Please read the operating instructions and safety precautions carefully before use.
Explain the content and the hazards associated with using the phone to your children.
3
Remember to comply with legal
requirements and local
restrictions when using the
phone. For example in
aeroplanes, petrol stations,
hospitals or while driving.
Mobile phones can interfere
with the functioning of medical
devices such as hearing aids or
pacemakers. Keep at least
20 cm/9 inches between phone
and pacemaker. When using
the mobile phone hold it to the
ear which is further away from
the pacemaker. For more information consult your doctor.
The SIM card may be removed.
Caution! Small parts like this
could be swallowed by young
children.
The mains voltage specified on
the power supply unit (V) must
not be exceeded. Otherwise the
charging device may be
destroyed.
Emergency number(SOS)
By pressing the control key
§SOS, you can make an
emergency call on any network
without a SIM card and without
entering a PIN (not available in
all countries).
This must only be used in real
emergencies!
The ringtone (p. 62), info tones
(p. 63)and handsfree talking
are reproduced through the
loudspeaker. Do not hold the
phone to your ear when it rings
or when you have switched on
the handsfree function (p. 17).
Otherwise you risk serious
permanent damage to your
hearing.
Do not use an optical magnifier
to look at the activated infrared
interface [Class 1 LED product
(classification as per
IEC 60825-1)].
Only use original Siemens
batteries (100 % mercury-free)
and – charging devices.
Otherwise you risk serious
damage to health and property.
The battery could explode, for
instance.
You may only open the phone
tore place the battery (100 %
mercury-free) or SIM card. You
must not open the battery under
any circumstances. All other
changes to this device are
strictly prohibited and will
invalidate the guarantee.
4
Important:
Please dispose of unwanted
batteries and phones as
permitted by the laws in your
country.
The phone may cause
interference in the vicinity of TV
sets, radios and PCs.
Use only Siemens original
accessories. This will avoid
potential risks to health or
property and ensure compliance
with all relevant regulations.
Improper use will invalidate the guarantee!
Safety precautions
Overview of the phone
5
Loudspeaker
Display indicators
Signal strength/
GPRS available/
battery level.
A
Call key
Dial displayed phone
number or name, accept
calls.
In standby mode:
Display the last calls.
*
Hold down
In standby mode:
Switch signal tones on and
off (see also p. 86).
Microphone
On the underside.
Device interface
Connection for charger,
headset etc.
Control key at the top/at the
bottom
Press at the bottom: Open
Phonebook (in standby mode).
Hold down at the top: Start
voice dialling (in standby
mode).
Press at the top: Start volume
adjustment (during a call). Then
press at the top/at the bottom to
make your setting.
Scroll up and down in menus
and lists.
_ª g
Service provider
01.10.200212:30
Games...Menu
_ª g
Service provider
01.10.200212:30
Games...Menu
Integrated antenna
Do not interfere with the
phone above the battery
cover unnecessarily. This
reduces the signal strength.
B On/Off/End key
Press briefly:
End call/function or return
to standby mode. In menus:
one menu level back.
Hold down:
Switch phone on/off.
From menus: Return to the
standby mode.
#
Hold down
In standby mode: Switch
key lock on and off.
Control key on the left/on the right
Press the control key on the outside
left or right, to call up the function
that is displayed as text or icon on the
grey fields above the key. These are
in standby mode (factory default):
§Games...§ or e.g.
} (SIM services) and
§Menu§ (main menu).
6
The front and back covers of the casing (CLIPit™ Covers, my-CLIPit™: p. 14 and
p. 96) as well as the keypad can be changed in a matter of seconds - no tools
required. Please switch the phone off first:
Getting Started
To attach
To remove
Note
Your phone's display and the display cover of the top shell are delivered with a protective film.
Remove this film before getting started.
In rare cases the static discharge may cause discolouration at the edges of the display. However this will disappear within 10 minutes.
To avoid damaging the display the phone should not be used without the upper shell. Switch
off the phone before changing the upper shell.
Getting Started
7
Insert SIM card/battery
The service provider supplies you
with a SIM card on which all the important data for your line is stored. If
the SIM card has been delivered in
credit card size, snap the smaller
segment out and remove any rough
edges.
• Press grooved area
cover in the direction indicated by
the arrow
o
o
• Press latch in the direction indicated by the arrow
the cutout on the side of the
phone, then tilt upwards and remove
.
q
.
p
q
n, then lift
n
, lift battery at
p
• Insert SIM card in the opening,
contacts pointing downwards
(make sure the angled corner is in
correct position
until it engages
). Push gently
r
.
s
s
r
• Insert battery in the phone sideways
, then press downwards
t
until it engages
u.
u
t
• Replace cover and press downwards until it engages.
Note
Always switch off phone before removing
the battery!
Only 3-Volt SIM cards are supported.
Please contact your service provider if you
have an older card.
Functions without SIM card...............p. 88
8
Getting Started
Charge battery
The battery is not fully charged
when delivered. Plug in the charger
cable at the bottom of the phone,
plug in the power supply unit to the
mains power socket and charge for
least two hours.
hDisplay when charging is
in progress
Charging time
An empty battery is fully charged after about 2 hours. Charging is only
possible in an ambient temperature
of 5°C to 40°C (the charge icon flashes as a warning when the temperature is 5°C above/below this range).
The voltage specified on the power
supply unit must not be exceeded.
To use the full performance of the
battery, the battery must be fully
charged and discharged at least five
times.
Charge icon not visible
If the battery is totally discharged no
charge icon is displayed when the
charger is plugged in. It is displayed
after 2 hours at most. In this case
the battery is fully charged after
3-4 hours.
Only use the charger provided!
Display while in service
Charge level display during operation (empty-full):
adg
A beep sounds when the battery is
nearly empty. The charge level of the
battery is displayed correctly only after uninterrupted charging/discharging. You should not remove the battery unnecessarily and not end
charging prematurely, if possible.
Note
The charger heats up when used for long
periods. This is normal and not dangerous.
Operating times .................................p. 83
Quality declaration for the battery..... p. 84
General Instructions
9
User Guide
The following symbols are used to
explain operation:
Enter numbers or letters.
J
B
A
G
H
§Menu
L
On/Off/End key.
Call key.
Press control key at the top/at the bottom to scroll up
and down.
Press control key on the left/on the right to call a
function.
Displays a function.
Function depends on the
service provider, special
registration may be necessary.
Control key
Steps for calling a function are
shown in a condensed form in this user guide, e.g.: to display the call list
for missed calls:
§Menu§
KRecordsKMissed calls
This corresponds to:
n
§Menu§Open menu.
o
F
_g
Service provider
01.10.200212:30
Games...Menu
From standby mode: Press
control key on the right.
Phonebook
]
Messages
Records
Scroll to Records.
Press control key at the bottom to scroll downwards.
Select
10
General Instructions
p
§Select§Press.
q
§Select§Press.
Z Records
Press control key on the right
to open the Records submenu.
Missed calls
Calls received
Calls dialled
Press control key on the right
to open the list of Missed calls.
Messages
Groups
Select
Select
r
F
s
§View§Press.
+49892325678
Office
Carol
Scroll to the required
entry.
Press control key at the bottom to scroll downwards.
+49892325678
Office
Carol
Press control key on the left to
display the phone number with
date and time.
t
01.10.200212:30 1x
ViewOptions
ViewOptions
Office
+49322325774
CallOK
Switch on, off / PIN entry
11
Switch on/off
B
Hold down On/Off/End key
to switch on or off.
Enter PIN
The SIM card can be protected with a
4-8 digit PIN.
J
§OK§Press the control key on
Enter the PIN code using
the number keys (the display shows a series of asterisks, if you make a
mistake press §Clear§).
Enter PIN:
* * * *
ClearOK
ClearOK
the right to confirm the in-
put.
Logging on to the net-
work will take a few seconds.
Standby mode
_g
Service provider
01.10.200212:30
Games...Menu
When the name of the service provider/logo appears on the display,
the phone is in standby mode and
SIM card problems ............................ p. 85
Clear SIM card barring ...................... p. 13
Other network.................................... p. 74
Deactivate/activate screensaver .......p. 60
Set display contrast ...........................p. 61
Set time ............................................. p. 66
12
Security
ed against misuse by several security
codes.
Keep these confidential numbers in a
safe place where you can access them
again if required.
PIN
PIN2
PUK
PUK2
Phone
code
§Menu§
Protects your SIM card (personal identification number).
This is needed to set the charge
detail display and to access additional functions on special
SIM cards.
Key code. Used to unlock SIM
cards after the wrong PIN has
been entered.
Protects some functions of your
phone. Must be defined at the
first security setting.
KSetupKSecurity
Kthen select function
Codes
PIN control
The PIN is usually requested each
time the phone is switched on. You
can deactivate this feature but you
risk unauthorised use of the phone.
Some service providers do not permit deactivation of the control.
§Select§Press.
JEnter PIN.
§OK§Confirm input.
§Change§Press.
§OK§Confirm.
Change PIN
You can change the PIN to any
4-8 digit number you may find
easier to remember.
JEnter old PIN.
§OK§Press.
§OK§ Enter new PIN.
J
,
§OK§ Repeat new PIN.
J
,
Change PIN 2
(displayed only if PIN 2 is available).
Proceed as with Change PIN.
Security
13
ChangePhonecode
You define and enter the phone
code (4 - 8 digits) when calling a
phone code protected function
(e.g. babysitter, p. 20) for the first
time. It is then valid for all protected
functions.
If it is entered incorrectly three times
the phone is locked. Contact the Siemens Service (p. 92).
Clear SIM card barring
If the PIN is entered incorrectly three
times, the SIM card is barred. Enter
the PUK (MASTER PIN) provided by
your service provider with the SIM
card, according to instructions. If the
PUK (MASTER PIN) has been lost,
please contact your service provider.
If the called number is busy or cannot be reached because of network
problems several options are available (depending on the service provider). An incoming call or any other
use of the phone interrupts these
functions.
Either
Auto redial previous numbers
§Auto dial§ Press. The number is auto-
Or
Call back
§Call back§ Press. Your phone rings
Or
Reminder
§Prompt§Press. A beep reminds you
matically dialled for up to
15 minutes at increasing
intervals. End with:
B End key.
L
when the busy number is
free. Press the Call key to
dial the number.
to redial the displayed
phone number after
15 minutes.
Accept call
i
+498912345
ReplyReject
The phone must be switched on
(standby mode). An incoming call
will interrupt any other use of the
phone.
§Reply§Press.
Or
A Press.
If the phone number has been transmitted by the network, it is displayed. If the number and the name
are stored in the Phonebook, the corresponding name is displayed instead. If set, a picture or an animation can be displayed instead of the
bell icon (p. 24).
Note
Please make sure that you have accepted
the call before putting the telephone to your
ear. This will avoid damage to your hearing
caused by a loud ring tone.
Making a phone call
17
Reject call
§Reject§Press.
Or
BPress briefly.
Note
Missed calls............................... p. 29
Accept call using any key .................. p. 63
Handsfree
You can put the phone aside during
a call. You can then hear the caller
via the loudspeaker.
_g
vv
Carol
Handsfr.
§Handsfr.§ Activate handsfree
function.
§Yes§Activate.
_g
Handsfr.
< menu
< menu
§Handsfr.§ Deactivate.
Note
It is essential to switch off "Handsfree"
before putting the telephone directly to your
ear to avoid damage to hearing!
y menu§ Call menu ..........................p. 19
Held call
You can call another number during
a call.
y menu§ Open call menu.
HoldThe current call is put on
Now dial the new phone number
(also from Phonebook:
When the new connection is established:
y menu§ Open call menu
SwapSwap back and forth be-
hold.
_g
Call held
Back
F).
tween both calls.
G Control volume.
18
Making a phone call
Call waiting/Swap
You may need to register for this
function with the service provider
and set your phone accordingly
(p. 64).
During a call, you may be advised
that there is another call waiting.
You will hear a special tone during
the call. You have the following options:
L
Accept the waiting call
§Swap§Accept the waiting call
End the current call:
B
§Yes§Return to the held call.
Or
§No§The held call is ended.
and place the current call
on hold. To swap between the two calls, proceed as above.
Press. The following query is displayed: "Return to
the call on hold?"
Reject waiting call
§Reject§Reject the waiting call.
Or
§Divert§If this is set, the waiting
The caller hears the busy
tone.
call will be diverted to the
mailbox for example
(setting, p. 64).
End current call
B
§Reply§Accept the new call.
End the current call.
Making a phone call
19
Conference
Call up to 5 parties one by one and
link them together in a phone conference. Some of the functions described may not be supported by
your service provider or may have to
be enabled specially.
You have established a connection:
y menu§ Open menu and select
Hold. The current call is
put on hold. Now dial a
new number. When the
new connection is established ...
y menu§ ... open menu and select
Conference. The held call is
joined.
Repeat procedure until all participants are linked together (up to
5participants).
L
End
B
All calls in the conference
are ended simultaneously
when the End key is
pressed.
Call menu
The following functions are only
available during a call:
y menu§ Open menu.
Swap
Hold
Micro-
phone
Handsfree
Volume
Confe-
rence
Duration/
charges
Send
DTMF
tones
Call
transfer
L
Main menu
Call status
(p. 18)
(p. 18)
Switch microphone on/off. If
switched off, the person on
the other end of the line cannot hear you (muting).
Alternatively:
down.
(p. 17)
Adjust handset volume.
(p. 19)
While the connection continues, the call duration and (if
set, p. 30) the charge details
are displayed.
(p. 80)
The original call is joined to
the second one. For you,
both calls are now ended.
Access to the main menu.
List all held and active calls
(e.g. participants in a conference).
* Hold
20
Making a phone call
Babysitter
Only one phone number can be dialled.
D
Hold down control key on
the right.
Switch on
§Menu§KSetupKSecurity
KBabysitter
§Select§Press.
J
When first prompted you define and
enter the phone code (4 - 8 digits).
Please do not forget this code!
§OK§Confirm input.
§Change§ Press.
Enter phone code:
Q / JSelect phone number
from the Phonebook
(p. 21) or enter a new
one.
§OK§Confirm On.
Switch off
#Hold down.
JEnter phone code.
§OK§Confirm input.
§Change§ Press.
§OK§Confirm Off.
Note
Change phone code..........................p. 13
Phonebook
21
bers in the Phonebook with a special
name. To dial them, simply highlight
the name. If a phone number is
stored with a name, it appears on
the display when you are called. Entries that belong together can be
combined to form a group.
<New entry>
F
D
G
J
Number:
Enter phone number always with
prefix.
Name:
Enter (Text entry, p. 22).
Open Phonebook (in
standby mode).
<Own numbers>
<New entry>
<Group>
Select
Select <New entry>.
Activate input fields.
Make the following entries. The maximum
number of characters
available is shown at the
top of the display.
Group:
Default: No group
§Change§Entries can be organised
by groups (p. 26) for
example:
VIP, Leisure, Office, Family
Location:
Default: SIM
§Change§Select a storage location:
SIM, Protected SIM or Mobile
(p. 23).
Record no.:
Each entry is automatically assigned
a number under which it can also be
selected (p. 22).
Service numbers ............................... p. 84
Store control codes ...........................p. 80
22
Phonebook
Text entry
Press number key repeatedly until the required letter is displayed. The cursor advances after a short delay.
2
Ä, ä /1-9Umlauts and numbers are dis-
§Clear Press briefly to delete the let-
G
#
*
0
1
Press once for a, twice for b
etc. The first letter of a name is
automatically written in UPPERCASE.
Holddown: Writes the digit.
played after the relevant letters.
ter before the cursor.
Hold down to delete the whole
name.
Move the cursor (forward/
back).
Press briefly: Switch between: abc, Abc,T9abc,
T9
Abc, 123. Status indicator in
the top line of the display.
Hold down: All input modes
are displayed.
Press briefly: Select special
characters (p. 81).
Hold down: Open input menu
(p. 82).
Press once/repeatedly:
. , ? ! @ / & ~ + - :
Hold down: Write 0
Space. Only with T9: Press
twice = skip line.
Call/search for an entry
F
J
A
Open Phonebook.
/
Select a name with the
G
first letter and/or scroll.
Dial number.
Call with Record no.
A record number is automatically assigned to every new entry in the
Phonebook.
J
#
A
Enter record number (in
standby mode).
Press.
Press.
Edit entry
G
§Options§ Press and select Change.
G
J
§Save§Press.
Select entry in the Phonebook.
Select required input
field.
Make your changes.
Phonebook
23
Phonebook menu
§Options
View
Change
New
entry
Delete
Delete all
Voicedialling
Send
SMS...
Animation
Capacity
Open menu.
Display entry.
Display entry for changes.
Create a new Phonebook
entry.
Delete entry from the Phonebook.
Select storage location. Dele te
all entries after confirmation.
Use voice dialling to make an
entry (p. 25).
as entry: Send Phonebook
entry as vCard to recipient.
as text: Send entry as text of
an SMS message.
Assign an individual animation
to the phone number (p. 24).
Display the maximum memory
and the available capacity for
SIM, Protected SIM, phone
memory, animations and
voice dialling.
Location:
An entry can be moved to different
storage locations in the Phonebook
(change entry, p. 22).
SIM (standard)
Entries that are stored in the Phonebook on the SIM card can also be
used on a different GSM Phone.
Protected SIM ¡
Phone numbers can be stored in protected locations on a special SIM
card. A PIN 2 is needed for editing
(p. 12).
Mobile
Phonebook entries are stored in the
memory of the mobile phone when
the memory of the SIM card is full.
Symbols in the opened entry
¢,¡,
›
Å,Ã,Ä,Ç
°Voice dialling (p. 25)
¢
L
v
vStorage location (p. 23)
Picture (p. 24)
Groups (p. 26)
24
Phonebook
Assign animation
Assign an individual animation to
phone numbers. This animation will
appear in the display when there is a
call from this number.
Assign animation
F
G
§Options Open menu.
§Select§Select o Animation.
G
§Load§The previewp. 42 is
§Select§The animation is assigned
Open Phonebook.
Select entry.
Select Own animat. or
Own pictures.
Select Animation.
opened and the animation is displayed.
to the phone number. It
appears with a
in the Phonebook.
› symbol
Delete/change animation
If an animation is assigned to a
phone number, it can be deleted or
replaced.
G
§Options§ Press.
§Select§Select
§Delete The assignment is cleared
Or
§Select§The current animation is
Note
Animations can simply be pictures.
An animation can be assigned to several
phone numbers.
Add pictures/animations ....................p. 43
Siemens City Portal...........................p. 14
Select entry with anima-
›
tion
in the Phone-
book.
p Animation.
after confirmation.
displayed.
Phonebook
25
Voicedialling
You can dial phone numbers by simply saying a name.
Up to 20 voice recordings for voice
dialling or voice commands (p. 50)
can be stored in the phone (not on
the SIM card!).
Record recording
F
G
§Options§
Voicedialling
§Start§Start the recording.
A short signal sounds. Now say the
name and repeat it when prompted
by a signal tone and a display
prompt. A beep confirms the recording that is saved automatically.
°
Open Phonebook.
Select entry.
Open menu.
Select and confirm
with §Yes§.
Identification of entries
with voice dialling in the
Phonebook.
Apply voice dialling
E
Now say the name, the phone
number is dialled.
Note
Noisy environments may affect the recognisability.
Hold down. Start voice dialling (in standby mode).
Delete/redo recording
You can delete or redo the voice recording for a Phonebook entry.
F
G
§Options Open menu.
G
§Delete Press. Delete voice record-
Or
§Select§You can play back the re-
Open Phonebook.
Select entry with voice
dialling.
Select p Voicedialling.
ing with §Yes§. The Phonebook entry itself is not
affected.
cording or redo it.
26
it is best to assign them to a group,
e.g.: VIP, Leisure, Office, Family
§Menu§
KGroupsKSelect function:
Groups
SMS to group
A memo (SMS) can be sent as a "circular" to all members of a group.
Each SMS is charged separately!
G
§Select§Press. The group is con-
J
A
A
Select a group
(the number of the entries is listed behind the
group name).
Å VIP(6)
à Leisure(9)
ÄOffice(12)
Select
firmed and the editor is
opened.
Compose message.
Press. The first recipient is
displayed.
Press. The SMS is sent.
Each send operation must be confirmed. It is possible to skip individual recipients.
Call to group
You can call up to 5 group members
one by one and link them together in
a conference (function may need to
be enabled by the service provider).
G
§Select§Press. The members of
G
§Change§Press. Mark entry/unmark
Select a group.
the group are listed.
Select the entries you
want to call.
entry.
L
o Anne
p Barbara
p Carol
ChangeOK
Groups
27
§OK§Confirm selection. The
A
§Options
first entry is dialled. When
the connection has been
established, the call is put
on hold.
Proceed by calling the
next entry until all marked
entries are called (up to 5,
depending on the service
provider).
Open menu e.g. to link
the calls on hold in a con-
.
ference
à (2)
v
Barbara
Next: Carol
DialOptions
Call to group menu
§Options
Dial
Skip
Conference
Swap
Hold
Open menu.
Dial current entry.
Skip next number.
Link all calls on hold in a
conference (p. 19).
Accept the waiting call and
put the current call on hold
(p. 18).
Put call on hold to call another entry.
Microphone
Handsfree
Volume
Duration/
charges
Send DTMF
tones
Call transferL
Main menu
Call status
Switch the microphone on/
off. When this is switched
off the person on the other
end of the line cannot hear
you (muting).
Alternatively:
* Press down.
Call via the loudspeaker.
Adjust handset volume.
While the connection continues, the call duration and
(if set, p. 30) the call time/
cost are displayed.
(p. 80)
The original call is joined to
the second one. For you,
both calls are now ended.
Direct access to the main
menu.
List all held and active calls
(e.g., participants in a
conference).
28
Groups
Group setup
§Menu§KGroupsKGroup setup
Å VIP(6)
à Leisure(9)
ÄOffice(12)
RenameSelect
G
§Rename§ Change group name.
§Select§Display members of the
<New entry>
§View§Display entry.
§Options See below.
Select a group.
group.
<New entry>
Barbara
Carol
ViewOptions
Make your entries as in
Phonebook (p. 21).
Group entry menu
§Options
View
Change
New entry
Remove
Remove all
Voicedialling
Send SMS...
Animation
Open menu.
Display entry.
Open entry for changes.
Enter new member.
Remove entry only from the
group. It is still available in
the Phonebook.
Remove all entries from the
group.
Start voice dialling to an entry (p. 25).
as entry: Send Phonebook
entry to recipient.
as text: Send entry as text
of an SMS message.
Assign an individual animation to the phone number
(p. 24).
Records
29
bers of calls for convenient redialling.
§Menu§
KRecords
§Select§Press.
G Choose call list.
§Select§Press.
G Select phone number.
ADial phone number.
Or
§View§Display information on
The following call lists are available:
Missed calls
The phone numbers of calls
that you have received but not answered are stored for call back purposes.
Requirement: The network supports
the "Caller Identity" feature.
Calls received
All accepted calls are listed. Requirement:
The network supports the "Caller
Identity" feature.
the phone number.
L
Icon in standby mode for
missed call. When you
press the control key (on
the left), the phone
number is displayed.
L
Calls dialled
Access to the last ten numbers you
dialled.
A
Erase records
The contents of all call lists are
deleted.
Call list menu
The call list menu can be called up if
an entry is highlighted.