................................................................... 10

Playing CDs

Using the Display ............................................................................................................ 12

Locating a Specific Disc .................................................................................................. 13

Specifying the Next Disc to Play ................................................................................... 15

Locating a Specific Track or a Point in a Track ............................................................ 15

Playing Repeatedly........................................................................................................... 16

Playing in Random Order (Shuffle Play) ...................................................................... 16

Creating Your Own Program (Program Play).............................................................. 17

Playing Using a Timer (CDP-CX240 only) .................................................................... 19

Controlling Another CD Player (Advanced Mega Control) (CDP-CX240 only)..... 20

Fading In or Out (CDP-CX240 only).............................................................................. 21

Playing Alternately (No-Delay Play/X-Fade Play) (CDP-CX240 only) ................... 22

Storing Information About CDs (Custom Files)

What You Can Do With the Custom Files .................................................................... 23

Labeling Discs (Disc Memo)............................................................................................ 23

Storing Custom File Information Using a keyboard (CDP-CX240 only).................. 26

Storing Specific Tracks (Delete Bank) ............................................................................ 26

Grouping Discs (Group File)........................................................................................... 27

Storing Your Favorite Tracks (Hit List) (CDP-CX240 only) ....................................... 28

Additional Information

Precautions ........................................................................................................................ 30

Notes on CDs..................................................................................................................... 30

Troubleshooting ................................................................................................................ 31

Specifications ..................................................................................................................... 31

Index........................................................................................................................... Back cover

Getting StartedGetting Started

Unpacking

Check that you received the following items:

• Audio cord (1)

• Remote commander (remote) (1)

• Sony SUM-3 (NS) batteries (2)

• CD booklet holders (2) and label (1)

How to use the CD booklet holder

The CD booklet holder helps you locate the disc easily. After you have inserted discs into the player, you can put the CD booklet (which comes with a CD) into the supplied holder. Put two CD booklets facing back to back into a pocket. Stick the number label on each pocket, matching the number of the disc slot where you have inserted the disc. You can put up to 200 CD booklets into the holders.

Inserting batteries into the remote

You can control the player using the supplied remote. Insert two size AA (R6) batteries by matching the + and – on the batteries to the diagram inside the battery compartment. Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position. When using the remote, point it at the remote sensor g on the player.

Hooking Up the System

Overview

This section describes how to hook up the CD player to an amplifier. Be sure to turn off the power of each component before making the connections.

S-LINK/ CONTROL A1

To an AC outlet

To line output (L)

To audio input

COMMAND MODE

To line output (R)

DIGITAL OUT (OPTICAL)

CD player

Amplifier

: Signal flow

To an AC outlet

What cords will I need?

Audio cord (1) (supplied)

When to replace batteries

With normal use, the batteries should last for about six months. When the remote no longer operates the player, replace all the batteries with new ones.

White

(L)

Red

(R)

White

(L)

Red

(R)

Notes

• Do not leave the remote near an extremely hot or humid place.

• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.

• Do not expose the remote sensor to direct sunlight or lighting apparatuses. Doing so may cause a malfunction.

• If you do not use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion.

Getting Started

Playing CDsGetting Started

Hookups

When connecting the audio cord, be sure to match the color-coded cord to the appropriate jacks on the components: Red (right) to Red and White (left) to White. Be sure to make connections firmly to avoid hum and noise.

CD player

LINE2ND CD

IN OUT

• If you have a digital component such as a digital amplifier, D/A converter, DAT or MD

Connect the component via the DIGITAL OUT (OPTICAL) connector using an optical cable (not supplied). Take off the cap and plug in the optical cable.

POC-15

Optical cable (not supplied)

Amplifier

INPUT

L R

When using another Sony CD player together with

this player

You can make the supplied remote effective only for this player.

• When using the player equipped with the COMMAND MODE selector: Set the COMMAND MODE selector of this player to CD 1 and that of another player to CD 2 or CD 3. Then set the CD 1/2/3 switch on the remote supplied for each player accordingly.

• When using the player not equipped with the COMMAND MODE selector: The command mode of the player without the COMMAND MODE selector is set to CD 1. Set the COMMAND MODE selector of this player to CD 2, and set the CD 1/2/3 switch on the remote to CD 2.

Setting the voltage selector (voltage selector equipped models only)

Check that the voltage selector on the rear panel of the player is set to the local power line voltage. If not, set the selector to the correct position using a screwdriver before connecting the AC power cord to a wall outlet.

CD player

DIGITAL OUT

OPTICAL

Digital component

DIGITAL INPUT

OPTICAL

Note

When you connect via the DIGITAL OUT (OPTICAL) connector, noise may occur when you play CD software other than music, such as a CD-ROM.

If you have a Sony component with the CONTROL A1 jack

Connect the component via the CONTROL A1 jack. You can simplify the operation of audio systems composed of separate Sony components. For details, refer to the supplementary “S-LinkTM/CONTROL-A1 Control System” instructions.

220 - 240 V110 - 120 V

Connecting the AC power cord

Connect the AC power cord to a wall outlet.

Note on placement

Be sure to place the player on a horizontal place. If the player is slanted, it may cause malfunction or damage the player.

Getting Started

Connecting Another CD Player (CDP-CX240 only)

What cords will I need?

• Audio cord (1) (Use the cord supplied with the player to be connected.)

• Monaural (2P) mini-plug cord (1) (not supplied)

If you have a Sony CD player equipped with the CONTROL A1 jack and the command mode of that player can be set to CD 3, you can control that player as the second player with this unit. After connecting this unit and an amplifier, follow the procedure below. Be sure to turn off the power of each player before making this connection.

To LINE OUT

To an AC outlet

To 2ND CD IN

To audio output

COMMAND MODE

CDP-CX240

To S-LINK/CONTROL A1

CDP-CX200, etc.

To CONTROL A1

1 Connect the players with an audio cord (see also

“Hookups” on page 5).

CDP-CX240

LINE2ND CD

IN OUT

CDP-CX200, etc.

LINE OUT

L R

2 Connect the players with a monaural (2P) mini-

plug cord.

CDP-CX240

S-LINK

CONTROL A1

CDP-CX200, etc.

CONTROL A1

For details on this connection, refer to the supplementary “S-Link

/CONTROL-A1 Control

System” instructions.

3 Set the COMMAND MODE selector of each

player. Set the COMMAND MODE selector of this player to CD 1 or CD 2, and set that of the second player to CD 3.

COMMAND MODE

132

To an AC outlet

For details on how to operate the second player,

To audio input

Amplifier

see “Controlling Another CD Player” on page 20 and “Playing Alternately” on page 22.

4 Connect the AC power cord of both players to AC

outlets.

: Signal flow

To an AC outlet

Notes

• Do not connect a player other than that you use as the second player to the 2ND CD IN jacks of this player.

• When connecting a second CD player, do not connect the DIGITAL OUT (OPTICAL) connector of this unit to the amplifier.

Inserting CDs

You can insert up to 200 discs into this player.

Getting Started

Playing CDsGetting Started

3 Turn the JOG dial until you find the disc slot

where you want to insert a disc, while checking the disc number (written beside every slot and also indicated in the display).

I/u

§ OPEN/CLOSE

Playing position

Rotary table

Loading position

JOG

1 Press I/u to turn on the player. 2 Open the front cover by pressing § OPEN/

CLOSE.

Disc number

Disc slot at the loading position

The disc number at the loading position appears in the display.* If the disc has the Disc Memo (see page 23), the Disc Memo appears instead of the disc number. As you turn the JOG dial, the disc number or the Disc Memo changes.

ALL

DISCS

CD1

DISC

*DISC-20*

Disc number or the Disc Memo

You can classify discs into eight groups by using the Group File function. This feature lets you easily find the disc you want to play. For details, see “Grouping Discs” on page 27.

* If you have already inserted discs, the disc number at

the playing position appears. When you turn the JOG dial, the displayed disc number changes to the one at the loading position.

(Continued)

Getting Started

4 Insert a disc with the label side facing right.

With the label side facing right

After inserting the disc, you can input the original disc titles instead of the disc numbers (see “Labeling Discs” on page 23) to locate it easily when you start playing.

ALL DISCS

CD1

DISC

SONYHITS

5 Repeat Steps 3 and 4 to insert more discs. 6 Close the front cover by pressing § OPEN/

CLOSE.

The supplied CD booklet holders help you locate a disc

You can store up to 200 CD booklets. Insert a booklet and stick the number label on the film of a pocket and the booklet so that you can locate the disc easily.

Notes

• Do not insert an empty 8 cm (3-inch) CD adaptor (CSA-8). It may damage the player.

• Do not attach anything such as seals or sleeves to CDs. It may damage the player or the disc.

• If you drop a disc into the player and the CD won’t go into the slot correctly, consult your nearest Sony dealer.

• When transporting the player, remove all discs from the player.

• Make sure you have inserted the disc into each slot at a right angle to the rotary table. If the disc is not put in straight, it may damage the player or the disc.

• Make sure the rotary table comes to a complete stop before inserting or removing discs. The front panel closes automatically when you press

·. Be careful not to put your hand into the player after pressing · otherwise your hand may be caught in the front panel.

The rotary table turns and the disc slot at the loading position is set to the playing position. Always close the front cover except when you insert or remove discs.

Removing CDs

After following Steps 1 to 3 of “Inserting CDs” on page 7, remove the discs. Then close the front cover.

Getting Started

Playing CDsGetting Started

Basic Operations

Playing a CD

STANDBY

I / u

CONTINUE

TIMER

OFF PLAY

GROUP 1

KEY BOARD

GROUP 5

KEYBOARD

• See pages 4 – 5 for the hookup

information.

• Make sure you have inserted the

discs correctly as indicated on pages 7 – 8.

• You can play all the tracks on a

disc in the original order (Continuous Play). You can also play up to 200 discs consecutively.

You can turn on the player by pressing I/u on the remote Z

SHUFFLE

GROUP 2

GROUP 6

PROGRAM

GROUP 3

GROUP 7

REPEAT

GROUP 4

GROUP 8

X-FADE

4/5

INPUT

MEMO SEARCH

AMS

DISC/CHARACTER

PUSH ENTER

CHECK CLEAR

TIME/TEXT

HIT LIST

GROUP FILE

MEGA CONTROL

FADER NO DELAY

OPEN/CLOSE

Turn on the amplifier and select the CD player position.

Press I/u to turn on the player.

Press CONTINUE to select ALL DISCS or 1 DISC Continuous

Play mode.

Each time you press CONTINUE, “ALL DISCS” or “1 DISC” appears in the display.

When you select

ALL DISCS

1 DISC

The player plays

All discs in the player consecutively in the order of disc number. Empty disc slots are skipped.

Only one disc you have selected

Turn the JOG dial until the disc number or the Disc Memo (see page 23) you want appears in the display to select the first disc

(ALL DISCS) or the disc you want (1 DISC).

ALL DISCS

CD1

DISC

*DISC-20*

+ 22 hidden pages