Sony CCD-TR618, CCD-TR718, CCD-TR728, CCD-TR818, CCD-TRV49 Service manual

CCD-TR618/TR618E/TR718E/TR728E/TR818

CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/

TRV78/TRV78E/TRV88/TRV98/TRV98E

RMT-708

SERVICE MANUAL

Ver 1.2 2001. 11

Photo : CCD-TRV98E

B MECHANISM

NTSC model : CCD-TR618/TR818/TRV49/TRV58/

TRV68/TRV78/TRV88/TRV98

P AL model : CCD-TR618E/TR718E/TR728E/TRV49E/

TRV58E/TRV59E/TRV78E/TRV98E

SPECIFICATIONS

CCD-TR818/TRV58/TRV68/TRV88/TRV98

Canadian Model

CCD-TR818/TRV58/TRV68/TRV98

US Model

AEP Model

CCD-TR718E/TR728E/TRV58E/

TRV59E/TRV78E/TRV98E

CCD-TR618/TR618E/TR818/TRV49/

TRV49E/TRV58/TRV68/TRV78/

TRV78E/TRV88/TRV98/TRV98E

CCD-TR618E/TRV49E/TRV78E/TRV98E

CCD-TR618E/TRV49/TRV49E/TRV78/

Australian Model

Hong Kong Model

CCD-TRV49/TRV49E/TRV78/

CCD-TR618E/TRV49E/TRV98E

CCD-TR818/TRV58/TRV98

Argentina Model

CCD-TRV49/TRV78/TRV98

For MECHANISM ADJUSTMENT, refer to the “8mm Video MECHANICAL ADJUSTMENT MANUAL

UK Model

E Model

TRV78E/TRV98/TRV98E

Tourist Model

TRV78E/TRV98/TRV98E

Chinese Model

Brazilian Model

CCD-TR818/TRV58

Korea Model

” (9-973-801-11).

— Continued on next page —

VIDEO CAMERA RECORDER

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer.

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS P AR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMA TIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges.

2. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair . Point them out to the customer and recommend their replacement.

4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.

5. Check the B+ voltage to see it is at the values specified.

6. Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270˚C during repairing.

• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering or unsoldering.

— 2 —

• SUPPLIED ACCESSORIES

Check that the following accessories are supplied with your camcorder.

• Abbreviation HK : Hong Kong model JE : Tourist model BR : Brazilian model

— 3 —

Remark

VF-129 : B/W EVF

VF-141 : Color EVF

LB-062 : Color EVF

CCD-

TR V98E

CCD-

TRV98

CCD-

TRV88

CCD-

TR V78E

CCD-

TRV78

CCD-

TRV68

CCD-

TR V59E

CCD-

TR V58E

CCD-

TRV58

AEP,UK,

E,HK,AUS,

JE,CN

US,CND,

E,HK,KR,

JE,BR

US,E

AEP,UK,

E,HK,AUS,

JE

E,HK,

KR,JE

US,CND,

E

AEP,UK

US,CND,

E,BR,

AR

PAL

RMT-708

NTSC

XX

PAL

RMT-708

NTSC

✕✕

RMT-708

PAL

✕✕

NTSC

✕✕

3.5 inch 123K

560×

3 inch

a

1/4 inch

a

460×

B/W

a

CD-281

VF-129

MI-041

PD-131

✕✕

CF-1000 block

560×

61K

2.5 inch

20×

460×

1/6 inch

✕✕

CCD-

TR V49E

CCD-

TRV49

CCD-

TR818

CCD-

TR728E

CCD-

TR718E

CCD-

TR618E

CCD-

TR618

E,HK,

AUS,JE,

CN

E,HK,

KR,JE

US,CND,

E,BR,

AR

AEP,UK

E,HK,

AUS,CN

E

PAL

RMT-708

NTSC

✕✕

RMT-708

PAL

✕✕

NTSC

450×

460×

560×

460×

450×

Digital

Optical

1/4 inch

✕✕

1/6 inch

size

✕✕

pixel

a

Color

✕✕

B/W

✕✕

CF-077✕✕MI-040

CD-286

a

CD-

CF-

VF-141

VF-129

PD-

VF-

MI-

LB-062

✕✕

LB-

Model

Destination

Table for difference of function

Color system

Remote commander

Lens

CCD imager size

LCD

View finder

Steady shot

Headphone jack

LASER LINK

Video Light

— 4 —

Board

CND : Canadian model

HK : Hong Kong model

KR : Korea model

• Abbreviation

JE : Tourist model

AUS : Australian model

CN : Chinese model

BR : Brazilian model

AR : Argentina model

TABLE OF CONTENTS

SERVICE NOTE

1. POWER SUPPLY DURING REPAIRS ·····························8

2. TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT) ································································8

SELF-DIAGNOSIS FUNCTION

1. Self-diagnosis Function ······················································9

2. Self-diagnosis Display························································ 9

3. Service Mode Display ························································ 9

3-1. Display Method ·································································· 9 3-2. Switching of Backup No. ··················································· 9 3-3. End of Display···································································· 9

4. Self-diagnosis Code Table ················································10

1. GENERAL

Checking supplied accessories ··················································1-1 Quick Start Guide ······································································ 1-1 Getting started

Using this manual ··································································1-1 Step 1 Preparing the power supply ········································1-2 Installing the battery pack····················································1-2 Charging the battery pack ····················································1-2 Connecting to the mains ······················································1-3 Step 2 Setting the date and time ············································ 1-4 Step 3 Inserting a cassette······················································1-4

Recording –Basics

Recording a picture································································1-5 Shooting backlit subjects –BACK LIGHT ··························1-7 Shooting in the dark –NightShot ·········································1-7 Superimposing the date and time on pictures ······················1-7 Checking the recording –END SEARCH······························1-8

Playback –Basics

Playing back a tape ································································ 1-8 Viewing the recording on TV ················································ 1-9

Advanced Recording Operation

Using the wide mode ·····························································1-9 Using the fader function ······················································1-10 Using special effects –Picture effect····································1-11 Using the PROGRAM AE function ·····································1-11 Adjusting the exposure manually ········································1-12 Focusing manually······························································· 1-12 Superimposing a title ··························································· 1-13 Making your own titles ························································1-13 Using the built-in light························································· 1-14

Editing

Dubbing a tape ·····································································1-15

Customizing Y our Camcorder

Changing the menu settings·················································1-15

Troubleshooting

Types of trouble and their solutions····································· 1-17 Self-diagnosis display ··························································1-18 Warning indicators and messages ········································1-18

Additional Information

Usable cassettes and playback modes··································1-19 About “InfoLITHIUM” battery ··········································· 1-19 Using your camcorder abroad··············································1-20 Maintenance information and precautions···························1-20

Quick Reference

Identifying the parts and controls ········································1-22

2. DISASSEMBLY

2-1. VIDEO LIGHT (VIDEO LIGHT MODEL) ···················2-2 2-2. LCD SECTION (PD-131 BOARD) (TRV MODEL)······2-3 2-3. FRONT PANEL SECTION, MI-040/041 BOARD ········2-4 2-4. CABINET (L) SECTION················································2-5

2-5. CABINET (R) SECTION (CF-077 BOARD)

(TR MODEL) ··································································2-6

2-6. CABINET (R) SECTION [CONTROL SWITCH

BLOCK (CF-1000)] (TRV MODEL)······························2-7 2-7. VF-129 BOARD (B/W EVF MODEL)···························2-8 2-8. VF-141, LB-062 BOARDS

(COLOR EVF MODEL/TR818)·····································2-9 2-9. BATTERY PANEL SECTION

(BATTERY TERMINAL BOARD) ······························2-10 2-10. LENS SECTION ···························································2-11 2-11. VC-251 BOARD ···························································2-11 2-12. MECHANISM DECK ···················································2-14 2-13. HINGE ASSEMBLY (TRV MODEL) ··························2-14 2-14. CIRCUIT BOARDS LOCATION ·································2-15 2-15. FLEXIBLE BOARDS LOCATION ······························ 2-16

3. BLOCK DIAGRAMS

3-1. OVERALL BLOCK DIAGRAM (1/2) ···························3-3 3-2. OVERALL BLOCK DIAGRAM (2/2) ···························3-5 3-3. CAMERA/VIDEO BLOCK DIAGRAM (1/2) ···············3-7 3-4. CAMERA/VIDEO BLOCK DIAGRAM (2/2) ···············3-9 3-5. VTR/CAMERA CONTROL BLOCK DIAGRAM·······3-11 3-6. SERVO BLOCK DIAGRAM········································3-13 3-7. MODE CONTROL BLOCK DIAGRAM·····················3-15 3-8. AUDIO BLOCK DIAGRAM ········································3-17 3-9. LCD BLOCK DIAGRAM ············································ 3-19 3-10. B/W EVF BLOCK DIAGRAM ····································3-21 3-11. COLOR EVF BLOCK DIAGRAM ······························3-23 3-12. POWER BLOCK DIAGRAM (1/2)······························ 3-25 3-13. POWER BLOCK DIAGRAM (2/2)······························ 3-27

4. PRINTED WIRING BOARDS AND

SCHEMATIC DIAGRAMS

4-1. FRAME SCHEMATIC DIAGRAM (1/2)·······················4-1

FRAME SCHEMATIC DIAGRAM (2/2)·······················4-3 4-2. PRINTED WIRING BOARDS AND

SCHEMATIC DIAGRAMS ············································4-5

• CD-281/286 (CCD IMAGER) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM ······························4-7

• MI-040/041 (STEADY SHOT, MIC AMP, IR DRIVE) PRINTED WIRING BOARD ·························4-9

• MI-040/041 (STEADY SHOT, MIC AMP)(1/2) SCHEMATIC DIAGRAM ····························4-11

• MI-040/041 (IR DRIVE)(2/2) SCHEMATIC DIAGRAM ····························4-13

• PD-131 (RGB, TIMING GENERATOR, BACK LIGHT) PRINTED WIRING BOARD ······················· 4-15

• PD-131 (RGB, TIMING GENERATOR)(1/2) SCHEMATIC DIAGRAM ····························4-19

• PD-131 (BACK LIGHT)(2/2) SCHEMATIC DIAGRAM ····························4-21

• VF-129 (B/W EVF) PRINTED WIRING BOARD ······················· 4-24

• VF-129 (B/W EVF) SCHEMATIC DIAGRAM ····························4-25

• VF-141 (COLOR EVF) PRINTED WIRING BOARD ······················· 4-27

• VF-141 (COLOR EVF) SCHEMATIC DIAGRAM ····························4-29

• LB-062 (EVF BACK LIGHT) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM ····························4-31

• CONTROL SWITCH BLOCK (CF-1000) SCHEMATIC DIAGRAM ····························4-33

• CF-077 (SWITCH) PRINTED WIRING BOARD ······················· 4-35

— 5 —

• CF-077 (SWITCH) SCHEMATIC DIAGRAM ····························4-37

• VC-251 (CAMERA PROCESSOR, Y/C PROCESSOR,

FOCUS/ZOOM MOTOR DRIVE, REC/PB AMP, LINE I/O AMP, SERVO, MODE CONTROL, HI CONTROL, AUDIO, DC/DC CONVERTER, CONNECTOR)

PRINTED WIRING BOARD ······················· 4-39

• VC-251 (CAMERA PROCESSOR AMP)(1/11) SCHEMATIC DIAGRAM ····························4-43

• VC-251 (Y/C PROCESSOR)(2/11) SCHEMATIC DIAGRAM ····························4-45

• VC-251 (FOCUS/ZOOM MOTOR DRIVE)(3/11) SCHEMATIC DIAGRAM ····························4-47

• VC-251 (REC/PB AMP)(4/11) SCHEMATIC DIAGRAM ····························4-49

• VC-251 (LINE I/O AMP)(5/11) SCHEMATIC DIAGRAM ····························4-51

• FP-249 (S/T REEL SENSOR, TAPE TOP),

FP-356 (TAPE END), FP-355 (TAPE LED)

FLEXIBLE BOARDS···································4-52

• VC-251 (SERVO)(6/11) SCHEMATIC DIAGRAM ····························4-53

• VC-251 (MODE CONTROL)(7/11) SCHEMATIC DIAGRAM ····························4-55

• VC-251 (HI CONTROL)(8/11) SCHEMATIC DIAGRAM ····························4-57

• VC-251 (AUDIO)(9/11) SCHEMATIC DIAGRAM ····························4-59

• VC-251 (DC/DC CONVERTER)(10/11) SCHEMATIC DIAGRAM ····························4-61

• VC-251 (CONNECTOR)(11/11) SCHEMATIC DIAGRAM ····························4-63

• FP-257 (VIDEO LIGHT, S VIDEO) FLEXIBLE BOARD·····································4-65

4-3. WAVEFORMS ······························································4-66 4-4. MOUNTED PARTS LOCATION ·································4-70

5. ADJUSTMENTS

1. Before starting adjustment···············································5-2 1-1. Adjusting items when replacing main parts and boards·· 5-2 5-1. CAMERA SECTION ADJUSTMENT··························· 5-4 1-1. PREPARATIONS BEFORE ADJUSTMENT

(CAMERA SECTION) ···················································5-4 1-1-1.List of Service Tools························································ 5-4 1-1-2.Preparations ·····································································5-5 1-1-3.Precaution ········································································5-8

1. Setting the Switch····························································5-8

2. Order of Adjustments ······················································ 5-8

3. Subjects ··········································································· 5-8 1-2. INITIALIZATION OF D, E, F, 7 PAGE DATA ··············5-9

1. Initializing the D, E, F, 7 Page Data ································5-9

2. Modification of D, E, F, 7 Page Data ······························5-9

3. D Page Table····································································5-9

4. F Page table ···································································5-10

5. E Page Table ·································································· 5-12

6. 7 Page Table···································································5-13 1-3. CAMERA SYSTEM ADJUSTMENTS························5-14

1. Lens T ype Input····························································· 5-14

2. HALL Adjustment ·························································5-14

3. Flange Back Adjustment (Using Minipattern Box)·······5-15

4. Flange Back Adjustment

(Using Flange Back Adjustment Chart and Subject

More Than 500m Away)················································5-16 4-1. Flange Back Adjustment (1)··········································5-16 4-2. Flange Back Adjustment (2)··········································5-16

5. Flange Back Check························································5-17

6. Picture Frame Setting ···················································· 5-18

7. Color Reproduction Adjustment····································5-19

8. Auto White Balance & LV Standard Data Input ··········· 5-20

9. Auto White Balance Adjustment ···································5-21

10. White Balance Check ···················································· 5-22

11. Angular Velocity Sensor Sensitivity Adjustment (CCD-TR818/TRV68/TRV78/TRV78E/TRV88/TRV98/ TRV98E)········································································5-23

1-4. COLOR ELECTRONIC VIEWFINDER SYSTEM

ADJUSTMENT (CCD-TR818) ···································· 5-24

1. RGB AMP Adjustment (VF-141 board)························5-25

2. Contrast Adjustment (VF-141 board)····························5-25

3. Backlight Consumption Current Adjustment (LB-062 board)······························································ 5-26

4. White Balance Adjustment (VF-141 board)··················5-26

1-5. MONOCHROME ELECTRONIC VIEWFINEDER

SYSTEM ADJUSTMENT (CCD-TR618/TR618E/TR718E/TR728E/TR V49/ TR V49E/TR V58/TR V58E/TR V59E/TRV68/TR V78/ TR V78E/TR V88/TR V98/TRV98E)·······························5-27

1-5-1.Horizontal Slant Check ·················································5-27 1-5-2.Centering Adjustment····················································5-27 1-5-3.Focus Adjustment ··························································5-27 1-5-4.Aberration Adjustment ··················································5-28 1-5-5.Horizontal Amplitude Adjustment (VF-129 board) ······5-28 1-5-6.Vertical Amplitude Adjustment (VF-129 board) ···········5-29 1-5-7.Brightness Adjustment (VF-129 board) ························5-29 1-5-8.Horizontal Amplitude, V ertical Amplitude,

Focus Check ··································································5-29

1-6. LCD SYSTEM ADJUSTMENT

(CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/ TR V68/TRV78/TRV78E/TR V88/ TRV98/TRV98E) ····5-30

1. LCD T ype Check ···························································5-30

2. VCO Adjustment (PD-131 board)·································5-31

3. RGB AMP Adjustment (PD-131 board)························5-31

4. Contrast Adjustment (PD-131 board)····························5-32

5. COM AMP Adjustment (PD-131 board)·······················5-32

6. V-COM Adjustment (PD-131 board) ····························5-33

7. White Balance Adjustment (PD-131 board)··················5-33

5-2. MECHANISM SECTION ADJUSTMENT··················5-34 2-1. ADJUSTMENT REMOTE COMMANDER ················5-34 2-2. OPERATING WITHOUT CASSETTE ························5-34 2-3. TAPE PATH ADJUSTMENT········································5-34

1. Preparations for Adjustment··········································5-34

5-3. VIDEO SECTION ADJUSTMENTS ···························5-35 3-1. PREPARATIONS BEFORE ADJUSTMENTS ············5-35 3-1-1.Equipment to Required··················································5-35 3-1-2.Precautions on Adjusting···············································5-36 3-1-3.Adjusting Connectors ····················································5-37 3-1-4.Connecting the Equipment ············································5-37 3-1-5.Alignment T ape ·····························································5-38 3-1-6.Output Level and Impedance·········································5-39 3-1-7.Recording Mode (Standard 8/Hi8) switching ··············· 5-39 3-2. SYSTEM CONTROL SYSTEM ADJUSTMENT········ 5-40

1. Initialization of D, E, F, 7 Page Data·····························5-40

3-3. SERVO SYSTEM ADJUSTMENT······························· 5-40

1. CAP FG Offset Adjustment (VC-251 board) ················5-40

2. Switching Position Adjustment (VC-251 Board)··········5-40

3-4. VIDEO SYSTEM ADJUSTMENTS····························· 5-41

1. 28 MHz Origin Oscillation Adjustment (VC-251 board) ·····························································5-41

2. AFC fo Adjustment (VC-251 board)·····························5-42

3. Filter fo Adjustment (VC-251 board)····························5-42

4. Y OUT Level Adjustment (VC-251 board) ···················5-43

5. C OUT Level Adjustment (VC-251 board) ··················· 5-43

6. REC Y Current Adjustment (VC-251 board) ················5-44

7. REC C/AFM Current Adjustment ·································5-45

7-1. Preparations ···································································5-45

— 6 —

7-2. REC C Current Check (VC-251 board) ························5-45 7-3. REC AFM Current Adjustment (VC-251 board) ··········5-46 7-4. Processing after completed adjustment ·························5-46 3-5.

IR TRANSMITTER ADJUSTMENTS (CCD-TRV98)···

1.

IR Video Carrier Frequency Adjustment (MI-041 board)·

2. IR Video Deviation Adjustment (MI-041 board)···········5-47

3. IR Audio Deviation Adjustment (MI-041 board) ··········5-48 3-6. AUDIO SYSTEM ADJUSTMENTS ····························5-49

1. 1.5MHz Deviation Adjustment (VC-251 board) ··········· 5-49

2. BPF fo Adjustment (VC-251 board) ·····························5-49 5-4. SERVICE MODE··························································5-50 4-1. ADJUSTMENT REMOTE COMMANDER ················5-50

1. Using the Adjustment Remote Commander··················5-50

2. Precautions Upon Using the Adjustment Remote Commander ···································································5-50

4-2. DATA PROCESS···························································5-51 4-3. SERVICE MODE··························································5-52

1. Test Mode Setting··························································5-52

2. Emergency Memory Address ········································5-53

2-1. EMG code (Emergency code) ·······································5-53 2-2. MSW codes ···································································5-54

3. Bit V alue Discrimination ··············································· 5-55

4. Switch check (1) ····························································5-55

5. Switch check (2) ····························································5-55

6. Switch check (3) ····························································5-55

7. Switch check (4) ····························································5-56

8. Record of Use check······················································5-56

9. Record of Self-diagnosis check ·····································5-57

5-47 5-47

6. REPAIR PARTS LIST

6-1. EXPLODED VIEWS ······················································6-1 6-1-1.OVERALL SECTION·····················································6-1 6-1-2.CABINET (L) SECTION················································6-2 6-1-3.B/W EVF SECTION (TR618/TR618E/TR718E/TR728E/

TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/ TRV78/TRV78E/TRV88/TRV98/TRV98E)····················6-3

6-1-4.COLOR EVF SECTION (TR818) ··································6-4 6-1-5.CABINET (R) SECTION ···············································6-5 6-1-6.LCD SECTION (TRV MODEL)(TRV49/TRV49E/

TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/ TRV88/TRV98/TRV98E) ················································6-6

6-1-7.LENS SECTION ····························································· 6-7 6-1-8.CASSETTE COMPARTMENT ASSEMBLY ················6-8 6-1-9.LS CHASSIS BLOCK ASSEMBLY·······························6-9 6-1-10. MECHANISM CHASSIS ASSEMBLY·····················6-10 6-2. ELECTRICAL PARTS LIST ········································6-11

* Color reproduction frame is shown on page 239.

— 7 —

SERVICE NOTE

1. POWER SUPPLY DURING REPAIRS

In this unit, about 10 seconds after power is supplied (8.4V) to the battery terminal using the service power cord (J-6082-223-A), the power is shut off so that the unit cannot operate. This following method is available to prevent this.

Method:

Use the DC IN terminal. (Use the AC power adaptor.)

2. TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)

1 Refer to 2-3. to remove the front panel assembly. 2 Refer to 2-5 (TR model). or 2-6 (TRV model). to remove the

cabinet (R) assembly.

3 Open the control switch block (FK-1000). 4 Refer to 2-4. to remove the cabinet (L) assembly. 5 Disconnect CN704 (8P) of VC-251 board. 6 Add +5V from the DC POWER SUPPLY and unload with a

pressing the cassette compartment.

8

Let go your hold the cassette compartment and rise the cassette compartment to take out a cassette.

7

Pull the timing belt in the direction of

A

arrow the cassette compartment (take care not to damage) to adjust the bending of a tape.

A

with a pincette while pressing

Pincette

Timing belt

A

Press the cassette compartment not to rise the cassette compartment

[DC power supply]

(+5V)

Loading motor

Timing belt

Disconnect CN704 of VC-251 board.

Adjust the bending of a tape

— 8 —

SELF-DIAGNOSIS FUNCTION

1. Self-diagnosis Function

When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the viewfinder or LCD or Display window what to do. This function consists of two display; self-diagnosis display and service mode display. Details of the self-diagnosis functions are provided in the Instruction manual.

Viewfinder or LCD Display window

C : 3 1 : 1 1

Repaired by:

C : Corrected by customer H : Corrected by dealer E : Corrected by service

engineer

Blinks at 3.2Hz

C

Indicates the appropriate step to be taken. E.g.

31 ....Reload the tape.

32 ....Turn on power again.

3 1

Block

1 1

C : 3 1 : 11

Refer to page 10 and 11. Self-diagnosis Code Table.

2. Self-diagnosis Display

When problems occur while the unit is operating, the counter of the viewfinder or LCD or Display window shows a 4-digit display consisting of an alphabet and numbers, which blinks at 3.2 Hz. This 5-character display indicates the “repaired by:”, “block” in which the problem occurred, and “detailed code” of the problem.

(TR model)

Display window

(TRV model)

Detailed Code

3. Service Mode Display

The service mode display shows up to six self-diagnosis codes shown in the past.

3-1. Display Method

While pressing the “STOP” key, set the switch from OFF to “VTR or PLAYER”, and continue pressing the “STOP” key for 5 seconds continuously. The service mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis codes.

Viewfinder or LCD

[3] C : 3 1 : 1 1

Lights up

[3]

Backup No.

Order of previous errors

C : 3 1 : 1 1

Self-diagnosis Codes

3-2. Switching of Backup No.

By rotating the control dial, past self-diagnosis codes will be shown in order. The backup No. in the [] indicates the order in which the problem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.) [1] : Occurred first time [4] : Occurred fourth time [2] : Occurred second time [5] : Occurred fifth time [3] : Occurred third time [6] : Occurred the last time

Display window

3 C : 3 1 : 11

Control dial

3-3. End of Display

Turning OFF the power supply will end the service mode display.

Note: The “self-diagnosis display” data will be backed up by the built-in rechargeable lithium battery (CF-1000 block/CF-077

board BT101). When the cabinet (R) assembly is disconnected, the “self-diagnosis displa y” data will be lost by initialization.

— 9 —

4. Self-diagnosis Code Table

Self-diagnosis Code

Function

Repaired by:

C C C

C

C C

C C C C C C C C C C

C

Block

04 21 22

31

31 31

31 31 31 31 31 31 31 31 31 31

32

Detailed

Code

00 00 00

10

11 20

21 22 23 30 31 40 41 42 43 44

10

11

20

21

22

23

30

31

40

41

42

43

44

Symptom/State

Non-standard battery is used. Condensation. Video head is dirty. LOAD direction. Loading does not

complete within specified time UNLOAD direction. Loading does not

complete within specified time T reel side tape slacking when unloading S reel

side tape slacking when unloading T reel fault. S reel fault. FG fault when starting capstan. FG fault during normal capstan operations. FG fault when starting drum. PG fault when starting drum. FG fault during normal drum operations. PG fault during normal drum operations. Phase fault during normal drum operations. LOAD direction loading motor time-

out. UNLOAD direction loading motor

time-out. T reel side tape slacking when

unloading. S reel side tape slacking when

unloading. T reel fault.

S reel fault.

FG fault when starting capstan. FG fault during normal capstan

operations. FG fault when starting drum.

PG fault when starting drum. FG fault during normal drum

operations. PG fault during normal drum

operations. Phase fault during normal drum

operations.

Correction

Use the InfoLITHIUM battery. Remove the cassette, and insert it again after one hour. Clean with the optional cleaning cassette.

Load the tape again, and perform operations from the beginning.

.

Load the tape again, and perform operations from the beginning.

.

Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Remove the battery or power cable, connect, and perform

operations from the beginning. Remove the battery or power cable, connect, and perform

operations from the beginning.

— 10 —

Self-diagnosis Code

Block

Function

Repaired by:

E

61

E

61

E

62

E

62

*1: STEADY SHOT model (CCD-TR818/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E)

Detailed

Code

00

10

00

01

Symptom/State

Difficult to adjust focus (Cannot initialize focus.)

Zoom operations fault (Cannot initialize zoom lens.)

Handshake correction function does not work well. (With pitch angular velocity sensor output stopped.)

Handshake correction function does not work well. (With yaw angular velocity sensor output stopped.)

Inspect the lens block focus reset sensor (Pin qs of CN301 of VC251 board) when focusing is performed when the control dial is rotated in the focus manual mode and the focus motor drive circuit (IC301 of VC-251 board) when the focusing is not performed.

Inspect the lens block zoom reset sensor (Pin qf of CN301 of VC- 251 board) when zooming is performed when the zoom lens is operated and the zoom motor drive circuit (IC301 of VC-251 board) when zooming is not performed.

Inspect pitch angular velocity sensor (SE751 of MI-040/041 board) peripheral circuits. *1

Inspect yaw angular velocity sensor (SE752 of MI-040/041 board) peripheral circuits. *1

Correction

— 11 —

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

SECTION 1

GENERAL

This section is extracted from instruction manual. (CCD-TR V49E/TR V58E/TR V59E/ TRV78E/TRV98E model)

1-1

1-2

1-3

1-4

1-5

1-6

1-7

1-8

1-9

1-10

1-11

1-12

1-13

1-14

1-15

1-16

1-17

1-18

1-19

1-20

1-21

1-22

1-23

1-24E

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

SECTION 2

DISASSEMBLY

The following flow chart shows the disassembly procedure.

2-1. Video light (Video light model)

2-2. LCD section (PD-131 board) (TRV model)

2-3. Front panel section, MI-040/041 board

2-4. Cabinet (L) section

2-5. Cabinet (R) section (CF-077 board) (TR model) 2-6. Cabinet (R) section [Control switch block (CF-1000)] (TRV model)

B/W EVF model

Color EVF model

2-7. VF-129 board (B/W EVF model)

2-8. VF-141, LB-062 boards (Color EVF model/TR818)

PD-131 board service position

MI-040/041 board service position

Mechanism deck service position

Note : Use the parts only which can be removed easily from outside of the mechanism deck.

CF-077, MI-040 boards service position

2-13. Hinge assembly (TRV model)

VF-129, CD-286/281, CF-077, MI-040/041 boards service position

VF-141, LB-062, CD-286, CF-077, MI-040 boards service position

2-9. Battery panel section (Battery terminal board)

2-10. Lens section

2-11. VC-251 board

CCD-TR618/TR618E/TR718E/TR728E/TR818

CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

2-12. Mechanism deck

TR model TRV model Video light model

No video light model B/W EVF model

Color EVF model

:CCD-TR618/TR618E/TR718E/TR728E/TR818 :CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E :CCD-TR618/TR618E/TR718E/TR728E/ TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E :CCD-TR818 :CCD-TR618/TR618E/TR718E/TR728E/ TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E :CCD-TR818

Service position to check the VTR section

Service position to check the Camera section

2-1

[CONNECTION OF EQUIPMENTS]

(TR MODEL)

CPC connector

21

2019

Info lithium battery (L series)

Adjustment remote commander (RM-95)

(TRV MODEL)

Info lithium battery (L series)

Adjustment remote commander (RM-95)

CPC-jig for BX/BK (J-6082-521-A)

CN713

21

2019

Two claws

CPC lid

Two claws

CPC lid

AC power adaptor

AC IN

NOTE: F ollo w the disassembly procedure in the numerical order given.

2-1. VIDEO LIGHT (VIDEO LIGHT MODEL)

1

Push in the dent inside hole with wire tip.

2

Video light

2-2

3

Remove in the direction

of the arrow A.

A

4

Halogen lamp

2-2. LCD SECTION (PD-131 BOARD) (TRV MODEL)

PD-131

CN5502

A

1

T wo tapping

screws (B2 × 5)

6

P cabinet M (12) assembly

5

T wo tapping

screws (B2 × 7)

2

MI screw

(M2 × 4) (H)

4

P cabinet C (12)

3

Five claws

7

Liquid crystal

indicator module

Liquid crystal indicator module

8

Back light Cold cathode fluorescent tube

9

PD-131 board,

Panel frame (12)

PD-131 board

Panel frame (12)

Back light Cold cathode fluorescent tube

Multi CPC jig (J-6082-311-A)

[PD-131 BOARD SERVICE POSITION]

CPC-jig for BX/BK (J-6082-521-A)

Adjustment remote commander (RM-95)

Info lithium battery (L series)

AC IN

AC power adaptor

2-3

2-3. FRONT PANEL SECTION, MI-040/041 BOARD

)

1

Open the jack cover

3

MI screw

(M2

×

4) (H)

2

Two MI screws

(M2

×

4) (H)

4

Two MI screws

(M2

×

4) (H)

FP-263 flexible

×

5)

7

Front panel section

MIBoard

1

Microphone (2P)

5

Claw

6

board (24P)

2

T wo tapping

screws (B2

3

MI-040 board (TR model)

MI-041 board (TRV model)

1

T wo tapping

screws (B2

2

Four claws

4

Microphone

retainer (front)

×

5)

3

Microphone

retainer (rear

5

Microphone

[MI-040/041 BOARD SERVICE POSITION]

FP-263 flexible board (24P)

MI-board

Info lithium battery (L series)

MI-040 board (TR model) MI-041 board (TRV model)

Adjustment remote commander (RM-95)

CPC-jig for BX/BK (J-6082-521-A)

AC power adaptor

TR model

AC IN

CPC-jig for BX/BK (J-6082-521-A)

2-4

2-4. CABINET (L) SECTION

y

6

Two MI screws

(M2

×

4) (H)

5

MI screw

(M2

1

×

4) (H)

7

MI screw

(M2

×

4) (H)

4

MI screw

(M2

3

2

Two MI screws

×

4) (H)

8

Cabinet (L) section

(M2

Cassette lid assembl

×

4) (H)

[MECHANISM DECK SERVICE POSITION]

Note: Use the parts only which can be removed easily from outside of the mechanism deck.

Mechanism deck

AC power adaptor

AC IN

2-5

2-5. CABINET (R) SECTION (CF-077 BOARD) (TR MODEL)

1

MI screw

(M2

×

4) (H)

4

FFC-295 flexible

flat cable (24P)

3

Three MI screws

(M2

2

Liquid crystal display panel,

LCD holder

2

MI screw

(M2

5

Cabinet (R) section

×

4) (H)

×

4) (H)

1

T wo tapping

screws (B2

3

Six tapping

screws (B2

×

5)

C

F

-07

×

5)

[CF-077, MI-040 BOARDS SERVICE POSITION]

Adjustment remote commander (RM-95)

7

4

CF-077 board

AC power adaptor

Info lithium battery (L series)

CPC-jig for BX/BK (J-6082-521-A)

AC IN

FP-263 flexible board (24P)

MI-040 board

MI-040

FFC-295 flexible flat cable (24P)

CF-077

Liquid crystal display panel, LCD holder

CF-077 board

2-6

2-6. CABINET (R) SECTION [ CONTROL SWITCH BLOCK (CF-1000) ] (TRV MODEL)

1

MI screw

(M2

×

4) (H)

4

Claw

2

MI screw

(M2

×

4) (H)

7

Cabinet (R) section

6

FFC-295 flexible

flat cable (24P)

5

Control switch block

(CF-1000)

4

Five tapping

screws (B2

Harness

(PD-110) (20P)

×

5)

3

Three MI screws

(M2

×

4) (H)

1

FFC-295 flexible flat cable (24P)

2

FP-260 flexible board (16P)

3

Push switch (2P)

2-7

2-7. VF-129 BOARD (B/W EVF MODEL)

1

FFC-289 flexible

flat cable (4P)

3

Finder (S) assembly Rotate it in the direction of the arrow in the direction of the arrow

B

and remove it

B

4

C

2

Three tapping

screws (B2

C

.

A

1

screw (T)

2

Slide the button in the

direction of the arrow A.

3

B/W EVF section

×

5)

F lock

2

T wo loose

stopper screws

×

(M2

3)

4

1

T ape (A)

(TRV model)

(TR model)

3

VF base B (10)

PRECAUTION DURING INSTALLATION

8

CRT assembly, VF-129 board,

FFC-289 flexible flat cable

3

Claw

3

Tape (A)

FFC-289 flexible flat cable

4

EVF cabinet

upper B assembly

5

T apping screw

(B2 × 5)

6

EVF tally

VF base B (12)

2

T wo tapping

screws

×

(B2

5)

1

2

T wo tapping

screws (B2

7

EVF cabinet lower B

1

×

5)

VF hinge assembly

REMOVING THE CRT ASSEMBLY AND VF-129 BOARD

2

CRT socket (4P)

6

CRT assembly

5

4

High voltage

cover

1

CRT DT connector (4P)

Anode cable (1P) Do not pull the cable, but remove it in the vertical direction.

3

Remove the high voltage cover with a flat head (–) screwdriver.

High voltage cover

7

VF-129 board

2-8

[VF-129, CD-286/281, CF-077, MI-040/041 BOARDS SERVICE POSITION]

2

Three tapping

screws (B2

×

5)

3

Coror EVF section

2

VF base C (10)

4

Slide fixed plate (10)

4

T ape (A)

Tape (A)

7

A

1

FP-151 flexible

board (20P)

FP-151 flexible board

3

Remove the slide fixed plate (10) by sliding it in the direction of the arrow

A

.

5

Remove the harness retainer from FP-151 flexible board

2

T wo tapping

screws (B2

×

5)

1

2

T wo tapping

screws (B2

×

5)

3

EVF cabinet (rear)

assembly

5

EVF cabinet (upper)

4

Claw

6

EVF cabinet lower C

assembly

7

VF-141, LB-062 board, FP-151 flexible board, VF lens (C) (97) assembly, etc.

1

VF hinge assembly

PRECAUTION DURING INSTALLATION

1

MI screw

(M2

×

4) (H)

6

Two MI screws

(M2

×

4) (H)

TRV model

CD-286 board (TR model) CD-281 board (TRV model)

MI-040 board (TR model) MI-041 board (TRV model)

CPC-jig for BX/BK (J-6082-521-A)

FP-263 flexible board (24P)

MI-board

Adjustment remote commander (RM-95)

FFC-295 flexible flat cable (24P)

AC power adaptor

CF-077

CF-077 board (TR model)

Info lithium battery (L series)

CPC-jig for BX/BK (J-6082-521-A)

AC IN

CRT assembly

VF-129 board

FFC-289 flexible flat cable

Liquid crystal display panel, LCD holder (TR model)

2-8. VF-141, LB-062 BOARDS (COLOR EVF MODEL/TR818)

2-9

[VF-141, LB-062, CD-286, CF-077, MI-040 BOARDS SERVICE POSITION]

)

Info lithium battery (L series)

Adjustment remote commander (RM-95)

CPC-jig for BX/BK (J-6082-521-A)

AC power adaptor

CD-286 board

FP-263 flexible board (24P)

MI-040 board

MI-040

FFC-295 flexible flat cable (24P)

-077

F

C

Liquid crystal display panel, LCD holder

CF-077 board

2-9. BATTERY PANEL SECTION (BATTERY TERMINAL BOARD)

(Remove the Cabinet (L) section reffering to section 2-4 before starting disassembling.)

1

3

FP-262 flexible board

(20P)(TR model)

6

MI screw

(M2 × 4) (H)

T ripod screw

7

Claw

AC IN

VF-141 board

LB-062 board

VF lens (C) (97) assembly

2

MI screw (M2 × 4) (H) (TR model)

8

Battery panel section

4

Battery terminal board (7P)

2

Strap sheet metal

(lower) (12)

(TR model)(TRV model)

2

Strap sheet metal

(lower) (10)

2-10

9

Control switch block

(SS-1000) (5P)

5

MI screw

(M2 × 4) (H)

3

Battery terminal board

1

MI screw

(M2 × 4) (H

2-10.LENS SECTION

e

2

T wo tapping

1

screws (B2

2

×

5)

Lens fram

VC-251

5

Claw

4

T wo screws

(M2

×

lock ace, p2

3),

2-11.VC-251 BOARD

2

Flexible board

(from lens block)(24P)

1

FP-259 flexible board (14P)

3

Screw

(M2

×

lock ace, p2

6

3),

6

Control switch block

(FK-1000) (12P)

3

Lens section

7

VC-251 board

4

FP-257

flexible board

3

T wo screws (M2 × 3), lock ace, p2

2

MD frame B

1

T wo screws (M2 × 3), lock ace, p2

VC-251

5

Screw (M2 × 3), lock ace, p

2-11

[SERVICE POSITION TO CHECK THE VTR SECTION]

Connection to Check the VTR Section

To check the VTR section, set the VTR to the "Forced VTR power ON" mode. Operate the VTR functions using the adjustment remote commander (with the HOLD switch set in the OFF position).

Setting the “Forced VTR Power ON” mode

1) Select page: 0, address: 01, and set data: 01.

2) Select page: D, address: 10, set data: 02, and press the PAUSE button of the adjustment remote commander.

Note: If the machine malfunctions (the operating mode changes by itself), connect the FK-1000 block,

CF-1000 block/CF-077 board.

Control switch block (FK-1000) (12P)

Mechanism deck

FP-257 flexible board

Audio

Monitor TV

Video

A/V out jack

Exiting the “Forced VTR Power ON” mode

1) Select page: 0, address: 01, and set data: 01.

2) Select page: D , address: 10, set data: 00, and press the PAUSE button of the adjustment remote commander.

3) Select page: 0, address: 01, and set data: 00.

When you eject the cassette, connect Pin CN710 on VC-251 board for 1 second.

-251

C

V

VC-251 board

qa

and Pin qs (GND) of

CN710

12

AC power adaptor

Battery terminal board

1

AC IN

(TRV model)

FFC-295 flexible flat cable (24P)

Control switch block (CF-1000)

Info lithium battery (L series)

Adjustment remote commander (RM-95)

CPC-jig for BX/BK (J-6082-521-A)

2-12

FFC-295 flexible flat cable (24P)

(TR model)

CF-077

Liquid crystal display panel, LCD holder

CF-077 board

VC-251

CF-077

Adjustment remote commander (RM-95)

Info lithium battery (L series)

A/V out jack

CPC-jig for BX/BK (J-6082-521-A)

Monitor TV

Video

Audio

FP-257 flexible board

Control switch block (FK-1000) (12P)

When you operate the zoom, connect the FK-1000 block to CN710 of VC-251 board.

Mechanism deck

Battery terminal board

[SERVICE POSITION TO CHECK THE CAMERA SECTION]

AC IN

AC power adaptor

FP-259 flexible board (14P)

Lens block

Flexible board (from lens block) (24P)

VC-251 board

CF-077 board

FFC-295 flexible flat cable (24P)

Control switch block (CF-1000)

FFC-295 flexible flat cable (24P)

Liquid crystal display panel, LCD holder

(TR model)

(TRV model)

Connection to Check the Camera Section

To check the camera section, set the camera to the "Forced camera power ON" mode.

Setting the “Forced Camera Power ON” mode

1) Select page: 0, address: 01, and set data: 01.

2) Select page: D , address: 10, set data: 01, and press the PAUSE button of the adjustment remote commander.

Note: If the machine malfunctions (the operating mode changes by itself), connect the FK-1000 block,

CF-1000 block/CF-077 board.

Exiting the “Forced Camera Power ON” mode

1) Select page: 0, address: 01, and set data: 01.

2) Select page: D, address: 10, set data: 00, and press the PAUSE button of the adjustment remote commander.

3) Select page: 0, address: 01, and set data: 00.

2-13

2-12.MECHANISM DECK

s

4

Control switch block

(FK-1000)

1

3

Screw (M2 × 3), lock ace, p2

2

Two claws

2

MD frame A

1

(M2 × 3), lock ace, p2

Three screw

C

B

A

3

Mechanism deck

2

Slide it in the direction of the arrow A and disengage the claws Remove the LS lid assembly in the direction of the arrow C.

B

1

Claw

B

2-13.HINGE ASSEMBLY (TRV MODEL)

(Remove the LCD unit reffering to section 2-2 before starting disassembling.)

5

Four tapping

screws (B2 × 5)

A

6

7

Control switch block

(PR-10000)

3

Hinge cover M

5

Harness (PD-110)

1

FP-260 flexible

board (16P)

A

3

Three tapping

screws (B2 × 5)

4

Hinge blind,

Push switch

2

Push switch (2P)

2-14

6

Screw

(M1.7 × 2.5)

8

Hinge assembly

4

Harness clamp

1

Four claws

2

Hinge cover C

)

2-14.CIRCUIT BOARDS LOCATION

CD-286 (TR model) CD-281 (TRV model) (CCD IMAGER)

MI-040 (TR model) MI-041 (TRV model) (STEADY SHOT, MIC AMP, IR DRIVE)

CONTROL SWITCH BLOCK (CF-1000) (TRV model)

PD-131 (TRV model) RGB, TIMING GENERA T OR, BACK LIGHT

VC-251 CAMERA PROCESSOR, Y/C PROCESSOR, FOCUS/ZOOM MOTOR DRIVE, REC PB AMP, LINE I/O AMP, SERVO, MODE CONTROL, HI CONTROL, AUDIO, DC/DC CONVERTER

VF-129 (B/W EVF model) (B/W EVF)

LB-062 (TR818) (EVF BACK LIGHT)

VF-141 (TR818 (COLOR EVF)

CF-077 (TR model) (SWITCH)

2-15

)

2-15.FLEXIBLE BOARDS LOCATION

The flexible boards contained in the mechanism deck are not shown.

CONTROL SWITCH BLOCK (FK-1000)

FFC-289 (B/W EVF model) (USED B/W EVF)

FP-259

FFC-295

FP-263

CONTROL SWITCH BLOCK (PR-10000) (TRV model)

CONTROL SWITCH BLOCK (SS-1000)

FP-257

FP-260

LIQUID CRYSTAL DISPLAY PANEL (TR model)

FP-151 (TR818) (USED COLOR EVF)

IRIS FLEXIBLE ASSEMBLY 630

FP-262 (TR model

2-16E

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

SECTION 3

BLOCK DIAGRAMS

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

3-1

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

3-1. OVERALL BLOCK DIAGRAM (1/2)

(STEADY SHOT MODEL)

YAW AD

PITCH AD

(TR MODEL)

(LASER LINK MODEL)

D3901,3902

(TR MODEL)

S-Y I/O S-C I/O

AUDIO I/O

A 4.75V

IC3901

IR

TRANSMITTER

(4-13)

IR V IR L,R

(4-47)

IC301

MIC901

MIC

A/V OUT

RFU DC OUT

MI-041

(TRV MODEL)

BOARD(2/2)

SE751

YAW

SENSOR

SE752 PITCH

SENSOR

(4-11)

IC753

SENSOR

AMP

FP-257(1/2)(FLEXIBLE)

J201

S VIDEO OUT

J202

MI-040 BOARD(1/2)

(4-12)

IC752

MIC

AMP

MI-040 BOARD(2/2)

( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.

M905

FOCUS MOTOR

M M

FOCUS MOTOR DRIVE

ZOOM

FOCUS

SENSOR

LENS

ZOOM MOTOR

ZOOM

MOTOR

DRIVE

M906

ZOOM

SENSOR

S-Y I/O S-C I/O

VIDEO I/O

IR VIDEO

AUDIO I/O IR L IR R MIC

HP

SP+,-

METER

HALL

H

HALL(-)

IC221

VIDEO

OUTPUT

VC SO,VC SI,VC SCK

IRIS

DRIVE(-)

AFM

AUDIO

PROCESS

HEAD PHONE

AMP

SPEAKER

AMP

IC351

CD-286 BOARD CD-281 BOARD

(TR MODEL) (TRV MODEL)

IC191

CCD

IMAGER

NIGHT SHOT

PLA/GLASS

(4-48)

IC302

YAW AD,PITCH AD

Y

C

REC AFM PB RF

BEEP

IRIS PWM

MALL AD

ZM RST SENS FC RST SENS

DRIVE

HALL AMP

(4-52)

AMP

Y C

(4-60)

(4-43)

CCD OUT

V1-V4 VSHT

H1,H2,RG

CCD OUT

VC-251 BOARD

(4-43)

IC271

TIMING

GENERATOR

VC SO,VC SI,VC SCK

DIR0 A,B DIR1 A,B

(4-43)

IC272

Y

S/H

A/D

CONV.

Y C EVF Y EVF R EVF G EVF B

PANEL R PANEL G PANEL B

10

C

GCA

PB C

CAM DD ON

(4-45)

IC151

CAMERA Y/C PROCESS.

VTR Y/C PROCESS.

ATF.

FOCUS/ZOOM MOTOR CONTROL

PB Y

COLOR1

COLOR4

PB ATF

PB C

IC153

CHARACTER GENERATOR

ADJUST

VOLTAGE

VC SO,VC SI,VC SCK

(4-46)

OSD SO OSD SCK

D/A CONVERTER

(EVR)

(4-60)

IC601

REC Y C(+REC ATF)

REC AFM

PB RF

(4-50)

IC101

REC/PB

AMP

SWP

FLYING ERASE

OSC

OH SO,XCH SCK

OSD SO,OSD SCK

IRIS PWM,HALL AD,ZOOM RST SENS, FC RST SENS,YAW AD,PITCH AD, PLA/GLASS

VC SO,VC SC,VC SCK

FLYING ERASE

SP1

SP2

FE

CH SP1

CH SP2

B MECHA DECK

(SEE PAGE 4-53)

(4-11)

IC751

MI-041

(TRV MODEL)

BOARD(1/2)

SP901

SPEAKER

J001

(HEADPHONES)

REMOTE

XSIRCS SIG

COMMANDER

RECEIVER

(REMOTE COMMANDER MODEL)

D3903

(EXCEPT LASER LINK MODEL)

CONTROL SWITCH BLOCK(CF-1000)(1/2)

(SEE PAGE 4-33)

SP+,-

HP

16

IR ON

TRV MODEL : CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

TR MODEL : CCD-TR618/TR618E/TR718E/TR728E/TR818

REMOTE COMMANDER MODEL : CCD-TR728E/TRV49/TRV49E/TRV59E/TRV78/TRV78E/TRV98/TRV98E

LASER LINK MODEL : CCD-TRV98

STEADY SHOT MODEL : CCD-TR818/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

B/W EVF MODEL : CCD-TR618/TR618E/TR718E/TR728E/TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

COLOR EVF MODEL : CCD-TR818

3-3 3-4

VF-129 BOARD

H OUT

EVF Y

CRT DRIVE

IC901

T901,902

DV1,DV2

(4-25)

(B/W EVF MODEL)

DY

H

DH1,DH2

HV

G2

H

G1

V

VF-141 BOARD

(4-30)

IC4501

V901

R G

CRT

B

LB-062 BOARD

EVF BL 4.75V

(4-32)

LCD

DRIVE

TIMING

GENERATOR

IC4502

DC/DC CONVERTER BACK LIGHT

DRIVE

IC4601

VR VG VB

(4-30)

(COLOR EVF MODEL)

LCD903

LCD

PANEL

(BACKLIGHT)

ND4601

PD-131 BOARD(1/2)

R G

DRIVE

B

TIMING

GENERATOR

IC5502

(4-21)

CONVERTER BACK LIGHT

IC5601,5602

BL REG

LCD

DC/DC

DRIVE

(4-20)

IC5501

VR VG VB

(4-20)

(TRV MODEL)

LCD901

LCD

PANEL

ND901

(BACKLIGHT)

IR ON, XSIRCS SIG SIRCS PWM

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

3-2. OVERALL BLOCK DIAGRAM (2/2)

FP-257

M

SWITCH

SENSOR

MODE

S901

DEW

(FLEXIBLE)(2/2)

VIDEO LIGHT DRIVE

VL UNREG

V LIGHT PWM

LOAD,UN LOAD

MSW A-C

DEW AD

VC-251 BOARD

VIDEO LIGHT

(VIDEO LIGHT MODEL)

CH SO,XCH SCK

OSD SO,OSD SCK

IRIS PWM,HALL AD,ZOOM RST SENS, FC RST SENS,YAW AD,PITCH AD PLA/GLASS

VC SO,VC SC,VC SCK VC SO,VC SI,VC SCK

B MECHA DECK

(SEE PAGE 4-53)

FP-220

(FLEXIBLE)

FP-249(FP-355,356)

D001

T/E LED

LOADING MOTOR

(FLEXIBLE)

Q001

Q002

M903

TAPE TOP SENSOR

H001

T REEL

FG SENSOR

H002

S REEL

FG SENSOR

TAPE END SENSOR

( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.

TRV MODEL : CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

TR MODEL : CCD-TR618/TR618E/TR718E/TR728E/TR818

VIDEO LIGHT MODEL : CCD-TR618/TR618E/TR718E/TR728E/TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

COLOR EVF MODEL : CCD-TR818

(4-58)

IC503

MODE

CONTROL

BACKUP VCC X RESET

KEY AD2,3,4

DIAL A,B

BEEP

XS/S SW

XCAM+STBY SW XVTR MODE SW

XEJECT SW

KEY AD0,1

TAPE TOP

T REEL(+),(-)

S REEL(+),(-)

TAPE END

(4-54)

IC451

LOADING MOTOR

DRIVE

(4-54)

IC451

TAPE TOP

DETECT

T REEL FG

AMP

S REEL FG

AMP

TAPE END

DETECT

OSD SO

OSD SCK

(4-56)

EEPROM

IC401

DEW AD

(4-56)

IC402

MSW A-C

V.LIGHT PWM

TAPE TOP

T REEL FG

S REEL FG

TAPE END

MECHA/CAMERA

CONTROL/SERVO

MECHA/ CAMERA

CONTROL

HI SO,HI SI,HI SCK

CAMERA,VIDEO, AUDIO,SERVO CONTROL SIG

(2/5)

(3/5)

IRIS PWM HALL AD ZM RST SENS FC RST SENS YAW AD PITCH AD PLA/GLASS

LOAD,UN LOAD

XCC DOWN

(4-57)

IC502

INITIAL RESET

BACKUP VCC

OSD SO,OSD SCK

LI 3V

VTR UNREG

ZOOM AD

CF-077 BOARD

CONTROL SWITCH BLOCK (CF-1000)(2/2)

(TR MODEL)

(4-38)

IC001

LCD

INDICATOR

DRIVE

BT001

LITHIUM

BATTERY

S002-S011 FUNCTION

SW

S006

SEL/PUSH

EXEC DIAL

BZ001

BUZZER

(TR MODEL)

CONTROL SWITCH BLOCK(SS-1000)

(SEE PAGE 4-58)

START/STOP SW

POWER SW

CONTROL SWITCH BLOCK(FK-1000)

(SEE PAGE 4-58)

EJECT SW

VTR FUNCTION SW

ZOOM SW

(TRV MODEL)

INDICATOR

(TRV MODE)

OPEN/CLOSE

PANEL

LCD

SW

16

FP-38

IR ON, XSIRCS SIG SIRCS PWM

(FLEXIBLE)

CAPSTAN

FG

CFG(+),(-)

(4-54)

(1/2)

LED

DRIVE

IC451

WAVE SHAPER

CAP ERROR

REC PROOF SW

CC DOWN SW

(4/5)

(4-54)

IC451

(5/5)

DRUM PWM

LPF

CAP PWM

TAPE LED(K) TAPE LED ON

REC PROOF

D PG,D FG D PG,D FG D PG,D FG

M901

DRUM MOTOR

DRUM

M

PG FG

M902

CAPSTAN MOTOR

M

DRIVE

WAVE SHAPER

ME/MP HI8 MP

S001

S002

CC DOWN

(4-54)

IC451

(1/5)

DRUM VS DRUM ERROR

DRUM MOTOR

DRIVE

CAP VS

(4-61)

IC001

DRUM PWM

DRIVE

CAPSTAN PWM

DRIVE

IC001

ME/MP SW HI8 MP SW

CAP FG

SERVO

ZOOM AD

PD-131 BOARD(2/2)

KEY AD5

CONTROL SWITCH BLOCK (PR-10000)

S001

PANEL

REVERSE SW

(SEE PAGE 4-19)

(TRV MODEL)

BEEP

XSIRCS SIG

SWP

FAST CHARGE

DC PACK SW

CAM DD ON

VTR DD ON

CAM DD ON

BATT SIG BATT/EXT

IR ON

BATT UNREG

VL UNREG

VTR UNREG

MT 4.75V

D 2.8V A 2.8V

AU 2.8V

D 1.5V

CAM -7.0V

CAM 15V AU 4.75V

A 4.75V

RP 4.75V

EVF BL/BW EVF 4.75V

EVF 2.8V

EVF 13.3V

(COLOR EVF MODEL)

F001

(VIDEO LIGHT MODEL)

(4-61)

IC001

DC/DC

CONVERTER

DRUM/

CAPSTAN

PWM

DRIVE

Q002

BATT(+) DC PACK SW BATT SIG BATT(-)

(TRV MODEL)

BATT/EXT

ACV UNREG ACV GND

F002

(2/2)

F003

F004

BT901

PANEL 2.8V PANEL 4.75V

PANEL 13.3V PANEL -15.3V BL REG

BATTERY

TERMINAL

DC IN

TO PD-131 BOARD

(SEE PAGE 3-19)

(TRV MODEL)

3-5 3-6

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

3-3. CAMERA/VIDEO BLOCK DIAGRAM (1/2)

IC191 7 

IC191 3,4 

IC191 1,2

(TR MODEL)

CD-286 BOARD

H

0.6Vp-p

6.8Vp-p

H

6.8Vp-p

H

IC191 qs“ 



105 nsec

FP-257(FLEXIBLE)

S VIDEO

A/V OUT

IC191

CCD IMAGER

CCD OUT

OUT

V1 V2 V3 V4

RG

H2 H1

VL

SHT

VDD

4.6Vp-p

(TRV MODEL)

CD-281 BOARD

(4-8)

7

4 3 2 1

12

14 13 11 10

8

Q191

IC191 qd,qf¢

IC271 wa REC

J201

Y

1

34

2

C

CN191

105 nsec

AUDIO I/O L

1

11 12 13 14

9

7 8 5 4 3

8.717 MHz

CCD OUT

V1

V2

V3 V4

RG

H2 H1

CAM-7.0V

VSHT

CAM 15V

6.8Vp-p

6.0Vp-p

S-Y I/O

S-C I/O

XS JACK IN

VIDEO I/O

V JACK IN

CN271

14

4 3 2 1 6

8

7 10 11

12

13

15

16

10

7

( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.

IC271 qa REC/PB

10 43 13

33

25 26 28 31

27

29

30

19

20

22 21 18

42

R2.4Vp-p P2.1Vp-p

IC272 eh PB

14.3181 MHz

(4-43)

IC271

TIMING GENERATOR

VDD1 VDD6 VDD2

CLPDM

XSHP XSHD

VSHT

PBLK

V2 V1

XSG1

V3 V4

VH

VGAT

SYSCK

VL

VICK

CHCK

VM

OSC 0

VDD3

OSC 1

VDD4

AHD AVD SSK

H2 H1

SEN

RG

RST

SSO

DSGAT

IC221 qk  REC/PB (S-Y OUT)

PB C RF

0.3Vp-p

H

3.6Vp-p

1 15 16

2

34 48

ID

41

XV1

V STOP

36 11 12

9

7

CK

5

4

44 45 37 38

SSI

39 40

35

47 46

H

Y

18

V

22

C

14

MCK

ADCK

X271

28.375MHz(PAL)

28.636363MHz(NTSC)

XCS KINUTA

XRST KINUTA

CK CONT1 CK CONT2

2Vp-p

CL

(4-52)

IC221

VIDEO OUT

YX

+

XVC SCK VC SO

VC SI

IC221 rf REC/PB

DDS

PBLK

19

CLPDM

23

30

34

36

XSHP

21

XSHD

22

IC271 5 REC/PB

28.63562 MHz

CLP

LINE

PB

CLP

TIMING

ADCLK

16 13 43 45

ADCK

3.6Vp-p

H

Y IN3

LPF

C IN3

BPF

VC-251 BOARD

IC271 wh REC

IC271 wk

V1

REC

V2 V3 V4 RG

H2 H1

Y I/O

C I/O

CN

6.8Vp-p

H

6.8Vp-p

H

D 2.8V

CAM-7.0V

CAM 15V

CAM-7.0V

(1/6 CCD MODEL)

A 4.75V

D 2.8V

(1/4 CCD MODEL)

H2 H1 RG

CAM DD ON

IC221 ws» REC/PB

H

IC221 qfƒ REC/PB(S-C OUT)

S/H,AGC,A/D CONVERTER

CDS/ PXGA

CAM LINE

AVDD

24 27 33 40 17,18

A 2.8V A 2.8V 2.8V

R0.52Vp-p P0.48Vp-p

44

5

IC272

IC272 qh REC/PB

14.318 MHz

(4-43)

AGC

DVDD

A/D

D-AGC

CONV.

CTL

DRVDD HDRST SYS V

3.2Vp-p

D9

ı

D0

CLPOB

XRST KINUTA

SYS V

11

20

48 47 46

ı 2

AD1-AD10

XCH SCK

CH SO XCS CH

IC272 e; REC

PB C RF

1.2Vp-p

H

CLP1

MCK CL ADCK

XSG1 XV1 ID PBLK V STOP

AHD AVD

KINUTA C OUT

KINUTA Y OUT

CAMERA/VIDEO(2)

(SEE PAGE 3-9)

2Vp-p

H

0.52Vp-p

H

IR VIDEO

V

24

C VCC

A 4.75V

D VCC

D 2.8V

Y VCC

V VCC

23 16 15 8

A 4.75V

XSCK

11

XCS

10

SI

(FOR CHECK)

TRV MODEL : CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/

TRV88/TRV98/TRV98E

TR MODEL : CCD-TR618/TR618E/TR718E/TR728E/TR818

1/6 CCD MODEL : CCD-TR618/TR618E/TR718E/TR728E/TRV49/TRV49E/TRV58/TRV58E

CN713

14

IR VIDEO

IC221 wfƒ  REC/PB IR ON

1/4 CCD MODEL : CCD-TR818/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

NTSC MODEL : CCD-TR618/TR818/TRV49/TRV58/TRV68/TRV78/TRV88/TRV98

PAL MODEL : CCD-TR618E/TR718E/TR728E/TRV49E/TRV58E/TRV59E/TRV78E/TRV98E

16

3-7 3-8

9

IC221 5 REC/PB

H

XVC SCK

VC SO

R0.4Vp-p P0.5Vp-p

XCS I/O

XCH SCK CH SO XCS CH

SYS V XRST KINUTA XCS KINUTA CK CONT1 CK CONT2 XCS IO

XVC SCK VC SO VC SI

V JACK IN XS JACK IN CAM DD ON

IR VIDEO

(IC402 )

81 82

(IC402 )

83

(IC402 )

108

(IC402 )

18

(IC402 )

19

(IC402 )

104

(IC402 )

110

(IC402 )

16

(IC402 )

78

(IC402 )

79

(IC402 )

80

(IC402 )

(IC503 )

84 85

(IC503 )

28

(IC503 )

(CN703 )

4

VTR/CAMERA CONTROL

(SEE PAGE

3-11)

MODE CONTROL

(SEE PAGE

3-16)

AUDIO

(SEE PAGE

3-18)

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

3-4. CAMERA/VIDEO BLOCK DIAGRAM (2/2)

VC-251 BOARD

PB C RF

AD1 - AD10

CLP1

IC151 ia REC/PB

VTR/CAMERA

(SEE PAGE 3-9)

H

BUFFER

IC151 qf REC/PB

CONTROL

Q158

3.2Vp-p

CL MCK

V STOP

Q151

VCO

FSC

0.4Vp-p

H

IC151 wj REC(COLOR EVF MODEL)



IC151 ej REC (COLOR EVF MODEL)

H

IC151 4 REC/PB

4.8Vp-p

H

4.8Vp-p

(COLOR EVF MODEL)

COLOR EVF

(VF-141)

(SEE PAGE 3-23)

(B/W EVF MODEL)

B/W EVF

(VF-129)

(SEE PAGE 3-21)

(TRV MODEL)

LCD

(PD-131)

(SEE PAGE 3-19)

0.42Vp-p

EVF R EVF G

EVF B EVF XHD EVF XVD

PANEL R

PANEL G

PANEL B

PANEL XVD

PANEL SYNC

CAMERA/VIDEO(1)

(SEE PAGE 3-8)

3 4 5

PANEL XHD

7

PANEL XVD

8

CN708

3

EVF Y

CN715

3

4

5

8

7

CN701

16

TRV MODEL : CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/

B/W EVF MODEL : CCD-TR618/TR618E/TR718E/TR728E/TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

COLOR EVF MODEL : CCD-TR818

MCK CL ADCK

XSG1 XV1 ID PBLK V STOP

AHD AVD

AFC FO(IC402)

AFC FO ADJ(IC601)

IC151 <xzc REC/PB

KINUTA C OUT

KINUTA Y OUT

Q156

BUFFER

Q153

BUFFER

TRV88/TRV98/TRV98E

14.318 MHz

() : Page No. shown in ( ) indicates the page to refer on the schematic diagram.

AD IN 9

187

ı

AD IN 0

196

183

CLP1

ADCK

185

164

VCK

81

MCK

166

XSG1

168

XV1

171 172

PBLK

167

VGAT

AHD

169

AVD

170

53

AMPO

67

OSCI

79

OFSC

148

ENO

149

DIR0B

150

DIROA

151

DIR1A

152

DIR1B

153

EN1

159

IRIS COM

161

FC RST

162

ZM RST

C OUT

213

Y OUT

4

27 34 37 14 17 24

75

PANEL HD

74

PANEL VD

76

PANEL SYNC

IC151 wf REC/PB

H

4.8Vp-p

CAMERA Y/C PROCESS

VTR Y/C PROCESS,ATF,FOCUS/ZOOM MOTOR CONTROL

ID

CAM

SG

FOCUS/

ZOOM

MOTOR

CONTROL

D/A

RGB ENCODER D/A CONV

95 96 97 98 99

4.8Vp-p

XSCKSOSI

(4-45)

IC151

CAMERA

PROCESS

VTR Y/C

PROCESS

XCS

XCS KINUTA

REC Y

D/A

REC C

REC RF

+

D/A

A/D

XSG V RST

AFT SAMPLE

MECHA FLD

MECHA HD MECHA VD

XTBC V RST

IC151 qj REC/PB

H

Y RF IN

DOP IN

ATF IN

VI HDO

VI VDO

TBC VD

CGCK

OSD L ON

OSD R ON

COLOR4

OSD P ON

COLOR3 COLOR2 COLOR1

JOG VD 1/2 SWP SWP DIR

SYS V

CK CONT2

CK CONT1

4.8Vp-p

7

51

77

49

146 144

158

179 182 181 177 180 176 175 174

83 84 85 86 87 88 89 93

94 100 157 101

D/A

A/D

Y/C

REC ATF

PB ATF

ATF

PB C IN

XRST

XRST KINUTA

IC151 7 REC/PB

7

DOP(IC101 )

PB ATF+C

IC151 ef REC(B/W EVF MODEL)

H

IC151 ef REC(COLOR EVF MODEL)

H

50 nsec/div

IC151 ta PB

IC151 rl PB

0.88Vp-p

4.8Vp-p

IC151 ig REC/PB

0.4Vp-p

50 nsec/div



H

20

XHSYNC

19

XVSYNC

8

OSC

11

BLKC

13

BLKB

14

VC3

15

BLKA

16

VC2

17

VC1

18

VC0

MODE CONTROL

(SEE PAGE 3-16)

25 Hz

0.4Vp-p

IC153

CHARACTER GENERATOR

2.8Vp-p

(4-46)

CLK

XCS DATA XPCL

(IC503 )

(IC503 ) (IC503 ) (IC503 )

1 2 3 4

(IC601)

9

45 44 46

REC RF(Y+C+AFT)

RF AGC OUT

RF AGC CONT

PB C RF

XOSD SCK

XCS OSD

OSD SO

XSYS RST

OSD SO

XCS OSD

XOSD SCK

VI VDO

TBC VD

RF AGC OFF

IC101 qf PB

(IC402)

50 nsec/div

Q105,106

SW

AGC SLOW

0.4Vp-p

5V

3V

13

A 2.8V

IC101 1 REC

(4-60)

IC601

D/A CONVERTER

(EVR)

REC L CONT

REC Y/MT CONT

DOC DET

RF AGC CONT

AFC FO ADJ FREQ TUNE

CFG DUTY

HALL REF

HALL GAIN

HALL OFFSET

IR A DEV IR CARR IR V DEV

1.5M DEV AU BPF

1.7M DEV

XVC SCK

DA STB

1 2

A 4.75V

5 µsec

MT FO

RP IR

A FADE

VC SO

IC101 wj,ef REC

47 47

108

48

9 19 18

78 79 80

46 49

104 107 118 113 112 111

VTR/CAMERA CONTROL

45

110

21 44 85

114

56

54 55 59



50 nsec/div

XFE ON

CN101 qh, Q101 C REC

138 nsec

AUDIO

(SEE PAGE 3-16)

AUDIO

(SEE PAGE 3-15)

SERVO

(SEE PAGE 3-12)

(SEE PAGE 3-11)

Q101-104

FLYING ERASE

OSC

3.0Vp-p

7.6Vp-p

PB RF

REC RF

RF SWP

CN101

10

12

16

9 15 16

CN713

(FOR CHECK)

VIDEO HEAD

CH SP1

CH SP2

FLYING ERASE

(4-50)

IC101

REC/PB AMP

Y/C/ATF IN

6

PB Y

AGC TC

RF AGC IN

5 4 3

26 25 24 23 22

8

20

19 18 17 7 6 21

9 10 11 12

27 28 15

16

AGC

LPF

14 1 4116 8 1248 15 19

PB RF

REC AFM

0.4Vp-p

9

10

18

11

MT Q

SWP

GCA,

MIX AMP

(IC902)BOTH REC

(IC902)RP PB MODE

22 23

DOP

SW

(IC151 )

REC L CONT

79

AFC FO (Q203)

(IC601)

RP IR

REC AMP

PB

AMP

DOC DET

346 47 713

MTQ

MT FO

REC Y/MT CONT

IR V DEV IR CARR IR A DEV

FSC

REC AFM PB RF

1.5M DEV

1.7M DEV AU BPF A FADE

CFG DUTY

VC RF SWP SWP DIR SYS V

1/2 RF SWP RF AGC XCS KINUTA

XRST KINUTA

XVC SCK VC SO VC SI

RP PB MODE XFE ON

CK CONT1 XTBC V RESET MECHA VD TBC VD MECHA HD MECHA FLD XSG V RST CK CONT2 DA STB ATF SAMPLE AFC FO

HALL GAIN HALL REF HALL OFFSET

DOP VIVDO

MT SW

AGC SLOW BOTH REC JOG VD

27

34

38 39

28

33

(IC402 ) (IC402 ) (IC402 ) (IC402 )

(IC402 ) (IC402 )

(IC402 )

(IC402 ) (IC402 ) (IC402 )

(IC402 ) (IC402 )

(IC402 ) (IC402 ) (IC402 ) (IC402 ) (IC402 ) (IC402 ) (IC402 ) (IC402 ) (IC402 ) (IC402 ) (IC402 )

(IC402 )

(IC402 ) (IC402 ) (IC402 )

3-9 3-10

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

3-5. VTR/CAMERA CONTROL BLOCK DIAGRAM

(STEADY SHOT MODEL)

(TR MODEL) (TRV MODEL)

MI-040 BOARD MI-041 BOARD

(4-11)

IC753

LPF

(4-48)

19

5

17

7

2

23

4

21

OUT 3B OUT 3A OUT 4B OUT 4A

OUT 1A OUT 1B OUT 2A OUT 2B

PITCH/YAW SENSOR AMP

8 2

LIA1

4

VREF1

12

LIA2

16

(1/4)

9

10

(2/4)

3 2

12 13

(4/4)

(4-47)

IC301

ZOOM

MOTOR

DRIVE

FOCUS MOTOR

DRIVE

VM1 VM23 VM4 VDD

1 20 8 24

OUT1

CRST

OUT2

VCCVREF2

5 6

HALL GAIN HALL OFFSET HALL REF

EN4

IN4

EN3

IN3

EN2

IN2

EN1

IN1

19

18

20

(4-48)

IC302

HALL AMP

16 15 14 13

12 11 10

9

D 2.8V MT 4.75V

CN753

18 18

17 17

19 19

14 14

LPF

(3/4)

7

M904

IRIS

METER

M

H

ZOOM LENS

UNIT

NIGHT SHOT

ZOOM

SENSOR

FOCUS

SENSOR

M906

ZOOM

MOTOR

M

M905

FOCUS

MOTOR

M

SE751

4

PITCH

2

SENSOR

1

SE752

4

YAW

2

SENSOR

1

D 2.8V

IC302

IRIS DRIVE

8

IC302

HALL BIAS CONTROL

1

14

IC302

HALL GAIN CONTROL

TEMP COM

TEMP OUT

DRIVE(+)

DRIVE(-)

NIGHT SHOT

CONT(+)

BIAS(+)

HALL(-)

HALL(+)

BIAS(-)

FC SENSE

SENSE VCC

ZM SENSE

FC SENSE

ZM XA

ZM A

ZM XB

ZM B

FC XA

FC XB

CN301 15 16

24

23 21 22

17

20

18 19

GND

13

VCC

11

ZM

9

OUT

14

OUT

12

10

5 8 6 7

FC A

4 1

FC B

3 2

16

Q302(1/2)

Q303

Q302(2/2)

D 2.8V

Q301

DRIVE

ZM RST SENS

FC RST LED

ZM RST LED

FC RST SENS

PLA/GLASS

TRV MODEL : CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

TR MODEL : CCD-TR618/TR618E/TR718E/TR728E/TR818

VIDEO LIGHT MODEL : CCD-TR618/TR618E/TR718E/TR728E/TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

STEADY SHOT MODEL : CCD-TR818/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

COLOR EVF MODEL : CCD-TR818

( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.

VC-251 BOARD

XCH SCK

CH SO

PITCH AD

VST C RESET

YAW AD

A 2.8V

CN703

LENS TEMP AD

IRIS PWM

LENS FILTER ON SW

HALL AD

(IC151 (IC151

(IC151

159 18HALL GAIN (IC601 ) 17HALL OFFSET (IC601 ) 19HALL REF (IC601 )

162ZM RST )(IC151 161

153 152DIR1B )(IC151

151DIR1A )(IC151

148 149

150

IRIS COM (IC151 )

FC RST )(IC151

EN1 )(IC151

EN0 DIR0B

DIR0A

CAMERA/VIDEO(2)

(SEE PAGE 3-9,10)

) )

)

CAMERA/VIDEO(1)

(SEE PAGE 3-8)

MODE CONTROL

(SEE PAGE 3-16)

AUDIO

(SEE PAGE 3-18)

CAMERA/VIDEO(2)

(SEE PAGE 3-10)

XCS CH

SYS V

XRST KINUTA

XCS KINUTA

CK CONT1 CK CONT2

XCS IO

VC SI

VC SO

VC SCK

XCC DOWN

DEW AD

ZOOM VR AD

XSYS RST

XCS VC

HI SO

HI SI

XHI SCK

SYS V

VC RF SWP

XCS AU

VC SI

VC SO

VC SCK

VC SI

VC SO

XVC SCK

XCS KINUTA

SYS V

VC RF SWP

JOG VD

RF AGC OFF

MT SW

BOTH REC

RP PB MODE

XFE ON

X1/2 SWP

XTBC V RESET

XRST KINUTA

MECHA VD

TBC VD

MECHA HD

MECHA FLD

CK CONT2

XSG V RST

DA STB

VICDO

AFC FO

ATF SAMPLE

AGC SLOW

D 2.8V

DOP

4

DODIXCS 3 2

XSCK 8

VCC

IC401

D 2.8V

X401

20MHz

VST C RESET

VIVDO

RST

EEPROM

1627

(4-56)

25

VDD

64

VDD

100

AVDD

101

AVRH

120

VDD

1

XTAL

2

EXTAL

81

XCH SCK

82

CH SO

83

XCS CH

7

XRST VC

77

XCS VC

76

HI SO

75

HI SI

74

HI SCK

108

SYSV

43

LENS FILTER ON SW

22

ZM RST LED

53

FC RST LED

58

VST C CHARGE

23

ZM RST SENS

98

YAW AD

97

PITCH AD

70

IRIS PWM

86

LENS TEMP AD

84

HALL AD

24

FC RST SENS

94

PLA/GLASS

19

XCS KINUTA

20

XCS AU

80

VC SI

79

VC SO

78

XVC SCK

55

BOTH REC

104

CK CONT1

110

CK CONT2

46

RP PB MODE

49

XFE ON

48

X1/2 SWP

47

SWP

107

XTBC RESET

18

XRST KINUTA

16

XCS IO

118

MECHA VD

113

TBC VD

112

MECHA HD

111

MECHA FLD

114

MEM VD

45

XSG V RST

56

MT SW

21

DA STB

9

RF AGC OFF

XCS EEPROM

26

XWE EEPROM

(4-56)

IC402

VTR/CAMERA CONTROL

(1/2)

UN LOAD

LOAD

LM LIM CONT

XLM LIM ON

M SW C M SW B M SW A

TAPE TOP TAPE END

S REEL FG AD

T REEL FG AD

TAPE LED ON

XREEL HALL ON

ME SW HI8 MP SW REC PROOF

V LIGHT PWM

ATF SAMPLE

AFC FO

AGC SLOW

ZOOM SW AD

XCS EVF D/A

EVF DO ON

JOG VD

LCD HOLD

XCS LCD DA

B MECHA DECK

(SEE PAGE 4-53)

(4-54)

IC451

MT 4.75V

D 2.8V

WAVE

SHAPER

WAVE

SHAPER

LED

DRIVE

TOP IN END IN

Q451

OUT1

OUT2

(1/6)

M903

MODE SWITCH

Q001

TAPE TOP

SENSOR

Q002

TAPE END

SENSOR

H

LOADING

MOTOR

M

S901

DEW

SENSOR

H002

S REEL

SENSOR

H

H001

T REEL

SENSOR

S001

S002

CC DOWN SW

D001

TAPE LED

CN704

53

51

CN707

CN712 45 46

35 36

39 38

CN702

LM(+)

8 7

6 5

4 3 2

12

TAPE TOP(C)

2

TAPE END(C)

8

TAPE LED(A)

9

SENSOR VCC

13

S REEL(-)

4

S REEL(+)

5

T REEL(-)

11

T REEL(+)

12

HALL COM

10

TAPE LED(K)

14

6 3

REC PROOF

7

C LOCK SW

15

19 20

LM(-)

M SW(C) M SW(B) M SW(A)

DEW(+)

ME/MP HI8 MP

7 8

5 6

4 3 2

12

2

8

9

13

4 5

11 12 10

14

6 3 7

15

VIDEO LIGHT

FP-257(FLEXIBLE)

(VIDEO LIGHT MODEL)

CN708

11 13 12

CN701

6 10

9 11

POWEREVF DO ON

XCS EVF D/A VC SO XCS SCK

PANEL HOLD XCS LCD DA

VC SO XVC SCK

COLOR EVF (VF-141)

(SEE PAGE 3-23)

(COLOR EVF MODEL)

LCD

(PD-131)

(SEE PAGE 3-19)

(TRV MODEL)

LOADING MOTOR DRIVE

VTR UNREG

33 32 29 30

37 36 35

D 2.8V

DEW AD

42

9 56 55 50 49

VCC2 VCC1 DEC2 DEC1 LIMIT ENABLE LIMIT OUT

(4-54)

IC451

41 42

(2/6)

TAPE TOP/END DETECT

44

TOP OUT

47

END OUT

(4-54)

IC451

95

96

31

28

38 40 39

71

15

DOP

44 85

54

87

11

10

59 60 12

SREEL FG

TREEL FG

XCC DOWN

(3/6)

34

40

VL UNREG

VIDEO LIGHT

DRIVE

Q702,703

3-11 3-12

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

3-6. SERVO BLOCK DIAGRAM

VC-251 BOARD

(4-56)

IC402

(2/2)

SERVO

DRUM SERVO

DRUM PWM

DRUM FG

DRUM PG

CAPSTAN SERVO

IC402 1

20.0 MHz

1.6Vp-p

D 2.8V

20MHz

VTR/CAMERA CONTROL

1

X0

X401

2

X1

120

VDD

101

AVRH

100

A VDD

64

VDD

25

VDD

CAP PWM

CFG HMS

DRUM START

DRUM ON

CAP ON

CAP FWD

( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.

IC451 wk

13 µsec

69 28

116

117

68 25

115

CAP FG

109

50 13 62 61

LPF

80mVp-p

IC451

PROTECT

(4-54)

LPF

IC451 wg 

(4/6)

13 µsec

DRUM ERROR

29

30 32

0.25V

VTR D/D ON

(IC503 )

27

CAP ERROR

50mVp-p

14 15

17

30

29

21 22

13

11 10

IC001

DRUM/CAPSTAN PWM DRIVE

OSC

PWM

(4-61)

SWITCHING

DRIVE

OUTPUT VCC 56

IC001 tk 

DRUM VS

0.75Vp-p

VTR UNREG

DRUM ON

DRUM START

D 2.8V

CONTROL

LOGIC

DRUM MOTOR DRIVE

COM

9 42 63 6

VCC2

VCC1

STBY

1

(4-54)

IC451

(5/6)

OUTPUT

DRIVE

BUFFER

SELSLP2

5 2

R408-410

DRUM DRIVE

CURRENT SENS

DRUM FG

DRUM PG

IC001 yf¢  

2.2 µsec

MT UNREG

58

1

64

Q012

SWITCING

MT UNREG

Q011

SWITCING

L006

MT UNREG

L005

OUTPUT

DRIVE

VS

IC451 tj,tl,ya»

5.6 msec

U V

W

RF

DRUM FG/PG WAVE SHAPER

16

SHAPER

22

61 59 57

(4-54)

IC451

WAVE

WAVE SHAPER

V REF

1.3Vp-p

CN706

4

9

10

7 8

5 6

(6/6)

3

18

LPF

2

19

1

20

B MECHA DECK

(SEE PAGE 4-53)

COM

M901

DRUM MOTOR

U

V

W

FG

FG-PG-COM

PG

FG

PG

IC402 rj 

25 Hz

2.8Vp-p

CN707

7

CAP VS

8

IC001

CAPSTAN FG

WAVE SHAPER

CAPSTAN MOTOR DRIVE

VCC

U IN 1 U IN 2

V IN 1 V IN 2

W IN 1 W IN 2

STBY

POWER

OFF

FRC

(2/2)

CFG(+)

CFG(-)

120°

LOGIC

CFG VCC

CAPSTAN FG

(4-45)

IC151

118

MECHA VD

111

MECHA FLD

19

XCS KINUTA

80

VC SI

79

VC SO

78

XVC SCK

47

SWP

44

ATF SAMPLE

16

94 89 98 96

REC Y RF

97 95

85 87

REC C RF

ATF

REC ATF

PB ATF

+

D/A

A/D

CAMERA/VIDEO(2) BLOCK

(4-50)

IC101

REC RF

7

6

REC/PB

AMP

PB C RF

49

11

VTR UNREG

VIDEO HEAD

CH SP1 27 28

CH SP2 33 34

IC451 qh 

5.6 msec

IC451 ws



2.8Vp-p

30 Hz

2.8Vp-p

(FOR CHECK)

CN713

16

8

RF SWP

CAP FG

(SEE PAGE 3-10)

CAMERA/VIDEO(2)

CAP ON

CAP FWD

CFG DUTY

(IC601 )

D 2.8V

8

VCC2

9

STANDBY

3

FRC

4

VCC1

10

FG OUT

1

OFFSET

ADJ

2

VTR UNREG

H1(+) H1(-)

H2(+) H2(-)

H3(+) H3(-)

CAP ON

POWER

IC001

(1/2)

VS

U

V

W

VH+

HE

VH-

CAP U

CAP V

CAP W

C HALL GND

H1(+) H1(-) H2(+) H2(-) H3(+) H3(-)

C HALL VCC

M902

CAPSTAN MOTOR

H

3-13 3-14

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

3-7. MODE CONTROL BLOCK DIAGRAM

CONTROL SWITCH BLOCK (CF-1000)

(TR MODEL) (TRV MODEL)

VOLUME

(TRV MODEL)

-

S013S016

VOLUME

+

S010(TR MODEL) S019(TRV MODEL)

(4-38)

IC001

LCD DRIVE

11

COM1

XCS

ı

C/XD

14

COM4

SD

SEG1

15

32

CONTROL SWITCH BLOCK(FK-1000)

(SEE PAGE 4-58)

SCK

ı

VDD

SEG18

S007

FF

( )

RV001 ZOOM

S007(TR MODEL) S010(TRV MODEL)

TITLE

S008(TR MODEL) S017(TRV MODEL)

COUNTER RESET

S011(TR MODEL) S022(TRV MODEL)

FADERFOCUS

9

10

8 7 6

D2.8V

LCD BLOCK ASSY

LCD

INDICATOR

(TRV MODEL)

LCD BLOCK ASSY

LCD

INDICATOR

(TR MODEL)

S902

PANEL

OPEN/CLOSE

CF-077 BOARD

S009(TR MODEL) S018(TRV MODEL)

CN009

1

2

1 ı

16

CN003

CN002

24 23

4

4 3

22

ı

18

5

BACK

LIGHT

( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.

CN001

XHI RESET

NOTE: TR MODEL/TRV MODEL

S006(TR MODEL) S007(TRV MODEL)

SEL/PUSH

EXEC DIAL

EXECUTE

(TRV MODEL)

DISPLAY

(TR MODEL)

S005

STOP ( )

PLAY ( )

REW

( )

EJECT

BZ001

BUZZER

S002

LIGHT

(VIDEO LIGHT MODEL)

S001

S006S008S009

PAUSE

( )

S005 DATE

S001

RESET

S004

EXPOSURE

S009S012

END

SEARCH

BT001 LITHIUM BATTERY

S002

MENU

TIME

XCS LCD DRIVER

LCD COM/XDATA

SUPER LASER

LINK

S012

(LASER LINK)

(LASER LINK MODEL)

S003

D 2.8V

OSD SO

XOSD SCK

EVER 3V

D2.8V

5

19

18 17

24

23

22

13

12

9 8 7 6

14

LI 3V

DIAL A DIAL B

KEY AD2

KEY AD3

KEY AD4

X CHARGE LED ON

BEEP

KEY AD0

KEY AD1

ZOOM VR

XIR LED ON LED 2.8V

XEJECT SW

20

6

7 8

1

2

3

12

IC503 r;

13

16 17 18 19 11

EVER 3.0V

CN709

CN710

7

5

1

10

8

11

D 2.8V

20.0 MHz

IC503 td



2.9Vp-p

32.768 kHz

X501

20MHz

X502

32.768kHz

3.0Vp-p

DIAL A

67

DIAL B

68

95

KEY AD2

KEY AD3

96

KEY AD4

97

X CHARGE LED

5

40

20MHz OUT

41

20MHz IN

52

32kHz IN

53

32kHz OUT

60

XCS LCD DRIVER

24

LCD COM/XDATA

93

KEY AD0

94

KEY AD1

7

XIR LED ON

17

XEJECT SW

IC503

MODE CONTROL

(4-58)

AVDD

XRESET

BATT IN

ACV SENS

BATT SENS

XCS VC

SYS V

XCC DOWN

HI SO

XHI SCK

MELODY

XWIND ON

HP SENS

TALLY LED

NS LIGHT ON

KEY AD5

VC-251 BOARD

D503

IC502

(4-57)

INITIAL RESET,

42 51

VDD

86 87

77

38

61

91 90

3 64 71

DEW

18

33

HI SI

34 35

36

58 31

55 43

98

6

5

4

BACKUP VCC

V OUT

RESET

CS

V BAT

7

V IN

EVER 3.0V

8

VRO

LI 3V

3

Q701

LED

DRIVE

D501

(4-57)

IC504

CHARGER

CN715

CN701

23

BATT UNREG (F001)

VTR UNREG (F002)

XSYS RST XCS VC SYS V DEW AD XCC DOWN

HI SI

HI SO XHI SCK ZOOM VR AD

(TRV MODEL)

BEEP

XWIND ON HP JACK IN

NS LIGHT ON

XTALLY LED

1

XSYS RST

1 2

KEY AD5

POWER

(SEE PAGE 3-26)

VTR/CAMERA CONTROL

(SEE PAGE 3-11)

AUDIO

(SEE PAGE 3-18)

(B/W EVF MODEL)

B/W EVF (VF-129)

(SEE PAGE 3-21)

(TRV MODEL)

LCD (PD-131)

(SEE PAGE 3-21)

CONTROL SWITCH BLOCK (SS-1000)

(SEE PAGE 4-58)

MI-040 BOARD

MI-041 BOARD

TRV MODEL : CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/

TRV88/TRV98/TRV98E

(TR MODEL)

(TRV MODEL)

S001 POWER CAMERA

OFF

PLAYER

(REMOTE COMMANDER MODEL)

REMOTE

1

COMMANDER

RECEIVER

IC751

(4-11)

S002

START/STOP

D752

TR MODEL : CCD-TR618/TR618E/TR718E/TR728E/TR818

VIDEO LIGHT MODEL : CCD-TR618/TR618E/TR718E/TR728E/TRV49/TRV49E/TRV58/TRV58E/

TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

LASER LINK MODEL : CCD-TRV98

B/W EVF MODEL : CCD-TR618/TR618E/TR718E/TR728E/TRV49/TRV49E/TRV58/TRV58E/

TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

REMOTE COMMANDER MODEL : CCD-TR728E/TRV49/TRV49E/TRV59E/TRV78/TRV78E/TRV98/TRV98E

3-15 3-16

(TALLY)

XCAM+STBY SW

XVTR MODE SW

XS/S SW

XSIRCS SIG

XFTALLY LED

CN713 (FOR CHECK)

16

CN711

1

2

4

CN703

16

24

6 4 2

LANC OUT LANC IN LANC POWER ON

15

XCAM+STBY SW

14

XVTR MODE SW

XS/S SW

16

XSIRCS SIG

4

XIR LED ON

6

2

LANC OUT

1

LANC IN

21

XLANC PWR ON

XSYS RST

XCS OSD

OSD SO XOSD SCK V JACK IN

XS JACK IN

CAM DD ON

IB SO

CHARGE INH

INIT CHARGE ON

FAST CHARGE

BATT/XEXT

VTR DD ON

9

44 45 46 84 85

28 48

IB SI

49

47 25 50 66

29

BLOCK

Q501

I/F

XSYS RST

XCS OSD OSD SO XOSD SCK V JACK IN XS JACK IN CAM DD ON

BATT SIG

CAM DD ON DC PACK SW INIT CHARGE ON FAST CHARGE BATT/XEXT SW VTR DD ON

CAMERA/VIDEO(2)

(SEE PAGE 3-10)

CAMERA/VIDEO(1)

(SEE PAGE 3-8)

POWER

(SEE PAGE 3-26)

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

3-8. AUDIO BLOCK DIAGRAM

VC-251 BOARD

CN713

BPF MON

13

(FOR CHECK)

PB RF

9

CAMERA/VIDEO(2)

(SEE PAGE 3-8)

A FADE

(IC601 )

PB RF

(IC101 )

AU BPF

(IC601 )

1.5M DEV

(IC601 )

REC AFM

(IC101 )

(IC151 )

1.7M DEV

(IC601 )

12

14

10

9

1

FSC

79

11

26

28

18

29

14

17

ST/MONO

19

( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.

(4-60)

IC351

AFM PROCESS

NR

PB 1.5M

BPF

PB 1.7M

AU 2.8V

MX MTX

NR

Q354

1.5M DEV

MOD/DEMOD

REC RF

FSC

1.7M DEV

DET

20 24 31 60 41 4643 48

AU 4.75V

932

MIC(L)

63

AGC

MIC(R)

2

IR(L)

55

HP(L)

52

LINE(L)

57

IR(R)

56

LINE(R)

58

HP(R)

54

MIX

POWER MUTE

21

22

23

59

MUTE SWITCH

SP+

49

SP-

51

BUS

DECODER

SPEAKER

AMP

SP VCC

MT 4.75V

MIX

(TRV MODEL)

Q355(1/2)

ON/OFF

VC SO

XVC SCK

XCS AU

Q352

Q355 (2/2)

CAMERA/VIDEO(1)

(SEE PAGE 3-8)

IR L OUT

IR R OUT

(LASER LINK MODEL)

BEEP

XWIND ON HP JACK IN

NS LIGHT ON

IR VIDEO

(IC221 )

(IC503 )

(IC503 ) (IC503 )

(IC503 )

24

(SEE PAGE 3-10)

36

58 31

43

CAMERA/ VIDEO(2)

MODE CONTROL

(SEE PAGE 3-16)

IR CARR

(IC601 )

IR V DEV

(IC601 )

IR A DEV

(IC601 )

6

21

7

NS LIGHT ON XWIND ON IR FSC

MIC R

CN703 CN753

8

9

4

10

7

6

11

15

1

23

CN709

22

21

13 14

CN702

AUDIO L I/O

8

IC3901 ra IR ON

(TRV MODEL)

HP JACK IN

HEADPHONE L

0.6Vp-p

H

A 4.75V

35 32 31

39

41

45

46

48

VCC VCC

VIDEO

SIGNAL

PROCESS

AUDIO

SIGNAL

PROCESS

7 12

FSC

(4-12)

18

IC752

12

MIC AMP

CONTROL SWITCH BLOCK (CF-1000)

3

4

SP+

12

SP-

11

CN001

FP-257

(FLEXIBLE)

MI-040 BOARD

HPF

27 25

OSC VCC

A 4.75V

INT MIC R

19

(SEE PAGE 4-33)

VIDEO I/O

(TR MODEL)

MIX

AMP

CN752

CN003

MI-041 BOARD

IC3901

IR TRANSMITTER

DRIVE

1

(HEADPHONES)

SP901

1

SPEAKER

2

A/V OUT

(4-13)

STBY

MIC

J001

J201

(TRV MODEL)

24

22

18

16

15

14

Q3901,3902

+

IR ON

LED

DRIVE

SIRCS PWM

IC3901 7 IR ON

IC3901 ws IR ON

0.5 µsec/div

D3901,3902

(LASER LINK)

Q3904

LED

DRIVE

(EXCEPT LASER LINK MODEL)

3.5795 MHz

D3903

(NS LIGHT)

0.2Vp-p

0.9Vp-p

TRV MODEL : CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/

47

(IC402 )

VC RF SWP XCS AU VC SI

VC SI

VC RF SWP

16

VC SO VC SCK

(IC402 ) (IC402 ) (IC402 ) (IC402 )

20 80 79 78

VTR/CAMERA CONTROL

(SEE PAGE 3-11)

TR MODEL : CCD-TR618/TR618E/TR718E/TR728E/TR818

LASER LINK MODEL : CCD-TRV98

TRV88/TRV98/TRV98E

3-17 3-18

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

3-9. LCD BLOCK DIAGRAM

PD-131 BOARD

(TRV MODEL)

10 11

3

4

5

8

7

9

6

CN5701

CAMERA/VIDEO (VC-251)

(SEE PAGE 3-9)

VTR/CAMERA CONTROL (VC-251)

(SEE PAGE 3-12)

PANEL R

PANEL G

PANELB

PANEL XVD

PANEL SYNC

XCS LCD DA

XVC SCK

VC SO

PANEL HOLD

( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.

IC5501 rk

IC5501 rj

H

IC5501 rh



H

0.5Vp-p

H

0.5Vp-p

SYNC XVD OUT XHD OUT

48

R

47

G

46

B

39

XSCK

40

SI

41

XCS

COM FRP29FRP30BLK32BGP

41 40 39 37

42

XSCK

44

XCS

45

SO

46

SI

48

XVD

1

HDI

3

W/H

47 2

36

POCB

(4-20)

IC5501

LCD DRIVER

78910

33

PD

29 27 26 25 28

(4-20)

IC5502

TIMING GENERATOR

VCC

11

VCO

XP.SAVE45XC.SAVE

COM OUT

EXT DA1 EXT DA2

38

MODE2 MODE1

BL DET

VCC1 VCC2

VCC3 VCC4

PSS2 PSS1

IC5501 w; 

IC5501 ws

Q5505

Q5502



IC5501 wf

Q5504

3.0Vp-p

2H

C5528

3.0Vp-p

2H

Q5503

PANEL 2.8V

42

PANEL 4.75V

25 16

VSH

26

PANEL 13.3V

15

20

VR

22

VG

24

VB

27 35 37

19

RES

24

SPD

23

CLD

22

CTR

21 20 18

EX2

17

PSG

16 15 14

EX1

13

SPS

12

CLS

30

VDD

8

LED

5

PANEL 2.8V

2H

PANEL 2.8V

PANEL 4.75V

PANEL -15.3V

PANEL 13.3V

3.0Vp-p

1K

PANEL 2.8V

GND

PANEL ID XHD OUT C SYNC VR PANEL COM VG XVD OUT VB

CN5501

10

9

6 8 7 5 4 3 2 1

19 20 21 11

4

23

13 18 17 16 15 14 10

9 8 7 6 5

12

24

3

1

CN5502 (FOR CHECK)

VR VG VB V COM

VGLAC VSH 3V

RES SPD CLD CTR PSS2 PSS1 EX2 PSG MO2 MO1 EX1 SPS CLS

VSH 5V

VGL

VGH

LCD901

LCD

PANEL

MODE CONTROL (VC-251)

(SEE PAGE 3-16)

POWER (VC-251)

(SEE PAGE 3-26)

XSYS RST

KEY AD5

BL REG

BL CONT

PANEL -15.3V

PANEL 13.3V PANEL 4.75V

PANEL 2.8V

TRV MODEL :

1

IC5502 1 

H

2

BL REG

18

17

L5601

Q5602

INVERTER

DRIVE

2.8Vp-p

(4-21)

IC5601

16 15 14 13

CN5701

Q5601

PWM EXT DA1 LED BL DET

16

PANEL 2.8V

1

INH

2

5

IC5502 wh

CONTROL SWITCH BLOCK (PR-10000)

CN5702

CN5601

1 2 5 6

BL HIGH

10

(SEE PAGE 4-19)

ND901

(BACKLIGHT)

S001

PANEL

REVERSE

6 MHz

T5601

1 5 2 3 4

10

6

(4-21)

3.0Vp-p

C5607

IC5602

D5601

6

7

BL

5 4

RECT

3

DET

PANEL 4.75V

Q5603

BL LOW

3

2 1

CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/ TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

3-19 3-20

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

3-10.B/W EVF BLOCK DIAGRAM

VF-129 BOARD

MODE CONTROL

(VC-251)

(SEE PAGE 3-16)

CAMERA/VIDEO

(VC-251)

(SEE PAGE 3-9)

XTALLY LED

EVF Y

4 3

CN901

( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.

(B/W EVF MODEL)

IC901 qh

2.4Vp-p

EVF 4.75V

D901

(TALLY)

IC901 qa

H

0.9Vp-p

H

IC901 qd

H OUT

(4-25)

IC901

VCC VCC

2 12

SYNC

SEP

V SYNC

SEP

11 14

8 6 7

AFC

OSC

V

15 9 16 13

H

OSC

VIDEO AMP/BLKG MIX

V

OUT

5

H

DRIVE

IC901 3 

3

1

Q903

VIDEO

AMP

SOL901

16.7 msec

IC901 1,5

H

C909

H SIZEQ902

16.7 msec

2.0Vp-p

1.1Vp-p

2.0Vp-p

Q904

VIDEO DRIVE

EVF 4.6V

D903

DUMPER

T902

FBT

2

1

3

4

5

NOT USED

T901

FBT

4

5

6

7

86

W901

G1

1

H

W901

CN902

2

H

3

HV

G2

5

DH2

4

DH1

3

2

7

81

RV904

BRIGHT

EVF 4.75V

V901

DEFLECTION

YOKE

HV

PICTURE TUBE

EVF 4.6V

IC901 7 

16.7 msec

1.1Vp-p

RV903 V SIZE

B/W EVF MODEL :16CCD-TR618/TR618E/TR718E/TR728E/TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

3-21 3-22

DV2

2

DV1

1

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

3-11.COLOR EVF BLOCK DIAGRAM

EVF R

EVF G

CAMERA/VIDEO

(VC-251)

(SEE PAGE 3-9)

EVF B

PANEL XVD

PANEL XHD

( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.

VF-141 BOARD

IC4501 rk

(COLOR EVF MODEL)

0.50Vp-p

16

15

14

11

12

CN4501

IC4501 rj

IC4501 rh

2H

0.43Vp-p

2H

0.5Vp-p

R

48

G

47 46

B

XSCK

39 40

SI XCS

41

30 32 33 2 3 4 5 11

FRP

40 39 37 35 34 33 32 29 27 26 25 28

42 XSCK 44 XCS 45 SO 46 SI

48 XVD

1 HDI

BLK

BGP

SHR

(4-30)

IC4501

LCD DRIVE

78910

SHG

SHB

SHA

(4-30)

IC4502

TIMING GENERATOR

IC4501 w;

7.2Vp-p

2H

VCC1

42

VCC2

25 15

VCC3

VR

20

VG

22 24

VB

12COM DC

VCO

45 38

VCO

PD

XP.SAVE

HCK1 HCK2

DWN/CLR

BLK

RGT

VCK

VST

IC4501 wf 

XC.SAVE

24 23 22 21HST 20 18 17

EN

16STB 15 14

EVF 2.8V EVF 13.3V

2H

7.2Vp-p

IC4501 ws



2H

7.2Vp-p

14 15 13 16

12 11 10

9 8 7 6 5 4 3

VR VG VB COM

BLK HCK1 HCK2 HST RGT DCG/OLR EN STB VCK2 VST

LCD902

LCD

PANEL

CN713 (FOR CHECK)

VCO

1

EVF VG

7

EVF BL

3 5

EVF BL 4.75V

(Q008)

VC-251 BOARD

16

VTR/CAMERA

CONTROL

(VC-251)

(SEE PAGE 3-12)

POWER

(VC-251)

EVF BL 4.75V

R073,074

XCS EVF DA

XVC SCK

VC SO

EVF 13.3V

EVF 2.8V

6

15

17 18

CN708

8 7 6

5

17 18

1

3

13

4

2

6

4

PWM

DET VCO EVF VG

PWM

DET

CN4601

EVF 13.3V

EVF 2.8V

1

2

IC4601

19VDD

VDD

XHD OUT

2

IC4502 wh

10.86 MHz

T4601

10

6

ND4601

(BACKLIGHT)

R4601

LB-062 BOARD

IC4601 4

H

4.6Vp-p

Q4601

INVERTER

4

DRIVE

2

4

(4-32)

1.3Vp-p

PWM

LED

43

9 9

10-IN

EVF 2.8V

COLOR EVF MODEL :

EVF 13.3V

CCD-TR818

CN4502

VDD

1

3-23 3-24

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

3-12.POWER BLOCK DIAGRAM (1/2)

TRV MODEL : CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/

TR MODEL : CCD-TR618/TR618E/TR718E/TR728E/TR818

B/W EVF MODEL : CCD-TR618/TR618E/TR718E/TR728E/TRV49/TRV49E/

COLOR EVF MODEL : CCD-TR818

(TRV MODEL)

15 14 16

13

18 17

CN5701

16

TRV78/TRV78E/TRV88/TRV98/TRV98E

TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

PD-131 BOARD

PANEL 13.3V PANEL 4.75V PANEL -15.3V

PANEL 2.8V

BL REG BL CONT

(4-20)

IC5501

LCD

DRIVE

BACK LIGHT DRIVE

(4-20)

IC5502

TIMING

GENERATOR

IC5601 IC5602

Q5502-5506

(4-21)

( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.

VC-251 BOARD

DC PACK SW

BATT SIG

BATT/EXT SW

INIT CHARGE ON

FAST CHAREG

Q010

SWITCHING

Q009

SWITCHING

Q007

SWITCHING

Q008

SWITCHING

(TRV MODEL)

Q006

SWITCHING

SERVO BLOCK

Q014,015 DRUM VS

CAP VS

SWITCHING

F001

L004

L007

L011

T001

2

3

4

1

5

6

8

L002

L001

L003

VSH 5V

VHS 3V

CN5501

BL HIGH

CN5601

BT901

BATTERY

TERMINAL

S

DC IN

BATT UNREG

DC PACK SW

BATT SIG

BATT GND

BATT/EXT

ACV UNREG

ACV GND

4

1

7

5

3

6

2

CN001

Q002

(TRV MODEL)

Q001,003,004

F004

F003

F002

CHARGE

CONTROL

BL UNREG

MT UNREG

VTR UNREG

(4-61)

(1/2)

IC001

DC/DC CONVERTER

45

OUTPUT-1

42

MOS GATE-1

VCC

28

OUTPUT MONITOR-1

CT

22

RT

21

OUTPUT MONITOR-4

OUTPUT VCC 1.2.3

OUTPUT MONITOR-3

OUTPUT MONITOR-2

OUTPUT MONITOR-7

MONITOR INPUT-7

LCD901

VGH

1

24

VGL

LCD

3

PANEL

23

ND901

10

BACK

LIGHT

DRUM/CAPSTAN

PWM DRIVE

OUTPUT VCC 4.5.6

OUTPUT-4

OUTPUT VCC 7

COMP

OUTPUT-3

OUTPUT-2

OUTPUT-7

STANDBY-3

STANDBY

STANDBY-7

VREF

40

57

18

5

49

41

50

34

46

37

2

6

7

29 30

31

27

1

Q014,015

4.75V REG

L008 D 2.8V

L009 A 2.8V

L010 AU 2.8V

FB001 EVF 2.8V

D007(1/2)

D007(2/2)

D010

L012 EVF PANEL 4.75V

L013 AU 4.75V

L014 A 4.75V

L016 RP 4.75V

BL REG

BL CONT

D006

RECT

EMERGENCY

DETECT

Q018

Q022,023 +15V REG

(TRV MODEL)

-15.3V REG

Q027,028

Q019,021

-7.0V REG

(COLOR EVF MODEL)

FB002

(TRV MODEL)

FB003 PANEL 13.3V

PANEL -15.3V

BATT SIG

BATT/XEXT SW

FAST CHARGE

DC PACK SW

INIT CHARGE ON

BATT UNREG

VL UNREG

MT 4.75V

VTR UNREG

CAM -7.0V

CAM 15V

EVF 2.8V

EVF 13.3V

EVF PANEL 4.75V

AU 4.75V

RP 4.75V

CAM DD ON

VTR DD ON

(TRV MODEL)

PANEL 2.8V PANEL 4.75V PANEL 13.3V

PANEL -15.3V

BL CONT

D 2.8V

A 2.8V

AU 2.8V

D 1.5V

A 4.75V

BL REG

CN701

POWER(2)

(SEE PAGE 3-27)

13 14 15 16 17 18

3-25 3-26

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

3-13.POWER BLOCK DIAGRAM (2/2)

VC-251 BOARD

BATT SIG

BATT/XEXT SW FAST CHARGE DC PACK SW INIT CHARGE ON BATT UNREG

VL UNREG

MT 4.75V

VTR UNREG

D 2.8V

A 2.8V

AU 2.8V

D 1.5V

CAM -7.0V

CAM 15V

EVF 2.8V

EVF 13.3V

EVF BL 4.75V

AU 4.75V

A 4.75V

BP 4.75V

CAM DD ON

VTR DD ON

CN712

913

T REEL, S REEL,

SENSOR

TRV MODEL : CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

REMOTE COMMANDER MODEL : CCD-TR728E/TRV49/TRV49E/TRV59E/TRV78/TRV78E/TRV98/TRV98E

TR MODEL : CCD-TR618/TR618E/TR718E/TR728E/TR818

LASER LINK MODEL : CCD-TRV98

VIDEO LIGHT MODEL : CCD-TR618/TR618E/TR718E/TR728E/TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

STEADY SHOT MODEL : CCD-TR818/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

B/W EVF MODEL : CCD-TR618/TR618E/TR718E/TR728E/TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

COLOR EVF MODEL : CCD-TR818

16

POWER(1)

(SEE PAGE 3-26)

D501

IC504

CHARGER

2

(4-57)

(4-52)

IC221

VIDEO

OUT

AMP

(4-60)

IC601

D/A CONV. (EVR)

MECHA/CAMERA/SERVO

R457R461,462

CN707

H001 H002

( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.

(4-58)

IC503

MODE CONTROL

14

XVTR MODE SW

15

XCAM+STBY SW

90

BATT SENS

91

ACV SENS

42

(4-45)

9

VIDEO

HEAD

Q501

51 77

VDD

86 87

38

RESET

61

BATT IN

48

IB SI

I/F

49

IB SO

CAM DD ON

VTR DD ON

DC PACK SW

FAST CHARGE

BATT/EXT

INIT CHARGE ON

28 29 47 50 66

25

(4-43)

IC272

S/H.AGC.

A/D CONV.

(4-43)

IC271

TIMING

GENERATOR

24 15

ZOOM

LENS

(4-48)

IC302

IRIS DRIVE HALL AMP

(4-47)

IC301

FOCUS/ZOOM

MOTOR DRIVE

(4-8)

CN271

CN191

(4-60)

IC351

AUDIO

PROCESS

SPEAKER

AMP

R306

L101

13

CN301

IC191

CD-286 BOARD

CD-281 BOARD

(TRV MODEL)

D503

3

(4-56)

IC402

CONTROL

910

CAPSTAN

MOTOR

V IN

3

V BATT

INITIAL RESET, BACKUP VCC

IC502

RESET

5

EVER 3.0V

8

VRO

4

CS

(4-57)

6

V OUT

7

(4-46)

IC153

CHARACTER GENERATOR

VL UNREG MT 4.75V D 2.8V A 2.8V AU 2.8V

D 1.5V CAM -7.0V CAM 15V

EVF BL 4.75V

AU 4.75V

A 4.75V A 4.75V

BP 4.75V VTR UNREG

CAMERA Y/C PROCESS,

VTR Y/C PROCESS,

ATF,

FOCUS/ZOOM MOTOR

CONTROL

IC151

Q151

AFC

(4-56)

IC401

EEPROM

71

V LIGHT PWM

10

EVF DD ON

DRUM MOTOR

MOTOR DRIVE,

SENSOR AMP

IC451

M902

DRIVE,

LOADING

(4-54)

B MECHA DECK

(SEE PAGE 4-53)

(4-50)

IC101

REC/PB

AMP

L103

CN101

10 12

53

CCD

IMAGER

(TR MODEL)

R711

VL UNREG

V LIGHT PWM

(VIDEO LIGHT MODEL)

CN711

CN709

CN710

CN703

Q702,703

CN702

VL UNREG

1 2

6

19

916

10

15

11

14

20

5

2

6

8

14

13

12

5

VIDEO

LIGHT

DRIVE

20 19

VIDEO LIGHT

XCAM+STBY SW XVTR MODE SW

CN001

D 2.8V

A 2.8V

AU 2.8V

A 4.75V

VTR UNREG

CN753

LI-3V

D 2.8V

EVER 3.0V

XHI RESET

FP-257

CURRENT

LIMITER

LCD INDICATOR

S001

RESET

ZOOM VR

SWITCH

LED

Q704,705

(FLEXIBLE)

BT001 LITHIUM BATTERY

IC001

DRIVE

(4-38)

(4-12)

IC752

MIC AMP

D3901,3902 LASER LINK

LED

(LASER LINK MODEL)

21

RFU DC OUT

J202

RFU DC OUT

S001

POWER

CAMERA

OFF

PLAYER

CF-077 BOARD

(TR MODEL) (TRV MODEL)

CONTROL SWITCH BLOCK(FK-1000)

(SEE PAGE 4-58)

COMMANDER

(REMOTE COMMANDER MODEL)

EVF PANEL 4.75V

EVF 13.3V

EVF 2.8V

EVF DD ON

Q071,072

(TRV MODEL)

CONTROL SWITCH BLOCK(SS-1000)

(SEE PAGE 4-58)

SWITCH

CONTROL SWITCH BLOCK(CF-1000)

(SEE PAGE 4-33)

(4-11)

IC753

PITCH, YAW

SENSOR AMP

(4-11) (4-13)

IC751

REMOTE

RECEIVER

R073,074

(TR MODEL)

PITCH, YAW

SENSOR

(STEADY SHOT MODEL)

IC3901

IR

TRANSMITTER

(LASER LINK MODEL)

R710

R711

(B/W EVF MODEL)

MI-040 BOARD

SE751,752

MI-041 BOARD

(EXCEPT LASER LINK MODEL)

CN715

1

BW EVF 4.75V

1

CN901

(4-25)

IC901

CRT

DRIVE

VF 129 BOARD

NIGHT SHOT

EVF BL 4.75V EVF BL

EVF 13.3V

EVF 2.8V

EVF BL

(TRV MODEL)

D3903

LED

(TR MODEL)

5 3

14

2 1

17 18

CN713 (FOR CHECK)

VF-141 BOARD

5

17 18

LB-62 BOARD

CN4601

2

(COLOR EVF MODEL)

FB4502

IC4501

LCD

DRIVE

(4-30)

IC4502

TIMING

GENERATOR

(4-32)

IC4601

BACK LIGHT

DRIVE

(4-30)

LCD903

CN4502CN4501CN708

1

LCD

PANEL

3-27 3-28E

SECTION 4

PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

4-1. FRAME SCHEMATIC DIAGRAM (1/2)

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

1

38

5 13

6

924 7

A

10

CD-281 BOARD

CD-286 BOARD

LENS UNIT

B

C

B200 MECHANISM(NTSC MODEL) B201 MECHANISM(PAL MODEL)

COM_GND

M903 LOADING

M

D

MOTOR

S901 MODE SWITCH

E

VIDEO HEAD

F

G

M901 DRUM MOTOR

FG

M

PG

H

M901 CAPSTAN

I

MOTOR

FG

DEW SENSOR

M

J

FP-355

FLEXIBLE

K

FP-249

FLEXIBLE

FP-356

FLEXIBLE

L

TR MODEL :CCD-TR618/TR618E/TR718E/TR728E/TR818

M

TRV MODEL:CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

M-SW(A)

M-SW(B)

M-SW(C)

FG-PG_COM

FG_OUT

OFFSET_ADJ

STAND_BY

MT_GND

REG_GND

TAPE_TOP(C)

HI8_MP

S_REEL(-)

S_REEL(+)

REC_PROOF

TAPE_END(C)

TAPE_LED(A)

HALL_COM

T_REEL(-)

T_REEL(+)

SENSOR_VCC

TAPE_LED(K)

C_LOCK_SW

VCC_2

VCC_1

ME/MP

LM(-)

LM(+)

COM

LP2Y

LP2X

GND

LP1X

LP1Y

GND

SP1Y

SP1X

GND

SP2X

SP2Y

GND

FEY

FEX

PG

FG

W W

V

V U U

FRC

VS

DEW

1

2

3

4

5

6

FLEXIBLE

7

FP-220

8

1

2

3

4

5

6

7

8

9

10

FLEXIBLE

11

12

13

14

15

16

1

2

3

4

5

6

7

8

9

10

1

2

3

4

5

6

7

8

9

FLEXIBLE FLEXIBLE

10

11 12

1

2

3

4

5

6

7

8

FLEXIBLE

9

FP-221

10

11

12

13

14

15

COM_GND

M-SW(A)

M-SW(B)

M-SW(C)

LM(-)

LM(+)

LP2Y

LP2X

GND

LP1X

LP1Y

GND

XODD

YODD

GND

XEVEN

YEVEN

GND

FEY

FEX

PG FG-PG_COM FG COM W W V V U U

FG_OUT

OFFSET_ADJ

STAND_BY

FRC

MT_GND

VS

VCC_2

VCC_1

REG_GND

DEW

REG_GND

TAPE_TOP(C)

HI8_MP

S_REEL(-)

S_REEL(+)

ME/MP

REC_PROOF

TAPE_END(C)

TAPE_LED(A)

HALL_COM

T_REEL(-)

T_REEL(+)

SENSOR_VCC

TAPE_LED(K)

C_LOCK_SW

CN712

CN704 8P

CN706

CN707 12P

16PCN101

10P

15P

123456789

FC_B

FC_A

FC_XA

FC_XB

ZM_ZB

ZM_XA

24P

CN291

11121314151617181920212223

10

PLA/GLASS

FC_SENSE_VCC

ZM_SENSE_VCC

GND

FC_SENSE_OUT

ZM_SENSE_OUT

ZM_B

ZM_A

TEMP

BIAS(+)

VC-251 BOARD(1/2)

1/11 CAMERA PROCESSOR AMP 7/11 MODE CONTROL 2/11 Y/C PROCESSOR 3/11 FOCUS/ZOOM/MOTOR DRIVER 9/11 AUDIO

5/11 LINE IN/OUT AMP 6/11 SERVO

XS_JACK_IN

S_C_I/O

UNREG_GND

VL_UNREG

UNREG_GND

VL_UNREG

VIDEO LIGHT

EXCEPT TR818

G

J201

S VIDEO OUT

A/V OUT

RFU DC OUT

J202

C

Y

G

BIAS(-)

HALL(-)

HALL(+)

NIGHT_SHOT

8/11 HI CONTROL 10/11 DC/DC CONVERTER4/11 REC/PB AMP

11/11 CONNECTOR

S_Y_I/O

REG_GND

AUDIO_R_I/O

FP-257

CONT(+)

REG_GND

DRIVE(-)

VIDEO_I/O

1011121314151617181920

24

DRIVE(+)

REG_GND

CCD IMAGER

AUDIO_L_I/O

V_JACK_IN

FLEXIBLE

REG_GND

NC

RF_DC_OUT

123456789

14P

CN191

V4V3V2V1GNDRGH1H2GND

123456789

V4

14P

CN271

20P

CN702

11 1514

12

(TRV MODEL)

(TR MODEL)

CAM_-7.5V

VSHT

CAM_15V

GND

CCD_OUT

111213

10

VSHT

CAM_-7.0V

24P

CN703

CAM_15V

(FOR CHECK)

XF_TALLY_LED

123456789

14

GND

CCD OUT

VCO

1

XLANC_POWER_ON

2

EVF_BL

3

LANC_IN

4

EVF_BL_4.75V

5

LANC_OUT

6

EVF_VG

MIC_L

SE_GND

YAW_AD

PITCH_AD

7

CAP_FG

8

PB_RF

9

REG_GND

10

REG_GND

11

REG_GND

12

BPF_MONI

13

IR_VIDEO

14

REC_RF

15

RF_SWP

16

NC

17

NC

18

NC

19

NC

20

XSIRCS_SIG

VST_C_RESET

XWIND_ON

MIC_R

CPC

REG_GND

FP-259

V1

V3

V2

1011121314

FLEXIBLE

H1

H2

RG

GND

FP-263

MIC_R

MIC_L

YAW_AD

SE_GND

REG_GND

PITCH_AD

24P

XF_TALLY_LED

CN753

MI-040 BOARD MI-041 BOARD

1/2 STEADY SHOT,MIC AMP

2/2 IR

D3903

IC3901

IR

SIRCS

XWIND_ON

XSIRCS_SIG

VST_C_RESET

(TR MODEL) (TRV MODEL)

SE752 YAW

SENSOR

CONTROL SWITCH BLOCK(FK-1000)

EJECT/ VIDEO LIGHT/

123456789

ZOOM_VR

12PCN710

A_4.75V

A_2.8V

AU_2.8V

IR_ON

S0001,002,005-009

PAUSE/STOP/ /

PLAYREW/

D_2.8V

REG_GND

20PCN713

IR_CARR

IR_V_DEV

IR_A_DEV

101112131415161718192021222324

KEY_AD1

XPHOTO_FREEZE

IR_L_OUT

FF

D_2.8V

IR_R_OUT

KEY_AD0

VTR_UNREG

IR_VIDEO

LED_2.8V

REG_GND

NC

REG_GND

RV001

ZOOM

S012

D001

SUPER LASER LINK

101112

XIR_LED_ON

FLEXIBLE

101112131415161718192021222324

IR_ON

A_2.8V

AU_2.8V

A_4.75V

SE751 PITCH

SENSOR

IR_A_DEV

IR_V_DEV

IR_CARR

IR_L_OUT

IR_R_OUT

VTR_UNREG

CN751

CN752 2P

IR_VIDEO

XX

REG_GND

INT_MIC_L

INT_MIC_R

REG_GND

MIC_GND

XEJECT_SW

IR_FSC

123456789

IR_FSC

REG_GND

CCD-TRV98

1

2

1

2

TO FH(2/2)

MIC901 INT_MIC_R

MIC

1716 18

16

FRAME SCHEMATIC DIAGRAM (1/2)

4-1 4-2

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

FRAME SCHEMATIC DIAGRAM (2/2)

11 1514

4N.C

5N.C

6N.C

7N.C

8N.C

9N.C

10BL_HIGH

12

123456789

VGL

SPS

VGH

GND

VGLAC

24P

CN5501

ND901

BACK LIGHT

LCD901

2.5/3/3.5 INCH

101112131415161718192021222324

EX2

EX1

PSG

MO1

MO2

PD-131 BOARD

(FOR CHECK)

PANEL_2.8V

PANEL_13.3V

PANEL_-15.3V

PANEL_13.3V

PANEL_-15.3V

PANEL_4.75V

PANEL_2.8V

REG_GND

XVC_SCK

XCS_LCD_DA

1011121314151617181920

PD-110

HARNESS

1011121314151617181920

XVC_SCK

XCS_LCD_DA

VC_SO

PANEL_XVD

C-SYNC

PANEL_HOLD

PANEL_B

PANEL_R

PANEL_G

AD5

XSYS_RSTXSYS_RST

123456789

AD5

PANEL_G

PANEL_R

PANEL_B

BL_CONT

CLS

VCOM

CPC

RES

PSS2

PSS1

20P

CN708

EVF_BL_GND

EVF_BL/BW_EVF_4.75V

XTALLY_LED

EVF_13.3V

XCS_EVF_D/A

CTR

1

2

3

4

5

6

7

8

9

10

XVC_SCK

EVF_GND

EVF_XVD

EVF_XHD

EVF_2.8V

CLD

VB XVD_OUT VG

PANEL_COM

VR N.C.

C-SYNC/XHD XHD_OUT

GND GND

EVF_VG

XVC_SO

EVF_B

EVF_G

EVF_R

1716 18

19

(TRV MODEL)

VB

VR

VG

SPD

GND

VSH3V

VSH5V

6P

10PCN5502

CN5703

PANEL_REV

1 2

3

N.C.

4

N.C.

5

GND

6

GND

CONTROL SWITCH BLOCK (PR-10000)

S001

(PANEL REVERSE)

(TR818)

FLEXIBLE

VF-141 BOARD

CN4501

18

EVF_2.8V

17

EVF_2.8V

16

EVF_R

15

EVF_G

14

EVF_B

13

VCO

12

EVF_XHD

11

EVF_XVD

10

EVF_GND

9

EVF_GND

8

VCS_EVF_D/A

7

XVC_SCK

6

VC_SO

5

EVF_12.0V

4

EVF_VG

3

XTALLY_LED

2

EVF_BL_4.75V

1

EVF_BL_GND

18P

CN4502

(12.0V)

16P

1

VVDD

2

VSS

3

VST

VCK2

4

VCK1

5

6

EN

CLR

7

RGT

8

HST

9

10

HCK2

11

HCK1

BLK

12

B

13

R

14

G

15

COM

16

LCD 903

COLOR

ND4601 BACK LIGHT

LCD

UNIT

20

19

18

17

16

15

14

13

12

11

10

9

8

FP-151

7

6

VCO

5

4

3

2

1

10P

CN5604

20P

CN5701

20P

CN701

10

1LED_GND

SE_GND

2LED

BL_GND

3BL_LOW

BL_REG

1

A

16

15

14

B

LCD 902

CHARACTER

D901

DISPLAY

EL

C

D

E

SP901

SPEAKER

OPEN/CLOSE

13

12

11

10

9

8

7

6

5

4

3

2

1

1-EL

2-EL

3

4

5-EL

6-EL

7

8

1 SP(+)

2 SP(-)

S902

1 OPEN/CLOSE

2 GND

38

S001-005,009,010,012,013,015-019,022

8PCN004

2P

(TR MODEL)

(TRV MODEL)

RESET/MENU/TIME/EXPOSURE/

DATE/END SEARCH/TITLE/

DISPLAY/VOLUME+/VOLUME-/

COUNTER RESET/BACK LIGHT/

FOCUS/FADER

S007

SEL/PUSH EXEC

CF-077 BOARD CONTROL SWITCH BLOCK

16P

CN003

COM1

COM2

SEG3 SEG4 SEG5

SEG6 SEG7

SEG8 SEG9

SEG10

SEG11 SEG12

SEG13

SEG14

COM4

COM3

CN003

CN009

F

G

TO FH(1/2)

5 13

(CF-1000)

J001

(HEADPHONES)

6

123456789

COM3

COM4

SEG17

BL_GND

BL_VDD

26P

CN006

S001-005,S007-011

RESET/MENU/TIME/EXPOSURE/

DATE/TITLE/COUNTER RESET/

BACK LIGHT/FOCUS/FADER

24PCN001

KEY_AD4

KEY_AD2

KEY_AD3

123456789

KEY_AD2

KEY_AD4

KEY_AD3

24P

CN709

LCD 902

CHARACTER DISPLAY

1011121314151617181920212223242526

SEG18

BL_GND

SEG16

SEG15

LI_3V

LCD_LED_ON

LI_3V

LCD_LED_ON

SEG1

DIAL_A

SEG14

DIAL_B

SEG8

SEG9

SEG7

SEG12

SEG13

SEG10

SEG11

BZ001 (BUZZER)

SP-

VTR_UNREG

EVER_3.0V

XCHARGE_LED_ON

REG_GND

D_2.8V

SP+/BEEP

101112131415161718192021222324

FFC-295

FLAT CABLE

101112131415161718192021222324

SP-

D_2.8V

REG_GND

SP+(BEEP)

EVER_3.0V

VTR_UNREG

XCHARGE_LED_ON

(TR MODEL)

SEG6

SEG5

SEG4

S006

SEL/PUSH EXEC

LITHIUM BATTERY

OSD_SO

XCS_LCD_DRIVER

LCD_COM/XDATA

OSD_SO

LCD_COM/XDATA

XCS_LCD_DRIVER

SEG3

BT001

XOSD_SCK

SEG2

+

XHI_RESET

COM2

COM1

HEADPHONE_L

HP_JACK_IN

HEADPHONE_L

BL_GND

BL_VDD

HEADPHONE_GND

HEADPHONE_R

123456789

HEADPHONE_R

HEADPHONE_GND

924 7

H

VC-251 BOARD(2/2)

I

J

K

L

M

N

O

16

FRAME SCHEMATIC DIAGRAM (2/2)

TR MODEL :CCD-TR618/TR618E/TR718E/TR728E/TR818 TRV MODEL :CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

CONTROL SWITCH BLOCK (SS-1000)

S002

START/STOP

PLAYER

OFF(CHARGE)

CAMERA

POWER

XCAM+STBY_SW

S001

1

2

3

4

5

XVTR_MODE_SW

REG_GND

XS/S_SW

REG_GND

5PCN711

CN715

EVF_BL/BW_EVF_4.75V

4-3 4-4

4P

XTALLY_LED

BW_EVF_Y

EVF_GND

7PCN001

DCPACK_SW

BATT/XEXT

BATT_UNREG

BATT_GND

ACV_UNREG

ACV_GND

BATT_SIG

FFC-256

FLAT CABLE

4

3

2

1

2

3

4

5

6

7

DP-77

HARNESS

EVF_BL_GND

1

EVF_BL_4.7.5V

2

XTALLY_LED

3

DET

4

LED_K

5

6

PWM

VF-129 BOARD

CN901 1 EVF_4.6V

2 EVF_GND

3 BW_EVF_Y

4 XTALLY_LED

6PCN4601

LB-062 BOARD

4P

W901

BT901 BATTERY

TERMINAL

BL-HIGH

BL-LOW

GND

FTB

1G1

2H

3H

4N.C.

5G2

CN902

4P

1DV1

2DV2

3DH1

4DH2

(EXCEPT TR818)

V901 CRT

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block)

(For printed wiring boards)

• b: Pattern from the side which enables seeing. (The other layers' patterns are not indicated.)

• Through hole is omitted.

• Circled numbers refer to waveforms.

• There are few cases that the part printed on diagram isn’t

mounted in this model.

• Chip parts.

Transistor Diode

C

5

BE

64

2

13

5

46

2

31

45

2

31

12

4

53

3

21321321

(For schematic diagrams)

• All capacitors are in mF unless otherwise noted. pF : m mF. 50V

or less are not indicated except for electrolytics and tantalums.

• Chip resistors are 1/10W unless otherwise noted.

kW=1000W, MW=1000kW.

• Caution when replacing chip parts.

New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Be-

cause it is damaged by the heat.

• Some chip part will be indicated as follows.

Example C541 L452

22U 10UH TA A 2520

Kinds of capacitor

Temperature characteristics

External dimensions (mm)

• Constants of resistors, capacitors, ICs and etc with XX indicate

that they are not used.

In such cases, the unused circuits may be indicated.

• All variable and adjustable resistors have char acteristic curve B,

unless otherwise noted.

• Signal name

XEDIT→ EDIT PB/XREC → PB/REC

• 2 : non flammable resistor

• 1 : fusible resistor

• C : panel designation

• A : B+ Line *

• B : B– Line *

• J : IN/OUT direction of (+,–) B LINE. *

• C : adjustment for repair. *

• Circled numbers refer to waveforms. *

*Indicated by the color red.

Note :

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Note :

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

(Measuring conditions voltage and waveform)

• Voltages and waveforms are measured between the measurement points and ground when camera shoots color bar chart of pattern box. They are reference values and reference wavefor ms . * (VOM of DC 10 MΩ input impedance is used.).

• Voltage v alues change depending upon input impedance of V OM used.) *

1. Connection

Pattern box

1.5 m

Front of the lens

2. Adjust the distance so that the output waveform of Fig. a and

the Fig. b can be obtain.

H

Yellow

Cyan

White

Magenta

Green

AABBA=B

Fig. a (Video output terminal output waveform)

Cyan

White

Green

Yellow

Magenta

Red

Blue

Red

Blue

Electron beam scanned frame

CRT picture frame

Fig.b (Picture on monitor TV)

When indicating parts by reference number, pleas include the board name.

4-5

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

CD-281/286 (CCD IMAGER) PRINTED WIRING BOARD

— Ref. No. CD-281/286 Board; 1,000 Series —

For printed wiring board

• Refer to page 4-70 for parts location.

• CD-281/286 board consists of multiple layers. However, only the sides (layers) A and B are shown.

• Chip parts Transistor

C

BE

There are a few cases that the part printed on this diagram isn’t mounted in this model.

CD-286 (TR model) CD-281 (TRV model) (CCD IMAGER)

MI-040 (TR model) MI-041 (TRV model) (STEADY SHOT, MIC AMP, IR DRIVE)

CONTROL SWITCH BLOCK (CF-1000) (TRV model)

PD-131 (TRV model) RGB, TIMING GENERATOR, BACK LIGHT

For Schematic Diagram

• Refer to page 4-66 for waveforms.

3

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

14

13

12

11

10

9

8

7

6

5

4

3

2

1

C196

47u 10V

R194

R195

XX

0

R-4.7/P0

1V32V23V14

V4

CD-281 BOARD CD-286 BOARD

A

B

CCD IMAGER

-REF.NO.:1000 SERIESXX MARK:NO MOUNT

TO VC-251 BOARD(1/11) CN271

THROUGH THE FP-259 FLEXIBLE

(SEE PAGE 4-43)

C

1

24

(TRV MODEL) (TR MODEL)

CN191

14P

V4

V3

V2

V1

GND

RG

H1

H2

CAM_-7.5V/-6.5V

GND

VSHT

CAM_15V/12V

GND

CCD OUT

5

H2

IC191 *

14

D

R192

E

SIGNAL PATH

VIDEO SIGNAL

CHROMA

Y/CHROMAY

REC

PB

F

NTSC MODEL :CCD-TR618/TR818/TRV49/TRV58/TRV68/TRV78/TRV88/TRV98 PAL MODEL :CCD-TR618E/TR718E/TR728E/TRV49E/TRV58E/TRV59E/TRV78E/ TRV98E 1/6 CCD MODEL :CCD-TR618/TR618E/TR718E/TR728E/TRV49/TRV49E/TRV58/TRV58E/ TRV59E 1/4 CCD MODEL :CCD-TR818/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E TRV MODEL :CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/ TRV88/TRV98/TRV98E

G

TR MODEL :CCD-TR618/TR618E/TR718E/TR728E/TR818

L191

100uH

R191

1608

10

R1.4/P0

0

C191

22u

16V

R8.5/P0

1

R-4.7/P0

R1.6/P0

R198

*

R12.0/P0

R193

10K

1608

4

R9.9/P0

56

2

IC191

CCD IMAGER

3

R-0.2/P0

5

VL(CSUB)

SHT(SUB)

10

11RG12H113

R7.7/P0

R-5.0/P0.4

C197

Q191

2SC4178-F13F14-T1

BUFFER

R9.2/P0

6

NC(VL)

XX

B

6

DGND

9

GND

R9.2/P0

7

CCD_OUT

VDD

8

ICX227AK-43 NTSC 1/4 CCD TYPE

ICX233AK-43 PAL 1/4 CCD TYPE

IC191

R12.0/P0

R198

1/6 CCD MODEL

100:

1/4 CCD MODEL

0:

C193

XX

C195

0.1u F

C194

XX

ICX096AK-43 NTSC 1/6 CCD TYPE

ICX097AK-43 PAL 1/6 CCD TYPE

B

LND191

CCD IMAGER

CD-281/286

Precautions Upon Replacing CCD imager

• The CD-281/286 board mounted as a repair part is not equipped

16

H

with a CCD imager. When replacing this board, remove the CCD imager from the old one and mount it onto the new one.

• If the CCD imager has been replaced, carry out all the adjustments for the camera section.

• As the CCD imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC. In addition, ensure that the receiver is not covered with dusts nor exposed to strong light.

4-7 4-8

MI-040/041 (STEADY SHOT, MIC AMP, IR DRIVE) PRINTED WIRING BOARD

— Ref. No. MI-040/041 Board; 10,000 Series —

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

For printed wiring board

• Refer to page 4-70 for parts location.

• MI-040/041 board consists of multiple layers. However , only the sides (layers) A and B are shown.

• Chip parts Transistor

C

BE

There are a few cases that the part printed on this diagram isn’t mounted in this model.

CD-286 (TR model) CD-281 (TRV model) (CCD IMAGER)

CONTROL SWITCH BLOCK (CF-1000) (TRV model)

PD-131 (TRV model)

MI-040 (TR model) MI-041 (TRV model) (STEADY SHOT, MIC AMP, IR DRIVE)

RGB, TIMING GENERATOR, BACK LIGHT

4-9 4-10

STEADY SHOT, MIC AMP, IR DRIVE

MI-040/041

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

For Schematic Diagram

• Refer to page 4-9 for printed wiring board.

1

54

62

7

8

9

10

113

12

MI-040 BOARD(1/2)

MI-041 BOARD(1/2)

A

STEADY SHOT,MIC AMP

(TR MODEL) (TRV MODEL)

-REF.NO.:10000 SERIESXX MARK:NO MOUNT

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

B

(REMOTE COMMANDER MODEL)

D752

MA111-(K8)SO.

IC751

REMOTE COMMANDER

RECEIVER

12

D754

*

34

IC751

D755

MA111-(K8).S0

D756

XX

C

IC751 RS-180T

PNA4S13M02SO

D

E

:TR728E/TRV78/TRV78E/TRV98E :TRV49/TRV49E/TRV59E/TRV98

MIC901

CN752

2P

CN751

XX

MA111-(K8).S0

LND751

SEIDEN

1INT_MIC_R

2GND

1INT_MIC_L

2GND

REMOTE COMMANDER MODEL:CCD-TR728E/TRV49/TRV49E/TRV59E/ TRV78/TRV78E/TRV98/TRV98E LASER LINK MODEL :CCD-TRV98

F

STEADY SHOT MODEL :CCD-TR818/TRV68/TRV78/TRV78E/ TRV88/TRV98/TRV98E TRV MODEL :CCD-TRV49/TRV49E/TRV58/TRV59E/ TRV68/TRV78/TRV78E/TRV88/TRV98/ TRV98E TR MODEL :CCD-TR618/TR618E/TR718E/TR728E/TR818

G

SIGNAL PATH

VIDEO SIGNAL

CHROMA

Y

Y/CHROMA

REC

H

PB

I

4.6

4.7

C810

XX

(STEADY SHOT MODEL)

23

SE751

Vref

PITCH

SENSOR

Vcc

1

SENSOR

1

Vcc

Vref 23

C758

6.3V

AUDIO

SIGNAL

SE752

YAW

out

22u

GND

out

C777

C762

22u

6.3V

RB751

C763

0.1u 10V

B

4

C768

0.056u

RB752

4

C772

0.056u

0.056u 25V

25V

B

0.9

0.7

1.3

7

8

9

10

GND

LIA1

LIB1

LIB211LIA2

LO2

13

14

12

25V

0.9

0.7

1.4

C774

0.056u

1.4

C775

25V

6.3V

B

R782

C784

10k

22u

6.3V

1.3

1.31.3

1.3

3

4

HO15HI16LO1

Vref1

Vref2

HI2

HO2

AM2

15

16

17

18

1.3

R1.2/P1.2

22u

IC753

C759

0.1u 10V

B

SENSOR AMP

R780

10k

C808

C770

10u

XX

6.3V

B

C764

0.01u

1005

R757

C761

B

2200

BH7871FV-E2

IC752

XX

B

C776

0.1u B

R766

XX

R769

R767

8200

XX

1.4

BIAS

IN_R

HPF_ON/OFF

IN_L

REG_2.5V

AMP_OUT_L

GND

12345678910

2.4

1.4 1.4

1.4

R761

XX

B

C769

XX

C809

47u

6.3V

R783

1M

R1.4/P1.2

2

AM1

PASS1OUT1

OUT2

CRST

19

20

0

2.8

R779

1M

R784

XX

C787

XX

B

2012

R775

8200

R776

0

R774

18k

1.4

1.40

AMP_OUT_R

MTX_AMP_IN_R

MTX_AMP_IN_L

SUB_SIG_OUT_L

SUB_SIG_OUT_R

1.4

XX

R768

R764

XX

B

R765

R771

C773

XX

R772

XX

R785

15K

C789

0.33u 16V

2012

IC753

*

VCC

C781

0.22u B

C782

0.01u B

C785

0.022u B

C788

1.4

R_OUT

HPF_OUT_R

L_OUT

MTX_AMP_OUT_R

HPF_OUT_L

MTX_AMP_OUT_L

1.2

1.1

1.2

BXX

C786

C783

R789

XX

B

R770

XX

C779

XX

B

C780

XX

B

C791

0.01u 16V

B

R788

33k

0.022u B

11121314151617181920

VCC

XL_CH_SLEEP

0.5

R786

XX

IC753 NJM3230V(TE2) UPC6756GR-8JG-E2

R797 1800

C794

10u

6.3V L751

10uH ±10%

2.8

C796

C800

XX

10u

C799

0.22u B

6.3V

B

IC752

MIC AMP

(LASER LINK MODEL)

:TR818/TRV68/TRV88/TRV98 :TRV78/TRV78E/TRV98E

D753

TLSU1008(T05,SOY)

(TALLY)

24PCN753

XF_TALLY_LED

24

23

MIC_R

REG_GND

22

21

MIC_L

20

SE_GND

19

YAW_AD

18

PITCH_AD

17

VST_C_RESET

16

XSIRCS_SIG

15

XWIND_ON/SIRCS_PWM

A_2.8V

14

13

AU_2.8V

12

A_4.75V

11

IR_ON

10

IR_A_DEV

9

IR_V_DEV

8

IR_CARR

7

IR_L_OUT

6

IR_R_OUT

5

VTR_UNREG

4

IR_VIDEO

3

REG_GND

2

1

IR_FSC

VTR_UNREG

A_4.75V

REG_GND

IR_FSC

IR_VIDEO

IR_R

IR_L

IR_CARR

IR_V_DEV

IR_A_DEV

SIRCS_PWM

IR_ON

TO VC-251 BOARD(11/11) CN703

THROUGH THE FP-263 FLEXIBLE

(

(SEE PAGE 4-63)

TO(2/2)

)

STEADY SHOT, MIC AMP

MI-040/041 (1/2)

16

4-11 4-12

For Schematic Diagram

• Refer to page 4-9 for printed wiring board.

• Refer to page 4-66 for waveforms.

1

2

MI-040 BOARD(2/2) MI-041 BOARD(2/2)

IR DRIVE

A

-REF.NO.:10000 SERIESXX MARK:NO MOUNT

VTR_UNREG

A_4.75V

B

C

D

TO(1/2)

REG_GND

(LASER LINK MODEL)

IR_CARR

IR_V_DEV

IR_A_DEV

IR_VIDEO

IR_L

E

IR_R

F

IR_FSC

SIRCS_PWM

G

16

IR_ON

3

(TR MODEL) (TRV MODEL)

L3906

10uH

R3930

R3901

XX

33k

R3902

4700

R3903

33k

C3907

1u

B

RB3901

R3931

12k

C3905

0.47u

C3906

0.47u

C3901

1608

C3902

TA

B

XX

4V

R3924

1u

B

2012

A

0

NO MARK:REC/PB MODE

R :REC MODE

P :PB MODE

NO MARK:IR ON/IR OFF MODE

( ) :IR ON MODE

[ ] :IR OFF MODE

R3927

2012

R3904

12k

C3909

0.01u B

1005

C3904

0.01u 16V

B

1005

2.4

0.3

0.2

C3903

XX

6.3V A

TA

C3908

1u

R3905

1M

B

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

R3915

560

C3925

0.1u

1005

8

9

10

11

124

SIGNAL PATH

VIDEO SIGNAL

CHROMA

Y

Y/CHROMA

REC

4.7u 16V

(1.2)/ [0]

C3933

1005

0.1u B

R3922

0

(LASER LINK)

Q3903

2SD1664-T1

LED DRIVE

(1.2)/ [0]

R3929

*

1/10W

2012

PB

D3901

CL310IRS

R3925

1/10W

2012

D3903

R3948

(IR)

*

Q3904

*

LED DRIVE

D3902

DCRS815

(LASER LINK)

(5.3)/ [6.4]

(0.6)/ [0]

C3934

*

1005

10V

B

R3926

*

R3917

C3926

0.01u 1005

C3935

XX

470

B

R3916

6800

B

C3932

R3919

1500

Q3901

C3930

0.01u

1005

B

2SA1774HT2

LED DRIVE

(4.5)/ [0]

Q3902

2SA1037AK

LED DRIVE

C3931

0.01u B

1005

R3923

*

R3921

470

(0.6)/ [0]

R3920

470

(3.8)/

[4.5]

C3929

22u 4V TA

A

NIGHT SHOT MODEL :EXCEPT CCD-TRV98 LASER LINK MODEL :CCD-TRV98

R3946

XX

B

TR MODEL :CCD-TR618/TR618E/TR718E/TR728E/TR818 TRV MODEL :CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/ TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

*MARKED:MOUNT TABLE

C3934

D3903

Q3904 XX 2SC4617HT2L

R3923

R3925

R3926

R3927 0

R3929 XX 120

LASER LINK

0.1u

XX

10

18

XX

XX 0R3948

NIGHT-SHOT

XX

CL-310IRSX-TV

470

120

XX

AUDIO

SIGNAL

5

*

L3902 10uH

C3912

10u

6.3V

C3911

0.01u B

1005

C3910

4.7u

6.3V TA

A

3.4

37

CLAMP C1

38

NC

0

39

V DEV ADJ

40

NC

41

V IN

0

42

REG

43

NC

44

REF

45

A DEV ADJ

0

46

Lch IN

0

47

ALC C

0

48

Rch IN

C3914

0.01u B

1005

C3913

510p

CH

R3908

330

R3909

1k

0.7

0

2.7

33

34

35

36

CAR ADJ

CLAMP C2

PRE EM IN

PRE EM OUT

3

BAND SEL2REF R3[ALC OUT Lch]4X‘tal SEL5[ALC OUT Rch]6[OSC OUT]7X’tal IN8A GND9A GND10LPF L11LPF R12OSC VCC

4.6

1

0

R3907

R3945

22k

±0.5%

1608

4.7

30NC31

VCC32VCC

IC3901

IR TRANSMITTER

IC3901

AN2920FHQ-EB

1

0

XX

6

29

R3913

C3915

0.01u B

1005

L3903

5.6u 2520

R3912

V GND

150k

680

28

V GND

C3916

0

27

0

1u

B

C3918

8p

CH

0

26

HPF OUT

2

0

V REF

C3919

0.47u

C3917

0

25

VRF IN

B

713

C3923

C3921

39p

33p

CH

L3905

L3904

33uH

2520

0.1u B

1005

4.7

MIX IN

STBY

CHUP C

R3914

150k

NC

C3922

24

23

0

22

0

21

0

20

19

0

18

17

0

16

0

15

0

14

0

13

C3924

1u

B

DRV CL OUT

DRV EM OUT

DRV SW

MIX OUT

VRF OUT

ARF OUT

4.7

C3920

0.47u B

4-13 4-14

IR DRIVE

MI-040/041 (2/2)

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

PD-131 (RGB, TIMING GENERATOR, BACK LIGHT) PRINTED WIRING BOARD

— Ref. No. PD-131 Board; 10,000 Series —

RGB, TIMING GENERATOR, BACK LIGHT

PD-131

For printed wiring board

• Refer to page 4-70 for parts location.

• PD-131 board consists of multiple layers. Ho wever , only the sides (layers) A and B are shown.

• Chip parts Transistor

C

BE

There are a few cases that the part printed on this diagram isn’t mounted in this model.

4-15 4-16

CD-286 (TR model) CD-281 (TRV model) (CCD IMAGER)

MI-040 (TR model) MI-041 (TRV model) (STEADY SHOT, MIC AMP, IR DRIVE)

CONTROL SWITCH BLOCK (CF-1000) (TRV model)

PD-131 (TRV model) RGB, TIMING GENERATOR, BACK LIGHT

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

4-17 4-18

RGB, TIMING GENERATOR, BACK LIGHT

PD-131

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

For Schematic Diagram

• Refer to page 4-15 for printed wiring board.

• Refer to page 4-66 for waveforms.

1

38

5 13

6

924 7

10

11 1514

12

17 2016 18 19

PD-131 BOARD(1/2)

A

RGB,TIMING GENERATOR

-REF.NO.:10000 SERIESXX MARK:NO MOUNT

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

B

C

TO VC-256 BOARD(11/11) CN701

(SEE PAGE 4-64)

D

E

CONTROL SWITCH BLOCK (PR-10000)

S001

(PANEL REVERSE)

F

CONTROL SWITCH BLOCK(PR-10000) is replaced as a block.

G

So the PRINTED WIRING BOARD is omitted.

H

I

2.5 INCH MODEL :CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/ TRV68/TRV78/TRV78E 3 INCH MODEL :CCD-TRV88

3.5 INCH MODEL :CCD-TRV98/TRV98E TRV MODEL :CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/ TRV68/TRV78/TRV78E/TRV88/TRV98/ TRV98E

J

K

L

CN5701

CN5702

(TRV MODEL)

20P

SE_GND

BL_GND

BL_REG

BL_CONT

PANEL_-15.3V

PANEL_13.3V

PANEL_4.75V

PANEL_2.8V

REG_GND

XVC_SCK

XCS_LCD_DA

VC_SO

PANEL_XVD

C-SYNC/XHD

PANEL_HOLD

PANEL_B

PANEL_G

PANEL_R

AD5

XSYS_RST

6P

PANEL_REV

N.C.

GND

FB5502

0uH

R5505

C5527

0.01u 1005

B

0.7

36

R_INJECT

1.7

35

EXT_DA1

BGP

1.1

2.7

33

34

N.C

BGP

15k

BLK

0.2

31

32

GND3

BLACK_IN

IC5501

LCD DRIVER

IC5501

RB5P003AM1

C5509

3.3u 50V

FRP

COM_FRP

1.4

29

30

FRP

COM_FRP

3

2

1

N.C2N.C3N.C4N.C5N.C6N.C7BIAS8OP_IN+9OP_IN-10OP_OUT11VCO12N.C

R5539

R5534

1

XX

0

2.7

37

BGP

38

SWCOM

0.1

39

SW

1.4

40

FRP

1.4

41

COM_FRP

2.5

42

XSCK

2.8

43

VDD/TESTI

2.8

44

XCS

2.7

45

SO

0.2

46

SI

2.8

47

VSYB

2.8

48

XVD

7

1.4

R5506

2700

R5508

68k

R5507

47k

R5509

22k

2.8

33

34

35

36

SYF

POCB

+IN/TESTO

OUT/TESTO

HDI2HDB3W/H4BL-ON5BL-DET6GND/TESTI7TESTI/GND8LED9PWM10TESTI11TESTI12CPMODE/CLS

1

0.2

2.702.8

XHD_OUT

SYNC

R5521

47k

28

1.4

32

IC5502

TIMING GENERATOR

2.8

L5502

10uH

R5531

180k

DAC

REG_GND

C5501

SE_GND

1

TO(2/2)

BL_GND

BL_REG

BL_CONT

R5523

C5503

0

0.1u B

C5526

R5503

100k

±0.5%

R5524

XX

1005

C5525

XX

1005

0.01u

XVC_SCK

XCS_PANEL

XTG_SO

XVC_SO

XVD

SYNC

HOLD

1005

10u

R5502

4V

XX

TA

C5505 C5506 C5507

XC.SAVE

XVC_SCK

XTG_SO

XCS_PANEL

XP.SAVE

XSYS_RST

C5529

XX

1005

D5501

XX

BGP

BLK

FRP

COM_FRP

1.6

37

EXT_DA2

2.8

38

XC.SAVE

2.5

39

XSCK

2.7

40

SI

2.8

41

R5501

470k

FB5501

OuH

C5502

XX

16V

B

Q5501

XX

R5526

XCS

2.8

42

Vcc1

2.8

43

TRAP_ADJ

1.1

44

LPF_ADJ

2.8

45

XP.SAVE

1.8

46

B_IN

1.9

47

G_IN

1.8

48

R_IN

C5504

0.1u B

1005

R5504

XX

C5508

XVD_OUT

20

19

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

2

3

4

5

6

R5702

10k

XVC_SCK

XCS_PANEL

XVC_SO

XSYS_RST

R5703

XX

L5501

10uH

2520

XVD

SYNC

HOLD

C5510

0.01u B

1005

N.C

C5511

-IN/TESTO

560p

LZ9FF474

6.8

13.6

27

COM_OUT

1.5

3.1

CH

68k

R5510

2.8

31

GND

PS/VDD

IC5502

000

R5511

5

C5512

C5513

C5514

0.1u 22u

B

6.3V

1005

TA

4.7

25

Vcc226Vcc3

6

4

0.1u B

1005

1M

1.4

29PD30

B_DC_DET

G_DC_DET

R_DC_DET

XC.SAVE

2.8

28

XC.SAVE

2.8

2.3

24

L5503

R5513

23

22

21

20

19

18

17

16

15

14

13

1M

R5535

1.7

2.3

1.7

2.3

1.7

4.7

13.6

*

0

XP.SAVE

2.8

25

DR.P.SAVE

2.5

1T369-01-T8A

HCNT/SPD

MCLK/CLD

CLR/CTR

OE/PSS2

SRT/PSS1

VDD/RES

RESET/EX2

STBYB/PSG

GSRT/MODE2

GPCK/MODE1

GRES/EX1

CP/SPS

D5502

C5516

C5517

C5518

100p

0.1u 1608

B

0.1u

1608

B

RB5501

0

R5530

XX

Q5502

MGSF1P02LT1

SWITCH

4.7

C5532

XX

R5533

1M

R5527

100

XX

2.8

C5519

0.1u

B

1608

50V

CH

0.1

24

1.2

23

1.4

22

2.8

21

2.3

20

1.4

19

0

18

2.8

17

2.8

16

2.8

15

2.8

14

2.8

13

R5519

R5518

R5516

10k

C5520

10u

16V

C5522

C5523

0.1u B

1005

C5528

50V

R5514

XX

R5515

0

R5520

XX

1608

0

R5517

XX

C5521

0.1u

1u

B

1005

TG24 TG23

TG22

TG21

TG20

TG19

R5525

XX

D5503

1SS355TE-17

1u

XX

BL_ON

LED

DETIN

TG12

TG18

TG17

TG16

TG15

TG14

TG13

TG24

TG23

TG22

TG21

TG20

TG19

TG18

TG17

TG16

TG15

TG14

TG13

TG12

R5532

100k

2.8

Q5505

SWITCH

DTC144EHT2L

2

TO(2/2)

VB

VG

VR

GND2

GND1

VSH

Vcc4

N.C

R5512

100k

C5515

0.001u SL

1.4

1.3

26

27

OSCI

OSCO

8

0

*MARKED:MOUNT TABLE

L5503

R5522

SIGNAL PATH

REC

PB

4.7

B

RB5502 10K

1u

C5524

-15.6

-15.0

-15.6

S

HN1B04FE-Y/GR(TPLR3)

LCD 2.5 INCH

27uH

±5%

1k

VIDEO SIGNAL

CHROMA Y

13.6

Q5503

S

4.0

S

13.6

Q5504 SWITCH

R5529

XX

R5528

XX

SWITCH

RB5503

HN1B04FE-Y/GR(TPLR3)

LCD 3 INCH LCD 3.5 INCH

6.8uH ±5%

4700 5600

6.8uH

±5%

Y/CHROMA

C5530

0.01u 16V

B

C5531

0.01u 16V

B

XVD_OUT

R5522

SYNC

XHD_OUT

CN5501

24P

24

VSH5V

23

VSH3V

22

GND

21

VB

20

VG

19

VR

18

SPD

17

CLD

16

CTR

15

PSS2

14

PSS1

13

RES

12

CLS

11

VCOM

10

EX2

9

PSG

8

MO2

7

MO1

6

EX1

5

SPS

4

VGLAC

3

VGL

2

GND

1

VGH

CN5502

10P 1VB

2 XVD_OUT

3VG

4 PANEL_COM

5VR

6 PANEL_ID

*

7 C-SYNC/XHD

8 XHD_OUT

9GND

10 GND

LCD901

2.5/3/3.5 INCH LCD COLOR UNIT

(FOR CHECK)

CPC

M

16

RGB, TIMING GENERA TOR

PD-131 (1/2)

4-19 4-20

For Schematic Diagram

• Refer to page 4-15 for printed wiring board.

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

A

B

C

D

1

PD-131 BOARD(2/2)

BACK LIGHT

-REF.NO.:10000 SERIESXX MARK:NO MOUNT

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

BL_REG

BL_GND

PANEL_4.75V

PANEL_2.8V

1

TO(1/2)

(TRV MODEL)

R5608

XX

D5603

XX

38

Note :

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

C5607

4.7u

3216

B

L5601 100uH

IC5602

2.8

45

IC5602

TA75S393F-TE85R

-0.5

C5602

XX

B

BL DET.

VCC

3

R5601

1800

C5603

0.015u

2012

4.6

1

2

4

INVERTER DRIVE

R5602

100k

0.33

123

2.2

B

Q5602

FP216-TL

5

12k

R5603

R5604

1800

-0.5

C5604

0.1u

1005

C5608

XX

B

LED DRIVE

B

5

1

2

3

4

T5601

INVERTER

TRANSFORMER

Q5603

XX

R5606

22k

10

R5605

6

XX

D5601

1SS355TE-17

C5605

0.1u

1005

C5606

12pF

4520

B

ET5601

XX

ET5602

XX

10PCN5601

10 BL_HIGH

9 N.C

SL

D5602

XX

R5611

XX

R5610

0

R5607

470

8 N.C

7 N.C

6 N.C

5 N.C

4 N.C

3 BL_LOW

2 LED

1 LED_GND

ND901

BACK LIGHT

924 7

Note :

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

1056

DAC

SE_GND

BL_CONT

E

2

TO(1/2)

F

TRV MODEL:CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

REG_GND

DETIN

BL_ON

LED

R5609

XX

D5604

XX

RB5601

10K

1.6 2.8

C5601

XX

1005

2.8

TC7W53FU(TE12R)

1

0

2

3

4

Q5601

DTC144EHT2L

SWITCH

COM

INH

VEE

GND

IC5601

VCC

CH0

CH1

8

1.6

7

2.8

6

0

A

5

IC5601

BACK LIGHT BRIGHT SWITCH

LD5605

A

16

4-21 4-22

BACK LIGHT

PD-131 (2/2)

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

)

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

VF-129 (B/W EVF) PRINTED WIRING BOARD

— Ref. No. VF-129 Board; 1,000 Series —

For printed wiring board

• Refer to page 4-71 for parts location.

• VF-129 board consists of multiple layers. Ho wever , only the sides (layers) A and B are shown.

• Chip parts Transistor

C

BE

VC-251 CAMERA PROCESSOR, Y/C PROCESSOR, FOCUS/ZOOM MOTOR DRIVE, REC PB AMP, LINE I/O AMP, SERVO, MODE CONTROL, HI CONTROL, AUDIO, DC/DC CONVERTER

VF-129 (B/W EVF model (B/W EVF)

There are a few cases that the part printed on this diagram isn’t mounted in this model.

B/W EVF

VF-129

4-24

For Schematic Diagram

• Refer to page 4-66 for waveforms.

1

VF-129 BOARD

A

B/W EVF

-REF.NO.:1000 SERIESXX MARK:NO MOUNT

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

B

TO VC-251 BOARD(11/11) CN715

THROUGH THE FFC-256

C

FLAT CABLE

(SEE PAGE 4-64)

D

E

23 11106

5 12

CCD-TR618/TR618E/TR718E/TR728E CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/

TRV78E/TRV88/TRV98/TRV98E

4PCN901

1EVF_4.75V

2EVF_GND

3BW_EVF_Y

4XTALLY_LED

D901

PR1102W-TR

(TALLY)

R903

1.8k

2012

C901

68u

6.3V TA

C

C903

0.47u 25V

TA

A

R910

15k

R907

100k

H DRIVE

R909

1.8

5

6

10k

R908

390k

H OSC

C904

1500p

C905

33u

6.3V TA

B

C913

0.47u 25V TA

A

1.6

2.3

AFC

VIDEO

AMP/MIX

R911

3216

R901

470

R902 470

C902

0.1u F

2012

R905 1200

4.9V DETECTOR

27

4

C906

1u

F

3216

R912

1M

4.3

2.0

910111213141516

SEP

V SYNC

SYNC SEP

Q903

2SA1163G-TE85L

VIDEO AMP

R927

1k

R904

10k

0.4

Q901

2SD1819A-QRS-TX

IC901

VIDEO AMP

R918 4700

1.8

R928

3300

2SD1615-T1GLGK

H OUT

Q902

R906 1500

2SD1819A-QRS-TX

VIDEO DRIVE

4.6

L902 33uH ± 5% 3225

C908

27p

CH

2.3

-11.7

4.4

C909

0.001u B

2012

SOL901

Q904

74

R920

C910

4700p

-12.3

22k

SL

L901

47uH

3225

C911

6800p

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

9

T902

XX

2

1

3

4

5

6

R919

68k

C912

68u

6.3V

SL

TA

C

D903

MA111-(K8).S0

L903

HLC

DUMPER

T901

4

5

6

1 DV1

2 DV2

3 DH1

4 DH2

1

C914

1.5u 35V

4PCN902

-25V

TA

A

F.B.T

7

8

W901

R921

470k

R924

2.7M

BRIGHT

R926

1k

DEFLECTION YOKE

250V

V901

6.8

HV

R925

2.7M

3

2

7

8

C916

0.001u 500V

RV904

R923

1M

R922

270k

C915

0.022u B

2012

1G1

2H

3H

N.C.

4

5G2

2200V

5P

G2

G1

H

PICTURE TUBE (MOIKXX90WB)

138

F

G

H

16

IC901 BA7149F-E2

1

V OUT V OSC

12345678

2.1

4.6

2.0

R915

22k

R914

XX

R913

XX

R930

3.3

TH901

XX

2

R932 4700

R916

XX

± 0.5%

R931

1

RV903

V SIZE

2.1

2.0

1.3

R929

1k

3

C907

0.1u

R917

68k

± 0.5%

470

Note :

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Note :

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

SIGNAL PATH

VIDEO SIGNAL

REC

PB

HV

YCHROMA

Y/CHROMA

4-25 4-26

B/W EVF

VF-129

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

VF-141 (COLOR EVF) PRINTED WIRING BOARD

— Ref. No. VF-141 Board; 10,000 Series —

For printed wiring board

• Refer to page 4-71 for parts location.

• VF-141 board consists of multiple layers. Ho wever , only the sides (layers) A and B are shown.

• Chip parts Transistor

C

BE

There are a few cases that the part printed on this diagram isn’t mounted in this model.

LB-062 (TR818) (EVF BACK LIGHT)

VF-141 (TR818) (COLOR EVF)

CF-077 (TR model) (SWITCH)

COLOR EVF

VF-141

4-27 4-28

For Schematic Diagram

• Refer to page 4-27 for printed wiring board.

• Refer to page 4-67 for waveforms.

1

25

47G9

8

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

10 113 1512

13

146

VF-141 BOARD

RGB DRIVER/TG

A

-REF.NO.:1000 SERIESXX MARK:NO MOUNT

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

B

C

D

E

F

H

I

J

VC-251 BOARD(11/11)

THROUGH THE FP-151 FLEXIBLE

CN708

(SEE PAGE 4-64)

(CCD-TR818 ONLY)

TO

18PCN4501

XCS_EVF_D/A

EVF_2.8V

EVF_R

EVF_G

EVF_B

EVF_XHD

EVF_XVD

EVF_GND

XVC_SCK

XVC_SO

EVF_13.3V

EVF_VG

LED_K

FB4502

0uH

R4513

XX

36

C4526

XX

1.1

R4505

470k

XVC_SCK

XTG_SO

L4501 10uH 2520

C4503

C4501

0.1u

10u

6.3V

TA A

18

17

16

15

14

13

VCO

12

11

10

9

8

7

6

5

4

3

DET

2

1

PWM

XCS_EVF

XVC_SCK

XVC_SO

HDO

XHD

XVD

B

D4501

R4534

0

C4505

R4506

XX

R4544

470k

XX

2SD2216J-QR(K8).SO

C4527

2012

R4535

R4507

150k

R4508

0.1u 100k

B

2.8

0

C4510

0.1u B

Q4504

RESET

XCS_EVF

XX

C4506

XX

XVC_SCK

XCS_EVF

XTG_SO

XVC_SO

XVD

XC_SAVE

XP_SAVE

FB4505

0uH

BGP

BLK

FRP

37

2.8

38

2.5

39

2.6

40

2.8

41

2.8

42

2.8

43

1.1

44

2.8

45

1.7

46

B0.01uC4507

1.7

47

0.01uC4508

B

1.7

48

B0.01uC4509

C4504

0.1u B

R_INJECT

N.C

XC.SAVE

XSCK

SI

XCS

Vcc1

TRAP_ADJ

LPF_ADJ

XP.SAVE

4

B_IN

G_IN

5

R_IN

6

XSH.SAVE2SH_R3SH_G4SH_B5SH_A6N.C7BIAS8OP_IN+9OP_IN-10OP_OUT11VCO12COM_DC

1

2.8

2.7

1.4

2.5

2.8

2.6

0.5

2.8

BGP

0.6

33

34

35

N.C

BGP

EXT_DA

0.9

2.8

0.9

SHR

SHG

SHB

XCLP

37

TST3

38

0

SBLK

39

FRP

40

TST4

41

XSCK

42

VDD

43

XCS

44

SO

45

SI

46

VDO

47

XVD

48

BLK

2.7

0

31

32

PRG

BLACK_IN

IC4501

LCD DRIVER

IC4501

CXA3579R-T4

0.9

SHA

2.8

36

XCLR

FRP

1.4

27VP28

29

30

FRP

PFRP

XVP.SAVE

1.4

1.8

C4512

68k

2700

R4515

R4516

47k

R4518

SHG

SHR

0.9

34

SHG35SHR

0.1u

R4517

CH

C4511

560p

22k

SHA

SHB

2.8

0.9

31

32

SHA33SHB

GND

IC4502

TIMING GENERATOR

IC4502

CXD3501AR-T4

26

P_DC_DET

2

1

2.9

30

B

R4520

TST2

C4514

C4513

3.3u

0.1u

20V

B

TA

A

13.5

25

Vcc2

B_DC_DET

G_DC_DET

R_DC_DET

GND2

GND1

COM_OUT

COM_IN

6.7

R4522 100k

R4521

1M

C4515 1000p

68k

SL

L4504

6.8uH 2520

XC_SAVE

1.4

28

29

RPD

XCSAVE

VREF

Vcc3

2.8

VB

VG

VR

27

1T369-01-T8A

1.3

26

OSCI

7

24

23

22

21

20

19

18

17

16

15

14

13

D4502

OSCO

C4516 120p

1.3

3

C4518

6.8

1.7

C4519

6.8

1u B

1.6

C4520

6.8

B

1.7

13.5

R4523

180k

CH

XP_SAVE

2.8

25

XPSAVE

BLK

HCK1

HCK2

HST

RGT

VDD

DWN/CLR

STB

VCK

VST

TSTEN

EN

20121uB

2012

20121u

C4523

R4526

100

R4527

100

R4528

100

4.7u B

3216

C4524

2.2u F

2012

24

0

23

1.4

22

1.4

21

0

20

2.8

19

2.8

18

2.8

17

2.6

16

2.8

15

1.4

14

0

13

TG24

TG23

TG22

TG21

TG20

TG18

TG17

TG16

TG15

TG14

R4545

33k

R4546

33k

R4547

33k

CN4502

16P

16

COM

15

G

14

R

13

TG24

TG23

TG22

TG21

TG20

TG18

TG17

TG16

TG15

TG14

12

11

10

9

8

7

6

5

4

3

2

1

B

BLK

HCK1

HCK2

HST

RGT

CLR

EN

STB

VCK2

VST

VSS

VVDD(12.0V)

LCD903 COLOR LCD UNIT

HD2HDO3XWRT4CMPO5DETIN6GND7TST08LED9PWM10-IN11+IN12TST1

K

L

XHD

HDO

Q4503

XX

R4542

0

Q4502

XX

1

2.6

0

0.3

0

0.1

2.5

2.1

SIGNAL PATH

R4529

C4521

R4543

XX

10k

R4530

0.1u 100k

B

D4503

MA2S784008S0

D4504

MA2S784008S0

C4517

0.1u B

R4525

R4524

27k

REC

82k

PB

CHROMA

VIDEO SIGNAL

Y

Y/CHROMA

16

COLOR EVF

4-29 4-30

VF-141

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

LB-062 (EVF BACK LIGHT) PRINTED WIRING BOARD

— Ref. No. LB-062 Board; 10,000 Series —

For Schematic Diagram

• Refer to page 4-67 for waveform.

1

LB-062 BOARD

BACK LIGHT(EVF)

A

-REF.NO.:10000 SERIESXX MARK:NO MOUNT

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

B

C

VC-251 BOARD(11/11)

THROUGH THE FP-151 FLEXIBLE

(SEE PAGE4-64)

TO

VF-141 BOARD

CN4501 THROUGH THE FP-151 FLEXIBLE

(SEE PAGE4-30)

CN708

(CCD-TR818 ONLY)

TO

CN4601

D

16

IC4601

BUFFER

6P

EVF_BL_GND

EVF_BL_4.75V

XTALLY_LED

LED_K

PWM

47

R4603

D4602

R4604

4.7

470k

1

2

3

4

DET

5

6

D4601

XX

Note :

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

XX

IC4601

TC7SET08FU(TE85R)

VCC

123

R4602

XX

4.7

45

1

L4601

47uH 3225

Q4601

FX216-TL1

INVERTER DRIVE

0.30.2 0.3 4.7

C4604

0.1u B

C4601

33u

10V

B

TA

Note :

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

63258

T4601 INVERTER TRANSFORMER

R4601

1

L4602 10uH

2520

2

C4603 2200p

3

B

3216

4

5

C4602

4.7u B

2012

82

10

ND4601

LND601

A

LND602

A

BACK LIGHT

6

For printed wiring board

• Refer to page 4-71 for parts location.

• LB-062 board consists of multiple layers. Ho wever , only the sides (layers) A and B are shown.

There are a few cases that the part printed on this diagram isn’t mounted in this model.

LB-062 (TR818) (EVF BACK LIGHT)

VF-141 (TR818) (COLOR EVF)

CF-077 (TR model) (SWITCH)

EVF BACK LIGHT

LB-062

4-324-31

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

A

B

TO VC-251 BOARD(8/11) CN709

(THROUGH THE FFC-295 FLAT CABLE)

(SEE PAGE 4-58)

C

D

E

1

CONTROL SWITCH BLOCK(CF-1000)

SWITCH,INDICATOR DRIVE

XX MARK:NO MOUNT

CN001

24P

KEY_AD2

24

KEY_AD3

23

KEY_AD4

22

BL_GND

21

LCD_LED_ON

20

LI_3V

19

DIAL_A

18

DIAL_B

17

VTR_UNREG

16

D_2.8V

15

EVER_3.0V

REG_GND

OSD_SO

XOSD_SCK

XHI_RESET

HP_L_OUT

HP_JACK_IN

HP_R_OUT

14

13

SP+

12

SP-

11

10

XCS_LCD

9

COM/XD

8

OSD_SO

7

XOSD_SCK

6

5

4

3

2

1

XCHARGE_LED_ON

XCS_LCD_DRIVER

LCD_COM/XDATA

HEADPHONE_GND

38

(TRV MODEL)

R005

150

XX

D005

D006

5 136

1

2

3

4

5

6

7

8

9

10

11

12

BT001

(LITHIUM BATTERY)

XX

D007

1

2

KEY_AD2

KEY_AD3

KEY_AD4

DIAL_A

OPEN/CLOSE SW

DIAL_B

D_2.8V

EVER_3.0V

XCHARGE_LED_ON

REG_GND

XHI_RESET

OPEN/CLOSE SW

REG_GND

CN006

R004

R003

12PCN005

S001

RESET

S902

OPEN/CLOSE

2P

R002

10k

D001

TLAU1008(T05,SONY)

S002

MENU

S003 TIME

R006

1200

R007 1200

R008 1200

924 7

S004

EXPOSURE

S005 DATE

S006

XX

10

S007

SEL/PUSH EXEC

SELECT_DIAL

R010 1500

R011 1500

R012

END SEARCH

1500

11 1514

R013 2200

R014

2200

R015

2200

TITLE

S012S009

DISPLAY

12

S010

R016 3900

R017 3900

R018

3900

S013

VOLUME+

S015

XX

R019 8200

R020

8200

R021 8200

S016

VOLUME- BACK LIGHT

S017

COUTER RESET

S022

FADER

R022

27k

R023

27k

R024

FOCUS

27k

S018

S019

1716

CH GND

LND002

CH GND

LND003

R052

Q002

2SA1576A-T106-R

SWITCH

R029

F

G

L004

100uH

J001

SP901

SPEAKER

(HEADPHONES)

R001

0

LND001

SEIDEN

2P

CN003

TRV MODEL:CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/

1SP(+)

2SP(-)

TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

H

I

J

SIGNAL PATH

AUDIO

K

SIGNAL

REC

L003

0uH

C008

0.001u

VDR002

B

SEG14

SEG13

SEG12

SEG11

25

COM3

COM4

SEG1126SEG1227SEG1328SEG1429SEG1530SEG1631SEG1732SEG18

SEG10

24

SEG9

23

SEG8

22

SEG7

21

SEG6

20

SEG5

19

SEG4

18

SEG3

17

D002

XX

XOSD_SCK

OSD_SO

XCS_LCD

COM/XD

R009

680k

C001

0.1u B

1

OSC1

2

OSC2

3

VSS

4

VC

5

VLCD

6

VDD

7

SCK

8

SD

IC001

LCD DRIVE

IC001

BU9735K-E2

XCS10C/XD11COM112COM213COM314COM415SEG116SEG2

9

COM1

COM2

VDR001

C007

XX

B

R030

390

Q003

2SD1819A-QRS-TX

SWITCH

R031

0

R032

100k

SEG10

SEG9

SEG8

SEG7

SEG6

SEG5

SEG4

SEG3

33

R033

R034

0

VCC

C002

C003

XX

560

XX

B

10u 10V

L002

CIL

IC003 MIP806

12345

D004

MA1010000LS0

COM1

COM2 SEG3

SEG4

SEG5 SEG6

SEG7 SEG8

SEG9 SEG10 SEG11

SEG12 SEG13

SEG14

COM4 COM3

CONTROL SWITCH BLOCK(CF-1000) is replaced as a block. So the PRINTED WIRING BOARD is omitted.

GND

ENB

(8-759-694-14)

DC

GND

C004 4700p 200V

R026 180k

678910

RT1

RT2

IC003

EL DRIVE

EL

_EL

R027

0

1

2

3

4

5

6

7

8

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

-EL

EL

COM1

COM2

SEG3

SEG4

SEG5

SEG6

SEG7

SEG8

SEG9

SEG10

SEG11

SEG12

SEG13

SEG14

COM4

COM3

CN004 8P

CN003

D901 EL

16P

LCD902

CHARACTER DISPLAY

PB

16

4-33 4-34

CONTROL SWITCH BLOCK

CF-1000

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

CF-077 (SWITCH) PRINTED WIRING BOARD

— Ref. No. CF-077 Board; 1,000 Series —

SWITCH

CF-077

For printed wiring board

• Refer to page 4-71 for parts location.

• CF-077 board consists of multiple layers. Ho wever , only the sides (layers) A and B are shown.

There are a few cases that the part printed on this diagram isn’t mounted in this model.

LB-062 (TR818) (EVF BACK LIGHT)

VF-141 (TR818) (COLOR EVF)

CF-077 (TR model) (SWITCH)

4-35 4-36

For Schematic Diagram

• Refer to page 4-67 for waveform.

1

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

38

56

924 7

10

11

CF-077 BOARD

SWITCH,INDICATOR DRIVE

-REF.NO.:1000 SERIES-

A

XX MARK:NO MOUNT

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

B

TO VC-251 BOARD(8/11) CN709

C

THROUGH THE FFC-295 FLAT CABLE

(SEE PAGE 4-58)

D

(CCD-TR618/TR618E/TR718/TR718E/TR818)

24PCN001

24

KEY_AD2

23

KEY_AD3

22

KEY_AD4

21

BL_GND

LI_3V

DIAL_A

DIAL_B

D_2.8V

BEEP

REG_GND

OSD_SO

20

19

18

17

16

15

14

13

12

11

SP-

10

9

8

7

6

5

4

3

2

1

LCD_LED_ON

VTR_UNREG

EVER_3.0V

XCHARGE_LED_ON

XCS_LCD_DRIVER

LCD_COM/XDATA

XOSD_SCK

XHI_RESET

HP_L_OUT

HP_JACK_IN

HP_R_OUT

HEADPHONE_GND

XCS_LCD

COM/XD

OSD_SO

XOSD_SCK

RB001

10k ×4

BT001

(LITHIUM BATTERY)

S001

RESET

S002

R005 1200

R006 1200

EXPOSURE BACK LIGHTMENU

S005

DATE

S004

R011 1500

S006

SEL/PUSH EXEC

R014

3900

R013 2200

S007

TITLE

R016

12k

R017

39k

S008

COUNTER RESET

S009

E

LND002

CH GND

LND001

CH GND

D003

D004

D005

XX

BZ001

S003

TIME

R015 2200

R023

15k

F

SEG11

SEG12

SEG13

SEG14

SEG15

SEG16

SEG17

SEG18

1.5

26

27

28

29

30

31

32

G

R010

680k

C001

D002

0.1u

XX

B

1005

H

XOSD_SCK

OSD_SO

I

XCS_LCD

16

COM/XD

1.5

1

OSC1

1.5

2

OSC2

VSS

VC

VLCD

VDD

SCK

SD

1

9

2.901.5

3

4

3.0

5

6

2.8

7

2.7

8

SEG18

XCS

SEG17

C/XD

10

SEG15

SEG16

IC001

LCD DRIVE

IC001

BU9735K-E2

COM112COM213COM314COM4

11

1.5

COM2

COM3

COM1

SEG14

1.5

COM4

SEG13

SEG12

SEG116SEG2

15

1.5

SEG1

25

1.5

SEG2

SEG11

SEG10

SEG9

SEG8

SEG7

SEG6

SEG5

SEG4

SEG3

SEG10

1.5

24

SEG9

1.5

23

SEG8

1.5

22

SEG7

1.5

21

SEG6

1.5

20

SEG5

1.5

19

SEG4

1.5

18

SEG3

1.5

17

COM1

COM2

SEG2

SEG3

SEG4

SEG5

SEG6

SEG7

SEG8

SEG9

SEG10

SEG11

SEG12

SEG13

SEG14

SEG1

SEG16

SEG15

SEG18

SEG17

COM4

COM3

S011

FADER

26PCN002

26

BL_VDD

25

BL_GND

24

COM1

23

COM2

22

SEG2

21

SEG3

20

SEG4

19

SEG5

18

SEG6

17

SEG7

16

SEG8

15

SEG9

14

SEG10

13

SEG11

12

SEG12

11

SEG13

10

SEG14

9

SEG1

8

SEG16

7

SEG15

6

SEG18

5

SEG17

4

COM4

3

COM3

2

BL_VDD

1

BL_GND

R018

27k

S010

FOCUS

LCD902

CHARACTER

DISPLAY

4-37 4-38

SWITCH

CF-077

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

)

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

VC-251 (CAMERA PROCESSOR, Y/C PROCESSOR, FOCUS/ZOOM MOTOR DRIVE, REC/PB AMP, LINE I/O AMP, SERV O,

MODE CONTROL, HI CONTROL, AUDIO, DC/DC CONVERTER, CONNECTOR) PRINTED WIRING BOARD

— Ref. No. VC-251 Board; 10,000 Series —

For printed wiring board

• Refer to pages 4-72,4-73 for parts location.

• VC-251 board consists of multiple layers. However , only the sides (la yers) A and B are shown.

• Chip parts Transistor Diode

C

BE

3

21321

There are a few cases that the part printed on this diagram isn’t mounted in this model.

VC-251 CAMERA PROCESSOR, Y/C PROCESSOR, FOCUS/ZOOM MOTOR DRIVE, REC PB AMP, LINE I/O AMP, SERVO, MODE CONTROL, HI CONTROL, AUDIO, DC/DC CONVERTER

VF-129 (B/W EVF model (B/W EVF)

CAMERA, VIDEO, AUDIO, SERVO, MODE/HI CONTROL, D-D CON

VC-251

4-40

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

4-41

CAMERA, VIDEO, AUDIO, SERVO, MODE/HI CONTROL, D-D CON

VC-251

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

For Schematic Diagram

• Refer to page 4-39 for printed wiring board.

• Refer to page 4-68 for waveforms.

1

VC-251 BOARD(1/11)

CAMERA PROCESSOR AMP(CH BLOCK)

A

-REF.NO.: 10000 SERIESXX MARK:NO MOUNT

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

B

CN271

14P

C

D

TO CD-281/286 BOARD CN191

THROUGH THE FP-259 FLEXIBLE

(SEE PAGE 4-8)

GND

CAM_-7.0V

VSHT

CAM_15V

GND

CCD OUT

E

SIGNAL PATH

F

REC

PB

PAL MODEL :CCD-TR618E/TR718E/TR728E/

G

TRV49E/TRV58E/TRV59E/ TRV78E/TRV98E NTSC MODEL :CCD-TR618/TR818/TRV49/TRV58/ TRV68/TRV78/TRV88/TRV98 1/4 CCD MODEL :CCD-TR818/TRV68/TRV78/ TRV88/TRV98/TRV98E 1/6 CCD MODEL :CCD-TR618/TR618E/TR718E/ TR728E/TRV49/TRV49E/

H

TRV58/TRV58E/TRV59E

CHROMA

VIDEO SIGNAL

Y

Y/CHROMA

I

J

16

38

1/6 CCD MODEL

VSHT

V4

V3

V2

V1

D271

MA111-(K8)

R271

100k

CH

22p

C271

V4

1

V3

2

V2

3

V1

4

5

RG

6

H1

7

H2

8

9

10

11

12

13

14

R274

100k

C273

11

:NTSC MODEL :PAL MODEL

VC_SI

CH_SO

XCH_SCK

XCS_CH

AD10

AD9

AD8

AD7

AD6 AD5

AD4

AD3 AD2

AD1 V_STOP

PBLK

ID

XSG1

XV1

AVD

AHD

CLP1

ADCK

MCK

CL

CK_CONT1

CK_CONT2 XCS_KINUTA

XRST_KINUTA

SYS_V

PB_C_RF

LINE_Y

CAM_15V

A_4.75V

CAM_-7.0V

D_2.8V

A_2.8V

REG_GND

FRQ_TUNE

CAM_DD_ON

VC_SO

XVC_SCK

VC_SI

CH_SO

XCH_SCK

XCS_CH

AD10

AD9

AD8

AD7

AD6

AD5

AD4

AD3

AD2

AD1

V_STOP

PBLK

ID

XSG1

XV1

AVD

AHD

CLP1

ADCK

MCK

CL

CK_CONT1

CK_CONT2

XCS_KINUTA

XRST_KINUTA

SYS_V

PB_C_RF

LINE_Y

12

36

1

2

3

4

5

6 7 8

TO(10/11)

TO(9/11)

TO(8/11)

TO(7/11)

TO(2/11)

TO(2/11,7/11)

TO(7/11,8/11)

TO(4/11)

TO(5/11)

L271

10uH

RB272 47KX4

10

ADCK

PBLK

CK_CONT1

CK_CONT2

AHD

XRST_KINUTA

XCS_KINUTA

V_STOP

VC_SI

XSG1

CLP1

XCH_SCK

CH_SO

XCS_CH

SYS_V

PB_C_RF

LINE_Y

X271

28.636363MHz

28.375MHz

ID

AVD

XV1

5 136

CL

MCK

FB273

10uH

C277

0.01u 1005

R275

L272

B

2.8

0

R2.3/P0

1/4 CCD MODEL

0

R0.4/P0

2.8

R1.5/P0

R1.3/P0

C278

4.7u 20V

HS102 1608

FB275 1005 B

C281

0.1u

C280

0.1u B

1005

C279

10u

6.3V

FB271

0uH

C274

10u

6.3V

XSHP

C275

XSHD

0.01u B

1005

C272

0.001u B

1005

22p

CH

C276

0.22u

B

XSHP

XSHD

RB273

100

VDD2

13

VSS3

14

XSHP

15

XSHD

16

XRS

17

RG

18

VDD3

19

VDD4

20

H1

21

H2

22

VSS4

23

NC

24

2.8

1.5

2.8

R2.2/P0

2.7

R2.1/P0

R2.3/P0

R2.8/P0

2.8

0uH

1.50R2.8/P0

12

VICK(CL)

R279

FB276

XX

0uH

FB274

C282

0.001u B

R0/P1.4

9

10

11

TEST

VDD1

CHCK

SYSCK

21

IC271

TIMING GENERATOR

CXD2444R-T4

3

45

R12.0/P0

V2

26V127VH28V329VL30VM31V432NC33

25

R-0.2/P0

R-4.7/P0

V2

V1

V3

AD9

AD8

AD10

R0.1/P1.5

R0.6/P1.3

R1.2/P1.3

12

DVSS

DRVDD

13

DRVSS

14

15

16

17

18

19

20

21

22

23

24

DVSS ADCLK

DVDD

PBLK CLPOB

XSHP XSHD

CLPDM

AVDD

AVSS

25

26

27

C286

1u

B

1608

S/H AGC A/D CONVERTER

6

CLPOUT

AVDD

28

2.8

R1.1/P0

D272

1SV329(TPL3)

C285

C283

0.001u

8p

B

CH

1608

1.4

0.1u B

2012

1M

AD6

R1.2/P1.5

1.3

XSHT34XSG1

0

VSHT

AD5

R1.0/P1.4

R2.8/P0

AD4

R1.1/P1.4

1005

R2.2/P0

35

0.3

AD3

2

PBLK3VSS14OSCI5OSCO6VSS2

SSO

AD2

R1.0/P1.3

R2.8/P0

1

CLPDM

VGAT

36

0

AD1

R1.1/P1.4

1D02D13D24D35D46D57D68D79D810D911

1005

X271

1.2

7CK8

IC271

R-0.7/P0

AD7

R1.0/P1.4

*

C284

R-4.7/P0

R280

V4

IC272

AD80013AJSTRL

LatchSelect

78

29

R0.8/P0.4

C287

1u

B

CLPREF

30NC31

R1.3/P0

CCD IN

C289

0.1u

C288

0.1u

1005

LINE

CLPBYP

AVSS

AVDD

32

33

34

35

2.8

C290

36

0

R0/P0.4

B

1u

C291

0.1u B

1005

0

0.5

B

R281 470k

CKCONT1

CKCONT2

VDD6

DSGAT

TEST

XSCK

SYSV

HDRST

AVSS

CMLEVEL

CHROMA

AVDD

VRB VRT

R1.5/P0

ID

48

R2.8/P0

47

R0/P2.8

46

R2.8/P0

AVD

45

R2.5/P2.8

AHD

44

2.8

43

R2.9/P0

42

R0.1/P0

XV1

41

2.8

RST

40

R2.2/P2.1

SEN

39

R0.4/P0.2

SSI

38

2.6

SSK

37

2.8

48

0

SI

47

2.8

XCE

46

2.5

45

44

2.8

43

42

41

2.8

40

0.9

39

1.9

38

1.4

37

C296

0.1u

1005

C293 470p

B

C292

0.22u B

924 7

C297

22u

4V

XRST_KINUTA

A

TA

C294

1u

B

C295

1u

B

CAMERA PROCESSOR AMP

VC-251 (1/11)

4-43 4-44

For Schematic Diagram

• Refer to page 4-39 for printed wiring board.

• Refer to page 4-68 for waveforms.

1

VC-251 BOARD(2/11)

Y/C PROCESSOR (CL BLOCK)

-REF.NO.:10000 SERIES-

A

XX MARK:NO MOUNT

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

38

37

TO(10/11)

REG_GND

B

TO(2/11)

TO(4/11)

TO(11/11)

TO(7/11)

KINUTA_C_OUT

KINUTA_Y_OUT

AFC_F0_ADJ

XVC_SCK

PB_C_RF

RF_AGC_OUT

REC_RF

PANEL_R

PANEL_G

PANEL_B

PANEL_XVD

PANEL_XHD

PANEL_SYNC

EVF_G/BW_Y

LCD_HOLD

XVC_SCK

MECHA_HD

JOG_VD

MECHA_VD

MECHA_FLD

ATF_SAMPLE

XSG_V_RST

X1/2_SWP

SWP_DIR

TBC_VD

XTBC_V_RST

AFC_F0

XRST_KINUTA

CK_CONT2

XCS_KINUTA

CK_CONT1

VC_SI

VC_SO

DOP

EVF_R

EVF_B

VC_SO

VC_SI

SYS_V

VIVDO

Q156 2SA1774HT2 2SB1462J-Q XX

FSC

:TR MODEL(EXCEPT:TR818) :TRV MODEL :CCD-TR818

VC_SO

XVC_SCK

PANEL_XVD

PANEL_XHD

PANEL_SYNC

LCD_HOLD

XVC_SCK

VC_SO

MECHA_HD

JOG_VD

MECHA_VD

MECHA_FLD

ATF_SAMPLE

XSG_V_RST

X1/2_SWP

SWP_DIR

SYS_V

XRST_KINUTA

CK_CONT2

XCS_KINUTA

9

TO(5/11)

10

C

11

D

12

E

F

13

G

5

TO(1/11,7/11)

H

I

*MARKED:MOUNT TABLE

TR TRV

J

K

L

M

C164

Q165 XX 0.1u

Q166 XX 0.1u

Q153 XX 2SB1462J-Q Q158

R156

R157

R181 XX 12k

R182

R183

R184 XX 12k

R185 XX 12k

R186

*MARKED:MOUNT TABLE

R160

R165

R166

R167

R187

R189

R190

R191

XX

2SA1774HT2

XX

XX 270

XX

B/W EVF

2200

XX

10K

XX

0.1u

2SB1462J-Q

2.2k

2200

270

COLOR EVF

XX

0

270

12K

270470

270

N

16

5 13

CL224 D_2.8V

D_1.5V

A_2.8V

A_4.75V

VC_SI

FSC

FB152

FB153

10uH

L152

10uH

L154

FB154

10uH

L151

CL225

10uH

L155

AFC_F0_ADJ

C151

1u

B

TR MODEL :CCD-TR618/TR618E/TR718E/TR728E/TR818 TRV MODEL :CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E B/W EVF MODEL :EXCEPT TR818 COLOR EVF MODEL:CCD-TR818

C152

4.7u B

3216

BUFFER

R154

10k

RB151

10k

C155

0.1u

B

1005

Q158

Q156

BUFFER

*

BUFFER

6

C184

0.1u 1005

C154

0.1u B

1005

R204 2200

R177

12k

0.1u

0.8

C163

0.1u R180

B

1005

*

C176

R181

C164

* B

R182

1005

C165

B

*

1005

R185

C166

B

*

1005

R186

*

C167

0.1u B

1005

R189

*

C168

0.1u B

1005

R191

*

C169

0.1u

R192

B

1005

0.1u

C171

0.1u B

1005

C172

0.1u 1005 C201

C161

0.01u B

1005 C173

0.01u

B

1005

R174

R169 1k

C158

4.7u

6.3V

R170 6800

R168 5600

R172

100

P2.0

R3.7/

R3.1/P1.4

R175 3300

Q151

HN1B04FE-Y/GR(TPLR3)

VCO

470R178

220R179

5600

1u

*

R183

*

R184

*

R187

*

R188

12k

*

R190

*

12k

C170

B

1005

C177

B

0.01u 1005

XX

R176

C174

0.47u B

TA

R195

15k

0.2

R156

*

R162

XX

Q512

XX

R163

R157

XX

*

Q153

*

R158

R164

*

XX

Q154

XX

R165

R159

XX

Q154

XX

R160

R166

*

R167

R161

XX

Q157

XX

C160

0.1u B

1005

C157

0.1u B

1005

C156

R171

390p

470

CH

R155 1200

R3.0

/P1.4

C162

B

*

B

820

R3.7/P2.0

B

1005

8200

R173

JDV3C11(TPH3)

2.8

1

VDDAA8

0.4

2

REXT8

1.9

3

CBU8

0.3

4

DAO8

5

VSSAA8

6

R0.4

VSSAA7

/P0

7

DAO7

R1.6/P2.8

8

CBU7

R0.6/P0

9

REXT7

2.8

10

VDDAA7

2.8

11

VDDAA6

0.7

12

REXT6

1.8

13

CBU6

0.2

14

DAO6

15

VSSAA6

16

VSSAA5

0.2

17

DAO5

1.8

18

CBU5

0.7

19

REXT5

2.8

20

VDDAA5

2.8

21

VDDAA4

0.7

22

REXT4

1.8

23

CBU4

0.2

24

DAO4

25

VSSAA4

26

VSSAA3

R1.7/P1.8

27

DAO3

1.8

28

CBU3

0.7

29

REXT3

2.8

30

VDDAA3

2.8

31

VDDAA2

0

32

REXT2

2.8

33

CBU2

0

34

DAO2

35

VSSAA2

36

VSSAA1

1.7

37

DAO1

1.8

38

CBU1

0.7

39

REXT1

2.8

40

VDDAA1

2.8

41

VDDAA0

R0/P0.8

42

VRBAD

R0/P2.0

43

VRTAD

R0/P1.4

44

VINNAD

R0/P1.4

45

AD_IN

R0/P1.1

46

OP_OUT

47

VSSAA0

0

48

C_IN

R0/P1.1

49

ATF_IN

R0/P1.4

50

VREFOP

R0/P1.1

51

Y_RF_IN

2.8

52

AVDD

R3.1/P1.4

53

AMPO

R2.8/P1.4

54

R193

INN

1M

39k

D151

C178 1500p

B

R196

15k

C179

XX

D152

JDV3C11(TPH3)

B

R197

12k

R198 470

2.8

0.4

1.9

0.3

211

212

213

214

215

216

DAO9

CBU9

REXT9

VDDAA9

TESTDAC

C_OUT

Y_OUT EVF_G

9

10

11

PANEL_R PANEL_B EVF_B

12

13

14

15

16

17

8bit A/DEVF_RPANEL_GRF

18

19

SCAN_PATH

INP

AVSS

MUTE

WRHLD

55

56

57

58

59

0

R2.8/P1.4

C175

1u

B

C182

0.01u

L156

B

3.3uH

1005

C186

C183

0.1u

XX

B

1005

LCD_HOLD

924 7

C185

1u B

208

209

210

PAVSSB

PDVSSB

VSSA9

PLLB PLLC

(GUM) (Dig8)

PLLA

PAVDDA

DVSS1

PDVDDA

60

61

62

63

2.8

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

10

C189

C190

1u

XX

B

4V

1.4

2.8

204

205

206

207

PAVDDC

PDVDDC

PDVDDB

PAVDDB

2.8

R1.5/P1.4

198

199

200

201

202

203

PDVSSC

PAVSSC

IN_VSS3

XTALOUT

CCDCKL

IN_VDD3

XTALIN

20

IN_VSS1

OSCI

PAVSSA

PDVSSA

OSCO

64

65

66

67

R0/P1.5

R0/P1.40R0/P1.4

C188

C187

0.1u

0.1u B

B

1005

68

IN_VDD1

PDET2

PDET3

PDET1

AFCC

DVDD1

69

70

71

72

73

1.4

R3.1/P1.4

R2.8/P1.4

11 1514

AD7

AD6

AD5

AD4

AD3

AD2

AD1

R1.1/P1.4

R1.1/P1.3

R1.1/P1.4

R1.0/P1.4

R0.8/P1.5

R1.5/P1.4

190

191

192

193

194

195

196

197

ADIN6

ADIN5

ADIN4

ADIN3

ADIN2

ADIN1

ADIN0

PLLENB

AD8

R0.5/P1.3

189

ADIN7

AD9

R0.4/P1.3

188

ADIN8

AD10

R0.1/P1.4

187

ADIN9

R1.4/P1.4

186

DVDD5

ADCK

R1.5/P1.4

185

ADCK

12

184

CLP1

OSD_L_ON

2.70001.4

181

182

183

CLP1

DVSS11

OSD_L_ON

OSD_R_ON

180

OSD_R_ON

CGCK

OSD_P_ON

179

OSD_P_ON

2.80000

178

CGCK

IC151

CAMERA Y/C PROCESSOR

VTR Y/C PROCESSOR

AFT,FOCUS/ZOOM MOTOR CONTROL

IC151

HG75C012SFL

21

22

PANELVD

74

2.8

PANEL_XVD

PANELHD

75

76

2.6

0.201.4

PANEL_SYNC

PANEL_XHD

PANELSYNC

77

DOP

R199

78

1k

TRAPCONT

OUT_VDD1

OFSC

79

80

R200

10k

FSC

JVDI

DVSS2

MCK

HSWP

81

82

83

84

R1.3/P1.40R0.1/P1.2

CL223

JOG_VD

X1/2_SWP

R216

68

SWP

85

1.4

SWP_DIR

XSGRST

86

87

2.8

R0/P0.5

XSG_V_RST

ATSMPL

ATF_SAMPLE

88

2.5

SYS_V

SYSV

89

MECHAFLD

90

1.4

R206

XX

MECHA_FLD

IN_VDD2

91

0

IN_VSS2

BCK

92

93

R0/P0.2

COLOR4

177

IO_VDD5

CSYNC

94

0

MECHA_HD

MECHA_VD

COLOR4

MECHAVD

COLOR3

175

176

COLOR3

XSCK

95SO96SI97

2.5

CL226

XVC_SCK

COLOR2

0.3

CL227

VC_SI

COLOR2

COLOR1

174

COLOR1

R0.3/P0.2

CL228

VC_SO

173

98

CL229

DVSS10

2.1

XCS_KINUTA

ID

XV1

AVD

PBLK

AHD

XSG1

V_STOP

CL221

CL222

R2.3/P0

R1.4/P0

R2.7/P2.8

R2.5/P0

R0.1/P00R2.8/P0

1.5

1.4

163

164

165

166

167

168

169

170ID171

172

DVDD4

VCK

DVSS9

XSG1

VGAT

XV1

AHD

AVD

PBLK

2.8

SENS1

162

2.8

SENS0

161

TEST

160

R1.4/P0

IRIS

159

2.8

TBCVD

158

0

XTECVRST

157

TESTBS

156

VCKO

155

DVSS8

154

0

EN1

153

R2.4/P0

DIR1B

152

R2.4/P0

DIR1A

151

R0.1/P0

DIR0A

150

R1.9/P0

DIR0B

149

R0/P0

EN0

148

2.8

IO_VDD4

147

2.6

VIHDO

146

MEMHDI

145

2.8

VIVDO

144

MEMVDI

143

VIFLDO

142

MEMFLDI

141

DVSS7

140

YMO0

139

YMI0

138

YMO1

137

YMI1

136

1.4

DVDD3

135

YMO2

134

YMI2

133

YMO3

132

YMI3

131

DVSS6

130

YMO4

129

YMI4

128

YMO5

127

YMI5

126

2.8

IO_VDD3

125

YMO6

124

YMI6

123

YMO7

122

YMI7

121

DVSS5

120

CMO3

119

CMI3

118

CMO2

117

CMI2

116

1.4

DVDD2

115

CMO1

114

CMI1

113

CMO0

112

CMI0

111

EOR_OUT

110

TESTKP

109

FECKIN

FECKOUT

DVSS3

IO_VDD2

DVSS4

XFEON

MCKCONT

100

R0/P2.8

CK_CONT2

ADCKCONT

101

2.8

RAMTEST

102

103

104

105

106

107

108

C192

XX B

1005

2.8

C194

XX

B

XRST

XCS

99

2.8

0R208

XRST_KINUTA

SIGNAL PATH

REC

PB

17 2016 18 19

ZM_RST

FC_RST

IRIS_COM

DIR1B

DIR1A

DIR0A

DIR0B

VIVDO

EN1

EN0

VIHD

AD1

AD2

AD3

AD4

AD5

AD6

AD7

AD8

AD9

AD10

V_STOP

PBLK

ID

XSG1

XV1

AVD

0.1u BC195

AHD

CLP1

ADCK

IRIS_COM

EN1

DIR1B

DIR1A

EN0

DIR0B

DIR0A

ZM_RST

FC_RST

XOSD_SCK

XCS_OSD

OSD_SO

XSYS_RST

C196

XX

B

CGCK

XSYS_RST

XCS_OSD

XOSD_SCK

OSD_SO

SIGNAL PATH

Ref.signal

VIDEO SIGNAL

CHROMA

Y Y/CHROMA

IC153

CHARACTER GENERATOR

IC153

MB90099PFV-G-108-BND-ER

2.9

12345678910

CLK

2.8

XCS

2.8

DATA

2.8

XPCL

3.0

VDD

CMDCT

OSC

1.4

OSC

TEST

GND

XHSYNC

XVSYNC

AD1

AD2

AD3

AD4

AD5

AD6

AD7

AD8

AD9

AD10 V_STOP

PBLK

XSG1 XV1 AVD AHD

CLP1

ADCK

MCK

2.6

2.8

0

COLOR1

VC0

0

COLOR2

VC1

0

COLOR3

VC2

0

OSD_P_ON

BLKA

0

COLOR4

VC3

0

OSD_R_ON

BLKB

NC

0

OSD_L_ON

BLKC

11 12 13 14 15 16 17 18 19 20

XSYS_RST

XCS_OSD

XOSD_SCK

OSD_SO

EVER_3.0V

ID

CL

IRIS_COM

EN1

DIR1B

DIR1A

EN0

DIR0B

DIR0A

ZM_RST

FC_RST

VIVDO

4

TO(1/11)

14

TO(3/11)

VIHD

15

TO(7/11,8/11,11/11)

16

TO(8/11)

REC PBREC/PB

4-45

4-46

Y/C PROCESSOR

VC-251 (2/11)

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

For Schematic Diagram

• Refer to page 4-39 for printed wiring board.

1

VC-251 BOARD(3/11)

FOCUS/ZOOM MOTOR DRIVE(LD BLOCK)

A

-REF.NO.:10000 SERIESXX MARK:NO MOUNT

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

38

56

R313 2200

C309

0.22u

C307 470p

R311 470k

B

R306

1/16W

1608

10

R314

R316

924 7

15k R317

470k

R318

1k

0.001u 1005

C311

B

10uH

L303

10

HALL_REF

HALL_OFFSET

11

12

B

C303

C304

4700p

10u

B

MA111-(K8).S0

D301

C302

0.01u 1005

6.3V

B

ATA

1.3

0.9

4

5

Vcc

IN2+6IN2-7OUT2

IC302

NJM12902V(TE2)

4.6

0.9

1

OUT12IN1-3IN1+

C

IN3-

OUT3

8

9

10

Q301

:TR MODEL

2SC4617HT2

:TRV MODEL

2SD2216J-Q

D

24P

CN301

DRIVE(+)

DRIVE(-)

CONT(+)

E

F

ZOOM

LENZ BLOCK

G

NIGHT_SHOT

HALL(-)

BIAS(-)

HALL(+)

BIAS(+)

TEMP

ZM_SENSE_OUT

GND

FC_SENSE_OUT

FC_SENSE_VCC

PLA/GLASS

ZM_SENSE_VCC

ZM_A

ZM_B

ZM_XB

ZM_XA

FC_A

FC_B

FC_XB

FC_XA

24

23

22

21

20

19

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

R302

Q301

*

R1.8/P2.8

DRIVE

R304

1k

R0.4/P0

1k

RB301 68kX2

2.8

00

2.8

1M

R307

Q302

RN2910FE(TPLR3)

FOCUS/ZOOM SENSOR SWITCH

2.8

R308 2200

C305

1005

0.1u B

R0.9/P0

R1.2/P0.4

R312

R1.2/P0.4

470k

C306

0.1u

B

1005

R310 220k

R309

10k

IN4-

IN3+

IN4+

OUT4

GND

11

12

13

14

0.1

0.7

R319

330

C312

RB302

0.47u

22KX2

B

L301

R1.2/P0.4

C314

XX

B

Q303

AMP

0.5

C313

0.01u B

1005

10uH

IC302

IRIS DRIVE

HALL BIASS

HALL GAIN

HALL AMP

*

0.01u

C317

1005

C318

C319

10u

B

R322

10k

R321

1k

C315

2200p

B R323

47k

6.3V

TA A

Q303 2SC4617HT2 2SD2216J-Q

0.1u B

:TR MODEL :TRV MODEL

HALL_GAIN

A_4.75V REG_GND

D_2.8V

MT_4.75V

LENS_FILTER_ON_SW

FC_RST_LED HALL_AD

ZM_RST_LED FC_RST

PLA/GLASS

ZM_RST

LENS_TEMP_AD IRIS_PWM

REG_GND

(MT_GND)

17

TO(9/11)

38

TO(10/11)

18

TO(7/11)

35

TO(6/11)

FOCUS/ZOOM MOTOR DRIVE

VC-251 (3/11)

H

ZOOM LENS BLOCK is replaced as a block so that the SCHEMATIC DIAGRAM and PRINTED WIRING BOARD are omitted.

C316 1u

B

1608

IC301

FOCUS/ZOOM

I

J

R301

47k

C301

XX

MOTOR DRIVE

2.8

R0.1/P0.6

R0.1/P0.4

4.8

R0.1/P0.3

17

18

19

20

21

22

23

24

VDD

MPC17A135DTAEL

IC301

1

4.8

VM23

OUT2B

R1.0/P0.1

PGND

OUT4B

OUT3B

0.1

4.8

PGND

OUT1B

VM!2OUT 1A3PGND4OUT2A5OUT3A6PGND7OUT4A8VM49IN110EN111IN212EN2

R2.6/P0.1

R0.1/P0.20R0.4/P00R0.4/P0

13

14

15

16

IN3

IN4

EN3

EN4

R1.4/P0

R2.8/P0

6.3V

0.01u 1005

C310

C308

B

47u

TR MODEL :CCD-TR618/TR618E/TR718E/TR728E/TR818 TRV MODEL :CCD-TRV49E/TRV58/TRV58E/TRV59E/TRV68/

K

TRV78/TRV78E/TRV88/TRV98/TRV98E

16

4-47 4-48

IRIS_COM

ZM_RST

FC_RST

DIR1B

DIR1A

EN1

DIR0B

EN0

DIR0A

14

TO(2/11)

For Schematic Diagram

• Refer to page 4-39 for printed wiring board.

• Refer to page 4-68 for waveforms.

1

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

38

5 136

924 7

10

11

12

VC-251 BOARD(4/11)

A

REC/PB AMP(RP BLOCK)

-REF.NO.:10000 SERIESXX MARK:NO MOUNT

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

B

B MECHA DECK(1/2)

(B200:NTSC MODEL) (B201:PAL MODEL)

C

D

E

SIGNAL PATH

Ref.signal

F

SIGNAL PATH

CHROMA

REC

PB

G

16

VIDEO HEAD

CH SP1

CH SP2

FLYING ERASE

VIDEO SIGNAL

Y/CHROMA

16P CN101

1LP2Y

2LP2X

3GND

4LP1X

5LP1Y

6GND

7GND

8GND

9SP1Y

10SP1X

11GND

12SP2X

13SP2Y

14GND

15FEY

16FEX

RECYREC/PB

AUDIO

SIGNAL

ET101

ET102

23

R101

:NTSC MODEL

56

:PAL MODEL

39

PB

220uH

3225

L101

23

0

C101

0.01u 1005

C106

R101

R4.2/P4.7

R102

560

C102

33u

6.3V

R109

27k

0.022u

C103

0.01u B

1005

R124

27k

Q102 2SA1774HT2 2SB1462J-Q

C105

XX

*

R105

100

R4.0/P4.7

Q101

2SA1965-S-TL

AMP

B

C107

R106

B

C104

0.01u 1005

27k

B

Q102

AMP

R108 4700

1005

R0.9/P0

C108

4.5

1005

0.01u

1005

0.022u

:TR MODEL :TRV MODEL

*

R4.5

/P4.6

0.7

FB101

4.5

R110

2.6

220

2.6

R111

2.5

220

FB102

0.7

4.5

R0.7/P0

R123

22k

R112

R107

270

2200

R113

C111 150p

R3.9/P4.0

R1.2/P2.3

TRANSISTORHN1B04FE-Y/GR(TPLR3)

RP_4.75V

MT_Q

L103

22uH

C118

C116

0.01u 1005

C113

0.1u B

1005

R116 2700

24

REC DUMP1

25

GND

26

REC1 OUT

27

PB1 IN

28

VCC AMP

29

PB DUMP1

30

PB DUMP2

31

BIASADJ

32

PB2 IN

33

REC2 OUT

34

GND

35

REC DUMP2

36

C110 100p

CH

220

CH

R1.1

/P2.8

1

2

354

Q103

C114

1005

L102 12uH

C112

82p

6

0.1u B

CH

37

R2.4/ P4.7

R3.5/P4.7

R2.3/P0

R2.4/P0

C119

0.01u

10u

1005

6.3V

± 0.5%

150kR118

18

19

20

21

22

23

VCC

VPSW1 OUT

4.6

2.3

RAMP IR

0.5

MT_Q

REC1 IN

RAMP V1

0.4

R2.9/P4.1

IC101

REC/PB AMP

IC101

CXA3265R-T4

27

RAMP V238REC2 IN39VSSW2 OUT40GND41PCM IN42RAMP CONT43RAMP44PCM REC45AFREC46BOTH_REC/DV PBPS

R0.4/P0.3

R3.0/P4.1

2700

R117

C117

0.01u 1005

RB101

22k

R115

33k

R3.6/

P4.7

C115

100p

CH

ERASE OSC

R120

22k

0.9

0.01u

B

0.01u

C136

MTIN

C121

0.1u

C135

1005

L104 220uH

B

17

0.2

C126

0.01u 1005

1005

XXC122

16

CARDET

R0.3/P2.0

MT_F0

13

14

15

MT_F0

PBRFOUT

P1.9

R0.1/

PCMOUT/MTSW

R0/P1.4

R2.2/P2.2

R4.4/P3.5

R0/P2.0

R2.1/P0

R2.0/P0

YLPFOUT/CARDETOUT

R0/P2.5

R2.4/P0.7

REC_Y/MT_CONT

SWP48REC_L_CONT

47

R0.3/P0

R1.5/P1.4

R3.2/P3.4

C123

Q104

0.01u B

SWITCH

1005

0

C124

0.01u 1005

RP_PB

P2.8

Y/C/ATF IN

*

REC_L_CONT

REC_Y/MT_CONT

RP_IR MT_F0

DOC_DET

MT_Q

3.8

SWITCH

2.5

DOC_DET CLPFOUT

AGC TC

RF AGCOUT

2.2

0

4.6

0

AFM IN

24

RP_IR

Y MIX

VCC3

26

DOP

12

11

10 9

8

7

6

0.01u

5

4

3

2

1

Q107 S2A1774HT2 2SB1462J-Q

R121 470k

R122 470k

C128

1005

C127

0.001u 1005

C130

0.01u

1005

:TR MODEL :TRV MODEL

DOC_DET

C131

0.01u

C129

4700p

1005

C133

0.01u 1005

B

REC_Y/MT_CONT

C132

0.01u 1005

Q106

XX

R3.9/P3.7

RB102

C134

0.47u B

B

RP_IR

B

10k

0

4.6

RN1904FE(TPLR3)

Q105

SWITCH

*

4.7

Q107

00

25

REC_L_CONT

C125

0.01u

B

1005

NTSC MODEL :CCD-TR618/TR818/TRV49/TRV58/TRV68/TRV78/TRV88/TRV98 PAL MODEL :CCD-TR618E/TR718E/TR728E/TRV49E/TRV58E/TRV59E/TRV78E/ TRV98E TR MODEL :CCD-TR618/TR618E/TR718E/TR728E/TR818

2.8

TRV MODEL :CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/ TRV78E/TRV88/TRV98/TRV98E

Q104 DTC144EHT2 UN9213J-(K8).SO

:TR MODEL :TRV MODEL

REG_GND

PB_RF

REC_L_CONT

REC_Y/MT_CONT

RP_IR

MT_F0

DOC_DET

MT_Q

RF_AGC_CONT

REC_AFM

MTSW

RF_AGC_OFF

AGC_SLOW

RP_PB_MODE

DOP

BOTH_REC

XFE_ON

XME/MP VC_RF_SWP

DOP

REC_RF

PB_C_RF

RF_AGC_OUT

PB_C_RF

PB_RF

REC_2

39

19

20

11

21

7

TO(10/11)

TO(9/11)

TO(7/11)

TO(2/11)

TO(1/11)

TO(11/11)

4-504-49

VC-251 (4/11)

REC/PB AMP

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

For Schematic Diagram

• Refer to page 4-39 for printed wiring board.

• Refer to pages 4-68,69 for waveforms.

1

VC-251 BOARD(5/11)

A

B

LINE IN/OUT AMP(IO BLOCK)

-REF.NO.: 10000 SERIESXX MARK:NO MOUNT

40

TO(10/11)

9

TO(2/11)

8

TO(1/11)

22

TO(11/11)

C

23

TO(7/11)

D

E

F

D_2.8V

A_4.75V

REG_GND KINUTA_Y_OUT

KINUTA_C_OUT

LINE_Y

VIDEO_I/O

C_I/O Y_I/O

IR_VIDEO

VC_SO

XVC_SCK

XCS_IO

SIGNAL PATH

VIDEO SIGNAL

CHROMA Y/CHROMA

REC

PB

Y

38

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

FB221

C221

0.1u B

1005

R226

0

VIDEO_I/O

VC_SO

XVC_SCK

XCS_IO

C_I/O

Y_I/O

C_I/O

RB223 68kX2

CL212

Y_I/O

CL208

CL210

R229 68

VIDEO_I/O

56

C223

L221

10u

10uH

6.3V

R232

22k

±0.5%

C227

C226

R0/P1.65

373839404142434445464748

2.2

CL009

XX B

C228

XX

B

C233

2.2u C225

1u

B

XX

B

1005

CL211

CL213

0

2.2

R2.7

25V

0

R0.3/P0

C231

XX

B

IR

MAIN_GND1

Y_IN1

MAIN_GND2

SYNC_SEP_TC

Y_IN2

CLAMP_TC1

Y_IN3

CLAMP_TC2

Y_IN4

Y_GCA_CONT

C_IN1

C235

1u

B

1608

INPUT_Y_OUT

28

C_GCA_CONT

123456789101112

0

C234

XX

B

1005

CL201

0.9

2.4

VREF

AGC_VVOUT

0.1

2.2

CH

XX

C236

CL202

0.1

PLL_GND

INPUT_C_OUT

IC221

LINE IN/OUT

AN2225FHQ-EB

29

C_IN2

MAIN_VCC

0

4.6

CL203

APC_FIL

BGT_OUT

IC221

C_IN3

D_GND

1005 B

0.01u

C238

1.4

0.1

EXTAL

PLL_VCC

C_IN4

D_VCCSIXSCK

2.8

CL204

4.6

R0.4/P0.2

CL205

XTAL

4.0

2.6

CL206

1.8

MM_TC3

32

33

31

30

2.8

CL207

0

252627282930313233343536

4FSC_OUT

XCS

1.7

MM_TC2

DRV_V_OUT

DRV_Y_OUT

DRV_C_OUT

C_GND

IR_V_OUT

V_VCC

V_INV

V_GND

Y_GND

Y_INV

Y_VCC

C_VCC

FP-249 (S/T REEL SENSOR, TAPE TOP), FP-356 (TAPE END), FP-355 (TAPE LED)

924 7

10

FLEXIBLE BOARD

— Ref. No. FP-249, 356, 355 Flexible board; 5,000 series —

L224 10uH

C252

DR_V_OUT_T

DR_Y_OUT_T

C248

2.2u 50V

10u 16V

C251

IR_VIDEO

RB221

1k

RB222

1k

DR_C_OUT_T

XX

B

4.6

0

1.9

1.6

1.3

R0/P1.9

SDC

13 14 15 16 17 18 19 20 21 22 23 24

C249 220u 4V

2.2u 50V

C247

0.01u

C250 220u

4V

C246

B

1005

IR_VIDEO

DR_C_OUT_T

DR_Y_OUT_T

DR_V_OUT_T

VC_SO

XCS_IO

XVC_SCK

G

16

LINE IN/OUT AMP

VC-251 (5/11)

S/T REEL SENSOR, TAPE TOP, TAPE END, TAPE LED

/

FP-249, FP-356, FP-355

4-52

For Schematic Diagram

• Refer to page 4-39 for printed wiring board.

• Refer to page 4-69 for waveforms.

1

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

38

5 136

924 7

10

11 14

12

VC-251 BOARD(6/11)

A

SERVO(SB BLOCK)

-REF.NO.:10000 SERIESXX MARK:NO MOUNT

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

B

C

D

E

F

G

H

I

J

B MECHA DECK(2/2)

(B200:NTSC MODEL)

(B201:PAL MODEL)

FP-356

FP-249

FLEXIBLE

H002 S REEL SENSOR

H001 T REEL SENSOR

FLEXIBLE

Q002

TAPE END

IN

OUT

21

IN

OUT

21

FP-220

FLEXIBLE

4

OUT

3

IN

4

OUT

3

IN

26

TO(7/11,11/11)

S901 MODE SWITCH

M901 DRUM MOTOR

FP-433

FLEXIBLE

ME/MP REC PROOF

24

TO(9/11)

25

TO(8/11)

27

TO(7/11)

M903 LOADING MOTOR

DEW SENSOR

Q001

TAPE TOP

HI8 MP

XREC_PROF_SW

M

PG

FG

M

M902 CAPSTAN MOTOR

S001

S002 C LOCK

CFG_DUTY

DEW_AD

XCC_DOWN

CAP_FG

CAP_FWD

HI8_MP_SW

ME_SW

CAP_ON DRUM_FG DRUM_PG

DRUM_ON

DRUM_START

MSW_C

MSW_B

MSW_A

FG

CN706

CN704

CN707

8P

10P

12P

OFFSET_ADJ

15PCN712

TAPE_TOP(C)

REC_PROOF

TEPE_END(C)

TAPE_LED(A)

SENSOR_VCC

TAPE_LED(K)

C_LOCK_SW

XCC_DOWN

HI8_MP_SW

XREC_PROF_SW

DRUM_ON

DRUM_START

COM_GND

M-SW(A)

M-SW(B)

M-SW(C)

LM(-)

LM(+)

FG_OUT

STAND_BY

FRC

MT_GND

VCC_2

VCC_1

REG_GND

DEW

REG_GND

HI8_MP

S_REEL(-)

S_REEL(+)

ME/MP

HALL_COM

T_REEL(-)

T_REEL(+)

CAP_FG

CAP_FWD

ME_SW

CAP_ON

DRUM_FG

DRUM_PG

MSW_C

MSW_B

MSW_A

VS

1

2

3

4

5

6

7

8

1PG

2FG-PG_COM

3FG

4COM

5W

6W

7V

8V

9U

10U

1

2

3

4

5

6

7

8

9

10

11

12

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

CFG_DUTY

DEW_AD

R452

RB451

330k

100k

R451

47k

MSW_A

MSW_B

MSW_C

DRUM_PG_SENS

FG_PG_COM

DRUM_FG_SENS

DRUM_COM

DRUM_W

DRUM_V

DRUM_U

R455 100k

TAPE_TOP_C

HI8_MP_SW

S_REEL_-

S_REEL_+

ME_SW

XREC_PROF_SW

TAPE_END_C

T_REEL_-

T_REEL_+

R457

XCC_DOWN

1234567

LM_-

LM_+

CAP_VS

DEW_AD

8

CAP_FG

CFG_DUTY

CAP_ON

CAP_FWD

470

2012 R459

2012 R460

2012

R458

VTR_UNREG

DRUM_ERROR

DRUM_W

DRUM_V

DRUM_U

DRUM_COM

C461

C459

0.1u B

1005

1

C451

0.1u

1005

DRUM_FG

DRUM_PG CAP_ON

D451

B

XX

C458

C453

0.1u 1005

C454

0.1u B C455

0.022u B C456

0.022u

C457

0.1u

1005

4.7u

C462

0.1u

B

1005

C463

0.1u B

1005

DRUM_ON

B

DRUM_START

1005

B

0.047u B

1005

35V

DRUM_FG_SENS

FG_PG_COM

DRUM_PG_SENS

C485 B 1608

2.8

12345678910111213141516

STBY D

0

RF

0.5

OSC

SELSLP1

0

SELSLP2

R1.3/P1.5

VS

R0.2/P0.3

CSLP1

0.3

CSLP2

VCC1

BRAKE

XX

FRC

R1.2/P1.4

FILTER

2.1

FC

RSAT

GND

1.4

FGOUT

C465

4700p

B

C466

0.1u B

1005

B

C467

C469

2200p

1.5

0.7

AGC

COM

0.7

V IN

U IN

V OUT

U OUT

0.7

36

IC451

DRUM DRIVE

DRUM FG/PG

WAVE SHAPER

37 39 4038

1.3

FG IN2

FG IN

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

C468

470p

C472,

XX XX 0 15K 0 15K

4700P

PG OUT1

1.3

VREF

PG IN

1.1

0.1

PGC

C470

1u

B

R467, R470, R480

R466,

C473,

0.022 10K47K 47K

10K

B

C471

2200p

0.7

W IN

LD DRIVE

REEL FG

IC451

CXA8096R

2.8

PG OUT2

C473

*

B

1005

C472

*

B

W OUT

CBEN

UNLOAD

0

DEC2

CBIN

0.3

LM_+

0.1u

R466

LOAD

0

0.3

C474

1005

DEC1

CBOUT

*

R467

LM_-

B

RS

R0/P0.1

0.4

CBLOUT

*

000

RFL

OUT1

DBIN

0.4

DBOUT

:NTSC MODEL :PAL MODEL

100k

R469

R468

3300

OUT2

0

ISNF

0.022u

R470

*

R471

1

XLM_LIM_ON

LM_LIM_CONT

49505152535455565758596061626364

0

2.8

LIMEN

LIM OUT

0.2

N.C

RSB

C475

B

1005

R0/P2.8

END OUT

END IN

TOP IN

R0/P2.8

TOP OUT

RLDO2

R1.9/P1.3

RLM2

RLM1

RLDO1

RLO2

RLO1

VCC2

RLP2

RLP1

R472

1

123

RB452

10k

C477

NC

1.3

4.8

VM

8.3

2.1

GND

2.1

1.7

C476

0.01u B

1005

0.047u 1005

C478 C479

33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

R474

47k

R480

*

B

0.047u

2.2uF2012

C480

0.1u B

1005

R481

4700

0.001u

4

1005

C482

0.001u 1005

1005

B

DRUM_ERROR

C481

B

TAPE_END_C

TAPE_TOP_C

T_REEL_-

T_REEL_+

S_REEL_+

S_REEL_-

CAP_ERROR

CAP_VS

CAP_ERROR

UNLOAD

LOAD

XLM_LIM_ON

LM_LIM_CONT

TAPE_LED_ON

C483 470p

B

C484 470p

B

XREEL_HALL_ON

DRUM_VS

DRUM_ERROR

CAP_VS

CAP_ERROR

MT_4.75V

D_2.8V

REG_GND

UNLOAD

LOAD

XLM_LIM_ON

LM_LIM_CONT

TAPE_END

TAPE_TOP

TAPE_LED_ON

TREEL_FG

SREEL_FG

XREEL_HALL_ON

CAP_PWM

DRUM_PWM

REG_GND

(MT_GND)

41

TO(10/11)

28

TO(7/11)

35

TO(3/11)

NTSC MODEL :CCD-TR618/TR818/TRV49/TRV58/TRV68/TRV78/TRV88/TRV98 PAL MODEL :CCD-TR618E/TR718E/TR728E/TRV49E/TRV58E/TRV59E/TRV78E/TRV98E

TAPE_LED_ON

TR MODEL :CCD-TR618/TR618E/TR718E/TR728E/TR818 TRV MODEL :CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/ TRV98E

SIGNAL PATH

R465

4700

C464

Drum speed servo

220p B

1608

Drum phase servo

Drum servo (speed and phase)

Capstan speed servo

Capstan servo (speed and phase)

REC

REC/PB

PB

C452

R462

150

1608

0.1u

1005

XREEL_HALL_ON

R464

R461

470

180

1608

4.1

1

C460

0.1u B

B

1005

2SC4617HT2 2SD2216J-Q

2

3

Q451

:TR MODEL :TRV MODEL

TAPE LED DRIVE

0

K

FP-355

FLEXIBLE

TAPE LED

D001

FLEXIBLE

FP-221

16

SERVO

4-544-53

VC-251 (6/11)

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

For Schematic Diagram

• Refer to page 4-39 for printed wiring board.

• Refer to page 4-69 for waveforms.

1

VC-251 BOARD(7/11)

MODE CONTROL(MC BLOCK)

A

-REF.NO.:10000 SERIESXX MARK:NO MOUNT

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

38

TO(5/11)

TO(11/11)

29

TO(9/11)

30

23

5 13

TO(1/11,8/11)

6

TO(4/11)

20

TO(1/11,2/11)

5

924 7

10

TO(2/11)

11 1514

13

TO(1/11)

3

12

TO(3/11)

18

B

PITCH_AD

YAW_AD

VST_C_RESET

V_LIGHT_PWM

VC_RF_SWP

EVF_VG

VC_RF_SWP

XCS_EVF_DA

XCS_LCD_DA

XCS_EVF_DA

LCD_HOLD

XCS_AU

DA_STB

XCS_IO

SYS_V

BOTH_REC

MTSW

XFE_ON

RP_PB_MODE

DOP

RP_PB_MODE

VC_RF_SWP

AGC_SLOW

VC_RF_SWP

AGC_SLOW

RF_AGC_OFF

XME/MP

MECHA_HD

MECHA_FLD

MECHA_VD

VC_SO

MECHA_HD

MECHA_FLD

VIVDO

XVC_SCK

XTBC_V_RST

TBC_VD

X1/2_SWP

ATF_SAMPLE

JOG_VD

SWP_DIR

ATF_SAMPLE

X1/2_SWP

JOG_VD

LCD_HOLD

MECHA_VD

LCD_HOLD

XCS_KINUTA

CK_CONT1

XRST_KINUTA

CK_CONT2

CK_CONT1

XRST_KINUTA

XCS_KINUTA

SWP_DIR

TBC_VD

SYS_V

XSG_V_RST

VC_SI

AFC_F0

VC_SI

VC_SO

XVC_SCK

XCH_SCK

CH_SO

XCS_CH

PLA/GLASS

FC_RST_LED

ZM_RST

HALL_AD

IRIS_PWM

LENS_TEMP_AD

FC_RST

LENS_FILTER_ON_SW

ZM_RST_LED

C

ZM_RST_LED

LENS_TEMP_AD

FC_RST

LENS_FILTER_ON_SW

HALL_AD

IRIS_PWM

ZM_RST

FC_RST_LED

D

XLM_LIM_ON

LM_LIM_CONT

LOAD

UNLOAD

TAPE_END

28

TO(6/11)

E

26

TO(6/11,11/11)

F

27

TO(6/11)

G

TAPE_TOP

SREEL_FG

TREEL_FG

CAP_PWM

DRUM_PWM

XREEL_HALL_ON

TAPE_LED_ON

CAP_FG

DRUM_START

CAP_ON

CAP_FWD

DRUM_ON

DRUM_FG

DRUM_PG

MSW_A

MSW_B MSW_C ME_SW

XREC_PROF_SW

HI8_MP_SW

H

I

J

42

TO(10/11)

REG_GND

EVF_DD_ON

D_2.8V

K

L

16

XLM_LIM_ON

LM_LIM_CONT

TAPE_END

TAPE_TOP

SREEL_FG TREEL_FG

CAP_PWM

DRUM_PWM

XREEL_HALL_ON

TAPE_LED_ON

DRUM_START

CAP_FWD

DRUM_ON

DRUM_FG

DRUM_PG

XREC_PROF_SW

HI8_MP_SW

R434

0

1608

LOAD

UNLOAD

CAP_FG

CAP_ON

MSW_A MSW_B

MSW_C

ME_SW

RF_AGC_OFF

XCS_EVF_DA

XCS_LCD_DA

DRUM_ON

XME/MP

DOP XCS_IO

XRST_KINUTA

XCS_KINUTA

XCS_AU

DA_STB

ZM_RST_LED

ZM_RST

FC_RST

WEE2P

CSE2P XREEL_

HALL_ON

LM_LIM_CONT

XLM_LIM_ON

CSE2P

XVC_SCK

VC_SO

R0.4/P0.2

VC_SI

R408

100k

C405

0.1u

2.8

B

1005

118

119

34

X0

X1

VSS

MD2

MD1

MD0

XRST_VC

BK/MX=L, BX/MEG=H

RF_AGC_OFF

EVF_DD_ON

XCS_EVF_DA

XCS_LCD_DA

DRUM_ON

XME/MP

DOP

XCS_IO

BK/BX=L, MX/MEG=H

XRST_KINUTA

XCS_KINUTA

XCS_AU

DA_STRB

ZM_RST_LED

ZM_RST_SENS

FC_RST_SENS

VDD

XWE_EEPROM

XCS_EEPROM

XREEL_HALL_ON

LM_LIM_CONT

XLM_LIM_ON

RB401

100kX4

8 6 4 2

SWP_DIR

120

VDD

TAPE_LED_ON

31

32

000

TAPE_LED_ON

LOAD

VFD_V

LOAD

C403

10p

X401

CH

20MHz

R402

560k

2.8

R401

1k

C401

1u

B

1608

IC401

BR9016RFV-E2

2.8

1

XCS

2.6

2

xBUSY

XSCK

3

OI

0.3

RST

4

GND

OO

10pCHC404

C402

IC401

Vcc

0.1u

EEPROM

1.1

1

1.0

2

3

4

5

6

2.8

7

0

8

0

9

0

10

2.8

11

2.8

12

2.8

13

2.8

14

0

15

R0/P2.8

16

17

2.8

18

2.3

19

2.8

20

0

21

2.8

22

2.8

23

2.8

24

25

2.8

26

2.8

27

1.4

28

0

29

2.8

30

7 5 3 1

2.8

8

100k

7

R403

2.8

6

5

WEE2P

MECHA_VD

0

117

MECHA_VD

UNLOAD

33

34

UNLOAD

DRUM_PG

0.1

116

DRUM_PG

VSS

MSW_A

DRUM_FG

MSW_A35MSW_B

VIVDO

CAP_FG

R404

R0/P1.3

R1.3/P1.3

2.8

113

114

115

MEM_VD

CAP_FG

DRUM_FG

MSW_C

36

37

38

00000

MSW_B

MSW_C

TBC_VD

MECHA_HD

100k

R0/P2.8

112

TBC_VD

MECHA_HD

REC_PROOF_SW

ME_SW

39

ME_SW

XREC_PROF_SW

CAP_FG

MECHA_FLD

R2.8/P0.2

1.5

R0/P2.8

109

110

111

CFG_HMS

CK_CONT2

MECHA_FLD

MECHA/CAMERA/SERVO

MB91191RPFF-G-163-BND-ER

TAPE_TOP

TAPE_END

HI8_MP_SW

40

41

42

0

2.8

TAPE_TOP

TAPE_END

HI8_MP_SW

SYS_V

XTBC_V_RST

1.3

2.5

107

108

SYS_V

IC402

CONTROL

XNS_ON_SW

43

44

0

2.8

LENS_FILTER_ON_SW

ATF_SAMPLE

R411 100k

R0/P2.8

106

Not Used

TBC_V_RST

IC402

ATF_SAMPLE

XSG_V_RST

45

R0/p0.4

RB407

XSG_V_RST

CK_CONT1

104

105

INT_VD

CK_CONT1

35

RP_PB_MODE

46

47

2.8

R0/P2.8

123

2200X2

4

RP_PB_MODE

VC_RF_SWP

R2.8/P0

102

103

VSS

X1/2_SWP(HSWP)

SWP

48

49

R1.4/P1.2

R1.4/P1.6

X1/2_SWP

XFE_ON

101

AVSS

XFE_ON

100

AVRH

DRUM_START

50

R1.0/P2.8

DRUM_START

2.8

0.01u

AVDD

AUDIO_OUT

51

0

C406

1005

99

52

YAW_AD

4700X2

RB402

B

98

N.C.

53

FC_RST_LED

PITCH_AD

123

1.3

97

YAW_AD

PITCH_AD

FC_RST_LED

AGC_SLOW

54

2.8

AGC_SLOW

TREEL_FG

SREEL_FG

4

100k

R433

1005

B

C407

0.01u

±0.5%

1.3

1.8

1.800

94

95

96

LENS_DETE

S_REEL_FG_AD

T_REEL_FG_AD

(V_LIGHT_PWM)YAW_PWM

N.C.

BOTHREC

SSS/MTSW

55

56

57

0

R0.3/P0

MTSW

BOTH_REC

R430

XX

R431

27k

91

92

93

N.C.

EVFVG_AG

XCS_CH/GCAM_PB

CH_SI/CAM/XLINE

XCH_SCK/AGC_DIRECT

(KINUTA→VC) VC_SI

(VC→KINUTA) VC_SO

VST_C_CHARGE

JOG_VD

58

59

60

000

JOG_VD

LCD_HOLD

VST_C_RESET

2.6

SYSTEM_AD

GENERAL_AD FOCUS_A_AD

FOCUS_B_AD

ZOOM_SW_AD

LENS_TEMP_AD

AFC_F0_IN

HALL_AD

SCK_VC

XCS_VC

(HI→VC) HI_SO

(VC→HI) HI_SI

HI_SCK

XCS_VC_STAR

PITCH_PWM

IRIS_PWM

DRUM_PWM

CAP_PWM

(OSCI) GND

(OSCO) NC

VC_F_BUSY

CAP_ON

CAP_FWD

LCD_HOLD

EVF_VG

ZOOM_VR_AD

R432 100k

±0.5%

90

2.8

89

88

87

1.4

86

1.5

85

R3.0/P1.3

84

R1.1/P0.4

83

R2.8

82

0

81

R2.8

80

R0.3/P0.5

79

0.2

78

2.6

77

R0/P2.9

76

0.2

75

0.1

74

0.3

73

2.8

72

V_LIGHT_PWM

71

0

70

R1.1/P0

69

68

VSS

67

66

65

VDD

64

63

62

61

2

1

0.5

4

3

RB406

0.5

10kX2

C409

XX

1005

2.8

R614

*

R613

*

R611

*

R612

*

XX

RB404

3

4

1

2

1005

B

C408

0.1u

R428 100k

R420

47k

1005

B

0.01uC410

C411

0.01u

B

1005

LENS_TEMP_AD

R417 2200

ZOOM_VR_AD

HALL_AD

XCS_CH

CH_SO

XCH_SCK

VC_SI

XCS_VC

HI_SO

HI_SI

XHI_SCK

IRIS_PWM

DRUM_PWM

CAP_PWM

CAP_FWD

CAP_ON

HI_SO

HI_SI XHI_SCK

XCS_VC

4

R423

XX

ZOOM_VR_AD

HI_SO

HI_SI

XHI_SCK

XCS_VC

XSYS_RST

R614 22k:TRV MODEL 100:TR818 R611 10k :TR618/TR818/TRV68/TRV78/TRV88/TRV98 22k :TRV49/TRV58 100k :TRV49E/TRV58E/TRV59E

R612 10k :TR618E/TR718E/TR728E/TRV78E/TRV98E 22k :TRV49E/TRV58E/TRV59E 100k :TRV49/TRV58

R613 10k :TR618/TR618E/TR718E/TR728E 22k :TR818/TRV78E/TRV98E 100k :TRV49/TRV49E/TRV58/TRV58E/TRV59E/

TRV68/TRV78/TRV88/TRV98

VC_SO

XVC_SCK

RB405

XX

123

31

TO(8/11)

15

TO(2/11,8/11,11/11)

SIGNAL PATH

REC/PB

REC

Drum speed servo

Drum phase servo

Drum servo (speed and phase)

Capstan speed servo

Capstan servo (speed and phase)

PB

MODE CONTROL

VC-251 (7/11)

4-55 4-56

For Schematic Diagram

• Refer to page 4-39 for printed wiring board.

• Refer to page 4-69 for waveforms.

1

VC-251 BOARD(8/11)

HI CONTROL(HI BLOCK)

-REF.NO.:10000 SERIES-

A

XX MARK:NO MOUNT

6

TO(1/11,7/11)

TO(9/11)

32

B

TO(1/11)

2

C

TO(2/11,7/11,

15

11/11)

16

TO(2/11)

D

31

TO(7/11)

TRV MODEL

HP_L_OUT

HP_R_OUT

CAM_DD_ON

XSYS_RST

OSD_SO

XCS_OSD

XOSD_SCK

EVER_3.0V

ZOOM_VR_AD

XHI_SCK

SYS_V

XCS_VC

BEEP

SP+

SP-

HI_SO

HI_SI

38

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

SYS_V

BEEP

CAM_DD_ON

XSYS_RST

OSD_SO

XCS_OSD

XOSD_SCK

ZOOM_VR_AD

XHI_SCK

HI_SO

HI_SI

XCS_VC

E

F

43

G

TO(10/11)

BATT_UNREG

VTR_UNREG

REG_GND

VTR_DD_ON

CAM_DD_ON

INIT_CHARGE_ON

DC_PACK_SW

FAST_CHARGE

BATT/XEXT_SW

BATT_SIG

D_2.8V

VTR_UNREG

VTR_DD_ON

CAM_DD_ON

INIT_CHARGE_ON

DC_PACK_SW

FAST_CHARGE

BATT/XEXT_SW

BATT_SIG

2

1

D501

MA132WK-(K8).SO

H

IC502 NJU7285AV-TE2:

S-8423YFS-T2:

I

J

HP_L_OUT

HP_R_OUT

IC504

1

GND

2

Vin

7.5

3

TR618/TR618E/TR718E/TR728E/TR818 TRV49E/TRV58E/TRV59E TRV49/TRV58/TRV68/TRV78 TRV78E/TRV88/TRV98/TRV98E

SP+

SP-

CHARGER

C501

0.1u B

BATT_SIG

MA111-(K8).S0

D504

XX

R503

R501 100k

1

2

1

2

C518

33

0.1u

R559

1005

LI_3V

2.8

N.C.

4

Vout

3

D503

MA728-(K8).S0

1

0

0.1

R502

2

0

3

3.0

4

B

451

36

0.2

R504 100k

3.6

VSS

PREEND

VBAT

CS

5 136

XHI_RESET

IC502

INITIAL RESET

BACK UP VCC

3.0

VRO

8

7.5

VIN

7

3.0

VOUT

6

3.0

RESET

5

IC502

*

C502

0.1u B

1005

0.2

2

I/F BLOCK

Q501

HN1L02FU(TE85R)

XCS_VC

XSIRCS_SIG XCHARGE_LED

XF_TALLY_LED

XIR_LED_ON

XSYS_RST

XVTR_MODE_SW

XCAM+STBY_SW XS/S_SW

XEJECT_SW

XCC_DOWN

XLANC_POWER_ON

LCD_COM/XDATA

INIT_CHARGE_ON

470kX4

RB502

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

11 1514

V_JACK_IN

XS_JACK_IN

4

123

79

80

81

82

83

84

85

86

2.7

VDD

XS_JACK_IN

V_JACK_IN

JACK_MONO(RCH)

SHOE_ON

EXT_MIC_DET

N.C

XCS_VSC

4241

NS_LIGHT_ON

XCS_OSD44OSD_SO45XOSD_SCK46CHARGE_INH47IB_SI48IB_SO49FAST_CHARGE

1.5

3.002.8

2.8

2.900.2

1.5

42

43

3

NS_LIGHT_ON

XCS_OSD

OSD_SO

XOSD_SCK

1k

R544

DC_PACK_SW

R542

47k

R543 560k

X501

20MHz

1

2

LCD_LED_ON

77

78

3.0

LCD_LED_ON

0.2

RB509 470k

2

1

4

3

76

AVDD

AVREF_1

HOTSHOE_ID2

HOTSHOE_ID1

232C_JACK

BATT/XEXT

(ex.VC_RF_SWP)

TEST_PORT(N8)

XCS_LCD_DRIVER

SIRCS_ENV

XWIIND_ON

MELODY_ENV

TALLY_LED

32KHZ_OUT

32KHZ_IN

0

50

R547

1M

3 1

RB513

XX

FAST_CHARGE

12

AVREF_0

75

GND

74

73

72

0

DEW

71

GND

70

69

RB510

2.7

1kX4

68

1

2.7

3

67

5

0

7

66

65

6800pC514

2.5

64

63

62

3.0

61

2.9

60

59

3.0

58

N.C

57

56

0

55

54

1.5

53

1.4

R552

52

10M

3.0

51

3.0

12

TRV MODEL :CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E TR MODEL :CCD-TR618/TR618E/TE718E/TR728E/TR818

SIGNAL PATH

REC

DS_BUSY

BATT_IN

4 2

DIAL B

DIAL A

SYS_V

GND

VDD

PB

17 20 2116 18 19

LANC_IN

KEY_AD5

TALLY_LED

XLANC_POWER_ON

XWIND_ON

XS_JACK_IN

V_JACK_IN

NS_LIGHT_ON

XSIRCS_SIG

XF_TALLY_LED

XCC_DOWN

DEW_AD

KEY_AD2

KEY_AD3

KEY_AD4

LCD_LED_ON

LI_3V

DIAL_A

DIAL_B

VTR_UNREG

XCHARGE_LED

SP+

SP-

TRV MODEL

XCS_LCD_DRIVER

LCD_COM/XDATA

OSD_SO

XOSD_SCK

RB511

470kX4

DEW_AD

BATT/XEXT_SW

XWIND_ON

TALLY_LED

DIAL_B DIAL_A

SYS_V

XHI_RESET

HP_L_OUT

HP_JACK_IN

HP_R_OUT

ZOOM_VR_AD

KEY_AD1

KEY_AD0

TRV98

XIR_LED_ON

XEJECT_SW

XCAM+STBY_SW

XVTR_MODE_SW

XS/S_SW

R711

220

8 R554 100k

1234567

2 4 6 8

B

R558

470

XCS_LCD_DRIVER

C517

0.1u B

1005

C515

22p

CH

4

X502

3

32.768kHz

C516 18p

CH

AUDIO

SIGNAL

LANC_OUT

KEY_AD5

TALLY_LED

XLANC_POWER_ON

XWIND_ON

XS_JACK_IN

V_JACK_IN

NS_LIGHT_ON

XSIRCS_SIG XF_TALLY_LED

XCC_DOWN

DEW_AD

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

1

2

3

4

5

6

7

8

R712

9

220

10

11

12

1

2

3

4

5

KEY_AD2

KEY_AD3

KEY_AD4

BL_GND

LCD_LED_ON

LI_3V

DIAL_A

DIAL_B

VTR_UNREG

D_2.8V

EVER_3.0V

XCHARGE_LED_ON

SP+(BEEP)

SP-

REG_GND

XCS_LCD_DRIVER

LCD_COM/XDATA

OSD_SO

XOSD_SCK

XHI_RESET

HEADPHONE_L

HP_JACK_IN

HEADPHONE_R

HEADPHONE_GND

12PCN710 ZOOM_VR

D_2.8V

REG_GND

XPHOTO_FREEZE

KEY_AD1

D_2.8V

KEY_AD0

LED_2.8V

NC

XIR_LED_ON

XEJECT_SW

REG_GND

XCAM+STBY_SW

XVTR_MODE_SW

REG_GND

XS/S_SW

REG_GND

33

TO(11/11)

25

TO(6/11)

24PCN709

TR MODEL

TO CF-077 BOARD CN001

THROUGH THE FFC-295 FLAT CABLE

(SEE PAGE 4-37)

TRV MODEL

TO CONTROL SWITCH BLOCK(CF-1000) CN001

THROUGH THE FFC-295 FLAT CABLE

(SEE PAGE 4-33)

CONTROL SWITCH BLOCK (FK-1000)

CONTROL SWITCH BLOCK (SS-1000)

5PCN711

S002

START/STOP

TRV98

D001

TLSU1002(TPX1,SONY)

S001

EJECT

RV001

W-T

RV001

20K

S003

TRV98

XX

SUPER LASER LINK

R002

10k

R001

10k

S001

POWER

PLAYER

OFF(CHARGE)

CAMERA

S012

R003 1200

S002

STOP

LIGHT

R004

R005

1200

1500

S006 PAUSE

S004

XX

R006 1500

CONTROL SWITCH BLOCK(FK-1000,SS-1000)are replaced as a block. So that its PRINTED WIRING BOARDS are omitted.

REW

R007 2200

S007

S005

R008 2200

S008

R009 3900

S010

FF

S009

PALY

S011

XX

R010 3900

R531

10k

KEY_AD1

123

2.8

4

HI_SI

KEY_AD0

2.8

KEY_AD093KEY_AD194KEY_AD295KEY_AD396KEY_AD497KEY_AD598KEY_AD699KEY_AD7

0.1

RB505

1kx2

0.2

HI_SO

TR MODEL

91NC92

2.6

0.2

XHI_SCK

10

8

7 5

6

RB506

3

4

10kx4

2

1 2

1

RB507

4

3

88

89

90

2.5

3.0

XDRY_BATT

ACV_SENSE

BATT_SENSE

IC503

MODE CONTROL

IC503

CXP921048A-029R-T6

TEST_PORT37XRESET38GND3920MHZ_OUT4020MHZ_IN41VDD

3.0

0

36

B

C513

0.022u

BEEP

XX

RB508

1k

3.0

VDD87GND

924 7

KEY_AD3

KEY_AD4

KEY_AD5

KEY_AD2

8

RB504

1kx4

C505

XX

C506

0.01u

C507

0.01u

C509

0.01u

C510

0.01u

C512

0.1uB1005

220kR518

C511

0.1uB1005

220k

R519

D505

2

1

470k

R520

±0.5%

470k

R521

±0.5%

RB503

470kX4

8

1234567

C503

C504

47u

0.1u

4V

B

1005

RB514 47kX2

1234567

R513 47k

RB501

1kX4 1 3 5 7

2.8

1

LANC_IN

0.2

LANC_OUT

2

2.9

XCS_VC

3

2.8

XSIRCS_IN

4

1.6

XCHARGE_LED

5

R0/P0.1

XF_TALLY_LED

6

1.6

XIR_LED_ON

7

N.C

8

2.8

XSYS_RST

9

N.C

10

N.C

11

XLANC_ON

12

GND

13

R2.8/P0

XVTR_MODE_SW

14

2

R0/P2.8

4

XCAM+STBY_SW

15

6

2.8

8

XS/S_SW

16

2.8

XEJECT_SW

17

0

XCC_DOWN

18

2.8

XPHOTO_FREEZE

19

XPHOTO_STBY_SW

20

2.8

XLANC_POWER_ON

21

HI_TXD

22

HI_RXD

23

0

LCD_COM_XDATA

24

3.0

INIT_CHARGE_ON

25

TRV MODEL

R516

1M

RB512

XX 1 3 5 7

R525

1k

1234567

B

1005

B

1005 1005

B

BC508

1005

B

1005

B

1005

±0.5%

XX

100

2.8

NC

CAM_DD_ON28VTR_DD_ON29XLANC_JACK_IN30HP_SENS31XLI_PRE_END32HI_SI33HI_SO34xHI_SCK35MELODY/SIRCS_CARRIER

3.0

3.003.0

26NC27

C519

0.047u B

2 4 6 8

CAM_DD_ON

VTR_DD_ON

HP_JACK_IN

K

16

HI CONTROL

4-584-57

VC-251 (8/11)

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

For Schematic Diagram

• Refer to page 4-39 for printed wiring board.

1

38

5 136

924 7

10

11 1514

12

VC-251 BOARD(9/11)

AUDIO(AU BLOCK)

A

-REF.NO.:10000 SERIESXX MARK:NO MOUNT

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

B

C

D

E

F

G

H

16

44

TO(10/11)

32

TO(8/11)

34

TO(11/11)

SIGNAL PATH

REC

PB

A_4.75V

AU_2.8V

MT_4.75V

AU_4.75V

REG_GND

HP_L_OUT HP_R_OUT

IR_L_OUT IR_R_OUT

AUDIO_L_I/O AUDIO_R_I/O

IR_CARR

IR_A_DEV IR_V_DEV

REC_AFM

VC_RF_SWP

AUDIO

SIGNAL

A_2.8V

BEEP

MIC_L

MIC_R

C602

10u

RF_AGC_CONT

AFC_F0_ADJ

FRQ_TUNE

AGC_CONT2

HALL_REF

HALL_GAIN

HALL_OFFSET

SWP(SEL)

B

1005

B

1005 1005

DOC_DET

RP_IR

MT_Q

STB(LD)

C397

68p CH

TA

0.01u

CLK

C601

1005

6.3V

DI

B

0.01u

A

C396

1005

15 16 17 18 19 20 21 22 23 24 25 26 27 28

REC_AFM

AU_BPF

B

1.5M_DEV

1.7M_DEV

2.6

0.2

2.3

3.7

R2.2/P2.3

1.9

2.1

0.7

0.5

0.9

1.5

0.8

1.6

0

R379

820

RF_AGC_CONT

AFC_F0_ADJ

HALL_OFFSET

VC_RF_SWP

RP_IR

REC_L_CONT

RF_AGC_CONT

REC_Y/MT_CONT

MT_F0

DOC_DET

MT_Q

XCS_AU DA_STB

HALL_GAIN

HALL_OFFSET HALL_REF

FRQ_TUNE

AFC_F0_ADJ

VC_SI

VC_SO

XVC_SCK

CFG_DUTY

XVC_SCK

VC_SO

DOC_DET

RP_IR

FRQ_TUNE

IR_V_DEV

HALL_REF

HALL_GAIN

DA_STB

MT_Q

IC601

D/A CONVERTER

(EVR)

RP_IR

REC_L_CONT

RF_AGC_CONT

REC_Y/MT_CONT MT_F0

DOC_DET

MT_Q

REC_AFM

PB_RF

XCS_AU

DA_STB

HALL_GAIN

HALL_OFFSET

HALL_REF

FRQ_TUNE

AFC_F0_ADJ

VC_SI

VC_SO

XVC_SCK

FSC CFG_DUTY

19

TO(4/11)

30

TO(7/11)

17

TO(3/11)

1

TO(1/11)

10

TO(2/11)

24

TO(6/11)

L601

10uH

1.8

RB352

47kx2

1

B

0.22u

C371

45

SP_IN

R0.7/P2.4

5

C372

2.3

B

44

SP_SIG

TRV MODEL

C374

22u

6.3V

2.3

42

43

CTLPF

SP_OUT

IC351

AFM PROCESSOR

CXA3285R-T6

C375

0.1u B

1005

B

2200p

C373

0

41

IC351

IC601

1234567891011121314

A_4.9V(VCC)

A_4.9V(VDD2)

R2.4/P1.2

REC_Y/MT_CONT

REC_L_CONT

MT_F0

REC_BIAS

ACC/RF_CONT

CFG_DUTY

1.5M_DEV

AU_BPF

1.7M_DEV

A_FADE

D_3.2V(VDD1)

GND

C389

0.22u B

1608

C394

0.47u

R373 470k

XX

C395

0.001u

C390

C391 1005

XX

0.01u

C392

0.01u B

C393

VC_RF_SWP

BH2222FV-E2

B

XX

B

XCS_AU

XVC_SCK

VC_SO

VC_SI

4.6

REC_Y/MT_CONT

REC_L_CONT

MT_F0

IR_CARR IR_A_DEV

CFG_DUTY

1.5M_DEV

AU_BPF

1.7M_DEV

A_FADE

FB601

1005 B

C377 XXBC376 XX

000

2.8

38

39

40

VCC

TC_R

TCH_R

NRDC_R

0

1.2

47k

R372

A_FADE

37

WEIGHT_R

1.1

1u B

C380

B

1u

C381BC379 XXBC378 XX

0

36

0

BC382 XX

TC_L

B

B 1005

B

1u

0.22u

0.1u

C383

C386

C384

1.1

0.5

1.2

1.1

34

35

33

TCH_L

NRDC_L

WEIGHT_L

PLL_LOOP_L

PLL_LOOP_R

RECFM_OUT/BPF_MONI

ST/MONO_TC

RF_AGC_TC

MONO_OUT(SO)

MIC_MONO

0

1.1

0.1

B

BC387 XX

1u

C385

R1.4/P1.6

R0/P0.7

MUTE_TC

R1.1/P1.6

BPF_ADJ

PB_RF_IN

RF_SWP

CS_IN

CK_IN

DEV_L

DEV_R

SI_IN

3.2

2.2

3.6

0.9

1.7

0.2

1.8

1.6

0

2.8

C603

1u

B

1608

C388

XX

B

32

R374

0

31

30

29

1.8

28

0

27

0

26

1.5

25

1.6

24

2.8

23

2.6

22

0.2

21

0.3

20

19

0.2

18

1.6

17

123

RB351

10k

4

Q354

HN1CO1FE-Y/GR

C363

0.22u

R364

B

100k

2.3

R363

8200

TR MODEL

SP+

SP-

TRV MODEL

IR_CARR

IR_A_DEV

IR_V_DEV

REC_AFM

VC_RF_SWP

R381

TRV MODEL

Q351

1

XX

1

2

3

0

2

Q353

3

XX

R382

2

47k

XX

1

0

2

Q352

DTC143THT2

SWITCH

3

0

Q355

RN4990FE(TPLR3)

ON/OFF MUTE SWITCH

0

0.5

3

1

5

6

4

0

C353

C356

XX

B

1005

TRV MODEL, TR818

R358

R354

C352

10u 16V

XX

16V

CL351 CL352

CL353

C354

R355 XX

R351

R352

10u 16V

C357

C359

R353

0

TRV MODEL

R356

C358

C355

XX

0.01u

B

1005

10k

100

47uC361

R359

XX

C362

XX

1k XX

6.3V

22u

16V

10u

C351

XX

B

C365

22u

6.3V

0

B

R2.7/P2.4

SP+

49

SP_GND

50

R2.0/P2.4

SP-

51

2.3

HP_L

C398

0.22u

52

HP_GND

53

0

HP_R

54

2.3

IR_OUT_L

55

2.3

IR_OUT_R

56

2.3

LINE_OUT_L

57

0

LINE_OUT_R

58

0

MUTE_OUT

59

4.7

VCCH

60

2.3

VREFH

61

1.1

VREF

62

R1.4/P0

MIC_IN_L

63

LINE_IN_L

64

C364

0.47u B

B

4V

MIX

3

6

2

4

1

1.8

234

BC369

0.22u

C367

10u 16V

4.8

2.4

46

47

48

SP_VCC

BEEP_IN

SP_VREF

R0.7/P2.4

AGCTC2MIC_IN_R3LINE_IN_R4REC_OUT_L5REC_OUT_R6AU_GND7PB_IN_L8PB_IN_R9FADER10IREF11RF_GND12IFDC_L13IFDC_R14FSC15RFDC_L16RFDC_R

1

0

0.1

R368 150k

C368

XX

C366

3.3u

50V

B

TR MODEL :CCD-TR618/TR618E/TR718E/TR728E/TR818 TRV MODEL :CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

AUDIO

VC-251 (9/11)

4-59 4-60

For Schematic Diagram

• Refer to page 4-39 for printed wiring board.

• Refer to page 4-69 for waveforms.

1

38

5 13

6

924 7

10

11 1514

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

12

1716

A

B

C

D

E

F

G

H

I

J

K

L

VC-251 BOARD(10/11)

DC-DC CONVERTER(DD BLOCK)

-REF.NO.:10000 SERIESXX MARK:NO MOUNT

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

7P CN001

(DCIN)(BATT)

+

S

-

BT901

BATTERY TERMINAL

C001

220p

B

C002

0.1u B

1005

C003

0.047u B

C004

1005

0.1u B

C005

1005

0.1u C060

B

1005

XX

VTR_DD_ON

B

1005

16

*MARKED:MOUNT TABLE

Q020

R039

R041

R042

R044

R045

R046

TR618/618E/718E/728E TRV49/49E/58/58E/59E

XX

0

100k

10k

XX

DCPACK_SW

BATT/XEXT

BATT_UNREG

BATT_GND

ACV_UNREG

BL_CONT

CAP_ERROR

DRAM_ERROR

R004

XX

±0.5%

1608

R001

22k

ACV_GND

BATT_SIG

33kR002

5600p

1

2

3

4

5

6

7

F005

XX

1k

R007

C009

C008

0.01u B

1005

1kR003

D001

MA728-(K8).S0

01ZA8.2(TPL3)

0.022u

0.7

1718

1.5

1920212223242526272829303132

0.8

B

1.2

0

1.5

2.0

1.5

8.2

2.9

1.6

0.7

R006

22k

TR818/ TRV68/78/78E/88/98/98E

TRANSISTOR 872905352

XX

68k

22k

100k

47k

18k

BATT_XEXT_SW

D002

C011

B

R011

1005

220

FEED_BACK-5

OUTPUT_MONITOR-4

INV_INPUT-4

FEED_BACK-4

RT

CT

SCP

MOS_DUTY

GND

SOFT_START

VREF

VCC

STANDBY-3

STANDBY

STANDBY-7

FEED_BACK-3

BATT_STG

TPC8305(TE12L)

8.0

R008 470k

D004

MA8082-(K8).S0

Q004

DTC144EHT2L

UN9213J-(K8)SO.

B

C013

4700p

0.4

1.3

0.7

INV_INPUT-5

FEED_BACK-6

NONINV_INPUT-5

OUTPUT_MONITOR-5

INV_INPUT-3

OUTPUT_MONITOR-3

FEED_BACK-2

INV_INPUT-2

33 34 35 36 37 38 39 40

1.5

1.0

1.5

13.4

R009

XX

33k

R012

B

470p

C012

BL_REG

CAP_VS

VL_UNREG

VTR_UNREG

BATT_UNREG

TRV MODEL

Q006

XNO9D61OOL

SWITCHING

8.2

F003

1.4A

1005 B

C025

C020

10u

0.1u

B

1005

63 64

0.001u

C021

B

1005

0.001u

C022

C023

0.001u B

1005

C024

0.001u B

1005

49 50 51 52 53 54 55 56 57 58 59 60 61 62

1

7.8

2

3

C026

8.2

8.1

C028

4.7u 10V

B

8.2

8.1

8.2

8.1

8.2

8.0

C027

4.7u

B

8.2

C029

4.7u

10V

B

4.9

6

5

4

C030

4.7u

4.7u 10V

10V

B

3216

Q009-Q012

SWITCHING

Q011

XN09D6100LS0

1

6

2

5

3

4

Q012

XN09D6100LS0

1

6

2

5

3

4

Q009

XN09D6100LS0

16

2

3

Q010 XN09D6100LS0 1

2

3

Q013

NM

342561

Q007 CPH6102-TL SWITCHING

Q008

XN09D6100LS0

SWITCHING

8.2

1

7.8

2

L001

22uH

B

5

4

6

5

4

0

R017 1k

Q003

2SB1132-T100-Q

0.1

Q004

*

1.7

Q001

7.8

8.2

12345678

OUTPUT-7

OUTPUT_VCC

BOOT_CAP_L-7

BOOT_CAP_L-6

BOOT_CAP_H-6

OUTPUT_GND-4,5,6,7

BOOT_CAP_H-5

BOOT_CAP_L-5

BOOT_CAP_L-4

BOOT_CAP_H-4

OUTPUT_GND-1,2,3

BOOT_CAP_H-3

BOOT_CAP_L-3

OUTPUT-2

BOOT_CAP_L-2

BOOT_CAP_H-2

6.5

8.2

C019

0.001u B

1005

DC_PACK_SW

INIT_CHARGE_ON

R022

47k

-4,5,6

OUTPUT-6

OUTPUT-5

OUTPUT-4

MOS_GATE-4

OUTPUT-3

OUTPUT_ VCC-1,2,3

ET001

XX

44

8.1

7.1

8.6

7.1

8.1

7.1

8.6

2.9

8.6

7.1

8.2

TRV MODEL

F004

1.4A

F002

1.4A

F001

1.4A

ET002

XX

FAST_CHARGE

Q003,004

CHARGE CONTROL

R052

22

Q002

SWITCH

1

7.8

4700

R014

0.4

INV_INPUT-6

NONINV_INPUT-6

IC001

DC/DC CONVERTER

OUTPUT_MONITOR-2

FEED_BACK-1

4.7

0.9

B

C014

1500p

TR MODEL :CCD-TR618/TR618E/TR718E/TR728E/TR818 TRV MODEL:CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

22

R013

8.2

2

8.2

7

8 5

63

D005

8.0

4

1SS357(T3SONY1)

C010

0.022u

R010

1M

1005

:TR MODEL

:TRV MODEL

TRV MODEL

R020

10k

B

22k

C015

2200p

R021

1.3

1.1

1.2

4.9

910111213141516

INV_INPUT-7

FEED_BACK-7

NONINV_INPUT-7

OUTPUT_MONITOR-6

IC001

CXA3057R-T6

INV_INPUT-1

OUTPUT_MONITOR-1

COMP

MOS_GATE-1

41 42 43 44 45 46 47 48

1.5

2.8

1.5

2.2

8.4

C016

0.001u 1005

8200

R016

7.6

R018 6800

8.2

7.8

B

00

HN1K02FU(T5RSONY)

CHARGE CONTROL

R023

33k

C017

XX

C018 470p

B

8.2

6.5

OUTPUT_VCC-7

BOOT_CAP_H-7

OUTPUT_MONITOR-7

43

BOOT_CAP_H-1

BOOT_CAP_L-1

OUTPUT-1

6.8

8.0

7.8

B

DRUM_VS

L003

4.7uH

C032

4.7u 10V

B

3216

1.3

L005

22uH

C035

4.7u

6.3V

1.3

1.5

2.8

4

45

3

2

1

4.7

6

5

43

HN1C01FE-Y/GR(TPLR3)

B

L006 33uH

C036

4.7u

6.3V B

L011

L007

4.7uH

22uH

C037

C039

2.2u

4.7u

6.3V

A

B

4.7uHL008

L009

L004 22uH

4.7uH

L010

4.7uH

FB001

C033

4.7u

6.3V B

T001

6

7

8

L013

4.7uH

L002

33uH

C031

4.7u

6.3V B

2SA1774HT2L

R026

22k

±0.5%

C038

10u

6.3V A

1SS383(T5RSONY1)

C034

0.01u

L016

22uH

(3225)

2SB1462J-Q

8.2

R025

47k

Q014

C059

0.01u

C041

1u

1SS383(T5RSONY1)

F

L012

22uH

(3225)

L014

C040

6.3V

Q016

2SB1132-T100-Q

B

D007

D010

1SS357

D006

22uH

22u

BL_CONT

VL_UNREG

VTR_UNREG

BL_REG

A_2.8V

AU_2.8V

A_4.75V

EVF_2.8V EVF_BL/BW_EVF_4.75V

EVF_13.3V

R073

:TR MODEL(EXCEPT TR818)

0

:TR818

1

Q021

*

Q023

*

4.3

R8.8/ P9.3

R038

22k

R040

22k

:TR MODEL

:TRV MODEL

R073

*

R074

1

Q072

MGSF1PO2LT

4.7

C071

0.01U B

R072

1M

1608

Q071

UN9213J-(K8)SO.

Q021

2SC4617HT2L

2SD2216J-Q

R-5.0/P0.4

R041

*

±0.5%

R042

*

±0.5%

R0/ P0.3

R043 220k ±0.5%

R12.0 /P0

R044

*

±0.5%

Q020

*

4.6

R4.1/ P4.2

R046

*

±5%

:TR MODEL

:TRV MODEL

3.9

C055

4.7u

EVF_BL/BW_EVF_4.75V

TR818

TRV MODEL

0

C072

0.01u B

:TR MODEL

:TRV MODEL

TR818

FB002

C054

4.7u F

3216

F

3216

2SD2216J-Q

±0.5%

100k

*

R045

C056

1u

F

2012

Q027

-15.4

-22.5

-21.9

R047

R048

100k

FB003

Q026

-15.3V REG

HN1AO1FE-Y/GR(TPLR3)

TRV MODEL

CAM_-7.0V

EVF_13.3V

CAM_15V

PANEL_-15.3V

R049

0

±5%

R050

220k

±0.5%

0

0.5

R051

68k

±0.5%

PANEL_13.3V

Note :

The components identified by mark 0 or dotted line with mark 0 are critical for safety.

LND008

:TR MODEL

:TRV MODEL

Q015

4.8

7.6

Q016

*

7.1

0.9

R027

10k

±0.5%

Q014,015

4.75V REG

C045

C049

33u

10u

4V

6.3V

A

R028

18k

±0.5%

1608

C042

4.7u 3216

C043

4.7u

2SA1774HT2L

2SB1462J-Q

A

TRV MODEL/TR818

F

3216

TRV MODEL

R033

22k

±0.5%

C052

10u

6.3V

R034

R029

10k

4700

±0.5%

D_1.5V

Q023

:TR MODEL

:TRV MODEL

A_4.75V

D_2.8V

A_2.8V

AU_2.8V

EVF_2.8V

R030

XX

R031

47k

1.5

-1.4

C047

2.2u

R032

F

22k

2012

C048

0.1u F

1608

EVF_PANEL_4.75V

MT_4.75V

A

*

Q018

EMERGENCY DETECT

AU_4.75V

A_4.75V

RP_4.75V

EVF_PANEL_4.75V

EVF_DD_ON

0

9.4

R036 100k

Q019

-7.0V REG

HN1A01FE-Y/GR(TPLR3)

CAM_DD_ON

15.2

R037 100k

R039

*

A_4.75V

R4.7/ P0

-15V REG

R035

47k

C053

0.1u B

1005

A_4.75V

2SC4617HT2L

2SD2216J-Q

Q018

DTC144EHT2L

UN9213J-(K8)SO.

R071

1M

1608

-7.0V REG

R0.5/ P0

R14.5/ P15.0

Q022

*

Q022

EVF_PANEL_4.75V

PANEL_13.3V

PANEL_-15.3V

VTR_UNREG

BATT_UNREG

D_2.8V

VTR_DD_ON

CAN_DD_ON

INIT_CHARGE_ON

DC_PACK_SW

FAST_CHARGE

BATT/XEXT_SW

BATT_SIG

VTR_UNREG

DRUM_VS

DRUM_ERROR

CAP_VS

CAP_ERROR

MT_4.75V

D_2.8V

EVF_DD_ON

D_2.8V

A_4.75V

A_2.8V

AU_2.8V

MT_4.75V

AU_4.75V

CAM_15V

A_4.75V

CAM_-7.0V

D_2.8V

A_2.8V

2012

F

RP_4.75V

2.2u

C057

D_2.8V

A_4.75V

D_2.8V

MT_4.75V

D_2.8V

D_1.5V

C058

A_2.8V

2.2u F

A_4.75V

2012

Replace only with part number

C062

XX

6.3V B

C046

22u

6.3V

C061

C051

22u

C050

6.3V

2.2u

A

6.3V A

specified.

SIGNAL PATH

Drum servo (speed and phase)

BL_CONT

VL_UNREG

VTR_UNREG

BL_REG

A_2.8V

AU_2.8V

A_4.75V

EVF_2.8V

EVF_BL/BW_EVF_4.75V EVF_13.3V EVF_PANEL_4.75V

PANEL_13.3V

PANEL_-15.3V

REG_GND

VTR_UNREG

BATT_UNREG D_2.8V

VTR_DD_ON

CAM_DD_ON INIT_CHARGE_ON

DC_PACK_SW

FAST_CHARGE

BATT/XEXT_SW

BATT_SIG

VTR_UNREG

DRUM_VS

DRUM_ERROR

CAP_VS

CAP_ERROR

MT_4.75V

D_2.8V

REG_GND

EVF_DD_ON D_2.8V

A_4.75V

A_2.8V

AU_2.8V

MT_4.75V

AU_4.75V

REG_GND

CAM_15V

A_4.75V

CAM_-7.0V

D_2.8V

A_2.8V

REG_GND

RP_4.75V

REG_GND

D_2.8V

A_4.75V

REG_GND

A_4.75V

D_2.8V

REG_GND

MT_4.75V

D_2.8V

D_1.5V

A_2.8V

A_4.75V

REG_GND

45

43

41

42

44

36

39

40

38

37

Note :

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

REC/PBREC PB

TO(11/11)

TO(8/11)

TO(6/11)

TO(7/11)

TO(9/11)

TO(1/11)

TO(4/11)

TO(5/11)

TO(3/11)

TO(2/11)

Capstan servo (speed and phase)

4-624-61

VC-251 (10/11)

DC/DC CONVERTER

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

For Schematic Diagram

• Refer to page 4-39 for printed wiring board.

1

38

5 136

924 7

10

11 1514

12

16

VC-251 BOARD(11/11)

CONNECTOR(CN BLOCK)

A

-REF.NO.:10000 SERIESXX MARK:NO MOUNT

EXCEPT TR818

B

VIDEO LIGHT

C

J201

S VIDEO

OUT

A/V OUT

J202

RFU DC OUT

C

Y

D

E

F

G

H

I

SIGNAL PATH

J

CHROMA

REC

PB

FP-257

VIDEO LIGHT,S VIDEO

G

VIDEO SIGNAL

FLEXIBLE

LND151

LIGHT VCC

LND152

LIGHT VCC

LND154

LIGHT GND

LND155

LIGHT GND

LND102

A

LND101

A

SOL001

TO MI-040/041 BOARD CN753

THROUGH THE FP-263 FLEXIBLE

(SEE PAGE 4-12)

Y Y/CHROMA

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

Q705 2SC4617HT2L 2SD2216J-Q

XF_TALLY_LED

VST_C_RESET

AUDIO

SIGNAL

VL_UNREG

UNREG_GND

XS_JACK_IN

S_C_I/O

REG_GND

S_Y_I/O

AUDIO_R_I/O

REG_GND

VIDEO_I/O

REG_GND

AUDIO_L_I/O

V_JACK_IN

REG_GND

RF_DC_OUT

CN702

MIC_R

REG_GND

MIC_L

SE_GND

YAW_AD

PITCH_AD

XSIRCS_SIG

XWIND_ON

A_2.8V

AU_2.8V

A_4.75V

IR_ON

IR_A_DEV

IR_V_DEV

IR_CARR

IR_L_OUT

IR_R_OUT

VTR_UNREG

IR_VIDEO

REG_GND

IR_FSC

CN703

NC

20P

:TR MODEL :TRV MODEL

24P

1k

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

19

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

CN701

20

19

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

CN715

BW_EVF_4.75V

1

2

3

4

:TR MODEL :TRV MODEL

20PCN713

VCO

XLANC_POWER_ON

EVF_BL

LANC_IN

EVF_BL_4.75V

LANC_OUT

EVF_VG

CAP_FG

PB_RF

REG_GND

BPF_MONI

IR_VIDEO

REC_RF

RF_SWP

NC

SE_GND

BL_GND

BL_REG

BL_CONT

PANEL_-15.3V

PANEL_13.3V

PANEL_4.75V

PANEL_2.8V

REG_GND

XVC_SCK

XCS_LCD_DA

VC_SO

PANEL_XVD

C-SYNC

PANEL_HOLD

PANEL_B

PANEL_G

PANEL_R

AD5

XSYS_RST

20P

EVF_BL_GND

EVF_BL

EVF_BL/BW_EVF_4.75V

XTALLY_LED

EVF_VG

EVF_13.3V

XVC_SO

XVC_SCK

XCS_EVF_D/A

EVF_GND

EVF_XVD

EVF_XHD

VCO

EVF_B

EVF_G

EVF_R

EVF_2.8V

20PCN708

4P

EVF_GND

BW_EVF_Y

XTALLY_LED

CPC

(FOR CHECK)

TO PD-131 BOARD CN5701

(SEE PAGE 4-19)

TO VF-141 BOARD CN4501

THROUGH THE FP-151 FLEXIBLE

(SEE PAGE 4-29)

EXCEPT TR818

TO VF-129 BOARD CN901

THROUGH THE FFC-256 FLEXIBLE

(SEE PAGE 4-25)

TRV MODEL

TR818

VCO

XLANC_POWER_ON

EVF_BL/BW_EVF_4.75V

LANC_IN

EVF_PANEL_4.75V

LANC_OUT

EVF_VG

TO(10/11)

CAP_FG

PB_RF

REC_AFM IR_VIDEO

REC_2

VC_RF_SWP

BL_REG

BL_CONT

PANEL_-15.3V

PANEL_13.3V

EVF_PANEL_4.75V

EVF_2.8V

XVC_SCK

XCS_LCD_DA VC_SO

PANEL_XVD

PANEL_SYNC

LCD_HOLD

PANEL_B

PANEL_G

PANEL_R

KEY_AD5

XSYS_RST

EVF_BL/BW_EVF_4.75V

EVF_VG

EVF_13.3V

XCS_EVF_DA

PANEL_XHD

VCO

EVF_B EVF_G/BW_Y

EVF_R

EVF_2.8V

TALLY_LED

R3.0/P0

EXCEPT TR818

Q702,703 VIDEO LIGHT DRIVE

Q702

CPH3106-PM-TL

0 8.2

C707

8.2

XX

R701

1k

XX

D703

XX

VDR701

2SB1132-T100-Q

C701

47u

6.3V

8.2

2SK1829(TE85L)

VDR703

Q704

4.7

Q704-705 CURENT LIMITER

Q703

VDR704

20

19

VDR702

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

24

23

22

21

20

19

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

R702

220

R703 100K

VDR706

4.7

L705

10uH

VL_UNREG

C708

4.7u B

3216

0

V_LIGHT_PWM

XS_JACK_IN

AUDIO_R_I/O

VIDEO_I/O

AUDIO_L_I/O

V_JACK_IN

D702

01ZA8.2(TPL3)

VDR707

R708

6.8

A_4.75V

4.7

R706

R704

6.8

R705

1k

4.4

Q705

*

R707

4.0

22k

5600

XF_TALLY_LED

YAW_AD

PITCH_AD

VST_C_RESET

XSIRCS_SIG

XWIND_ON

AU_2.8V

A_4.75V

NS_LIGHT_ON

IR_A_DEV

IR_V_DEV

IR_CARR

IR_L_OUT

IR_R_OUT

VTR_UNREG

IR_VIDEO

MIC_R

MIC_L

A_2.8V

C_I/O

Y_I/O

12

TO(2/11)

22

TO(5/11)

33

TO(8/11)

21

TO(4/11)

34

TO(9/11)

29

TO(7/11)

TO(2/11,

15

7/11,8/11)

26

TO(6/11,7/11)

FSC

PANEL_R

PANEL_G

PANEL_B

EVF_G/BW_Y

PANEL_XVD

PANEL_XHD

PANEL_SYNC

XVC_SCK

VIDEO_I/O

IR_VIDEO

LANC_IN

LANC_OUT

KEY_AD5

TALLY_LED

XLANC_POWER_ON

XWIND_ON

XS_JACK_IN

V_JACK_IN

NS_LIGHT_ON

XSIRCS_SIG

XF_TALLY_LED

IR_L_OUT

IR_R_OUT AUDIO_L_I/O

AUDIO_R_I/O

IR_CARR

IR_A_DEV

IR_V_DEV

REC_AFM

VC_RF_SWP

PITCH_AD

YAW_AD

VST_C_RESET V_LIGHT_PWM

EVF_VG

VC_RF_SWP

XCS_LCD_DA

XCS_EVF_DA

LCD_HOLD

XSYS_RST

CAP_FG

EVF_R

EVF_B

VC_SO

C_I/O

Y_I/O

PB_RF

REC_2

MIC_L

MIC_R

FSC

XLANC_POWER_ON

PANEL_R

PANEL_G

PANEL_B

EVF_R

EVF_G/BW_Y

EVF_B

PANEL_XVD

PANEL_XHD

PANEL_SYNC

VC_SO

XVC_SCK

VIDEO_I/O

IR_VIDEO

LANC_IN

LANC_OUT

KEY_AD5

TALLY_LED

XWIND_ON

XS_JACK_IN

V_JACK_IN

NS_LIGHT_ON

XSIRCS_SIG

XF_TALLY_LED

PB_RF

REC_2

IR_L_OUT

IR_R_OUT

AUDIO_L_I/O

AUDIO_R_I/O

MIC_L

MIC_R

IR_CARR

IR_A_DEV

IR_V_DEV

REC_AFM

VC_RF_SWP

PITCH_AD

YAW_AD

VST_C_RESET

V_LIGHT_PWM

EVF_VG

VC_RF_SWP

XCS_LCD_DA

XCS_EVF_DA

LCD_HOLD

XSYS_RST

CAP_FG

C_I/O

Y_I/O

FSC

BL_CONT

VL_UNREG

VTR_UNREG

BL_REG

A_2.8V

AU_2.8V

A_4.75V

EVF_2.8V

EVF_BL/BW_EVF_4.75V

EVF_13.3V

EVF_PANEL_4.75V

PANEL_13.3V

PANEL_-15.3V

BL_CONT

VL_UNREG

VTR_UNREG

BL_REG

A_2.8V AU_2.8V

A_4.75V

EVF_2.8V

EVF_BL/BW_EVF_4.75V

EVF_13.3V

EVF_PANEL_4.75V

PANEL_13.3V

PANEL_-15.3V

REG_GND

45

TRV MODEL, TR818

R713 220

R709

R710

TR818

TR MODEL :CCD-TR618/TR618E/TR718E/TR728E/TR818 TRV MODEL :CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/ TRV78/TRV78E/TRV88/TRV98/TRV98E

Q701

LED DRIVE

*

R0/P0.5

Q701 DTC144EHT2L UN9213J-(K8)SO.

K

16

CONNECTOR

VC-251 (11/11)

4-63 4-64

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

K

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

FP-257 (VIDEO LIGHT, S VIDEO) FLEXIBLE BOARD

— Ref. No. FP-257 Flexible board; 10,000 Series —

FP-257 FLEXIBLE

20

(VIDEO LIGHT)

1

J201

Y

G

C

G

S VIDEO

OUT

A/V

OUT

J202

RFU DC

OUT

1-680-198- 11

FP-257

FP-260

CONTROL SWITCH BLOC (SS-1000)

4-65

VIDEO LIGHT, S VIDEO

FP-257

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

VF-129

BOARD

REC/PB

2

IC901 3



3

IC901 7



4

IC901 qa

1.1Vp-p

16.7 msec

0.9Vp-p

H

5

IC901 qd

H

1.1Vp-p

H

2.4Vp-p

6

IC901 qh

1

IC901 1,5

2.0Vp-p

16.7 msec

2.0Vp-p

16.7 msec

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

4-3. W AVEFORMS

CD-281/286

REC

1

2



3



4



IC191 1,2

IC191 3,4

IC191 7

H

IC191 qs“ 

BOARD

H

6.8Vp-p

0.6Vp-p

MI-040/041

REC/PB

1

IC3901 7

IR ON

3.5795 MHz

2

IC3901 ws

IR ON

0.5 µsec/div

3

IC3901 ra

IR ON

H

BOARD

0.2Vp-p

0.9Vp-p

0.6Vp-p

PD-131

1

IC5501 rk

H

2

IC5501 rj

H

3

IC5501 rh



H

4

IC5501 w;



BOARD

0.5Vp-p

105 nsec

5

IC191 qd,qf¢

6

Q191 E



105 nsec

H

4.6Vp-p

6.8Vp-p

0.6Vp-p

5

IC5501 ws



6

IC5501 wf

7

IC5502 1



2H

H

3.0Vp-p

2.8Vp-p

WAVEFORMS

CD-281/286, MI-040/041, PD-131, VF-129

4-66

8

IC5502 wh

6 MHz

3.0Vp-p

CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/

TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E

VF-141

1

IC4501 w;

2

IC4501 ws



3

IC4501 wf



4

IC4501 rh

BOARD

2H

7.2Vp-p

LB-062

1

IC4601 4

BOARD

H

4.6Vp-p

CF-077

1

IC001 2

BOARD

25.346 kHz

3.0Vp-p

5

IC4501 rj

6

IC4501 rk

7

IC4502 wh

2H

10.86 MHz

0.5Vp-p

0.43Vp-p

0.50Vp-p

1.3Vp-p

4-67

WAVEFORMS

VF-141, LB-062, CF-077

Sony CCD-TR618, CCD-TR718, CCD-TR728, CCD-TR818, CCD-TRV49 Service manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Table for difference of function

SERVICE NOTE

SELF-DIAGNOSIS FUNCTION

GENERAL

DISASSEMBLY

2-1. VIDEO LIGHT (VIDEO LIGHT MODEL)

2-2. LCD SECTION (PD-131 BOARD) (TRV MODEL)

2-3. FRONT PANEL SECTION, MI-040/041 BOARD

2-4. CABINET (L) SECTION

2-5. CABINET (R) SECTION (CF-077 BOARD) (TR MODEL)

2-6. CABINET (R) SECTION [ CONTROL SWITCH BLOCK (CF-1000) ] (TRV MODEL)

2-7. VF-129 BOARD (B/W EVF MODEL)

2-8. VF-141, LB-062 BOARDS (COLOR EVF MODEL/TR818)

2-9. BATTERY PANEL SECTION (BATTERY TERMINAL BOARD)

2-10.LENS SECTION

2-11.VC-251 BOARD

2-12.MECHANISM DECK

2-13.HINGE ASSEMBLY (TRV MODEL)

2-14.CIRCUIT BOARDS LOCATION

2-15.FLEXIBLE BOARDS LOCATION

BLOCK DIAGRAMS

3-1. OVERALL BLOCK DIAGRAM (1/2)

3-2. OVERALL BLOCK DIAGRAM (2/2)

3-3. CAMERA/VIDEO BLOCK DIAGRAM (1/2)

3-4. CAMERA/VIDEO BLOCK DIAGRAM (2/2)

3-5. VTR/CAMERA CONTROL BLOCK DIAGRAM

3-6. SERVO BLOCK DIAGRAM

3-7. MODE CONTROL BLOCK DIAGRAM

3-8. AUDIO BLOCK DIAGRAM

3-9. LCD BLOCK DIAGRAM

3-10.B/W EVF BLOCK DIAGRAM

3-11.COLOR EVF BLOCK DIAGRAM

3-12.POWER BLOCK DIAGRAM (1/2)

3-13.POWER BLOCK DIAGRAM (2/2)

PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

4-1. FRAME SCHEMATIC DIAGRAM (1/2)

FRAME SCHEMATIC DIAGRAM (2/2)

4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

CD-281/286

MI-040/041

PD-131

VF-129

VF-141

LB-062

CONTROL SWITCH BLOCK(CF-1000)

CF-077

VC-251

FP-249, FP-356, FP-355

FP-257

4-3. W AVEFORMS