Siemens A30853 User Manual
27.11.98
s
bk_front.fm5
Profiset 30isdn engl.: A30853-X300-B107-1-7619
Profiset 30isdn
Operating instructions
Please read the safety precautions outlined in these operating
instructions before putting the telephone into service! (page V)
ACHTUNG! Schnittkante ggf. auf Titelseite U1 nach außen versetzen wg. Falz-Ausklappseite
27.11.98
kap00.fm5
Profiset 30isdn
Profiset 30isdn
Your guide to this manual
Profiset 30isdn engl.: A30853-X300-B107-1-7619
The first telephone call
Customising the telephone
Correcting functional defects
The fastest way to get up and running
Putting the telephone into operation
(➔ page 1).
Conducting a call (➔ page 9).
Defining telephone settings
(➔ page 27).
Programming keys (➔ page 25).
Information on the location of the
Profiset 30isdn (➔ page V).
Correcting defects (➔ page 45).
Brief instructions for the
Profiset 30isdn (➔ page 49).
II
27.11.98
kap00.fm5
Overview: Profiset 30isdn
Profiset 30isdn engl.: A30853-X300-B107-1-7619
Profiset 30isdn
15
14
16
17
18
19
20
1
Keypad
2
Loudspeaker key
3
Minus key
4
Plus key
5
Mute key
6
Number redial key
7
Consultation key
8
Locking key
9
Programming key
10
Disconnect key
189
11
Conference key
12
Callback key
13
Call forwarding key
14
Labelling card
15
Display
16
Destination dialling keys
17
Call list key
18
Speed dialling key
19
Loudspeaker
20
Handset
13
12
11
10
6
5
4
3
2
7
III
27.11.98
Profiset 30isdn
Overview: Keys
S
s
R
W
m
+
-
l
z
j
k
e
f
g
h
kap00.fm5
Programming key
To start or exit a programming procedure.
Locking key
To activate/deactivate the total lock.
To change the display for call numbers exceeding 12 digits.
Consultation key
To initiate a consultation. To toggle between two parties.
To accept a call in waiting. To terminate a three party conference.
Number redial key
To dial the number dialled last with the handset off-hook.
To view the number redial memory with the handset on-hook.
Mute key
To switch off the microphone.
Plus key
To increase the handset and loudspeaker volume during a call
(the setting applys to the current call).
Minus key
To lower the handset and loudspeaker volume during a call (the setting applys
to the current call). To delete the previous character, when entering numbers or
letters.
Loudspeaker key
To change over to open listening. To activate on-hook preparation of dialling.
Destination dialling keys
To dial a stored call number.
Call list key
To view the call list with the handset on-hook.
Speed dialling key
To dial a speed dialling number assigned to one of the digit keys.
Call forwarding key
To activate/deactivate call forwarding.
Callback key
To initiate/cancel callback.
Conference key
To set up/terminate a three-party conference.
Disconnect key
To reject an incoming call or a call in waiting. To disconnect one party (if there
are two calls in progress).To disconnect one party from a three-party conference. To cancel a programming procedure without making any changes.
Profiset 30isdn engl.: A30853-X300-B107-1-7619
IV
27.11.98
kap00.fm5
Safety precautions and approval
Safety precautions
The Profiset 30isdn complies with the European standard EN60
950, which deals with the safety of information technology
equipment including electrical business equipment.
This device has been designed with safety in mind, this protecting both individuals and objects.
For your safety and protection, the telephone must not be used
in bathrooms, etc. as it is not splashproof.
There is always the danger of small objects being swallowed by
young children. In the case of the Profiset 30isdn, this applies in
particular to the connecting cord clip.
Please make sure that such items are not accessible to children.
Location of the telephone
● The telephone should be operated in a controlled environ-
ment with an ambient temperature between + 5°C and
+ 40°C.
● Under normal circumstances, the rubber feet of the
telephone will not leave marks on the installation surface.
However, due to the vast array of surface finishes applied to
furniture, marks on the installation surface cannot be ruled
out. Place the unit on a smooth, non-slip surface.
● Do not install the telephone in a room where large quanti-
ties of dust accumulate; this can considerably reduce the
service life of the telephone.
● Do not expose the telephone to direct sunlight or any other
source of heat, as this is liable to damage the electronic
equipment and the plastic casing.
● Do not operate the telephone in damp environments such
as bathrooms.
● The power supply connector of the NTBA must be inserted.
Profiset 30isdn engl.: A30853-X300-B107-1-7619
Profiset 30isdn
V
27.11.98
kap00.fm5
Profiset 30isdn
Approval and conformity
Profiset 30isdn engl.: A30853-X300-B107-1-7619
Your Profiset 30isdn has a TYPE-EXAMINATION CERTIFICATE.
It has been certified in accordance with EU Guideline
91/263/EWG Telecommunication Terminals.
This telephone meets the requirements of the EU Guideline and
the national supplements to it in Germany.
It may thus be connected to and operated in any ISDN multi-
device connections and ISDN PBXs.
The equipment’s conformity to the above guidelines is
confirmed by the CE symbol.
Your Profiset 30isdn supports the extensive range of ISDN
services available. To find out which services are available to
you, contact your local network operator.
VI
27.11.98
profi30.IVZ
Profiset 30isdn engl.: A30853-X300-B107-1-7619
Contents
Profiset 30isdn .............................................................................................................................. II
Your guide to this manual .............................................................................................................. II
Overview: Profiset 30isdn ...............................................................................................................III
Overview: Keys ...............................................................................................................................IV
Safety precautions and approval ................................................................................................V
Safety precautions ......................................................................................................................... V
Location of the telephone .............................................................................................................. V
Approval and conformity .................................................................................................................VI
Putting the telephone into operation ........................................................................................ 1
Symbols used in these operating instructions ............................................................................... 1
Step 1: Check the contents of the package .....................................................................................2
Step 2: Connect the telephone ........................................................................................................3
Step 3: Entitle the device to operate in restricted powering conditions ........................................ 4
Step 4: Program the multiple subscriber numbers (MSNs) ........................................................... 4
Step 5: Setting the national variants ............................................................................................... 5
Step 6 (PBX operation only): Program the trunk code .................................................................... 5
Step 7: Try out the telephone ..........................................................................................................6
Display-driven telephone operation .......................................................................................... 7
Outgoing and incoming calls ...................................................................................................... 9
Calling users ................................................................................................................................... 9
On-hook dialling .............................................................................................................................. 9
Number redial (automatic dialling) ..................................................................................................10
Dialling call numbers using the Destination dialling keys (automatic dialling) .............................. 10
Dialling call numbers using the Speed dialling keys (automatic dialling) ...................................... 11
Accepting a call ..............................................................................................................................12
Rejecting a call (Disconnect) ........................................................................................................ 12
Call forwarding ............................................................................................................................. 12
Call waiting .....................................................................................................................................13
Deactivating the call signal (Do not disturb) ................................................................................. 13
Call list ............................................................................................................................................14
Callback ........................................................................................................................................ 15
Ending a call – disconnecting ....................................................................................................... 16
Convenient and secure telephone communication ................................................................ 17
Activating/deactivating open listening .......................................................................................... 17
Switching to mute (consultation in the room) .............................................................................. 17
Parking a call ..................................................................................................................................18
Resuming a parked call ................................................................................................................ 18
Locking your telephone ..................................................................................................................19
DTMF signalling .............................................................................................................................20
Keypad signalling .......................................................................................................................... 20
Overview: DTMF / keypad signalling ..............................................................................................21
Calls involving two or more parties ......................................................................................... 22
Calling the second party (consultation) ......................................................................................... 22
Switching between two calling parties (toggling) ......................................................................... 22
Disconnecting one party .............................................................................................................. 23
Three-party conference ................................................................................................................ 23
Ending a conference ......................................................................................................................24
Programming keys on the telephone ...................................................................................... 25
Programming the destination dialling keys ................................................................................... 25
Programming the speed dialling keys .......................................................................................... 25
Programming direct station selection (babyphone) ...................................................................... 26
VII
27.11.98
profi30.IVZ
Profiset 30isdn engl.: A30853-X300-B107-1-7619
Contents
Quick reference for available telephone settings ................................................................... 27
Programming the telephone settings ...................................................................................... 28
Password ..................................................................................................................................... 28
Ringer volume .............................................................................................................................. 29
Ringer melody .............................................................................................................................. 29
Handset and loudspeaker volume ................................................................................................ 30
Call processing type ..................................................................................................................... 30
Trunk code for operation at a PBX ............................................................................................... 31
Multiple Subscriber Numbers (MSN) ........................................................................................... 31
National variants ........................................................................................................................... 32
Signalling method to control the ISDN services .............................................................................33
Connection code for parking/resuming a call .................................................................................34
Date/time ..................................................................................................................................... 34
Call number for call forwarding unconditional .............................................................................. 34
Tariff unit factor ............................................................................................................................ 35
Activating/deactivating the display of charge/call time of the active call ...................................... 35
Activating/deactivating the display of charge/call time of the last outgoing call ........................... 36
Activating/deactivating the summation meter for charges .............................................................37
Clearing the summation meter ..................................................................................................... 37
Activating/deactivating the display of your own call number .........................................................38
Enabling/disabling call waiting ...................................................................................................... 38
Clearing memory ............................................................................................................................39
Checking the settings (status) ...................................................................................................... 39
Restoring the as-supplied condition ...............................................................................................40
Displaying the software version ................................................................................................... 40
Important information for installation and operation ............................................................ 41
Maintenance ................................................................................................................................ 41
Removing and inserting the labelling cards .................................................................................. 41
ISDN supplementary services ........................................................................................................42
Technical data .............................................................................................................................. 42
Default settings ............................................................................................................................ 42
Overview: Signal tones ..................................................................................................................43
Third party use/disposal ............................................................................................................... 43
Warranty .........................................................................................................................................44
Siemens Service .......................................................................................................................... 44
Procedure in the case of malfunctions ...........................................................................................45
ISDN glossary ............................................................................................................................. 46
Quick reference guide ............................................................................................................... 49
Quick reference for available telephone settings ................................................................... 50
Index ............................................................................................................................................ 51
VIII
27.11.98
kap01.fm5
Profiset 30isdn engl.: A30853-X300-B107-1-7619
Putting the telephone into operation
Putting the telephone into operation
Symbols used in these operating instructions
Press the appropriate key.
S
Enter the desired value using the digit keys.
T
In some cases display messages are provided. Example:
P
15000_
For information on display-driven operation of the Profiset
30isdn, see page 7.
Please read the ”Safety precautions and approval“ information at the front of these operating instructions before putting the telephone into operation!
Please follow the step-by-step instructions.
1
27.11.98
kap01.fm5
Putting the telephone into operation
Step 1: Check the contents of the package
The default package contains:
● 1 Profiset 30isdn,
● 1 Handset,
● 1 Handset cord (coiled),
● 1 ISDN connecting cord,
● 1 Operating instructions (not illustrated)
Profiset 30isdn engl.: A30853-X300-B107-1-7619
HandsetProfiset 30isdn
ISDN connecting cord
Handset cord (coiled)
2
27.11.98
kap01.fm5
Step 2: Connect the telephone
Telephone connecting cord
Profiset 30isdn engl.: A30853-X300-B107-1-7619
Putting the telephone into operation
To ISDN socket
Restricted powering switch
Handset cord (coiled)
Telephone connecting cord
Handset cord (coiled)
Both ends of the handset cord have the same connector.
Insert the connector at the long end of the handset cord
into the socket labelled a on the underside of the device and insert the other connector into the handset below the mouthpiece. In both cases, the connectors must
engage audibly. Feed the cable into the cable run.
Die Stecker müssen in beiden Fällen hörbar einrasten.
Both ends of the telephone connecting cord have the
same connector.
Insert one connector into the socket labelledAon the
underside of the device and insert the other connector
into your ISDN socket. In both cases, the connectors
must engage audibly. Feed the cable into the cable run.
3
27.11.98
P
P
P
kap01.fm5
Profiset 30isdn engl.: A30853-X300-B107-1-7619
Putting the telephone into operation
Note that the NTBA must be connected to the power grid.
The Profiset 30isdn takes the necessary power from this
NTBA.
In order to avoid unauthorized unplugging of the
telephone connecting cord from the telephone
socket, the plug is protected. Use a small
screwdriver or the like to unplug the connector.
Step 3: Entitle the device to operate in restricted powering conditions
The restricted powering switch is located on the underside of the device. The recessed sliding switch can be
moved with a screwdriver.
If the switch points to the symbol A , your telephone is
entitled to operate in restricted powering conditions that
means that the important telephone functions can still be
used.
If you connect more than one unit to your ISDN
connection, only one unit can be operated
during restricted powering. Mark this unit
accordingly!
Step 4: Program the multiple subscriber numbers (MSNs)
We recommend that you enter the MSNs when first
putting the telephone into operation, because only then
you can use all the functions of your telephone. The
MSNs (Multiple Subscriber Numbers) are the call
numbers you were assigned for your ISDN connection.
These numbers are entered as follows:
Display after connecting the telephone
S
01
Enter “1“ for MSN 1
T
Enter the MSN
T
4
00.00.00 00:00
a
Handset is on-hook.
01_
011_
33758_
The input of the first MSN is completed. Repeat these
S
steps for the second and third MSN.
27.11.98
P
P
P
P
kap01.fm5
Step 5: Setting the national variants
This setting takes account of specific national features of
the ISDN network:
a
Handset is on-hook
S
19
Enter the national variant,
T
e.g. “43“ for Austria
00.00.00 00:00
1949_
1943_
Profiset 30isdn engl.: A30853-X300-B107-1-7619
Putting the telephone into operation
It is not necessary to enter MSNs 2 and 3.
MSNs can be entered at any time (➔ page 31).
Please note htat the first MSN is also called global call number in Austria.
If more than one MSN is entered, take care that
this global call number will not be used. Otherwise all untis connected to his So bus will be
called.
Your Profiset 30isdn is preset to the national variant “49”
for Germany. (For further national variants ➔ page 32.)
The setting of the national variant is completed.
S
Step 6 (PBX operation only): Program the trunk code
If you are operating your Profiset 30isdn at a telecommunications system (private branch exchange), you must program a trunk code in accordance with the configuration of
the system (trunk code, max. 2 digits ➔ page 31) :
a
Handset is on-hook
S
24
Enter the trunk code e.g. “0“
T
00.00.00 00:00
24_
240_
The programming of the trunk code is completed.
S
You can cancel a programming procedure
without making any changes by pressing the
Disconnect key h!
5
27.11.98
kap01.fm5
Putting the telephone into operation
Step 7: Try out the telephone
You can now try out your Profiset 30isdn.
Calling another party:
c
Lift the handset.
Enter the call number.
T
The number is dialled.
Talk.
d
Taking a call:
Call signal is heard.
The calling party’s number is indicated on the display, if it
is known and call identification has not been barred.
c and d Lift the handset and talk.
Profiset 30isdn engl.: A30853-X300-B107-1-7619
The date and time are preset with zeros by default. The correct date and time are set automatically by the switching centre the first time an
outgoing call is set up. If your network operator
does not support this service, you can program
the date and time yourself (➔ page 34).
6
27.11.98
kap01.fm5
Display-driven telephone operation
Display-driven telephone operation
Your Profiset 30isdn has a one-line display that contains
several symbols.
Symbols
The following symbols indicate certain settings and
modes of your Profiset 30isdn:
C
Programming mode
Call forwarding ON
X
Callback ON or initiating callback is possible
Y
Conference
K
Locking function ON
J
DTMF ON
N
Microphone OFF
M
Loudspeaker (open listening) ON
L
Profiset 30isdn engl.: A30853-X300-B107-1-7619
12-digit display line
Display
Idle mode
00.00.00 00:00
06.07.98 13:58
- - . - - . - - - - : - -
Date, time, call numbers, call charge and call time are displayed in accordance with the relevant settings and
modes of the telephone. Calls involving two or more parties (e.g. consultation, call waiting, three-party conference) are indicated by a digit at the first position of the display line.
Two brackets at the beginning and the end of the display
line indicate a supressed or not transmitted call number.
Display after the Profiset 30isdn has been plugged into
the ISDN socket.
Display after the first successful outgoing call has been
conducted and the date/time have been transmitted from
the switching centre.
Display of the telephone in restricted powering condition
without mains voltage (230V) from the NTBA (only with
the restricted powering switch in ON position ➔ page 4).
7
27.11.98
kap01.fm5
Display-driven telephone operation
Connected mode
In the course of a call, the call number of the called party
030234577
001.20 00:30
(- - - - - - - - - )
2 045672343
3 045672343
(if it is transmitted or display is not suppressed) is shown.
The display can alternate between charge (if tariff unit fac-
tor is entered)/call time of the current call (if it is activated
➔ page 35) and the call number. The call time is displayed
in minutes and seconds. If the call time exceeds 1 hour,
it switches to hours and minutes.
The call number of the called party is supressed or not
transmitted.
Display of the telephone with one connection put on hold
and one active connection (the call number of the active
call is displayed) or during call waiting (the call number of
the call in waiting is displayed).
Display of the telephone during a three-party conference
(the call number of the caller who was active before the
three-party conference has been set up is displayed).
Profiset 30isdn engl.: A30853-X300-B107-1-7619
8
27.11.98
kap01.fm5
Outgoing and incoming calls
Calling users
c
Lift the handset.
Enter the call number.
T
The call number is dialled and appears on the display.
On-hook dialling
You can enter (or change) the call number and then set up
the connection when the handset is on-hook.
Enter the call number (automatic dialling is possible).
T
Backspace to delete with -.
c and d Lift the handset and talk.
Profiset 30isdn engl.: A30853-X300-B107-1-7619
Outgoing and incoming calls
If “Display of charge/call time of the active call”
is activated (➔ page 35) the display alternates
between call number and call charge/call time.
or
Set up the connection via the Loudspeaker key;
l
Lift the handset in order to be able to talk.
d
There is also another way of on-hook dialling.
(Caution: Editing the entered number is not possible!)
Press the Loudspeaker key.
l
Enter the call number (automatic dialling is possible).
T
The call number is dialled.
c and d Lift the handset and talk
With the Loudspeaker key you can activate/deactivate
l
open listening.
9
27.11.98
kap01.fm5
Outgoing and incoming calls
Number redial (automatic dialling)
The last five numbers dialled are stored automatically. If a user
you wish to contact is busy or unreachable, you can initiate
number redial the next time you attempt to call, without having
to dial the call number again.
Number redial is also possible with the handset on-hook. The
number can be edited if necessary (➔ page 9).
The numbers are sorted in ascending order according to the
date and time. The last number dialled is thus at the top of the
list.
c
Lift the handset.
Press the Number redial key and the call number dialled
W
last is dialled.
or
Press the Number redial key until the desired call number
W
appears on the display,
c
Lift the handset. The call number is dialled.
Profiset 30isdn engl.: A30853-X300-B107-1-7619
The memory for the number redial can be
cleared with the setting “Clear memory”
(➔ page 39). The memory is also cleared when
the ISDN connecting cord has been unplugged.
Dialling call numbers using the Destination dialling keys (automatic dialling)
Frequently used call numbers can be dialled quickly and easily
using destination dialling keys. This means that you do not have
re-enter the number each time.
Destination dialling is also possible with the handset on-hook.
The number can be edited if necessary (➔ page 9). You can also
store parts of numbers and the remaining digits can then be suffix-dialled as required.
Prerequisite: You must have programmed a Destination dialling
key (➔ page 25).
c
Lift the handset.
z
10
Press the Destination dialling key. The stored call number
appears on the display and is dialled.
27.11.98
kap01.fm5
Profiset 30isdn engl.: A30853-X300-B107-1-7619
Outgoing and incoming calls
or
a
Handset is on-hook.
z
or
-
Press the Destination dialling key. The stored call number
is displayed.
Edit or complete the call number if necessary.
T
c
Lift the handset. The call number is dialled.
Dialling call numbers using the Speed dialling keys (automatic dialling)
10 frequently used call numbers can be dialled quickly and
easily using Speed dialling keys. Speed dialling is also possible with the handset on-hook. The call number can be
edited if necessary (➔ page 9). You can also store parts of
numbers and the remaining digits can then be suffix-dialled as required.
Prerequisite: You must have programmed a Speed
dialling key (➔ page 25).
or
k
k
-
and
and
or
c
Lift the handset.
Press first the Speed dialling key and then the relevant
digit key. The stored call number appears on the display
T
and is dialled.
a
Handset is on-hook.
Press first the Speed dialling key and then the relevant
T
digit key. The stored call number is displayed.
Edit or complete the call number if necessary.
T
c
Lift the handset. The call number is dialled.
In order to select a specific network operator,
program the relevant circuit identification code
on a destination or speed dialling key. The remaining number can be suffix dialled from another destination or speed dialling key, the call
list key, the number redial key or via the digit
keys.
11
Loading...