Silvercrest Dynamo Torch User Manual

Dynamo Stand Flashlight

Operating and Safety Instructions

10 - 15 m

50 000 h, 5 x 10 000 mcd

Version v2.15

IAN 61890

Safety Instructions

Before you use this device for the first time,
please read the following notes in this manual
and heed all warnings, even if you are familiar
with handling electronic devices. Keep this
manual safe for future reference. If you sell the
device or pass it on, it is essential you hand over
this manual also.

LED Radiation! Avoid harm to the eyes!
Never look into the LED beam. If you notice
any eye damage, consult a physician.

Never use any optical devices such as a lens
to look directly into the LED beam.

Electrical appliances do not belong in the
hands of children. Do not allow children to
use electrical devices when not under
supervision. Children may not comprehend
the presence of potential risks. Keep the
packaging away from children too as there is
danger of suffocation.

If smoke, unusual noises or smells are
noticed, power off the device immediately.
Do not breath in any smoke originating from
a device fire. In these cases the device
should not be used further and should be
inspected by authorized service personnel.

Make sure that the housings of the Dynamo
Stand Flashlight, of the charger and of the
car adapter do not become damaged. Stop
using the flashlight immediately if you find
any cables damaged.

The supplied devices do not contain any
parts that require user maintenance. Never
open the housings of the devices.

The supplied charger WJB-Y35120200D and
the supplied car charger must be used to
recharge the built-in battery of the Dynamo
Stand Flashlight only. The charger must not
be used for continuous power supply. Never
connect the charger to other devices. Only
use the supplied charger or the supplied car
adapter to recharge the built-in battery of
your Dynamo Stand Flashlight.

This Dynamo Stand Flashlight has not been
designed for use on vehicles. It must not be
used as a replacement for a bicycle or
motorbike headlamp.

Always make sure that:

 no direct heat sources (e.g. heating) can affect

the device;

 no direct sunlight or bright artificial light reaches

the device;

 contact with sprayed and dripping water and

abrasive liquids must be avoided and the
device should never be operated near water. It
must especially never be immersed.

 the device is not subject to excessive shocks

and vibrations;

Intended Use

The Dynamo Stand Flashlight can be used as a
mobile flashlight for hobbies, leisure or camping.
Thanks to the charging function via the dynamo
crank you may use the flashlight anytime without
the need of any external power supply. The
supplied charger allows you to recharge the built­in battery when a wall outlet is available. And the
car adapter lets you recharge the battery from
your vehicle. The flashlight can be placed upright
on its base and the magnetic side of its housing
allows it to be fixed to a metal surface. The
flashlight head can be turned through 180°.

This flashlight is not destined for commercial use.
The device fulfils all that relates to CE
Conformity, relevant norms and standards. Any
modifications to the equipment other than
recommended changes by the manufacturer may
result in these directives no longer being met.

Description

The items in the figure have the following
meaning:

[1] Dynamo Stand Flashlight

[2] Charger

[3] Car adapter (for 12V car battery)

[4] Rotating flashlight head

[5] On/Off pushbutton

[6] Magnetic surface

[7] Dynamo crank

[8] Charging indicator

[9] Indicator for full battery

[10] Receptacle for charger or car adapter

Technical Specifications

Dynamo Stand Flashlight

Lamps: 5 LEDs

Rechargeable
battery: Rechargeable NiMH battery

4.8V / 500 mAh

Dimensions: 21,7 x 9,4 x 8,8 cm

(L x W x H)

Weight: 410 g

Charger

Input voltage: 230V AC, 50 Hz

Output voltage: 12 V , 200 mA

Weight: 186 g

Car adapter

Operating voltage: 12 V

Fuse: 250 V / 2 A fast

Weight: 30 g

Getting Started

The Dynamo Stand Flashlight features a built-in
rechargeable battery. You can recharge it by
turning the dynamo crank in order to have the
flashlight immediately ready for use at any time.
Optionally you can recharge the built-in battery
with the supplied charger or the supplied car
adapter.

In order for the built-in rechargeable battery to
develop its full capacity, first execute an
extended charging cycle three times. To do this,
charge the battery for 16 hours and then fully
discharge it by using the flashlight. Repeat this
extended charging cycle at least two more times.

Charging via the Dynamo Crank

 Fold-out the dynamo crank [7].

 Turn the dynamo crank in any direction. In

order to obtain optimum charging, turn the
crank at a constant speed. During charging the
charge indicator [8] will light red.

Recharging the battery with the dynamo
crank can take a long time. You can stop
the charging process at any time.

The flashlight endurance varies depending
on the crank rotation time and the number
of LEDs switched on:

1 min. crank rotation =

max. 30 min. of light (1 LED)

max. 25 min. of light (3 LEDs)

max. 20 min. of light (5 LEDs)

Charging via the Charger

 Plug the small plug of the charger [2] into the

receptacle [10] of the dynamo flashlight.

 Plug the charger [2] into a wall outlet. During

charging the charge indicator [8] will light red.

 A full charging cycle for a completely

discharged battery takes at least 5 hours. The
charging process is completed when the
indicator [9] lights green. The Dynamo Stand
Flashlight is again ready for use. Then unplug
the charger [2] from the wall outlet.

- 1 -

Charging via the Car Adapter

Make sure that your vehicle has a 12V
battery. Never connect the car adapter to a
24V battery.

 Plug the small plug of the car adapter [3] into

the receptacle [10] of the dynamo flashlight.

 Then connect the car adapter [3] to a suitable

cigarette lighter in your car. During charging the
charge indicator [8] will light red.

 A full charging cycle for a completely

discharged battery takes at least 5 hours. The
charging process is completed when the
indicator [9] lights green. The Dynamo Stand
Flashlight is again ready for use. Then unplug
the car adapter [3] from the cigarette lighter.

Replacing the Fuse from the Car Adapter

The car adapter [3] has a small fuse. If the
charging indicator [8] suddenly stops lighting
when recharging the battery with the car adapter,
the fuse may be defective. Proceed as follows to
replace the fuse:

 Rotate the front cover counter-clockwise and

remove it from the car adapter.

 Remove the fuse. If required, replace the fuse

by a new one of the same type. Use a fast fuse
for 250 V / 2 A.

Normally, a defective fuse can be identified
by a broken wire inside the glass body.

Powering the Dynamo Stand Flashlight
On/Off

The Dynamo Stand Flashlight supports different
operating modes. This allows you to select
different levels of brightness. Press the On/Off
pushbutton [5] multiple times to toggle between
the following:

 1 LED on

 3 LEDs on

 All LEDs on

 Flashlight off

LED off

LED on

Press the On/Off pushbutton [5] once again to
toggle start the above cycle from the beginning.

The more LEDs you switch on, the faster the
built-in battery of your Dynamo Stand
Flashlight will discharge.

Cleaning

To clean the flashlight use a dry cloth. Never use
any solvents or cleaners that may damage the
plastic housing. Make sure that no liquid gets into
the housing. When very dirty, use a slightly
dampened cloth.

Disposal of Old Devices

Devices marked with this symbol are
subject to the European Directive
2002/96/EC. All electric and electronic

devices must be disposed of separately
from household waste at established bodies.
Avoid hazards to the environment and dangers to
your personal health by disposing of the device
properly. For further information about proper
disposal, contact your local government or
disposal bodies.

The built-in rechargeable battery cannot be
removed for disposal.

Declaration of Conformity

Targa GmbH, Lange Wende 41,
59494 Soest, Germany, declares that

this product complies with the basic
and other relevant requirements as well as with
the EMC Directive 2004/108/EC.

Warranty Information

The guarantee period is for 3 years as of date of
purchase. For any guarantee claims, please have
your proof of purchase ready, and phone our
hotline:

TARGA GmbH
Postfach 22 44
D-59482 Soest
Germany
Phone: [phone]

TARGA GmbH
Postfach 22 44
D-59482 Soest
Germany
Phone: [phone]