Details of Guarantee................................................................................ 50
4 - English
DV-5000HD Important Safety Instructions
Important Safety Instructions
Safety Instructions
Before you use this device for the first time, please read the following
notes in this manual and heed all warnings, even if you are familiar
with handling electronic devices. Always check that the product works
correctly.
Keep this manual with the instructions in a safe place for future
reference.
If you sell the device or pass it on, it is essential you hand over this
manual also.
Do not try to open the housing or reassemble the product. You are at
risk of receiving an electric shock. Maintenance and repairs should
only be carried out by qualified technicians.
Do not look at the sun or other sources of intense light. Doing so may
damage your eyesight.
Keep the device away from water and other liquids. Do not operate
the device with wet hands and do not use it in rain or snow.
Dampness can cause danger through fire or electric shock.
Keep the device out of the reach of children and animals to avoid
accidents or damage.
Switch the device off immediately if you notice it emitting smoke or
strange noises. Contact customer service. Never try to repair the
device yourself.
Only use the supplied charging cradle H-FUJ-FNP60-00 to recharge
the battery of the product.
Only use this device with the supplied rechargeable battery
(PAC NP60) in order to avoid overheating, deformation of the cover,
fire, electric shocks, explosion and other dangers.
Unplug the power cord from the mains outlet before you remove the
rechargeable batteries from the charger or separate the charger from
the power cord.
In the event of a defect in the product or its accessories, unplug the
power cord from the mains immediately.
English - 5
Important Safety Instructions DV-5000HD
Also, when there is the possibility of thunderstorms, unplug the power
cord from the wall outlet.
Never try to heat, disassemble or short-circuit the rechargeable
battery. Do not throw the rechargeable battery in fire.
Warning: Notice concerning separation from the mains
In order to completely disconnect the charger from the mains, unplug the
power cord from the wall outlet. The wall outlet where the device is
connected must be easy to access so that the power cord can be pulled
out quickly in case of emergency. Unplug the power cord from the mains
when you will not be using it for a long while (e.g. when going on holiday)
in order to avoid the danger of fire. Do not hold the power cord with wet
hands.
The device is not for use in rooms with a high temperature or humidity and
must be kept free of dust. Position the device on a stable, even surface
and do not place any objects on the device.
Always make sure that:
no direct heat sources (e.g. heating) can affect the device;
no direct sunlight or bright artificial light reaches the device;
contact with spray and dripping water and corrosive liquids must be
avoided and the device should never be operated near water, and it
must especially never be immersed (do not place any objects filled
with liquids such as vases or drinks near the device);
no fire sources (e.g. burning candles) are placed on or near the
device;
no foreign bodies are introduced into the device;
the device must not be subject to any great temperature changes as
this may cause moisture through condensation;
the device should not be subject to excessive shock and vibrations.
6 - English
DV-5000HD Important Safety Instructions
Children
Electrical appliances do not belong in the hands of children. Do not allow
children to use electrical devices when not under supervision. Children
may not comprehend the presence of potential risks. Rechargeable
batteries and small parts represent potential choking hazards. Keep
batteries out of reach of children. If a rechargeable battery is swallowed,
seek medical help immediately. Keep all packaging away from children as
this can cause suffocation.
Charger and Rechargeable Battery
Insert the rechargeable battery with the correct polarity. Never throw a
rechargeable battery into fire. Remove the rechargeable battery when the
device is not to be used for a long time.
Danger of Explosion!
Non-intended use may cause explosion and danger to life. Only replace
the rechargeable battery with an equivalent or a type recommended by the
manufacturer. Never replace any batteries in an explosion-sensitive
environment. While inserting or removing the batteries a spark may be
produced causing an explosion. Explosion-sensitive areas will normally
(but not always) be labelled. These include any fuel storage areas such as
below deck on a boat, fuel line or tank areas, environments where the air
contains inflammable substances (e.g. cereals, metal dust or powder, etc.)
and any areas where you should normally switch off your car engine.
Respect the environment. Old rechargeable batteries do not belong in with
domestic waste. They must be handed in to a collection point for old
batteries.
English - 7
Important Safety Instructions DV-5000HD
Cables
Always hold cables by the plug and never pull on the cable itself. Never
hold the power cord with wet hands as this may cause a short circuit or
electric shock. Never place the device, heavy objects or furniture on the
cable and take care that the cord does not become trapped, especially at
the plug and sockets. Never make knots in the cable and do not tie it
together with other cords. All cables should be positioned so that nobody
can trip over them or be obstructed by them. A damaged power cord can
cause a fire or an electric shock. Inspect the power cord from time to time.
Do not use any adapter plug or extension cable that does not meet the
required safety standards.
Maintenance and Care
Servicing is required when this device has been damaged in any way, for
example, when the charger or the housing of the DV-5000HD is damaged,
when liquid or objects have entered the device, when the product has
been exposed to rain or moisture, when the product does not work
normally or if the product has been dropped. If you notice any smoke,
unusual noise or strange smells, switch off the device immediately and pull
the power adapter out from the power supply. In this case the device
should not be used further and should be inspected by authorized service
personnel. Please contact qualified personnel when servicing is needed.
8 - English
DV-5000HD Important Safety Instructions
Intended Use
This is a consumer electronics device. It may only be used for private use,
not industrial or commercial purposes. In its default configuration, this
product has not been designed for medical, lifesaving, rescue or lifemaintaining purposes. Only connection cables and external devices may
be used that comply with safety standards and the electromagnetic
compatibility and shielding quality of this device.
This device fulfils all that relates to CE Conformity, relevant standards and
Directives. Any changes to the equipment other than the recommended
changes by the manufacturer may lead to the result that these directives
are not met any more. Only use the accessories recommended by the
manufacturer. If you are not using the device within the Republic of
Germany, you must observe the regulations and laws in the country of
use.
English - 9
Important Safety Instructions DV-5000HD
Conformity
This device and its supplied accessories have been tested
and approved for compliance with the basic and other
relevant requirements of the EMC Directive 2004/108/EC, as
well as the Low-voltage Directive 2006/95/EC.
Disposal of Old Devices
Devices marked with this symbol are subject to the European
Directive 2002/96/EC. All electric and electronic devices must
be disposed of separately from household waste at
established bodies.
Avoid hazards to the environment and dangers to your personal health by
disposing of the device properly. For further information about proper
disposal, contact your local government, disposal bodies or the shop
where you bought the device.
Respect the environment. Old rechargeable batteries do not belong in with
domestic waste. They must be handed in to a collection point for old
batteries.
toggle display view
10 PLAY button
11 Menu button
12 Mode selector
12 - English
DV-5000HD Introduction
Left Panel
13 Macro switch
14 Battery compartment
Right Panel
15 Retractile display
16 On/Off button (under the
retractile display)
17 Memory card
compartment (under the
retractile display)
English - 13
Introduction DV-5000HD
Top View
18 Microphone
19 Speaker
Bottom
20 Eyelet for carrying strap
21 Tripod mount
14 - English
DV-5000HD Introduction
Opening the Display
Open the display and then rotate so that the screen faces to the back
panel.
If required, you can also rotate the display so it faces to the front. In this
case, the picture orientation will be adjusted automatically.
English - 15
Introduction DV-5000HD
Getting started
The camcorder is powered by a rechargeable Lithium-Ion (PAC NP60)
battery. On delivery, the battery is not charged. Please charge the battery
before first use of the device.
Charging the Battery
Insert the rechargeable battery in the charger H-FUJ-FNP60-00 so that the
contacts [+] and [-] on the rechargeable battery and charger markings
match. Next connect the power cord to the charger and plug the power
cord to a wall outlet.
To operate the camera, only use the rechargeable LithiumIon battery PAC NP60.
Remove the rechargeable battery from the camera when
the device is not to be used for a long time.
During charging, the rechargeable battery and charging
device will become warm. This is not a malfunction.
16 - English
DV-5000HD Introduction
The status indicator of the charging cradle will light orange whilst the
battery is charging. When the charging process is completed, the status
indicator will light green. You can then insert the rechargeable battery into
the camcorder. Depending on the charge level, the charging cycle can
take up to 2 hours.
If, after inserting the rechargeable battery, the indicator
remains green, this means the rechargeable battery is
already charged or it is not correctly inserted. In this case,
check the polarity.
Inserting the Battery
When the battery is fully charged, insert it into the
camcorder as below. To do this, open the battery
compartment by gently pushing on the marking and
sliding it downwards.
Next insert the rechargeable battery with the correct polarity (see the
[+] and [-] icons on the battery and in the housing). Close the battery
compartment by placing the cover on it and sliding it upwards until it clicks
into place.
English - 17
Introduction DV-5000HD
Inserting an SD Card
By using the SD memory card (not included in the package) you can
increase the camcorder's storage capacity for saving your videos and
photos. When a memory card is inserted, all the recorded contents will be
saved onto it. If there is no memory card inserted, your photos and videos
will be saved to the internal memory of the camera.
Open the display and then open the memory card compartment by sliding
the cover into the direction of the arrow.
Then insert the memory card with the metal contacts facing forward into
the card slot. Slide it fully into the slot opening until the card clicks into
place. Close the memory card compartment by sliding the cover in the
opposite direction.
To remove the memory card, open the memory card compartment and
gently press on the inserted card. This will protrude a little so that you can
get a hold of it and remove it.
If the memory card or the internal memory is exhausted, the
message Memory full will appear on the display.
18 - English
DV-5000HD Introduction
Write-Protecting the Memory Card
The memory card features a write-protection tab. When the write
protection is enabled (see the right figure below) you will be able to view
existing videos and pictures only, but not be able to delete or edit them.
Also, it will not be possible to record any new videos or pictures onto the
memory card.
If you attempt to record a video or take a picture while the
write protection is enabled, when pressing the shutter button
the message Card locked will appear on the display.
Switching the Camcorder On and Off
Press the On/Off button [16] and keep it pressed down for approximately 1
second to turn the camcorder on in Recording mode.
Press the On/Off button [16] and keep it pressed down for approximately 1
second to turn the camcorder off.
English - 19
Introduction DV-5000HD
Switching the Operating Mode
Press the mode selector button [12] multiple times to toggle between the
modes Movie, Photo and Setup. With each press of the mode selector the
operating mode will change to the next mode.
Movie mode Photo mode Setup
Setting the Menu Language
Power the device on by pressing and holding the On/Off button [16]
for approx. 1 second.
Press the mode selector button [12] twice to display the Setup menu.
Press
press the shutter button [7].
Press
language and then press the shutter button [7].
Press the mode selector button [12] to exit the Setup menu.
or on the four-way button [6] to select Language and then
or on the four-way button [6] to select the desired display
20 - English
DV-5000HD Introduction
Setting Date and Time
Power the device on by pressing and holding the On/Off button [16]
for approx. 1 second.
Press the mode selector button [12] twice to display the Setup menu.
Press
then press the shutter button [7].
Press
month, day, hours and minutes fields.
Press the shutter button (7). The colour will change from yellow to red.
Press
for the current parameter. Then press the shutter button (7) again.
Repeat these steps until you have finished setting the date and time.
Navigate to the
settings and exit the menu.
or on the four-way button [6] to select Date / Time and
or on the four-way button (6) to toggle between the year,
or on the four-way button [6] to choose a different value
icon and press the shutter button [7] to save the
English - 21
Recording DV-5000HD
Recording
Recording Video Clips
Open the display and then rotate it according to your needs.
Power the camcorder on. If the current mode is not set to video
recording, select it by using the mode selector button [12].
Press the shutter button [7] to start recording. During recording the
power indicator [8] will blink red.
If necessary, use the zoom adjustment [9] to select a larger to smaller
scene area. Move the wheel upwards (T - Tele) to zoom in or move
the wheel downwards (W - Wide) to zoom out.
Press shutter button [7] to stop recording. The power indicator [8] will
light steadily green.
During recording, different icons may appear on the display informing you
about the current settings.
22 - English
DV-5000HD Recording
1
2
3
4
5
6
7
8
9
10
11
12
13
Zoom indicator
Exposure correction
Effect
Night Mode
White balance
Remaining memory available
Current memory type
Video lamp
Resolution
Battery status
Histogram display
Macro mode
Video mode
English - 23
Recording DV-5000HD
Capturing Pictures
Open the display and then rotate it according to your needs.
Power the camcorder on. If the current mode is not set to photo
capturing, select it by using the mode selector button [12].
If necessary, use the zoom adjustment [9] to select a larger to smaller
scene area. Move the wheel upwards (T - Tele) to zoom in or move
the wheel downwards (W - Wide) to zoom out.
Press the shutter button [7] to capture a picture. During saving the
power indicator [8] will light red.
The photo taken will be shown on the display for a few seconds. Then
the device returns to capture mode and the power indicator turns
green again.
In photo mode, different icons may appear on the display informing you
about the current settings.
24 - English
DV-5000HD Recording
0003
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Remaining number of shots
Exposure correction
Effect
Night Mode
White balance
Current memory type
Video light on
Resolution
Battery status
Histogram display
Macro mode
Self timer
Photo mode
Zoom indicator
English - 25
Recording DV-5000HD
The Video Light
In dark environments you can enable the built-in video lamp [2] for video
or photo recording. To do this, press the
[6]. Pressing this button again will turn the video lamp off. While the video
lamp is enabled, the
Video lamp
icon will appear on the display.
button on the four-way button
Exposure Compensation
During video and photo recording you can set an exposure compensation
value. Press the
compensation or press the
be shown on the display (icon 2)..
+2.0 EV
+1.5 EV
+1.0 EV
+0.5 EV
±0 EV No exposure correction.
-0.5 EV
-1.0 EV
-1.5 EV
-2.0 EV
button on the four-way button to reduce the exposure
button to increase it. The selected value will
Sensitive exposure setting.
Recommended for subjects in dark
environments.
Less sensitive exposure setting.
Recommended for bright subjects or for
backlight photography.
26 - English
DV-5000HD Recording
Histogram
The histogram is the graphical representation of the brightness distribution
of an image. If the graphic is accentuated on the left, the picture is very
dark; if it is accentuated on the right, the picture is very bright.
Dark picture Average picture Bright picture
You can optimise the brightness distribution before recording. If the picture
is too dark you can set a positive value for exposure correction. If the
picture is too bright you can set a negative value for exposure
compensation.
You can enable or disable the histogram display (see
page 35).
Macro Mode
This device features a macro function allowing you to focus on very close
subjects. This allows you to place the lens as close as 20cm (7.9inch)
from the subject. The macro switch [13] is located on the lateral panel of
the device.
Slide the switch to the Macro position to enable the macro mode. Slide the
switch back to the Normal position to disable the macro mode.
While the macro mode is enabled, the
icon will appear on the display.
English - 27
Recording DV-5000HD
Setting the Resolution
Before capturing videos or photos you can set the resolution by pressing
button located on the four-way button in video or photo mode.
the
In video mode, press this button multiple times to toggle cyclically between
CIF, 480P, 720P and 1080P resolution. The higher the resolution, the
higher the memory requirements for storing your recordings. The
designations have the following meanings:
Designation Format Resolution
CIF Default 352 x 240
480P Wide-screen 720 x 480
720P Wide-screen 1280 x 720
1080P Wide-screen 1440 x 1080
In photo mode, press this button multiple times to toggle cyclically
between 3M, 5M and 8M resolution. The higher the resolution, the higher
the memory requirements for storing your recordings. The designations
have the following meanings:
Designation Format Resolution
3M Default 2048 x 1536
5M Default 2592 x 1944
8M Default 3200 x 2400
When selecting 8M, the higher resolution will be obtained by
interpolation.
28 - English
DV-5000HD Playing Back
Playing Back
Depending on the selected mode you can use the Play button [10] to
switch to the corresponding playback mode.
Playing Back Video Clips
In video mode you can use the Play button [10] to switch to playback
mode. Press this button once again to return to video mode. The icon in
the upper-left corner of the display shows the current mode.
The following options are available:
Select a recorded content by pressing
[6].
To start or stop playback, press the shutter button [7].
To delete the currently displayed video, press the button on the
four-way button [6] (see page 34).
Press the Zoom adjustment [9] several times to select the desired
display mode With each press of the button the display will change to
Picture only
Picture with file information (not available for playback)
Help (not available for playback)
Standard mode
or on the four-way button
English - 29
Loading...
+ 75 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.