Sharp XG-NV5XB Service Manual

XG-NV5XB

SERVICE MANUAL

S99O4XG-NV5XB

LCD PROJECTOR

MODEL

In the interests of user-safety (Required by safety regulations in some countries) the set should be restored
to its original condition and only parts identical to those specified should be used.

XG-NV5XB

CONTENTS

Page Page

• SPECIFICATIONS.............................................. 2

• IMPORTANT SERVICE SAFETY NOTES..........3

• NOTE TO SERVICE PERSONNEL....................4

• OPERATION MANUAL ...................................... 7

• REMOVING OF MAJOR PARTS...................... 13

• RESETTING THE TOT AL LAMP TIMER.......... 18

• THE OPTICAL UNIT OUTLINE........................ 19

• CONVERGENCE AND

FOCUS ADJUSTMENT................................... 20

• ELECTRICAL ADJUSTMENT .......................... 25

• ADJUSTING THE PC BOARD .........................30

• TROUBLE SHOOTING TABLE ........................ 31

• CHASSIS LAYOUT .......................................... 46

• BLOCK DIAGRAM ...........................................48

• OVERALL WIRING DIAGRAM......................... 50

• DESCRIPTION OF SCHEMATIC DIAGRAM ...52

• WAVEFORMS .................................................. 53

• SCHEMATIC DIAGRAM................................... 54

• PRINTED WIRING BOARD ASSEMBLIES.... 110

• PARTS LIST

Ë

ELECTRICAL PARTS................................. 123

Ë

CABINET AND MECHANICAL PARTS ......146

Ë

ACCESSORIES PARTS............................. 152

Ë

PACKING PARTS....................................... 152

• PACKING OF THE SET .................................153

SHARP CORPORATION

This document has been published to be used for
after sales service only.
The contents are subject to change without notice.

1

XG-NV5XB

Specifications

Product type

Model

Video system

Display method

LCD panel

LCD Projector
XG-NV5XB
PAL/SECAM/NTSC 3.58/NTSC 4.43
LCD panel 2 3, RGB optical shutter method
Panel size: 0.99 (13.9 [H] 2 18.5 [W] mm)
Display method: Translucent TN liquid crystal panel
Drive method: TFT (Thin Film Transistor) Active Matrix panel
No. of dots: 786,432 dots (1,024 [H] 2 768 [V])

Lens

Brightness (ANSI lumen)

Projection lamp

Contrast ratio

Video input signal

1–1.32 zoom lens, F1.7–2.0, f 4 33–43 mm
DC 180 W lamp
1000 ANSI lumens
200:1
RCA Connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 Ω terminated
RCA Connector: AUDIO, 0.5 Vrms more than 22 kΩ (stereo)

S-video input signal

4-pin mini DIN connector
Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated

Horizontal resolution

Audio output

Computer RGB input signal

700 TV lines (video input)
2 W (monaural)

Video signal

15-

PIN MINI

D-

SUB CONNECTOR

sync/sync on green type analog input: 0–0.7 Vp-p, positive, 75 Ω terminated

TEREO MINIJACK

S

ORIZONTAL SYNC. SIGNAL

H

: AUDIO, 0.5 Vrms, more than 22 kΩ (stereo)

only)

ERTICAL SYNC. SIGNAL

Computer control signal

Speaker system

Rated voltage

Input current

Rated frequency

Power consumption

Operating temperature

Storage temperature

Cabinet

I/R Carrier frequency

Laser Pointer of Remote Control

Dimensions (approx.)

V

9-pin D-sub male connector (RS-232C Input Port)

3

⁄329 (8 cm) round

3
AC 110–120/220–240 V

2.6 A/1.3 A
50/60 Hz
290 W
41°F to 104°F (‘ 5°C to ‘ 40°C)
1 4°F to 140°F (1 20°C to ‘ 60°C)
Plastic
40 kHz

Wave length:
Max. output:

Class II Laser Product

1

⁄649 (W) 2 4 49⁄649 (H) 2 12 13⁄649 (D) (229 2 121 2 310 mm) (main body only)

9

19

⁄329 (W) 2 5 3⁄649 (H) 2 13 41⁄649 (D) (243.5 2 128 2 346.4 mm) (including an ad-

9

670 nm

1 mW

justment foot and projecting parts)

Weight (approx.)

Supplied accessories

4.9 kg
“Power” remote control, Simple presentation remote control, Four AA size batteries,
Two AAA size batteries, Power cord (98 109, 3 m), Computer cable (98 109, 3 m),
Computer audio cable (98 109, 3 m), Macintosh adaptor, Mouse control serial cable
(38 39, 1 m), Mouse control cable for IBM PS/2 (38 39, 1 m), Mouse control cable for
Mac (6

45

⁄649, 17 cm), Remote mouse receiver, Extra air filter, Lens cap (attached),
Carrying bag, CD-ROM, LCD projector operation manual, LCD projector quick
reference, Sharp Advanced Presentation Software operation manual, Sharp
Advanced Presentation Software quick reference

Replacement parts

Lamp unit (Lamp/cage module) (BQC-XGNV5XB/1), “Power” remote control
(RRMCG1470CESA), Simple presentation remote control (RRMCG1480CESA), AA
size batteries, AAA size batteries, Power cord (QACCU5013CEZZ), Computer cable
(QCNW-5108CEZZ), Computer audio cable (QCNW-4870CEZZ), Macintosh adaptor
(QPLGJ1512CEZZ), Mouse control serial cable (QCNW-5112CEZZ), Mouse control
cable for IBM PS/2 (QCNW-5113CEZZ), Mouse control cable for Mac (QCNW­5114CEZZ), Remote mouse receiver (RUNTK0648CEZZ), Air filter (PFILD0076CEZZ),
Lens cap (GCOVH1307CESB), Carrying bag (GCASN0001CESA), CD-ROM (UDSKA­0007CE01), LCD projector operation manual (TINS-6791CEZZ), LCD projector quick
reference (TINS-6598CEN1), Sharp Advanced Presentation Software operation
manual (TINS-6601CEN1), Sharp Advanced Presentation quick reference (TINS­6676CEZZ), IrDA driver installation instruction sheet (TCAUZ3046CEZZ)

This SHARP projector uses LCD (Liquid Crystal Display) panels. These
very sophisticated panels contain 786,432 pixels (2 RGB) TFTs (Thin
Film Transistors). As with any high technology electronic equipment
such as large screen TVs, video systems and video cameras, there
are certain acceptable tolerances that the equipment must conform
to.

Specifications are subject to change without notice.

(Computer Input Port 1, 2): RGB separate/composite

: TTL level (positive/negative) or composite sync (Apple

: Same as above

This unit has some inactive TFTs within acceptable tolerances which
may result in illuminated or inactive dots on the picture screen. This
will not affect the picture quality or the life expectancy of the unit.
If you have any questions about this matter, please call toll free 1-800­BE-SHARP (1-800-237-4277).

U.S.A. ONLY

2

XG-NV5XB

2
2

IMPORTANT SERVICE SAFETY NOTES

Ë

Service work should be performed only by qualified service technicians who are thoroughly
familiar with all safety checks and servicing guidelines as follows:

WARNING

1. For continued safety, no modification of any circuit
should be attempted.

2. Disconnect AC power before servicing.

BEFORE RETURNING THE PROJECTOR:
(Fire & Shock Hazard)

Before returning the projector to the user, perform
the following safety checks:

1. Inspect lead wires are not pinched between the
chassis and other metal parts of the projector.

2. Inspect all protective devices such as non-metallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacity networks, mechanical
insulators, etc.

3. To be sure that no shock hazard exists, check for
current leakage in the following manner:

» Plug the AC cord directly into a 120-volt AC outlet,

(Do not use an isolation transformer for this test).

» Using two clip leads, connect a 1.5k ohm, 10 watt

resistor paralleled by a 0.15µF capacitor in parallel
between all exposed metal cabinet parts and earth
ground.

» Use an AC voltmeter with sensitivity of 5000 ohm per

volt., or higher, sensitivity to measure the AC voltage
drop across the resistor (See Diagram).

» All checks must be repeated with the AC plug

connection reversed. (If necessary, a non-polarized
adapter plug must be used only for the purpose of
completing these checks.)
Any reading of 0.3 volts RMS (this corresponds to

0.2 milliamp. AC.) or more is excessive and indicates
a potential shock hazard which must be corrected
before returning the unit to the owner.

AC

VOLTMETER

1.5k ohm (10W)

0.15µF

TEST PROBE

TO EXPOSED
METAL PARTS

CONNECT TO KNOWN
EARTH GROUND

234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121

SAFETY NOTICE

Many electrical and mechanical parts in LCD Projector
have special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
necessarily increased by using replacement components
rated for higher voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified by “å”
and shaded areas in the Replacement Parts Lists and
Schematic Diagrams. For continued protection,
replacement parts must be identical to those used in the
original circuit. The use of a substitute replacement parts
which do not have the same safety characteristics as
the factory recommended replacement parts shown in
this service manual, may create shock, fire or other
hazards.

AVIS POUR LA SECURITE

De nombreuses pièces, électriques et mécaniques, dans
les projecteur à LCD présentent des caractéristiques
spéciales relatives à la sécurité, qui ne sont souvent
pas évidentes à vue.
Le degré de protection ne peut pas être nécessairement
augmentée en utilisant des pièces de remplacement
étalonnées pour haute tension, puissance, etc.
Les pièces de remplacement qui présentent ces
caractéristiques sont identifiées dans ce manuel;
les pièces électriques qui présentent ces particularités
sont identifiées par la marque “å” et hachurées dans la
liste des pièces de remplacement et les diagrammes
schématiques. Pour assurer la protection, ces pièces
doivent être identiques à celles utilisées dans le circuit
d’origine. L’utilisation de pièces qui n’ont pas les mêmes
caractéristiques que les pièces recommandées par
l’usine, indiquées dans ce manuel, peut provoquer des
électrocutions, incendies ou autres accidents.

WARNING: The bimetallic component has the primary

conductive side exposed. Be very careful in
handling this component when the power is on.

234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121

AVERTISSEMENT: La composante bimétallique dispose du

conducteur primaire dénudé. Faire
attention lors de la manipulation de cette
composante sous tension.

3

XG-NV5XB

NOTE TO SERVICE
PERSONNEL

UV-RADIATION PRECAUTION

The light source, metal halide lamp, in the LCD
projector emits small amounts of UV-Radiation.

A VOID DIRECT EYE AND SKIN EXPOSURE.

To ensure safety please adhere to the following:

1. Be sure to wear sun-glasses when servicing the
projector with the lamp
turned “on” and the top
enclosure removed.

2. Do not operate the lamp outside of the lamp housing.

NOTE POUR LE PERSONNEL
D’ENTRETIEN

PRECAUTION POUR LES RADIATIONS UV

La source de lumière, la lampe métal halide, dans le
projecteur LCD émet de petites quantités de
radiation UV.

EVITEZ TOUTE EXPOSITION DIRECTE
DES YEUX ET DE LA PEAU.

Pour votre sécurité, nous vous prions de respecter
les points suivants:

1. Toujours porter des lunettes de soleil lors d’un
entretien du projecteur
avec la lampe allumée
et le haut du coffret retiré.

2. Ne pas faire fonctionner la lampe à l’extérieur du
boîtier de lampe.

3. Do not operate for more than 2 hours with the
enclosure removed.

UV-Radiation and Medium Pressure
Lamp Precautions

1. Be sure to disconnect the AC plug when replacing
the lamp.

2. Allow one hour for the unit to cool down before
servicing.

3. Replace only with same type lamp. Type
CLMPF0057DE01 or BQC-XGNV5XB/1 rated 75V/
180W.

4. The lamp emits small amounts of UV-Radiation, avoid
direct-eye contact.

5. The medium pressure lamp involves a risk of
explosion. Be sure to follow installation instructions
described below and handle the lamp with care.

3. Ne pas faire fonctionner plus de 2 heures avec le
coffret retiré.

Précautions pour les radiations UV
et la lampe moyenne pression

1. Toujours débrancher la fiche AC lors du
remplacement de la lampe.

2. Laisser l’unité refroidir pendant une heure avant de
procéder à l’entretien.

3. Ne remplacer qu’avec une lampe du même type.
Type CLMPF0057DE01 or BQC-XGNV5XB/1,
caractéristique 75V/180W.

4. La lampe émet de petites quantités de radiation UV­éviter tout contact direct avec les yeux.

5. La lampe moyenne pression implique un risque
d’explosion. Toujours suivre les instructions
d’installation décrites ci-dessous et manipuler la
lampe avec soin.

4

XG-NV5XB

5

4

5
5

234567890123456789012345678901212345678901234

UV-RADIATION PRECAUTION (Continued)

23456789012345678901234567890121234567890123

Ë

Lamp Replacement

Note:

Since the lamp reaches a very high temperature
during units operation replacement of the lamp
should be done at least one hour after the power
has been turned off. (to allow the lamp to cool off.)
Installing the new lamp, make sure not to touch the
lamp (bulb) replace the lamp by holding its reflector

2.
[Use original replacement only.]

Lamp

1

Reflector

2

DANGER ! –– Never turn the power on without the
lamp to avoid electric-shock or damage of the
devices since the stabilizer generates high voltages
at its start.

234567890123456789012345678901212345678901234

PRECAUTION POUR LES RADIATIONS UV (Suite)

234567890123456789012345678901212345678901234

Ë

Remplacement de la lampe

Remarque:

Comme la lampe devient très chaude pendant le
fonctionnement de l’unité, son remplacement ne doit
être effectué au moins une heure après avoir coupé
l’alimentation (pour permettre à la lampe de refroidir).
En installant la nouvelle lampe, s’assurer de ne pas
toucher la lampe (ampoule). Remplacer la lampe en
tenant son réflecteur 2.
[N’utiliser qu’un remplacement d’origine.]

Lampe

1

Reflecteur

2

DANGER ! –– Ne jamais mettre sous tension sans
la lampe pour éviter un choc électrique ou des
dommages des appareils car le stabilisateur génère
de hautes tensions à sa mise en route.

Since small amounts of UV-Radiation are emitted
from an opening between the duct cover and the
lamp housing, it is recommended to place the LENS
CAP on the opening during servicing to avoid eye
and skin exposure (Fig. 1).

Note: Please obtain a lens cap before servicing a

model XG-NV5XB that is received without
one.

LENS CAP CAPUCHON D'OPTIQUE

SHARP

Comme de petites quantités de radiation UV sont
émises par une ouverture entre le couvercle du con­duit et le botier de la lampe,il est recommandé de
placer le CAPUCHON D'OPTIQUE sur l'ouverture
pendant l'entretien pour éviter une exposition des
yeux et la peau (Fig. 1).

Remarque: Priére de se procurer un capuchon

d'optique acant d'entretien un modéle
XG-NV5XB qui est livré sans.

SHARP

Figure 1.

Figure 1.

5

XG-NV5XB

2

WARNING: High brightness light source, do not stare into the beam of light, or view directly . Be especially

careful that children do not stare directly in to the beam of light.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO

MOISTURE OR WET LOCATIONS.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT REMOVE SCREWS

EXCEPT SPECIFIED USER

SERVICE SCREW

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE CABINET.

NO USER-SERVICEABLE P ARTS EXCEPT LAMP UNIT.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lighting flash with arrowhead within a
triangle is intended to tell the user that
parts inside the product are risk of electric
shock to persons.

The exclamation point within a triangle is
intended to tell the user that important
operating and servicing instructions are in
the manual with the projector.

CAUTION

(INLET Unit)

For continued protection
against a risk of fire,
replace only with same

5A 250V

234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121

A VERTISSEMENT : Source lumineuse de grande intensité. Ne pas fixer le faisceau lumineux ou le regarder

type 5A 250V fuse.
(F701)

directement. Veiller particulièrement à éviter que les enfants ne fixent directement le
faisceau lumineux.

A VERTISSEMENT : AFIN D’EVITER TOUT RISQUE D’INCENDIE OU D’ELECTROCUTION, NE P AS PLACER

CET APPAREIL DANS UN ENDROIT HUMIDE OU MOUILLE.

ATTENTION

RISQUE

D’ELECTROCUTION NE

PASRETIRER LES VIS, A

L’EXCEPTION DES VIS DE

REPARATION UTILISATEUR

SPECIFIEES

L’éclair terminé d’une flèche à l’intérieur
d’un triangle indique à l’utilisateur que les
pi‘eces se trouvant dans l’appareil sont
susceptibles de provoquer une décharge
électrique.

Le point d’exclamation à l’intérieur d’un

ATTENTION: POUR EVITER T OUT RISQUE

D’ELECTROCUTION, NE PAS RETIRER LE CAPOT.

AUCUNE DES PIECES INTERIEURES N’EST REPARABLE

PAR L’UTILISATEUR, A L’EXCEPTION DE L’UNITE DE

LAMPE. POUR TOUTE REPARA TION, S’ADRESSER A UN

TECHNICIEN D’ENTRETIEN QUALIFIE.

triangle indique à l’utilisateur que les
instructions de fonctionnement et
d’entretien sont détaillées dans les
documents fournis avec le projecteur.

PRECAUTION

(Unite d’admission)

Pou r une protection
continue contre les risques
d’incendie, ne remplacer
qu’avec un fusible 5A

5A 250V

250V du même type.
(F701)

6

Location of Controls

Projector

Front View

1 POWER indicator
2 POWER buttons (ON/OFF)
3 BLACK SCREEN button
4 INPUT SELECT button

5 FREEZE button
6 KEYSTONE button
7 ADJUSTMENT buttons (∂ /ƒ/

ß / ©)

8 LAMP REPLACEMENT indicator
9 TEMPERATURE WARNING indi-

cator

0 VOLUME buttons (‘ /1 )
q MUTE button
w MENU button
e IrCOM button
r AUTO SYNC button
t ENLARGE button
y ENTER button

u Zoom knob
i Focus knob
o Remote control sensor
p Air filter /Cooling fan

(Intake vent)

a Carrying handle
s Kensington Security Standard

connector

d Foot release
f Cooling fan (Exhaust vent)
g Remote control sensor
h Speaker
j Cooling fan (Intake vent)
k Air filter
l COMPUTER INPUT 1 port

(HD-15)

; RS-232C port (9-pin D-sub)

J

AUDIO INPUT terminals: RCA

K

AC socket

L

MAIN POWER switch

:

COMPUTER INPUT 2 port
(HD-15)

a

AUDIO OUTPUT terminal
(3.5 mm stereo minijack)

s

COMPUTER AUDIO INPUT
terminal (3.5 mm stereo minijack)

d

S-VIDEO INPUT terminal: 4-pin
mini DIN

f

IrCOM sensor

g

VIDEO INPUT terminal: RCA

1

2

3
4

5
6

7

u
i
o

p

a

s

d

9

8

0
q

w
e

r
t

y

f

l

;

J

K
L

g

h

j

k

:

a

s

d

f

g

Side and Rear View

XG-NV5XB

7

XG-NV5XB

Operating the Wireless Mouse Remote Control

“Power” Remote Control

Front View

1

2

3

TOOLS

4

5
6
7

8

ON

OFF

BLACK

SCREEN

R-CLICK ENTER

INPUT

FREEZE

KEYSTONE

MOUSE

LCD PROJECTOR

MUTE

LASER

AUTO SYNC

ENLARGE

LIGHT

IrCOM

ADJ.

VOL

MENU

9

0

q

w

e
r
t

y

Side View

ON

R/C

OFF

T op View

u

i

o

p

1 MUTE button
2 POWER buttons (ON/OFF)
3 BLACK SCREEN/TOOLS button
4 RIGHT-CLICK/ENTER button

5 INPUT button
6 FREEZE button
7 KEYSTONE button
8 MOUSE/ADJUSTMENT switch

9 TRANSMISSION indicator
0 VOLUME buttons (‘ /1 )
q LASER POINTER/MENU button

w MOUSE/ADJUSTMENT buttons (∂/ƒ/ß/©)
e IrCOM button

r AUTO SYNC button
t ENLARGE button
y BACKLIGHT button
u MAIN POWER switch
i LEFT-CLICK (BACK) button
o Remote control signal transmitter
p Laser pointer window
a MOUSE signal transmitter
s MOUSE button
d RIGHT-CLICK button
f LEFT-CLICK button

Simple Presentation Remote Control

Side ViewFront View

a

s

d

f

8

Inserting the batteries

XG-NV5XB

Press in and downward

13

on the arrow to remove
the battery cover.

I

nsert four AA size batteries

2

for the “Power” remote
control and two AAA size
batteries for the simple
presentation remote control

Insert the side tabs of
the battery cover into
their slots and press the
cover in until it is

properly seated.
making sure their polarities
match the ‘ and 1 marks
inside the battery
compartment.

Battery

cover

Battery

cover

Battery

compartment

Battery

compartment

Battery

cover

Battery

cover

• The “Power” remote control can be used to control the projector within the ranges shown below.

• The remote mouse receiver can be used with the “Power” remote control or the simple presentation remote
control to control the mouse functions of a connected computer within the ranges shown below.

• The signal from the remote controls can be reflected off a screen for easy operation. However, the effective distance of the
signal may differ due to the screen material.

Controlling the Projector

238 (7 m)

30˚

“Power”
remote
control

45˚

30˚

45˚

30˚

“Power”
remote
control

Using the Wireless Mouse

Simple
presentation
remote control

138 (4 m)

“Power” remote control

30˚

30˚

30˚

Remote
mouse
receiver

120˚

9

XG-NV5XB

When operating the

projector controls

MOUSE

ON

MUTE

OFF

BLACK

SCREEN

TOOLS

R-CLICK ENTER

INPUT

FREEZE

KEYSTONE

MOUSE

LIGHT

LCD PROJECTOR

LASER

IrCOM

AUTO SYNC

ENLARGE

ADJ.

VOL

MENU

4
5 2

MOUSE

ADJ.

ADJ.

When operating the
wireless mouse or

using the laser pointer

MOUSE

ON

R/C

OFF

ADJ.

2 2

5 1

The “Power” remote control has the following three func­tions:

• Operation of projector controls

• Operation of wireless mouse

• Use of laser pointer
Slide the MOUSE/ADJUSTMENT switch to the MOUSE
or ADJ. position for use of the function.

1 Connect the projector to a computer
2 Wireless mouse operation

1. After connecting the projector and the computer, turn
the projector on first. The computer should always be
turned on last.

2. Slide the MAIN POWER switch on the “Power” remote
control to ON.

3 Selecting the operation mode

To use the “Power” remote control as a wireless mouse, slide
the MOUSE/ADJUSTMENT switch to the MOUSE position.

• To use the “Power” remote control to operate the projector, slide

the MOUSE/ADJUSTMENT switch to the ADJ. position.

• The wireless mouse or RS-232C function may not operate if your
computer serial port is not correctly set up. Please refer to the
computer’s operation manual for details on setting up/installing the
correct mouse driver.

4 Moving the mouse cursor

Press ∂/ƒ/ß/© on the “Power” remote control to move the
mouse cursor around the screen.

Button name

LASER POINTER/MENU
BLACK SCREEN/TOOLS
RIGHT-CLICK/ENTER
MOUSE/ADJUSTMENT
LEFT-CLICK/BACK
POWER ON/OFF
VOLUME ‘ /1
MUTE
INPUT
IrCOM
FREEZE
AUTO SYNCHRONIZATION
KEYSTONE
ENLARGE

TOOLS

Mouse cursor

Position of MOUSE/ADJUSTMENT switch

MOUSE

LASER POINTER (GREEN)
BLACK SCREEN (GREEN)
RIGHT-CLICK (GREEN)
MOUSE (GREEN)
LEFT-CLICK (NOT LIT)

VOL

ON

MUTE

OFF

BLACK

LASER

SCREEN

MENU

LASER POINTER button

R-CLICK ENTER

INPUT

IrCOM

AUTO SYNC

FREEZE

KEYSTONE

MOUSE

LIGHT

LCD PROJECTOR

ENLARGE

ADJ.

MOUSE

BACKLIGHT button

MENU (RED)
TOOLS (RED)
ENTER (RED)
ADJUSTMENT (RED)
BACK (NOT LIT)

ON (RED)

ADJ.

ADJ.

• The supplied simple presentation remote control can also be used
for wireless mouse operation.

5Using the mouse buttons for two-button mouse

systems

The wireless mouse is configured to be used as a standard
two-button mouse (desktop mouse).

1. Use LEFT-CLICK on the back of the “Power” remote

control as the “Left Click” of a standard desktop mouse.

2. Use RIGHT-CLICK on the front of the “Power” remote

control as the “Right Click” of a standard desktop
mouse.

• For one-button mouse systems, use either the LEFT-CLICK or

RIGHT-CLICK button.

Using the laser pointer

Slide the MOUSE/ADJUSTMENT switch to the MOUSE
position, and then press LASER POINTER (
the laser pointer. When the button is released, the light
automatically goes off.

• For safety reasons, the laser pointer automatically goes off after
1 minute of continuous use. To turn it on again, press LASER
POINTER (

) one more time.

) to activate

Using the “Power” remote control in a dark
room

The “Power” remote control has a backlight function. When
BACKLIGHT is pressed, the remote buttons light up. Green
light refers to mouse operations, and red light to projector
adjustments.

• If the MAIN POWER switch on the “Power” remote control is left on
for more than 10 minutes without operation, the power will
automatically turn off. To turn the power back on, press any button
on the remote control for more than one second.

10

Connection Pin Assignments

XG-NV5XB

11

XG-NV5XB

4

Dimensions

(259)

64

/

13

10

(33.5)

16

/

5

1

(237.5)

32

/

11

9

Rear View

T op View

55

/64 (22)

(27.5)

64

/

5

1

13

19

7

(61)5

32

/
2

(142)

32

/

(11)

16

/

13

(310)5

64

/
12

(337)

64

/

17

13

(346.4)

64

/

41

13

3

3 5/16 (84)3 5/16 (84)

/4 (19)

9

/32 (7)

9

(261)

32

/
10

Side View

1

(77)

32

/
3

(93)

32

/

21

3

15

(24)

16

/

63

/64 (25)

9 19/32 (243.5)

1

/64 (229)

9

7

/16 (11)

(61)4

32

/

13

2

(16)

8

/

5

13

/32 (10.5)

Front View

(128)

(121)

64

64

/

/

3

49

Bottom View

1

11

/16 (43)

7

2

2

1

3

/16 (62)

3

/4 (70)

/32 (77)

12

Units: inches (mm)

REMOVING OF MAJOR PARTS

1.Removing the Intake cover and lamp unit

1-1. Detach the Intake cover.
1-2. Loosen the lamp cover screw and draw out the lamp cover in the direction of arrow (toward yourself).
1-3. Remove the two lamp unit lock screws. Detach the lamp unit.

SHARP

XG-NV5XB

Intake cover

Note:

When replacing the lamp, make sure
that there is a clearance of over
8mm between the terminal and the
lamp snap-on spring (and other
metallic parts).

Lamp snap-on spring

Lamp unit

1-3

1-3

1-2

1-1

Lamp cover

13

XG-NV5XB

2.Removing the top and rear cabinets

2-1. Remove the five rear cabinet lock screws.
2-2. Remove the four terminal board lock screws off the rear cabinet. Unhook and detach the rear cabinet from

below.

2-3. Remove the four top cabinet lock screws from below.

SHARP

2-1

Press both sides of the bottom
cabinet in the directions of
arrow to undo the hooks. Lift
and detach the top cabinet.

2-3

Hook

2-2

2-4. Slowly lift the top cabinet and disconnect the operation key unit connector (KY). Then take away the top

cabinet.

Top cabinet

SHARP

(KY)

2-4

Rear cabinet

14

3. Removing the PWB units

3-1. Disconnect the connectors.
3-2. Remove the twelve screws and detach the output Unit top shield.
3-3. Remove the two screws and detach the PC I/F Unit.
3-4. Remove the two screws and the spacer (stud bolt).Lift and detach the Unit assembly .
3-5. Remove the S-out/REG unit angle lock screw and take out the S-out/REG unit.

3-2

Output Unit top shield

3-3

XG-NV5XB

PC I/F Unit

3-4

Signal Unit

PC Terminal Unit

3-1

Video Unit

3-4

(FS)

(FP)

(L)
(Q)

(FN)

Spacer (stud bolt)

Output Unit

(EB)

(EB)

3-1

3-4

(F)

(SO)

(SO)

3-5

S-out/REG Unit Angle

(EA)

(EB)

(SP)

S-out/REG Unit

15

XG-NV5XB

4.Removing the Power/Ballast unit assembly

4-1. Remove the Power/Ballast unit assembly lock screw.
4-2. Remove the two lamp socket holder lock screws and take out the holder.
4-3. Disconnect the connector (BA) from the ballast unit.
4-4. Remove the (FG) lead lock screw.
4-5. Lift the Power/Ballast unit assembly off the position.

4-4

4-1

4-2

(FG)

Power/Ballast Unit Ass'y

4-5

4-3

(BA)

16

5.Removing the optical mechanism unit

5-1. Remove the six optical mechanism unit lock screws. Lift the unit off the position.

6.Removing the ballast unit and inlet unit

6-1. Disconnect the connector (PA) from the inlet unit. Take out the AC power switch.
6-2. Pull the inlet unit toward yourself off the position.
Note: Before installing the lamp cover, make sure the AC power switch is at the " " (OFF) position.

5-1

XG-NV5XB

Duct Fan Unit

AC power switch
(for Lamp replacement)

6-1

(FG)

Optical Mechanism Unit

(BA)

(PA)

(PA)

6-2

Cover

Inlet Unit

17

XG-NV5XB

RESETTING THE TOTAL LAMP TIMER

When the lamp has been replaced, reset the total lamp timer in the following steps.
Resetting procedure

1. While holding down the “ENTER”, “ADJ."” and “ADJ.|” keys on the set at the same time, turn on the main
power switch (located side the AC inlet).

2. Now the total lamp timer is reset to zero. “000H” appears on the screen.

POWER

ON

OFF

INPUT

SELECT

FREEZE

KEYSTONE

LAMP

I

O

BLACK
SCREEN

B

√

ENTER ADJ." ADJ.|

MUTE

√

MENU

√

ENTER

TEMP.

+

VOLUME

–

IrCOM

√

AUTO SYNC

ENLARGE

The projector will not operate after the lamp timer exceeds 1500hrs. If the lamp re­placement indicator is red, and the projector will not power on, replace the lamp and
reset the lamp timer.

18

THE OPTICAL UNIT OUTLINE

Layout of the optical system

Note: Layout for positioning the optical system.

Incident polarizing plate B

XG-NV5XB

Projection Lens

M4/M6

Dichroic coating
(B reflection)

M4/M6

AR coating

B reflector

Relay lens 2

B reflector

BLUE

RL3

Relay lens 3

Dichroic coating
(G transmission)

RL2

emergent polarizing

B-LCD

CL3

RL1

Relay lens 1

plate B

Cross dichroic prism

G-LCD

Porarizing film

Condenser lens G

GREEN

BLUE

G reflector

* M3

UV-IR coating

Marking

emergent polarizing plate R

Dichroic coating (R transmission)

R-LCD

AL-coated mirror R

CL2

Condenser lens R

emergent
polarizing plate G

Marking
(Bottom)

Porarizing film

RL4

Dichroic coating

PBS(polarization
beam splitter)

M5

AL-deposited face

(R reflection)

RL4

RED

M2

B/G reflector

CL1

* The M3 mirrors have a coating

wedge (for different film thick­ness). Set up these mirrors, with
their markings positioned as
shown above, so that their
coated faces and both sides be
in the correct directions.

DC lamp

(Light source)

Fly-eye lens (outgoing light)

Fly-eye lens (incoming light)

19

AL-deposited
face

M1

AL-coated mirror W

XG-NV5XB

CONVERGENCE AND FOCUS ADJUSTMENT

» Start the convergence and focus adjustments with the top panel removed but the power

on. Use the remote control to adjust the image.
Take the following procedures.

1. Focusing the projection lens

(A) Replacing all the 3 LCD panels

1. Before replacing all the 3 LCD panels, project an image on the screen and bring it into focus.

2. Replace the LCD panels with new ones. But until the focus has been completely readjusted, be careful not
to change the projection distance between the set and the screen, nor to move the projection lens focus
and zoom rings.

Note:

If the focus is readjusted with a different positional relation, the relation between the projection distance
and the screen size is affected. In other words, a short-distance image (40 WIDE for example) may get out
of the focus range, or a long-distance image (300 WIDE for example) may come out of the focus.

(B) Replacing 1 or 2 of the 3 LCD panels

1. In adjusting the focus after replacement of one or two LCD panels, project an image on the screen and turn
the projection lens focus ring to get the non-replaced LCD panel into focus.

2. But until the focus has been completely adjusted for the new LCD panels, be careful not to change the
projection distance between the set and the screen, nor to move the projection lens focus and zoom rings.

3. If the projection distance has been changed or the projection lens readjusted, repeat the above steps 1 and

2.

2. Focus adjustment

(A) Adjusting the G-LCD panel(Make this adjustment on the white-only screen.)

1. Adjustment in θX and Z directions .
Loosen the lock screw "a" and insert an eccentric screwdriver into the notch and hole "a". Turn the screwdriver
until the top, center and bottom on the screen get into focus. In adjusting this top-to-bottom focus, tighten
the lock screws "b" and "c" to fix the θY direction adjustment.
First get the right and left halves in balance. Then improve the accuracy while making the adjustment 2
below.

2. Adjustment in θY direction
T emporarily tighten the lock screw "a" and loosen the lock screws "b" and "c". Insert the eccentric screwdriver
into the notch and hole "c" for adjusting in the θY direction on the top of the screen. Insert the eccentric
screwdriver into the notch and hole "b" for adjusting in the θY direction on the bottom of the screen.

3. Repeat the above steps 1 and 2 to finely adjust the focus. Finally tighten up all the lock screws.

Notes :

1 Carefully proceed with the focus adjustment because the adjusting directions are correlated.
2 In adjusting the convergence and focus, do not move the projection lens zoom and focus rings until the end

of all the adjustments.

(B) Adjusting the B-LCD panel (Do the same for the R-LCD panel.)

1. Take the same procedure as for the G-LCD panel focus adjustment. Note that the adjustment range is
wider in the Z direction. If the convergence is quite different between the B-LCD and G-LCD panels,
roughly adjust the convergence first and then the focus.

3. Convergence adjustment

» Use a crosshatch pattern signal for this adjustment.

Make the adjustment just for the G-LCD and the relevant color.

1. Loosen the convergence lock screw "d".

2. Adjustment in Y and θZ directions
Put a hex wrench in the Y and θZ direction adjustment zone.

3. Adjustment in X direction
Put an eccentric cam adjusting wrench in the X direction adjustment zone.

20

4. With the G-LCD panel's screen center as refernce, adjust the R-LCD and B-LCD panels.

R-LCD

B-LCD

Lock screw "a"

Lock screw "c"

Notch and
hole "c"

Notch and
hole "b"

Lock screw "c"

G-LCD

G-LCD

Lock screw "b"

Notch and hole "c"

Notch and hole "a"

Lock screw "d"

Lock screw "d"

R·B·LCD panel
mounting screws

R·B-LCD

SIDE VIEW (from inside)

SIDE VIEW (from outside)

TOP VIEW SIDE VIEW

G-LCD panel
mounting screws

Eccentric cam
(Y direction adjustment)

Eccentric cam
(X direction adjustment)

Eccentric cam
(θZ direction adjustment)

5. Finally tighten up the convergence lock screw "d".
Notes :

1 The eccentric cam is used for convergence adjustment.

This means that the cam's turning and the linear movement are not always uniform.

2 This model is not equipped with the LCD image adjustment mechanism. This is because the cross-dichroic

prism is used for image formation. When the LCD panels all get into best focus, the images are almost
completely converged.

Convergence and Focus Adjustments Mechanism

XG-NV5XB

21

XG-NV5XB

80

2

2

92

5

7.5

0.5

min85

ø5

ø3.5

3.5

Convergence and Focus Adjustments at a Glance

Adjustment directions

Adjustment Direction Definition Direction of LCD panel

X direction LCD right and left

Convergence Y direction LCD top and bottom

θZ direction Rotation around Z axis LCD turning axis
Z direction LCD optical axis

Focus θX direction Rotation around X axis LCD top-to-bottom flapping

θY direction Rotation around Y axis LCD right-to-left flapping

Convergence and Focus Adjustment for the Optical Mechanism

Color Adjustment Direction

X direction ±0.8mm Eccentric cam Eccentric cam adjusting wrench d Hex wrench

Convergence Y direction ±0.8mm Eccentric cam Eccentric cam adjusting wrench d Hex wrench

R/B θZ direction ±1° Eccentric cam Eccentric cam adjusting wrench d Hex wrench
colors Z direction ±0.8mm

Focus θX direction ±1°

θY direction ±1°

Z direction ±0.2mm

G color Focus θX direction ±1° Same as for R and B colors

θY direction ±1°

Movement

Position Adjusting tool

Notch and hole "a" & "c"
Notch and hole "a" & "c"
Notch and hole "b" & "c"

Eccentric screwdriver, a, c
Bladed screwdriver a, c

Lock screw

b, c

Tightening tool

Phillips
screwdriver,
*Hex wrench

Focus Adjustments the Other Way

Lock screw Position Related direction

a Notch and hole "a" Z and θX directions
b Notch and hole "b" θY direction
c Notch and hole "c" Z, θX and θY directions

Convergence and Focus Adjusting and Tightening Tools

Tool Specific or General Tool code Configuration

Eccentric cam
adjusting wrench

Specific 9DASPN-XGNV1U

Eccentric screwdriver Specific 9DADRiVER-NV4U

100

Hex wrench General (redesigned)

9EQLNC-XGNV1U

5

16

R2

CUT

2

9EQLNC-XGNV4U

Bladed screwdriver General 9EQDRiVER-NV1B

Phillips screwdriver General — For M2.6 pan-head machine screw
*Hex wrench General —

22

1.27mm, preferably use a 70 mm or
longer screwdriver (with a handle).

50

XG-NV5XB

Replacing the LCD panels

Detach the top panel and the optical mechanism unit in advance.

(1)Remove the four prism holder lock screws. Detach the prism holder from the optical mechanism unit.
(2)Remove the LCD panel lock screws (three each for the R-, G- and B-LCD panels). Detach the LCD panels from the

prism holder.

(3)Mount a new LCD panel in the reverse order of the above steps (1) and (2).

~ Readjust the convergence and focus. Note that the G-LCD panel needs no convergence adjustment and has

a small adjustment range in the Z direction.

1

Prism holder

SIDE VIEW (from inside)

Lock screw "d"

R·B-LCD

Optical Mechanism Unit

Lock screw "d"

2

R·B·LCD panel
mounting screws

SIDE VIEW

G-LCD

G-LCD panel
mounting screws

2

23

XG-NV5XB

Adjusting the optical axis of the mirrors (M1, M5 and M4/M6)

The optical axis must be readjusted if an eclipse happens with the R. G or B mirrors. Generally speaking,
this adjustment is needed when any of the internal optical components has been replaced.

Adjustment procedure required when any of the panels has been replaced or the convergence has been
adjusted

(1)Disconnect the flat cables of all the LCD panels.
(2)Let the lamp light up.
(3)To adjust the G mirror, shield the R and B mirrors with shielding plates (You can use a business card or the like to

block the light).
(4)Loosen the lock screw of the M1 adjust lever.
(5)Looking at the G image on the screen, turn or slide the M1 adjust lever until the eclipse on the screen disappears.

Tighten up the screw.
(6)T o adjust the R mirror, shield the G and B mirrors and adjust the M5 adjust lever. For the B mirror, shield the R and

G mirrors and adjust the M6 adjust lever.

(Take the same steps 4 and 5 above.)
(7)Remove all the shielding plates to have a white image.

Make sure there is no eclipse.

M4/M6

Lock screws

Shielding plate B

adjust lever

slide

turn

FRONT

Shielding plate R

M5 adjust lever

turn

Shielding plate G

Lock screws

slide

24

M1 adjust lever

turn

slide

Lock screws

XG-NV5XB

ELECTRICAL ADJUSTMENT

Hook up a signal generator, or a DOSV or Mac personal computer to the projector in order to feed the
signals specified in the Adjusting conditions.

No. Adjusting point Adjusting conditions Adjusting procedure

1 EEPROM

initialization

1. Turn on the power (make
sure the lamp lights up) and
warm up the unit for 15 min­utes.

» Make the following settings:

Press S5001 to call up the process mode and
execute S2 in the SSS menu. Now the system,
with the PC board not included, is initialized. Do
not execute S1 because otherwise the PC board
will be initialized.
To adjust the PC board, follow the instruction in
"Adjusting the PC board". (See page 30)

2 3.3V power

supply
adjustment

3 2.5V power

supply
adjustment

4 R drive 1. Make the following choice.

1. Turn on the power.

2. Connect the digital voltme­ter to TP1446.

1. Turn on the power.

2. Connect the digital voltme­ter to TP1447.

Group : A/D
Subject : GAIN
Make sure the GAIN value
is 163.

2. Feed the 100% red-only sig­nal. Make the following
choice.
Group : A/D
Subject : R-D

» Adjust R1649 so that the voltmeter should read

3.325 V ±100 mV.

» Adjust R1652 so that the voltmeter should read

2.625 V ±50 mV.

» Using the control switches or the remote controller

buttons, adjust the data so that the signal be­comes bit-less (noise).

5 B drive 1. Feed the 100% blue-only

signal. Make the following
choice.
Group : A/D
Subject : B-D

6 G drive 1. Feed the 100% green-only

signal. Make the following
choice.
Group : A/D
Subject : G-D

» Using the control switches or the remote controller

buttons, adjust the data so that the signal be­comes bit-less (noise).

» Using the control switches or the remote controller

buttons, adjust the data so that the signal be­comes bit-less (noise).

25

XG-NV5XB

No. Adjusting point Adjusting conditions Adjusting procedure

7 RGB 1 system

black level
signal amplitude
(odd-numbered)

1. Make the following choice:
Group : OUTPUT 1
Subject : R1-BLK

R1-GAIN

For green, choose the sub-

jects G1-BLK and G1-

GAIN.
For blue, choose the sub­jects B1-BLK and B1-GAIN.

2. Connect the oscilloscope to
TP1101 for red.

TP1201 for green
TP1301 for blue

8 P SIGNAL 1. Connect the oscilloscope to

TP1102 for red.

» Choose the subject R1-GAIN and adjust the sig-

nal amplitude to 3.6 ±0.1 Vp-p using the control
switches or the remote controller buttons.

» Next,choose the subject R-BLK and adjust the black

peak level to 3.2 ±0.1V DC.

3.6Vp-p

(Adjust to 3.3Vp-p
for green and blue.)

3.2V DC
(Adjust to 3.4V DC for green and blue.)

» Adjust the signal's amplitude and maximum black

level to 3.3 ± 0.1Vp-p and 3.4 ± 0.1V DC, respec­tively, for green and blue.

» Adjust the PSIG waveform to the one shown below.

9 Sample-and-

hold pulse
phase
RCK-PHASE
GCK-PHASE
BCK-PHASE

TP1202 for green
TP1302 for blue.

2. Make the following choice:
Group : OUTPUT 2
Subject : PSIG-H

: PSIG-L

1. Feed the XGA mode 75-Hz
black signal.

2. Make the following choice:
Group : OUTPUT 3
Subject : SH-PHASE
(Have the standard level at

8.)
Fix the RCK-, GCK- and
BCK-PHASE settings all to

8.

7.8V DC

PSIG

2.3V DC 5.9V DC

(Adjust with PSIG-L.)(Adjust with PSIG-H.)

GND

» For the green and blue colors, make sure

theirwaveforms are similar to that of the red color.

» Using the control switches or the remote controller

buttons, make sure that the “OUTPUT 3” charac­ters are not blurry and there is no ghost image. If
such blur or ghost occurs, finely adjust the setting
in the range of 7~9.

26

No. Adjusting point Adjusting conditions Adjusting procedure

XG-NV5XB

10 RGB counter-

voltage
adjustment

11 RGB gradation

regeneration
adjustment

1. Feed the black-and-red
(25%) stripe signal (XGA).

2. Make the following choice:
Group : OUTPUT 3
Subject : RC (R)

1. Feed the green-only
SMPTE pattern signal.
Group : OUTPUT 1
Subject : G1-BLK

» Using the control switches or the remote controller

buttons, adjust the data in order to minimize the
flicker.

» Make the same adjustment for BC (B) and GC (G).
» See if the image is equally adjusted at the center

and both sides of the screen. If not, readjust the
setting to have the image equal at right and left.

» Adjust the G-GAIN data until the gradation of the

portion 1 (95% and 100% white) shown below
can be slightly recognized. Make sure also that
the gradation of the portion 2 (0% and 5% black)
is visible.

2

1

12 RGB white

balance

13 Horizontal

center

14 Video picture

adjustment

1. Feed the 32-step gray scale
signal (XGA).
Group : OUTPUT 1
Subject : R1-BLK (R)

B1-BLK (B)

1. Feed the NTSC mono­scope pattern signal.

2. Group : VIDEO 2
Subject : N358-DLY (6)

N443-DLY (2)
PAL-DLY (2)
SECAM-DLY (2)

Make sure the settings are

as above.

3. Group : VIDEO 1
Subject : NTSC-H

1. Feed the split color bar sig­nal.
Group : VIDEO 1
Subject : PICTURE

» Choose the subjects R1-BLK and B1-BLK and

adjust the black balance of the gradation.

» Using the control switches or the remote controller

buttons, adjust the data to have the same
overscan.

» Using the control switches or the remote controller

buttons, adjust the black-to-white (100%) level
difference to 2.0 ±0.02 Vp-p.

2. Connect the oscilloscope
between pin (2) of P801
and GND.

2.0Vp-p

27

XG-NV5XB

No. Adjusting point Adjusting conditions Adjusting procedure

15 V ideo AGC 1. Feed the split color bar sig-

nal.
Group : VIDEO 1
Subject : AGC

2. Connect the oscilloscope
between pin (2) of P801
and GND.

16 Video

brightness
adjustment

1. Feed the baseband (split
color bar) signal. (The ON­AIR signal is not accepted
because of its too much
noise.)
Group : VIDEO 1
Subject : BRIGHT

2. Press the control switch or
the remote control’s mute
button (to set the gamma
correction to the process
setting).

» Using the control switches or the remote controller

buttons, adjust the black-to-white (100%) level
difference to 1.50 ±0.02 Vp-p.

1.50Vp-p

» Using the control switches or the remote controller

buttons, adjust the setting until the black signal
becomes bit-less and set to -2 point of value.

17 Tint 1. Feed the split color bar sig-

nal.
Group : VIDEO 1
Subject : TINT

2. Connect the oscilloscope to
pin (4) of P801.

18 NTSC color

saturation level

1. Feed the split color bar sig­nal.
Group : VIDEO 1
Subject : N-COLOR

2. Connect the oscilloscope to
pin (1) of P801.

» Using the control switches or the remote controller

buttons, adjust the data to have the -(B-Y) wave­form downhill straight.

» Using the control switches or the remote controller

buttons, adjust the difference between the 100%
white portion and the red portion to 0.10 ±0.02 Vp-p.

(same as 100% white)

100% White Red

28

No. Adjusting point Adjusting conditions Adjusting procedure

100% White Red

XG-NV5XB

19 PAL color

saturation level

20 SECAM color

saturation level

21 Video white

balance

1. Feed the PAL color bar sig­nal.
Group : VIDEO 1
Subject : P-COLOR

2. Connect the oscilloscope to
pin (1) of P801.

1. Feed the SECAM color bar
signal.
Group : VIDEO 1
Subject : S-COLOR

2. Connect the oscilloscope to
pin (1) of P801.

1. Feed the NTSC mono­scope pattern signal
Group : VIDEO 2
Subject : R1-GAIN

B1-GAIN

» Using the control switches or the remote controller

buttons, adjust the difference between the 100%
white portion and the red portion to 0.36 ±0.02 Vp-p.

» Using the control switches or the remote controller

buttons, adjust the data to have a level difference
of 0.50 ±0.02 Vp-p between the 100% white
portion and the red portion.

100% White Red

» Using the control switches or the remote controller

buttons, adjust so that the entire screen looks
evenly colorless.

22 Color

23 Color

24 Color system

25 Video system

26 Audio system

irregularity
correction
position

irregularity
correction gain
(in case of
colorirregularity)

performance
check

performance
check

performance
check

1. Feed the gray-only RGB
color signal.

2. Find the color irregularity
position on the screen.

3. Group : NOKO
Subject : NOKO-RL

4. Group : NOKO
Subject : NOKO-LH

1. Feed the gray-only RGB
color signal.

1. Receive the color bar sig­nal.

1. Receive the monoscope
pattern signal.

» If the color is irregular, adjust the NOKO-RL data.

Set it to R for the right-hand color irregularity and to
L for the left-hand one.

» When there is no color irregularity, turn off the

saw-tooth waveform correction on the NOKO-LH
data.

» Adjust R4215 to minimize the right-hand and left-

hand color irregularity.

» In the process mode and select L1. Check the color

and tint.

» In the process mode and select L2. Check the pic-

ture, brightness and sharpness.

» In the process mode nad select L3. Check the bass,

treble.

29

XG-NV5XB

No. Adjusting point Adjusting conditions Adjusting procedure

27 RGB

performance
check

28 Off-timer

performance
check

29 Thermistor

performance
check

30 Automatic

synchronization

31 IrDA

performance
check

32 Keystone

correction
performance
check

1. Receive the RGB signal. » In the process mode and select L4. Check the pic­ture, brightness, red, blue, clock, phase, horizontal
position, and vertical position.

» In the process mode and select OFF. Make sure that

the off-timer starts with “5” (minutes), counts down
each minute in 1 second, and turns off the set at “0”.

1. Heat the thermistor using a

dryer.

1. Receive the PHASE check

pattern signal.

» Make sure the “TEMP” is displayed.

» Call the VGA/SVGA/XGA/SXGA mode and make

sure that the clock, phase, horizontal and vertical
positions can be automatically adjusted.

» Make sure the IrDA signal can be received.

» Make sure the keystone correction functions well.

» Make the following settings.33 Factory settings

Process
adjustment

S4 “Factory setting 4”

Remote controller
setting

ADJUSTING THE PC BOARD (CPCi-0031CE03. PC I/F Unit)

1.Setting the oscilloscope

Set the range to DC 1 V/div and 5µ/div.

2.Connecting the PC interface

1) Connect the PC interface to the projector. Make surethe CON2 (P8404), CON3 (P8502) and CON4
(P8405)connectors are all tight in position.

2) Connect the cable between the computer’s ANALOG OUTPUTterminal and the DSUB (INPUT1 on the
projector)connector.

3) Set the projector’s input selector to the RGB1position.

4) Set the signal generator to the XGA mode (1024 x 768, 60Hz, 32-tone scale). Keep the output amplitude at
700mVp-p.

5) Turn on the power.

3.Adjusting the levels and checking the tones

1) Press the S5001 switch to call up the process mode.

2) Enter 8 for the SH-PHASE setting on the OUTPUT3 menu.
(Adjust to get the on-screen display characters clearand crisp.)

3) Using the BRIGHT setting on the OUTPUT1 menu, adjustthe black level at TP8002 to 1.9 V.

4) Using the ROS setting on the A/D menu, adjust thevoltage at TP8008 (or at pin (2) of IC8011) to 1.7 V.

5) Using the GOS setting on the A/D menu, adjust thevoltage at TP8009 (or at pin (2) of IC8010) to 1.7 V.

6) Using the BOS setting on the A/D menu, adjust thevoltage at TP8010 (or at pin (2) of IC8009) to 1.7 V.

7) Make sure the GAIN setting on the A/D menu is 163.

8) Using the B-D setting on the A/D menu, adjust the whitelevel at TP8001 to 3.6 V. Make sure also the tone
scale(number of tones) is as specified.

9) Using the R-D setting on the A/D menu, adjust the whitelevel at TL75 to 3.6 V. Make sure also the tone
scale(number of tones) is as specified.

10) Using the G-D setting on the A/D menu, adjust the whitelevel at TP8002 to 3.6 V. Make sure also the tone
scale(number of tones) is as specified.

11) Finally press the S5001 switch again to quit theprocess mode.

30

TROUBLE SHOOTING TABLE

Checking the PWB performance

XG-NV5XB

Video input in trouble

Go to "Checking the video unit
circuit".

RGB input in trouble

Feed test pattern signal from
PC.

Is specified cable connected
between PC and projector?

Yes

Is supply voltage as specified?

Yes

Does image appear?

Yes

Go to "Trouble shooting table
for PC I/F unit ".

Through-output in trouble

Through-output circuit in
trouble.

No

Use specified cable.

No

Power circuit in trouble.

No

Check the connectors, starting
from the PC input circuit.

Remote control in trouble

Go to "Checking the remote
control".

31

XG-NV5XB

TROUBLE SHOOTING TABLE (Continued)

Checking the video system

Is the lamp on?

Is specified voltage fed to EA
connectors?

Are there signal inputs at pins (3) and
(29) of P402?

Are there signal outputs at pins (3)
and (6) of IC816?

Yes

Go to "Checking IC801
(RGB signal output circuit)".

No

Yes

No

Yes

No

Yes

No

Check IC816, IC806 and
their peripheral circuits as
well as switching circuit.

Go to "Lamp fails to light-up".

Check the power circuit and its parts.

Are there signals at pin (4) of IC401
and pin (4) of IC402?

Yes

Check the video unit circuit
(IC6004 and its peripheral
circuits).

No

Check the oscillation circuit
of IC401 and IC402, and
their peripheral circuits.

Checking the video unit circuit

Is there video signal output at pin (7)
of IC6001?

Yes

Is there video signal input at IC6004?

Yes

Are there signal outputs at pins (6)
and (8) of IC6004?

Yes

Check the low-pass and buffer circuits
of Q6002 thru Q6008. Is the signal as
specified?

Yes

Go to "Checking IC801 (RGB signal
output circuit)".

No

Check the IC6001 selector switch,
terminal voltage and input circuit.

No

Check the low-pass and buffer
circuits of Q6009 thru Q6015.

No

Check IC6004 and its peripheral
circuits (bias).

No

Check Q6002 thru Q6008 and their
peripheral circuits.

32

TROUBLE SHOOTING TABLE (Continued)

Checking IC801 (RGB signal output circuit)

XG-NV5XB

No

Are there RGB output waveforms at
pins (31), (32) and (33) of IC801?

Go to "No color or unusual tone", "No
Y signal" or "Out of sync".

Are there output waveforms at the
emitters of Q1501, Q1502 and
Q1503?

Are A/D outputs of IC1504, IC1505
and IC1506 as specified?

Go to "Trouble shooting table for PC
I/F unit".

Yes

Yes

Yes

Checking the chroma and Y signals of IC801
(RGB signal output)

No

Check the data transfer and other
performance at pins (17) and (18) of
video IC801.

No

Check IC1501 (amplifier), IC1502
(RGB offset) and their peripheral
circuits.

No

Check the VCLK, IC1504, IC1505,
IC1506 and their peripheral circuits.

Are there signal inputs at pins (12)
(Y signal) and (19)(chroma signal) of
P402?

Yes

Are there output waveforms at pins
(3)(chroma signal) and (6)
(Y signal)of IC816?

Yes

Are there signal inputs at pins (20)
(chroma signal) and (21) (Y signal)
of IC801?

Yes

Go to "Checking IC801 (RGB
signal output circuit)".

No

Go to "Checking the video unit
circuit".

No

Check the IC816 switching and their
peripheral circuits. If there is no signal
at pins (9) and (1) of IC816, check 3-D
noise reduction circuit (IC806).

No

Check IC801 and its peripheral
circuits.

Check IC806 (3-D noise reduction
circuit) and its peripheral circuits.

33

XG-NV5XB

TROUBLE SHOOTING TABLE (Continued)

Checking IC806 (3-D noise reduction circuit)
and its peripheral circuits

Are there signal inputs at pins (40)
(Y signal) and (45)(chroma signal) of
IC806?

Yes

Are there signal outputs at pins (55)
(Y signal) and (51)(chroma signal) of
IC806?

Yes

Are there signal outputs at the
emitters of Q817 (Y signal) and Q910
(chroma signal)?

Yes

Check IC816 and IC801 (RGB signal
output circuit).

No

Check the buffer circuit of Q814 thru
Q816 as well as Q903 thru Q906.

No

Check IC806, IC807 (memory) and
their peripheral circuits.

No

Check the low-pass circuit around
Q817, Q907 and Q910.

No color or unusual tone (NTSC, PAL)

Is there chroma signal input at pin
(20) of IC801?

Yes

Are there signal outputs at pins
(46)(R-Y) and (45)(B-Y) of IC801?

Yes

No

Go back to the signal processing
block.

No

Check the oscillation of X801 and
X802, and their peripheral circuits.

Check IC803, IC814 and their
peripheral circuits.

34

TROUBLE SHOOTING TABLE (Continued)

No or unusual Y signal

XG-NV5XB

Is there Y signal input at pin (21) of
IC801?

Yes

Is there Y signal output at pin (40) of
IC801?

Yes

Is there Y signal output at pin (17) of
IC803?

Yes

Check IC803 and its peripheral
circuits.

No

Go back to the signal processing
block.

No

Check IC801 and its peripheral
circuits.

No

Check IC803 and its peripheral
circuits as well as IC805 (AGC).

No or unusual horizontal sync

Is there horizontal sync pulse output
at pin (56) of IC801?

Yes

Is there horizontal sync pulse output
at pin (9) of IC603?

Yes

No

Check IC801 and its peripheral
circuits.

No

Check the pulse shaping circuit of
IC602 and IC603.

Check IC604 and its peripheral
circuits, and go to "Trouble shooting
table for PC I/F unit".

No or unusual vertical sync

Is there vertical sync pulse output at
pin (4) of IC801?

Yes

Check IC604 and its peripheral
circuits, and go to "Trouble shooting
table for PC I/F unit".

No

Check IC801 and its peripheral
circuits.

35

XG-NV5XB

TROUBLE SHOOTING TABLE (Continued)

Checking the output PWB unit

If there is no signal at SC1501
and SC1502, go to the video
system block.

If there is no signal at SC1404
and SC1405, go to "Trouble
shooting table for PC I/F unit".

Are there signal inputs at
SC1404, SC1405, SC1501 and
SC1502?
Are voltages applied to EA
connectors and SC5502?

Yes

Are there signal outputs at
pins (14) ,(16) and (18) of
IC1401 ?

Yes

Are there signal inputs at pin
(47) of IC1101, IC1201 and
IC1301?

Yes

Are there signal outputs at pins
(17), (19), (21), (27), (29) and
(31) of IC1101, IC1201 and
IC1301?

Yes

NoNo

If there is no signal at EA
connector or SC5502, go to
Checking the power unitblock.

No

Check IC1401 and their
peripheral circuits.

No

Check IC1401 and their
peripheral circuits.

No

Check IC1101,IC1201,IC1301
and their peripheral circuits.

If there is no signal input at
pins (1) and (31) of SC1101,
SC1102 and SC1103, check
the switching circuit and
amplifier circuit of IC1101,
IC1201, IC1301, IC1102,
IC1202, IC1302 and their
peripheral circuits.

Are there signal outputs at pins
(17), (19), (21), (27), (29) and
(31) of IC1102, IC1202 and
IC1302?

Yes

No

Are there signal inputs at
SC1101, SC1201 and
SC1301?

Check the R, G and B panels.

Yes
Yes

No

Check IC1102,IC1202,IC1302
and their peripheral circuits.

No

If there is no signal input at
pins (15) and (30) of
SC1101, SC1102 and
SC1103, check IC1409
and their peripheral
circuits.

Check IC1406, IC1407,
IC1408 and their
peripheral circuits.

36

TROUBLE SHOOTING TABLE (Continued)

No audio output

XG-NV5XB

Are there audio signal inputs at pin
(2) of IC1411?

Are there audio signal outputs at pin
(2) of P5508?

Are there audio signal outputs at pin
(6) of IC7301?

If the voltage at pin (2) of IC7301 is
not as specified, check Q5501,
Q5502 and their peripheral circuits.

No

Yes

No

Yes

No

Yes

Check IC7301 and its peripheral
circuits, and the SP connectors and
speakers.

Checkig the Power Unit

Check the input, the switching circuit
of IC3303 and IC3304, and their
peripheral circuit,SC3001,SC1502,etc.

Check the IC1411 control voltage,and
its peripheral circuits.

Check IC7301 and its peripheral
circuits.

Which output voltage line fails?

Replace ICP751.

Replace IC702, T701 or Q704.

Replace R752.

There is no voltage output at
EA connector.

Yes

Is there any other output
voltage failure?

No

P-FAN Vcc-7

Is EA connector disconnected
or loose?

No

Is AC voltage (85-264V)
applied across the PA
connector?

Yes

Yes

Is Q704 open?

No

Is there short-circuit between
collector and emitter of Q752?

Yes

Yes

Reconnect the EA connector.

No

Replace F701.

No

Replace Q752. Replace PC702.

37

XG-NV5XB

TROUBLE SHOOTING TABLE (Continued)

Power on

Is the right input selected?

Yes

Are the PC, video and LCP cables as
specified and properly connected?

Yes

With the contrast control at maximum,
does the image appear?

No

Is the voltage at CON3 (P8502)
connector as specified?

Yes

Hook up a personal computer.

Does the image appear?

No

Select the right input with remote
control.

No

Use the right cables or reconnect the
cables.

Yes

Readjust the video system.

No

Power circuit faulty.

No

Is the image as specified?

Is the image's color as specified?

A

Does the on-screen display function?

Does the remote control function?

End

Yes

Yes

Yes

Yes

Yes

Go to "Checking the clock circuit and
its peripheral circuits".

No

Check the sync signal circuit and its
peripheral circuits.

No

Check the video circuit and its
peripheral circuits.

No

Go to "Checking the OSD circuit and
its peripheral circuits".

No

Go to "Checking the remote control".

38

Is the lamp out of socket?

Yes

Reconnect the
lamp into socket.

TROUBLE SHOOTING TABLE (Continued)

Lamp fails to light-up

Turn on the power switch. Is

Yes

discharging sound heard from
the lamp?

No

No

No

Check the power circuit.

Replace the
lamp.

Is the ballast cooling fan
running?

Yes

XG-NV5XB

Replace the ballast.

Is DC 360V voltage applied
between PL connector pins?

Yes

Is 2V or higher voltage applied
between pins (1) and (2) of
ballast's D connector?

Is power EA connector
disconnected?

Yes

Reconnect the
connector into socket.

No

Yes

No

No

Check the
microcomputer circuit.

39

XG-NV5XB

Checking the clock circuit and its peripheral circuits

TROUBLE SHOOTING TABLE FOR PC I/F UNIT-1

Is X8001 (6MHz) oscillating?

Yes

Is X8002 (32.768kHz) oscillating?

Yes

Is X8003 (1.84MHz) oscillating?

Yes

Is X8004 (22.165MHz) oscillating?

Yes

Is X8005 (16.25MHz) oscillating?

Yes

Does pin (162) of IC8001 function?

Yes

Check the sync signal circuit and its
peripheral circuits.

Are there signals at pins (46), (48)
and (50) of CON2 (P8404)?

No

No

No

No

No

No

No

X8001 or its peripheral part faulty.

X8002 or its peripheral part faulty.

X8003 or its peripheral part faulty.

X8004 or its peripheral part faulty.

X8005 or its peripheral part faulty.

IC8001 or its peripheral circuit faulty.

LCP circuitry faulty.

Yes

Are there signals at pin (7) of IC8036?

Yes

Are there signals at pins (149) and
(150) of IC8020?

Yes

No

Is the input having a resolution below
S-VGA level or in the video mode?

Yes

Are there signals at pins (26), (28)
and (29) of IC8020?

Yes

Are there signals at pins (14), (16) and
(18) of CON4 (P8405) connector?

Yes

Are there signals at pins (168) thru
(172) of IC8029?

Yes

Are there signals at pins (38) and
(53) of P405?

Yes

No

No

No

No

No

No

IC8023, IC8034, IC8036 or its
peripheral circuit faulty.

IC8025 or its peripheral circuit faulty.

IC8020 or its peripheral circuit faulty.

IC8029 or its peripheral circuit faulty.

IC8025 or its peripheral circuit faulty.

IC8029 or its peripheral circuit faulty.

Go to "Checking the PLL circuit and
its peripheral circuits".

40

TROUBLE SHOOTING TABLE FOR PC I/F UNIT-2

Checking the PLL circuit and its peripheral circuits

XG-NV5XB

Are there signals at pins (6) and (22)
of IC8015?

Yes

Is there signal at pin (18) and (19) of
IC8015?

Yes

Check the video circuit and its
peripheral circuits.

Is image as specified at resolution
above S-VGA level?

Yes

Is image as specified at resolution
below S-VGA level?

Yes

Hook up a video system. Is the
display as specified?

Yes

A

No

IC8025 or its peripheral circuit faulty.

No

IC8015 or its peripheral circuit faulty.

No

Check the S-VGA video circuit and its
peripheral circuits.

No

Check the VGA video circuit and its
peripheral circuits.

No

Check the video system's video
circuit and its peripheral circuits.

41

XG-NV5XB

TROUBLE SHOOTING TABLE FOR PC I/F UNIT-3

Checking the S­VGA's red video
circuit and its
peripheral circuits

Is there signal at pin (13) of IC8004?

Yes

Is there signal at the base of Q8008?

Yes

Is there signal at pin (6) of IC8011

Yes

Are there signals at Pins (21) thru
(27) and (33) thru (40) of IC8011?

Yes

Are there signals at TL44 and TL46?

No No

LCP circuitry faulty.

No No

IC8004 or its peripheral circuit faulty.

No No

Q8008 and Q8009 or there peripheral
circuit faulty.

No No

IC8011 or its peripheral circuit faulty.

No

Checking the VGA's
red video circuit and
its peripheral
circuits

Is there signal at pin (13) of IC8004?

Yes

Is there signal at the base of Q8008?

Yes

Is there signal at pin (6) of IC8011?

Yes

Are there signals at Pins (112) thru
(119) of IC8020?

Yes

B

Yes

Are there signals at pins (1) thru (10)
of IC8051?

Yes

Are there signals at pins (9) and (10)
of CON4 (P8405) connector?

Yes

CON4 (P8405) connector or output
PWB faulty.

IC8025 or its peripheral circuit faulty.

IC8020 or its peripheral circuit faulty.

No

IC8029 or its peripheral circuit faulty.

No

IC8051 or their peripheral parts faulty.

No

Are there signals at Pins (69) thru
(73) and (189) thru (192) of IC8020?

Yes

Check the video
system's red video
circuit and its
peripheral circuits

No

Are there signals at Pins (112) thru
(119) of IC8020?

Yes

42

B

TROUBLE SHOOTING TABLE FOR PC I/F UNIT-4

XG-NV5XB

Checking the S­VGA's green video
circuit and its
peripheral circuits

Is there signal at pin (8) of IC8004?

Yes

Is there signal at the base of Q8006?

Yes

Is there signal at pin (6) of IC8010?

Yes

Are there signals at Pins (21) thru
(27) and (33) thru (40) of IC8010?

Yes

Are there signals at TL45 and TL47?

No No

LCP circuitry faulty.

No No

IC8004 or its peripheral circuit faulty.

No No

Q8006 and Q8007 or there peripheral
circuit faulty.

No No

IC8010 or its peripheral circuit faulty.

No

Checking the VGA's
green video circuit
and its peripheral
circuits

Is there signal at pin (8) of IC8004?

Yes

Is there signal at the base of Q8006?

Yes

Is there signal at pin (6) of IC8010?

Yes

Are there signals at Pins (112) thru
(119) of IC8020?

Yes

C

Yes

Are there signals at pins (11) thru (20)
of IC8051?

Yes

Are there signals at pins (5) and (6) of
CON4 (P8405) connector?

Yes

CON4 (P8405) connector or output
PWB faulty.

IC8025 or its peripheral circuit faulty.

IC8020 or its peripheral circuit faulty.

No

IC 8029 or its perpheral parts faulty.

No

IC8051 or its peripheral parts faulty.

No

Are there signals at Pins (179) thru
(187) of IC8020?

Yes

Check the video
system's green
video circuit and its
peripheral circuits

No

Are there signals at Pins (185) thru
(177) of IC8020?

Yes

43

C

XG-NV5XB

TROUBLE SHOOTING TABLE FOR PC I/F UNIT-5

Checking the S­VGA's blue video
circuit and its
peripheral circuits

Is there signal at pin (3) of IC8004?

Yes

Is there signal at the base of Q8004?

Yes

Is there signal at pin (6) of IC8009?

Yes

Are there signals at Pins (21) thru
(27) and (33) thru (40) of IC8009?

Yes

Are there signals at TL48 and TL49?

No No

LCP circuitry faulty.

No No

IC8004 or its peripheral circuit faulty.

No No

Q8004 and Q8005 or there peripheral
circuit faulty.

No No

IC8009 or its peripheral circuit faulty.

No

Checking the VGA's
blue video circuit
and its peripheral
circuits

Is there signal at pin (3) of IC8004?

Yes

Is there signal at the base of Q8004?

Yes

Is there signal at pin (6) of IC8009?

Yes

Are there signals at Pins (112) thru
(119) of IC8020?

Yes

D

Yes

Are there signal at pins (21) thru (30)
of IC8051?

Yes

Are there signal at pins (1) and (2) of
CON4 (P8405) connector?

Yes

CON4 (P8405) connector or output
PWB faulty.

IC8020 or its peripheral circuit faulty.

IC8020 or its peripheral circuit faulty.

No

IC8018 or its peripheral circuit faulty.

No

IC8051 or their peripheral parts faulty.

No

Are there signals at Pins (74) thru
(83) of IC8020?

Yes

Check the video
system's blue video
circuit and its
peripheral circuits.

No

Are there signals at Pins (85) thru
(93) of IC8020?

Yes

44

D

TROUBLE SHOOTING TABLE FOR PC I/F UNIT-6

Checking the OSD circuit and its peripheral circuits

Display OSD on the screen.

Yes

XG-NV5XB

Are there signals at pins (56), (58),
(71) and (72) of IC8048?

Yes

Are there signals at pins (34), (35)
and (36) of IC8046?

Yes

Are there signals at pins (16) thru
(18) of IC8046?

Yes

IC8036 or its peripheral circuit faulty.

No

IC8029 or its peripheral circuit faulty.

No

IC8048 or its peripheral circuit faulty.

No

IC8048 or its peripheral circuit faulty.

Checking the remote control

Run the remote control. Are there
signals at pin (59) of CON3 (P8502)
connector?

Yes

No

LCD circuitry faulty.

Using remote controller, is there
signal at pin (48) of IC8033?

Yes

Using remote controller, is there
signal at pin (45) of IC8033?

Yes

Using remote controller, is there
signal at pin (60) of CON3 (P8502)
connector?

Yes

LCP-side circuit faulty.

No

IC8001 circuit faulty.

No

IC8033 circuit faulty.

No

IC8033 circuit faulty.

45

CHASSIS LAYOUT

OUTPUT UNIT

H

G

F

DUNTK9839DE05

XG-NV5XB

PC I/F UNIT

CPCI-0031CE03

INLET UNIT

RUNTK0667CEZZ

SIGNAL UNIT

DUNTK9856DE05

E

D

C

S-OUT/REG UNIT

DUNTK9873DE05

IR-DA UNIT

DUNTK9858DE05

VIDEO UNIT

DUNTK9769DE15

PC TERMINAL UNIT

BALLAST UNIT

DUNTK9857DE05

POWER UNIT

CDENC0284CE02

B

RDENC0290CEZZ

A

121110987654321

46

47

BLOCK DIAGRAM

H

G

F

XG-NV5XB

E

D

C

B

A

121110987654321

48

49

OVERALL WIRING DIAGRAM

H

G

F

XG-NV5XB

E

D

C

B

A

121110987654321

50

51

XG-NV5XB

DESCRIPTION OF

WAVEFORMS

SCHEMATIC DIAGRAM

H

G

F

E

D

C

VOLTAGE MEASUREMENT CONDITION:

1. Voltages at test points are measured at the
supply voltage of AC 120V. Signals are fed by a
color bar signal generator for servicing purpose and
the above voltages are measured with a 20k ohm/
V tester.

WAVEFORM MEASUREMENT CONDI­TION:

1. Waveforms at test points are observed at the supply
voltage of AC 120V. Signals are fed by a color bar
signal generator for servicing purpose.

INDICATION OF RESISTOR & CAPACI­TOR:

RESISTOR

1. The unit of resistance “Ω” is omitted.
(K=kΩ=1000 Ω, M=MΩ).

2. All resistors are ± 5%, unless otherwise noted.
(J= ± 5%, F= ± 1%, D= ± 0.5%)

3. All resistors are 1/10W, unless otherwise noted.

4. All resistors are Carbon type, unless otherwise
noted.

C : Solid
S : Oxide Film T : Special
N : Metal Coating

CAPACITOR

1. All capacitors are µF, unless otherwise noted.
(P=pF=µµF).

2. All capacitors are 50V, unless otherwise noted.

3. All capacitors are Ceramic type, unless otherwise
noted.

(ML): Mylar (TA): Tantalum
(PF): Polypro Film (ST): Styrol

CAUTION:

This circuit diagram is original one, therefore there may be a
slight difference from yours.

W

: Cement

1 SC1101 7-pin

(RP SIG5)
H : 10µsec/div
V : 2V/div

5 SC1301 7-pin

(BP SIG5)
H : 10µsec/div
V : 2V/div

9 P801 4-pin

(B-Y)
H : 20µsec/div
V : 1V/div

2 SC1101 8-pin

(RP SIG6)
H : 10µsec/div
V : 2V/div

6 SC1301 8-pin

(BP SIG6)
H : 10µsec/div
V : 2V/div

0 IC604 6-pin

(H-OUT)
H : 20µsec/div
V : 1V/div

3 SC1201 7-pin

(GP SIG5)
H : 10µsec/div
V : 2V/div

7 P801 1-pin

(R)
H : 10µsec/div
V : 0.5V/div

q Q422 Emitter

(4FSC)
H : 50µsec/div
V : 0.5V/div

4 SC1201 8-pin

(GP SIG6)
H : 10µsec/div
V : 2V/div

8 P801 2-pin

(G)
H : 20µsec/div
V : 0.5V/div

w Q6008 Emitter

(Y-signal)
H : 10µsec/div
V : 0.2V/div

SAFETY NOTES:

1. DISCONNECT THE AC PLUG FROM THE AC

B

A

OUTLET BEFORE REPLACEING PARTS.

2. SEMICONDUCTOR HEAT SINKS SHOULD BE
REGARDED AS POTENTIAL SHOCK HAZARDS
WHEN THE CHASSIS IS OPERATING.

IMPORTANT SAFETY NOTICE:

PARTS MARKED WITH “å” ( ) ARE
IMPORTANT FOR MAINTAINING THE SAFETY OF
THE SET. BE SURE TO REPLACE THESE PARTS
WITH SPECIFIED ONES FOR MAINTAINING THE
SAFETY AND PERFORMANCE OF THE SET.

52

e Q6003 Emitter

(CHROMA signal)
H : 10µsec/div
V : 0.2V/div

121110987654321

53

XG-NV5XB

Ë

SIGNAL UNIT-1/2

H

G

F

E

D

C

B

A

121110987654321

54

55

XG-NV5XB

Ë

IR-DA and SIGNAL UNIT-2/2

H

G

F

E

D

C

B

A

121110987654321

56

57

XG-NV5XB

Ë

OUTPUT UNIT-1/5 (Drawing with small PWB attached: 2 )

H

G

F

E

D

C

B

A

121110987654321

58

59

XG-NV5XB

Ë

OUTPUT UNIT-2/5 (Drawing with small PWB attached: 2 )

H

G

F

E

D

C

B

A

121110987654321

60

61

XG-NV5XB

Ë

OUTPUT UNIT-3/5 (Drawing with small PWB attached: 2 )

H

G

F

E

D

Small PWB input section

C

B

A

121110987654321

62

63

XG-NV5XB

Ë

OUTPUT UNIT-4/5 (Drawing with small PWB attached: 2 )

H

G

F

E

D

C

B

A

121110987654321

64

65

XG-NV5XB

Ë

OUTPUT UNIT-5/5 (Drawing with small PWB attached: 2 )

H

G

F

E

D

C

B

A

121110987654321

66

67

XG-NV5XB

Ë

OUTPUT SMALL PWB

H

G

F

E

D

C

B

A

121110987654321

68

69

XG-NV5XB

Ë

OUTPUT UNIT-1/5 (Drawing with small PWB integrated: 3 )

H

G

F

E

D

C

B

A

121110987654321

70

71

XG-NV5XB

Ë

OUTPUT UNIT-2/5 (Drawing with small PWB integrated:

H

G

F

)

3

E

D

C

B

A

121110987654321

72

73

XG-NV5XB

Ë

OUTPUT UNIT-3/5 (Drawing with small PWB integrated: 3 )

H

G

F

E

D

C

B

A

121110987654321

74

75

XG-NV5XB

Ë

OUTPUT UNIT-4/5 (Drawing with small PWB integrated: 3 )

H

G

F

E

D

C

B

A

121110987654321

76

77

XG-NV5XB

Ë

OUTPUT UNIT-5/5 (Drawing with small PWB integrated: 3 )

H

G

F

E

D

C

B

A

121110987654321

78

79

XG-NV5XB

Ë

VIDEO UNIT

H

G

F

E

D

C

B

A

121110987654321

80

81

XG-NV5XB

Ë

PC TERMINAL UNIT

H

G

F

E

D

C

B

A

121110987654321

82

83

XG-NV5XB

Ë

SOUND OUT/REGULATOR UNIT

H

G

F

E

D

C

B

A

121110987654321

84

85

XG-NV5XB

Ë

OPERATION KEY UNIT

H

G

F

E

D

C

B

A

121110987654321

86

87

Ë

INLET and POWER UNIT-A

(INLET)

XG-NV5XB

H

G

F

RUNTK0667CEZZ

(POWER)PWB-A

CDENC0284CE02

E

D

C

B

A

88

121110987654321

89

Ë

POWER UNIT-B

XG-NV5XB

H

PWB-B

CDENC0284CE02

G

F

E

D

C

B

A

90

121110987654321

91

XG-NV5XB

Ë

POWER UNIT-C

PWB-C

H

CDENC0284CE02

G

F

E

D

C

B

A

121110987654321

92

93

XG-NV5XB

Ë

PC I/F UNIT-1/8

H

G

F

E

D

C

B

A

121110987654321

94

95

XG-NV5XB

Ë

PC I/F UNIT-2/8

H

G

F

E

D

C

B

A

121110987654321

96

97

XG-NV5XB

Ë

PC I/F UNIT-3/8

H

G

F

E

D

C

B

A

121110987654321

98

99

XG-NV5XB

Ë

PC I/F UNIT-4/8

H

G

F

E

D

C

B

A

121110987654321

100

101

XG-NV5XB

Ë

PC I/F UNIT-5/8

H

G

F

E

D

C

B

A

121110987654321

102

103

XG-NV5XB

Ë

PC I/F UNIT-6/8

H

G

F

E

D

C

B

A

121110987654321

104

105

XG-NV5XB

Ë

PC I/F UNIT-7/8

H

G

F

E

D

C

B

A

121110987654321

106

107

XG-NV5XB

Ë

PC I/F UNIT-8/8

H

G

F

E

D

C

B

A

121110987654321

108

109

XG-NV5XB

PRINTED WIRING BOARD ASSEMBLIS

H

G

F

E

Signal Unit (Wiring Side)

D

C

PC Terminal Unit (Wiring Side)

B

A

IR-DA Unit (Wiring Side)

Video Unit (Wiring Side)

654321

110

XG-NV5XB

H

G

F

E

Signal Unit (Component Side)

D

C

PC Terminal Unit (Component Side)

B

A

Video Unit (Component Side)

IR-DA Unit (Component Side)

654321

111

XG-NV5XB

H

G

Output Small PWB

F

(Wiring Side)

E

D

C

B

A

Output Unit (Wiring Side)

(Drawing with small PWB attached:2)

654321

112

XG-NV5XB

H

G

Output Small PWB

(Component Side)

F

E

D

C

B

A

Output Unit (Component Side)

(Drawing with small PWB attached:2)

654321

113

XG-NV5XB

H

G

F

E

D

C

B

A

Output Unit (Wiring Side)

(Drawing with small PWB attached:3)

654321

114

XG-NV5XB

H

G

F

E

D

C

B

A

Output Unit (Component Side)

(Drawing with small PWB attached:3)

654321

115

XG-NV5XB

H

G

F

E

D

C

B

A

PC I/F Unit (Wiring Side)

654321

116

XG-NV5XB

H

G

F

E

D

C

B

A

PC I/F Unit (Component Side)

654321

117

XG-NV5XB

H

G

F

PWB-A

E

D

C

B

PWB-B

PWB-C

Power Unit (Wiring Side)

A

654321

118

XG-NV5XB

H

G

F

PWB-A

E

D

C

B

PWB-B

PWB-C

Power Unit (Component Side)

A

654321

119

XG-NV5XB

H

G

F

E

Inlet Unit (Wiring Side)

D

C

B

Inlet Unit (Component Side)

A

654321

120

XG-NV5XB

H

G

F

E

Operation Key Unit (Wiring Side)

D

C

B

Operation Key Unit (Component Side)

A

654321

121

XG-NV5XB

H

G

F

E

S-Out/REG Unit (Wiring Side)

D

C

B

S-Out/REG Unit (Component Side)

A

654321

122

XG-NV5XB

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

PARTS LIST

PARTS REPLACEMENT

Parts marked with "å" are important for maintaining the safety of
the set. Be sure to replace these parts with specified ones for main­taining the safety and performance of the set.

Les pieces marquées "å" sont importantes pour maintenir la sécurité
de l'appareil. Ne remplacer ces pieces que par des pieces dont le
numéro est spécifié pour maintenir la sécurité et protéger le bon
fonctinnement de l'appareil.

"HOW TO ORDER REPLACEMENT PARTS"

To have your order filled promptly and correctly, please furnish the
following informations.

1. MODEL NUMBER 2. REF. NO.

3. PART NO. 4. DESCRIPTION

5. CODE 6. QUANTITY

in USA: Contact your nearest SHARP Parts Distributor.

For location of SHARP Parts Distributor,
Please call Toll-Free; 1-800-BE-SHARP

in CANADA: Contact SHARP Electronics of Canada Limited

Phone [phone].

★ MARK: SPARE PARTS-DELIVERY SECTION

Ref. No. Part No. ★ Description Code

LCD PANELS

NOTE: THE PARTS HERE SHOWN ARE SUPPLIED AS AN

ASSEMBLY BUT NOT INDEPENDENTLY.

RLCDP0073CEZZ J LCD Module Unit, Red CZ
RLCDP0074CEZZ J LCD Module Unit, Green CZ
RLCDP0075CEZZ J LCD Module Unit, Blue CZ

PRINTED WIRING BOARD ASSEMBLIES

(NOT REPLACEMENT ITEM)

DUNTK9856DE05 – Signal Unit —
DUNTK9839DE05 – Output Unit —
DUNTK9769DE15 – Video Unit —
DUNTK9857DE05 – PC Terminal Unit —
DUNTK9858DE05 – IR-DA Unit —
DUNTK9873DE05 – Sound Out/Regulator Unit —
RUNTK0667CEZZ – Inlet Unit —
CDENC0284CE02 – Power Unit —
CPCI-0031CE03 – PC I/F Unit —

IC401 VHiNJM2240M-1 J NJM2240M AG
IC402 VHiNJM2240M-1 J NJM2240M AG
IC406 VHiBA7046F/-1 J BA7046F AF
IC409 VHiMM1041XM-1 J MM1041XMR AG
IC418 VHiTC4W53U/-1 J TC4W53FU AF
IC602 VHiTHC4538T-1 J TC74HC4538AFT AL
IC603 VHiTHC4538T-1 J TC74HC4538AFT AL
IC604 VHiSNHC153T-1 J SN74HC153PW AK
IC605 VHiSNHC153T-1 J SN74HC153PW AK
IC801 VHiTDA8854H-2 J TDA8854H/N2 BD
IC803 VHiTDA4565/-1 J TDA4565/V6 AN
IC805 VHiNJM2060V-1 J NJM2060V AF
IC806 VHiTC90A11F-1 J TC90A11F AZ
IC807 VHiM518221S-1 J MSM518221-30JS BA
IC808 VHiPST600DM-1 J IC-PST600DMT AE
IC814 VHiTA8814N/-1 J TA8814N AV
IC816 VHiNJM2283V-1 J NJM2283V AG
IC1001 VHiPQ20VZ11-1 J PQ20VZ11 AH

Q411 VS2PD601AR/-1 J 2PD601AR AB
Q412 VS2SB1132Q/-1 J 2SB1132Q AC
Q416 VS2PD601AR/-1 J 2PD601AR AB
Q420 VS2SC2411KR-1 J 2SC2411KR AC
Q421 VS2SC2411KR-1 J 2SC2411KR AC
Q422 VS2SC2411KR-1 J 2SC2411KR AC
Q804 VS2PB709AR/-1 J 2PB709AR AB
Q805 VS2PD601AR/-1 J 2PD601AR AB
Q806 VS2PD601AR/-1 J 2PD601AR AB
Q808 VS2PD601AR/-1 J 2PD601AR AB
Q809 VS2PB709AR/-1 J 2PB709AR AB
Q810 VS2PB709AR/-1 J 2PB709AR AB
Q814 VS2PD601AR/-1 J 2PD601AR AB
Q815 VS2PB709AR/-1 J 2PB709AR AB
Q816 VS2PD601AR/-1 J 2PD601AR AB
Q817 VS2PD601AR/-1 J 2PD601AR AB
Q819 VSDTC144EK/-1 J DTC144EK AB
Q820 VS2PD601AR/-1 J 2PD601AR AB
Q821 VS2PB709AR/-1 J 2PB709AR AB
Q822 VSDTC114EK/-1 J DTC114EK AB
Q823 VS2SC2411KR-1 J 2SC2411KR AC
Q824 VS2SC2411KR-1 J 2SC2411KR AC
Q825 VS2SC2411KR-1 J 2SC2411KR AC
Q903 VS2PB709AR/-1 J 2PB709AR AB
Q905 VS2PD601AR/-1 J 2PD601AR AB
Q906 VS2PD601AR/-1 J 2PD601AR AB
Q907 VS2PD601AR/-1 J 2PD601AR AB
Q910 VS2PD601AR/-1 J 2PD601AR AB

D404 RH-EX0519CEZZ J Zener Diode AB
D801 VHDMA152WA/-1 J Diode MA152WA AA
D802 RH-EX0226CEZZ J Zener Diode AB
D803 RH-EX0226CEZZ J Zener Diode AB
D805 VHDDAN202K/-1 J Diode DAN202K AB
D1005 VHDDAN202K/-1 J Diode DAN202K AB

X801 RCRSB0009PEZZ J Crystal AL
X802 RCRSB0008PEZZ J Crystal AH

DUNTK9856DE05

SIGNAL UNIT

INTEGRATED CIRCUITS

TRANSISTORS

DIODES

PACKAGED CIRCUITS

L401 VP-CF390K0000 J Peaking 39µH AB
L904 VP-1M330J4R2N J Peaking 33µH AC
L905 VP-1M270J3R8N J Peaking 27µH AC
L906 VP-1M330J4R2N J Peaking 33µH AC
L908 VP-1M220J2R9N J Peaking 22µH AC

CAPACITORS

COILS

C404 VCKYCY1EF104Z J 0.1 25V Ceramic AA

123

XG-NV5XB

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

DUNTK9856DE05

SIGNAL UNIT (Continued)

C414 VCKYCY1HB103K J 0.01 50V Ceramic AA
C416 VCKYCY1AF105Z J 1.0 10V Ceramic AC
C423 VCEAPF1CW106M J 10 16V Electrolytic AB
C425 VCKYCY1HB103K J 0.01 50V Ceramic AA
C437 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C441 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C443 VCKYCY1HF102Z J 1000p 50V Ceramic AA
C447 VCCCCY1HH5R0C J 5.0p 50V Ceramic AA
C448 VCEAPF1HW475M J 4.7 50V Electrolytic AB
C450 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C451 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C452 VCKYCY1HF102Z J 1000p 50V Ceramic AA
C453 VCEAPF1CW106M J 10 16V Electrolytic AB
C454 VCCCCY1HH7R0D J 7.0p 50V Ceramic AA
C455 VCEAPF1CW226M J 22 16V Electrolytic AB
C456 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C458 VCKYCY1HB103K J 0.01 50V Ceramic AA
C472 VCEAPF0JW476M J 47 6.3V Electrolytic AB
C485 VCEAPF1HW475M J 4.7 50V Electrolytic AB
C486 VCKYCY1HB103K J 0.01 50V Ceramic AA
C487 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C488 VCKYCY1HB103K J 0.01 50V Ceramic AA
C489 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C490 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C491 VCCCCY1EH102J J 1000p 25V Ceramic AB
C495 VCEAPF1CW226M J 22 16V Electrolytic AB
C601 VCEAPF1HW105M J 1.0 50V Electrolytic AB
C602 VCFRED1HM472J J 4700p 50V Mylar AD
C603 VCFRED1HM222J J 2200p 50V Mylar AC
C606 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C607 VCCCCY1EH102J J 1000p 25V Ceramic AB
C608 VCCCCY1EH102J J 1000p 25V Ceramic AB
C609 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C610 VCCCCY1EH102J J 1000p 25V Ceramic AB
C611 VCCCCY1EH102J J 1000p 25V Ceramic AB
C612 VCEAPF0JW476M J 47 6.3V Electrolytic AB
C613 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C650 RC-KZ0416CEZZ J 10 25V Ceramic AE
C810 VCCCCY1HH180J J 18p 50V Ceramic AA
C811 VCCCCY1HH180J J 18p 50V Ceramic AA
C812 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C814 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C815 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C816 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C817 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C818 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C819 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C822 VCCCCY1HH470J J 47p 50V Ceramic AA
C823 VCCCCY1HH470J J 47p 50V Ceramic AA
C824 VCCCCY1HH221J J 220p 50V Ceramic AA
C825 VCCCCY1HH221J J 220p 50V Ceramic AA
C826 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C827 VCE9PF1HW105M J 1.0 50V Elect.(N.P) AC
C828 VCE9PF1HW105M J 1.0 50V Elect.(N.P) AC
C829 VCEAPF1CW226M J 22 16V Electrolytic AB
C830 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C831 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C832 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C833 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C834 VCFRED1HM332J J 3300p 50V Mylar AD
C835 VCEAPF1CW107M J 100 16V Electrolytic AD
C836 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C837 VCEAPF1CW107M J 100 16V Electrolytic AD
C838 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C839 VCEAPF1HW225M J 2.2 50V Electrolytic AB
C840 VCFYEC1CM223J J 0.022 16V Mylar AC
C844 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C845 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C852 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C856 VCFYEC1CM274J J 0.27 16V Mylar AE
C857 VCKYCY1HB103K J 0.01 50V Ceramic AA
C860 VCCCCY1HH221J J 220p 50V Ceramic AA

C861 VCE9PF1CW106M J 10 16V Elect.(N.P) AC
C862 VCCCCY1HH390J J 39p 50V Ceramic AA
C863 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C864 VCE9PF1HW105M J 1.0 50V Elect.(N.P) AC
C865 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C866 VCEAPF0JW476M J 47 6.3V Electrolytic AB
C867 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C868 VCKYCY1HB103K J 0.01 50V Ceramic AA
C869 VCKYCY1CF224Z J 0.22 16V Ceramic AA
C870 VCCCCY1HH101J J 100p 50V Ceramic AA
C871 VCKYCY1HB103K J 0.01 50V Ceramic AA
C872 VCEAPF1CW106M J 10 16V Electrolytic AB
C873 VCFYEC1CM274J J 0.27 16V Mylar AE
C877 VCEAPF1CW106M J 10 16V Electrolytic AB
C878 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C879 VCEAPF1CW106M J 10 16V Electrolytic AB
C880 VCE9PF1CW106M J 10 16V Elect.(N.P) AC
C881 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C882 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C883 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C885 VCCCCY1HH470J J 47p 50V Ceramic AA
C891 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C892 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C893 VCEAPF1HW225M J 2.2 50V Electrolytic AB
C903 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C904 VCCCCY1HH120J J 12p 50V Ceramic AA
C905 VCCCCY1HH360J J 36p 50V Ceramic AA
C906 VCEAPF1HW105M J 1.0 50V Electrolytic AB
C907 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C908 VCKYCY1HB103K J 0.01 50V Ceramic AA
C909 VCKYCY1HB103K J 0.01 50V Ceramic AA
C910 VCCCCY1HH181J J 180p 50V Ceramic AA
C911 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C912 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C913 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C914 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C915 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C916 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C917 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C918 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C919 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C920 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C921 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C922 VCEAPF1CW106M J 10 16V Electrolytic AB
C923 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C924 RC-EZ0569CEZZ J 10 10V Electrolitic AF
C925 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C926 VCCCCY1HH220J J 22p 50V Ceramic AA
C927 VCCCCY1HH5R0C J 5.0p 50V Ceramic AA
C930 VCCCCY1HH330J J 33p 50V Ceramic AA
C931 VCCCCY1HH470J J 47p 50V Ceramic AA
C932 VCKYCY1AF105Z J 1.0 10V Ceramic AC
C933 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C934 VCE9PF1CW106M J 10 16V Elect.(N.P) AC
C935 VCCCCY1HH390J J 39p 50V Ceramic AA
C936 VCEAPF1CW106M J 10 16V Electrolytic AB
C937 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C938 VCKYCY1HB103K J 0.01 50V Ceramic AA
C939 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C945 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C946 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C948 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C949 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C950 VCKYCY1HB103K J 0.01 50V Ceramic AA
C951 VCKYCY1HB103K J 0.01 50V Ceramic AA
C954 VCKYCY1HB103K J 0.01 50V Ceramic AA
C957 VCEAPF0JW476M J 47 6.3V Electrolytic AB
C958 VCEAPF0JW476M J 47 6.3V Electrolytic AB
C959 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C960 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C962 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C963 VCEAPF1CW226M J 22 16V Electrolytic AB
C964 VCFYEC1CM104J J 0.1 16V Mylar AD
C965 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C966 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C967 VCKYCY1CF104Z J 0.1 16V Ceramic AA

124

XG-NV5XB

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

DUNTK9856DE05

SIGNAL UNIT (Continued)

C968 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C970 VCKYCY1HB103K J 0.01 50V Ceramic AA
C973 VCCCCY1HH391J J 390p 50V Ceramic AA
C1009 RC-EZ0569CEZZ J 10 10V Electrolitic AF

RESISTORS

R410 VRS-CY1JF273J J 27k 1/16W Metal Oxide AA
R411 VRS-CY1JF471J J 470 1/16W Metal Oxide AA
R412 VRS-CY1JF822J J 8.2k 1/16W Metal Oxide AA
R413 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R414 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R415 VRS-CY1JF151J J 150 1/16W Metal Oxide AA
R416 VRS-CY1JF562J J 5.6k 1/16W Metal Oxide AA
R417 VRS-CY1JF331J J 330 1/16W Metal Oxide AA
R418 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R419 VRS-CY1JF471J J 470 1/16W Metal Oxide AA
R438 VRS-CY1JF474J J 470k 1/16W Metal Oxide AA
R439 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R440 VRS-CY1JF331J J 330 1/16W Metal Oxide AA
R460 VRS-CY1JF331J J 330 1/16W Metal Oxide AA
R472 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R477 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R478 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R479 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R480 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R481 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R482 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R496 VRS-CY1JF361J J 360 1/16W Metal Oxide AA
R497 VRS-CY1JF332F J 3.3k 1/16W Metal Oxide AA
R503 VRS-CY1JF392F J 3.9k 1/16W Metal Oxide AA
R505 VRS-CY1JF361J J 360 1/16W Metal Oxide AA
R584 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R603 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R604 VRS-CY1JF562J J 5.6k 1/16W Metal Oxide AA
R605 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R608 VRS-CY1JF152J J 1.5k 1/16W Metal Oxide AA
R611 VRN-CY1JF133D J 13k 1/16W Metal Film AB
R613 VRN-CY1JF752D J 7.5k 1/16W Metal Film AA
R614 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R615 VRS-CY1JF182J J 1.8k 1/16W Metal Oxide AA
R616 VRN-CY1JF682D J 6.8k 1/16W Metal Film AB
R617 VRN-CY1JF103D J 10k 1/16W Metal Film AA
R619 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R621 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R622 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R623 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R624 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R650 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R657 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R699 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R806 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R807 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R808 VRS-CY1JF561J J 560 1/16W Metal Oxide AA
R811 VRS-CY1JF681J J 680 1/16W Metal Oxide AA
R812 VRS-CY1JF183J J 18k 1/16W Metal Oxide AA
R815 VRS-TX2HF5R6J J 5.6 1/2W Metal Oxide AA
R816 VRS-CY1JF104J J 100k 1/16W Metal Oxide AA
R817 VRS-TX2HF4R7J J 4.7 1/2W Metal Oxide AB
R819 VRS-CY1JF392J J 3.9k 1/16W Metal Oxide AA
R820 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R821 VRS-CY1JF473J J 47k 1/16W Metal Oxide AA
R832 VRS-TX2HF4R7J J 4.7 1/2W Metal Oxide AB
R835 VRS-CY1JF393J J 39k 1/16W Metal Oxide AA
R837 VRS-CY1JF564J J 560k 1/16W Metal Oxide AA
R838 VRS-CY1JF333J J 33k 1/16W Metal Oxide AA
R839 VRS-CY1JF104J J 100k 1/16W Metal Oxide AA
R840 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R841 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R842 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R843 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R844 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R845 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA

R846 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R848 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R849 VRS-CY1JF472J J 4.7k 1/16W Metal Oxide AA
R850 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R851 VRS-CY1JF822J J 8.2k 1/16W Metal Oxide AA
R852 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R853 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R855 VRS-CY1JF221J J 220 1/16W Metal Oxide AA
R856 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R857 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R858 VRS-CY1JF222J J 2.2k 1/16W Metal Oxide AA
R859 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R860 VRS-CY1JF822J J 8.2k 1/16W Metal Oxide AA
R861 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R862 VRS-CY1JF472J J 4.7k 1/16W Metal Oxide AA
R863 VRS-CY1JF473J J 47k 1/16W Metal Oxide AA
R865 VRS-CY1JF682J J 6.8k 1/16W Metal Oxide AA
R866 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R867 VRS-CY1JF183J J 18k 1/16W Metal Oxide AA
R869 VRS-CY1JF223J J 22k 1/16W Metal Oxide AA
R870 VRS-CY1JF682J J 6.8k 1/16W Metal Oxide AA
R871 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R872 VRS-CY1JF472J J 4.7k 1/16W Metal Oxide AA
R873 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R874 VRS-CY1JF683J J 68k 1/16W Metal Oxide AA
R875 VRS-CY1JF224J J 220k 1/16W Metal Oxide AA
R876 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R877 VRS-CY1JF472J J 4.7k 1/16W Metal Oxide AA
R878 VRS-CY1JF682J J 6.8k 1/16W Metal Oxide AA
R879 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R880 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R891 VRS-CY1JF682J J 6.8k 1/16W Metal Oxide AA
R892 VRS-CY1JF273J J 27k 1/16W Metal Oxide AA
R893 VRS-CY1JF392J J 3.9k 1/16W Metal Oxide AA
R894 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R895 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R898 VRS-CY1JF333J J 33k 1/16W Metal Oxide AA
R901 VRS-CY1JF223J J 22k 1/16W Metal Oxide AA
R902 VRS-CY1JF223J J 22k 1/16W Metal Oxide AA
R903 VRS-CY1JF821J J 820 1/16W Metal Oxide AA
R905 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R906 VRS-TV1JD122J J 1.2k 1/16W Metal Oxide AA
R907 VRS-CY1JF223J J 22k 1/16W Metal Oxide AA
R908 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R909 VRN-CY1JF102D J 1.0k 1/16W Metal Film AB
R910 VRS-TV1JD122J J 1.2k 1/16W Metal Oxide AA
R911 VRS-TV1JD471J J 470 1/16W Metal Oxide AA
R912 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R913 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R914 VRS-CY1JF821J J 820 1/16W Metal Oxide AA
R915 VRN-CY1JF332D J 3.3k 1/16W Metal Film AA
R916 VRN-CY1JF332D J 3.3k 1/16W Metal Film AA
R917 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R918 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R919 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R920 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R922 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R923 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R924 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R925 VRS-TV1JD222J J 2.2k 1/16W Metal Oxide AA
R926 VRS-CY1JF823J J 82k 1/16W Metal Oxide AA
R927 VRS-CY1JF473J J 47k 1/16W Metal Oxide AA
R928 VRS-CY1JF471J J 470 1/16W Metal Oxide AA
R929 VRS-CY1JF561J J 560 1/16W Metal Oxide AA
R930 VRS-CY1JF223J J 22k 1/16W Metal Oxide AA
R931 VRS-CY1JF223J J 22k 1/16W Metal Oxide AA
R932 VRS-CY1JF152J J 1.5k 1/16W Metal Oxide AA
R933 VRS-CY1JF681J J 680 1/16W Metal Oxide AA
R934 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R935 VRS-CY1JF273J J 27k 1/16W Metal Oxide AA
R936 VRS-TX2HF5R6J J 5.6 1/2W Metal Oxide AA
R937 VRS-CY1JF273J J 27k 1/16W Metal Oxide AA
R938 VRS-CY1JF471J J 470 1/16W Metal Oxide AA
R939 VRS-CY1JF822J J 8.2k 1/16W Metal Oxide AA
R940 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R941 VRS-CY1JF331J J 330 1/16W Metal Oxide AA

125

XG-NV5XB

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

DUNTK9856DE05

SIGNAL UNIT (Continued)

R942 VRS-CY1JF750J J 75 1/16W Metal Oxide AA
R943 VRS-CY1JF471J J 470 1/16W Metal Oxide AA
R944 VRS-CY1JF562J J 5.6k 1/16W Metal Oxide AA
R945 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R953 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R954 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R955 VRS-CY1JF471J J 470 1/16W Metal Oxide AA
R956 VRS-CY1JF681J J 680 1/16W Metal Oxide AA
R957 VRS-CY1JF154J J 150k 1/16W Metal Oxide AA
R958 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R959 VRS-TV1JD222J J 2.2k 1/16W Metal Oxide AA
R964 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R975 VRS-TX2HF5R6J J 5.6 1/2W Metal Oxide AA
R976 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R980 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R981 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R982 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R983 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R990 VRS-CY1JF104J J 100k 1/16W Metal Oxide AA
R991 VRS-CY1JF104J J 100k 1/16W Metal Oxide AA
R999 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1005 VRS-TX2HF5R6J J 5.6 1/2W Metal Oxide AA
R1006 VRS-TX2HF5R6J J 5.6 1/2W Metal Oxide AA
R1007 VRN-CY1JF562D J 5.6k 1/16W Metal Film AB
R1008 VRN-CY1JF102D J 1.0k 1/16W Metal Film AB
R1009 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1801 VRS-CY1JF223J J 22k 1/16W Metal Oxide AA
R1802 VRS-CY1JF333J J 33k 1/16W Metal Oxide AA
R1803 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1804 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1805 VRS-CY1JF102F J 1.0k 1/16W Metal Oxide AA
R1806 VRS-CY1JF102F J 1.0k 1/16W Metal Oxide AA
R1807 VRS-CY1JF122J J 1.2k 1/16W Metal Oxide AA
R1808 VRS-CY1JF821J J 820 1/16W Metal Oxide AA
R1809 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1810 VRS-CY1JF122J J 1.2k 1/16W Metal Oxide AA
R1811 VRS-CY1JF122J J 1.2k 1/16W Metal Oxide AA
R1812 VRS-CY1JF104J J 100k 1/16W Metal Oxide AA
R1813 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1819 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1820 VRS-CY1JF152J J 1.5k 1/16W Metal Oxide AA
R1822 VRS-CY1JF822J J 8.2k 1/16W Metal Oxide AA
R1823 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1825 VRS-CY1JF391J J 390 1/16W Metal Oxide AA
R1826 VRS-CY1JF000J J 0 1/16W Metal Oxide AA

MISCELLANEOUS PARTS

FB401 RBLN-0065CEZZ J Ferrite Bead AB
FB402 RBLN-0065CEZZ J Ferrite Bead AB
FB901 RBLN-0065CEZZ J Ferrite Bead AB
FB902 RBLN-0065CEZZ J Ferrite Bead AB
FB903 RBLN-0065CEZZ J Ferrite Bead AB
FB904 RBLN-0065CEZZ J Ferrite Bead AB
P401 QPLGZ3044CEZZ J Plug, 30-pin (TN) AH
P402 QPLGZ3044CEZZ J Plug, 30-pin (VS) AH
P801 QPLGN0463TAZZ J Plug, 4-pin AC
P1501 QPLGZ2026CEZZ J Plug, 20-pin AE
P1502 QPLGZ2026CEZZ J Plug, 20-pin AE

DUNTK9839DE05

OUTPUT UNIT

INTEGRATED CIRCUITS

IC1004 RH-iX2204CEZZ J PQ12TZ11 AG
IC1101 VHiCXA2112R-1 J CXA2112R-T6 BB
IC1102 VHiCXA2112R-1 J CXA2112R-T6 BB
IC1103 RH-iX1531CEZZ J TC74HC4053AF AF
IC1104 VHiNJM2904V-1 J NJM2904V AF
IC1105 VHiLM318M//-1 J LM318M AK
IC1201 VHiCXA2112R-1 J CXA2112R-T6 BB
IC1202 VHiCXA2112R-1 J CXA2112R-T6 BB
IC1203 VHiAD8013AR-1 J AD8013AR-14 AV
IC1204 VHiNJM2902V-1 J NJM2902V AD
IC1301 VHiCXA2112R-1 J CXA2112R-T6 BB
IC1302 VHiCXA2112R-1 J CXA2112R-T6 BB
IC1305 VHiNJ7211U2-1 J NJU7211U20 AG
IC1401 VHiCXA2111R-1 J CXA2111R BB
IC1402 VHiTHC221AF-1 J TC74HC221AF AG
IC1403 VHiNJM2060V-1 J NJM2060V AF
IC1404 VHiM62352GP-1 J M62352GP AQ
IC1406 VHiHCT541AF-1 J TC74HCT541AF AG
IC1407 RH-iX1952CEZZ J 74F86SJ AD
IC1408 VHiHCT541AF-1 J TC74HCT541AF AG
IC1409 VHiPQ20VZ11-1 J PQ20VZ11 AH
IC1410 VHiPQ05TZ11-1 J PQ05TZ11 AH
IC1411 VHiTA8184F/-1 J TA8184F AN
IC1412 VHiM62352GP-1 J M62352GP AQ
IC1501 VHiAD8013AR-1 J AD8013AR-14 AV
IC1502 VHiNJM2902V-1 J NJM2902V AD
IC1503 VHiNJM431E/-1 J NJM431E-TE1 AF
IC1504 VHiM40C568H-1 J MD40C568HPFV-G AQ
IC1505 VHiM40C568H-1 J MD40C568HPFV-G AQ
IC1506 VHiM40C568H-1 J MD40C568HPFV-G AQ
IC1507 VHiPQ05TZ11-1 J PQ05TZ11 AH
IC1508 VHiT7WH241U-1 J TC7WH241FU AF
IC4201 VHiT7SET08U-1 J TC7SET08FU AE
IC4202 VHiTC4W53U/-1 J TC4W53FU AF
IC4203 VHiTC4W66U/-1 J TC4W66FU AF
IC4204 VHiNJM2060V-1 J NJM2060V AF
IC4206 VHiNJM2904V-1 J NJM2904V AF
IC4402 VHiTC4W53U/-1 J TC4W53FU AF
IC4403 VHiTC4W66U/-1 J TC4W66FU AF
IC4404 VHiNJM2060V-1 J NJM2060V AF
IC5003 VHiM62352GP-1 J M62352GP AQ
IC5004 VHiM62320FP-1 J M62320FP AK
IC5005 VHiM62320FP-1 J M62320FP AK
IC5006 VHiSNHC00T/-1 J SN74HC00PW AG
IC5008 RH-iX2963CEZZ J X24645S8T2 AX
IC5009 VHiSNHC08T/-1 J SN74HC08PW AG
IC5021 VHiPQ20VZ11-1 J PQ20VZ11 AH
IC5503 VHiPQ05SZ51-1 J PQ05SZ51 AG
IC5504 VHiPQ20VZ11-1 J PQ20VZ11 AH
IC5505 VHiPQ20VZ11-1 J PQ20VZ11 AH
IC5506 RH-iX2296CEZZ J TC7S66F AD
IC5507 VHiPQ20VZ11-1 J PQ20VZ11 AH

TRANSISTORS

Q1101 VS2SC2411KR-1 J 2SC2411KR AC
Q1102 VS2SA1036KR-1 J 2SA1036KR AC
Q1103 VS2SC2411KR-1 J 2SC2411KR AC
Q1104 VS2SA1036KR-1 J 2SA1036KR AC
Q1105 VS2SC2411KR-1 J 2SC2411KR AC
Q1106 VS2SA1036KR-1 J 2SA1036KR AC
Q1107 VS2SC2411KR-1 J 2SC2411KR AC
Q1108 VS2SA1036KR-1 J 2SA1036KR AC
Q1201 VS2SC2411KR-1 J 2SC2411KR AC
Q1202 VS2SA1036KR-1 J 2SA1036KR AC
Q1203 VS2SC2411KR-1 J 2SC2411KR AC
Q1204 VS2SA1036KR-1 J 2SA1036KR AC
Q1205 VS2SC2411KR-1 J 2SC2411KR AC
Q1206 VS2SA1036KR-1 J 2SA1036KR AC
Q1207 VS2SC2411KR-1 J 2SC2411KR AC
Q1208 VS2SA1036KR-1 J 2SA1036KR AC
Q1301 VS2SC2411KR-1 J 2SC2411KR AC

126

XG-NV5XB

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

DUNTK9839DE05

OUTPUT UNIT (Continued)

Q1302 VS2SA1036KR-1 J 2SA1036KR AC
Q1303 VS2SC2411KR-1 J 2SC2411KR AC
Q1304 VS2SA1036KR-1 J 2SA1036KR AC
Q1305 VS2SC2411KR-1 J 2SC2411KR AC
Q1306 VS2SA1036KR-1 J 2SA1036KR AC
Q1307 VS2SC2411KR-1 J 2SC2411KR AC
Q1308 VS2SA1036KR-1 J 2SA1036KR AC
Q1401 VS2SC2735//-1 J 2SC2735 AB
Q1402 VS2SC2735//-1 J 2SC2735 AB
Q1403 VS2SC2735//-1 J 2SC2735 AB
Q1501 VS2SC2735//-1 J 2SC2735 AB
Q1502 VS2SC2735//-1 J 2SC2735 AB
Q1503 VS2SC2735//-1 J 2SC2735 AB
Q1504 VS2SC2412KQ-1 J 2SC2412KQ AA
Q1505 VS2SA1037KQ-1 J 2SA1037KQ AA
Q1506 VS2SC2412KQ-1 J 2SC2412KQ AA
Q1507 VS2SC2412KQ-1 J 2SC2412KQ AA
Q1508 VS2SC2412KQ-1 J 2SC2412KQ AA
Q1510 VS2PD601AR/-1 J 2PD601AR AB
Q1511 VS2PB709AR/-1 J 2PB709AR AB
Q1512 VS2SD1664R/-1 J 2SD1664R AC
Q1601 VS2PD601AR/-1 J 2PD601AR AB
Q1602 VS2PD601AR/-1 J 2PD601AR AB
Q1603 VS2PD601AR/-1 J 2PD601AR AB
Q1604 VS2PD601AR/-1 J 2PD601AR AB
Q1605 VSDTC144EU/-1 J DTC144EU AB
Q1606 VSDTC144EU/-1 J DTC144EU AB
Q1607 VSDTC144EU/-1 J DTC144EU AB
Q1608 VSDTC144EU/-1 J DTC144EU AB
Q1609 VSDTC144EU/-1 J DTC144EU AB
Q1610 VSDTC144EU/-1 J DTC144EU AB
Q1611 VSDTC144EU/-1 J DTC144EU AB
Q1612 VSDTC144EU/-1 J DTC144EU AB
Q1613 VSDTC144EU/-1 J DTC144EU AB
Q1614 VSDTC144EU/-1 J DTC144EU AB
Q1615 VSDTC144EU/-1 J DTC144EU AB
Q1616 VSDTC144EU/-1 J DTC144EU AB
Q1617 VSDTC144EU/-1 J DTC144EU AB
Q1618 VSDTC144EU/-1 J DTC144EU AB
Q4204 VS2PD601AR/-1 J 2PD601AR AB
Q4205 VS2PD601AR/-1 J 2PD601AR AB
Q4207 VS2PD601AR/-1 J 2PD601AR AB
Q4208 VS2PD601AR/-1 J 2PD601AR AB
Q4401 VS2SA1037KQ-1 J 2SA1037KQ AA
Q4402 VS2SC2412KQ-1 J 2SC2412KQ AA
Q4403 VS2SC2412KQ-1 J 2SC2412KQ AA
Q4406 VS2SC2412KQ-1 J 2SC2412KQ AA
Q5002 VS2PD601AR/-1 J 2PD601AR AB
Q5003 VS2PD601AR/-1 J 2PD601AR AB
Q5004 VS2PD601AR/-1 J 2PD601AR AB
Q5005 VS2PD601AR/-1 J 2PD601AR AB
Q5006 VS2PB709AR/-1 J 2PB709AR AB
Q5007 VS2PD601AR/-1 J 2PD601AR AB
Q5501 VS2SD1664R/-1 J 2SD1664R AC
Q5502 VS2SD1664R/-1 J 2SD1664R AC
Q5514 VS2PD601AR/-1 J 2PD601AR AB
Q5516 VS2PD601AR/-1 J 2PD601AR AB
Q5518 VS2PD601AR/-1 J 2PD601AR AB
Q5526 VSDTC114EU/-1 J DTC114EU AB
Q5534 VSDTC114EU/-1 J DTC114EU AB
Q5536 VS2PD601AR/-1 J 2PD601AR AB

DIODES

D1003 VHDDAN202K/-1 J Diode DAN202K AB
D1401 VHDDAN202K/-1 J Diode DAN202K AB
D1402 VHDDAN202K/-1 J Diode DAN202K AB
D1501 VHDDAN202K/-1 J Diode DAN202K AB
D1502 VHDDAN202K/-1 J Diode DAN202K AB
D5001 VHDHRW0702A-1 J Diode HRW0702A AE
D5002 VHDHRW0702A-1 J Diode HRW0702A AE
D5003 VHDHRW0702A-1 J Diode HRW0702A AE
D5004 VHDHRW0702A-1 J Diode HRW0702A AE

D5005 VHDMA153///-1 J Diode MA153// AB
D5006 VHDMA153///-1 J Diode MA153// AB
D5007 VHDMA153///-1 J Diode MA153// AB
D5008 VHDMA153///-1 J Diode MA153// AB
D5009 VHDHRW0702A-1 J Diode HRW0702A AE
D5010 VHDHRW0702A-1 J Diode HRW0702A AE
D5011 VHDHRW0702A-1 J Diode HRW0702A AE
D5012 VHDHRW0702A-1 J Diode HRW0702A AE
D5013 VHDMA153///-1 J Diode MA153// AB
D5014 VHDMA153///-1 J Diode MA153// AB
D5015 VHDMA153///-1 J Diode MA153// AB
D5016 VHDMA153///-1 J Diode MA153// AB
D5017 VHDHRW0702A-1 J Diode HRW0702A AE
D5018 VHDMA153///-1 J Diode MA153// AB
D5023 VHDDAN202K/-1 J Diode DAN202K AB
D5024 RH-EX0858CEZZ J Zener Diode AC
D5503 VHDDAN202K/-1 J Diode DAN202K AB
D5504 VHDDAN202K/-1 J Diode DAN202K AB
D5505 VHDDAN202K/-1 J Diode DAN202K AB
D5513 VHDDAN202K/-1 J Diode DAN202K AB
D5514 RH-EX0228CEZZ J Zener Diode AB
D5520 VHDDAN202K/-1 J Diode DAN202K AB

COILS

L1101 VP-1M100J1R6N J Peaking 10µH AC
L1201 VP-1M100J1R6N J Peaking 10µH AC
L1301 VP-1M100J1R6N J Peaking 10µH AC

CONTROLS

R1649 RVR-M4565CEZZ J 470k (B) AC
R1652 RVR-M7906TAZZ J 68k (B) AC
R4215 RVR-M7904TAZZ J 33k (B) AC
R4415 RVR-M7904TAZZ J 33k (B) AC

CAPACITORS

[MLFT

···
C1010 VCEAPF1EW336M J 33 25V Electrolytic AB
C1013 VCEAPF1CW107M J 100 16V Electrolytic AD
C1038 VCEAPF1CW107M J 100 16V Electrolytic AD
C1039 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1040 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1041 VCEAPF1CW226M J 22 16V Electrolytic AB
C1101 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1102 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C1103 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1104 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1105 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1106 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1107 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C1108 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1109 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1110 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1111 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C1112 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1113 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C1114 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C1115 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1116 VCCCCY1HH5R0C J 5.0p 50V Ceramic AA
C1117 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1118 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1119 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1120 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1121 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1122 VCKYCY1HB103K J 0.01 50V Ceramic AA
C1125 VCKYCY1HB222K J 2200p 50V Ceramic AA
C1126 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C1127 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1128 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1201 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1202 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C1203 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1204 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1205 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1206 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1207 VCKYCY1EF104Z J 0.1 25V Ceramic AA

Multi Layer Film Tip]

127

XG-NV5XB

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

DUNTK9839DE05

OUTPUT UNIT (Continued)

C1208 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1209 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1210 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1211 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C1212 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1213 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C1214 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C1215 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1216 VCCCCY1HH5R0C J 5.0p 50V Ceramic AA
C1217 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1219 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1225 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C1226 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C1227 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1228 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1301 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1302 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C1303 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1304 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1305 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1306 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1307 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C1308 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1309 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1310 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1311 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C1312 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1313 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C1314 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C1315 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1316 VCCCCY1HH5R0C J 5.0p 50V Ceramic AA
C1325 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C1326 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C1327 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1328 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1340 VCKYD41HB471K J 470p 50V Ceramic AA
C1401 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1402 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1403 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1404 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1405 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1406 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1407 VCCCCY1HH100D J 10p 50V Ceramic AA
C1408 VCCCCY1HH100D J 10p 50V Ceramic AA
C1409 VCCCCY1HH100D J 10p 50V Ceramic AA
C1410 VCCCCY1HH100D J 10p 50V Ceramic AA
C1411 VCCCCY1HH100D J 10p 50V Ceramic AA
C1412 VCCCCY1HH100D J 10p 50V Ceramic AA
C1413 VCCCCY1HH100D J 10p 50V Ceramic AA
C1414 VCCCCY1HH100D J 10p 50V Ceramic AA
C1415 VCCCCY1HH100D J 10p 50V Ceramic AA
C1420 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1421 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1422 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1423 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1424 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1425 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1426 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1427 VCCCCY1HH101J J 100p 50V Ceramic AA
C1429 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1430 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1432 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1433 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C1434 VCEAPF1EW226M J 22 25V Electrolytic AB
C1435 VCEAPF1EW226M J 22 25V Electrolytic AB
C1436 VCEAPF1CW106M J 10 16V Electrolytic AB
C1437 VCEAPF0JW107M J 100 6.3V Electrolytic AC
C1438 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1451 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1453 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1460 VCKYCY1HB102K J 1000p 50V Ceramic AA
C1461 VCEAPF1CW476M J 47 16V Electrolytic AC

C1462 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1463 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1464 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1465 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1466 VCKYTV1CF105Z J 1.0 16V Ceramic AB
C1467 VCKYTV1CF105Z J 1.0 16V Ceramic AB
C1468 VCFRED1HM822J J 8200p 50V MLFT AD
C1469 VCFYEC1CM334J J 0.33 16V MLFT AE
C1470 VCEAPF1CW106M J 10 16V Electrolytic AB
C1471 VCKYCY1CF154Z J 0.15 16V Ceramic AB
C1472 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1473 VCE9PF1CW106M 0 10 16V Electr.(N.P) AC
C1474 VCEAPF1CW106M J 10 16V Electrolytic AB
C1475 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1476 VCEAPF1CW107M J 100 16V Electrolytic AD
C1477 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1478 VCEAPF1CW107M J 100 16V Electrolytic AD
C1479 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1480 VCEAPF1CW107M J 100 16V Electrolytic AD
C1481 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1482 VCEAPF1CW107M J 100 16V Electrolytic AD
C1483 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1484 VCEAPF1CW106M J 10 16V Electrolytic AB
C1501 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1502 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1503 VCKYCY1HB103K J 0.01 50V Ceramic AA
C1504 VCKYCY1HB103K J 0.01 50V Ceramic AA
C1505 VCKYCY1HB103K J 0.01 50V Ceramic AA
C1506 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1507 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1508 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1509 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1510 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1511 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1512 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1514 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1515 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1516 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1517 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1518 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1519 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1520 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1522 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1523 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1524 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1525 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1526 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1527 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1528 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1530 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1531 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1532 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1533 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1534 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1535 RC-KZ0416CEZZ J 10 25V Ceramic AE
C1540 VCEAPF1CW106M J 10 16V Electrolytic AB
C1541 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C1542 VCEAPF0JW107M J 100 6.3V Electrolytic AC
C1543 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C4201 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C4203 VCKYCY1HB103K J 0.01 50V Ceramic AA
C4204 VCKYCY1HB103K J 0.01 50V Ceramic AA
C4205 RC-KZ0416CEZZ J 10 25V Ceramic AE
C4206 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C4210 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C4213 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C4214 VCCCCY1EH102J J 1000p 25V Ceramic AB
C4215 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C4216 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C4217 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C4218 RC-KZ0416CEZZ J 10 25V Ceramic AE
C4220 VCCCCY1HH331J J 330p 50V Ceramic AA
C4221 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C4222 RC-KZ0416CEZZ J 10 25V Ceramic AE
C4402 VCEAPH1CW106M J 10 16V Electrolytic AB
C4410 VCKYCY1EF104Z J 0.1 25V Ceramic AA

128

XG-NV5XB

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

DUNTK9839DE05

OUTPUT UNIT (Continued)

C4413 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C4414 VCCCCY1EH102J J 1000p 25V Ceramic AB
C4415 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C4416 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C4417 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C4418 VCEAPH1EW475M J 4.7 25V Electrolytic AB
C4419 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C4421 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C4422 VCEAPH1CW106M J 10 16V Electrolytic AB
C5001 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C5007 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C5012 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C5015 VCCCCY1HH101J J 100p 50V Ceramic AA
C5016 VCCCCY1HH101J J 100p 50V Ceramic AA
C5017 VCCCCY1HH101J J 100p 50V Ceramic AA
C5033 VCEAPF0JW476M J 47 6.3V Electrolytic AB
C5041 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C5045 VCEAPF0JW107M J 100 6.3V Electrolytic AC
C5046 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C5056 VCEAPF0JW476M J 47 6.3V Electrolytic AB
C5057 VCKYCY1HB103K J 0.01 50V Ceramic AA
C5060 VCEAPF1HW105M J 1.0 50V Electrolytic AB
C5063 VCEAPF1CW107M J 100 16V Electrolytic AD
C5064 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C5065 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C5164 VCCCCY1HH221J J 220p 50V Ceramic AA
C5165 VCKYCY1HB102K J 1000p 50V Ceramic AA
C5167 VCKYCY1HB102K J 1000p 50V Ceramic AA
C5170 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C5171 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C5174 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C5507 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C5508 VCEAPF1CW476M J 47 16V Electrolytic AC
C5509 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C5510 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C5511 VCEAPF1EW336M J 33 25V Electrolytic AB
C5512 VCEAPF1CW107M J 100 16V Electrolytic AD
C5513 VCEAPF0JW107M J 100 6.3V Electrolytic AC
C5514 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C5515 VCEAPF1CW107M J 100 16V Electrolytic AD
C5516 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C5525 VCKYTV1EF104Z J 0.1 25V Ceramic AB
C5534 VCEAPF1CW226M J 22 16V Electrolytic AB
C5535 VCEAPF1CW226M J 22 16V Electrolytic AB
C5551 VCKYCY1HB103K J 0.01 50V Ceramic AA
C5553 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C5554 VCKYCY1CF104Z J 0.1 16V Ceramic AA
C5555 VCKYCY1HB103K J 0.01 50V Ceramic AA
C5556 VCKYCY1HB103K J 0.01 50V Ceramic AA
C5562 VCKYCY1HB103K J 0.01 50V Ceramic AA
C5564 VCEAPF1CW226M J 22 16V Electrolytic AB
C5565 VCEAPF1EW336M J 33 25V Electrolytic AB
C5566 VCEAPF1CW107M J 100 16V Electrolytic AD
C5567 VCKYCY1EF104Z J 0.1 25V Ceramic AA

RESISTORS

R1003 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1015 VRS-TX2HF000J J 0 1/2W Metal Oxide AA
R1016 VRS-TX2HF000J J 0 1/2W Metal Oxide AA
R1018 QFS-L5015CEZZ J Fuse Resistor AD
R1033 VRS-CY1JF473J J 47k 1/16W Metal Oxide AA
R1049 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1050 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1051 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1052 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1053 VRS-CY1JF820J J 82 1/16W Metal Oxide AA
R1054 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1055 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1056 VRS-CY1JF271J J 270 1/16W Metal Oxide AA
R1057 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1059 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1061 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA

R1062 VRS-CY1JF333J J 33k 1/16W Metal Oxide AA
R1065 VRS-CY1JF153J J 15k 1/16W Metal Oxide AA
R1066 VRS-CY1JF682J J 6.8k 1/16W Metal Oxide AA
R1067 VRS-CY1JF472J J 4.7k 1/16W Metal Oxide AA
R1068 VRS-CY1JF202J J 2.0k 1/16W Metal Oxide AA
R1069 VRS-CY1JF751J J 750 1/16W Metal Oxide AA
R1070 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1071 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1072 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1073 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1074 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1075 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1076 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1077 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1078 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1079 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1080 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1081 VRS-CY1JF203J J 20k 1/16W Metal Oxide AA
R1082 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1083 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1084 VRS-CY1JF203J J 20k 1/16W Metal Oxide AA
R1085 VRS-CY1JF153J J 15k 1/16W Metal Oxide AA
R1086 VRS-CY1JF682J J 6.8k 1/16W Metal Oxide AA
R1087 VRS-CY1JF472J J 4.7k 1/16W Metal Oxide AA
R1088 VRS-CY1JF472J J 4.7k 1/16W Metal Oxide AA
R1089 VRS-CY1JF682J J 6.8k 1/16W Metal Oxide AA
R1090 VRS-CY1JF153J J 15k 1/16W Metal Oxide AA
R1093 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1094 VRS-CY1JF203J J 20k 1/16W Metal Oxide AA
R1095 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1096 VRS-CY1JF391J J 390 1/16W Metal Oxide AA
R1102 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1103 VRS-CY1JF273F J 27k 1/16W Metal Oxide AA
R1104 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1105 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1106 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1107 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1108 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1109 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1110 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1111 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1112 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1113 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1114 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1115 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1116 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1117 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1118 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1120 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1122 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1123 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1124 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1125 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1126 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1127 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1128 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1129 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1130 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1131 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1132 VRS-CY1JF560J J 56 1/16W Metal Oxide AA
R1133 VRS-CY1JF560J J 56 1/16W Metal Oxide AA
R1134 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1135 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1136 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1137 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1138 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1139 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1140 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1141 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1142 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1143 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1144 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1145 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1146 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1147 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1148 VRS-CY1JF000J J 0 1/16W Metal Oxide AA

129

XG-NV5XB

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

DUNTK9839DE05

OUTPUT UNIT (Continued)

R1149 VRS-CY1JF273F J 27k 1/16W Metal Oxide AA
R1150 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1153 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1154 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1155 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1156 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1157 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1158 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1159 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1160 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1161 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1162 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1164 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1165 VRS-CY1JF222J J 2.2k 1/16W Metal Oxide AA
R1166 VRS-CY1JF222J J 2.2k 1/16W Metal Oxide AA
R1167 VRS-CY1JF3R3J J 3.3 1/16W Metal Oxide AA
R1168 VRS-CY1JF3R3J J 3.3 1/16W Metal Oxide AA
R1169 VRS-CY1JF3R3J J 3.3 1/16W Metal Oxide AA
R1171 VRS-CY1JF222J J 2.2k 1/16W Metal Oxide AA
R1172 VRS-CY1JF222J J 2.2k 1/16W Metal Oxide AA
R1173 VRS-CY1JF3R3J J 3.3 1/16W Metal Oxide AA
R1174 VRS-CY1JF3R3J J 3.3 1/16W Metal Oxide AA
R1175 VRS-CY1JF3R3J J 3.3 1/16W Metal Oxide AA
R1176 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1178 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1179 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1180 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1184 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1185 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1186 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1187 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1188 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1189 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1190 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1191 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1192 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1193 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1194 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1195 VRS-CY1JF2R2J J 2.2 1/16W Metal Oxide AA
R1196 VRS-CY1JF2R2J J 2.2 1/16W Metal Oxide AA
R1201 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1202 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1203 VRS-CY1JF273F J 27k 1/16W Metal Oxide AA
R1204 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1205 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1206 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1207 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1208 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1209 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1210 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1211 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1212 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1213 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1214 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1215 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1216 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1217 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1218 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1220 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1222 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1223 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1224 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1225 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1226 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1227 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1228 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1229 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1230 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1231 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1234 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1235 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1236 VRS-CY1JF000J J 0 1/16W Metal Oxide AA

R1237 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1238 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1239 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1240 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1241 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1242 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1243 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1244 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1245 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1246 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1247 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1248 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1249 VRS-CY1JF273F J 27k 1/16W Metal Oxide AA
R1250 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1253 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1254 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1255 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1256 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1257 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1258 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1259 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1260 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1261 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1262 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1264 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1265 VRS-CY1JF222J J 2.2k 1/16W Metal Oxide AA
R1266 VRS-CY1JF222J J 2.2k 1/16W Metal Oxide AA
R1267 VRS-CY1JF3R3J J 3.3 1/16W Metal Oxide AA
R1268 VRS-CY1JF3R3J J 3.3 1/16W Metal Oxide AA
R1269 VRS-CY1JF3R3J J 3.3 1/16W Metal Oxide AA
R1271 VRS-CY1JF222J J 2.2k 1/16W Metal Oxide AA
R1272 VRS-CY1JF222J J 2.2k 1/16W Metal Oxide AA
R1273 VRS-CY1JF3R3J J 3.3 1/16W Metal Oxide AA
R1274 VRS-CY1JF3R3J J 3.3 1/16W Metal Oxide AA
R1275 VRS-CY1JF3R3J J 3.3 1/16W Metal Oxide AA
R1276 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1278 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1279 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1280 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1284 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1285 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1286 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1287 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1288 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1289 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1290 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1291 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1292 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1294 VRS-CY1JF333J J 33k 1/16W Metal Oxide AA
R1301 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1302 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1303 VRS-CY1JF273F J 27k 1/16W Metal Oxide AA
R1304 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1305 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1306 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1307 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1308 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1309 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1310 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1311 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1312 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1313 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1314 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1315 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1316 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1317 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1318 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1320 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1322 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1323 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1324 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1325 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1326 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1327 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1328 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1329 VRS-CY1JF000J J 0 1/16W Metal Oxide AA

130

XG-NV5XB

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

DUNTK9839DE05

OUTPUT UNIT (Continued)

R1330 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1331 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1334 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1335 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1336 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1337 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1338 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1339 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1340 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1341 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1342 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1343 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1344 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1345 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1346 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1347 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1348 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1349 VRS-CY1JF273F J 27k 1/16W Metal Oxide AA
R1350 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1353 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1354 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1355 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1356 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1357 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1358 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1359 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1360 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1361 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1362 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1364 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1365 VRS-CY1JF222J J 2.2k 1/16W Metal Oxide AA
R1366 VRS-CY1JF222J J 2.2k 1/16W Metal Oxide AA
R1367 VRS-CY1JF3R3J J 3.3 1/16W Metal Oxide AA
R1368 VRS-CY1JF3R3J J 3.3 1/16W Metal Oxide AA
R1369 VRS-CY1JF3R3J J 3.3 1/16W Metal Oxide AA
R1371 VRS-CY1JF222J J 2.2k 1/16W Metal Oxide AA
R1372 VRS-CY1JF222J J 2.2k 1/16W Metal Oxide AA
R1373 VRS-CY1JF3R3J J 3.3 1/16W Metal Oxide AA
R1374 VRS-CY1JF3R3J J 3.3 1/16W Metal Oxide AA
R1375 VRS-CY1JF3R3J J 3.3 1/16W Metal Oxide AA
R1376 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1378 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1379 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1380 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1384 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1385 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1386 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1387 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1388 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1389 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1390 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1391 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1392 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1393 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1394 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1395 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1396 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1401 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1402 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1403 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1404 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1405 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1406 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1407 VRS-CY1JF181J J 180 1/16W Metal Oxide AA
R1408 VRS-CY1JF181J J 180 1/16W Metal Oxide AA
R1409 VRS-CY1JF181J J 180 1/16W Metal Oxide AA
R1410 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1411 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1412 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1413 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1414 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R1415 VRS-CY1JF101J J 100 1/16W Metal Oxide AA

R1416 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1417 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1418 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1419 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1420 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1421 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1422 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1423 VRS-CB1JF101J J 100 1/16W Metal Oxide AA
R1424 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1428 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1429 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1430 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1431 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1432 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1433 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1434 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1435 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1436 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1437 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1438 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1439 VRS-CY1JF100J J 10 1/16W Metal Oxide AA
R1440 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1441 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1442 VRS-CY1JF682J J 6.8k 1/16W Metal Oxide AA
R1443 VRS-CY1JF682J J 6.8k 1/16W Metal Oxide AA
R1444 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1447 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1448 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1449 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1450 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1451 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1452 VRS-CY1JF222J J 2.2k 1/16W Metal Oxide AA
R1453 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1454 VRS-CY1JF202J J 2.0k 1/16W Metal Oxide AA
R1455 VRS-CY1JF302J J 3.0k 1/16W Metal Oxide AA
R1456 VRS-CY1JF562J J 5.6k 1/16W Metal Oxide AA
R1457 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1458 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1459 VRN-CY1JF392D J 3.9k 1/16W Metal Film AA
R1460 VRN-CY1JF392D J 3.9k 1/16W Metal Film AA
R1461 VRS-CY1JF2R2J J 2.2 1/16W Metal Oxide AA
R1462 VRN-CY1JF392D J 3.9k 1/16W Metal Film AA
R1464 VRN-CY1JF392D J 3.9k 1/16W Metal Film AA
R1465 VRS-CY1JF2R2J J 2.2 1/16W Metal Oxide AA
R1466 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1467 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1468 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1469 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1470 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1471 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1472 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1473 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1474 VRS-CY1JF123F J 12k 1/16W Metal Oxide AA
R1475 VRS-CY1JF102F J 1.0k 1/16W Metal Oxide AA
R1476 VRS-CY1JF510F J 51 1/16W Metal Oxide AA
R1477 VRS-TX2HF000J J 0 1/2W Metal Oxide AA
R1478 VRS-CY1JF104J J 100k 1/16W Metal Oxide AA
R1479 VRS-CY1JF104J J 100k 1/16W Metal Oxide AA
R1480 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1483 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1485 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1486 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1487 VRS-CY1JF472J J 4.7k 1/16W Metal Oxide AA
R1488 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1489 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1490 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1491 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1492 VRS-CY1JF222J J 2.2k 1/16W Metal Oxide AA
R1493 VRS-TX2HF5R6J J 5.6 1/2W Metal Oxide AA
R1494 VRS-CY1JF104J J 100k 1/16W Metal Oxide AA
R1495 VRS-CY1JF104J J 100k 1/16W Metal Oxide AA
R1496 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1497 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1498 VRS-CY1JF473J J 47k 1/16W Metal Oxide AA
R1499 VRS-TV1JD000J J 0 1/16W Metal Oxide AA
R1501 VRN-CY1JF102D J 1.0k 1/16W Metal Film AB

131

XG-NV5XB

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

DUNTK9839DE05

OUTPUT UNIT (Continued)

R1502 VRN-CY1JF102D J 1.0k 1/16W Metal Film AB
R1503 VRS-CY1JF221J J 220 1/16W Metal Oxide AA
R1504 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1505 VRN-CY1JF102D J 1.0k 1/16W Metal Film AB
R1506 VRS-CY1JF221J J 220 1/16W Metal Oxide AA
R1507 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1508 VRN-CY1JF102D J 1.0k 1/16W Metal Film AB
R1509 VRS-CY1JF221J J 220 1/16W Metal Oxide AA
R1510 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R1511 VRN-CY1JF102D J 1.0k 1/16W Metal Film AB
R1512 VRS-CY1JF153J J 15k 1/16W Metal Oxide AA
R1513 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1515 VRS-TV1JD000J J 0 1/16W Metal Oxide AA
R1517 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1518 VRS-CY1JF272J J 2.7k 1/16W Metal Oxide AA
R1529 VRS-CY1JF512F J 5.1k 1/16W Metal Oxide AA
R1530 VRS-CY1JF102F J 1.0k 1/16W Metal Oxide AA
R1531 VRS-CY1JF471J J 470 1/16W Metal Oxide AA
R1532 VRS-CY1JF202F J 2.0k 1/16W Metal Oxide AA
R1533 VRS-CY1JF102F J 1.0k 1/16W Metal Oxide AA
R1534 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1535 VRS-CY1JF680J J 68 1/16W Metal Oxide AA
R1536 VRS-CY1JF470J J 47 1/16W Metal Oxide AA
R1537 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1538 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1539 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1540 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1541 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1542 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1543 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1544 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1545 VRS-CY1JF680J J 68 1/16W Metal Oxide AA
R1546 VRS-CY1JF470J J 47 1/16W Metal Oxide AA
R1547 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1548 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1549 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1550 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1551 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1552 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1553 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1554 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1555 VRS-CY1JF680J J 68 1/16W Metal Oxide AA
R1556 VRS-CY1JF470J J 47 1/16W Metal Oxide AA
R1557 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1558 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1559 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1560 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1561 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1562 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1563 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1564 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1565 VRS-CY1JF470J J 47 1/16W Metal Oxide AA
R1566 VRS-CY1JF470J J 47 1/16W Metal Oxide AA
R1567 VRS-CY1JF470J J 47 1/16W Metal Oxide AA
R1568 VRN-CY1JF102D J 1.0k 1/16W Metal Film AB
R1575 VRN-CY1JF821D J 820 1/16W Metal Film AB
R1576 VRN-CY1JF821D J 820 1/16W Metal Film AB
R1577 VRN-CY1JF821D J 820 1/16W Metal Film AB
R1580 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1581 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1582 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1583 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1584 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1585 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1586 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1590 VRN-CY1JF102D J 1.0k 1/16W Metal Film AB
R1591 VRN-CY1JF102D J 1.0k 1/16W Metal Film AB
R1592 VRN-CY1JF102D J 1.0k 1/16W Metal Film AB
R1606 VRS-CY1JF392J J 3.9k 1/16W Metal Oxide AA
R1607 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1608 VRS-CY1JF392J J 3.9k 1/16W Metal Oxide AA
R1609 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA

R1610 VRS-CY1JF392J J 3.9k 1/16W Metal Oxide AA
R1611 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1612 VRS-CY1JF392J J 3.9k 1/16W Metal Oxide AA
R1613 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1626 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1627 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1628 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1629 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1630 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1631 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1632 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1633 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1634 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1635 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1636 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1637 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R1638 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1639 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R1648 VRS-TV1JD000J J 0 1/16W Metal Oxide AA
R1650 VRS-CY1JF124J J 120k 1/16W Metal Oxide AA
R1651 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R1653 VRS-CY1JF683J J 68k 1/16W Metal Oxide AA
R1654 VRS-CY1JF273J J 27k 1/16W Metal Oxide AA
R1657 VRS-CY1JF563J J 56k 1/16W Metal Oxide AA
R1658 VRS-CY1JF563J J 56k 1/16W Metal Oxide AA
R1659 VRS-CY1JF563J J 56k 1/16W Metal Oxide AA
R1660 VRS-CY1JF563J J 56k 1/16W Metal Oxide AA
R4210 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R4211 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R4212 VRS-CY1JF472J J 4.7k 1/16W Metal Oxide AA
R4213 VRS-CY1JF333J J 33k 1/16W Metal Oxide AA
R4214 VRS-CY1JF682J J 6.8k 1/16W Metal Oxide AA
R4217 VRS-CY1JF153J J 15k 1/16W Metal Oxide AA
R4218 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R4223 VRS-CY1JF151J J 150 1/16W Metal Oxide AA
R4224 VRS-CY1JF562F J 5.6k 1/16W Metal Oxide AA
R4225 VRS-CY1JF272F J 2.7k 1/16W Metal Oxide AA
R4226 VRS-CY1JF822F J 8.2k 1/16W Metal Oxide AA
R4227 VRS-CY1JF472F J 4.7k 1/16W Metal Oxide AA
R4228 VRS-CY1JF393F J 39k 1/16W Metal Oxide AA
R4229 VRS-CY1JF392F J 3.9k 1/16W Metal Oxide AA
R4230 VRS-CY1JF223J J 22k 1/16W Metal Oxide AA
R4231 VRS-CY1JF153J J 15k 1/16W Metal Oxide AA
R4232 VRS-CY1JF223J J 22k 1/16W Metal Oxide AA
R4233 VRS-CY1JF153J J 15k 1/16W Metal Oxide AA
R4234 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R4237 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R4239 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R4401 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R4405 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R4406 VRS-CY1JF223J J 22k 1/16W Metal Oxide AA
R4407 VRS-CY1JF153J J 15k 1/16W Metal Oxide AA
R4408 VRS-CY1JF223J J 22k 1/16W Metal Oxide AA
R4409 VRS-CY1JF153J J 15k 1/16W Metal Oxide AA
R4413 VRS-CY1JF333J J 33k 1/16W Metal Oxide AA
R4414 VRS-CY1JF104J J 100k 1/16W Metal Oxide AA
R4418 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide AA
R4419 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R4420 VRS-CY1JF151J J 150 1/16W Metal Oxide AA
R4421 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R4422 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R4423 VRS-CY1JF151J J 150 1/16W Metal Oxide AA
R4498 VRS-CY1JF000J J 0 1/16W Metal Oxide AA
R5003 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R5004 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide AA
R5005 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R5006 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R5007 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R5008 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R5010 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R5011 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R5012 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R5013 VRS-CY1JF103J J 10k 1/16W Metal Oxide AA
R5016 VRS-CY1JF101J J 100 1/16W Metal Oxide AA
R5017 VRS-TX2HF3R9J J 3.9 1/2W Metal Oxide AB
R5018 VRS-TX2HF3R9J J 3.9 1/2W Metal Oxide AB

132