Sonova USA ICUBE2 User Manual
iCube II
User Guide
Contents
1. Welcome 4
2. Description 5
3. iCube II accessories 6
4. Getting started 7
4.1 Set up the power supply 7
4.2 Battery and Charging 8
4.3 Operating time 10
4.4 Switching iCube II On and O 10
4.5 Target tting software requirements 10
5. Connecting iCube II to your computer 11
5.1 Wireless connection setup 11
5.2 Connecting via USB cable 12
6. Using iCube II 13
6.1 Wearing iCube II 13
6.2 Detecting and programming
hearing instruments 14
6.3 Programming hearing instruments
outside of ears 16
2
7. Indicator lights 17
7.1 Charging indication 17
7.2 On / o indication 17
7.3 Battery status indicaton 18
7.4 Fitting status indication 18
7.5 Pairing 19
7.6 Firmware update indication 19
7.7 Malfunction indication 19
8. Troubleshooting 20
9. Declaration of conformity 22
10. Service and Warranty 23
10.1 International warranty 23
10.2 Warranty limitation 23
11. Compliance information 24
12. Information and explanation of symbols 27
3
1. Welcome
iCube II is designed specically for use by the hearing
care professional and enables the wireless transfer
of tting data from the PC to the client’s hearing
instruments.
Please read this user guide carefully to benet from all
the features of the iCube II.
For further information, please visit the Phonak website
www.phonakpro.com
Phonak – life is on www.phonak.com
4
2. Description
Alternative rear
neckloop opening
Neckloop plugs
Middle indicator
light (battery and
PC activity)
On / O
Right tting
indicator light
iCube II USB adapter
Mini USB
charging input
Pairing
button
Left tting
indicator
light
5
3. iCube II accessories
J USB cable, 3 m (10 ft.)
J iCube II desktop charger
J USB hub
Contents may vary depending on country.
*available as an option
*
6
4. Getting started
4.1 Set up the power supply
Select the adapter that corresponds to your country.
UK AUS US EU
J Insert the top round end of the
adapter into the round corner
of the power supply.
J Click the tail of the adapter in
to lock it into place.
J To remove, pull back the tab on
the power supply.
J Pull the adapter upwards to
remove it.
1.
1.
2.
2.
7
4. Getting started
4.2 Battery and Charging
Before using iCube II, the internal
battery charged. To do so, connect
iCube II with your fitting PC using a
USB cable.
If you use the iCube II charging
station, install it by plugging the
power supply into a power outlet.
Place iCube II into the charging
station as shown.
It is recommended that you charge iCube II whenever it
is not in use. This way it will be sufficiently charged and
ready for the next fitting session.
8
iCube II charging station is available as an option
Battery notes
When charging your iCube II for the rst time, leave
it to charge for at least three hours (even if the
battery indicator light changes to green color earlier).
Charging an empty battery will take approx. 2 hours.
It is safe to leave iCube II connected overnight.
A new battery’s full performance is achieved only
after two or three complete charge and discharge
cycles.
The iCube II battery can be charged several hundred
times. If the operating time of your iCube II reduces
substantially, please contact your local Phonak
representative.
For safety reasons, recharge the battery only with
chargers supplied by Phonak.
9
4. Getting started
4.3 Operating time
The operating time of iCube II greatly depends on the
usage of the device. Heavy use will reduce the operating
time of your iCube II between battery recharges. Fully
charged, your iCube II will operate for up to twelve hours.
4.4 Switching iCube II On and O
Slide the switch as
shown to switch iCube II
on or o.
O On
Once iCube II is fully operational, the middle
indicator light will ash slowly.
Switch iCube II o when not in use. The battery
indicator light will turn o.
4.5 Target tting software requirements
Before using iCube II, ensure that Target 4.0 or a later
version is installed on the tting PC.
10
Loading...