Sinbo SHC 4370 User Manual

SHC 4370 PROFESSIONAL HAIR&BEARD TRIMMER

INSTRUCTION MANUAL

EN

RU

ENGLISH

SINBO SHC 4370
PROFESSIONAL HAIR&BEARD TRIMMER
INSTRUCTION MANUAL

WARNING

- Cut off the power supply.
When it is to be serviced do remember to pull the power adaptor out, as it may cause
hazard of electrical shock.

- Wet hand prohibited.
Don’t pull the power adaptor with hand wet as it may cause hazard of electrical shock.

- No water threat.
Please don’t use it in bathroom as it may cause electrical shock.

- No disassembly.
Please don’t have this product modified disassembled or repaired at random, as it may
easily cause fire, electrical shock and injury etc.

- Don’t use it in
Keep the machine body and power adaptor away from water threat or don’t have it cleaned
by water, as it may cause hazard or electrical shock or short circuit.

- Charging

Don’t use it in power supply over 230V,as it may easily cause electrical shock and fire.

- Don’ts

Please don’t damage the cord, don’t have it machined, bended, stretched or twisted and
don’t place weight or extrusion upon power cord, as it may easily cause electrical shock
or fire. If the cord is damaged, it shall be replaced by an appointed servicing department
for the sake of safety.
When cord or power adaptor is damaged or when power receptacle is loosened please
don’t use it any longer as it may easily cause electrical shock short circuit or fire.

- Disposal of waste batteries

After batteries have been used up take them off and hand them over to an appointed
recovery point. Don’t throw them away at random.

TECHNICAL DATA

- Power: 3W

- Battery: 1XAA 800MA

- Rated Voltage: 220-240V 50/60HZ

- Adaptor output: 3V300MA

- Charging Time: about 8 hours

- Working time: 45mins

- 1 -

ATTENTION REMARKS

- To use it for the first time or when it has never been used for over half a year after
purchase. Please have it charged for 3 hours to activate the competence of batteries. If
it is charged when the secondary battery is completely discharged charging light may
not light on immediately, and will go to normal after several minutes.

- In order to better use hair clipper please drip oil onto blade. When the charge and use
the appliance the body will be heated is normal.

Attention: PLEASE DO NOT USE GASOLINE, ALCOHOL AND OTHER OIL.

- Keep away from water. Do not use near bathing pool, bathtub or other liquid container
with water.

- Charge the hair clipper at the temperature of 0˚C~35˚C. The parts of packing (plastic
bag, cardboard box, etc.).Must be kept out of reach of children. As they are possible
sources of danger.

BEFORE OPERATION

About length fixing accessories
1pcs cutting length comb. Hair length control, adjustable for cutting length from 3-15mm.
There are 2 piece combs, adjustable range for
A# is 0.5-9.5MM
B# is 10-20MM.
The minimum adjustable range is 0.5MM for each level.

1. To decide the length of cutting.

2. To select the suitable accessory for the length required. To keep it in alignment with

the blade.

3. Take off length fixing accessory. Push a side of the accessory by thumb to take it off.

Charging instructions

1. Place the switch to [O]. It is not allowed to charge when the switch is at [I].

2. Inset the coupler plug into the machine body.

3. Inset the power adaptor into the receptacle (the charging light will be

turned on).

HOW TO USE

To use it for the first time or when it has never been used for over half a year after
purchase, please have it charged for 3 hours to activate the competence of batteries. If
it is charged when the secondary battery is completely discharged, charging light may
not light on immediately, and will go to normal after several minutes.

When charging is finished:

1. Pull the power adaptor out of the receptacle.

2. Pull the coupler plug out of the machine body.

- Try to avoid continuous charging of long time (>20 hours)

- As it may shorten the service life of batteries.

- 2 -