USER WEIGHT LIMITATION: 350lbs(160kgs).
SERIAL NUMBER (found on frame):
2 735i TREADMILL
For future service or related questions:
Please staple your receipt and/or write in the name and phone number of the retail store where you purchased your treadmill.
Name: ______________________________ Phone Number: ___________________ Receipt: ______________________
Precautions:
WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read the following important precautions
and information before operating the treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of all warnings and precautions.
•Use the treadmill only as described in this manual.
•Place on a level surface, with 6 feet 2 X1m of clearance behind it. Do not place the treadmill on any surface that blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill.
•When choosing a location for the treadmill be sure that the location and position permit access to a plug.
•Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a garage or covered patio, or near water.
•Do not operate the treadmill where aerosol products are used or where oxygen is being administered.
•Keep children under the age of 12 and pets away from the treadmill at all times.
•The treadmill should not be used by persons weighing more than 350LBS (160 Kgs).
•Never allow more than one person on the treadmill at a time. Wear appropriate exercise clothing when using the treadmill. Do not wear loose clothing that could become caught in the treadmill. Athletic support clothes are recommended for both men and women. Always wear athletic shoes. Never use the treadmill with bare feet, wearing only stockings, or in sandals.
•When connecting the power cord, plug the power cord into a grounded circuit. No other appliance should be on the same circuit.
•Always straddle the belt and allow it to start moving before stepping onto the belt.
•Always examine your treadmill before using to ensure all parts are in working order.
•Allow the belt to fully stop before dismounting.
•Never insert any object or body parts into any opening.
•Follow the safety information in regards to plugging in your treadmill.
•Keep the power cord away from the incline wheels and do not run the power cord underneath your treadmill. Do not operate the treadmill with a damaged or frayed power cord.
•Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be performed by an authorized service representative, unless authorized and/or instructed by the manufacturer. Failure to follow these instructions will void the treadmill warranty.
•Never leave the treadmill unattended while it is running.
•Use “safety key” when operating the treadmill and make sure the “safety key” is clipped to the users clothing.
•Remove the “safety key” and store it in a safe place when the treadmill is not in use. Keep the “safety key” away from children.
www.smoothfitness.com 3
Pour réparations futures ou questions connexes :
Please staple your receipt and/or write in the name and phone number of the retail store where you purchased your treadmill.
Name: ______________________________ Phone Number: ___________________ Receipt: ______________________
Précautions:
AVERTISSEMENT : Pour réduire les risques de brûlures, d’incendie, de choc électrique ou de blessures aux personnes, lire les précautions importantes et l’information suivantes avant de se servir du tapis roulant. Il revient au propriétaire de s’assurer que tous les utilisateurs de ce tapis ont bien été informés de tous les avertissements et précautions.
•Utiliser le tapis seulement comme il est décrit dans ce manuel.
•Le placer sur une surface plane, en laissant 2X1m d’espace libre en arrière. Ne pas placer le tapis roulant sur une surface qui bloque les ouvertures d’air.
•Pour protéger le plancher ou un tapis de dommages, placer un petit tapis sous le tapis roulant.
•Choisir pour le tapis roulant un emplacement et une position qui permettent d’avoir accès à une prise murale.
•Garder le tapis roulant à l’intérieur, à un endroit sans humidité ni poussière. Ne pas mettre le tapis roulant dans un garage, sur une terrasse couverte ou près de l’eau.
•Ne pas faire fonctionner le tapis roulant pendant la vaporisation de produits aérosol ou l’administration d’oxygène.
•Ne pas laisser les enfants de moins de 12 ans et les animaux s’approcher du tapis roulant.
•Le tapis roulant ne doit pas être utilisé par des personnes pesant plus de 160 kg (350 lb).
•Il ne doit jamais y avoir plus d’une personne sur le tapis à la fois. Porter des vêtements d’exercice appropriés pour utiliser le tapis roulant. Ne pas porter de vêtements lâches qui pourraient être pris dans le tapis roulant. Les vêtements de soutien athlétiques sont recommandés tant pour les hommes que pour les femmes. Porter toujours des chaussures d’athlétisme.
Ne pas être pieds nus, ou porter seulement des chaussettes ou des sandales lors de l’utilisation du tapis roulant.
•Brancher le cordon d’alimentation dans un circuit avec mise à la terre. Aucun autre appareil ne doit être sur le même circuit.
•Toujours enjamber le tapis et le laisser commencer à rouler avant de monter dessus.
•Toujours examiner votre tapis roulant avant de l’utiliser pour s’assurer que toutes les pièces fonctionnent correctement.
•Laisser le tapis s’arrêter complètement avant de descendre.
•Ne jamais insérer d’objets ou de parties du corps dans une ouverture.
•Suivre les directives de sécurité en ce qui concerne le branchement de votre tapis roulant.
•Garder le cordon d’alimentation éloigné des roues inclinées et ne pas faire passer le cordon d’alimentation sous votre tapis roulant. Ne pas faire fonctionner le tapis roulant si le cordon d’alimentation est endommagé ou effiloché.
•Débrancher toujours le tapis roulant avant de le nettoyer ou de le réparer.
•Toute réparation au tapis doit être effectuée par un réparateur agréé, à moins d’autorisation ou de directives contraires du fabricant. Le non-respect de ces instructions annulera la garantie du tapis roulant.
•Ne jamais laisser le tapis roulant sans surveillance lorsque la clé de sécurité est insérée.
•Utiliser la « clé de sécurité » pour faire fonctionner le tapis roulant et s’assurer qu’elle est accrochée aux vêtements des utilisateurs.
•Retirer la « clé de sécurité » et la ranger dans un endroit sûr lorsque le tapis roulant n’est pas en fonction. Garder la « clé de sécurité » hors de la portée des enfants.
4 735i TREADMILL
Power Requirements:
IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN THE RISK OF AN ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE PRODUCT IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILL NOT FIT THE OUTLET; HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.
This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes, surges and noise interference can result from weather conditions or from other appliances being turned on or off. To reduce the possibility of treadmill damage, always use a surge protector (not included) with your treadmill.
Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge protector with a UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltage rating of 400V or less and an electrical rating 120VAC, 15 amps.
This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance for electric current, should the treadmill malfunction. This treadmill is equipped with an electrical cord that has an equipment-grounding conductor and a grounding plug. Always plug the power cord into a surge protector, and plug the surge protector into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in the drawing below.
GFCI outlets and GFCI / AFCI Circuit Breakers are NOT recommended for use on this product. GFCI outlets and GFCI / AFCI Circuit Breakers may cause this equipment to function improperly.
www.smoothfitness.com 5
Alimentation :
UN MAUVAIS BRANCHEMENT DU CONNECTEUR DE MISE À LA TERRE DE L’ÉQUIPEMENT POURRAIT PROVOQUER UN CHOC ÉLECTRIQUE. EN CAS DE DOUTE, CONSULTER UN ÉLECTRICIEN OU UN RÉPARATEUR QUALIFIÉ POUR SAVOIR SI LE PRODUIT EST CORRECTEMENT MIS À LA TERRE. NE PAS MODIFIER LA FICHE FOURNIE AVEC LE PRODUIT. SI ELLE N’ENTRE PAS DANS LA PRISE, FAIRE INSTALLER UNE PRISE APPROPRIÉE PAR UN ÉLECTRICIEN PROFESSIONNEL.
Ce tapis roulant pourrait être gravement endommagé en cas de changement soudain de tension dans votre alimentation électrique. Les conditions météorologiques ou la mise sous tension ou hors tension d’autres appareils électriques peuvent provoquer des pointes de tension, des surtensions ou un brouillage. Pour réduire la possibilité que le tapis soit endommagé, toujours utiliser un limiteur de surtension (non inclus) avec votre tapis roulant.
Il est possible d’acheter des limiteurs de surtension dans la plupart des quincailleries. Le fabricant recommande un limiteur de surtension UL 1449 à prise unique comme suppresseur de tension transitoire (TVSS) ayant un taux de suppression de tension de 400 V ou moins et une tension électrique de 110 V C.A., 15 A.
Ce tapis roulant doit être mis à la terre pour réduire le risque de choc électrique. La mise à la terre fournit une voie de moindre résistance au courant électrique en cas de mauvais fonctionnement du tapis roulant. Ce tapis roulant est équipé d’un cordon électrique avec un conducteur de mise à la terre et une fiche de mise à la terre. Brancher toujours le cordon électrique dans un limiteur de surtension et brancher le limiteur de surtension dans une prise appropriée, correctement installée et mise à la terre conformément à tous les codes locaux et ordonnances.
Ce produit doit être utilisé avec un circuit nominal de 110 volts et à une fiche de mise à la terre qui ressemble à celle illustrée cidessous.
Les prises avec disjoncteur de fuite de terre et les disjoncteurs de fuite de terre ne sont PAS recommandés pour ce produit. Les prises avec disjoncteur de fuite de terre et les disjoncteurs de fuite de terre pourraient provoquer un mauvais fonctionnement de cet équipement.
6 735i TREADMILL
Open the boxes:
Open the boxes of your new equipment. Inventory all parts included in the boxes, and Supplied Hardware lists on page 7 for a full count of the parts included. If you are missing any parts or have any questions contact us directly at 888-800-1167
Gather your tools:
Before you begin, make sure that you have gathered all the necessary tools you may require to assemble the unit properly. Having all of the necessary equipment at hand will save time and make the assembly quick and hassle-free.
Clear your work area:
Make sure that you have cleared away a large enough space to properly assemble the unit. Make sure the space is free from anything that may cause injury during assembly. After the unit is fully assembled, make sure there is a comfortable amount of free area around the unit for unobstructed operation.
Invite a friend:
Some of the assembly steps may require heavy lifting. It is recommended that you obtain the assistance of another person when assembling this product.
User Weight Limitation:
Please note that there is a weight limitation for this product. If you weigh more than 350LBS (Approx. 160 Kgs). It is not recommended that you use this product. Serious injury may occur if the user’s weight exceeds the limit shown here. This product is not intended to support users whose weight exceeds this limit.
Care and maintenance:
The safety level can be maintained only if it is examined for damage and wear.
Replace any defective components immediately and stop all use of the equipment until repaired.
Always take care when mounting the equipment. Straddle the equipment by placing your feet on the straddle rails. Dismount from the equipment only after all parts have stopped.
Always check the wear and tear components like pulley, belts, etc.…To prevent injury.
There is an emergency stop, in the form of a SAFETY KEY, to prevent injury; you can stop the treadmill immediately by actuating the emergency stop for emergency dismount.
www.smoothfitness.com 7
This list identifies the major components you will use to assemble this product.
No. |
|
Description |
Qty. |
|
|||
|
|
|
|
A1 |
Treadmill Base |
1 |
|
A2 |
Console Assembly |
1 |
|
735i -301 |
Right Upright |
1 |
|
735i -302 |
Left Upright |
1 |
|
735i -307 |
Right Handle Bar |
1 |
|
735i -308 |
Left Handle Bar |
1 |
|
735i -310 |
Right Protective Cover |
1 |
|
735i -311 |
Left Protective Cover |
1 |
|
|
|
Hardware Kit |
|
735i -303 |
M8x15mm Bolt |
14 |
|
735i -304 |
M8 Curve Washer |
14 |
|
735i -305 |
M4x15mm Bolt |
2 |
|
735i -306 |
M6x15mm Bolt |
2 |
|
735i -312 |
M6x65mm Bolt |
2 |
|
A |
5mm Allen Key |
1 |
|
B |
6mm Allen Key |
1 |
|
735i -209 |
Safety Key |
1 |
|
C |
Silicone Lubricant |
1 |
|
735i -309 |
End cap |
4 |
|
735i -313 |
M4x10mm Bolt |
4 |
A1 |
A2 |
302 |
301 |
308 |
307 |
|
311 |
310 |
303 |
|
304 |
|
305 |
|
306 |
312 |
|
A |
|
B |
|
209 |
C |
|
309 |
|
313 |
Millimeters
8 735i TREADMILL
|
Item No. |
Description |
Qty. |
|
|||
|
735i -100 |
|
|
|
735i -101 |
Running deck frame |
1 |
|
735i -102 |
Front roller |
1 |
|
735i -103 |
Rubber cushion |
8 |
|
735i -104 |
Running deck |
1 |
|
735i -105 |
Running belt |
1 |
|
735i -106 |
Rear roller |
1 |
|
735i -107 |
Motor control board |
1 |
|
735i -108 |
Upper motor cover |
1 |
|
735i -109 |
Fixing bracket, motor |
1 |
|
735i -110 |
Bolt M4*15mm |
2 |
|
735i -111 |
Front mobile wheel |
2 |
|
735i -112 |
Bolt M4*10mm |
8 |
|
735i -113 |
Base frame |
1 |
|
735i -114 |
Speed sensor |
1 |
|
735i -115 |
On-off switch |
1 |
|
735i -116 |
Bolt M8*30mm |
2 |
|
735i -117 |
Power breaker |
1 |
|
735i -118 |
End cap-2 |
2 |
|
735i -119 |
Running deck frame end cap |
2 |
|
735i -120 |
Spring washer M8 |
2 |
|
735i -121 |
Drive belt |
1 |
|
735i -122 |
Left roller cover |
1 |
|
735i -123 |
Right roller cover |
1 |
|
735i -124 |
Side rein |
2 |
|
735i -125 |
Stud-1 |
2 |
|
735i -126 |
Washer, stud |
2 |
|
735i -127 |
Bolt M8*15mm |
2 |
|
735i -128 |
Bushing |
4 |
|
735i -129 |
Lower locking tube |
1 |
|
735i -130 |
Upper locking tube |
1 |
|
735i -131 |
Lower motor cover |
1 |
|
735i -132 |
Rear wheel |
2 |
|
735i -133 |
Spacer |
2 |
|
735i -134 |
Incline motor |
1 |
|
735i -135 |
DC motor |
1 |
|
735i -136 |
Lift arm |
1 |
|
735i -137 |
Adjustment pad |
2 |
|
735i -138 |
Bolt M8*15mm |
2 |
|
735i -139 |
Bolt M3*6mm |
2 |
|
735i -140 |
Bolt M8*40mm |
2 |
|
|
|
|
|
www.smoothfitness.com |
9 |
||
|
|
|
COMPLETE PARTS LIST |
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
tem No. |
Description |
|
Qty. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
735i -141 |
Bolt M8*40mm |
|
3 |
|
|
|
|
|
735i -142 |
Nut M8 |
|
2 |
|
|
|
|
|
735i -143 |
Bolt M10*45mm |
|
1 |
|
|
|
|
|
735i -144 |
Nut M10 |
|
1 |
|
|
|
|
|
735i -145 |
Spring washer M8 |
|
5 |
|
|
|
|
|
735i -146 |
Bolt M8*15mm |
|
2 |
|
|
|
|
|
735i -147 |
Horizontal adjustment |
|
2 |
|
|
|
|
|
735i -148 |
Bolt M8*140mm |
|
1 |
|
|
|
|
|
735i -149 |
Nut M8 |
|
5 |
|
|
|
|
|
735i -150 |
Bolt 5/16"*135mm |
|
1 |
|
|
|
|
|
735i -151 |
Lower console wire |
|
1 |
|
|
|
|
|
735i -152 |
Spring washer M8 |
|
1 |
|
|
|
|
|
735i -153 |
Bolt M4*10mm-1 |
|
8 |
|
|
|
|
|
735i -154 |
Bolt M4*10mm-2 |
|
4 |
|
|
|
|
|
735i -155 |
Power cord |
|
1 |
|
|
|
|
|
735i -156 |
Washer, stud |
|
2 |
|
|
|
|
|
735i -157 |
Bolt M8*40mm |
|
2 |
|
|
|
|
|
735i -158 |
Bolt M8*70mm |
|
3 |
|
|
|
|
|
735i -159 |
Electric wire cover |
|
1 |
|
|
|
|
|
735i -160 |
Stud-2 |
|
2 |
|
|
|
|
|
735i -161 |
Wire clip |
|
4 |
|
|
|
|
|
735i -162 |
Bolt M5*12mm |
|
4 |
|
|
|
|
|
735i -163 |
Air shock |
|
1 |
|
|
|
|
|
735i -164 |
Bolt M8*15mm |
|
2 |
|
|
|
|
|
735i -165 |
Bolt M8*55mm |
|
1 |
|
|
|
|
|
735i -166 |
Bolt M8*60mm |
|
1 |
|
|
|
|
|
735i -167 |
Adaptor |
|
1 |
|
|
|
|
|
|
|
|
|
|
|
10 735i TREADMILL
|
Item No. |
Description |
Qty. |
|
|||
|
|
|
|
|
735i -200 |
|
|
|
735i -201 |
Console frame |
1 |
|
735i -202 |
Console housing |
1 |
|
735i -203 |
Bolt M4*10mm |
6 |
|
735i -204 |
Handle pulse sensor |
2 |
|
735i -205 |
Bolt M4*25mm |
2 |
|
735i -206 |
IHP |
1 |
|
735i -207 |
Console cover |
1 |
|
735i -208 |
Tablet Shelf |
1 |
|
735i -209 |
Ring core |
1 |
|
735i -210 |
Safety key |
1 |
|
735i -211 |
Bolt M3*8mm |
18 |
|
735i -212 |
Operational button & overlay |
1set |
|
735i -213 |
Audio jack |
1 |
|
735i -214 |
Panel, console |
1 |
|
735i -215 |
Bolt M3*6mm |
13 |
|
735i -216 |
Bolt M4*10mm |
4 |
|
735i -217 |
Speaker |
2 |
|
735i -218 |
Speaker fixer |
2 |
|
735i -219 |
Handle grip foam |
2 |
|
735i -220 |
Handle button cover |
2 |
|
735i -221 |
Bolt M4*12mm |
4 |
|
735i -222 |
Safety key base |
1 |
|
735i -223 |
Bolt M3*6mm |
4 |
|
735i -224 |
Lower console cover |
1 |
|
735i -225 |
Bottle Holder |
1 |
|
735i -226 |
Bolt M3*6mm |
2 |
|
735i -227 |
Bolt M4*12mm |
14 |
|
735i -228 |
Bolt M3*10mm |
2 |
|
735i -229 |
Console wire |
1 |
|
735i -230 |
USB charger |
1 |
|
735i -231 |
Handle button sticker |
2 |
|
735i -232 |
Hand pulse wire |
1 |
|
735i -233 |
Handle button wire |
2 |
|
735i -234 |
Receiver wire |
1 |
|
735i -235 |
Receiver |
1 |
|
735i -236 |
Software update cap |
1 |
|
735i -237 |
- |
- |
|
735i -238 |
Tablet left support |
1 |
|
735i -239 |
Table right support |
1 |
|
735i -240 |
Spring |
2 |
|
735i -241 |
M4 washer |
2 |
|
735i -242 |
Washer |
2 |
|
735i -243 |
Bolt M2.6*8mm |
2 |
|
735i -244 |
Adaptor wire |
1 |
|
|
|
|
|
www.smoothfitness.com |
11 |
||
|
|
|
COMPLETE PARTS LIST |
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
Item No. |
Description |
|
Qty. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
735i -300 |
|
|
|
|
|
|
|
|
735i -301 |
Right upright |
|
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
735i -302 |
Left upright |
|
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
735i -303 |
Bolt M8*15mm |
|
14 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
735i -304 |
M8 curve washer |
|
14 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
735i -305 |
Bolt M4*15mm |
|
2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
735i -306 |
Bolt M6*15mm |
|
2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
735i -307 |
Right handle bar |
|
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
735i -308 |
Left handle bar |
|
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
735i -309 |
End cap |
|
4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
735i -310 |
Right protective cover |
|
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
735i -311 |
Left protective cover |
|
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
735i -312 |
Bolt M6*65mm |
|
2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
735i -313 |
Bolt M4*10mm |
|
4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
735i -400 |
|
|
|
|
|
|
|
|
735i -401 |
Fan |
|
1 |
|
|
|
|
|
735i -402 |
Fan cover |
|
1 |
|
|
|
|
|
735i -403 |
Bolt M3*30mm |
|
4 |
|
|
|
|
|
735i -404 |
Bolt M3*8mm |
|
4 |
|
|
|
|
|
|
|
|
|
|
|
12 735i TREADMILL
MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED
www.smoothfitness.com 13
MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED.