USER’S MANUAL
5.15P MOTORIZED TREADMILL
MODEL NUMBER: 5.15P
USER WEIGHT LIMITATION: 275lbs.
TOLL FREE CUSTOMER SERVICE NUMBER: 1.888.800.1167
SERIAL NUMBER (found on frame):
2
SMOOTH 5.15P MOTORIZED TREADMILL
PRECAUTIONS
For future service or related questions:
Please staple your receipt and/or write in the name and phone number of the retail store where you purchased your Smooth Fitness treadmill.
Name: ______________________________ Phone Number: ___________________ Receipt: ______________________
Precautions:
WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read the following important precautions and information before operating the treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of all warnings and precautions.
?Use the treadmill only as described in this manual.
?Place on a level surface, with 6 feet (2 m) of clearance behind it. Do not place the treadmill on any surface that blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill.
?When choosing a location for the treadmill make sure that the location and position permit access to a plug.
?Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a garage or covered patio, or near water.
?Do not operate the treadmill where aerosol products are used or where oxygen is being administered.
?Keep children under the age of 12 and pets away from the treadmill at all times.
?The treadmill should not be used by persons weighing more than 275lbs.
?Never allow more than one person on the treadmill at a time. Wear appropriate exercise clothing when using the treadmill. Do not wear loose clothing that could become caught in the treadmill. Athletic support clothes are recommended for both men and women. Always wear athletic shoes. Never use the treadmill with bare feet, wearing only stockings, or in sandals.
?When connecting the power cord, plug the power cord into a grounded circuit. No other appliance should be on the same circuit.
?Always straddle the belt and allow it to start moving before stepping onto the belt.
?Always examine your treadmill before using to ensure all parts are in working order.
?Allow the belt to fully stop before dismounting.
?Never insert any object or body parts into any opening.
?Follow the safety information in regards to plugging in your treadmill.
?Keep the power cord away from the incline wheels and do not run the power cord underneath your treadmill. Do not operate the treadmill with a damaged or frayed power cord.
?Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be performed by an authorized service representative, unless authorized and/or instructed by the manufacturer. Failure to follow these instructions will void the treadmill warranty.
?Never leave the treadmill unattended while it is running.
Visit us at: www.smoothfitness.com
3
SMOOTH 5.15P MOTORIZED TREADMILL
POWER REQUIREMENTS
Power Requirements:
IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN A RISK OF AN ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE PRODUCT IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILL NOT FIT THE OUTLET; HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.
This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes, surges and noise interference can result from weather conditions or from other appliances being turned on or off. To reduce the possibility of treadmill damage, always use a surge protector (not included) with your treadmill.
Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge protector with a UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltage rating of 400V or less and an electrical rating 120VAC, 15 amps.
This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance for electric current, should the treadmill malfunction. This treadmill comes with an electrical cord having an equipment-grounding conductor and a grounding plug. Always plug the power cord into a surge protector, and plug the surge protector into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in the drawing below.
Visit us at: www.smoothfitness.com
4
SMOOTH 5.15P MOTORIZED TREADMILL
PREASSEMBLY
Open the boxes:
You are now ready to open the boxes of your new equipment. Make sure to inventory all of the parts that are included in the boxes. Check the Hardware Comparison Chart for a full count of the number of parts included for this product to be assembled properly. If you are missing any parts or have any assembly questions call your local Smooth Retailer.
Gather your tools:
Before starting the assembly of your unit, make sure that you have gathered all the necessary tools you may require to assemble the unit properly. Having all of the necessary equipment at hand will save time and make the assembly quick and hassle-free.
Clear your work area:
Make sure that you have cleared away a large enough space to properly assemble the unit. Make sure the space is free from anything that may cause injury during assembly. After the unit is fully assembled, make sure there is a comfortable amount of free area around the unit for unobstructed operation.
Invite a friend:
Some of the assembly steps may require heavy lifting. It is recommended that you obtain the assistance of another person when assembling this product.
User Weight Limitation:
Please note that there is a weight limitation for this product. If you weigh more than 275lbs. it is not recommended that you use this product. Serious injury may occur if the user’s weight exceeds the limit shown here. This product is not intended to support users whose weight exceeds this limit.
Visit us at: www.smoothfitness.com
5
SMOOTH 5.15P MOTORIZED TREADMILL
HARDWARE COMPARISON CHART
Hardware chart:
For your convenience, we have identified the hardware used in the assembly of this product. This chart is provided to help you identify those items that may be unfamiliar to you.
NO. |
DESCRIPTION |
QTY. |
|
|
|
29 |
M5 x 14mm Bolt |
2 |
73 |
8mm Washer |
4 |
76 |
M10 x 26mm Bolt |
2 |
77 |
M8 x 18mm Bolt |
4 |
80 |
Plastic Cover |
2 |
81 |
M6 x 15mm Bolt |
1 |
87 |
M3.5 x 16mm Screw |
2 |
89 |
10mm Washer |
2 |
|
M4 x 15mm Reading Rack |
|
99 |
Screw |
3 |
|
Console Support Locating |
|
101 |
Screw |
1 |
MILLIMETERS
Visit us at: www.smoothfitness.com
6
SMOOTH 5.15P MOTORIZED TREADMILL
PARTS LIST
No. |
Description |
Qty. |
Order No. |
|
|
||||
1 |
Running Belt |
1 |
5.15P-01 |
|
2 |
Motor Hood |
1 |
5.15P-02 |
|
3 |
Deck Rear End Cap-Right |
1 |
5.15P-03 |
|
4 |
Deck Rear End Cap-Left |
1 |
5.15P-04 |
|
5 |
Side Rail-Right |
1 |
5.15P-05 |
|
6 |
Side Rail-Left |
1 |
5.15P-06 |
|
7 |
Front Roller |
1 |
5.15P-07 |
|
8 |
Front Roller Shaft |
1 |
5.15P-08 |
|
9 |
Rear Roller |
1 |
5.15P-09 |
|
10 |
Rear Roller Shaft |
1 |
5.15P-10 |
|
11 |
Running Deck |
1 |
5.15P-11 |
|
12 |
Base Frame |
1 |
5.15P-12 |
|
13 |
Handle Upright-Right |
1 |
5.15P-13 |
|
14 |
Handle Upright-Left |
1 |
5.15P-14 |
|
15 |
Main Frame |
1 |
5.15P-15 |
|
16 |
Elevation Support |
1 |
5.15P-16 |
|
17 |
Motor Control Board |
1 |
5.15P-17 |
|
18 |
Driving DC Motor |
1 |
5.15P-18 |
|
19 |
Motor Drive Belt |
1 |
5.15P-19 |
|
20 |
Motor Holder |
1 |
5.15P-20 |
|
21 |
Elevation Motor |
1 |
5.15P-21 |
|
22 |
Motor Bottom Tray |
1 |
5.15P-22 |
|
23 |
Handlebar-Right |
1 |
5.15P-23 |
|
24 |
Handlebar-Left |
1 |
5.15P-24 |
|
25 |
Hand Pulse Sensors |
2 |
5.15P-25 |
|
26 |
Console |
1 |
5.15P-26 |
|
27 |
Reading Rack |
1 |
5.15P-27 |
|
28 |
Console Support |
1 |
5.15P-28 |
|
29 |
M5 x 14mm Bolt |
2 |
5.15P-29 |
|
|
|
|
|
|
|
No. |
Description |
Qty. |
Order No. |
|
||||
|
30 |
Motor Hood Side Cover |
4 |
5.15P-30 |
|
Screw |
|||
|
31 |
Rear Wheel |
2 |
5.15P-31 |
|
32 |
Handlebar End Cap (Right & |
2 |
5.15P-32 |
|
Left) |
|||
|
33 |
(Pre-Assembled) |
|
5.15P-33 |
|
34 |
Safety Key |
1 |
5.15P-34 |
|
35 |
Motor Hood Side Cover- |
1 |
5.15P-35 |
|
Right |
|||
|
36 |
Motor Hood Side Cover-Left |
1 |
5.15P-36 |
|
37 |
Side Rail Guide Screw |
12 |
5.15P-37 |
|
38 |
Side Rail Guide |
6 |
5.15P-38 |
|
39 |
Deck Rubber Cushion Bolt |
8 |
5.15P-39 |
|
40 |
Deck Rubber Cushion |
8 |
5.15P-40 |
|
41 |
Motor Adjustment Bolt |
1 |
5.15P-41 |
|
42 |
8 x 23mm Washer |
2 |
5.15P-42 |
|
43 |
Motor Bumper Bushing |
1 |
5.15P-43 |
|
44 |
M10 x 116mm Bolt |
1 |
5.15P-44 |
|
45 |
Nut |
1 |
5.15P-45 |
|
46 |
M8 x 12mm Socket Bolt |
2 |
5.15P-46 |
|
47 |
8 x 16mm Washer |
2 |
5.15P-47 |
|
48 |
10 x 23mm Washer |
1 |
5.15P-48 |
|
49 |
Nut |
1 |
5.15P-49 |
|
50 |
Shock |
1 |
5.15P-50 |
|
51 |
Roller |
2 |
5.15P-51 |
|
52 |
Plastic Clamp-Top |
2 |
5.15P-52 |
|
53 |
Plastic Clamp-Bottom |
2 |
5.15P-53 |
|
54 |
Support |
2 |
5.15P-54 |
|
55 |
(Pre-Assembled) |
|
5.15P-55 |
|
56 |
U Bracket |
1 |
5.15P-56 |
|
57 |
Bumper |
1 |
5.15P-57 |
|
58 |
M16 x 54mm Bolt |
1 |
5.15P-58 |
|
|
|
|
|
Visit us at: www.smoothfitness.com
7
SMOOTH 5.15P MOTORIZED TREADMILL
PARTS LIST
No. |
Description |
Qty. |
Order No. |
|
|
||||
59 |
20 x 40mm Washer |
1 |
5.15P-59 |
|
60 |
M16 Nut |
1 |
5.15P-60 |
|
61 |
M10 x 67mm Bolt |
1 |
5.15P-61 |
|
62 |
M10 Nut |
5 |
5.15P-62 |
|
63 |
Bumper |
1 |
5.15P-63 |
|
64 |
Deck Rear End Cap Screw |
4 |
5.15P-64 |
|
65 |
Metal Plate |
2 |
5.15P-65 |
|
66 |
Rear Roller Washer |
2 |
5.15P-66 |
|
67 |
Rear Roller Bolt |
2 |
5.15P-67 |
|
68 |
Power Switch Board |
1 |
5.15P-68 |
|
69 |
Foot Up Lock |
1 |
5.15P-69 |
|
70 |
Caster Holder |
2 |
5.15P-70 |
|
71 |
Base Frame End Cap |
2 |
5.15P-71 |
|
72 |
Base Frame Rubber Cushion |
2 |
5.15P-72 |
|
73 |
8mm Washer |
10 |
5.15P-73 |
|
74 |
(Pre-Assembled) |
|
5.15P-74 |
|
75 |
M10 x 58mm Bolt |
4 |
5.15P-75 |
|
76 |
M10 x 26mm Bolt |
2 |
5.15P-76 |
|
77 |
M8 x 18mm Bolt |
6 |
5.15P-77 |
|
78 |
(Pre-Assembled) |
|
5.15P-78 |
|
79 |
M4 x 12mm Screw |
8 |
5.15P-79 |
|
80 |
Plastic Cover |
2 |
5.15P-80 |
|
81 |
M6 x 15mm Bolt |
2 |
5.15P-81 |
|
82 |
M10 x 20mm Bolt |
4 |
5.15P-82 |
|
83 |
M10 x 26mm Bolt |
2 |
5.15P-83 |
|
84 |
M8 x 45mm Bolt |
2 |
5.15P-84 |
|
85 |
M16 x 73mm Bolt |
2 |
5.15P-85 |
|
86 |
(Pre-Assembled) |
|
5.15P-86 |
|
87 |
M3.5 x 16mm Screw |
4 |
5.15P-87 |
|
88 |
Console Screw |
2 |
5.15P-88 |
|
|
|
|
|
|
|
No. |
Description |
Qty. |
Order No. |
|
||||
|
89 |
10mm Washer |
2 |
5.15P-89 |
|
90 |
6mm Washer |
2 |
5.15P-90 |
|
91 |
(Pre-Assembled) |
|
5.15P-91 |
|
92 |
16mm Washer |
2 |
5.15P-92 |
|
93 |
M8 Nut |
3 |
5.15P-93 |
|
94 |
Handlebar Front End Cap |
1 |
5.15P-94 |
|
Left-2 |
|||
|
95 |
Handlebar Front End Cap |
1 |
5.15P-95 |
|
Right-1 |
|||
|
96 |
Handlebar Front End Cap |
1 |
5.15P-96 |
|
Left-1 |
|||
|
97 |
Handlebar Front End Cap |
1 |
5.15P-97 |
|
Right-2 |
|||
|
98 |
M8 x 36mm Bolt |
2 |
5.15P-98 |
|
99 |
M4 x 15mm Screw |
3 |
5.15P-99 |
|
100 |
Console Bar End Cap |
2 |
5.15P-100 |
|
101 |
Console Support Locating |
1 |
5.15P-101 |
|
Screw |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Visit us at: www.smoothfitness.com
8
SMOOTH 5.15P MOTORIZED TREADMILL
PARTS DIAGRAM
A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PREASSEMBLED AT THE FACTORY. |
Visit us at: www.smoothfitness.com
Loading...