MANUAL
ENGLISH
Airstrike |
V2 |
|
Ordercode: 43158 |
Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
Airstrike |
|
Table of contents |
|
Warning ........................................................................................................................................................................... |
2 |
Safety Instructions ..................................................................................................................................................... |
2 |
Operating Determinations....................................................................................................................................... |
4 |
Rigging........................................................................................................................................................................ |
4 |
Connection with the mains ..................................................................................................................................... |
5 |
Return Procedure...................................................................................................................................................... |
5 |
Claims ......................................................................................................................................................................... |
5 |
Description of the device............................................................................................................................................. |
6 |
Features ...................................................................................................................................................................... |
6 |
Frontside ..................................................................................................................................................................... |
6 |
Backside ..................................................................................................................................................................... |
7 |
Installation ...................................................................................................................................................................... |
7 |
Installing the Lamp.................................................................................................................................................... |
8 |
Set Up and Operation ................................................................................................................................................... |
8 |
Control Modes........................................................................................................................................................... |
9 |
One Airstrike (Auto run mode and Sound-controlled mode)......................................................................... |
9 |
One Airstrike (Manual Mode)............................................................................................................................... |
9 |
Multiple Airstrikes (Master / Slave Control) ......................................................................................................... |
9 |
Multiple Airstrikes (DMX Control)........................................................................................................................ |
10 |
Fixture Linking........................................................................................................................................................... |
11 |
Data Cabling........................................................................................................................................................... |
11 |
Control Panel........................................................................................................................................................... |
12 |
Control Mode .......................................................................................................................................................... |
12 |
DMX Addressing ...................................................................................................................................................... |
12 |
Menu Overview....................................................................................................................................................... |
13 |
Main Menu Options ................................................................................................................................................ |
14 |
1. Startup/Auto run mode................................................................................................................................... |
14 |
2. DMX-512 mode................................................................................................................................................. |
14 |
3. Sound options................................................................................................................................................... |
14 |
4. Master/Slave mode ......................................................................................................................................... |
15 |
5. Display options ................................................................................................................................................. |
15 |
6. Sound-controlled mode.................................................................................................................................. |
15 |
7. Reset .................................................................................................................................................................. |
15 |
8. Manual mode................................................................................................................................................... |
16 |
DMX Channels......................................................................................................................................................... |
16 |
10 channels........................................................................................................................................................... |
16 |
Maintenance................................................................................................................................................................ |
19 |
Replacing the Fuse ................................................................................................................................................. |
19 |
Static Gobo wheel and Color wheel........................................................................................................................ |
20 |
Troubleshooting ........................................................................................................................................................... |
21 |
Changing the Lamp ............................................................................................................................................... |
21 |
No Light..................................................................................................................................................................... |
21 |
No Response to DMX.............................................................................................................................................. |
21 |
Product Specification.................................................................................................................................................. |
23 |
Dimensions ................................................................................................................................................................... |
24 |
Notes.............................................................................................................................................................................. |
25 |
Ordercode: 43158 |
1 |
|
|
Airstrike
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure that all parts are present, and have been received in good condition. Notify the dealer immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
Showtec Airstrike
IEC power cable (1,5 m)
Safety cable
User manual
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular optimum conditions. For this reason when all color LEDs are used at their fullest intensity, life of the LEDs is significantly reduced. If improving your lifespan expectancy is of a higher priority, place care in providing for lower operational temperatures. This may include climatic-environmental and the reduction of overall projection intensity.
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
be qualified
follow the instructions of this manual
Before your initial start-up, please make sure that there is no damage caused by transportation. Should there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the device are not subject to warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
Ordercode: 43158 |
2 |
|
|
Airstrike
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to the device.
Never let the power cord come into contact with other cables! Handle the power cord and all connections with the mains with particular caution!
Never remove warning or informative labels from the unit.
Never use anything to cover the ground contact.
Never place any material over the lens.
Never look directly into the light source.
Never leave any cables lying around.
Do not insert objects into air vents.
Do not connect this device to a dimmerpack.
Do not switch the device on and off in short intervals, as this would reduce the device’s life.
Do not touch the device’s housing bare-handed during its operation. Allow the fixture to cool for at least 5 minutes before handling.
Do not shake the device. Avoid brute force when installing or operating the device.
Only use device indoors, avoid contact with water or other liquids.
Only operate the fixture after having checked if the housing is firmly closed and all screws are tightly fastened.
Only operate the device after having familiarized with its functions.
Avoid flames and do not put close to flammable liquids or gases.
Always keep case closed while operating.
Always allow free air space of at least 50 cm around the unit for ventilation.
Always disconnect power from the mains, when device is not used or before cleaning! Only handle the power cord by the plug. Never pull out the plug by tugging the power cord.
Make sure that the device is not exposed to extreme heat, moisture or dust.
Make sure that the available voltage is not higher than stated on the rear panel.
Make sure that the power cord is never crimped or damaged. Check the device and the power cord from time to time.
If the lens is obviously damaged, it has to be replaced. So that its functions are not impaired, due to cracks or deep scratches.
If device is dropped or struck, disconnect mains power supply immediately. Have a qualified engineer inspect for safety before operating.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature.
If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely (preferably in the original packing material), and return it to your Showtec dealer for service.
For adult use only. Device must be installed out of the reach of children. Never leave the unit running unattended.
Never attempt to bypass the thermostatic switch or fuses.
For replacement use fuses of same type and rating only.
The user is responsible for correct positioning and operating of the Airstrike. The manufacturer will not accept liability for damages caused by the misuse or incorrect installation of this device.
This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to earth.
Repairs, servicing and electric connection must be carried out by a qualified technician.
WARRANTY: Till one year after date of purchase.
Ordercode: 43158 |
3 |
|
|
Airstrike
Operating Determinations
This device is not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects.
The minimum distance between light-output and the illuminated surface must be bigger than 1 meter.
The maximum ambient temperature ta = 40°C must never be exceeded.
The relative humidity must not exceed 50 % with an ambient temperature of 40° C.
If this device is operated in any other way, than the one described in this manual, the product may suffer damages and the warranty becomes void.
Any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all other safety issues.
Do not attempt the installation yourself!
Always let the installation be carried out by an authorized dealer!
Procedure:
If the Airstrike is lowered from the ceiling or high joists, professional trussing systems have to be used.
Use a clamp to mount the Airstrike, with the mounting-bracket, to the trussing system.
The Airstrike must never be fixed swinging freely in the room.
The installation must always be secured with a safety attachment, e.g. an appropriate safety net or safety-cable.
When rigging, derigging or servicing the projector, always make sure, that the area below the installation place is blocked and staying in the area is forbidden.
The Airstrike can be placed on a flat stage floor or be mounted to any kind of truss, with a clamp.
Improper installation can cause serious damage to people and property!
Ordercode: 43158 |
4 |
|
|
Airstrike
Connection with the mains
Connect the device to the mains with the power-plug.
Always pay attention, that the right color cable is connected to the right place.
International |
EU Cable |
UK Cable |
US Cable |
Pin |
L |
BROWN |
RED |
YELLOW/COPPER |
PHASE |
N |
BLUE |
BLACK |
SILVER |
NEUTRAL |
|
YELLOW/GREEN |
GREEN |
GREEN |
PROTECTIVE GROUND |
Make sure that the device is always connected properly to the earth!
Improper installation can cause serious damage to people and property!
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued. Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility. Call Highlite 0031-455667723 or mail aftersales@highlite.nl and request an RMA prior to shipping the fixture. Be prepared to provide the model number, serial number and a brief description of the cause for the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper inside the box:
01) Your name.
02) Your address.
03) Your phone number.
04) A brief description of the symptoms.
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any shortcomings and/or visible defects, or perform this check after our announcement that the goods are at their disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that a fixture is damaged due to shipping. Transportation damage has to be reported to us within one day after receipt of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless otherwise agreed in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement, regardless of the agreement of which the obligation is resulting.
Ordercode: 43158 |
5 |
|
|
Airstrike
Description of the device
Features
The Showtec Airstrike is a light fixture with high output and great effects.
Input voltage: 100-240V AC, 60/50Hz
Power consumption: 265W
Light source: Philips MSD 5R lamp
DMX modes: 10 channels
MIrrors: 4 mirrors
Mirror angle: 60°
Color wheel: 7 colors + white
Gobo wheel: 14 metal gobos + open
DMX-control via standard DMX-controller
Onboard: LED display for easy setup
Control modes: Auto run, Manual mode, Sound-controlled, Master/Slave, DMX-512
Dimmer: 0-100%
Strobe: 1-5 Hz
Housing: Die-cast aluminum
Power connector: IEC power connector
Data connectors: 3-pin XLR IN, 3-pin XLR OUT
IP rating: IP20
Cooling: Cooling fan
Spare Lamp 5R ordercode 80988 / 81013
Fuse: F5AL/250V
Dimensions: 300 x 285 x 340 mm (LxWxH)
Weight: 9,4 kg
Frontside
Fig. 01
01) Mounting bracket with inclination screw
02) Adjustment screw
03) Mirror
Ordercode: 43158 |
6 |
|
|
Airstrike
Backside
Fig. 02
04) LED display + menu buttons
05) Built-in microphone
06) 3-pin DMX signal connector IN
07) 3-pin DMX signal connector OUT
08) IEC power connector 100-240V AC + fuse F5AL/250V
09)Power switch ON/OFF
10)Ground/earth connection
11)Air intake grill
Installation
Remove all packing materials from the Airstrike. Check if all foam and plastic padding is removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly. Always disconnect from electric mains power supply before cleaning or servicing. Damages caused by non-observance are not subject to warranty.
Ordercode: 43158 |
7 |
|
|
Airstrike
Installing the Lamp
The Showtec Airstrike uses the 5R (ordercode 80988 / 81013) reflectorbulb as manufactured by all popular manufacturers. Use only the appropriate lamp for your unit.
Note that, product versions that use other lamps, may be offered in the future. Check your product specification label for information.
Always disconnect from electric mains power supply before changing lamps. The lamp has to be replaced when it is damaged or deformed due to the heat.
Do not install lamps with a higher wattage! Lamps with a higher wattage generate temperatures the device was not designed for.
Damages caused by non-observance are not subject to warranty.
Procedure:
01) Loosen the 4 screws on the back of the housing. 02) Gently remove the small metal housing.
03) Read lamp instructions. Do not touch the lamp bulb glass. (See Figure 3.). Oil on hands shortens the lamp life. (If you touch the bulb glass, wipe off the glass with a clean, lint-free towel and rubbing alcohol.).
04) Insert the lamp into the lamp socket.
05) Put the lamp cover back and fasten the screws snugly.
Fig. 03
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Ordercode: 43158 |
8 |
|
|
Loading...