Silvercrest WD1610 User Manual [pl, en, cs]
HOME TECH
Wireless Doorbell
GB
Wireless Doorbell
User manual and
service information
HU
Ajtócsengő
Felhasználói kézikönyv
és szerviz tájékoztatás
CZ
Bezdrátový zvonek
Uživatelská příručka a
informace o údržbě
SK
Zvoncek
Používateská príručka
a informácie o údržbe
HR
Radio-kontrolirano
kucno zvonce
Používateská príručka
a informácie o údržbe
PL
Dzwonek do drzwi sterowany radiowo
Instrukcja obsługi oraz
informacje o serwisie
SI
Daljinski zvonec
Navodila za uporabo in
servisne informacije
WD1610
Wireless Door Bell WD1610
Table of Contents
Package Contents .....................................................2
Important Safety Instructions..................................... 4
Introduction.............................................................. 13
Inserting the Batteries .........................................13
Batteries for the Receiver................................13
Battery for the Transmitter...............................14
Mounting the Devices..........................................15
Mounting the Transmitter.................................15
Mounting the Receiver.....................................16
Filling out the Name Label...................................17
Operation................................................................. 18
Selecting the Signalisation ..................................18
Selecting the Bell Melody ....................................19
Adjusting the Volume ..........................................19
Appendix..................................................................20
Technical Specifications......................................22
Warranty Information...........................................23
Declaration of Conformity.................................. 168
English - 1
Wireless Door Bell WD1610
Package Contents
- Receiver
- Transmitter
2 - English
Wireless Door Bell WD1610
Not illustrated:
- 3 AA-sized batteries
- 1 A23-sized battery
- 3 rawlplugs, 6mm
- 3 fixation screws
- 5 name labels
Description of figures:
1 Speaker
2 Melody selection button
3 Optical display
4 Mode selection switch
5 Volume selection switch
6 Bell button
7 Name label
8 Nose latch for upper housing piece
English - 3
Wireless Door Bell WD1610
Important Safety Instructions
Before you use this device for the first time,
please read the following notes in this manual
and heed all warnings, even if you are familiar
with handling electronic devices. Keep this
manual safe for future reference. If you sell the
device or pass it on, it is essential you hand
over this manual also.
This icon denotes important
information for the safe
operation of the product and for
4 - English
the user’s safety.
This symbol denotes further
information on the topic.
Wireless Door Bell WD1610
Children and Persons with
Disabilities
Electrical appliances do not belong in the
hands of children. People with disabilities
should only use electrical devices in
appropriate circumstances. Do not allow
children or persons with disabilities to use
electrical devices when not under supervision.
These may not comprehend the presence of
potential risks. Batteries and small parts
represent potential choking hazards. Keep the
batteries in a safe place. If a battery is
swallowed, seek medical help immediately.
Keep the packaging away from children and
persons with disabilities too. as there is danger
of suffocation.
English - 5
Wireless Door Bell WD1610
Batteries
Insert the batteries with the correct polarity.
Never try to recharge the batteries and under
no circumstances throw them into fire. Do not
short-circuit any batteries. Remove batteries
when the device is not to be used for a long
time. Non-intended use may cause explosion
and danger to life. Leaked batteries must be
handed in to a collection point for old batteries.
Make sure you wear protective clothing (such
as gloves) when manipulating leaked batteries.
6 - English
Wireless Door Bell WD1610
RF Interface
Place the device at least 20cm (8 inches) away
from pacemakers, as the RF signals may
interfere with the functionality of the
pacemaker. The transmitted RF signals can
cause interference with hearing aids. Do not
place the device with the wireless adapter
turned on near flammable gases or in an
explosion-sensitive area (e.g. a paint shop), as
the transmitted RF signals may cause
explosions or fire. The range of the radio wave
signals depends on environmental conditions.
English - 7
Wireless Door Bell WD1610
Operating Environment
The device is not for use in environments with
high temperatures or humidity (e.g.
bathrooms), and must be kept free of dust.
Operating temperature and operating humidity:
5°C to 40°C, max. 90% RH.
8 - English
Wireless Door Bell WD1610
Always make sure that:
- no direct heat sources (e.g. heating) can
affect the devices;
- no direct sunlight or artificial light reaches
the devices;
- the devices are never placed in the
immediate vicinity of magnetic fields (e.g.
loudspeakers);
- no fire sources (e.g. burning candles) are
placed on or near the devices;
- no foreign bodies are introduced into the
device;
- the devices should not be subject to any
sharp temperature changes;
- the devices are not subject to excessive
shocks and vibrations;
English - 9
Wireless Door Bell WD1610
Repair and Maintenance
Repairs are required when this device has
been damaged in any way, for example, when
liquid has entered the product, when the
product has been exposed to rain, when the
product does not work normally or if the
product has been dropped. If smoke, unusual
noises or smells are noticed, power off the
device immediately. In these cases the device
should not be used further and should be
inspected by authorized service personnel.
Please contact qualified personnel when repair
is needed. Never open the housing of the
device, or the accessories. Only use a clean,
dry cloth for cleaning. Never use any corrosive
liquids.
10 - English
Wireless Door Bell WD1610
Copyright
The entire content of this User’s Manual is
copyrighted and is provided to the reader for
information purposes only. Copying data and
information without the prior written and explicit
authorization from the author is strictly
forbidden. This also applies to any commercial
use of the contents and information. All texts
and figures are up-to-date as per the date of
print release. We assume no liability for any
changes.
English - 11
Wireless Door Bell WD1610
Conformity Notice
This product has been tested and
approved for compliance with the
basic and other relevant
requirements of the R&TTE Directive
1999/5/EC.
The corresponding Declaration of Conformity
can be found at the end of this User's Manual.
12 - English
Wireless Door Bell WD1610
Introduction
Thank you for purchasing this wireless door
bell.
This device allows you to quickly set up a bellring system. For instance, you can use it for the
front door of your home. There is no need for a
manual RF synchronisation between the
transmitter and the receiver.
Inserting the Batteries
Both devices are battery-powered. Insert the
supplied batteries into the devices.
Batteries for the Receiver
- Open the receiver’s battery compartment by
pushing the back panel cover in the
direction of the arrow mark.
- Insert the supplied batteries (size AA) into
the receiver. Make sure that the batteries
are properly aligned according to the
English - 13
Wireless Door Bell WD1610
polarity (+ and -). The correct polarity is
labelled on the batteries and inside the
battery compartment.
- Slide the battery compartment cover onto
the receiver housing.
Battery for the Transmitter
- To open the transmitter housing, use a flat
screwdriver. Insert the screwdriver carefully
into the transmitter housing side and press
it slightly inwards to release the nose latch
(8). Then pull the upper housing piece
upwards.
- Insert the supplied A23-sized 12 V battery
into the upper transmitter housing piece.
The correct polarity is labelled on the
battery and inside the transmitter housing.
- Replace the upper housing piece onto the
transmitter base unit.
You may also leave the base unit piece
separated if you want to mount the
transmitter on the wall.
14 - English
Wireless Door Bell WD1610
Mounting the Devices
The package includes all necessary material
for mounting both devices. Alternatively you
may simply leave the receiver for stand-up
installation.
Make sure that the distance between
transmitter and receive does not
exceed the maximum range. If
necessary, test their proper
functionality prior to mounting the
devices in their position.
Mounting the Transmitter
Look for a suitable place where you want to
mount the transmitter.
- Open the transmitter housing by inserting a
flat screwdriver into the notch on the
housing side. Carefully push the nose latch
(8) inwards. You can then remove the upper
housing piece.
English - 15
Wireless Door Bell WD1610
- Drill two 6mm holes at a distance of 50mm
in the wall.
- Insert two of the supplied rawlplugs into
these holes.
- Insert two of the supplied screws through
the holes located in the bottom piece of the
transmitter housing and then screw them
onto the rawlplugs.
- Replace the upper housing piece by
pushing it onto the base unit piece.
Mounting the Receiver
- Drill one 6mm hole at the desired position
on the wall.
- Insert one of the supplied rawlplugs into this
hole.
- Screw one of the supplied screws into the
rawlplug until its head is approx. 2mm away
from the wall.
- Place the receiver onto the screw head.
The wall-mounting hole located at the back
of the housing must completely fit over the
16 - English
Wireless Door Bell WD1610
screw head. By pulling it down carefully the
receiver clicks into place on the screw
head.
Filling out the Name Label
Remove the transparent plastic cover from the
receiver. Underneath you can write on the
name label (7). The package contains 5 labels
for future replacement. Replace the plastic
cover by pushing it onto the transmitter
housing.
English - 17
Wireless Door Bell WD1610
Operation
As soon as batteries are inserted into both
devices, they are ready for use. Press the bell
button (6) on the transmitter. The receiver
signalises either acoustically, optically or
acoustically and optically.
This allows you to customise the product
according to your needs.
Selecting the Signalisation
Slide the mode selector switch (4) to the
desired position.
Acoustic signal only
Optic and acoustic signals
Optic signal only
18 - English
Wireless Door Bell WD1610
Selecting the Bell Melody
Press the melody selection button (2) to listen
to the next available bell melody. Repeat this
process until you have found the desired
melody.
The last selected melody will be saved.
Adjusting the Volume
The volume selection switch lets you adjust the
volume on three levels.
Low volume
1
Middle volume
2
High volume
3
English - 19
Wireless Door Bell WD1610
Appendix
Disposal of Old Devices
Devices marked with this symbol are
subject to the European Directive
2002/96/EC.
All electric and electronic devices must be
disposed of separately from household waste
at established bodies. Avoid hazards to the
environment and dangers to your personal
health by disposing of the device properly. For
further information about proper disposal,
contact your local government, disposal bodies
or the shop where you bought the device.
Respect the environment. Old batteries do not
belong in with domestic waste. They must be
handed in to a collection point for old batteries.
Recycle the packaging material properly also.
Cardboard packaging can be taken to paper
20 - English
Wireless Door Bell WD1610
recycling containers or public collection points
for recycling. Any films or plastic contained in
the packaging should be taken to your public
collection points.
English - 21
Wireless Door Bell WD1610
Technical Specifications
Transmission
frequency
Range up to 100m (300ft)
Transmitter
Battery 1 battery 12V type A23
Dimensions 9.3 x 3.5 x 2.2 cm
Weight 31 g (without battery)
Receiver
Battery 3 batteries 1.5V type AA
Dimensions 11 x 7 x 3 cm
Weight 100 g (without batteries)
22 - English
433 MHz
depending on the
environment
(L x W x H)
(L x W x H)
Wireless Door Bell WD1610
Warranty Information
The guarantee period is for 3 years as of date
of purchase. For any guarantee claims, please
have your proof of purchase ready, and phone
our hotline:
TARGA GmbH
Postfach 22 44
D-59482 Soest
Germany
Phone: 0207-3650744
English - 23
Wireless Door Bell WD1610
24 - English
Bezprzewodowy dzwonek drzwiowy WD1610
Spis treści
Zawartość opakowania............................................26
Ważne instrukcje bezpieczeństwa...........................28
Wprowadzenie......................................................... 37
Wkładanie baterii.................................................37
Baterie przeznaczone dla odbiornika ..............37
Bateria przeznaczona dla nadajnika ...............38
Montaż urządzeń.................................................39
Montaż nadajnika ............................................39
Montaż odbiornika ........................................... 40
Wypełnianie etykiet .............................................41
Obsługa ...................................................................42
Wybór trybu sygnalizacji......................................42
Wybór melodii dzwonka.......................................43
Regulacja głośności ............................................43
Dodatek ...................................................................44
Dane techniczne..................................................46
Informacje o gwarancji ........................................47
Deklaracja zgodności ........................................168
Polski - 25
Bezprzewodowy dzwonek drzwiowy WD1610
Zawartość opakowania
- Odbiornik
- Nadajnik
26 - Polski
Bezprzewodowy dzwonek drzwiowy WD1610
Nie pokazano:
- 3 baterie typu AA
- 1 bateria typu A23
- 3 kołki rozporowe, 6 mm
- 3 wkręty mocujące
- 5 etykietek
Opis ilustracji:
1 Głośnik
2 Przycisk wyboru melodii
3 Sygnalizator optyczny
4 Przełącznik wyboru trybu
5 Przełącznik wyboru głośności
6 Przycisk dzwonka
7 Etykietka
8 Zatrzask górnej części obudowy
Polski - 27
Bezprzewodowy dzwonek drzwiowy WD1610
Ważne instrukcje
bezpieczeństwa
Przed pierwszym włączeniem urządzenia
należy przeczytać odpowiednie instrukcje
zawarte w niniejszym podręczniku i
zastosować się do ostrzeżeń. Dotyczy to
również osób, które mają duże doświadczenie
w korzystaniu z urządzeń elektronicznych.
Niniejszy podręcznik należy zachować do
przyszłego wykorzystania. W razie sprzedaży
lub odstąpienia urządzenia należy także
przekazać niniejszy podręcznik.
Tym symbolem oznaczone są
ważne informacje dotyczące
bezpiecznej obsługi urządzenia
oraz bezpieczeństwa
28 - Polski
użytkownika.
Bezprzewodowy dzwonek drzwiowy WD1610
Tym symbolem oznaczone są
dodatkowe informacje związane
z omawianym tematem.
Dzieci i osoby niepełnosprawne
Dzieciom nie wolno bawić się urządzeniami
elektrycznymi. Również osoby
niepełnosprawne powinny odpowiednio
posługiwać się urządzeniami elektrycznymi.
Dzieci oraz osoby niepełnosprawne nie mogą
używać urządzeń elektrycznych bez nadzoru.
Osoby te mogą nie zdawać sobie sprawy z
występowania potencjalnych zagrożeń.
Dziecko może udławić się w wyniku połknięcia
baterii lub innych małych części. Baterie należy
przechowywać w bezpiecznym miejscu. W
razie połknięcia baterii należy natychmiast
skontaktować się z lekarzem. Opakowanie
Polski - 29
Loading...