SOLTRON M-60 TURBO POWER, L-65 TURBO POWER, XL-75 TURBO POWER Operating Instructions Manual
Operating Instructions
1001659-00A- / us / 04.2007
M-60 TURBO POWER
2
Identify your tanning device . . . . . . . . . . . . . . . . . . . . . . . . . .3
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
3
Customer Service
Identify your tanning device
For contact with Customer Services, please write down
the device number of your tanning device.
Global Service USA
A Div of JK Products & Services, Inc.
#1 Walter Kratz Drive
Jonesboro, AR 72401
800-445-0624
870-935-9046
e-mail: support@jkamerica.com
http://support.jkamerica.com
5
4
Tanning times
Skin types
Skin types
For the recommended exposure schedule (see page 5).
Skin type I (Sensitive):
Invariably gets sunburn, accepts little natural sunlight and does not tan.
Skin type II (Fair):
This is the individual that usually burns easily and severely, tans
minimally or lightly and peels.
Skin type III (Average):
Often referred to as “Average” complexion, burns moderately and tans
about average.
Skin type IV (Brown):
This individual burns minimally, tans easily and above average with each
exposure.
Skin type V (Dark Brown):
This individual’s system rarely burns, tans easily and substantially.
5
“This product is in conformity with performance standards for sunlamp products under CFR21 Part 1040.”
Note:
Description of skin types see
Page 4.
6
Foreword
Foreword
Dear Customer,
The Soltron device you have purchased is a technically advanced and
powerful product. Your device was manufactured with the greatest care
and precision. It went through numerous quality and safety checks in order to guarantee trouble-free, safe operation. Nonetheless, you can also
make a significant contribution to your long-term satisfaction with your
device. Following the tips and instructions in the instruction manual will
ensure you enjoyment and pleasure with your device.
If you have any questions, we are always available to answer them.
1)
Yours sincerely
Soltron, Inc.
• Read and observe the information in this instruction manual. This will
enable you to prevent accidents and provide you with a reliable device ready for use.
• Always observe current legal and other regulations and legal requirements as well as the applicable environmental protection regulations.
1) (866) 243 9861
Note:
We reserve the right to make technical changes to the illustrations and specifications in this instruction manual.
Reprinting and reproduction, in whole or in part, of this manual is only permitted with our previous written approval and
with the source specified.
Table of Contents
7
Table of Contents
Table of Contents
Skin types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Tanning times. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Important safety notes and information. . . . . . . . . . . . . . . . .9
Safety notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Obligations of the studio operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Instructions pertaining to a risk of fire, electric shock, or injury . . . . . . 11
Instructions pertaining to a risk of damage to the machine . . . . . . . . . 13
Meaning of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Export . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Product information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Maintenance and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Environmental protection information . . . . . . . . . . . . . . . . . . . . . . . . . 19
Use the sunbed – but use it properly! . . . . . . . . . . . . . . . . . . . . . . . . . 20
Operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Operation: overview . . . . . . . . . . . . . . . . . . . . . . . . . . Fold-out page 22
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Tanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
To interrupt tanning session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Settings during start-up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Running time of accent lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
IR function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Regulating facial tanners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Switching shoulder tanner off and on
1)
. . . . . . . . . . . . . . . . . . . . . . . . 30
Regulating body cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Regulating facial cooling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Selecting music channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Adjusting volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Maintenance instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Power Off device and secure against being switched on again . . . . . 43
Maintenance: overview . . . . . . . . . . . . . . . . . . . . . . . . Fold-out page 44
1) optional
8
Table of Contents
Table of Contents
Cleaning intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Maintenance intervals, installed lamps and order numbers. . . . . . . . . 45
Relamping/maintenance instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Cleaning/replacing UV low-pressure lamps in sunbed base . . . . . . . . 51
Cleaning/replacing UV low-pressure lamps in shoulder tanner . . . . . . 53
Cleaning/replacing UV low-pressure lamps in side section . . . . . . . . . 55
Cleaning/replacing UV low-pressure lamps in canopy . . . . . . . . . . . . 57
Cleaning/replacing interior lighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Cleaning/replacing UV high-pressure lamps and filter panels in
the side section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Cleaning/replacing UV high-pressure lamps and filter panels in the
canopy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Cleaning/replacing accent light in the canopy . . . . . . . . . . . . . . . . . . . 68
Cleaning/replacing accent light in the frontpanel . . . . . . . . . . . . . . . . . 70
Cleaning filters in the sunbed base . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Cleaning filter mats in the canopy . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Cleaning filter mats in the shoulder tanner . . . . . . . . . . . . . . . . . . . . . 75
Presettings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Changing presettings with the control panel . . . . . . . . . . . . . . . . . . . . 77
Changing presettings with a hand-held unit. . . . . . . . . . . . . . . . . . . . . 79
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
JK-Products, Inc. – Limited Warranty . . . . . . . . . . . . . . . . . 88
Timer operation – see manual “Intellitan Remote Timer”,
Order no. 801129-..
Please read and observe ...
9
Safety notes
Important safety notes and information
Safety notices
Description of warning signs
Danger notices, damage to persons:
Warning notices, damage to persons:
Caution notices, damage to property:
Important information:
DANGER!
Type and source of danger, e.g. “DANGER – High voltage!”
Description of the consequences, e.g. “You can be killed or
injured by an electric shock!”
Countermeasures:
– Disconnect device from power supply before opening.
– Do not reach into the inside with the device switched on.
WARNING!
Type and source of danger, e.g. “Warning – hot surface!”
Description of the consequences, e.g. “You can burn your
hand (skin, face)!”
Countermeasures:
– Do not touch hot parts and nearby surfaces.
– Wait until hot parts and surfaces have cooled down.
Caution!
The word “Caution” with this label points out that danger for
devices, materials and the environment can be expected
here.
Note:
This symbol does not identify safety notices, but states information for a better understanding of the processes.
10
Please read and observe ...
Safety notes
Intended use
The tanning device is intended exclusively for cosmetic tanning of the human skin.
• The device is meant for commercial use only, not for home use.
• This device is used for tanning one adult person at a time.
• The user wears suitable eye protection that blocks UV radiation during tanning.
Any other use shall be considered improper. The manufacturer cannot be
held liable for damage or injuries resulting from this. The operator bears
the sole risk for this.
The proper use also includes compliance with the manufacturer’s instructions, operating and maintenance conditions. This device may only be
operated, maintained and repaired by persons familiar with these tasks
and who have been informed of the dangers involved.
Obligations of the studio operator
• As the operator you are responsible for informing users on possible
risks during tanning.
• All danger and safety labels attached to the device must be observed!
Do not remove them!
• No safety equipment (e.g. panel switch) may be removed or deactivated which can impair the safe operation of the device!
• The device may only be operated in a serviceable condition!
• The operator is bound to ensure that the equipment is handled correctly.
Please read and observe ...
11
Safety notes
Instructions pertaining to a risk of fire, electric shock, or injury
DANGER!
DANGER – High voltage!
You can be killed or injured by an electric shock!
Assembly and electrical connection must comply with national and local regulations.
– The device may only be assembled, installed, upgraded
or repaired by specially trained and instructed personnel.
WARNING!
WARNING – ultraviolet radiation!
Unprotected tanning may result in eye injury and eye diseases.
The unprotected eye can become inflamed on the surface,
and in certain cases the retina can be damaged by excessive radiation. Cataracts can form after frequently repeated
exposure to radiation.
– Inform users to use the included protective goggles
that block UV (Order No. 84592-..).
WARNING!
WARNING – ultraviolet radiation! Follow instructions!
Failure to use protective eyewear may result in severe
burns or other eye injury. If discomfort develops, discontinue use and consult a physician.
– A person who does not tan in the sun most likely will not
tan from the use of this device. Persons with very sensitive skins (skin type I) must not use the unit, as with this
skin type tanning is impossible without damaging the
skin (e.g. sunburn).
– Individuals with acute sunburn, individuals who have
had or have skin cancer, or individuals who are at increased risk of skin cancer, must not use the system.
– UV devices must not be used without taking medical ad-
vice if unexpected effects, such as itching, occur within
48 hours of the first session.
– The sunbed must never be used if a filter panel is miss-
ing or damaged, or the timer is defective!
– UV light from the sun or UV systems can cause injuries
to the skin or eyes. This biological effect is dependent
on the sensitivity of the individual's skin and on the type
and amount of UV light.
– As with natural sunlight, overexposure can cause eye
and skin injury, sunburn, and allergic reactions.
12
Please read and observe ...
Safety notes
– Repeated exposure may cause premature aging of the
skin and skin cancer.
– Medications or cosmetics applied to the skin, may in-
crease sensitivity to ultraviolet light.
– A person having a history of skin problems should con-
sult a physician before use.
WARNING!
WARNING – ultraviolet radiation!
Danger of long-term consequences.
– Overexposure should be avoided.
– The elderly should not use this equipment.
– Nursing infants and small children through age 7 years
may not use this device.
– The following applies to minors under the age of
18 years: Only use tanning devices in agreement with a
parent or guardian, or after consulting a physician.
– While there is no immediate clinical evidence of UVA ex-
posure and its effects upon expectant mothers, it is
strongly advised that expectant mothers be discouraged
from using the tanning unit.
WARNING!
WARNING – risk of infection!
Infections can be transferred through skin contact.
All items/equipment components, with which the user can
come into contact during tanning, must be disinfected after
every tanning session:
• Protective goggles
• Headrest
• Acrylic sunbed
• Handles and control panel
Please read and observe ...
13
Safety notes
Instructions pertaining to a risk of damage to the
machine
Note:
Occasionally, persons using the tanning device will experience a slight reddening of the skin – usually in small patches – after the second or third session. This redness is often
accompanied by an itching sensation. This may be nothing
more than a heat “rash” caused by heat from the lamps
within the device. It is generally very limited and caused by
constant contact of the skin with the acrylic surface. It
should go away within approximately 24 hours and should
not reappear. This rashing can be lessened or prevented by
applying moisturizer lotion to the affected area after the tanning session is completed.
– Follow instructions.
– The time between the first two tanning sessions must be
at least 24 hours.
– Increasing tanning also requires an extension of the ex-
posure time (= radiation time) or after a certain degree
of tanning has been achieved, a further intensification is
not possible. However, the radiation time may not be extended as desired within the scope of the permissible radiation doses! Therefore, only a certain degree of final
tanning dependent on the skin type can be achieved
without endangering your health.
– Inform users about proper tanning.
CAUTION – danger of overheating!
Danger of overheating by obstruction of the air routing.
– Do not change, obstruct or block the air inflow and out-
flow area to the device or make any unauthorized
changes to the device. The manufacturer shall bear no
liability for damage or injuries resulting from such actions.
– Before putting a tanning device into operation, the trans-
port pallet must be removed from under the device.
Danger of overheating by obstruction of the air routing.
14
Please read and observe ...
Symbols
Meaning of symbols
General symbols
Inform Customer Services
Soltron key
Do not touch, hot surface!
Suction cup
Low-pressure lamp(s)
UV low-pressure lamp(s)
Starter for low-pressure lamp(s)
UV high-pressure lamp(s)
Filter panels
Cleaning and disinfectant agents
Part/item number (for orders)
Operation
Display of tanning time
Display of run-on time (fan run-on)
Fault display (example),
see separate manual
Display of Music Channel 1 (Channel 1)
Factory setting: 1 channel
Customer service can set up to 7 channels
Display when adjusting volume
Please read and observe ...
15
Symbols
Description
Accent lights
Press button
Press button for 2 seconds
Duration: 3 minutes
Loudspeaker
Headphone connection
Technical Data
Maintenance
e.g.
2s
0-3 mi
n
Caution, safety switch!
Unscrew/release screw
Tighten/lock screw
Cleaning
Replacing
Clean or replace depending on soiling
Visual inspection
Filter/filter mat
Filter and filter mats must not be damp.
16
Please read and observe ...
Guidelines / Export / …
Guidelines
This device was built conforming to UL STD 482, and is certified to CAN/
CSA STD C22.2 2 No. 224.
Export
We would like to point out that these devices are exclusively intended for
use in the USA and Canada and may not be exported to other countries
and operated there! The manufacturer assumes no liability whatsoever
in the event of non-compliance! We explicitly emphasize that high liability
risks may occur for the exporter and/or the operator in the event of noncompliance.
Accessories
Some accessory parts are taken into account in the maintenance schedule beginning on Page 44, however this does not automatically mean that
your device is provided with this equipment.
An overview of the possible accessories is provided in the sales documentation and the planning manual. See page 23 for a selection of these.
Continuation of work steps on next page
End of work step
Presettings
Troubleshooting
...
Please read and observe ...
17
Maintenance and care
Product information
Acrylic glass panels
The acrylic glass panels for the tanning devices are produced of acrylic
glass developed especially for this application. The acrylics used are
characterized by a particularly high UV permeability and resistance, as
well as an easy-care, hygienic surface that is gentle to the skin.
The acrylic glass panels are formed to their shapes for the specific devices in a technically complex production process. Despite state-of-the-art
production know-how, the presence of minor spots, air bubbles or
streaks in the acrylic panels is unavoidable. In addition, microfine hairline
cracks can occur on the bed surface during operation.
These occurrences are material-dependent and are unavoidable in processing, however have no significant effect on the use or value and can
therefore not be recognized as defects.
Maintenance and care
Maintenance and care play a major role in deciding whether the device
meets the requirements placed on it in a satisfactory manner. The compliance with the specified maintenance intervals and the careful conducting of the maintenance and care work are therefore absolutely necessary
– see Page 44.
The current operating hours of the parts requiring maintenance can be
displayed in the Presetting mode – see Page 77 ff.
CAUTION!
Cosmetics or sun screen products must be removed prior to
using the sunbed as they can cause damage (e.g. fine
cracks on the surface) when used continuously.
DANGER!
Extreme danger! High voltage!
During maintenance work there is a risk of touching live
parts and receiving a fatal electric shock.
– Disconnect device from power supply before opening –
also see Page 43.
– Do not reach behind covers and do not open the device
with the device switched on.
– Refit any safety devices (e.g. switches) after the work
has been completed.
CAUTION!
Only use genuine spare parts of the same type!
The use of other parts may limit or void your manufacturer’s
warranty!
Any liability is excluded in case of damage or injury proven
to be the result of the use of non-genuine spare parts.
18
Please read and observe ...
Cleaning
Cleaning
Acrylic glass surfaces Plastic surfaces
For cleaning the other plastic surfaces, it is best to use warm water and
a leather cloth. Never use aggressive cleaning agents containing alcohol
or essential oils. These may lead, in the long run, to damage not covered
by the warranty.
During cleaning, a slight discoloration of the leather cloth by the rubber
seals must be expected for production-related reasons.
CAUTION!
Do not rub with a dry cloth – danger of scratching!
For fast, hygienic proper cleaning of acrylic glass surfaces,
use a specially developed fast disinfectant cleaner.
Other cleaning agents, especially concentrated disinfectants or solvents (e.g. Lysoform, ethyl alcohol or other liquids containing alcohol) must never be used for cleaning.
Failure to observe this voids all warranty claims.
Note:
Prevent damage to plastic surfaces. Remove rings, watches, bracelets etc. before the start of cleaning work.
02756 / 0
Please read and observe ...
19
Environmental protection
information
Environmental protection information
Environmental Declaration – The JK Corporate Group
The JK corporate group is subject to the strict regulations of EC Directive
761/2001 and the ISO 14001 standard, and undergoes regular internal
and external environment audits performed by trained auditors.
Environmental regulations – disposal of lamps
UV low-pressure lamps and UV high-pressure lamps contain fluorescent
materials and other waste containing mercury.
According to the national waste disposal laws and in accordance with the
municipal waste regulations, proof must be provided of the proper disposal of UV lamps.
Your local environmental agency will be happy to assist you with the disposal of UV lamps.
Packaging
All packaging consists of 100 % recyclable materials.
Disposal of recyclable materials
The device has been produced of recyclable materials. When being
scrapped later, the device must be disposed of properly. Sun Ergoline
will provide you with information on the content or potential hazards of
the materials used.
20
Please read and observe ...
Use the sunbed properly
Use the sunbed – but use it properly!
A few things need to be noted to get maximum enjoyment from a sunbed.
Here are some answers to some frequently asked questions.
Make-up on the sunbed?
Please remove make-up or don't use make-up while tanning. Clean skin
absorbs UV light better.
A wide variety of ingredients are found in cosmetics. Again, whether
these are emulsifiers, greases, or so-called scents – in conjunction with
UV radiation, these can cause allergic reactions of the skin.
Accordingly, a must before using a sunbed is: Remove all make-up. This
is essential. Make-up clogs the pores in the face. The UV light from a
sunbed re-opens these clogged pores so that not only does the light penetrate the skin, but also the allergenic components of the make-up.
A further negative consequence of make-up is that the appearance of the
skin deteriorates irreversibly over a period of time. However good a decent make-up might be – in conjunction with UV light, it causes more
harm than good. Therefore: Remove all make-up before a session on
your sunbed – it will be much better applied afterwards.
Showering after leaving the sunbed?
The browning is in the skin, not on it. Therefore you cannot wash it off.
Treat your skin to a moisturizing cream after showering.
Are medications and the sunbed compatible?
It is known that some medications increase the skin's sensitivity to UV
light. This probability is particularly high with antibiotics, sulphonamides,
psychiatric drugs, tranquillizers, anti-diabetes treatments and diuretics.
Sun creams which contain psorale or kumarin also increase skin sensitivity. If you are in any doubt, first ask your doctor - then you can enjoy
the sun at no risk.
Contact lenses on the sunbed?
The answer is: Yes! Like any other sunbed user, contact lens wearers
should also wear special protective goggles which protect the eyes
against UV radiation. To guarantee better protection, wearers of spectacles and contact lenses can ask their optician for exchange contact lenses with UV protection. The UV-A and UV-B filters built into exchange
contact lenses will protect the cornea and the internal parts of the eye
against almost 100% of the energy in UV radiation.
This will benefit sunbed users not only in the open air, but on the sunbed
itself. For more information, ask your optician or optometrist.
23
Operation
Accessories
24
Operation
Tanning
Start of tanning
The device is started automatically with an internal or external timer.
Preparation time
Before the UV lamps turn on, you have a few minutes to prepare yourself.
During the preparation time you can switch on the UV lamps at any time
by pressing the START/STOP button.
– Remove your clothes and all jewelry.
– Remove make-up and other cosmetics.
– Remove glasses. Contact lenses can be worn under the protective
goggles.
– Put on the protective goggles.
– Lie down on the bed surface.
– Close the canopy.
– Press the START/STOP button.
1) Order no 801129-..
Note:
Timer instructions: see separate manual
1)
.
25
Operation
Interrupt or end tanning session
The tanning session ends automatically after the preset time has run
down. The internal fan continues to run for approx. three (3) minutes to
sufficiently cool the device.
– To interrupt a tanning session, press button START/STOP anytime
during a session.
– Press START/STOP again to restart the lamps.
Settings during start-up
26
Operation
Running time of accent lighting
The accent lights are automatically switched
on at the end of the tanning session after the
set operating time and are switched off again at
the beginning of the next tannings session.
The running time of the accent lights in the
Standby mode can be changed with the presettings – see from Page 77 on.
Stand-by
Presettings
IR Function
27
Operation
Regulating facial tanners
Switching the facial tanners OFF:
– Press button for two (2) seconds.
Switching the facial tanners on again:
– Press button . It takes approx. one (1) minute until the facial tan-
ners reach their full output.
Adjusting the intensity:
– Press button .
– While the button flashes, press + or – to adjust the intensity of
the facial tanners.
1
...
Operation
28
2
STOP: Press for two (2) seconds.
3
...
29
Operation
START
4
Loading...