Sharp MX-M182, M182D, MX-M202D, M232D Service Manual

Download

(With optional

SPF/RSPF installed)

MX-M182/M182D

CODE : 00ZMXM182/S1E

DIGITAL MULTIFUNCTIONAL SYSTEM

(With optional

SPF/RSPF installed)

MX-M182 MX-M182D MX-M202D

MODEL

MX-M202D/M232D

CONTENTS

[ 1 ] GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1

[ 2 ] CONFIGURATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1

[ 3 ] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1

[ 4 ] CONSUMABLE PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1

[ 5 ] EXTERNAL VIEWS AND INTERNAL STRUCTURES . . . . . . . 5 - 1

[ 6 ] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1

[ 7 ] SIMULATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1

[ 8 ] TROUBLE CODE LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1

[ 9 ] MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1

[10] DISASSEMBLY AND ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . 10 - 1

[11] OPERATIONAL DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . 11 - 1

MX-M232D

[12] FLASH ROM VERSION UP PROCEDURE. . . . . . . . . . . . . . . 12 - 1

[13] IP ADDRESS SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 - 1

[14] ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 - 1

Parts marked with “ “ are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

This document has been published to be used

SHARP CORPORATION

for after sales service only. The contents are subject to change without notice.

Disconnect the AC cord before servicing the unit. LASER WAVE - LENGTH : 785 15mm

Pulse times : 10.34 s 0.1 s/7mm ; MX-M182, MX-M182D, MX-M202D

8.665 s 0.1 s/7mm ; MX-M232D

Out put power : Max. 0.3mW

CONTENTS

[1] GENERAL

1. Note for servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1

[2] CONFIGURATION

1. System Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1

[3] SPECIFICATIONS

1. Copy mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1

2. Print mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 4

3. Scanner mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 8

[4] CONSUMABLE PARTS

1. Supply system table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1

2. Environmental conditions . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 2

3. Production number identification . . . . . . . . . . . . . . . . . . . 4 - 3

[5] EXTERNAL VIEWS AND INTERNAL STRUCTURES

1. Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1

2. Internal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 2

3. Operation Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 3

4. Motor, solenoid, clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 4

5. Sensor, switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 5

6. PWB unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 6

7. Cross sectional view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 7

[6] ADJUSTMENTS

1. Adjustment item list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1

2. Copier adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1

[7] SIMULATIONS

1. Entering the simulation mode. . . . . . . . . . . . . . . . . . . . . . 7 - 1

2. Canceling the simulation mode. . . . . . . . . . . . . . . . . . . . . 7 - 1

3. List of simulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1

4. Contents of simulations . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 3

[8] TROUBLE CODE LIST

1. Trouble code list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1

2. Details of trouble codes . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1

3. Communication result code . . . . . . . . . . . . . . . . . . . . . . .8 - 6

[10] DISASSEMBLY AND ASSEMBLY

1. High voltage section/Duplex transport section . . . . . . . .10 - 1

2. Optical section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 2

3. Fusing section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 4

4. Paper exit section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 7

5. MCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 10

6. Optical frame unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 10

7. LSU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 10

8. Tray paper feed section/Paper transport section . . . . .10 - 11

9. Bypass tray section . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 12

10. Power section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 14

11. Developing section . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 15

12. Process section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 16

13. Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 17

[11] OPERATIONAL DESCRIPTIONS

1. Paper feed operation. . . . . . . . . . . . . . . . . . . . . . . . . . . .11 - 1

[12] FLASH ROM VERSION UP PROCEDURE

1. Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 1

2. Download procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 1

3. Version confirming procedure . . . . . . . . . . . . . . . . . . . . .12 - 3

4. Facsimile Data upload procedure . . . . . . . . . . . . . . . . . .12 - 4

5. Updating the MX-NB12 firmware. . . . . . . . . . . . . . . . . . .12 - 5

6. Installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 6

[13] IP ADDRESS SETTING

1. Setting the ip address of the machine by 

system settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 - 1

[14] ELECTRICAL SECTION

1. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 - 1

2. Actual wiring diagram . . . . . . . . . . . . . . . . . . . . . . . . . . .14 - 2

[9] MAINTENANCE

1. Maintenance table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1

2. Maintenance display system . . . . . . . . . . . . . . . . . . . . . . 9 - 2

3. Note for replacement of consumable parts . . . . . . . . . . . 9 - 2

[1] GENERAL

1. Note for servicing

Pictogram

The label ( ) in the fusing area of the machine indicates the following:

: Caution, risk of danger : Caution, hot surface

•poorly ventilated

A. Warning for servicing

•The fusing area is hot. Exercise care in this area when removing misfeed paper.

•Do not disassemble the laser unit. Do not insert a reflective material such as a screwdriver in the laser beam path. It may damage eyes by reflection of laser beams.



B. Cautions for servicing

•Do not switch the machine rapidly on and off. After turning the machine off, wait 10 to 15 seconds before turning it back on.

•Machine power must be turned off before installing any supplies.

•Place the machine on a firm, level surface.

•Do not install the machine in a humid or dusty location.

•When the machine is not used for a long time, for example, during prolonged holidays, turn the power switch off and remove the power cord from the outlet.

•When moving the machine, be sure to turn the power switch off and remove the power cord from the outlet.

•Do not cover the machine with a dust cover, cloth or plastic film while the power is on. Doing so may prevent heat dissipation, damaging the machine.

•Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser radiation exposure.

•The socket-outlet shall be installed near the machine and shall be easily accessible.

C. Note for installation place

Improper installation may damage the machine. Please note the following during initial installation and whenever the machine is moved.

Caution : If the machine is moved from a cool place to a warm place,

condensation may form inside the machine. Operation in this condition will cause poor copy quality and malfunctions. Leave the machine at room temperature for at least 2 hours before use.

Do not install your machine in areas that are:

•damp, humid, or very dusty

•exposed to direct sunlight

•subject to extreme temperature or humidity changes, e.g., near an air conditioner or heater.

The machine should be installed near an accessible power outlet for easy connection and disconnection. Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements. Also make certain the outlet is properly grounded.

Note : Connect the machine to a power outlet which is not used for other

electric appliances. If a lighting fixture is connected to the same outlet, the light may flicker.

Be sure to allow the required space around the machine for servicing and proper ventilation.

20 cm (8

)

MX-M182 GENERAL 1-1

20 cm

)

20 cm

)

D. Note for handling PWB and electronic parts

When handling the PWB and the electronic parts, be sure to observe the following precautions in order to prevent against damage by static electricity.

1) When in transit or storing, put the parts in an anti-static bag or an anti-static case and do not touch them with bare hands.

2) When and after removing the parts from an anti-static bag (case), use an earth band as shown below:

•Put an earth band to your arm, and connect it to the machine.

3) When repairing or replacing an electronic part, perform the procedure on an anti-static mat.

MX-M182 GENERAL 1-2

[2] CONFIGURATION

1. System Configurations

AR-RP10

(MX-M182D/M202D/M232D only)

MX-M182

AR-SP10

AR-VR7

(MX-M182 is standard.)

MX-M232D MX-M182D MX-M202D

MX-NB12

MX-FX13

MX-XB17

MX-PK10

PS3 EXPANSION KIT

AR-D36

MX-USX1

Sharpdesk 1 license kit

AR-D37

MX-USX5

Sharpdesk 5 license kit

MX-US10

Sharpdesk 10 license kit

MX-US50

Sharpdesk 50 license kit

MX-EB14

MX-TR10

MX-USA0

Sharpdesk 100 license kit

MX-M182 CONFIGURATION 2-1

Model

Option AR-RP10 Reversing single pass feeder (RSPF) AR-SP10 Single pass feeder (SPF) AR-D36 250-sheet paper feed unit AR-D37 2x250-sheet paper feed unit AR-VR7 DOCUMENT COVER MX-NB12 NETWORK EXPANSION KIT MX-FX13 FACSIMILE EXPANSION KIT MX-XB17 FACSIMILE MOUNTING KIT MX-TR10 JOB SEPARATOR MX-EB14 EXPANSION MEMORY BOARD MX-PK10 PS3 EXPANSION KIT MX-USX1 SHARPDESK 1 LICENSE KIT MX-USX5 SHARPDESK 5 LICENSE KIT MX-US10 SHARPDESK 10 LICENSE KIT MX-US50 SHARPDESK 50 LICENSE KIT MX-USA0 SHARPDESK 100 LICENSE KIT

STD: Standard

: Option installation enable *1 Standard for U.S.A *2 Not available for U.S.A *3 MX-NB12 or MX-XB17 is required. *4 MX-NB12 is required.

: Option installation disable

MX-M182 MX-M182D/M202D/M232D

X O*1 O O*2 O O O O

STD O*2

O O

O*3 O*3

O O O O O O

O*4 O*4

O O O O O O O O O O

MX-M182 CONFIGURATION 2-2

[3] SPECIFICATIONS

1. Copy mode

A. Type

Ty pe Desk-top Paper exit center tray / internal

B. Machine composition

MX-M182 MX-M182D MX-M202D 20-CPM multi function model MX-M232D 23-CPM multi function model

(1) Option

Machine Model

250-sheet paper feed unit AR-D36 MX-M182/M182D/M202D/

2x250-sheet paper feed unit AR-D37 MX-M182/M182D/M202D/

SPF AR-SP10 MX-M182/M182D/M202D/

RSPF*1 AR-RP10 MX-M182D/M202D/M232D Network expansion kit MX-NB12 MX-M182/M182D/M202D/

Document cover AR-VR7 MX-M182D/M202D/M232D Job separator MX-TR10 MX-M182/M182D/M202D/

PS3 Expantion kit MX-PK10 MX-M182/M182D/M202D/

Facsimile expantion kit MX-FX13 MX-M182/M182D/M202D/

Facsimile mounting kit MX-XB17 MX-M182/M182D/M202D/

Expantion memory board MX-EB14 MX-M182/M182D/M202D/

*1: Standard for North America and Latin America.

C. Copy speed

(1) Engine speed (ppm)

Paper size MX-M232D MX-M202D

A4/8.5" x 11" 23ppm 20ppm 18ppm A4R/8.5" x 11"R 15/16ppm 14/15ppm 14/15ppm A5/5.5"x8.5" 23ppm 20ppm 18ppm B5/16K 23ppm 20ppm 18ppm B5R/16KR 18/16ppm 16/15ppm 16/15ppm

8.5"x13" 13ppm 12ppm 12ppm B4/8.5"x14" 13ppm 12ppm 12ppm A3/11"x17"/8K 12/11/12ppm 11/10/11ppm 11/10/11ppm

18-CPM multi function model

M232D

MX-M182

MX-M182D

(4) Job efficiency

Copy mode MX-M232D MX-M202D

S to S 18cpm (78%) 18cpm (90%) 15cpm (83%) S to D 10cpm (43%) 10cpm (50%) 10cpm (56%) D to D 10cpm (43%) 10cpm (50%) 10cpm (56%)

S to S : A4/8.5" x 11" document 10 sheets, copy 5 sets S to D : A4/8.5" x 11" document 10 sheets, copy 5 sets D to D : A4/8.5" x 11" document 10 sheets (20 pages), copy 5 sets

Note :The temperature at the end portion of the heat roller may rise too

high, depending on the kind of paper to be used, when in continuous printing of small-size paper. To avoid this, when the thermistor at the end portion detects a higher temperature than the specified level, output is stopped temporarily. During temporary stop, Power Save Indicator lamp flashes in the same manner as warming up.



MX-M182

MX-M182D

(5) First copy time

Tr ay 18/20cpm machine 23cpm machine

1st tray 7.2 sec or less 5.9 sec or less

AE mode, A4/Letter, single surface copy with OC, in polygon ready state

D. Document

Max. document size A3, 11" x 17" Document reference position Upper left-hand corner Detection (Platen) Ye s

E. Paper feed

(1) Paper feed section details

Item 1st tray 2nd tray*1 Paper capacity 250 sheets 250 sheets 100 sheets Paper size detection No

Paper type setting No No No

Paper size changing method The paper guide is set by the user. Default paper size

when shipping Remaining paper quantity

detection

*1: 2-stage standard only for the MX-M202D/M232D

AB series A4 A4 Inch series

(Paper size is set with

the operasion panel.)

8 1/2" x11" 8 1/2" x11"

Only empty detection available

Bypass tray

(Heavy

paper setting

is enabled.)

(2) Engine performance when printing

Model 23cpm machine 20cpm machine 18cpm machine ROPM OFF 12ppm or more 12ppm or more 12ppm or more ROPM ON 23ppm 20ppm 18ppm

(3) Document replacement speed (Copy mode)

Copy mode MX-M232D MX-M202D

S to S 20cpm (87%) 20cpm (100%) 18cpm (100%)

S to S : A4/8.5" x 11" document 11 sheets, copy 1 set (Excluding the first copy)

MX-M182

MX-M182D

MX-M182 SPECIFICATIONS 3-1

(2) Feedable paper

Paper size 1st tray 2nd tray

A3 297x420 Ye s Yes Ye s B4 257x364 Ye s Yes Ye s A4 297x210 Ye s Yes Ye s A4-R 210x297 Ye s Ye s Ye s B5 257x182 Ye s Yes Ye s B5R 182x257 Ye s Ye s Ye s A5 210x148.5 Ye s N/A Ye s A5R 148.5x210 N/A N/A Ye s A6R 105x148.5 N/A N/A Ye s B6R 128.5x182 N/A N/A Ye s Ledger 11x17 in 279.4x431.8 Ye s Ye s Yes Legal 8.5x14in. 215.9x355.6 Ye s Ye s Ye s

8.5x13.4 *1 216x340 *1 *1 *1 *1 Foolscap 8.5x13 in 215.9x330.2 Ye s Ye s Yes Letter 11x8.5in 279.4x215.9 Ye s Ye s Ye s Letter-R 8.5x11in 215.9x279.4 Ye s Ye s Yes Executive-R 7.25x10.5in. 184.2x266.7 N/A N/A Ye s Invoice 8.5x5.5 in. 215.9x139.7 Ye s N/A Ye s Invoice-R 5.5x8.5 in 139.7x215.9 N/A N/A Ye s 8K 270x390 Ye s Ye s Ye s 16K 270x195 Ye s Ye s Ye s 16KR 195x270 Ye s Ye s Ye s COM10 104.8x241.3 N/A N/A Ye s

*1: Switches by SIM26-2. (Operation UI supports by 8.5x13 and exclusion.)

Bypass

tray

(3)Types of feedable paper

Types of paper 1st tray 2nd tray Bypass tray

Thin paper 56-59g/m

15-15.9lbs

Plain paper 60-90g/m

16-24lbs

Heavy paper 91-105g/m

16-24lbs

Heavy paper 106-128g/m

24.1-33.5lbs

Heavy paper 129-200g/m

33.6-53.2lbs

Heavy paper 201-256g/m

53.3-68lbs

Envelope 75-90g/m

20-24lbs Postcard N/A N/A Ye s OHP film N/A N/A Ye s Label sheet N/A N/A Ye s Tab paper 20 N/A N/A N/A

Ye s Ye s Ye s

N/A N/A Ye s

N/A N/A N/A

N/A N/A Ye s

(Multi paper feed enable)

(A4 or less)

(Multi paper feed enable)

(A4 or less)

(Only single paper feed)

H. Copy magnification ratio

Fixed magnification ratio

Zooming 25 ~ 400%

Independent zooming (vertical) Independent zooming (horizontal)

AB system: 400, 200, 141, 122, 115, 100, 86, 81, 70, 50, 25% Inch system: 400, 200, 141, 129, 121, 100, 95, 77, 64, 50, 25%

SPF/RSPF (50 ~ 200%) Available (25 ~ 400%) SPF/RSPF (50 ~ 200%) Available (25 ~ 400%) SPF/RSPF (50 ~ 200%)

I. Copy density

Density mode Auto / Text / Photo No. of manual

adjustment Resolution Writing: 600 x 600dpi

Gradation Reading: 256 gradations

5 steps (Text / Photo)

Reading: 400 (main) x 600 (sub) (PHOTO mode)

400 (main) x 600 (sub) (AUTO exposure  mode) 400 (main) x 600 (sub) dpi (TEXT mode)

Writing: Binary

J. Void width

Void area Lead edge 1 ~ 4mm

Rear edge 4mm or less Total of both sides: 6mm or less

Image loss OC Same size 3mm or less

SPF/RSPF Same size 4mm or less

K. Auto duplex

Standard/ Option

Standard provision (MX-M182D/M202D/M232D only) (D D / D  S enable only when RSPF is installed) Not available for MX-M182

L. Paper exit / finishing

Paper exit section capacity

Full detection Upper stage: Yes (Job separator is installed)

Finishing None Electronic sort

capacity Offset function Ye s Staple function None

Face down 250 sheets

Lower stage: No (Copy/printer 250 sheets count detection)

A4/ 8.5" x 11" standard document  (6% coverage) 160 sheets

F. Multi copy

Max. number of multi copy 999 sheets

G. Warm-up time

Warm-up time 25 seconds or less Pre-heat Available Jam recovery Within 25 sec

MX-M182 SPECIFICATIONS 3-2

M. Additional functions

MX-M182

APS O AMS O Auto tray switching O Memory copy O Rotation copy O E-sort 

(Sorting function) E-sort 

(Grouping function) Rotation sort X Prevention of sky shot X Independent zooming O 1 set 2 copy O

Binding margin O Edge erase Center erase

Black/white reverse X 2in1/4in1 O Offset O Preheating O

Auto shut-off O

System setting O Counter O

Coin vendor support O

Auditor support O

Duplex X O Toner save O

Account control O

O : Available X : Not available

SPF: Disable OC: Enlargement is disable.

Default AB series: 10mm (5, 10, 15, 20mm) Inch series: 1/2 inch (1/4, 1/2, 3/4, 1 inch)

The conditions are set by the system setting.

(1) Copy total (2) Print total (3) Scan (4) Toner residual quantity

(Supporting the interface only)

(Set according to the destination)

(Copy/Printer/Scanner Number of control: 50)

MX-M182D/M202D/

M232D

SPF/RSPF: Disable OC: Enlargement is disable.



N. Other specifications

Photoconductor type OPC (Organic Photo Conductor) Photoconductor drum dia. 30mm Copy lamp WhiteCCFL Developing system Dry 2-component magnetic brush

development Charging system Saw teeth charging Transfer system (+) DC corotron Separation system (-) DC corotron Fusing system Heat roller Cleaning system Contact blade

O. Package form

Body Body / Accessories

P. E xtern al vi ew

External dimensions (With the bypass tray closed) Occupying area (With the bypass tray opened) Weight (Excluding developer)

Standard model D model

591mm(W) x 573mm(D)

883mm(W) x 573mm(D)

1-tray model:

29.4kg

1-tray model:

29.6kg (OC) 2-tray model:

35.0kg (OC) 1-tray model:

33.2kg (RSPF) 2-tray model:

38.6kg (RSPF)

Q. Power source

Voltage 100 - 127V 220 - 240V Frequency 50/60Hz common

R. Power consumption

Max. power consumption 1200W

S. Digital performance

Resolution Reading 400 x 600dpi (PHOTO mode)

Writing 600 x 600dpi

Gradation Reading 256 gradations

Writing Binary Memory (MAX) 256MB (with MX-EB14) Hard disk None

400 x 600dpi (AUTO exposure mode) 400 (main) x 600 (sub) dpi (TEXT mode)

MX-M182 SPECIFICATIONS 3-3

2. Print mode

A. Printing function

(1) Platform

Item Content

Support platform IBM PC/AT compatible machine

(2) Support OS

Main unit When MX-NB12 is installed

Windows 98/Me No No No No No No No

NT 4.0 SP5 or later No No No No No No No 2000 CD-ROM CD-ROM CD-ROM No CD-ROM CD-ROM CD-ROM XP CD-ROM CD-ROM CD-ROM No CD-ROM CD-ROM CD-ROM XPx64 CD-ROM CD-ROM CD-ROM No CD-ROM CD-ROM CD-ROM Server 2003 No No CD-ROM No CD-ROM CD-ROM CD-ROM Server 2003x64 No No CD-ROM No CD-ROM CD-ROM CD-ROM Vista CD-ROM CD-ROM CD-ROM No CD-ROM CD-ROM CD-ROM Vistax64 CD-ROM CD-ROM CD-ROM No CD-ROM CD-ROM CD-ROM Server 2008 No No CD-ROM No CD-ROM CD-ROM CD-ROM Server 2008x64 No No CD-ROM No CD-ROM CD-ROM CD-ROM Windows 7 CD-ROM CD-ROM CD-ROM No CD-ROM CD-ROM CD-ROM Windows 7x64 CD-ROM CD-ROM CD-ROM No CD-ROM CD-ROM CD-ROM

Mac 9.0-9.2.2 No No No No No No No

X 10.2.8 No No No No No Web No X 10.3.9 No No No No No Web No X 10.4.11 No No No No No CD-ROM No X 10.5- 10.5.8 No No No No No CD-ROM No X 10.6-10.6.4 No No No No No CD-ROM No

Twain/Button

Manager

SPLC

Custom

PCL6

Custom

PCL5e

Custom

PPD PC-FAX

When MX-FX13 is

installed

(3) Printer driver function

a. Windows version of SPLC driver

Function Overseas Description

Main Copies 1-999 Perform specified numbers of printing.

Collate Collate

Document Style 1-sided

N-up 2/4/6 Specified numbers of pages are printed on one sheet. N-up Order Z N-up Border Yes / N o Partition line is added for the plural pages printed on 1 sheet. User Setting Add/Delete Register the setting value for commonly-used driver. Image Orientation Portrait

Rotate 180 Degree Yes / N o Rotate data 180 degrees to print.

Paper Paper Size (paper size) A3 / B4 / A4 / B5 / A5 / A6 / B6 / Ledger /

Legal/ 8.5x13.4 / Foolscap / Folio / Letter /

Invoice / Executive / 8K / 16K / COM-10 /

DL / C5 / A2(Fit To Page) / Custom *1

Custom Paper Size (paper size)

Fit to Page  (Zoom setting)

Zoom (Zoom setting) 25-400% Fit to Page size 

(Zoom setting)

Paper Selection Auto

Output Center Tray / Upper Tray

A3 / B4 / A4 / B5 / A5 / A6 / B6 / Ledger /

Legal / 8.5x13.4/ Foolscap / Folio / Letter /

Invoice / Executive / 8K / 16K / COM-10 /

Uncollate

2-sided (Book)

2-sided (Tablet)

Landscape

1 size Width: 100 - 297mm

Ye s / N o Print size is changed according to the specified contents.

DL / C5

Bypass (Auto)

Bypass (Manual)

Tray 1/2 (3/4)

If "Collate" is specified, plural printing by the number of set is done, and "Uncollate" is specified, plural printing by page is done.

Simplex or duplex printing is done depending on the setting. Print direction is different depending on book/tablet for duplex printing. (* Simplex model have no duplex function.)

Print in the specified print direction.

Print in the specified paper size. Even if actual paper size is different from the specified paper size, the image is created in the specified paper size to print.

Length: 148 - 431.8mm

Paper is fed from the specified paper feed tray.

MX-M182 SPECIFICATIONS 3-4

Function Overseas Description

Advanced Brightness 

(Image adjustment)

0 - 100% Adjust the brightness of the image by moving the scale within the

range of 0-100. The illustration image at the upper left of the screen changes by this adjustment.

Contrast  (Image adjustment)

0 - 100%. Adjust the contrast of the image by moving the scale within the range

of 0-100. The illustration image at the upper left of the screen changes by this adjustment

Text To B l a ck Yes / N o Print documents created by CAD software in B/W to improve

visualization of colored line image/text. Vector To Black Ye s / N o Print lines in BW to improve visualization. Input Resolution

600dpi/300dpi Select input resolution (default: 600dpi)

(compatibility) Hatching Pattern

Standard/fine Select hatching pattern (default: standard)

(compatibility) Spool format

RAW/EMF Default: RAW

(compatibility) Reduction Method

Standard/By Object/ By page Default: Standard

(compatibility) Print density

1 - 5 stages Default: 3

(compatibility) Duplex print

Yes / N o Specify duplex printing function with giving priority to driver.

(Compatibility) Duplex Style

Pattern1/ Pattern2/ Pattern3 Default: 1

(compatibility) Print by number of copy

Yes / N o Specify print by set function with giving priority to driver.

(compatibility)

Water marks

Watermark None / TOP SECRET / CONFIDENTIAL /

DRAFT / ORIGINAL / COPY

Select watermark specified as default.

User Setting Add / Update / Delete Add, register and delete watermark. Position Center

Adjust the position of watermark vertically and horizontally.

X: ±50

Y: ±50 Size 6 - 300 Adjust the size of watermark. Angle ±90 Adjust the angle of watermark. Grayscale 0 - 255 Adjust the watermark density. Edit Font Ye s Edit font. Thick Letter Ye s / N o Italic Face Ye s / N o Character Set Ye s On First Page only Yes / N o Put watermark only on the first page.

Option ROPM On/Off

Paper Feed Option 1-Tray/2-Tray/3-Tray/4-Tray Auto Configuration Ye s Paper Tray (Tray Setting) Bypass Tray/Tray1/Tray2/Tray3/Tray4 Paper Size to Specify No specification/ A3 / B4 / A4 / B5 / A5 /

A6 / B6 / Ledger / Legal / 8.5x13.4 /

Foolscap / Folio / Letter / Invoice /

Executive / 8K / 16K / COM-10 / DL / C5 /

Custom Status Window Ye s Version Information Ye s

*1: Custom paper size range: Width 100 - 297.0 mm (3.94 -11.69 inch) Length 148 -431.8mm (5.83 - 17.00 inch)

MX-M182 SPECIFICATIONS 3-5

b. Windows version of PCL/PS Driver (PCL: MX-NB12 is expanded)

Function PCL6 PS

Main Copies 1-999 1-999

Image Orientation

Rotate 180 Degree Yes / N o Ye s / No

Collate Collate

Document Style 1-Sided, 2-Sided(Book) 2-Sided(Tablet),

Job Control Inform job end Ye s / N o Yes/No

Account Number Setting Yes/No (5 digits) Yes/No (5 digits)

Confirm Job Control Ye s / N o Ye s / N o Binding Edge N/A N/A Margin Shift N/A N/A N-up N-up 2/4/6/8/9/16 2/4/6/8/9/16

N-up Order Z Z

N-up Border Yes / N o Ye s / N o

Paper Paper Size Paper Size A3 / B4 / A4 / B5 / A5 / B6 / A6 / 11x17 /

Paper Type N/A N/A

Custom Paper Size 1 size 1 size Zoom Setting Fit to Page Ye s / N o Ye s / N o

Zoom 25-400%

XY-Zoom N/A Width: 25 - 400%

Fit to Page size A3 / B4 / A4 / B5 / A5 / B6 / A6 / 11x17 /

Paper Selection Auto

Advanced Graphics mode Raster/Vector N/A

Mirror Image N/A Horizontal Vertical PostScript

Option Bitmap Compression None / Very High Quality / High Quality /

Compression Options

Compatibility Input Resolution 600/300 dpi N/A

Overlay ON/OFF ON/OFF Font Setting Ye s

PS Error Information N/A Ye s / N o

PS Pass-Through N/A Ye s / N o

Job Compression N/A None / Fastest / Fast / Medium /

Bitmap Compression N/A None / Very High Quality / High Quality /

Halftone Setting N/A N/A

Hatching Pattern Standard/Fine N/A

Spool Format RAW/EMF N/A

Print Density 1-5 Stages 1-5 Stages

Print by set (Give priority

to Driver Setting)

Duplex Printing (Give

Priority to Driver Setting)

Negative Image N/A N/A

Mirror Image N/A N/A

Zoom N/A N/A

Duplex Style Pattern1/ Pattern2/ Pattern3 Pattern1 / Pattern2 / Pattern3

Pamphlet Style (Tiled Pamphlet),

Pamphlet Style (2-up Pamphlet)

8.5x14 / 8.5 x 13.4/ 8.5x13 / 8.5x11 / 5.5x8.5 / Folio / Executive / COM-10 / DL / C5/ 8K /

16K / A0 (Fit To Page) / A1(Fit To Page)/

A2(Fit To Page) / Custom *1

Reference Point: Upper left/Center

8.5x14 / 8.5 x 13.4 / 8.5x13 / 8.5x11 /

5.5x8.5 / Folio / Executive / COM-10 / DL /

Portrait

Landscape

Uncollate

1-Sided, 2-Sided(Book) 2-Sided(Tablet),

Pamphlet Style (Tiled Pamphlet),

Pamphlet Style (2-up Pamphlet)

A3 / B4 / A4 / B5 / A5 / B6 / A6 / 11x17 /

8.5x14 / 8.5 x 13.4/ 8.5x13 / 8.5x11 / 5.5x8.5 / Folio / Executive / COM-10 / DL / C5 / 8K /

N/A

Reference Point: Upper left/Center

A3 / B4 / A4 / B5 / A5 / B6 / A6 / 11x17 /

8.5x14 / 8.5 x 13.4 / 8.5x13 / 8.5x11 /

5.5x8.5 / Folio / Executive / COM-10 / DL /

C5 / 8K / 16K

Bypass (Auto)

Bypass (Manual)

Tray 1/2/3/4

Medium Quality / Draft

Yes / N o N/A

Resident Font: 80 fonts

Portrait

Landscape

Collate

Uncollate

16K / Custom *1

Length: 25 - 400%

Lock Aspect Ratio: On/Off

C5 / 8K / 16K

Auto

Auto Bypass (Auto)

Bypass (Manual)

Tray 1/2/3/4

N/A

Best Compression

Medium Quality / Draft

Ye s

Resident Font: 80 fonts

MX-M182 SPECIFICATIONS 3-6

Function PCL6 PS

Advanced Image

Adjustment

Brightness 0 - 100% 0 - 100%

Contrast 0 - 100% 0 - 100% Text To B lack Yes / N o Ye s / No Vector To Black Yes / N o Ye s / No Right binding Ye s / N o Yes / N o

Water marks Watermark None / TOP SECRET / CONFIDENTIAL /

DRAFT / ORIGINAL / COPY

None / TOP SECRET / CONFIDENTIAL /

DRAFT / ORIGINAL / COPY User Setting Add / Update / Delete Add / Update / Delete Position Center

X: ±50

Y : ±50

Center

X: ±50

Y : ±50 Size 6 - 300 6 - 300 Angle ±90 ±90 Grayscale 0 - 255 0 - 255 Edit Font Ye s Yes Thick Letter Ye s / N o Ye s / N o Italic Face Ye s / N o Ye s / N o Character Set Ye s Yes Print Pattern Transparent 1 / Transparent 2 / Overlap /

Transparent / Overlap / Outline

Outline Frame Line None/rectangle/Circle None/rectangle/Circle On First Page only Yes / N o Ye s / No

Special Mode Page Interleave Yes N/A

Paper Insertion Setting

Different 1st (Cover) and Last Page

1st Page: On/Off

(Last Page Not Support)

1st Page : On/Off

(Last Page Not Support) Duplex Printing Ye s / N o Ye s / N o Paper Tray Bypass (Auto)

Bypass(Manual)

Tray 1/2/3/4

Bypass (Auto)

Bypass(Manual)

Tray 1/2/3/4 Transparency Inserts N/A N/A Carbon Copy N/A N/A

Option ROPM On/Off On/Off

Paper Feed Option 1-Tray/2-Tray/3-Tray/4-Tray 1-Tray/2-Tray/3-Tray/4-Tray Job Separator On/Off On/Off Option Auto Setting Ye s Ye s Tray Setting Paper Tray Bypass Tray/ Tray1/Tray2/Tray3/Tray4 Bypass Tray/ Tray1/Tray2/Tray3/Tray4

Paper Size to Specify Not Specified/ A3 / B4 / A4 / B5 / A5 / A6 /

B6 / Ledger / Legal / 8.5x13.4 / Foolscap /

Folio / Letter / Invoice / Executive / 8K / 16K /

COM-10 / DL / C5 / Custom)

Not Specified/ A3 / B4 / A4 / B5 / A5 / A6 / B6 / Ledger / Legal / 8.5x13.4 / Foolscap /

Folio / Letter / Invoice / Executive / 8K / 16K /

COM-10 / DL / C5 / Custom) Print Policy Ye s Yes Font N/A Ye s Version Information Ye s Yes

*1: Custom paper size range: Width 100 - 297.0 mm (3.94 -11.69 inch) Length 148 -431.8mm (5.83 - 17.00 inch)

MX-M182 SPECIFICATIONS 3-7

C. Windows version/Mac version of PPD Driver

Function WinPPD Mac PPD Copies Ye s Ye s Collate/Uncollate Ye s Ye s N-UP Ye s Ye s N-up Order No Ye s N-up Border No Ye s Duplex Ye s Ye s Retention No No Document Filling No No User Authentication No No User Number No Ye s Job ID (User Name/ Job Name) Color Mode No No Print Mode No No Image Type No No Neutral Gray No No Pure Black Print No No Black Over Print No No Toner Save No No Color Adjustment No No Source Profile No No Rendering Intent No No Output Profile No No Screening No No Simulation Profile No No Paper Size A3 / B4 / A4 / B5 / A5 /

Executive / COM-10 /

Output Tray Upper Tray Center Tray Upper Tray Center Tray

*1: Custom paper size range: Width 100 - 297.0 mm (3.94 -11.69 inch) Length 148 -431.8mm (5.83 - 17.00 inch)

No Ye s

B6 / A6 / 11x17 /

8.5x14 / 8.5 x 13.4/

8.5x13 / 8.5x11 /

5.5x8.5 / Folio /

DL / C5/ 8K / 16K/

Custom*1

A3 / B4 / A4 / B5 / A5 /

B6 / A6 / 11x17 /

8.5x14 / 8.5 x 13.4/

8.5x13 / 8.5x11 /

5.5x8.5 / Folio /

Executive / COM-10 /

DL / C5 / 8K / 16K /

A0 (Fit To Page) / A1 (Fit

To Page) / A2 (Fit To

Page) / Custom*1

3. Scanner mode

A. Scanner function

(1) Mode

Mode Sub Mode

Scanner E-mail Ye s 

FTP Server Network Folder (SMB) No Desktop Ye s  USB Memory

Twain Scan  (Including Button Manager)

– Ye s

(MX-NB12 is expanded)

(2) Support Image (MX-NB12 is expanded)

Mode Mode Ty pe Support

Scanner (MX-NB12 is expanded)

File Format (B/W)

File Format (Gray Scale)

File Format (Color)

TIFF Ye s PDF Ye s PDF/A N/A Encrypted PDF N/A XPS N/A TIFF Ye s JPEG Ye s PDF Ye s PDF/A N/A Encrypted PDF N/A Compact PDF (ACRE installed) N/A XPS N/A TIFF Ye s JPEG Ye s PDF Ye s PDF/A N/A Encrypted PDF N/A Compact PDF (ACRE installed) N/A XPS N/A

(3) Image Processing

Mode Scanner (MX-NB12 is expanded)

Exposure Adjustment Auto Ye s

Manual 5 levels

Original Type *1 Te x t Ye s

Photo Ye s Auto Ye s

Resolution (Different depending on file format/ sending method)

*1: This setting can only be set at the B/W mode

75 x 75 dpi 100x100dpi 150x150dpi 200x200dpi 300x300dpi 400x400dpi 600x600dpi

(4) Push Scan (Button Manager)

Support OS Windows 2000 Professional/Windows XP Home Edition/

Hardware Environment

Selectable destination

File Format TIFF/PDF/BMP

Windows XP Professional/Windows Vista/Windows 7 (System) Shall meet the operating conditions of each OS

basically. (HDD) 8MB or more: 100MB or more is recommended (Monitor) 800x600 dots or more

Shall be able to display 256 colors or more. (Other) USB port (2.0) Sharpdesk/ E-mail software/ Fax software/ OCR software/ MS Word/ Any directory

MX-M182 SPECIFICATIONS 3-8

(5) Pull Scan (TWAIN)

USB TWAIN (Does not function in Network system) Support OS Windows 2000 Professional/Windows XP Home Edition/ Windows XP Professional/ Windows Vista/Windows 7 Interface USB Hardware Environment (System) Shall meet the operating conditions of each OS basically.

Two-sided Scan Ye s Color Mode B/W(Mono2)/ B/W(Error Diffusion)/Gray Scale/Full Color Resolution 75dpi/ 100dpi/ 150dpi/ 200dpi/ 300dpi/ 400dpi/ 600dpi Or Custom: 50 - 9600dpi (simulated) Scanning Range A3/ A4/ A4-R/ A5/ A5-R/ B4/ B5/ B5-R/ Ledger/ Letter/ Letter-R/ Executive/ Executive-R/ Foolscap/ Invoice/

Preview Function Yes Zoom Preview Function Ye s Rotation Scan Yes (90 / 180/ 270 degrees) Quick Scan No Brightness/Contrast Adjustment Auto/ Manual(-100 - +100) Gamma Adjustment Ye s Color Matching None/ Printer/ CRT/ LCD display/ ICM Edge Emphasis None/ Normal/ High/ Fuzzy B/W Reverse Yes Selection of Light Source Color Yes (Red/ Green/ Blue/ White) Threshold Setting Auto/ Manual (1-254) Addition of Void Area Available (Lead Edge/Trail Edge: 2.5mm Right/Left: 3.0mm) Storing of Setting Contents Ye s Keeping of Preview Image Ye s Unit of Display for Scanning Range Pixel/ mm/ inch Notes' Security Feature No

(HDD) 8MB or more: 100MB or more is recommended (Monitor) 800x600dots or more Shall be able to display 256 colors or more. (Other) USB port

Invoice-R/ Legal/ 8.5x13.4/ 8.5x13.5(343x216mm)/ Postcard/ 8K/ 16K/ 16K-R/ Auto/ User Definition

(6) Network Push Scan (MX-NB12 is expanded)

a. Specification

Support OS Windows 2000 Professional/Windows XP Home Edition/ Windows XP Professional/Windows Vista/Windows 7 Scan Resolution 75x75, 100x100, 150x150, 200x200, 300x300, 400x400, 600x600dpi (main direction x sub direction) Interface USB 2.0, 10/100BASE-TX Support Server/Protocol TCP/IP, SMTP, LDAP, FTP Output file format B&W : PDF (w/o compression, G3, G4), TIFF (w/o compression, G3, G4) 

2-sided original scan Ye s Optical Resolution 400x600dpi File creation File per 1 to 6 page / 1 file for all pages Sending method/Linkage File server sending scan

Density 1 - 5 Light Source Yes (Red/ Green/ Blue/ White) Voi d Area Ye s Control System Embedded Web server Recommended Web browser Internet Explorer6.0 or later Support Mail system Mail server supporting SMTP, Mail server supporting POP3 Addressing Rapid / Group / Indication by Direct Address Input / Selection from LDAP Server Number of registration of

destination

Utility Sharpdesk

Color/Gray scale: JPEG, PDF(JPEG), TIFF(JPEG)  TIFF/PDF supports multi page.

Desktop sending scan E-mail sending scan USB memory scan

Max. 200 All destination including E-mail, File server, Desktop and Group. Multiple E-mail addresses can be registered as a group and as 1 destination (max. 100). In this case, number of registration of destination may be less than 200.

MX-M182 SPECIFICATIONS 3-9

b. Scanner Setting

Key Grouping Selectable items Remark

Color Mode Color Mode *Color

Gray

Set the scan color *Default is Color.

Monochrome

Format Format and Compression method TIFF

TIFF G3

Specify file format.

*Default is PDF TIFF G4 *PDF PDF G3 PDF G4 JPEG

Multi-file/Single file Single : 1 page / file

*Multi : All pages / file Multi : 2 pages / file Multi : 3 pages / file

Specify Single or Multi.

Single: 1 page / file

Multi: Plural pages / file

*Default: All pages / file Multi : 4 pages / file Multi : 5 pages / file Multi : 6 pages / file

Resolution Resolution 75dpi

100dpi

Set the output resolution

*Default: 150dpi *150dpi 200dpi 300dpi 400dpi 600dpi

Duplex 1-side / 2-sided original *1-side

2-sided

Set the original type whether 1-side or 2-sided.

This menu will appear when RSPF is installed.

If 2-sided is specified, original is scanned only by RSPF.

*Default: 1-side

Vertical original (set vertical) Horizontal original (set vertical) Vertical original (set horizontal) Horizontal original (set horizontal)

Original size Scan size A3/B4/A4/A4R/B5/B5R/A5/A5 Set the scan size.

MX-M182 SPECIFICATIONS 3-10

[4] CONSUMABLE PARTS

1.Supply system table

A. North America, Middle America, South America

No. Name Product name Content Life Remark

1 Toner cartridge(Black) MX-235NT Toner cartridge

Vinyl bag

2 Developer MX-235NV Developer x1 50K 3 Drum KIT AR-205DR Drum

Drum fixing plate

B. Brazil

No. Name Product name Content Life Remark

1 Toner cartridge(Black) MX-235BT Toner cartridge

Vinyl bag 2 Developer MX-235NV Developer x1 50K 3 Drum KIT AR-205DR Drum

Drum fixing plate

C. Europe

No. Name Product name Content Life Remark

1 Toner cartridge(Black) MX-235GT Toner cartridge

Vinyl bag 2 Developer MX-235GV Developer x1 50K 3 Drum KIT AR-205DM Drum

Drum fixing plate

x1x116K

Default is Toner save mode. Life is 19K. (200V series)

x1 x150K

x1x116K Life setting by A4 6% document

x1 x150K

x1x116K Life setting by A4 6% document

x1 x150K

Life setting by A4 6% document



D. Australia/New Zealand

No. Name Product name Content Life Remarke

1 Toner cartridge(Black) MX-235GT Toner cartridge

Vinyl bag 2 Developer MX-235GV Developer x1 50K 3 Drum KIT AR-205DM Drum

Drum fixing plate

x1x116K Life setting by A4 6% document

x1x150K

E. Middle East, Africa (except Iran) /Israel/Philippines/Others

No. Name Product name Content Life Remark

1 Toner cartridge(Black) MX-235FT Toner cartridge

Vinyl bag 2 Toner cartridge(Black) MX-236FT Toner cartridge

Vinyl bag 3 Developer MX-235FV Developer x1 50K 4 Drum KIT AR-205DR Drum

Drum fixing plate

x1x116K Life setting by A4 6% document

x1x18.4K Life setting by A4 6% document

50K

F. Ta iw an

No. Name Product name Content Life Remark

1 Toner cartridge(Black) MX-235FT Toner cartridge

Vinyl bag 2 Toner cartridge(Black) MX-236FT Toner cartridge

Vinyl bag 3 Developer MX-235FV Developer x1 50K 4 Drum KIT AR-205DR Drum

Drum fixing plate

x1x116K Life setting by A4 6% document

x1x18.4K Life setting by A4 6% document

x1x150K

MX-M182 CONSUMABLE PARTS 4-1

G. Asia(Except the above)/Thailand/Hong Kong

No. Name Product name Content Life Remark

1 Toner cartridge(Black) MX-235AT Toner cartridge

Vinyl bag 2 Toner cartridge(Black) MX-236AT Toner cartridge

Vinyl bag 3 Developer MX-235AV Developer x1 50K 4 Drum KIT AR-205DR Drum

Drum fixing plate

x1x116K Life setting by A4 6% document

x1x18.4K Life setting by A4 6% document

x1x150K

2. Environmental conditions

A. Transport conditions

(1) Transport conditions

Humidity (%)

B. Use conditions

Use environment conditions

Humidity (%)

Temperature

(2) Storage conditions

Humidity (%)

Temperature

C. Life(packed conditions)

Photoconductor drum (36 months from the production month) Developer, toner (24 months from the production month)

Temperature

MX-M182 CONSUMABLE PARTS 4-2

3. Production number identification

The label on the toner cartridge shows the date of production.

The lot number, printed on the front side flange, is composed of 10 digits, each digit showing the following content:

1 2 3 4 5 6 7 8 9 10

The lot number is of 10 digits. Each digit indicates the content as follows. The number is printed on the flange on the front side.

place

Serial

number

Year/ Month/ Day

Ver.No.Production

1: Number

For this model, this digit is 2.

2: Alphabet

Indicates the model conformity code. G for this model.

3: Number

Indicates the end digit of the production year.

4: Number or X, Y, Z

Indicates the production month. X stands for October, Y November, and Z December.

5/6: Number

Indicates the day of the production date.

7: Number

Indicates the day of the month of packing. X stands for October, Y November, and Z December.

8/9: Number

Indicates the day of the packing date.

10: Alphabet

Indicates the production factory.

MX-M182 CONSUMABLE PARTS 4-3

[5] EXTERNAL VIEWS AND INTERNAL STRUCTURES

1. Appearance

17 18

1 USB 2.0 port Connect to your computer to this port to use the printer and scanner functions. 2 Charger cleaner Use to clean the transfer charger. 3 Glass cleaner Use to clean the original scanning glass. 4 Document glass Place an original that you wish to scan face down here. 5 Handles Use to move the machine. 6 Power switch Press to turn the machine power on and off. 7 Centre tray Copies and printed pages are output to this tray. 8 Top tray (when the job separator tray kit is installed) Received faxes (when the fax option is installed) and print jobs are delivered to this tray. 9 Operation panel Contains operation keys and indicator lights.

10 Front cover Open to remove paper misfeeds or replace the toner cartridge. 11 Tray 1 Tray 1 can hold approximately 250 sheets of copy paper (80 g/m2 (20 lbs.)). 12 Tray 2 Tray 2 can hold approximately 250 sheets of copy paper (80 g/m2 (20 lbs.)). 13 Document cover (when installed) Open to make a copy from the document glass. 14 Side cover Open to remove misfeed paper. 15 Side cover handle Pull to open the side cover. 16 Bypass tray guides Adjust to the width of the paper when using the bypass tray. 17 Bypass tray Special paper (heavy paper or transparency film) can be fed from the bypass tray. 18 Bypass tray extension Pull out when feeding large paper such as A3 and B4 (11" x 17" and 8-1/2" x 14").

MX-M182 EXTERNAL VIEWS AND INTERNAL STRUCTURES 5-1

2. Internal

21 22

2526

28 29

19 Toner cartridge lock release lever To replace the toner cartridge, pull out the toner cartridge while pushing on this lever. 20 Toner cartridge Contains toner. 21 Document feeder tray (when the SPF/

RSPF is installed)

22 Original guides (when the SPF/RSPF is

installed)

23 Feeding roller cover (when the SPF/

RSPF is installed)

24 Right side cover (when the SPF/RSPF is

installed) 25 Fusing unit release levers To remove the paper misfeed in the fusing unit, push down on these levers and remove the paper. 26 Roller rotating knob Rotate to remove misfeed paper. 27 Exit area (when the SPF/RSPF is

installed) 28 Photoconductive drum Images are formed on the photoconductive drum. 29 Fusing unit paper guide Open to remove misfeed paper.

Warning: The fusing unit is hot. Do not touch the fusing unit when removing misfeed paper. Doing so may cause a burn or injury.

Do not touch the photoconductive drum (green portion) when removing the misfeed paper. Doing so may damage the drum and cause smudges on copies.

Note: The model name is on the front cover of the machine.

Place the original(s) that you wish to scan face up here. Up to 40 sheets can be placed.

Adjust to the size of the originals.

Open to remove misfeed originals.

Originals exit the machine here after copying/scanning when the SPF/RSPF is used.

MX-M182 EXTERNAL VIEWS AND INTERNAL STRUCTURES 5-2

3. Operation Section

12345

01 02 03 04 05

06 07 08 09 10

11 12 13 14 15

16 17 18 19 20

21 22 23 24 25

SPEAKER

SHIFT

REDIAL/PAUSE

SPEED

SYMBOL

COMM. SETTING

SPACE/–

COPY

SCAN

FAX

ON LINE DATA

LINE DATA

FAX STATUS

SPECIAL

FUNCTION

EXPOSURE

COPY

COLOUR MODE

SCAN

PROGRAM

FAX

13 14 15

1 Keys for fax function (when the fax

These are used in fax mode.

6 7 8 9 10 11 12

INTERRUPT

COPY RATIO

PAPER SELECT

ADDRESS

RESOLUTION

ADDRESS

RESOLUTION

AUTO IMAGE

FORMAT

BROADCAST

OUTPUT ORIGINAL SIZE ORIGINAL SIZE

2-SIDED COPY DUPLEX SCAN DUPLEX SCAN

BACK

ABC DEF

ACC. #-C

JKLGHI MNO

TUVPQRS WXYZ

@.-

READ-END

16 17 18 19 20 21 22 23 24 25 26

option is installed)

2 [COPY] key / indicator Press to select copy mode. If pressed when "Ready to copy." appears or during warm-up, the total

number of sheets used appears while the key is pressed.

3 [PRINT] key / indicator Press to select print mode.

• ONLINE indicator Print jobs can be received when this indicator is lit.

• DATA indicator This lights steadily when there is a print job in memory that has not been printed, and blinks

during printing.

4 [SCAN] key / indicator Press to select scan mode. To use the machine as a network scanner, see the "Operation Guide

(NETWORK EXPANSION KIT)" that accompanies the machine.

5 [FAX STATUS] key (when the fax option

This key is used in fax mode.

is installed) 6 Display Shows various messages. 7 [BACK] key Press to return the display to the previous screen. 8 Copy number display The selected number of copies appears. During copying, this shows the remaining number of

copies.

9 [OK] key Press to enter the selected setting.

10 Numeric keys Use to select the number of copies. 11 [C] key Press to clear the set number of copies or stop a copy run. 12 [INTERRUPT] key ( ) / INTERRUPT

Interrupts a copy run to allow an interrupt copy job to be performed.

indicator

13 [FAX] key / indicator (when the fax option

is installed)



This key is used in fax mode.

LINE indicator, DATA indicator

14 [SPECIAL FUNCTION] key Press to select special functions. 15 [EXPOSURE] key Use to select the exposure mode. "AUTO", "TEXT", or "PHOTO" can be selected. 16 [PAPER SELECT] key Use to manually select a paper tray. 17 [COPY RATIO] key Press to select a reduction or enlargement copy ratio. 18 [AUTO IMAGE] key Press to have the copy ratio selected automatically. 19 [OUTPUT] key Use to select the sort function. 20 [2-SIDED COPY] key 

Select the two-sided copying mode.

(MX-M182D/MX-M202D/MX-M232D)

21 Arrow keys Press to move the highlighting (which indicates that an item is selected) in the display. 22 [ACC.#-C] key ( ) Press the end the use of an account and return the display to the account number entry screen. 23 [0] key Press during a continuous copy run to display the number of copies completed. 24 [READ-END] key ( ) When copying in sort mode from the document glass, press this key when you have finished scanning

the original pages and are ready to start copying. 25 [CA] key Clears all selected settings and returns the machine to the default settings. 26 [START] key ( ) / indicator Copying is possible when this indicator is on. Press the key to start copying. This indicator blinks when

auto power shut-off mode has activated. Press the key to return to normal operation.

MX-M182 EXTERNAL VIEWS AND INTERNAL STRUCTURES 5-3

4. Motor, solenoid, clutch

113

4 6

910

No. Name Code Function operation

1 Mirror motor MRM Drives the optical mirror base (scanner unit). 2 Toner motor TM Toner supply 3 Duplex motor DPX Switchback operation and paper exit motor in duplex. (MX-M182D/M202D/M232D) 4 Main motor MM Drives the machine. 5 1st tray paper feed clutch CPSCL1 Drives the pick up roller 6 PS clutch RRC Drives the resist roller 7 Bypass tray paper transport clutch MPTC Drives the bypass tray paper transport roller. 8 Bypass tray paper feed solenoid MPFS Bypass tray paper feed solenoid

9 2nd tray transport clutch FSCL1 Drives the 2nd tray transport roller. (MX-M202D/M232D) 10 2nd tray paper feed clutch PSCL2 Drives the 2nd tray paper feed roller. (MX-M202D/M232D) 11 Exhaust fan motor PSFM Cools the inside of the machine. 12 Cooling fan motor VFM Cools the inside of the machine. 13 Shifter motor SFTM Drives the shifter motor.

MX-M182 EXTERNAL VIEWS AND INTERNAL STRUCTURES 5-4

5. Sensor, switch

(AB)

(INCH)

(AB)

(INCH)

18 4

No. Name Code Function operation

1 Mirror home position sensor MHPS Detects the mirror (scanner unit) home position.

2 Side door switch DSWR Side door open detection

3 Paper exit sensor (paper exit side) POD1 Detects paper exit.

4 Paper exit sensor (DUP side) PDPX Paper transport detection

5 Thermistor RTH Fusing section temperature detection

6 Thermostat RDTCT Fusing section abnormally high temperature detection

7 Toner density sensor TCS Detects the toner density in the developing unit.

8 2nd tray detection switch CSD2 2nd tray detection

9 Bypass tray sensor MPED Bypass tray transport detection 10 2nd tray door open/close sensor DRS2 2nd tray door open/close detection (MX-M202D/M232D) 11 2nd tray door paper pass sensor PPD2 2nd tray paper entry detection (MX-M202D/M232D) 12 2nd tray paper empty sensor CSS2 2nd tray paper empty detection (MX-M202D/M232D) 13 Paper in sensor PIN Paper transport detection 14 Tray empty CSS1 Tray paper entry detection 15 Front cover SW DSWF Front cover open detection 16 Power switch MAIN SW Turns ON/OFF the main power source. 17 OC sensor OCSW Original cover and SPF open/close detection 18 Shifter home position sensor SFTHP Shifter home position detection 19 Original size sensor(Main Scaning) DSIN0 Original size detection 20 Original size sensor(Sub Scaning) DSIN1 Original size detection

MX-M182 EXTERNAL VIEWS AND INTERNAL STRUCTURES 5-5

6. PWB unit

No. Name Function operation

1 Copy lamp Inverter PWB Copy lamp control

2 CCD sensor PWB Image scanning

3 Main control PWB Main control PWB

4 2nd tray PWB 2nd tray control

5 High voltage PWB High voltage control

6 Power PWB AC power input/DC power control

7 Operation main PWB Operation panel input/Display, operation panel section control

8 USB I/F PWB Connect a USB device

9 LCD OPE PWB Display and operation panel control

MX-M182 EXTERNAL VIEWS AND INTERNAL STRUCTURES 5-6

7. Cross sectional view

563

9 10 11 12

23 22

13 14

1617192021

No. Name Function/Operation

1 Copy lamp Image radiation lamp 2 Copy lamp unit Operates in synchronization with No. 2/3 mirror unit to radiate documents

sequentially. 3 LSU unit Converts image signals into laser beams to write on the drum. 4 Lens unit Reads images with the lens and the CCD. 5 MC holder unit Supplies negative charges evenly on the drum. 6 Paper exit roller Used to discharge paper. 7 Transport roller Used to transport paper. 8 Upper heat roller Fuses toner on paper (with the teflon roller). 9 Lower heat roller Fuses toner on paper (with the silicon rubber roller).

10 Waste toner transport roller Transports waste toner to the waste toner box. 11 Drum unit Forms images. 12 Transfer charger unit Transfer images (on the drum) onto paper. 13 DUP follower roller Transports paper for duplex. 14 Duplex transport roller Transports paper for duplex . 15 Resist roller Takes synchronization between the paper lead edge and the image lead edge. 16 Bypass tray Bypass tray 17 Bypass tray paper pick up roller Picks up paper in bypass tray. 18 No. 2/3 mirror unit Reflects the images from the copy lamp unit to the lens unit. 19 Bypass tray transport roller Transports paper from the bypass tray. 20 2nd tray paper transport roller Transports paper from the 2nd tray. (MX-M202D/M232D) 21 2nd tray paper pick up roller Picks up paper from the 2nd tray. (MX-M202D/M232D) 22 1st tray paper feed roller Picks up paper from the 1st tray. 23 MG roller Puts toner on the OPC drum.

MX-M182 EXTERNAL VIEWS AND INTERNAL STRUCTURES 5-7

[6] ADJUSTMENTS

20mm

150mm

DV front cover

Developing doctor gap

Both ends (20mm from the both ends) :

C (Center) (150mm from the both ends) :

1.5 0.1mm

1. Adjustment item list

Section Adjustment item Adjustment procedure/SIM No.

A Process

section

B Mechanism

section

C Image density

adjustment

2. Copier adjustment

A. Process section

(1) Developing doctor gap adjustment

1) Loosen the developing doctor fixing screw A.

2) Insert a thickness gauge of 1.5mm to the three positions at 20mm and 150mm from the both ends of the developing doctor as shown.

(1) Developing doctor gap adjustment Developing doctor gap adjustment (2) MG roller main pole position adjustment MG roller main pole position adjustment (3) Developing bias voltage check (4) Main charger voltage check (1) Image position adjustment SIM-50 (2) Main scanning direction (FR direction) distortion balance

adjustment

(3) Main scanning direction (FR direction) distortion adjustment Rail height adjustment (4) Sub scanning direction (scanning direction) distortion

adjustment

(5) Main scanning direction (FR direction) magnification ratio

adjustment

(6) Sub scanning direction (scanning direction) magnification ratio

adjustment

(7) Off center adjustment OC mode (SIM 50-12)

(1) Copy mode SIM 46-2

No. 2/3 mirror base unit installing position adjustment Copy lamp unit installing position adjustment

Winding pulley position adjustment

SIM 48-1

OC mode in copying (SIM 48-1) SPF mode in copying (SIM 48-5)

SPF mode (SIM 50-12)

(2) MG roller main pole position adjustment

1) Remove the DV front cover, and put the developing tank on a flat surface.

2) Tie a string to a needle or a pin.

3) Hold the string and bring the needle close to the MG roller horizontally. (Do not use paper clip, which is too heavy to make a correct adjustment.) (Put the developing unit horizontally for this adjustment.)

4) Do not bring the needle into contact with the MG roller, but bring it to a position 2 or 3mm apart from the MG roller. Mark the point on the MG roller which is on the extension line from the needle tip.

5) Measure the distance from the marking position to the top of the doctor plate of the developing unit to insure that it is 18mm. If the distance is not within the specified range, loosen the fixing screw A of the main pole adjustment plate, and move the adjustment plate in the arrow direction to adjust.



3) Push the developing doctor in the arrow direction, and tighten the fixing screws of the developing doctor in the sequence of 132

4) Check the clearance of the developing doctor. If it is within the specified range, then fix the doctor fixing screw with screw lock.

* When inserting a thickness gauge, be careful not to scratch the

developing doctor and the MG roller.

33.

MX-M182 ADJUSTMENT 6-1

(3) Developing bias voltage check

(Mode selection window 1)

Sim50-1 LEAD EDGE

1:TRAY1 2:TRAY2 3:MFT 1/2 [ 1- 99]

50 50

(Mode selection window 2)

Sim50-1 LEAD EDGE 4:DEN-A

5:RRC-A 6:DEN-B 2/2 [ 1- 99]

Ready to copy.

100%

(Copy start window)

Copies in progress.

100%

(Copy execution window)

Note:Use a digital multi-meter with an internal resistance of 10M or

more.

1) Set the digital multi-meter range above 500 Vdc.

2) Put the test rod of the digital multi-meter on the developing bias voltage output check pin.

3) Turn on the power, execute SIM25-1.

B. Mechanism section

(1) Image position adjustment

a. OC image lead edge position adjustment (SIM 50-1)

Note:In advance to this adjustment, the sub scanning magnification ratio

adjustment must be performed.

1) Set a scale on the OC table as shown below.

2) Make a copy.

3) Check the copy output. If necessary, perform the following adjustment procedures.

4) Execute SIM 50-01. Select a desired mode with the arrow keys, enter the adjustment value with 10-key, and press [OK] key. When [START] key is pressed, a sheet is printed.



Mode Specification Developing bias voltage DC - 400±10V

(4) Grid bias voltage check

Note:Use a digital multi-meter with an internal resistance of 10M or

more.

1) Set the digital multi-meter range above 600 Vdc.

2) Put the test rod of the digital multi-meter on the grid bias voltage output check pin.

3) Turn on the power.  (The voltage is outputted in the grid bias High output mode during warming up, and in the grid bias Low output mode when warming up is completed.)

Mode Specification Grid bias LOW DC - 380±8V Grid bias HIGH DC - 525±10V

Adjustment

mode

OC image lead edge position

Main cassette

SIM Display

text array

SIM

RRC-A R/0.1 Lead edge

50-1

TRAY1 H/0.1

Set

value

Spec

value

void: 1 - 4mm

Set

range

1 - 99

print start position

2nd cassette print start

TRAY2

Image loss: 3mm or less

position Multi bypass

MFT tray print start position

Lead edge void DEN-A B/0.05

5) Set the OC lead edge position set value (RRC-A) to [1] The OC image scanning start position is shifted inside the document edge.

6) Set the main cassette lead edge void adjustment value (DEN-A)* to [1] The lead edge void becomes the minimum.



MX-M182 ADJUSTMENT 6-2

7) Set the main cassette print start position value (TRAY1) to [1] and

2.5mm

(Mode selection window)

Ready to copy.

100%

(Copy start window)

Copies in progress.

100%

(Copy execution window)

Sim50-6 SPF EDGE

1:SIDE1 2:SIDE2 3:END EDGE

[ 1- 99]

50 50

make a copy.



The print start position is shifted inside the document edge.

5mm

*The dimension varies depending on the model.

4mm

8) Measure the image loss R of the copied image. Enter the set value of the image scanning lead edge position (RRC-A) again.

• 1 step of the set value corresponds to about 0.1mm shift.

• Calculate the set value from the formula below.

R/0.1(mm) = Image loss set value <R: Image loss measurement value (mm)>

10) Set the lead edge void adjustment value (DEN-A)* again.

• 1 step of the set value corresponds to about 0.1mm shift.

• Calculate the set value from the formula below. B/0.05 (mm) = Lead edge void adjustment value <B: Lead edge void (mm)>

Example: When setting the lead edge void to 2.5mm

:2.5 /0.05 = about 50

Note:If the set value is not obtained from the above formula, perform the

fine adjustment.

5mm

* The scanning edge is set. (A line may be printed by scanning the document edge.)

0mm

Example: 4/0.1 = 40 = about 40 Note:If the set value is not obtained from the above formula, perform the

fine adjustment.

9) Measure the distance H between the paper lead edge and the image print start position. Set the image print start position set value (TRAY1) again.

• 1 step of the set value corresponds to about 0.1mm shift.

• Calculate the set value from the formula below.

H/0.1(mm) = Image print start position set value <H: Print start position measurement value (mm)>

0mm

b. SPF image lead edge position adjustment (SIM50-6)

1) Set a scale on the OC table as shown below.

Note:Since the printed copy is used as a test chart, put the scale in

parallel with the edge lines.

2) Make a copy, Then use the copy output as an original to make an SPF copy again.

3) Check the copy output. If necessary, perform the following adjustment procedures.

4) Execute SIM 50-6.

5) Set the SPF lead edge position set value (SIDE1) so that the same image is obtained as that obtained in the previous OC image lead edge position adjustment.

Example: 5/0.1 = 50 = about 50 Note:If the set value is not obtained from the above formula, perform the

fine adjustment.

*Fit the print edge with the paper edge, and perform the lead edge adjustment.

MX-M182 ADJUSTMENT 6-3

Scale image

Paper rear edge

Void amount (Standard value: 4mm or less)

Sim50-10

PRT. CENTER

1:TRAY1 2:TRAY2 3:TRAY3 1/2 [ 1- 99]

50 50

Sim50-10

PRT. CENTER

4:TRAY4 5:BYPASS 6:DUPLEX 2/2 [ 1- 99]

50 50

Sim26-43 SIDE VOID

1:SIDE VOID(L) 2:SIDE VOID(R)

[ 0- 10]

Adjustment mode SIM Display

text

array

SPF image lead edge position

SIM 50-6

SIDE1 1 step:

(1st print surface)

Set value Spec value Set

range

0.1mm shift

Lead edge void: 1 - 4mm

1 - 99



Image loss: 3mm or less

d. Paper off center adjustment (SIM50-10)

1) Set a test chart (UKOG-0089CSZZ) on the document table.

2) Select a paper feed port and make a copy. Compare the copy and the test chart. If necessary, perform the following adjustment procedure.

3) Execute SIM 50-10. After completion of warm-up, shading is performed and the currently set off center adjustment value of each paper feed port is displayed.

c. Rear edge void adjustment (SIM50-1, SIM50-19)

1) Set a scale as shown in the figure below.

A4(8.5" x 11")

Paper rear edge

2) Set the document size to A4 (8.5" x 11"), and make a copy at 100%.

3) If necessary, perform the following adjustment procedure.

4) Execute SIM50-01 and select "DEN-B" with the arrow keys. The currently set adjustment value is displayed.

5) Enter the set value and press the start key. The correction value is stored and a copy is made.

Mode SIM Display

Rear edge void SIM

50-1

text array

DEN-B 1 step:

Set value Specifi-

cation

4mm or

0.1mm shift

less

Set

range

1 - 99

4) Enter the set value and press the start key. The correction value is stored and a copy is made.

Adjustment

mod Tr ay 1 SIM Tr ay 2 TRAY2 Tr ay 3 TRAY3 Tr ay 4 TRAY4

Manual paper

feed tray

Duplex

SIM Display

text array

TRAY1 Add 1:

50-10

BYPASS

DUPLEX

Set value Specifi-

cation

Single:

0.1mm shift to R side.

Center ±2.0mm

Reduce 1:

0.1mm shift to L side.

Set

range

1 - 99

(Second print

surface)

e. Side edge void area adjustment (SIM26-43)

Note:Before performing this adjustment, be sure to check that the paper

off center adjustment (SIM 50-10) is completed.

1) Set a test chart (UKOG-0089CSZZ) on the document table.

2) Select a paper feed port and make a copy. Compare the copy and the test chart. If necessary, perform the following adjustment procedure.

3) Execute SIM 26-43 and set the density mode to SIDE VOID (L), SIDE VOID (R).



The currently set adjustment value is displayed.

4) Enter the set value and press the start key. The correction value is stored.

Adjustment

mode

Side void (left) 26-43 SIDE

Side void (right) SIDE

MX-M182 ADJUSTMENT 6-4

SIM Display

text array

VOID (L)

VOID (R)

Set value Specifi-

cation

1 step:

0.5 - 4mm 1 - 99

0.5mm shift

Set

range

(2) Main scanning direction (FR direction) distortion

(1)

(2)

(4)

(3)

balance adjustment

1) Remove the OC glass and the right cabinet.

2) Loosen the copy lamp unit wire fixing screw.

4) Loosen the set screw of the scanner drive pulley which is not in contact with No. 2/3 mirror base unit positioning plate.

5) Without moving the scanner drive pulley shaft, manually turn the scanner drive pulley until the positioning plate is brought into contact with No. 2/3 mirror base unit, then fix the scanner drive pulley.

Wire fixing screw

3) Manually turn the mirror base drive pulley and bring No. 2/3 mirror base unit into contact with the positioning plate. At that time, if the front frame side and the rear frame side of No. 2/3 mirror base unit are brought into contact with the positioning plate at the same time, the mirror base unit parallelism is proper. If one of them is in contact with the positioning plate, perform the adjustment of 4).

6) Put No. 2/3 mirror base unit on the positioning plate again, push the projections on the front frame side and the rear frame side of the copy lamp unit to the corner frame, and tighten the wire fixing screw.

MX-M182 ADJUSTMENT 6-5

(3) Main scanning direction (FR direction) distortion

Rear side

Front side

When La < Lb

Turn the mirror base drive pulley on the front frame side in the arrow direction A. (Do not move the mirror base drive pulley shaft.)

When La > Lb

Turn the mirror base drive pulley on the rear frame side in the arrow direction A. (Do not move the mirror base drive pulley shaft.)

adjustment

This adjustment must be performed in the following cases:

• When the mirror base drive wire is replaced.

• When the lamp unit, or No. 2/3 mirror holder is replaced.

• When a copy as shown is made.

4) Loosen the mirror base drive pulley fixing screw on the front frame side or on the rear frame side.

Paper exit direction

Original

Copy

1) Set A3 (11" x 17") white paper on the original table as shown below.

Allow a little space.

Glass holding plate

Fit the paper edge and the glass holding plate edge.

A3 (11" x 17") white pape

2) Open the original cover and make a normal (100%) copy.

3) Measure the width of the black background at the lead edge and at the rear edge.

5) Tighten the mirror base drive pulley fixing screw.

La = Lb

6) Execute the main scanning direction (FR) distortion balance adjustment previously described in 2) again.

(4) Sub scanning direction (scanning direction) distortion

adjustment

When there is no skew copy in the mirror base scanning direction and there is no horizontal error (right angle to the scanning direction), the adjustment can be made by adjusting the No. 2/3 mirror base unit rail height. Before performing this adjustment, be sure to perform the horizontal image distortion adjustment in the laser scanner section. This adjustment must be performed in the following cases:

•When the mirror base wire is replaced.

•When the copy lamp unit or No. 2/3 mirror unit is replaced.

•When the mirror unit rail is replaced or moved.

•When a following copy is made.

Paper exit direction

La: Lead edge black background width Lb: Rear edge black background width

If the width (La) of the black background at the lead edge is equal that (Lb) at the rear edge, there is no need to execute the following procedures of 4) - 7).

Original

MX-M182 ADJUSTMENT 6-6

Copy A Copy B

1) Making of a test sheet 

When La > Lb Shift the mirror base B rail upward by the half of the difference of La - Lb.

When La < Lb Shift the mirror base B rail downward by the half of the difference of Lb - La. Example: When La = 12mm and Lb = 9mm, shift the mirror

base B rail upward by 1.5mm.

When Lc > Ld Shift the mirror base B rail downward by the half of the difference of Lc - Ld.

When Lc < Ld Shift the mirror base B rail downward by the half of the difference of Ld - Lc.

When moving the mirror base rail, hold the mirror base rail with your hand.

Sim48-1 COPY MAG.

1:F-R 2:SCAN

[ 1- 99]

Make test sheet by drawing parallel lines at 10mm from the both ends of A3 (11" x 17") white paper as shown below. (These lines must be correctly parallel to each other.)

Parallel line

10mm

White paper

2) Make a normal (100%) copy of the test sheet on A3 (11" x 17") paper. (Fit the paper edge with the glass holding plate edge.)

3) Measure the distances (La, Lb, Lc, Ld) at the four corners as shown below.

Paper exit direction

Lb Ld

When La = Lb and Lc = Ld, no need to perform the procedures 4) and 5).

4) Move the mirror base F rail position up and down (in the arrow direction) to adjust.

La = Lb, Lc = Ld

5) After completion of adjustment, manually turn the mirror base drive pulley, scan the mirror base A and mirror base B fully, and check that the mirror bases are not in contact with each other.

* If the mirror base rail is adjusted to extreme, the mirror base may

contact the frame or original glass. Be careful to avoid this.

(5) Main scanning direction (FR direction) magnification

ratio adjustment (SIM 48-1)

Note:Before performing this adjustment, be sure to check that the CCD

unit is properly installed.

1) Put a scale on the original table as shown below.

Note:Do not adjust the rail on the rear side.

If the rail on the rear side is adjusted, an error may occur. Only the rail on the front side can be adjusted.

2) Execute SIM 48-1.

3) After completion of warming up, shading is operated and the current correction value of the main scanning direction magnification ratio is displayed on the screen.

4) Enter the set values of the items of F and R, and press [START] key.  The correction values are saved and a copy is made.

MX-M182 ADJUSTMENT 6-7

Sim48-5 (R)SPF ZOOM

1:RSPF(SIDE1) 2:RSPF(SIDE2)

[ 1- 99]

Note: A judgment must be made with 200mm width, and must not be

made with 100mm width.

Adjustment mode SIM Display

text array

Main scanning direction magnifi

48-1 F-R +1

cation ratio

Set

value

+0.1%

-1

Specifications

Normal ±

1.0%

Set

range 1 - 99

0.1%

1) Put a scale on the original table as shown below, and make a normal (100%) copy to make a test chart.

(6) Sub scanning direction (scanning direction)

magnification ratio adjustment (SIM 48-1, SIM 48-5)

a. OC mode in copying (SIM48-1)

Note:Before performing this adjustment, be sure to check that the CCD

unit is properly installed.

1) Put a scale on the original table as shown below, and make a normal (100%) copy.

2) Compare the scale image and the actual image. If necessary, perform the following adjustment procedures.

3) Execute SIM 48-1.

4) After completion of warming up, shading is operated and the current correction value of the sub scanning direction magnification ratio is displayed on the screen.

Sim48-1 COPY MAG. 1:F-R

2:SCAN

[ 1- 99]

5) Select [2.SCAN] mode with the cross cursor.

Sim48-1 COPY MAG. 1:F-R

2:SCAN

[ 1- 99]

6) Enter the set value and press the start key. The set value is stored and a copy is made.

Adjustment mode SIM Display

text array

Sub scanning

48-1 SCAN +1 direction magnification ratio OC mode

b. RSPF sub scanning direction magnification ratio (SIM48-5)

Note:

•Before performing this adjustment, be sure to check that the CCD unit is properly installed.

•Before performing this adjustment, the OC mode adjustment in copying must be completed.

Set

value

+0.1%

-1

0.1%

Specifications

Normal ±

1.0%

Set

range 1 - 99

Note:Since the printed copy is used as a test chart, put the scale in

parallel with the edge lines.

2) Set the test chart on the SPF and make a normal (100%) copy.

3) Compare the scale image and the actual image. If necessary, perform the following adjustment procedures.

4) Execute SIM 48-5.

5) After warm-up, shading is performed.

6) Check to confirm that the RSPF (SIDE1) mode is selected with the cross cursor.

7) Enter the set value and press the start key. The set value is stored and a copy is made.

Adjustment mode SIM Display

text array

Sub scanning direction

48-5 RSPF

(SIDE1) magnification ratio

Set

value

+1 +0.1%

-1

0.1%

Specifications

Normal ±

1.0%

Set

range 1 - 99

(Front surface) Sub scanning

direction

RSPF

(SIDE2) magnification ratio (Back surface)

* "RSPF (SIDE2)" is displayed only when the RSPF is installed.

(7) Off center adjustment (SIM 50-12)

a. OC mode (SIM50-12)

1) Make a test chart as shown below and set it so that its center line is fit with the original guide center mark.

* To make a test chart, draw a line on A3 or 11" x 17" paper at the center

in the paper transport direction.

Original guide

Center

Copy paper (A3 or 17" x 11")

2) Make a normal copy from the manual paper feed tray, and compare the copy and the test chart. If necessary, perform the following adjustment procedures.

3) Execute SIM 50-12.



MX-M182 ADJUSTMENT 6-8

4) After completion of warming up, shading is performed and the current off-center adjustment value is displayed on the LCD.

Sim50-12

ORG. CENTER 1:OC 2:SPF(SIDE1) 3:SPF(SIDE2)

[ 1- 99]

50 50

5) Enter the set value and press the start key. The set value is stored and a copy is made.

C. Image density adjustment

(1) Copy mode (SIM 46-2)

1) Set a test chart (UKOG-0162FCZZ) on the OC table as shown below.

Adjustment

mode

Document off-

SIM Display

text array

50-12 OC +1 center (OC mode)

Set value Specifi-

cations

Center ±

Shifted to R

2.0% side by +0.mm.

-1 Shifted to L side by

0.1mm.

Set

range 1 - 99

UKOG-0162FCZZ

2) Put several sheets of A3 or 11" x 17" white paper on the test chart.

3) Execute SIM 46-2.

4) After completion of warming up, shading is performed, and the current density level is displayed on the LCD.

Sim46-1 EXP LEVEL 1:AE

2:TEXT 3:PHOTO 1 1/2 [ 1- 99]

50 50

Sim46-1 EXP LEVEL

4:PHOTO 2 5:TEXT(TS) 6:AE(TS) 2/2 [ 1- 99]

50 50

Use the cross cursor to select a mode.

5) Change the set value with the 10-key to adjust the copy image density.

6) Make a copy and check that the specification below is satisfied.

Density

Automatic

Te xt TEXT 3 "3" is slightly

Photo (Error diffu

Display

mode

text

array

Expo-

sure level

AE - "2" is slightly

PHOTO13 "2" is slightly

Sharp Gray

Chart output

copied.

Set value Set

The greater the set value is, the darker the density is. The smaller the set value is, the lighter the density is.

range

1 - 99

sion) Photo

(Dither) Toner

save

PHOTO23 "2" is slightly

copied.

TEXT (TS)

3 "3" is slightly

copied.

(Text) Toner

save (Auto

AE(TS) - "2" is slightly

copied.

matic)

MX-M182 ADJUSTMENT 6-9

[7] SIMULATIONS

1. Entering the simulation mode

Perform the following procedure to enter the simulation mode. [#] key [ ] key [C] key [ ] key Main code [START] key Sub code [START] key

2. Canceling the simulation mode

When the [CA] key is pressed, the simulation mode is cancelled. When the interruption key is pressed, the process is interrupted and the screen returns to the sub code entering display. * After canceling the simulation mode, be sure to turn OFF/ON the

power and check the operation.

Note: If the machine is terminated by a jam error or paper empty during

copying in the adjustment by the simulation, recopying is required.

Note: The values in the simulation columns are not default values but

sample values.

3. List of simulations

Main

Sub

code

01 01 Mirror scanning operation

02 Mirror home position sensor (MHPS) status display

02 01 Single paper feeder (SPF)/Reversing single pass

03 02 Shifter/job separator sensor status display

05 01 Operation panel display check

06 01 Paper feed/transport solenoid operation check

07 01 Warm-up display and aging with jam detection

08 01 Developing bias output

09 01 Duplex motor forward rotation check *6

10 - Toner motor operation 14 - Trouble cancel (except for U2) 16 - U2 trouble cancel 20 01 Maintenance counter clear 21 01 Maintenance cycle setting

feeder(RSPF) aging *2 02 SPF/RSPF sensor status display *2 03 SPF/RSPF motor operation check *2 08 SPF/RSPF paper feed solenoid operation check *2 09 RSPF reverse solenoid operation check *2 *3 11 SPF/RSPF PS release solenoid operation check *2

03 Shifter operation check 04 Job separator operation check *4 11 Shifter home position check

02 Fusing lamp and cooling fan operation check 03 Copy lamp lighting check

02 Resist roller solenoid (RRS) operation check

06 Intermittent aging 08 Shifting with warm-up display

02 Main charger output (Grid = HIGH) 03 Main charger output (Grid = LOW) 06 Transfer charger output

02 Duplex motor reverse rotation check *6 04 Duplex motor RPM adjustment *6 05 Duplex motor switchback time adjustment

Contents

Main

Sub

code

22 01 Counters display

03 Jam memory display 04 Jam total counter display 07 System setting code display 09 Paper feed counter display 11 FAX-related counter display 13 CRUM destination display *5 14 P-ROM version display 15 Trouble memory display 22 SPF/RSPF jam counter display *2

24 01 Jam total counter clear

02 Trouble memory clear 04 SPF/RSPF counter clear *2 05 Duplex print counter clear *6 06 Paper feed counter clear 07 Drum counter clear 08 Copy counter clear 09 Printer counter clear 10 FAX-related counter clear 13 Scanner counter clear 14 SPF/RSPF jam total counter clear *2 15 Scanner mode counter clear

25 01 Main motor operation check (Cooling fan motor rotation

26 01 Job separator setting

30 01 Paper sensor status display 41 01 Document size detection photo sensor check

42 01 Developing counter clear

check)

02 Auto developer adjustment (Initial setting of toner

density when replacing developer)

10 Polygon motor operation check

02 Size setting 03 Auditor setting 04 Copier duplex setting 05 Count mode setting 06 Destination setting 07 Machine condition check 08 Manual transfer shaking countermeasures setting 18 Toner save mode setting 20 Job separator paper exit mode setting 22 Language setting clear 30 CE mark conformity control ON/OFF 31 Auditor mode exclusive setup 36 Cancel of stop at maintenance life over 37 Cancel of stop at developer life over 39 Memory capacity check 42 Transfer ON/OFF timing control setting 43 Side void amount setting 51 Copy temporary stop function setting 54 LCD contrast PWM duty setting 56 Life correction ON/OFF setting 60 [FAX] key Enable/Disable setting 69 Toner near end environment setting 73 Toner save setting display/non-display 74 Total counter display change setting

02 Document size detection photo sensor detection level

adjustment

03 Document size detection photo sensor light receiving/

detection level check

04 Detection level adjustment when the document size is

settled(15degrees - 20degrees)

Contents

MX-M182 SIMULATIONS 7-1

Main

Sub

code

43 01 Fusing temperature setting 1

02 Fusing temperature setting 2 03 Fusing temperature setting 3 04 Fusing temperature setting 4 12 Standby mode fusing fan rotation setting 13 Paper interval control allow/inhibit setting

44 01 Enable/Disable setting of toner density control

correction 16 Toner density control data check and toner density

correction quantity display 34 Transfer current setting

46 02 Copy density adjustment (600dpi)

10 Copy exposure level adjustment, individual setting

(Text) 600dpi 11 Copy exposure level adjustment, individual setting

(Photo) 600dpi 12 Density adjustment in the FAX mode 

(Collective adjustments)

13-16 Density adjustment in the FAX mode 

(Individual adjustments) 19 Exposure mode setting

(Gamma table setting/AE operation mode setting/

Photo image process setting) 20 SPF/RSPF exposure correction *2 29 Image contrast adjustment (600dpi) 30 AE limit setting 31 Image sharpness adjustment 39 FAX IMAGE adjustment

48 01 Main/sub scanning magnification ratio adjustment

05 SPF/RSPF mode sub scanning magnification ratio

adjustment in copying *2 08 FAX magnification ratio adjustment (scan) 09 FAX magnification ratio adjustment (print)

49 01 Flash ROM program writing mode (MCU)

02 Flash ROM program writing mode (NNB)

50 01 Image lead edge adjustment

06 Copy lead edge position adjustment (SPF/RSPF) *2

8 FAX lead edge adjustment (scan) 10 Print off-center adjustment 12 Document off-center adjustment 18 Memory reverse position adjustment in duplex copy *1 19 Rear edge void adjustment in duplex copy *5

51 02 Resist amount adjustment 53 08 SPF/RSPF scanning position automatic adjustment *2 61 02 Laser power correction ON/OFF (Invalidity)

03 HSYNC output check

63 01 Shading check 64 01 Self print 65 10 Key ACK time setting display/non-display setting

11 Info lamp setting

Contents

Main

Sub

code

66 01 FAX soft SW setting

02 FAX soft SW initializing 03 FAX PWB memory check 04 Signal send mode 06 Confidential pass code print 07 Image memory content output 10 Image memory contents clear 11 300bps signal send 13 Dial number registration 17 DTMF signal send 21 FAX information print 24 FAST SRAM clear 30 TEL/LIU status change check 31 TEL/LIU setting 32 Receive data check 33 Signal detection check 34 Communication time measurement 37 Speaker sound volume adjustment 38 Time setting/check 42 PC program writing 43 PIC adjustment value writing 52 Pseudo ringer check

67 50 USB reception speed adjustment

<Execution inhibit conditions> *1) Execution is inhibited when the duplex setup is OFF and other than

RSPF is set. *2) Execution is inhibited when OC. *3) Execution is inhibited when SPF. (Not RSPF) *4) Execution is inhibited when the job separator is not installed. *5) Execution is inhibited when the model is not provided with the

CRUM. *6) Execution is inhibited when the duplex setup is OFF.

Contents

MX-M182 SIMULATIONS 7-2

4. Contents of simulations

Main code

01 01 Mirror scanning operation

Sub

code

Used to check the operations of the scanner unit and its control circuit. Enter the number of times and the magnification ratio, and press [OK] key to operate the scanner unit. The speed is variable according to the specified magnification ratio. The number of scanning can be specified by entering a value to the right lower section of the LCD.

•Setting range of magnification ratio: 25%-400%

•Setting range of the number of scanning: 0-999 (When 0 is set, it means unlimited. )

(Scan number input window)

Sim1-1 SCAN CHECK

115 %

100%

86%

ZOOM 100% 5

(Execution window)

Sim1-1 SCAN CHECK

115 %

100%

86%

ZOOM 100% EXEC

MHPS

[OK] key or [START] Key

MHPS

123

Contents Remark

Set the scan magnification ration. This magnification ratio accords with the scan speed in actual copying. The setting range is 25% - 400%.

Specify the scan number to be performed. The setting range is 0 - 999. When 0 is set, the number is unlimited.

MHPS sensor status

Scan counter

Highlighted during execution

Used to display the status (ON/OFF) of the mirror HP sensor on the LCD during scanning. (Highlighted at ON) "EXEC" is displayed to indicate execution is in process. The scan counter is displayed above "EXEC." This counter is counted up even in simulation. The copy lamp is lighted during scanning.

[CA] key: Exits the simulation mode. [INTERRUPT] key: Returns to the sub code input window. [C] key: Input value clear Numeric keys: Input of the number of scanning

02 Mirror home positions sensor (MHPS) status display

Used to monitor the mirror home position sensor and display the ON/OF status of the sensor on the LCD.

Sim1-2 SENSOR CHECK

MHPS

MHPS(MIRROR HOME POSITION SENSOR) ON :Highlight display OFF :Normal display

[CA] key: Exits the simulation mode. [INTERRUPT] key: Returns to the sub code input window.

MX-M182 SIMULATIONS 7-3

Main

code

Sub

code

Contents Remark

02 01 Single Paper Feeder(SPF)/Reversing single pass feeder(RSPF)aging

Used to check the operations of the SPF/RSPF unit and its control circuit. Enter the magnification ratio and press[OK] key or [START] key to drive the SPF/RSPF unit at the speed corresponding to the setting.

(Magnification ratio selection window)

Sim2-1 SPF AGING 115 %

100%

86%

ZOOM 100% EXEC

(Execution window)

Sim2-1 SPF AGING 115 %

100%

86%

ZOOM 100% EXEC

1SIDE

2SIDE

[OK] key or [START] Key

1SIDE

2SIDE

Select the scan magnification ratio (drive speed). This also accords with the magnification ratio and the speed in copying similarly to the OC. The setting range is 50% - 200%.

"EXEC" is highlighted during execution.

* When [INTERRUPT] key is press, the simulation is terminated and the machine returns to the sub code

input window.

* When [CA] key is pressed, the simulation is terminated and the machine exits the simulation mode.

02 SPF/RSPF sensor status display

Used to display the sensor status in the SPF/RSPF section. An active sensor is highlighted.

Sim2-2 SENSOR CHECK

SPFP OCCV POUT SPFC

L1 L2

W2 W3

Displayed name : Sensor name SPFP :SPF document transportation sensor OCCV :SPF unit (OC cover) open/close sensor POUT :SPF paper exit sensor SPFC :SPF paper feed cover open/close senso L1 :SPF paper length sensor 1 L2 :SPF paper length sensor 2 W0 :SPF document set sensor W1 :SPF paper width sensor (small) W2 :SPF paper width sensor (middle) W3 :SPF paper width sensor (large)

[CA] key: Exits the simulation mode. [INTERRUPT] key: Returns to the sub code input window.

03 SPF/RSPF motor operation check

Used to check the operation of the SPF/RSPF motor and its control circuit. When this simulation is executed, the initial menu shown below is displayed. Select the magnification ratio to drive the motor.

(Initial window = Magnification ratio selection window)

Sim2-3 OUTPUT CHECK

115 %

100%

86%

ZOOM 100% EXEC

Select the scan magnification ratio (drive speed). This also accords with the magnification ratio and the speed in copying. The setting range is 50% - 200%.

Only when the SPF/ RSPF is installed.

[OK] key or [START] Key

(Execution window)

Sim2-3 OUTPUT CHECK

115 %

100%

86%

ZOOM 100% EXEC

"EXEC" is highlighted during execution.

[CA] key: The SPF/RSPF motor is stopped, and the machine exits the simulation mode. [INTERRUPT] key: The SPF/RSPF motor is stopped, and the machine returns to the sub code input window.

MX-M182 SIMULATIONS 7-4

Main

code

Sub

code

02 08 SPF/RSPF paper feed solenoid operation check

Used to drive the SPF/RSPF paper feed solenoid (PSOL) 20 times in the cycle of 500msec of "ON" and 500msec of "OFF." After completion of the process, the machine returns to the sub code input window.

(Initial window) (Execution window)

Sim2-8 SPUS CHECK

[OK] key or [START] Key

Contents Remark

(Only when the SPF/RSPF is installed.}

Sim2-8 SPUS CHECK

PRESS OK KEY EXEC

When [INTERRUPT] key is pressed, the machine returns to the sub code input window. When [CA] key is pressed, the machine exits the simulation mode.

09 RSPF reverse solenoid operation check

Used to drive the RSPF reverse solenoid (RSOL) 20 times in the cycle of 500msec of "ON" and 500msec of "OFF." After completion of the process, the machine returns to the sub code input window.

(Initial window) (Execution window)

Sim2-9 SPFS CHECK

PRESS OK KEY EXEC

[OK] key or [START] Key

When [INTERRUPT] key is pressed, the machine returns to the sub code input window. When [CA] key is pressed, the machine exits the simulation mode.

11 SPF/RSPF PS release solenoid operation check

Used to drive the SPF/RSPF PS release solenoid (CLH) 20 times in the cycle of 500msec of "ON" and 500msec of "OFF." After completion of the process, the machine returns to the sub code input window.

(Initial window) (Execution window)

Sim2-11 CLH CHECK

PRESS OK KEY EXEC

[OK] key or [START] Key

When [INTERRUPT] key is pressed, the machine returns to the sub code input window. When [CA] key is pressed, the machine exits the simulation mode.

03 02 Shifter/job separator sensor status display

Used to monitor the sensors related to the shifter and the job separator and display the sensor status on the LCD. An active sensor is highlighted.

Sim3-2 SENSOR

SFTHP TRYF

JSUP

TRYD

JSDL

Displayed name :Sensor name SFTHP :Shifter home position sensor JSUP :Job separator upper limit senso JSDL :Job separator lower limit sensor TRYF :Tray full sensor TRYD : Paper exit sensor

* Displayed only when the job separator is installed except for SFTH.

EXEC

(Only when the RSPF is installed.)

Sim2-9 SPFS CHECK

EXEC

(Only when the SPF/RSPF is installed.)

Sim2-11 CLH CHECK

EXEC

(Sensor of shifter is Japan only) (Only when the job separator is installed.)

MX-M182 SIMULATIONS 7-5

Main

code

Sub

code

03 03 Shifter operation check

Used to reciprocate the shifter 4 times. During execution, the status of the shifter HP sensor is displayed on the right upper section of the screen. (When the sensor is detected, the display is highlighted.)

[CA] key: Exits the simulation mode. [INTERRUPT] key: Returns to the sub code input window. * When the above [CA] key or [INTERRUPT] key is pressed during operation of the shifter, the shifter is

returned to the home position before terminating the operations.

(Initial window) (Execution window)

Sim3-3 SHIFTER CHK

[OK] key or [START] Key

Contents Remark

Japan only

Sim3-3 SHIFTER CHK

SFTHP

PRESS OK KEY EXEC

EXEC

04 Job separator operation check

Used to operate the job separator up and down for 30sec. During operation, the status of the upper limit sensor and the lower limit sensor is displayed on the right upper section of the display.

[CA] key: Exits the simulation mode. [INTERRUPT] key: Returns to the sub code input window. When the operation is interrupted, the job separator is shifted to the home position before terminating the simulation similarly to the shifter.

(Initial window) (Execution window)

Sim3-4 JOBSEPA CHK

PRESS OK KEY EXEC

[OK] key or [START] Key

Sim3-4 JOBSEPA CHK

JSUP

JSDL

EXEC

Display

name

JSUP Job separator

JSDL Job separator

Sensor

upper limit senso

lower limit sensor

11 Shifter home position check

Used to check the operations of the shifter HP sensor and the shifter. When this simulation is executed, the initial menu is displayed. By the following key operations, the left operation and the right operation of the home position sensor and the shifter can be executed separately.

[ ] key: Shifts to R side by the specified steps. [ ] key: Shifts to F side by the specified steps. [ ] key: Shift to the home position. [SFTHP] is highlighted when the HP sensor is detected.

(Initial window)

Sim3-11 SHIFTER CHK SFTHP

(Only when the job separator is installed.)

name

Japan only

[ ]:R [ ]:HP [ ]:F

[CA] key: Exits the simulation mode. [INTERRUPT] key: Returns to the sub code input window.

MX-M182 SIMULATIONS 7-6

Main code

Sub

code

05 01 Operation panel display check

<LED/LCD check mode> Used to check the operations (ON, display) of the LED and the LCD on the operation panel. When this simulation is executed, all LED's on the operation panel (including 7SEG) are lighted and checking LCD is started. For the operation check of LCD, the area is divided into two sections; upper section and lower section, and the display cycle of Normal 2sec.

Contents Remark

Dark Light Off is repeated in each section. Each display period is

Normal

Sim5-1 LCD/LED CHK.

Normal

Sim5-1 LCD/LED CHK.

Off

Sim5-1 LCD/LED CHK.

Dark

Sim5-1 LCD/LED CHK.

Dark

Sim5-1 LCD/LED CHK.

Sub code input standby window

Light

Sim5-1 LCD/LED CHK.

Light

Sim5-1 LCD/LED CHK.

When [INTERRUPT] key is pressed in the LED check mode, the machine returns to the sub code input window. When [CA] key is pressed, the machine exits the simulation mode. When [START] key is pressed during LCD display, the machine goes to the key input check mode.

<Key input check mode> Used to check that the keys on the operation panel are properly detected. When the machine enters the key input check mode, the initial menu is displayed.

(Initial window)

Sim5-1 LCD/LED CHK.

When any key is pressed, the value on the right lower side is counted up. If a key is pressed once, it is not counted again. When [CA] key is pressed for the first time, it is counted. When it is pressed for the second time, the simulation mode is terminated. When [INTERRUPT] key is pressed for the first time, it is counted. When it is pressed for the second time, the window returns to the sub code input standby window. * Note for the key input check mode

[START] key must be pressed at the end. If it is pressed midway, the simulation judges that the last key is pressed and terminates the check mode. Multi input of tow or more keys is ignored.

MX-M182 SIMULATIONS 7-7

Main code

Sub

code

05 02 Fusing lamp and cooling fan operation check

Used to check the operations of the heater lamp and the cooling fan and the peripheral circuits. When this simulation is executed, the following initial menu is displayed.

(Initial window) (Execution window)

Sim5-2 HT LAMP

[OK] key or [START] Key

Contents Remark

Sim5-2 HT LAMP

PRESS OK KEY EXEC

When this simulation is executed, the fusing lamp repeats ON/OFF 5 times in the cycle of 500ms. The cooling fan motor is rotated during that period. (The cooling fan, however, is rotated for about 8sec.) After completion of the operation, the machine returns to the sub code input window.

03 Copy lamp lighting check

Used to check the operations of the copy lamp and its peripheral circuit. When this simulation is executed, the following initial menu is displayed.

(Initial window) (Execution window)

Sim5-3 COPY LAMP

PRESS OK KEY EXEC

[OK] key or [START] Key

When [OK] key or [START] key is pressed, the copy lamp is lighted for about 5sec. After passing for 5sec, the machine returns to the sub code input window.

06 01 Paper feed/transport solenoid operation check

When this simulation is executed, the names of the solenoids which can be operated are displayed. Select a load to be operated with the numeric keys.

(Load selection window)

Sim6-1 OUTPUT CHECK

1:CPSOL 2:PSOL1 3:PSOL2

(Load selection window)

Sim6-1 OUTPUT CHECK

1:CPSOL 2:PSOL1 3:PSOL2

4:PSOL3 5:HPSOL 6:FSOL2

EXEC1/2 1

Numeric keys

4:PSOL3 5:HPSOL 6:FSOL2

EXEC1/2 2

1: CPSOL :Cassette 1 paper feed solenoid 2: PSOL1 :Cassette 2 paper feed solenoid (*) 3: PSOL2 :Cassette 2 paper feed solenoid (*) 4: PSOL3 :Cassette 3 paper feed solenoid (*) 5: HPSOL :Manual feed tray paper feed solenoid 6: FSOL2 :Cassette 2 transport solenoid (*) 7: FSOL3 :Cassette 3 transport solenoid (*) (*) Supported only for the model with the option installed. Skipped for the other models without installation.

After completion of execution

EXEC

Sim5-3 COPY LAMP

EXEC

[OK] key or [START] Key

(Execution window)

Sim6-1 OUTPUT CHECK

1:CPSOL 2:PSOL1 3:PSOL2

4:PSOL3 5:HPSOL 6:FSOL2

EXEC1/2 2

During execution, the selected solenoid repeats ON/OFF 20 times for every 500ms.

02 Resist roller solenoid (RRS) operation check

When this simulation is executed, the machine goes to the execution start window. When [OK] key or [START] key is pressed, the resist roller solenoid (RRS) repeats ON of 500ms and OFF of 500ms 20 times.

(Execution start window) (Execution window)

Sim6-2 RRS CHECK

PRESS OK KEY EXEC

[OK] key or [START] Key

Sim6-2 RRS CHECK

EXEC

When the operation is completed, the machine returns to the sub code input window. When [INTERRUPT] key is pressed, the machine returns to the sub code input window. When [CA] key is pressed, the machine exits the simulation mode.

MX-M182 SIMULATIONS 7-8

Main code

Sub

code

07 01 Warm-up display and aging with jam detection

Used to measure the warm-up time and execute aging with jam detection. When this simulation is executed, the following warm-up window is displayed. The time required for starting the warm-up and completing the initializing operation and shifting to the standby state is displayed. After completion of warm-up, press [CA] key to exit the simulation mode, allowing normal copy operations. The copy mode at that time is the aging mode with 0sec of intermittent aging.

(Warming up window)

Sim7-1 W-UP C-MODE

WARMING UP.

(Warming up completion window)

Sim7-1 W-UP C-MODE

WARM UP COMPLETED.

Contents Remark

(Copy window)

[CA] key

Ready to copy.

100%

8 1/2×11

Canceled by turning off the power or executing a simulation which makes the hardware reset. When the interruption is pressed to shift to the input standby window, the machine does not enter the aging mode.

06 Intermittent aging

Used to execute intermittent aging of 3sec. The set quantity and the mode are optionally selected. When this simulation is executed, the following execution start window is displayed. When [OK] key or [START] key is pressed, the machine exits the simulation mode. Enter a desired coy mode and a desired copy quantity. Press [START] key, and intermittent aging will be started.

(Execution start window)

Sim7-6 INTERVAL SET AGING INTERVAL

AER YOU SURE? EXEC

(Copy window)

Ready to copy.

100%

8 1/2×11

It is canceled by turning off the power or executing a simulation with the hard reset.

08 Shifting with warm-up display

Used to measure the warm-up time. When this simulation is executed, the following warm-up window is displayed. The time required for starting the warm-up and completing the initializing operation and shifting to the standby state is displayed. * Though [CA] key is pressed, the machine does not enter the aging mode of intermission 0 sec.

(Warming up window)

Sim7-8 W-UP C-MODE WARMING UP.

(Warming up completion window)

Sim7-8 W-UP C-MODE

WARM UP COMPLETED.

Press [CA] key to exit the simulation mode. (The aging function is omitted from SIM 07-01.) Note: Toner supply operation is not performed during this simulation.

08 01 Developing bias output

Used to check the developing bias output. When this simulation is executed, the following execution start window is displayed. When [OK] key or [START] key is pressed, the developing bias signal is turned ON for 30sec. When measuring the actual output value, however, use SIM 25-01. After completion of the process, the machine returns to the sub code input window.

(Execution start window) (Execution window)

Sim8-1 DV BIAS

PRESS OK KEY EXEC

[CA] key: Exits the simulation mode. [INTERRUPT] key: Interrupts output operation and shifts to the sib code input window.

[OK] key or [START] Key

Sim8-1 DV BIAS

EXEC

MX-M182 SIMULATIONS 7-9

Main

Window display Output mode 1:NML_A Normal size width (front) 2:NML_B Normal size width (back) 3:SML_A Small size width (front) 4:SML_B Small size width (back)

code

Sub

code

08 02 Main charger output (Grid = HIGH)

Used to check the main charger output. When this simulation is executed, the following execution start window is displayed. When [OK] key or [START] key is pressed, the main charger is turned on for 30 sec in the grid voltage HIGH mode. After completion of the process, the machine returns to the sub code input window.

(Execution start window) (Execution window)

Sim8-2 MHV(H)

[OK] key or [START] Key

Contents Remark

Sim8-2 MHV(H)

PRESS OK KEY EXEC

EXEC

[CA] key: Exits the simulation mode. [INTERRUPT] key: Interrupts output operation and shifts to the sub code input window.

03 Main charger output (Grid = LOW)

Used to check the main charger output. When this simulation is executed, the following execution start window is displayed. When [OK] key or [START] key is pressed, the main charger is turned on for 30 sec in the grid voltage LOW mode. After completion of the process, the machine returns to the sub code input window.

(Execution start window) (Execution window)

Sim8-3 MHV(L)

PRESS OK KEY EXEC

[OK] key or [START] Key

Sim8-3 MHV(L)

EXEC

[CA] key: Exits the simulation mode. [INTERRUPT] key: Interrupts output operation and shifts to the sub code input window.

06 Transfer charger output

When this simulation is executed, the machine shifts to the following mode select window, and the list of the modes to be outputted is displayed. Select an output mode with numeric keys and press [OK] key or [START] key, and the transfer charger output is made for about 30sec in the specified mode.

(Mode selection window)

Sim8-6 TC OUTPUT 1:NML_A

2:NML_B 3:SML_A

4:SML_B 5:BYPASS

EXEC

[OK] key or [START] Key

(Execution window)

Sim8-6 TC OUTPUT 1:NML_A

2:NML_B 3:SML_A

4:SML_B 5:BYPASS

EXEC

* The items of (back) is not displayed when DUPLEX setting is OFF. * Small size paper is Letter R (A4R) width or below. When an output is completed, the machine shifts to

the mode select window. [CA] key: Exits the simulation mode. [INTERRUPT] key: Interrupts the output operation, and shifts to the sub code input window.

MX-M182 SIMULATIONS 7-10

Main code

Sub

code

09 01 Duplex motor forward rotation check

Used to check the duplex motor rotation. The duplex motor is rotated in the normal direction (paper exit direction) for 30sec. After completion of the process, the machine shifts to the sub code input window.

(Execution start window) (Execution window)

Sim9-1 DMF CHECK

[OK] key or [START] Key

Contents Remark

(Execution is not allowed when DUPLEX setting is OFF.)

Sim9-1 DMF CHECK

PRESS OK KEY EXEC

EXEC

[CA] key: Exits the simulation mode. [INTERRUPT] key: Interrupts the output operation, and shifts to the sub code input window.

02 Duplex motor reverse rotation check

Used to check the duplex motor reverse rotation. The duplex motor is rotated in the reverse direction for 30sec. After completion of the process, the machine shifts to the sub code input window.

(Execution start window) (Execution window)

Sim9-2 DMR CHECK

PRESS OK KEY EXEC

[OK] key or [START] Key

Sim9-2 DMR CHECK

EXEC

[CA] key: Exits the simulation mode. [INTERRUPT] key: Interrupts the output operation, and shifts to the sub code input window.

04 Duplex motor RPM adjustment

Used to adjust the duplex motor rotation speed. When this simulation is executed, the following setting window is displayed. Enter an input value with numeric keys and press [OK] key or [START] key. The setting range is in 1-13 steps.

(Setting window)

Sim9-4 MOTOR SPEED

1:MOTOR SPEED

• 18cpm/20cpm machine: Set value : Speed (PPS) 01 : 637.2PPS (Slow)

02 : 640.4PPS 03 : 643.6PPS 04 : 646.9PPS

4[ 1-13]

05 : 650.1PPS 06 : 653.3PPS 07 : 656.5PPS 08 : 659.8PPS 09 : 662.9PPS 10 : 666.2PPS 11 : 669.4PPS 12 : 672.6PPS

• 23cpm machine: Set value : Speed (PPS) 01 : 760.2PPS (Slow) 02 : 764.1PPS 03 : 768.0PPS 04 : 771.8PPS 05 : 775.7PPS 06 : 779.5PPS 07 : 783.3PPS 08 : 787.2PPS 09 : 791.0PPS 10 : 794.8PPS 11 : 798.6PPS 12 : 802.5PPS

When a value outside the setting range is inputted, it is ignored. [CA] key: Exits the simulation mode. [INTERRUPT] key: Shift to the sub code input window.

05 Duplex motor switchback time adjustment

Used to adjust the duplex motor switchback time when the motor reverse rotation is controlled. When this simulation is executed, the following setting window is displayed. Enter an input value with numeric keys and press [OK] key or [START] key. The setting range is 50-76. When the adjustment value is increased by 1, the distance up to reverse start is increased by 3 steps in 1-2 phase excitement.

Sim9-5 SW BACK TIME

1:SW BACK TIME

(Execution is not allowed when DUPLEX setting is OFF.)

Default: 4

Default: 50

50[ 50-76]

When a value outside the setting range is inputted, it is ignored. [CA] key: Exits the simulation mode. [INTERRUPT] key: Shift to the sub code input window.

MX-M182 SIMULATIONS 7-11

Main code

Sub

code

10 - Toner motor operation

Used to check the operation of the toner motor. When this simulation is executed, the following execution start window is displayed. Press [OK] key or [START] key, and the toner motor is rotated for about 30sec. After completion of the process, the machine shifts to the sub code input window.

(Execution start window) (Execution window)

Sim10 TONER MOTOR

[OK] key or [START] Key

Contents Remark

Sim10 TONER MOTOR

PRESS OK KEY EXEC

[CA] key: Exits the simulation mode. [INTERRUPT] key: Interrupts the output operation, and shifts to the sub code input window.

14 - Trouble cancel (except for U2)

* Used to cancel EEPROM writing troubles such as H trouble and execute the hard reset. When this simulation is executed, the following execution start window is displayed. Press [OK] key or [START] key to clear the trouble other than U2.

(Execution start window)

Sim14 TROUBLE CLEAR

TROUBLE CLEAR (WITHOUT U2)

AER YOU SURE? EXEC

16 - U2 trouble cancel

* Used to cancel the U2 trouble and execute the hard reset. When this simulation is executed, the following execution start window is displayed. Press [OK] key or

[START] key to clear the U2 trouble.

(Execution start window)

Sim16 TROUBLE CLEAR

U2 TROUBLE CLEAR

AER YOU SURE? EXEC

20 01 Maintenance counter clear

EXEC

Used to clear the maintenance counter. Press [OK] key or [START] key on the following window, the maintenance counter is cleared and the machine returns to the sub code input window.

Sim20-1 COUNTER CLR MAINTENANCE COUNTER CLEAR

AER YOU SURE? EXEC

21 01 Maintenance cycle setting

Used to set the maintenance cycle. When this simulation is executed, the current set value is displayed. Enter a desired code with numeric keys and press [START] key. The set value is saved in the EEPROM and the machine returns to the sub code input window.

Sim21-1 CYCLE SET.

1:MAINTE CYCLE

4[ 0- 5]

[CA] key: Exits the simulation mode. [INTERRUPT] key: Returns to the sub code input window.

Default: 4

0: 5K (5,000 sheets) 1: 7.5K (7,500 sheets) 2: 10K (10,000 sheets) 3: 25K (25,000 sheets) 4: 50K (50,000 sheets) 5: FREE (999,999 sheets) (Setting range: 0 - 5)

MX-M182 SIMULATIONS 7-12

Main code

Sub

code

22 01 Counters display

Sim22-1 COUNTER 1/4

TOTAL :nnnnnnn MAINTE :nnnnnnn DEV :nnnnnnn(*) DRUM :nnnnnnn

key key

Sim22-1 COUNTER 2/4

CPY JOB : nnnnnnn PRT JOB : nnnnnnn SCN JOB : nnnnnnn OC SCN : nnnnnnn

key key

Sim22-1 COUNTER 3/4

SPF : nnnnnnn DUPLEX : nnnnnnn OTHERS : nnnnnnn MNTCYC : nnnnnnn

key key

Sim22-1 COUNTER 4/4

DEV TTL : nnnnnnn DRM TTL : nnnnnnn

Contents Remark

Counter display TOTAL : Total counter MAINTE : Maintenance counter DEV : Development counter DRUM : Drum counter CPY JOB : Copy job counter PRT JOB : Print job counter SCN JOB : Scan job counter OC SCN : OC scan counter SPF : SPF/RSPF counter DUPLEX : DUPLEX counter OTHERS : Other counter MNTCYC : Maintenance cycle DEV TTL : Development rotation accumulated time DRM TTL : Drum rotation accumulated time

Though SIM26-74 is set to "1: Scan counter is added," the count is not added to SIM22-01 total counter display. The setting affects only the total counter display in the system settings.

03 Jam memory display

Used to check the jam kind occurred in the main unit and the SPF/RSPF. The kinds of jams up to 30 items are displayed sequentially from the latest one. (The oldest one is deleted sequentially.) This display is used for troubleshooting. (If there are extremely many troubles in a position, it may be judged that a repair must be executed.) The kinds and contents of jams to be displayed are as follows.

Sim22-3 JAM HIS. 1/4

XXXXXXX XXXXXXX XXXXXXX XXXXXXX XXXXXXX XXXXXXX XXXXXXX XXXXXXX

key key

Sim22-3 JAM HIS. 2/4

XXXXXXX XXXXXXX XXXXXXX XXXXXXX XXXXXXX XXXXXXX XXXXXXX XXXXXXX

Kinds of jams and display contents SPPD_ON : SPF paper entry sensor (Not reached) SPPD_OFF : SPF paper entry sensor (Remaining) SOUT_ON : SPF paper exit sensor (Not reached) SOUT_OFF : SPF paper exit sensor (Remaining) POUT_ON : Paper exit sensor (Not reached) POUT_OFF : Paper exit sensor (Remaining) DPX_ON : DUP sensor (Not reached) DPX_OFF : DUP sensor (Remaining) PIN_ON : Paper feed sensor (Not reached) PIN_OFF : Paper feed sensor (Remaining) PIN2_ON : Cassette 2 paper feed sensor (Not reached) PIN3_ON : Cassette 3 paper feed sensor (Not reached) PIN4_ON : Cassette 4 paper feed sensor (Not reached)

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

key, key: Switches to another page.

04 Jam total counter display

Used to display the jam total counter.

Sim22-4 COUNTER

JAM : nnnnnn

MX-M182 SIMULATIONS 7-13

Main

Sim22-11 FAX COUN. COMM. PAGE

SND xx, xxx, xxx RCV xx, xxx, xxx

Sim22-11 FAX COUN. SELECT COUNTER

3:PRINT PAGE

(1 - 3)

Sim22-11 FAX COUN. COMM. TIME

SND:hhhhhhhh:mm:ss RCV:hhhhhhhh:mm:ss

Sim22-11 FAX COUN. SELECT COUNTER

1:COMM. PAGE 2:COMM. TIME (1 - 3)

Sim22-11 FAX COUN. PRINT PAGE

xxxxxxxx

[1] key

[OK] key [OK] key [OK] key

[2] key [3] key

Return Return

[CA] key

: Simulation cancel

[INTERRUPT] key

: Sub code input window

code

Sub

code

22 07 System setting code display

Used to display the system setting code.

Sim22-7 SYSTEM

SYS CODE: nnnnn

09 Paper feed counter display

Used to display the paper feed quantity of each paper feed tray. This simulation shows the use frequency of each paper feed section.

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

key, key: Switches to another page.

Sim22-9 COUNTER 1/2

BYPASS : nnnnnnn TRAY1 : nnnnnnn TRAY2 : nnnnnnn TRAY3 : nnnnnnn

* TRAY2-TRAY4 are displayed only when they are installed.

11 FAX-related counter display.

key

Contents Remark

Sim22-9 COUNTER 2/2

TRAY4 : nnnnnnn

Used to display the current FAX send/receive counter value.

13 CRUM destination display

Used to display the CRUM chip destination code saved in the EEPROM. If the display does not match the destination code saved in the CRUM chip, it is judged as an error. * This simulation is valid only for the model with the CRUM chip.

Sim22-13 CRUM

CRUM TYPE nn

Number : Setting (Destination) 00 : Not set. 01 : Destination-A (North America) 02 : Destination-B (Europe) 03 : Destination-C (SMEF) 04 : CHN-A

14 P-ROM version display

Sim22-14 ROM VER1/2

S/N : -----------

05 : JPN-A

Sim22-14 ROM VER2/2

FAX : --.-MCU : --.-NNB : --.-PNL : --.--

The version of the option board which is not installed is not displayed.

Number : Setting (Destination) 06 : Destination-X (Iran) 99 : Conversion

S/N :Production serial number MCU :Main unit program version NNB :NNB program version PNL :Panel program version FAX :FAX program version

MX-M182 SIMULATIONS 7-14

Main code

Sub

code

22 15 Trouble memory display

The latest 20 troubles are displayed. (The oldest one is overwritten sequentially.)

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

key, key: Switches to another page.

Sim22-15 TROUBLE 1/2 Sim22-15 TROUBLE 2/2

XX-XX XX-XX XX-XX XX-XX XX-XX XX-XX XX-XX XX-XX XX-XX XX-XX XX-XX XX-XX

The display sequence is as shown below.

Sim22-15 TROUBLE 1/2

1 2 3 4

5 6 7 8

9 10 11 12

In this case, (1) is the latest one and (12) is the oldest.

22 SPF/RSPF jam counter display

Used to display the SPF/RSPF JAM counter. When [INTERRUPT] key is pressed, the machine goes to the sub code input window. When [CA] key is pressed, the machine exits the simulation mode.

Sim22-22 JAM CNT

SPF : nnnnnnn

key

Contents Remark

XX-XX XX-XX XX-XX XX-XX XX-XX XX-XX XX-XX XX-XX

(Only when the SPF/RSPF is installed.)

24 01 Jam total counter clear

When this simulation is executed, the clear confirmation window is displayed as shown below. When [OK] key or [START] key is pressed, the jam total count and the jam memory are cleared and the machine shifts to the sub code input window.

Sim24-1 COUNTER CLR JAM COUNTER CLEAR

AER YOU SURE? EXEC

02 Trouble memory clear

Used to clear the trouble memory and the trouble history data in the EEPROM. When [INTERRUPT] key is pressed, the machine shifts to the sub code input window. When [CA] key is pressed, the machine exits the simulation mode.

Sim24-2 COUNTER CLR TROUBLE CLEAR

AER YOU SURE? EXEC

COUNTER

04 SPF/RSPF counter clear

Used to clear the SPF/RSPF paper feed counter.

Sim24-4 COUNTER CLR SPF

COUNTER

CLEAR

AER YOU SURE? EXEC

(Only when the SPF/RSPF is installed.)

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

MX-M182 SIMULATIONS 7-15

Main code

Sub

code

24 05 Duplex print counter clear

Used to clear the duplex print counter.

Sim24-5 COUNTER CLR DUPLEX

COUNTER

CLEAR

AER YOU SURE? EXEC

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

06 Paper feed counter clear

Used to clear the paper feed counter data in each paper feed section.

(Initial window) (Counter selection window) (Confirmation window)

Sim24-6 COUNTER CLR Sim24-6 COUNTER CLR Sim24-6 COUNTER CLR

1:BYPASS 2:TRAY1 3:TRAY2

4:TRAY3 5:TRAY4

* TRAY2-TRAY4 are displayed only when they are installed. [CA] key: Exits the simulation mode.

[INTERRUPT] key: Shifts to the sub code input window.

07 Drum counter clear

Numeric Key

[C] Key

Contents Remark

[OK] key or

[START] key

Return

[OK] key or

[START] key

1:BYPASS 2:TRAY1 3:TRAY2 ARE YOU SURE?

4:TRAY3 5:TRAY4

1:BYPASS 2:TRAY1 3:TRAY2

4:TRAY3 5:TRAY4

(Execution is not allowed when DUPLEX setting is OFF.)

Used to clear the drum counter and the drum rotating time.

Sim24-7 COUNTER CLR DRUM

COUNTER

CLEAR

AER YOU SURE? EXEC

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

08 Copy counter clear

Used to clear the copy counter.

Sim24-8 COUNTER CLR COPIES

COUNTER

CLEAR

AER YOU SURE? EXEC

[OK] key or [START] key: Clears the copy counter and shifts to the sub code input window. [CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

09 Printer counter clear

Used to clear the printer counter and other counters. Select a counter to be cleared and press [OK] key or [START] key. The confirmation window is displayed. Press [OK] key or [START] key again, and the specified counter is cleared and the machine returns to the initial window.

Numeric key input

Sim24-9 COUNTER CLR Sim24-9 COUNTER CLR

1:PRINT 2:OTHER

[OK] key or [START] key

1:PRINT

2:OTHER

[BACK] key

[OK] key or [START] key (Counter clear)

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

MX-M182 SIMULATIONS 7-16

1ARE YOU SURE?

Main code

Sub

code

24 10 FAX-related counter clear

Used to clear the current FAX send/receive counter value (number of pages of send/receive), the accumulated time of send/receive, and the print counter to 0.

Contents Remark

Sim24-10 CLR COUN.

CLEAR FAX COUNTER 1:SEND 2:RECEIVE (1 - 3) X

[1] key [2] key

[OK] key [OK] key

Sim24-10 CLR COUN.

SEND PAGE: xx, xxx, xxx TIME: hhhhhhhh:mm:ss EXEC

[OK] key [OK] key

Sim24-10 CLR COUN.

SEND COUN. CLEARED

Return Return Return

When the number of pages of send is cleared, the PC-FAX counter is also cleared.

13 Scanner counter clear

Used to clear the scanner counter.

Sim24-13 COUNTER CLR

SCAN

COUNTER

CLEAR

AER YOU SURE? EXEC

Sim24-10 CLR COUN.

CLEAR FAX COUNTER 3:PRINT PAGE (1 - 3) X

Sim24-10 CLR COUN.

RECEIVE PAGE: xx, xxx, xxx TIME: hhhhhhhh:mm:ss EXEC

Sim24-10 CLR COUN.

RCV COUN. CLEARED

CA key : Simulation cancel Interrupt key : Sub code input window

[3] key

[OK] key

Sim24-10 CLR COUN.

PRINT PAGE xxxxxxxx

EXEC

[OK] key

Sim24-10 CLR COUN.

FAX COUN. CLEARED

[OK] key or [START] key: Clears the scanner counter and shifts to the sub code input window. [CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

14 SPF/RSPF jam total counter clear

Used to clear the SPF/RSPF jam total counter.

Sim24-14 COUNTER CLR

SPF JAM

COUNTER

CLEAR

AER YOU SURE? EXEC

[OK] key or [START] key: Clears the SPF/RSPF jam total counter and shifts to the sub code input window. [CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

15 Scanner mode counter clear

Used to clear the scanner mode counter.

Sim24-15 COUNTER CLR

SCANNER MODE COUNTER

CLEAR

AER YOU SURE? EXEC

[OK] key or [START] key: Clears the scanner mode counter and shifts to the sub code input window. [CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

(Only when the SPF/RSPF is installed.)

MX-M182 SIMULATIONS 7-17

Main code

Sub

code

Contents Remark

25 01 Main motor operation check (Cooling fan motor rotation check)

When [OK] key or [START] key is pressed, the main motor (as well as the duplex motor in the case of the duplex model) is rotated for 30 sec. If the developing unit is installed to save toner consumption at that time, the developing bias, the main charger, and the grid are also outputted. In addition, since laser discharge is required when the motor is stopped, the polygon motor is also operated. Check if the developing unit is installed or not. If it is not installed, the previous high voltage is not outputted and only the motor is rotated. After completion of 30sec operation, the machine shifts to the sub code input window. * This simulation must not be executed with the door open/close switch forcibly turned ON.

(Execution start window) (Execution window)

Sim25-1 MAIN MOTOR

[OK] key or [START] Key

Sim25-1 MAIN MOTOR

PRESS OK KEY EXEC

EXEC

After completion of the process, the machine shifts to the sub code input window. [CA] key: Exits the simulation mode. [INTERRUPT] key: Interrupts the output operation, and shifts to the sub code input window.

02 Auto developer adjustment (Initial setting of toner density when replacing developer)

To execute this simulation, perform the following procedures.

[Procedures]

1) Check to confirm that the machine power is turned OFF. Install the DV unit.

2) With the cover open, turn ON the machine power.

3) The machine goes to the SIM25-02 mode. ("Cover open MSG" is displayed. Start LED: OFF.)

4) Close the side cover. (Start LED:ON)

5) Press [OK] key or [START] key. When [OK] key or [START] key is pressed, the main motor rotates for 3 minutes to determine the toner

sensor reference value and clear the developer rotation time, in addition, the developer counter is cleared. When the procedures are completed normally, the ATC sensor reference value is displayed on the value

display section. In case of an error, the following screen is displayed.

(Execution start)

Sim25-2 AutoDv ADJ.

(Executing)

Sim25-2 AutoDv ADJ.

DEVELOPER ADJUST

PRESS OK KEY EXEC

(Normally completed) (EL error) (EU error)

Sim25-2 AutoDv ADJ.

DEVELOPER ADJUST

COMPLETE [nnn]

[OK] key or [START] Key

Sim25-2 AutoDv ADJ.

DEVELOPER ADJUST

EL trouble [nnn]

DEVELOPER ADJUST

[nnn]

EXEC

Sim25-2 AutoDv ADJ.

DEVELOPER ADJUST

EU trouble [nnn]

Note: When the machine is not in the simulation mode, if the front cover is closed and the machine power is turned ON, toner may be supplied from the toner cartridge to the developer cartridge. Under this state, the toner density reference control level adjustment cannot be performed properly. If, therefore, the front cover is closed and the machine power is turned ON when the machine is not in the simulation mode, dispose developer, supply new developer, and adjust the toner density reference level. It takes about 3 minutes to complete the SIM25-02. Never open the front cover or turn OFF the machine power during execution of this simulation.

MX-M182 SIMULATIONS 7-18

Main

Window display Code number Setting

1: B4/LG, FC 0 FC detection disable (The set values to items marked with

are ignored.)

1 (Follows the setting of items below marked with .)

2: Use Mex Legal 0 Mexican legal detection disable (FC detection enable)

1 Mexican legal detection enable (FC detection disable)

Unit to

be used

Destination Destination Detection size

1: B4/LG, FC: 0

1: B4/LG, FC

2: Use Mex

Legal: 0

2: Use Mex

Legal: 1

Document SPF EX Japan AB

series (FC)

FC(8.5"x13") B4 FC

(8.5"x13")

Mexican legal (8.5"x13.4")

B4 Inch series (FC)

FC(8.5"x13") LG

(8.5"x14")

LG(8.5"x14")

code

Sub

code

25 10 Polygon motor operation check

When [OK] key or [START] is pressed, the polygon motor is rotated for 30sec.

(Execution start window) (Execution window)

Sim25-10 LSU CHECK

[OK] key or [START] Key

Contents Remark

Sim25-10 LSU CHECK

PRESS OK KEY EXEC

26 01 Job separator setting

Used to set YES/NO of installation of the hob separator. After installation of the job separator, setting must be manually set to YES.

Sim26-1 JBS SET

1:JOB SEPARATOR 0=NONE 1=SEPARATOR [ 0-1]

[CA] key: Exits the simulation mode. (When setting is changed, the machine exits the simulation mode and performs the hard reset.) [INTERRUPT] key: Shifts to the sub code input window. (When setting is changed, it is invalid.) [START] key: Setting contents are saved in the EEPROM and the machine shifts to the code input window.

(When setting is changed, the machine does not shift to the code input window.)

02 Size setting

Used to set Enable/Disable of FC (8.5" x 13") size detection and mexican legal size detection.

0 : No job separator 1 : Job separator provided

EXEC

Detection size when FC (8.5" x 13") size and mexican legal size document is used.

* For destinations other than the above, this setting is invalid.

Sim26-2 SIZE SET

1:B4/LG,FC 2:Use Max Legal 0

[ 0-1]

Code: Setting 0 : Detection disabled

1 : FC detection enabled

MX-M182 SIMULATIONS 7-19

Main

Setting Total/Developer Maintenance

0+2+2 1+1+2 2+2+1 3+1+1

code

Sub

code

26 03 Auditor setting

Used to set the auditor.

Sim26-3 AUDITOR SET

1:AUDITOR 0=P10 1=VENDOR 2=OTHER [ 0-2]

* When the coin vendor mode is selected:

1. Sort auto select is OFF.

2. For Japan, the duplex copy use inhibition setting is ON (inhibited).

3. When the auditor mode exclusive-setting is ON (manual paper feed inhibited) and the standard tray is set to the manual feed tray, the standard tray setting is set to the main tray.

04 Copier duplex setting

Used to set YES/NO of duplex setting. This must be set to ON when the duplex unit is installed. If this setting is set to OFF on the duplex machine, the duplex motor does not rotate and paper is not discharged normally, resulting in a paper jam.

Sim26-4 DUPLEX SET

1:DUPLEX 0=OFF 1=ON

[ 0-1]

Code: Mode 0 : Built-in auditor mode

1 : Coin vendor 2 : Other

Code: Duplex setting 0 : OFF

1 : ON

Contents Remark

Default: 0

Default: 0: MX-M182

1: MX-M182D

MX-M202D MX-M232D

05 Count mode setting

Used to set the count-up number of the total counter, the developer counter, and the maintenance counter individually when a special paper (A3/WLT/8K) is passed. When this simulation is executed, the current set value is displayed.

Sim26-5 COUNT MODE

1:COUNT MODE

[ 0-3]

[1]-[3]: Enter a value with numeric keys, and press [OK] key or [START] key to save the current adjustment value to the EEPROM. The machine returns to the sub code input window.

Default: 0

MX-M182 SIMULATIONS 7-20

Main code

Sub

code

26 06 Destination setting

Used to set the destination of the main unit. When this simulation is executed, the code number of currently set destination is displayed.

Sim26-6 DESTINATION

1:DESTINATION 0=JAPAN

[ 0-6]

[0] - [6] (Default: Depends on the model.) Enter a value with numeric keys, and press [OK] key or [START] key, and the current adjustment value is saved in the EEPROM. [CA] key: Exits the simulation mode. (When setting is changed, the machine exits the simulation mode and

performs the hard reset.) [INTERRUPT] key: Shifts to the sub code input window. (When setting is changed, it is invalid.) [START] key: Setting contents are saved in the EEPROM and the machine shifts to the code input window.

(When setting is changed, the machine does not shift to the code input window.)

* When this setting is changed, the following adjustment values and the set values are automatically

changed according to the set destination. O SIM46-19 ( table setting) O SIM46-30 (AE limit setting) O Paper size (A4 for AB series, LT for inch series) O Maintenance cycle (Returns to the default (Japan/Ex Japan). ) O Mini maintenance cycle (Only when setting is changed to Japan.)

07 Machine condition check

Contents Remark

Code :Setting 0=JAPAN : Japan AB series

1=INCH : Inch series 2=AB : Ex Japan AB series 3=INCH(FC) : Ex Japan inch series (FC)

4=AB(FC) : Ex Japan AB series (FC) 5=CHINESE : China (EX Japan AB series + Chinese paper support) 6=TAIPEI : Taiwan (EX Japan AB series + Chinese paper support) (Setting range 0 - 6)

Default: Differs depending on each destination.

When this simulation is executed, the copy speed of the machine is displayed.

Sim26-7 CPM CHECK

18CPM

Displayed CPM list 18CPM 20CPM 23CPM

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

08 Manual transfer shaking countermeasures setting

Used to set the countermeasures against manual transfer shaking. When this simulation is executed, the current set value is displayed. Enter a set value with numeric keys and press [OK] key or [START] key. The set value is saved in the EEPROM.

Sim26-08 TC FADE SET

1:TC FADE 0=OFF 1=ON

[ 0-1]

Code: Setting 0: Manual transfer shaking countermeasures OFF

1: Manual transfer shaking countermeasures ON

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

18 Toner save mode setting

Used to switch ON/OFF of the toner save mode. When this simulation is executed, the current set value is displayed. Enter a set value with numeric keys and press [OK] key or [START] key. The set value is saved in the EEPROM. * When this setting is changed, the toner save setting of the system settings is also changed accordingly.

Sim26-18 TONER SAVE

1:TONER SV MODE 0=OFF 1=ON

[ 0-1]

Code: Setting 0: Toner save OFF

1: Toner save ON

Default: 0

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

MX-M182 SIMULATIONS 7-21

Main code

Sub

code

26 20 Job separator paper exit mode setting

Used to set the paper exit mode of the job separator. * The purpose is to allow the simplified check when the job separator option is installed. It is valid only

during the adjustment simulation. Without installing a printer or a FAX machine, paper is discharged to

the upper stage to check if there is no problem or not.

If SIM26-01 is set to "Job separator not installed," paper is discharged to the lower stage regardless of

this setting.

Sim26-20 JOBSEP OUT

1:JOBSEP OUT 0=OFF 1=ON

[ 0-1]

Code: Setting 0: Lower tray 1: Upper tray

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

22 Language setting clear

Used to clear the language setting. The scanner head is shifted to the fixing lock position.

(Intial display)

Sim26-22 LANGUAGE

LANGUAGE SETTING CLEAR

AER YOU SURE? EXEC

[OK] key or [START] Key

Contents Remark

Default: 0

(Execution is started)

Sim26-22 LANGUAGE

LANGUAGE SETTING CLEAR

EXEC

Sim26-22 LANGUAGE

PLEASE SHUT OFF THE POWER.

After completion of counter clear and shifting to the lock position.

30 CE mark conformity control ON/OFF

Used to set Yes/No of CE mark conformity. When this simulation is executed, the current set value is displayed. Enter a value with numeric keys and press [OK] key or [START] key. The set value is saved to EEPROM and the machine returns to the sub code input window.

Sim26-30 CE MARK

1:CE MARK CTRL 0=OFF 1=ON

[ 0-1]

Code: Setting 0 : CE mark support control OFF

1 : CE mark support control ON

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

Default: 0: 100V series 1: 200V series

MX-M182 SIMULATIONS 7-22

Main

Code: Setting 0 : Stop 1 : Cancel of stop

Sim26-37 DEVE STOP 1:DEV LIFE OVER

[ 0 - 1]1 1

code

Sub

code

26 31 Auditor mode exclusive setup

Used to set whether paper feed is allowed from the manual paper feed tray of not when the auditor is set to the coin vendor mode.

Sim26-31 AUDITOR

1:AUDITOR

[ 0-2]

Code: Setting 0 : Exclusive setting OFF (Manual paper feed enable)

1 : Exclusive setting ON (Manual paper feed disable) 2 : Exclusive setting OFF (Manual paper feed enable) + A3/WLT charge

* When this setting is set to ON, if the auditor mode is the coin vendor mode and the standard tray setting

is set to the manual paper feed tray, the standard tray setting is set to the main tray.

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

36 Cancel of stop at maintenance life over

"Stop" or "Cancel of stop" can be selected when the maintenance counter reaches the life over.

Sim26-36 MAINTESTOP

1:MAINTE OVER

Code: Setting 0 : Stop

1 : Cancel of stop

Contents Remark

Default: 1

[ 0-1]

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code entry menu.

37 Cancel of stop at developer life over

"Stop" or "Cancel of stop" can be selected when the developer counter reaches the life over..

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code entry menu.

39 Memory capacity check

Used to check the capacity of the image memory (SDRAM) installed to the MCU PWB and the capacity of the IMC compression memory.

Sim26-39 MEMORY CHK

MCU : 128Mbyte

There are two kinds of the displayed image memory capacity: 16MB and 32MB. The standard capacity of the IMC compression memory is 16B. * It is not displayed when IMC is not installed.

Default: 1

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

MX-M182 SIMULATIONS 7-23

Main

1:TC(ON) 2:TC(OFF)

PS release TC ON PIN OFF TC OFF

Set value Time (ms) Difference (ms) Set value Time (ms) Difference (ms)

99 442 +122 99 402 +98

• • • • • • • • • • • • • • • • • • 50 344 +24 51 306 +2

• • • • • • • • • 50 304 0 38 320 0 49 302 -2

• • • • • • • • • • • • • • • • • •

1 246 -74 1 206 -98

1:TC(ON) 2:TC(OFF)

PS release TC ON PIN OFF TC OFF

Set value Time (ms) Difference (ms) Set value Time (ms) Difference (ms)

99 367 101 99 334 82

• • • • • • • • • • • • • • • • • • 50 286 20 51 254 2

• • • • • • • • • 50 252 0 38 266 0 49 251 -1

• • • • • • • • • • • • • • • • • •

1 204 -62 1 171 -81

code

Sub

code

26 42 Transfer ON/OFF timing control setting

Used to set the ON/OF timing of the transfer charger (TC) individually. Select an item to be changed with the arrow keys, and change the set value to a desired value, and press [OK] key or [START] key. The entered value is saved to the EEPROM and the machine shifts to the sub code input window.

(Item selection)

Sim26-42 TC TIMING Sim26-42 TC TIMING Sim26-42 TC TIMING

1:TC(ON) 2:TC(OFF)

[ 1- 99]

Contents Remark

(Value input) (Settlement)

1:TC(ON) 2:TC(OFF)

[ 1- 99]

1:TC(ON) 2:TC(OFF)

[ 1- 99]

Default: 38 (TC ON) 50 (TC OFF)

Key, Key

Variation in the adjustment value

•18cpm/20cpm machine

•23cpm machine

Numeric Key

[OK] key or [START] Key

* Setting range is 1 - 99.

In the case of 88mm/s, when the set value is increased by 1, the timing is increased by 2ms. [CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

43 Side void amount setting

Used to set the left and right side void amounts. The left side void amount and the right side void amount can be set individually. Select an item to be changed with the arrow keys and change the set value to a desired value. The setting range is 0-10. When the value is increased by 1, the void amount is increased by

0.5mm. The default is 5 (= 2.5mm).

(Item selection)

Sim26-43 SIDE VOID Sim26-43 SIDE VOID Sim26-43 SIDE VOID

1:SIDE VOID(L) 2:SIDE VOID(R)

[ 0- 10]

Display: Set item 1:SIDE BOID(L) : Left side void amount setting 2:SIDE VOID(R) : Right side void amount setting

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

Key, Key

(Value input) (Settlement)

1:SIDE VOID(L) 2:SIDE VOID(R)

[ 0- 10]

Numeric Key

MX-M182 SIMULATIONS 7-24

1:SIDE VOID(L) 2:SIDE VOID(R)

[ 0- 10]

[OK] key or [START] Key

Default: 5 (Void amount:

2.5mm)

Main

Sim26-56 LIFE SET 1:AE1 2:AE2 3:TEXT 1/3 [ 0- 1]

1 1

Sim26-56 LIFE SET 4:PHOTO 1 5:PHOTO 2 6:AE(TS)1 2/3 [ 0- 1]

1 1

Sim26-56 LIFE SET 7:AE(TS)2 8:TEXT(TS)

3/3 [ 0- 1]

1 1

Screen display : adjustment mode 1: AE1 2: AE2 3: TEXT 4: PHOTO 1

: AE1 life correction : AE2 life correction : TEXT life correction : PHOTO (Error diffusion) life correction

Screen display : Adjustment mode 5:PHOTO 2 6:AE(TS)1 7:AE(TS)2 8:TEXT(TS)

: PHOTO(Dither) life correction : TSAE1 life correction : TSAE2 life correction : TSTEXT life correction

FAX P W B Setting Yes No 0 (Enable) FAX window display FAX not-installed display 1 (Disable) FAX window display Error beep sound

code

Sub

code

26 51 Copy temporary stop function setting

Used to set whether copying is stopped temporarily when the paper exit tray full is detected. When the electronic sort function is used, paper exit of 250 sheets (*1) or more can be used for one copy job. If, at that time, copying (paper discharge) is continued with the tray full, a paper exit jam may occur. To avoid this, copying is temporarily stopped by this setting.

Sim26-51 COPY STOP 1:COPIES STOP

0=NON STOP 1=STOP

[ 0-1]0 1

Display: Setting 0 : Temporary stop cancel 1 : Temporary stop

(*1) 150 sheets when the job separator is installed. [CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

54 LCD contrast PWM duty setting

Used to set the PWM duty (brightness) at the center value of LCD contrast. * Setting range: 30-70 * When [OK] key or [START] key is pressed, the set value of LCD contrast is immediately reflected.

Sim26-54 LCD DUTY

1:LCD PWM DUTY

Contents Remark

Default: 1

Default: 50

[ 30- 70]

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

56 Life correction ON/OFF setting

The image correction ON/OFF setting is made according to the usage level (life) of developer. When this simulation is executed, the list of the modes and the current set value are displayed on the LCD. Select an item to be changed with the arrow keys, and change the set value to the required value. (1=ON [Enable], 0=OFF [Disable]) When [OK] key or [START] key is pressed, the setting is saved to the EEPROM.

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

60 [FAX] key Enable/Disable setting

Used to set Enable/Disable of the [FAX] key when the FAX PWB is not installed. Though this setting is set to Enable, if the FAX PWB is not installed, a message of "FAX PWB is not installed" is displayed. * When the FAX PWB is installed, the display shifts to the FAX window regardless of this setting.

Sim26-60 FAX KEY

1:FAX KEY MODE

Default: 1: 1 2: 1 3: 1 4: 1 5: 1 6: 1 7: 1 8: 1

Default: 0

[ 0- 1]0 0

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

MX-M182 SIMULATIONS 7-25

Main

Code number Setting contents

0 Toner near end is displayed 1 Toner near end is not displayed

Code number Setting contents

0 Operation setting 1 1 Operation setting 2 2 Operation setting 3

r r r

code

Sub

code

26 69 Toner near end environment setting (Function)

This simulasion is used to set the operating conditions for toner near end. The setting mode is switched by [Density select] key. The set value of the selected mode is displayed on the LCD display. When the code number is entered and [START] key is pressed, the setting is switched. <Toner near end display /No display>

Contents Remark

73 Toner save setting display/non-display

Used to set Enable/Disable of the toner save setting in the system settings. If this setting is set to Enable (1), the toner save setting appears in the system settings to allow setting.

Sim26-73 TS ENABLE 1:TS ENABLE

[ 0- 1]0 0

Display: Setting 0 : Disable 1 : Enable

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

74 Total counter display change setting

Used to set whether the scanner counter value is added to the total counter display in the system settings.

Sim26-74 ADD COUNT

1:ADD SCAN CNT

[ 0- 1]0 0

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

30 01 Paper sensor status display

Used to display the list of paper sensor status on the LCD. An active sensor is highlighted. The display items and corresponding sensors are shown below.

Sim30-1 SENSOR POUT DPX PIN

MBEMP C1EMP C2EMP C3EMP C4EMP C2PSS C3PSS C4PSS

Default: 1

Default: 0

0 : Scan counter not added 1 : Scan counter added

Display : Corresponding sensor POUT : Paper exit sensor DPX : DUPLEX sensor PIN : Paper entry sensor MBEMP : Manual feed paper sensor C1EMP : No. 1 tray paper sensor C2EMP : No. 2 tray paper sensor C3EMP : No. 3 tray paper sensor C4EMP : No. 4 tray paper sensor C2PSS : No. 2 tray paper feed senso C3PSS : No. 3 tray paper feed senso C4PSS : No. 4 tray paper feed senso

When a multi-stage cassette is not installed as an option, the corresponding sensor name is not displayed.

MX-M182 SIMULATIONS 7-26

Main

OC cover open/close sensor status Document sensor status

OCSW Open Close PD1 - PD5 Document NO Document

YES

Highlighted Normal display Normal display Highlighted

OCSW Original cover status

Open: Highlighted Close: Normal display

1 - 5 PD sensor detection level

code

Sub

code

41 01 Document size detection photo sensor check

Used to check the operation of the document sensor. When this simulation is executed, the status of the document sensor is displayed. An active sensor display is highlighted.

Sim41-1 PD SENSOR

OCSW PD1 PD2

PD3 PD4 PD5

* For AB series, PD1-PD5; for inch series, PD1 - PD4.

02 Document size detection photo sensor detection level adjustment

When this simulation is executed, the detection level of the OC document size detection sensor is displayed. (Real time display) Place white paper of A3 or WLT on the document table and press [OK] key or [START] key with the OC cover open. When [START] key is pressed, "EXEC" is highlighted and the document detection level at that moment is saved in the EEPROM. (The saved value is used as the reference for the following document size detection control.)

Execution window Sensor position for AB series Sensor position for Inch series

Sim41-2 PD SENSOR

OCS

1[128] 200 3[128] 200 5[128] 200

2[128] 200 4[128] 200

1 2 3

Contents Remark

5 4

1 2

4 3

The values are displayed in the range of 0 - 255. 0 (Black) - 255 (White) The value in [ ] indicates the adjustment threshold value. "EXEC" is highlighted during execution.

03 Document size detection photo sensor light receiving/detection level check

When this simulation is executed, the light receiving level of the document detection photo sensor is displayed. (Real time display) The values in parentheses of sensor 4 and 5 are the threshold values of adjustment at SIM41-04. Since sensors 1 and 3 are not provide with the threshold value of detection at SIM41-04, "0" is always displayed.

Sim41-3 PD SENSOR

OCS

1[000] 200 3[000] 200 5[050] 200

2[000] 200 4[050] 200

04 Detection level adjustment when the document size is settled (15 degrees - 20 degrees)

Set the OC cover to the document size settled state (15 degrees - 20 degrees), and press [OK] key.

1 Initial window

Sim41-4 20 SENSOR

PRESS OK KEY EXEC

2 After-execution window

Sim41-4 20 SENSOR

OCS

1[000] 163 3[001] 167 5[197] 179

2[000] 148 4[0C6] 180

The detection level under the document size settled state is saved in the EEPROM, and the value is displayed in [ ]. * The document size settled state means the point when the open/close sensor (OCSW) is switched from

ON (highlighted) to OFF (normal display).

MX-M182 SIMULATIONS 7-27

Main

NO. 012345678910111213141516

Temperature (°C) 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230

NO. 012345678

Temperature (°C) 80 90 100 110 120 130 140 150 160

code

Sub

code

42 01 Developing counter clear

Used to clear the developing counter. When this simulation is executed, the confirmation window is displayed to confirm to clear or not. To clear, press [OK] key or [START] key. Not to clear, press [INTERRUPT] key or [CA] key to exit the simulation mode.

Sim42-1 COUNTER CLR

DEVELOPER COUNTER CLEAR

ARE YOU SURE? EXEC

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

43 01 Fusing temperature setting 1

When this simulation is executed, the current set value is displayed. Every time when [ ] key is pressed, the current display value is increased. For the set value, refer to Table 1 and 2. Every time when [ ] key is pressed, the current display value is decreased. For the set value, refer to Table 1 and 2. Enter a desired set value (temperature), and press [OK] key or [START] key. The set value is caved in the EEPROM.

Sim43-1 FUSER TMP 1

1:READY 2:NORMAL 3:THICK

170

165

180

170

Contents Remark

Sim43-1 FUSER TMP 2 4:MOTORON

5:MOTOROFF 6:WEPEND

100

Window display Setting item Setting range 1: READY Main thermistor target temperature during standby 150 - 230 *1 2: NORMAL Main thermistor target temperature during plain paper 

transmission *5 150 - 230 *2

3: THICK Main thermistor target temperature during heavy paper 

transmission 150 - 230 *3

4: MOTORON Main thermistor temperature when starting main motor 

preliminary rotation 80 - 160 *4 5: MOTOROFF Main motor preliminary rotation end time (sec) 0 - 90 6: WUPEND Warm-up compulsory termination time (sec) 0 - 90

*1: When the set value is increased by 1, the target temperature is increased by 5°C. (Refer to Table 1.) *2: When the set value is increased by 1, the target temperature is increased by 10°C. (Refer to Table 2.) *3: When the set value is increased by 1, the target temperature is increased by 5°C. (Refer to Table 1.) *4: When the set value is increased by 1, the target temperature is increased by 10°C. (Refer to Table 2.) *5: The correction temperature applied to the current target temperature differs depending on the paper

size. For details, refer to SIM43-04.

Table 1:

Table 2:

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

Default: READY: 170 NORMAL:  150 (18/20cpm machine) 165 (23cpm machine) THICK: 180 MOTORON: 100 MOTOROFF: 0 WUPEND: 23

MX-M182 SIMULATIONS 7-28

Main

NO. 012345678910111213141516

Temperature (°C) 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230

NO. 012345678910111213141516

Temperature (°C) 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230

NO. 012345678

Temperature (°C) 80 90 100 110 120 130 140 150 160

code

Sub

code

43 02 Fusing temperature setting 2

When this simulation is executed, the current set value is displayed. Every time when [ ] key is pressed, the current display value is increased. For the set value, refer to Table 1. Every time when [ ] key is pressed, the current display value is decreased. For the set value, refer to Table 1. Enter a desired set value (temperature), and press [OK] key or [START] key. The set value is caved in the EEPROM.

Sim43-2 FUSER TMP 2 1:SUSPEND

2:RESUME 3:COOLDOWN

230

180

230

Contents Remark

Window display Setting item Setting range 1: SUSPEND Sub thermistor temperature when shifting to high temperature alarm 150 - 230 *1 2: RESUME Sub thermistor temperature when canceling high temperature alarm 150 - 230 *2 3: COOLDOWN Main motor rotation time (sec) after completion of a JOB 0 - 90

*1, *2: When the set value is increased by 1, the target temperature is increased by 5°C. (Refer to Table 1.)

Table 1:

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

03 Fusing temperature setting 3

When this simulation is executed, the current set value is displayed. Every time when [ ] key is pressed, the current display value is increased. For the set value, refer to Table 1 and 2. Every time when [ ] key is pressed, the current display value is decreased. For the set value, refer to Ta b le 1 and 2. Enter a desired set value (temperature), and press [OK] key or [START] key. The set value is caved in the EEPROM.

Sim43-3 FUSER TMP 3 1:PREHEAT

2:WARMUP1 3:WARMUP2

110

100 150

110

Default: SUSPEND: 230 RESUME: 180 COOLDOWN: 0

Window display Setting item Setting range 1: PREHEAT Main thermistor target temperature during preliminary heating 80 - 160 *1 2: WARMUP1 When the initial temperature is below 120°C during warm-up 150 - 230 *2

Main thermistor target temperature 3: WARMUP2 When the initial temperature is above 120°C during warm-up 150 - 230 *3

Main thermistor target temperature

*1: When the set value is increased by 1, the target temperature is increased by 10°C. (Refer to Table 2.) *2: When the set value is increased by 1, the target temperature is increased by 5°C. (Refer to Table 1.) *3: When the set value is increased by 1, the target temperature is increased by 5°C. (Refer to Table 1.)

Table 1:

Table 2:

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

MX-M182 SIMULATIONS 7-29

Default: PREHEAT: 110 WARMUP1: 160 WARMUP2: 150

Main

NO. 012345678

Temperature (°C) -20 -15 -10 -5 0 5 10 15 20

Setting mode LOW Setting in normal temperature adjustment (190°C or below) HIGH When the fusing temperature is 190°C or above

code

Sub

code

43 04 Fusing temperature setting 4

When this simulation is executed, the current set value is displayed. Every time when [ ] key is pressed, the current display value is increased. For the set value, refer to Table 3. Every time when [ ] key is pressed, the current display value is decreased. For the set value, refer to Table 3. Enter a desired set value (temperature), and press [OK] key or [START] key. The set value is caved in the EEPROM.

Sim43-4 FUSER TMP 4

1:TMPFIRST 2:TMPLAST 3:CNTFIRTS

-5 3

Contents Remark

Sim43-4 FUSER TMP 4

4:CNTTYPE1 5:CNTTYPE2 6:CNTTYPE3

50 25 50

Window display Setting item Setting range 1: TMPFIRST JOB initial correction temperature *3 -20 - 20 *1 2: TMPLAST JOB latter-half correction temperature *4 -20 - 20 *2 3: CNTFIRST JOB initial temperature correction number of sheets 0 - 255 4: CNTTYPE1 JOB latter-half temperature correction number of sheets 

(Paper size: A3/WLT) 0 - 255

5: CNTTYPE2 JOB latter-half temperature correction number of sheets 

(Paper size: A4/LT) 0 - 255

6: CNTTYPE3 JOB latter-half temperature correction number of sheets 

(Paper size: except A3/WLT/A4/LT) 0 - 255

*1, *2: When the set value is increased by 1, the target temperature is increased by 5°C. (Refer to Table 3.) *3: Correction temperature from starting a JOB to reaching the JOB initial temperature correction number

of sheets

*4: Correction temperature from the JOB initial temperature correction number of sheets to JOB end

Table 3:

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

43 12 Standby mode fusing fan rotation setting

When this simulation is executed, the currently set code number is displayed. Select a mode to be changed with the arrow keys and enter a set value with numeric keys. Enter the mode number to be selected with numeric keys and press [OK] key or [START] key. The set value is saved in the EEPROM.

Sim43-12 FAN SPEED 1:LOW

2:HIGH

FAN rotation speed 0 : Low speed rotation 1 : High speed rotation

Default: TMPFIRST: 5 TMPLAST: -5 CNTFIRST: 3 CNTTYPE1: 50 CNTTYPE2: 50 CNTTYPE3: 25

Default: LOW:0 HIGH:1

[ 0-1]

MX-M182 SIMULATIONS 7-30

Main code

Sub

code

Contents Remark

43 13 Paper interval control allow/inhibit setting

Used to change the paper feed timing of 21st sheet or later to A3 or WLT (depending on the destination setting) when in multi copy/print of narrow width sheets. When this simulation is executed, the current set number is displayed. Enter a code number and press [START] key. The entered number is saved in the EEPROM and the machine returns to the sub code input window.

Sim43-13 PICK INTVL 1:PICK INTVL

[ 0-1]0 0

Code: Setting 0: Disable (Default) 1: Enable

1) Cassette paper feed: A4R,B5R,8-1/2"x14",8-1/2"x13",8-1/2"x11",A5,INV

2) Manual paper feed: A4R,B5R,8-1/2"x14",8-1/2"x13",8-1/2"x11",A5,INV,16KRÅ * A5 is applicable to manual paper fed only in EX Japan AB series.

44 01 Enable/Disable setting of toner density control correction

Enable/Disable of toner density control correction is set. When this simulation is executed, the list of the modes and the current set value are displayed on the LCD. "Select an item to be changed with the cross key, and change the set value to the required value. (1=ON [Enable], 0=OFF [Disable])" When [OK] key or [START] key is pressed, the setting is saved to the EEPROM.

Sim44-1 TONER CONT

1:COV 2:LIFE 3:DRIP 1/2 [ 0- 1]

0 0

Sim44-1 TONER CONT 4:BETA 5:UNCONDITIONAL

2/2 [ 0- 1]

Default: 0

Default: COV: 1 LIFE:  0

(18/20cpm machine)



1 (23cpm machine) DRIP: 0 BETA: 0 UNCONDITIONAL: 1

0 0

Display mode : Setting mode Display : Setting COV LIFE DRIP BETA UNCONDITIONAL

: Print ratio correction : Life correction : Drip supply : Purge process : Unconditional toner supply

0 : Disable 1 : Enable

<Descriptions of each correction> Print ratio correction In this correction, the toner supply interval is determined according to the print ratio to prevent against overtoner. Note for corrections marked with Since "Drip supply" and "Purge process" are simulations for analysis, do not set them to "1" [Enable]. If they are set to "1" [Enable], the toner density rises or falls abnormally and developer failure or toner dispersion occurs. If they are set to "1" [Enable] erroneously, developer must be replaced, and the inside of the machine and the process unit must be cleaned.

Unconditional toner supply When the developing unit and the drum unit are rotating, a small quantity of toner is consumed. For assuring this operation, toner is supplied according to the rotation time of the developing unit.

16 Toner density control data check and toner density correction quantity display

The output value of the ATC sensor is checked, and the toner density control correction quantity is displayed on the LCD.

Sim44-16 TONER DISP

1:TONER DEN_LT

2:TONER DEN_ST

nnn

Name TONER DEN_LT TONER DEN_ST

:Display content :Current ATC sensor value :ATC reference value with life correction quantity added

[CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

MX-M182 SIMULATIONS 7-31

Main

Display mode : Setting mode NML F : Normal size paper (Front) NML R : Normal size paper (Back) SML F : Small size paper (Front) SML R : Small size paper (Back) BYPASS : Manual paper pass

Window display : Adjustment mode 1:AE : AE MODE (600dpi) 2:TEXT : TEXT MODE (300dpi) 3:PHOTO 1 : PHOTO MODE (Error diffusion) 4:PHOTO 2 : PHOTO MODE (Dither) 5:TEXT (TS) : TS MODE (TEXT) (600dpi) 6:AE (TS) : TS MODE (AE) (600dpi)

code

Sub

code

44 34 Transfer current setting

Used to set the transfer current value. When this simulation is executed, the list of modes and the current set value are displayed on the LCD.

Sim44-34 TC ADJ. 1:NML F

2:NML R 3:SML F 1/2 [ 9- 36]

21 22

Select a set item with the arrow keys and enter a set value with numeric keys. Press [OK] key or [START] key, and the set value is saved in the EEPROM. The setting range is 90µA - 360µA. The calculation formula is "Set value x 10 (µA)." For example, in order to set the transfer current value to 200µA, set the adjustment value to "20."

* Small size paper means A4R (Letter R) width or less. * When selecting the special size of tray, the normal size width setting is made.

46 02 Copy density adjustment (600dpi)

Contents Remark

Default: NML F: 22 NML R: 21 SML F: 22

Sim44-34 TC ADJ.

4:SML R 5:BYPASS

2/2 [ 9- 36]

SML R: 21 BYPASS: 22

Used to set the copy density for each mode.

Sim46-2 EXP. LEVEL

1:AE 2:TEXT 3:PHOTO 1 1/2 [ 1- 99]

50 50

Sim46-2 EXP. LEVEL 4:PHOTO 2

5:TEXT(TS) 6:AE(TS) 2/2 [ 1- 99]

50 50

Used to set the copy density for each mode. When this simulation is executed, the list of the setting items and the current set value are displayed. Select an item to be changed with [ ] key and [ ] key and enter the adjustment value with numeric keys. The setting range is 1 - 99. When [ ] key or [ ] key is pressed, the page is changed. Enter the adjustment value with numeric keys and press [OK] key. The entered value is saved in the EEPROM and the machine shifts to the copy window. Sample copying can be performed during the simulation.

MX-M182 SIMULATIONS 7-32

Main

1 1.0(SHIFT) TEXT density 1 shift amount 2 1.0(GAMMA) TEXT density 1 gamma value 3 2.0(SHIFT) TEXT density 2 shift amount 4 2.0(GAMMA) TEXT density 2 gamma value 5 3.0(SHIFT) TEXT density 3 shift amount 6 3.0(GAMMA) TEXT density 3 gamma value 7 4.0(SHIFT) TEXT density 4 shift amount 8 4.0(GAMMA) TEXT density 4 gamma value

9 5.0(SHIFT) TEXT density 5 shift amount 10 5.0(GAMMA) TEXT density 5 gamma value 11 TS 1.0(SHIFT) TS TEXT density 1 shift amount 12 TS 1.0(GAMMA) TS TEXT density 1 gamma value 13 TS 2.0(SHIFT) TS TEXT density 2 shift amount 14 TS 2.0(GAMMA) TS TEXT density 2 gamma value 15 TS 3.0(SHIFT) TS TEXT density 3 shift amount 16 TS 3.0(GAMMA) TS TEXT density 3 gamma value 17 TS 4.0(SHIFT) TS TEXT density 4 shift amount 18 TS 4.0(GAMMA) TS TEXT density 4 gamma value 19 TS 5.0(SHIFT) TS TEXT density 5 shift amount 20 TS 5.0(GAMMA) TS TEXT density 5 gamma value

code

Sub

code

Contents Remark

46 10 Copy exposure level adjustment, individual setting (Text) 600dpi

Used to adjust the shift amount and the slanting value for each density level (1-5) when the exposure model is TEXT (including TS).

• For the shift amount, the gamma (gradation) is common. The whole sections are made brighter or darker. When the shift amount is increased, the brightness is decreased. When the shift amount is decreased, the brightness is increased.

• The slanting value changes the gamma (gradation).

When the set value is increased, the gamma is increased to provide a higher contrast. (Clear black and white) When the set value is decreased, the gamma is decreased to provide a lower contrast. (Higher gradation) Select an adjustment mode with the arrow keys, and enter the set value with numeric keys. The adjustment range is 1 - 99. When [ ] key or [ ] key is pressed, the page is changed. The shift amount and the slanting value can be individually set for each of five levels of density for each of TEXT/TS and TEXT. Therefore, there are 20 patterns of adjustment modes.

Sim46-10 TEXT 600 1:1.0(SHIFT)

2:1.0(GAMMA) 3:2.0(SHIFT) 1/7 [ 1- 99]

50 50

Sim46-10 TEXT 600 4:2.0(GAMMA)

5:3.0(SHIFT) 6:3.0(GAMMA) 2/7 [ 1- 99]

50 50

Sim46-10 TEXT 600

7:4.0(SHIFT) 8:4.0(GAMMA) 9:5.0(SHIFT) 3/7 [ 1- 99]

50 50

Sim46-10 TEXT 600

10:5.0(GAMMA) 11:TS 1.0(SHIFT) 12:TS 1.0(GAMMA) 4/7 [ 1- 99]

The value on the example (50) is not the default value.

50 50

Sim46-10 TEXT 600 13:TS 2.0(SHIFT)

14:TS 2.0(GAMMA) 15:TS 3.0(SHIFT) 5/7 [ 1- 99]

50 50

Select an item to be changed and set a desired adjustment value. Press [OK] key, and the machine shifts to the copy window. When [START] key is pressed at that time, copying is performed with the previous adjustment value and the result can be checked.

Sim46-10 TEXT 600

16:TS 3.0(GAMMA) 17:TS 4.0(SHIFT) 18:TS 4.0(GAMMA) 6/7 [ 1- 99]

MX-M182 SIMULATIONS 7-33

50 50

Sim46-10 TEXT 600

19:TS 5.0(SHIFT) 20:TS 5.0(GAMMA)

7/7 [ 1- 99]

Main

1 ED 1.0(SHIFT) PHOTO (Error diffusion) density 1 shift amount 2 1.0(GAMMA) PHOTO (Error diffusion) density 1 gamma value 3 ED 2.0(SHIFT) PHOTO (Error diffusion) density 2 shift amount 4 ED 2.0(GAMMA) PHOTO (Error diffusion) density 2 gamma value 5 ED 3.0(SHIFT) PHOTO (Error diffusion) density 3 shift amount 6 ED 3.0(GAMMA) PHOTO (Error diffusion) density 3 gamma value 7 ED 4.0(SHIFT) PHOTO (Error diffusion) density 4 shift amount 8 ED 4.0(GAMMA) PHOTO (Error diffusion) density 4 gamma value

9 ED 5.0(SHIFT) PHOTO (Error diffusion) density 5 shift amount 10 ED 5.0(GAMMA) PHOTO (Error diffusion) density 5 gamma value 11 DI 1.0(SHIFT) PHOTO (Dither) density 1 shift amount 12 DI 1.0(GAMMA) PHOTO (Dither) density 1 gamma value 13 DI 2.0(SHIFT) PHOTO (Dither) density 2 shift amount 14 DI 2.0(GAMMA) PHOTO (Dither) density 2 gamma value 15 DI 3.0(SHIFT) PHOTO (Dither) density 3 shift amount 16 DI 3.0(GAMMA) PHOTO (Dither) density 3 gamma value 17 DI 4.0(SHIFT) PHOTO (Dither) density 4 shift amount 18 DI 4.0(GAMMA) PHOTO (Dither) density 4 gamma value 19 DI 5.0(SHIFT) PHOTO (Dither) density 5 shift amount 20 DI 5.0(GAMMA) HOTO (Dither) density 5 gamma value

code

Sub

code

Contents Remark

46 11 Copy exposure level adjustment, individual setting (Photo) 600dpi

Used to adjust the shift amount and the slanting value for each density level (1-5) when the exposure model is PHOTO (error diffusion and dither).

• The slanting value changes the gamma (gradation). When the set value is increased, the gamma is increased to provide a higher contrast. (Clear black and white)



When the set value is decreased, the gamma is decreased to provide a lower contrast. (Higher gradation)

Select an adjustment mode with the arrow keys, and enter the set value with numeric keys. The adjustment range is 1 - 99. When [ ] key or [ ] key is pressed, the page is changed. The shift amount and the slanting value can be individually set for each of five levels of density for each of PHOTO mode (error diffusion and dither). Therefore, there are 20 patterns of adjustment modes.

The value on the example (50) is not the default value.

Sim46-11 PHOTO 600 1:ED 1.0(SHIFT)

2:ED 1.0(GAMMA) 3:ED 2.0(SHIFT) 1/7 [ 1- 99]

Sim46-11 PHOTO 600

4:ED 2.0(GAMMA)

5:ED 3.0(SHIFT)

6:ED 3.0(GAMMA)

2/7 [ 1- 99]

Sim46-11 PHOTO 600 13:DI 2.0(SHIFT)

14:DI 2.0(GAMMA) 15:DI 3.0(SHIFT) 5/7 [ 1- 99]

Sim46-11 PHOTO 600

16:DI 3.0(GAMMA)

17:DI 4.0(SHIFT)

18:DI 4.0(GAMMA)

6/7 [ 1- 99]

MX-M182 SIMULATIONS 7-34

50 50

Sim46-11 PHOTO 600 7:ED 4.0(SHIFT)

8:ED 4.0(GAMMA) 9:ED 5.0(SHIFT) 3/7 [ 1- 99]

Sim46-11 PHOTO 600 19:DI 5.0(SHIFT)

20:DI 5.0(GAMMA)

7/7 [ 1- 99]

50 50

Sim46-11 PHOTO 600

10:ED 5.0(GAMMA) 11:DI 1.0(SHIFT) 12:DI 1.0(GAMMA) 4/7 [ 1- 99]

50 50

Main

Sim46-14 EXP LEVEL

After input 1 - 4

After input 0 - 99

[OK] key

Sim46-14 EXP LEVEL

FINE 1:AE(PHOTO ON) 2:AE(PHOTO OFF) (1㧙4) X

FINE XX AE PHOTO ON

(2DIGITS) YY

[OK] key

FINE YY AE PHOTO ON

EXEC

FINE YY AE PHOTO ON

SCAN EXEC

FINE YY AE PHOTO ON

PRINT EXEC

Sim46-14 EXP LEVEL

FINE 3:MANUAL(PHOTO ON) 4:MANUAL(PHOTO OFF) (1㧙4) X

Sim46-13 EXP LEVEL

After input 1 - 2

After input 0 - 99

[OK] key

Sim46-13 EXP LEVEL

STD. 1:AE 2:MANUAL (1-2) X

STD. XX AE

(2DIGITS) YY

[OK] key

STD. YY AE

EXEC

STD. YY AE

SCAN EXEC

STD. YY AE

PRINT EXEC

XX: Adjustment value of current state YY: Inputted adjustment value

code

Sub

code

Contents Remark

46 12 Density adjustment in the FAX mode (Collective adjustments)

Used to adjust the density in the FAX mode to "AUTO" or "0" - "99".

Sim46-12 EXP LEVEL

AUTO XX

( 2DIGITS ) YY

After input 0 - 99

[OK] key

Sim46-12 EXP LEVEL

AUTO YY

EXEC

XX: Adjustment value of current state

YY: Inputted adjustment value

Sim46-12 EXP LEVEL

AUTO YY

PRINT EXEC

Sim46-12 EXP LEVEL

AUTO YY

SCAN EXEC

13-16 Density adjustment in the FAX mode (Individual adjustments)

Used to adjust the density in the FAX mode to "AUTO" or "0" - "99".

MX-M182 SIMULATIONS 7-35

Main

[OK] key[OK] key

Sim46-15 ':2.'8'.

S-FINE 1:AE(PHOTO ON) 2:AE(PHOTO OFF) (1㧙) X

S-FINE XX AE PHOTO ON

(2DIGITS) YY

S-FINE YY AE PHOTO ON

EXEC

S-FINE YY AE PHOTO ON

SCAN EXEC

S-FINE YY AE PHOTO ON

PRINT EXEC

Sim46-15 ':2.'8'.

S-FINE 3:MANUAL(PHOTO ON) 4:MANUAL(PHOTO OFF) (1㧙) X

After input 1 - 4

After input 0 - 99

Sim46-16 ':2.'8'.

U-FINE 1:AE(PHOTO ON) 2:AE(PHOTO OFF) (1㧙) X

U-FINE XX AE PHOTO ON

(2DIGITS) YY

U-FINE YY AE PHOTO ON

EXEC

U-FINE YY AE PHOTO ON

SCAN EXEC

U-FINE YY AE PHOTO ON

PRINT EXEC

Sim46-16 ':2.'8'.

U-FINE 3:MANUAL(PHOTO ON) 4:MANUAL(PHOTO OFF) (1㧙) X

After input 1 - 4

After input 0 - 99

XX: Adjustment value of current state YY: Inputted adjustment value

Code number table setting 1 Priority on image quality 2 Priority on toner consumption

Code number AE operation mode 0 Lead edge stop 1 Real time process (All areas)

Code number Image process mode 1 Error diffusion process 2 Dither process

code

Sub

code

46 13-16

Contents Remark

19 Exposure mode setting ( table setting/AE operation mode setting/Photo image process setting)

Used to set the following three items. Select an item with the [ ] key or [ ] key and enter a set value with numeric keys. (1) : table setting (2) : AE operation mode (3) : PHOTO image process setting When this simulation is executed, the current set code number of the above three modes are displayed.

Sim46-19 AE MODE

1:AE MODE 2:AE STOP 3:PHOTO

[ 1- 2]

(1) AE MODE( table setting) Used to set the priority operation mode of the AE mode. When the image takes priority regardless of the toner consumption, set to 1. When the toner consumption must be suppressed regardless of image quality, set to 2.

* If this setting is changed, SIM 46-30 returns to the default. (2) AE STOP (AE operation mode)

Used to set the area for automatic exposure correction in image process.

0 1

(3) PHOTO (PHOTO image process setting) Used to set the image process when the PHOTO mode is selected. Selection is available in the following two modes:

Default: 2

Default: 0

Default: 2

MX-M182 SIMULATIONS 7-36

Main

Display text Copy mode 1:AE AE mode (600dpi) 2:TEXT TEXT mode (600dpi) 3:PHOTO 1 PHOTO mode (Error diffusion) 4:PHOTO 2 PHOTO mode (Dither) 5:TEXT (TS) TONER SAVE mode (TEXT)(600dpi) 6:AE (TS) TONER SAVE mode (AE)(600dpi)

code

Sub

code

46 20 SPF/RSPF exposure correction

Used to set the exposure correction amount in the SPF/RSPF mode. (Since a slightly darker image is outputted in the SPF/RSPF mode compares to the OC mode, the difference from the OC mode is corrected with this simulation. When, therefore, the exposure in the OC mode is corrected, the SPF/RSPF exposure is also changed accordingly.) Enter a correction value with numeric keys and press [OK] key. The adjustment value is saved in the EEPROM and the machine shifts to the adjustment copy window. Since this simulation is used to make up for the exposure difference from the OC mode regardless of the exposure mode, the adjustment is fixed to TEXT mode and the exposure mode cannot be changed. After completion of copying for check, the machine returns to the setting window.

Sim46-20 SPF EXP.

1:SPF EXPOSURE

Contents Remark

(Only when the SPF/RSPF is installed.)

Default: 50

[ 1- 99]

The adjustment value is in the range of 1 - 99. Adjustment value (Image change) 99 (Dark) • • • 50 (Default) • • • 1 (Light)

29 Image contrast adjustment (600dpi)

Used to adjust the image contrast for each mode. When this simulation is executed, the current set value of each mode is displayed in two digits. (Default: 50)

(Adjustment item selection window) (Copy start window)

Sim46-29 GAMMA SET Ready to copy.

1:AE 2:TEXT 3:PHOTO 1 1/2 [ 1-99]

50 50

100%

8 1/2×11

(Copy execution window)

Copies in progress.

100%

8 1/2×11

Select an adjustment item (mode) with the arrow keys and enter a desired value with numeric keys. When [OK] key is pressed, the entered value is saved to the EEPROM and the machine shifts to the copy execution window. After completion of copying, the machine returns to the adjustment value input window. When [START] key is pressed instead of [OK] key, the machine shifts to the copy execution window and performs copying.

Default: AE: 50 TEXT: 50 PHOTO1: 50 PHOTO2: 50 TEXT (TS): 50 AE (TS): 50

[BACK] key

Adjustment

item selection

window

[START] key

End of copy execution

[OK] key

Copy start

window

[START] key

Copy execution

window

MX-M182 SIMULATIONS 7-37

Main

Display text Copy mode 1:AE AE mode 2:TEXT TEXT mode 3:PHOTO 1 PHOTO mode (Error diffusion) 4:PHOTO 2 PHOTO mode (Dither) 5:TEXT (TS) TONER SAVE mode 6:AE (TS) TONER SAVE mode

Set value Image quality

0 Shading 1 Standard 2 Sharpening

code

Sub

code

46 30 AE limit setting

Used to set the limit value in AE and AE (toner save) mode. When this simulation is executed, the selection window of the adjustment items and the current set value are displayed.

(Adjustment item selection window)

Sim46-30 AE LIMIT 1:AE

2:AE(TS)

[ 0- 255]

Select an item to be changed with [ ] key and [ ] key and enter a desired value with numeric keys. The entered value is saved to the EEPROM. The adjustment value is in the range of 0 - 255.

* Note: When SIM26 - 06 (Destination setting) and SIM46 - 19 (Auto exposure mode) are changed, this

setting returns to the default accordingly.

31 Image sharpness adjustment

Used to adjust sharpening/shading of image for each mode. When this simulation is executed, the selection window of the adjustment items and the current set value are displayed.

(Adjustment item selection window)

Sim46-31 SHARPNESS

1:AE 2:TEXT 3:PHOTO 1 1/2 [ 0- 2]

Contents Remark

Default: 196

Window display : Mode

1: AE : AE limit value

2: AE (TS) : AE (Toner save) limit value

Default: AE: 1 TEXT: 1 PHOTO1: 1 PHOTO2: 1

Sim46-31 SHARPNESS

1 1

4:PHOTO 2 5:TEXT(TS) 6:AE(TS) 2/2 [ 0- 2]

1 1

TEXT (TS): 1 AE (TS): 1

The adjustment range is in the range of 0 - 2. Select an adjustment item (mode) with the arrow keys and enter a desired value with numeric keys. When [OK] key is pressed, the entered value is saved to the EEPROM and the machine shifts to the copy execution window. After completion of copying, the machine returns to the adjustment value input window. When [START] key is pressed instead of [OK] key, the machine shifts to the copy execution window and performs copying.

(Copy start window)

Ready to copy.

100%

8 1/2×11

(Copy execution window)

Copies in progress.

100%

8 1/2×11

[BACK] key

Adjustment

item selection

window

[START] key

End of copy execution

[OK] key

MX-M182 SIMULATIONS 7-38

Copy start

window

[START] key

Copy execution

window

Main code

Sub

code

Contents Remark

46 39 FAX IMAGE adjustment

Used to adjust the resolution and the filer in the FAX mode.

The current set value of each resolution is displayed.

Sim46-39 FAX IMAGE

1:STD. 1 2:FINE 1 3:S-FINE 1 (1 - 7 ) X

1 - 7 input

Specify a resolution

[BACK] key

Sim46-39 FAX IMAGE

STD. X

(0 - 2 ) Y

[BACK] key

Sim46-39 FAX IMAGE

STD. Y

EXEC

* When "Interrupt" key is pressed on a window other than the operation window, the display shifts to the sub code input window.

[OK] key

to be set.

0 - 2 input

Specify the kind

[OK] key

of a filter to be set.

[OK] key

Self print operation is executed. (The specified kind of the filter is used.)

The specified filter is used even in the normal operation.

Sim46-39 FAX IMAGE

4:U-FINE 1 5:FINE/HT 1 6:S-FINE/HT 1 (1 - 7 ) X

Scanning operation

Sim46-39 FAX IMAGE

STD. Y

SCAN EXEC

48 01 Main/sub scanning magnification ratio adjustment

Used to adjust the magnification ratio in the main scanning (front/rear) direction and the sub scanning direction. When this simulation is executed, the selection window of the adjustment items and the current set value are displayed

(Adjustment item selection window)

Sim48-1 COPY MAG.

1:F-R 2:SCAN

[ 1- 99]

Display text array : Adjustment mode

1: F-R : Main scan direction magnification ratio (OC/SPF/RSPF)

2: SCAN : Sub scan direction magnification ratio (OC)

Sim46-39 FAX IMAGE

7:U-FINE/HT 1

(1 - 7 ) X

Printing operation

Sim46-39 FAX IMAGE

STD. Y

PRINT EXEC

Default: F-R: 50 SCAN: 50

The adjustment value is in the range of 1 - 99. When the adjustment value is increased by 1, the ratio is increased by 0.1%. Select an adjustment item (mode) with the arrow keys and enter a desired value with numeric keys. When [OK] key is pressed, the entered value is saved to the EEPROM and the machine shifts to the copy execution window. After completion of copying, the machine returns to the adjustment value input window. When [START] key is pressed instead of [OK] key, the machine shifts to the copy execution window and performs copying.

(Copy start window)

Ready to copy.

100%

8 1/2×11

(Copy execution window)

Copies in progress.

100%

8 1/2×11

Adjustment

item selection

window

[START] key

[BACK] key

[OK] key

End of copy execution

Copy start

window

[START] key

Copy execution

window

MX-M182 SIMULATIONS 7-39

Main code

Sub

code

Contents Remark

48 05 SPF/RSPF mode sub scanning magnification ratio adjustment in copying

Used to adjust the sub scanning magnification ratio in the SPF/RSPF mode. When this simulation is executed, the selection window of the adjustment items and the current set value are displayed.

(Adjustment item selection window)

Sim48-5 (R)SPF ZOOM 1:RSPF(SIDE1)

2:RSPF(SIDE2)

[ 1- 99]

Display text array : Adjustment mode

1: RSPF (SIDE1) : SPF/RSPF sub scan direction magnification

ratio adjustment on the front of document

2: RSPF (SIDE2) : RSPF sub scan direction magnification ratio

setting on the back of document

The adjustment value is in the range of 1 - 99. When the adjustment value is increased by 1, the ratio is increased by 0.1%.

(Copy start window)

Ready to copy.

100%

8 1/2×11

(Copy execution window)

Copies in progress.

100%

8 1/2×11

Simplex" or "Duplex Duplex" mode with the [DUPLEX] key.

[BACK] key

Adjustment

item selection

window

[START] key

End of copy execution

[OK] key

* The exposure mode is fixed to "TEXT" with density 3, and cannot be changed. * For the model without RSPF, the adjustment item of document back is not displayed.

08 FAX magnification ratio adjustment (scan)

(Only when the SPF/RSPF is installed.) Default: RSPF(SIDE1): 50 RSPF(SIDE2): 50

Copy start

window

[START] key

Copy execution

window

Used to adjust and set the FAX document scan magnification ratio and scan and print the document.

Sim48-8 SCAN RATIO

1:OC 2:SPF 3:RSPF ( 1 - 3 ) X

Sim48-8 SCAN RATIO

MAIN SCANNING/OC XXX

PRINT EXEC

Sim48-8 SCAN RATIO

OC 1:MAIN SCAN XXX

After input 1 - 3

[OK] key

2:SUB SCAN XXX ( 1 - 2 )

XX: Adjustment value of current state YY: Inputted adjustment value

Sim48-8 SCAN RATIO

MAIN SCANNING/OC XXX

SCAN EXEC

After input 1 - 2

[OK] key

Sim48-8 SCAN RATIO

MAIN SCANNING/OC XXX

( 1 - 255 ) YYY

After input 1 - 255

[OK] key

Sim48-8 SCAN RATIO

MAIN SCANNING/OC XXX

EXEC

09 FAX magnification ratio adjustment (print)

Used to adjust and set the FAX print magnification ratio and scan and print the document.

Sim48-9 PRI. RATIO

1:MAIN SCAN XXX 2:SUB SCAN XXX 3:MAIN SCAN/R XXX ( 1 - 4 )

After input 1 - 4

[OK] key

Sim48-9 PRI. RATIO

MAIN SCAN XXX

( 1 - 255) YYY

XX: Adjustment value of current state YY: Inputted adjustment value

After input 1 - 255

[OK] key

Sim48-9 PRI. RATIO

4:SUB SCAN/R XXX

( 1 - 4 )

Sim48-9 PRI. RATIO

MAIN SCAN XXX

EXEC

Sim48-9 PRI. RATIO

MAIN SCAN XXX

PRINT EXEC

Sim48-9 PRI. RATIO

MAIN SCAN XXX

SCAN EXEC

MX-M182 SIMULATIONS 7-40

Main

(When entering the download mode)

Connect the main unit and the download PC with a USB cable, and start downloading with the maintenance tool. When downloading is started, the display is changed as follows:

(Receiving download data)

(Processing download data)

* Contents during processing the

download data

• FLASH ROM data erase

• Writing the received data into the FLASH

• Sum check

(When downloading is completed)

(When an error occurs)

MCU PANEL

0xFF No process No process 0x00 OK OK 0x03 Data receive error (Protocol error 2) Flash Rom write error (Program section) 0x04 Loader transfer error Flash Rom write error (Common window data) 0x05 Flash Rom delete error (Boot) Flash Rom write error (Copy window data) 0x06 Flash Rom delete error (Program) Flash Rom write error (Scan window data) 0x07 Flash Rom write error (Boot) Flash Rom write error (Print window data) 0x08 Flash Rom write error (Program) Flash Rom write error (Fax window data) 0x09 Flash Rom LOCK error (Boot) 0x0A Flash Rom LOCK error (Program) Data writing start address illegal error 0x0B Sum check error (Loader) FROM size error 0x0C Sum check error (Boot) Destination error 0x0D Sum check error (Program) Download file structure error 0x0E Sum check error (EEPROM) 0x0F EEPROM read error 0x10 EEPROM write error Sum check error (Boot not-written) 0x11 EEPROM verify error Sum check error (Loader) 0x12 Download data length error Sum check error (After Boot writing) 0x17 Sum check error (Print window data) 0x18 Sum check error (Fax window data) 0x19 FAX communication error Panel-MCU communication error 0x1A PANEL communication error 0x1B Download file error

code

Sub

code

49 01 Flash Rom program writing mode (MCU)

Used to download the programs and data sections of the main unit MCU board, the FAX board, and the operation panel. When this simulation is executed, the machine immediately shifts to the download mode and the following display is shown.

Contents Remark

Download Mode.

Download Data

Receiving.

Do not turn the

power off.

Processing finished.

Turn off the power.

ɢError.

MCU : -FAX : --

PNL : --

Used to display an error code at the error position in downloading of MCU/FAX/PANEL. The error codes to be displayed are shown below.

MX-M182 SIMULATIONS 7-41

Main

FAX

0xFF No process 0x44 FONT Flash write error 0x00 OK 0x45 FONT Flash sum check error 0x01 Download impossible 0x52 Registration data work sum check error 0x02 Total data size error 0x56 Registration data format error 0x03 LOADER no file 0x57 Registration data items insufficient error 0x04 DWLD no file 0x58 Registration data items overlap error 0x05 BOOT no file 0x61 BOOT data size error 0x06 MAIN no file 0x62 BOOT work sum check error 0x07 FONT download impossible 0x63 BOOT Flash erase error 0x08 Option FLASH connection error 0x64 BOOT Flash write error 0x09 Option FLASH no match 0x65 BOOT Flash sum check error 0x11 LOADER data size error 0x71 MAIN data size error 0x12 LOADER work sum check error 0x72 MAIN work sum check error 0x21 BOOT data size error 0x73 MAIN Flash erase error 0x22 BOOT work sum check error 0x74 MAIN Flash write error 0x23 BOOT Flash erase error 0x75 MAIN Flash sum check error 0x24 BOOT Flash write error 0x81 FONT data size error 0x25 BOOT Flash sum check error 0x82 FONT work sum check error 0x31 MAIN data size error 0x83 FONT Flash erase error 0x32 MAIN work sum check error 0x84 FONT Flash write error 0x33 MAIN Flash erase error 0x85 FONT Flash sum check error 0x34 MAIN Flash write error 0x91 DWLD data size error 0x35 MAIN Flash sum check error 0x92 DWLD work sum check error 0x41 FONT data size error 0x93 DWLD Flash erase error 0x42 FONT work sum check error 0x94 DWLD Flash write error 0x43 FONT Flash erase error 0x95 DWLD Flash sum check error

(When entering the download mode)

(Processing download data)

* Contents during processing

the download data

• FLASH ROM data erase

• Writing the received data into the FLASH

• Sum check

(When downloading is completed)

(When an error occurs)

Downloaded Mode.

Do not turn the

power off.

code

49 01

Sub

code

Contents Remark

02 Flash Rom program writing mode (NNB)

Used to write the program into NNB by using USB memory.

(Preliminary arrangement)

1. Save the NNB download file to the root directory of the USB memory.

2. Insert the USB memory into the USB port of the NNB board.

When this simulation is executed, the machine immediately shifts to the download mode and the following display is shown.

Processing finished.

Turn off the power.

Note: The operations are enabled only when the MX-NB12 is active.

It takes 30 seconds for the MX-NB12 from turning ON the power to activating. When turning ON the power, therefore, wait for 30 seconds before executing SIM49-02. Once the process is started, never disconnect the USB memory until the end of the process. It is allowed to save only one NNB download file (*.bm file) in the root directory of the USB memory.

ġĢġError. MCU : NNB : 0D

FAX :

MX-M182 SIMULATIONS 7-42



Main

Display text :Adjustment mode 1:TRAY1 :Print start position (TRAY1) 2:TRAY2 (*) :Print start position (TRAY2 - TRAY4) 3:MFT :Print start position (MULTI BYPASS) 4:DEN-A :Image lead edge void amount 5:RRC-A :Document scanning start position 6:DEN-B :Image rear edge void amount

code

Sub

code

50 01 Image lead edge adjustment

Used to adjust the following items related to the lead edge adjustment.

1.Print start position (Offset between output image and paper Adjusted for each tray.)

2.Image lead edge void (Margin on the output image lead edge)

3.Document scanning start position (Image scanning start position in the sub scanning direction) When this simulation is executed, the selection window of the adjustment items and the set value are displayed.

(Adjustment item selection window)

Sim50-1 LEAD EDGE 1:TRAY1

2:TRAY2 3:MFT 1/2 [ 1- 99]

50 50

Note 1: Items marked with (*) are displayed when TRAY2 and following options are not installed. Note 2: When executing an adjustment copy from the manual paper feed tray, set the following paper.

AB series A3 paper Inch series Double Letter paper

Note 3: When the adjustment value of the print start position adjustment is increased by 1, the ON timing of

the resist roller is delayed and the print result is shifted to the lead edge by 0.1mm.

Note 4: When the adjustment value of the image scanning start position is increased by 1, the scanning

start position is shifted to the home position by about 0.1mm, increasing the image loss amount.

Note 5: When the print start position (TRAY1) is changed, the print start positions (TRAY2 - TRAY4) and the

print start position (MULTI BYPASS) are also changed accordingly. The adjustment value is in the range of 1 - 99. Select an adjustment item (mode) with the arrow keys, and enter the set value with numeric keys.

Contents Remark

Default: TRAY1: 50 TRAY2: 50 MFT: 50 DEN-A: 50 RRC-A: 50 DEN-B: 50

Sim50-1 LEAD EDGE

4:DEN-A 5:RRC-A 6:DEN-B 2/2 [ 1- 99]

50 50

When [OK] key is pressed, the entered value is saved to the EEPROM and the machine shifts to the copy execution window. After completion of copying, the machine returns to the adjustment value input window. When [START] key is pressed instead of [OK] key, the machine shifts to the copy execution window and performs copying.

(Copy start window)

Ready to copy.

100%

8 1/2×11

(Copy execution window)

Copies in progress.

100%

8 1/2×11

[BACK] key

Adjustment

item selection

window

[START] key

End of copy execution

[OK] key

MX-M182 SIMULATIONS 7-43

Copy start

window

[START] key

Copy execution

window

Main code

Sub

code

50 01 (Adjustment procedure)

(1) Set the print start position (1: TRAY1), the lead edge void amount (4: DEN - A), and the scanning start

position (5: RRC - A) to "1" and make a copy of 100%.

(2) Measure the image loss amount (R mm) of the scale.

Set [5:RRC - A] = 10xR(mm). (Example. Set 40.) When the value of [5: RRC - A] is increased by 10, the image loss is decreased by1mm.

(3) Measure the distance (H mm) from the paper lead edge to the image print start position.

Set [1:TRAY1] = 10xH(mm). (Example: Set 50.) When the value of [1:TRAY1] is increased by 10, the image lead edge shifts to the paper lead edge by 1mm.

(4) Set the lead edge void amount to B = 50(2.5mm).

When the value of [4:DEN - A] is increased by 10, the void amount is increased by about 1mm. (For 25 or less, the void amount is zero.)

[Example]

Contents Remark

Copy output result

Distance between the paper lead edge to the image lead edge H=5.0mm

Paper lead edge

Scale image loss amount R=4.0mm

06 Copy lead edge position adjustment (SPF/RSPF)

Used to perform the image lead edge adjustment in the SPF/RSPF copy.

When this simulation is executed, the selection window of the adjustment items and the current set value are displayed.

(Adjustment item selection window)

Sim50-6 SPF EDGE 1:SIDE1

2:SIDE2 3:END EDGE

[ 1- 99]

50 50

Display text array : Adjustment mode 1: SIDE1 : Document (front) scan start position adjustment 2: SIDE2 : Document (back) scan start position adjustment 3: END EDGE : Document rear edge image loss adjustment

The adjustment value is in the range of 1 - 99. When the adjustment value of the document scanning start position is increased by 1, the scanning timing is advanced, resulting in a smaller image loss.

(Copy start window)

Ready to copy.

100%

×11

8 1/2

(Copy execution window)

Copies in progress.

100%

8 1/2×11

Adjustment

item selection

window

[START] key

End of copy execution

[BACK] key

[OK] key

Copy start

window

[START] key

Copy execution

window

(Only when the SPF/RSPF is installed.) Default: SIDE1: 50 SIDE2: 50 END EDGE: 50

MX-M182 SIMULATIONS 7-44

Main

Display text :Adjustment mode 1:TRAY1 :Print center offset (TRAY1) 2:TRAY2 (*) :Print center offset (TRAY2) 3:TRAY3 (*) :Print center offset (TRAY3) 4:TRAY4 (*) :Print center offset (TRAY4) 5:BYPASS :Print center offset (BYPASS) 6:DUPLEX (*) :Print center offset (DUPLEX 2nd print surface)

code

Sub

code

50 08 FAX lead edge adjustment (scan)

Used to adjust and set the FAX document scan lead edge position and scan and print the document.

Sim50-8 SCAN EDGE

1:OC 2:SPF 3:RSPF ( 1 - 3 ) X

After input 1 - 3

[OK] key

Sim50-8 SCAN EDGE OC

1:LEAD EDGE XX 2:LEFT EDGE XX ( 1 - 4 ) X

After input 1 - 4

[OK] key

Sim50-8 SCAN EDGE LEAD EDGE/OC XX

( 43- 57 ) YY

XX: Adjustment value of current state YY: Inputted adjustment value

After input 43 - 57

[OK] key

10 Paper off-center adjustment

Used to adjust the output area (main scanning direction) of scanned image data on paper. When this simulation is executed, the selection window of the adjustment items and the current set value are displayed.

(Adjustment item selection window)

Sim50-10 1:TRAY1

2:TRAY2 3:TRAY3 1/2 [ 1- 99]

PRT. CENTER

50 50

Sim50-8 SCAN EDGE

OC 3:REAR EDGE XX 4:RIGHT EDGS XX ( 1 - 4 ) X

Sim50-8 SCAN EDGE

LEAD EDGE/OC XX

EXEC

Sim50-10

4:TRAY4 5:BYPASS 6:DUPLEX 2/2 [ 1- 99]

Contents Remark

Sim50-8 SCAN EDGE

LEAD EDGE/OC XX

PRINT EXEC

Sim50-8 SCAN EDGE

LEAD EDGE/OC XX

SCAN EXEC

Default:

TRAY1: 50 TRAY2: 50 TRAY3: 50 TRAY4: 50 BYPASS: 50

PRT. CENTER

50 50

DUPLEX: 50

Note 1: Items marked with (*) are displayed when TRAY2 and following options are not installed. Note 2: When executing an adjustment copy from the manual paper feed (BYPASS) tray, set the following

paper according to the destination specification.

AB series A3 paper

Inch series Double Letter paper The adjustment value is in the range of 1 - 99. When the adjustment value is increased, the output image is shifted to the right. When the adjustment value is increased by 1, the image is shifted to the right by about 0.1mm. Select an adjustment item (mode) with the arrow keys, and enter the set value with numeric keys.

MX-M182 SIMULATIONS 7-45

Main code

Sub

code

Contents Remark

50 10 When [OK] key is pressed, the entered value is saved to the EEPROM and the machine shifts to the copy

execution window.

After completion of copying, the machine returns to the adjustment value input window. When [START] key is pressed instead of [OK] key, the machine shifts to the copy execution window and performs copying.

(Copy start window)

Ready to copy.

100%

8 1/2×11

(Copy execution window)

Copies in progress.

100%

8 1/2×11

Adjustment

item selection

window

[START] key

End of copy execution

[BACK] key

[OK] key

Copy start

window

[START] key

Copy execution

window

12 Document off-center adjustment

Used to adjust the scanning start position in the main scanning direction of the document. When this simulation is executed, the selection window of the adjustment items and the current set value are displayed.

(Adjustment item selection window)

Sim50-12

ORG. CENTER 1:OC 2:SPF(SIDE1) 3:SPF(SIDE2)

[ 1- 99]

50 50

Display text array : Adjustment mode 1: OC : OC document off-center adjustment 2: SPF (SIDE1) : SPF/RSPF document (front) off-center adjustment 3: SPF (SIDE2) : RSPF document (back) off-center adjustment

(Note) 2:SPF(SIDE1) is available only for the model with the SPF/RSPF. (Note) 3:SPF(SIDE2) is available only for the model with RSPF.

The adjustment value is in the range of 1 - 99. When the adjustment value is increased, the document scanning position is shifted to the right and the image is shifted to the left as a result. When the adjustment value is increased by 1, the scanning area is shifted by 0.1mm.

Select an adjustment item (mode) with the arrow keys, and enter the set value with numeric keys. When [OK] key is pressed, the entered value is saved to the EEPROM and the machine shifts to the copy execution window. After completion of copying, the machine returns to the adjustment value input window. When [START] key is pressed instead of [OK] key, the machine shifts to the copy execution window and performs copying.

(Copy start window)

Ready to copy.

100%

×11

8 1/2

(Copy execution window)

Copies in progress.

100%

8 1/2×11

Adjustment

item selection

window

[START] key

End of copy execution

[BACK] key

[OK] key

Copy start

window

[START] key

Copy execution

window

Default:

OC: 50 SPF(SIDE1): 50 SPF(SIDE2): 50

MX-M182 SIMULATIONS 7-46

Main code

Sub

code

Contents Remark

50 18 Memory reverse position adjustment in duplex copy

Used to adjust the reverse point (scanning end position) on the reversed surface in duplex copy. When this simulation is executed, the selection window of the adjustment items and the current set value are displayed

(Adjustment item selection window)

Sim50-18 DUP REV.

1:OC 2:SPF

[ 1- 99]

Display text array : Adjustment mode 1: OC : OC memory reverse output position 2: SPF : RSPF memory reverse output position

The adjustment value is in the range of 1 - 99. Front surface print in S-D mode and even page print in D-S mode are reverse memory copy operations from the document rear edge. When, therefore, the print start position adjustment of the output image is required, adjust as follows:

The image in the reverse memory copy is printed from the scanning rear edge when the document scanning direction is in the arrow direction as shown below. If, therefore, the print lead edge is shifted, set the reference chart with the rear edge on the reference position, and adjust the simulation set value with this simulation so that the print image lead edge matches.

Since printing is started at the print start position from the last memory image data to the head data, the end data position saved in the memory is changed by changing the scanning end position with the simulation, adjusting the image lead edge position.

(Execution is allowed when DUPLEX setting is ON, and RSPF is installed.)

Default: OC: 50

SPF: 50

Document transport direction

Scan direction Scan rear edge

Scan lead edge

Scan end position (Default: Void (1) is not scanned.)

Paper transport direction

Print lead edge Lead edge void (1) Print start position

Rear edge void Print rear edge

(Copy start window)

Ready to copy.

100%

×11

8 1/2

(Copy execution window)

Copies in progress.

100%

8 1/2×11

Adjustment

item selection

window

[START] key

[BACK] key

[OK] key

End of copy execution

Copy start

window

[START] key

Copy execution

window

MX-M182 SIMULATIONS 7-47

Main

Display text :Adjustment mode 1:TRAY1 :Resist amount in paper feed from TRAY1 2:TRAY2 :Resist amount in paper feed from TRAY2 (*1) 3:TRAY3 :Resist amount in paper feed from TRAY3 (*1) 4:TRAY4 :Resist amount in paper feed from TRAY4 (*1) 5:BYPASS :Resist amount in paper feed from manual tray 6:RSPF(SIDE1) :Resist amount on SPF/RSPF document surface (*1) 7:RSPF(SIDE2) :resist amount on RSPF document back (*1) 8:RSPF A5 :Document resist amount in A5 document back transport (*1) 9:DUPLEX :Resist amount in DUPLEX print (Second print surface) (*1) 10: PRE FEED :Pre-feed time of the manual feed tray paper feed. (*2)

code

Sub

code

50 19 Rear edge void adjustment in duplex copy

Used to adjust the rear edge void amount in duplex copy. When this simulation is executed, the selection window of the adjustment items and the current set value are displayed.

(Adjustment item selection window)

Sim50-19 DUP R VOID

1:PRV(SIDE1) 2:PRV(SIDE2) 3:RRC-D

[ 1- 99]

50 50

Display text array : Adjustment mode 1: PRV (SIDE1) : Paper rear edge void amount (1st print surface) 2: PRV (SIDE2) : Paper rear edge void amount (2nd print surface) 3: RRC-D : Print start position (2nd print surface)

The adjustment value is in the range of 1 - 99. When the adjustment value is increased by 1, the rear edge void amount is increased by about 0.1mm.

(Copy start window)

Ready to copy.

100%

×11

8 1/2

(Copy execution window)

Copies in progress.

100%

8 1/2×11

Contents Remark

(Execution is allowed when DUPLEX setting is ON, and RSPF is installed.)

Default: PRV(SIDE1): 50 PRV(SIDE2): 50 RRC-D: 50

[BACK] key

Adjustment

item selection

window

[START] key

End of copy execution

[OK] key

Copy start

window

[START] key

Copy execution

window

51 02 Resist amount adjustment

Used to adjust the contact pressure (warp amount) of paper against the resist roller of the main unit resist roller and the SPF/RSPF. When this simulation is executed, the selection window of the adjustment items and the current set value are displayed.

(Adjustment item selection window)

Sim51-2 RESIST ADJ. Sim51-2 RESIST ADJ. Sim51-2 RESIST ADJ.

1:TRAY1 2:TRAY2 3:TRAY3 1/4 [ 1- 99]

Sim51-2 RESIST ADJ.

10:PRE FEED

4/4 [ 1- 99]5050

50 50

4:TRAY4 5:BYPASS 6:RSPF(SIDE1) 2/4 [ 1- 99]

MX-M182 SIMULATIONS 7-48

50 50

7:RSPF(SIDE2) 8:RSPF A5 9:DUPLEX 3/4 [ 1- 99]

50 50

Default: TRAY1: 50 TRAY2: 50 TRAY3: 50 TRAY4: 50 BYPASS: 50 RSPF(SIDE1): 50 RSPF(SIDE2): 50 RSPF A5: 50 DUPLEX: 50 PRE FEED: 32

Main code

Sub

code

Contents Remark

51 02 (*1) Valid only when an option is installed. (If an option is not installed, it is not displayed on the adjustment

window.) (*2) When heavy paper slips in manual feed copy, or when a paper jam occurs in thin paper copy, adjust this set value to remove the problem.

•Heavy paper slips. Increase the set value.

• Thin paper jams. Decrease the set value.

The adjustment range is 1 - 99. Select an adjustment item (mode) with the arrow keys, and enter the set value with numeric keys. When [OK] key is pressed, the entered value is saved to the EEPROM and the machine shifts to the copy execution window. After completion of copying, the machine returns to the adjustment value input window. When [START] key is pressed instead of [OK] key, the machine shifts to the copy execution window and performs copying.

(Copy start window)

Ready to copy.

100%

8 1/2×11

Adjustment

item selection

window

[BACK] key

[OK] key

Copy start

window

(Copy execution window)

Copies in progress.

100%

8 1/2×11

[START] key

53 08 SPF/RSPF scanning position automatic adjustment

Used to adjust the SPF/RSPF stop position of the mirror unit in the SPF/RSPF copy. The scanning position is basically determined by the automatic adjustment. It can be also adjusted manually.

(Automatic adjustment window)

Sim53-8 SPF AUTO

PRESS OK KEY EXEC 50

adjustment

[OK] key or [START] Key

Sim53-8 SPF AUTO

EXEC

Key

(Manual adjustment window)

Sub code input standby window

End of copy execution

Sim53-8 SPF AUTO

[START] Key

[START] key

Copy execution

window

An optional value can be entered manually. When [OK] key or [START] key is pressed, the entered value is saved in the EEPROM. When [START] key is

pressed, the window shifts to the sub code input standby window. When, however, [OK] key is pressed, the window does not shift.

Default: 50

adjustment

Sim53-8 SPF AUTO

PRESS OK KEY EXEC ERR

[OK] key or [START] Key

When the automatic adjustment result is NG, "ERR" is displayed on the value display.

MX-M182 SIMULATIONS 7-49

Main

Code

number

Print pattern Image output

0 Grid pattern (1) 1/236 1 (*1) (2) 1/128 2 (3) 1/255 3 (4) 2/254 4 Dot print (1) 1/1 5 (2) 2/2 6 (3) 1/255 7 Equal-pitch pattern (1) 1/1 8 M by N (Sub scan) (2) 1/2

9 (3) 2/2 10 Equal-pitch pattern (1) 1/1 11 M by N (Main scan) (2) 1/2 12 (3) 2/2

13 Black background

area (A4/A4R)

(1) 1%

14 (Paper F-R edge) (2) 6% 15 (3) 35% 16 Black background

area (whole surface)

No pattern

17 White background

area (whole surface)

No pattern

18 HT (whole surface) No pattern 19 Black rectangle No pattern 20 Black lead edge No pattern 21 Cross pattern No pattern

Code

number

Print pattern Image output

code

Sub

code

61 02 Laser power correction ON/OFF (Invalidity)

Enable/Disable of the LSU laser power correction during the operation is set. When [START] key is pressed, the entered set value is saved and the machine enters the sub code input standby mode.

Sim61-2 LASER PWR

1:LASER POWER

[ 0 - 1]

Code number : Mode 0 : Correction Enable

1 : Correction Disable

Note: Changing the setting does not affect the operation.

03 HSYNC output check

When this simulation is executed, the polygon motor is rotated for 30sec together with the LEND signal. "EXEC" (indicating execution) and "HSYNC" (HSYNC sensor detecting status) are displayed. Every time when the HSYNC signal is detected, "HSYNC" display is highlighted for 100ms.

（Initial window）

Sim61-3 LSU CHECK

[OK] key or [START] key

Contents Remark

Default: 0

(Execution window)

Sim61-3 LSU CHECK

HSYNC

PRESS OK KEY EXEC

63 01 Shading check

Used to display the detection level when the lamp of the white plate for shading correction is lighted. When the simulation code is entered, the initial window is displayed to urge execution. Press [OK] key or [START] key to start the simulation. The contents of the operations are as follows:

1. The mirror base unit is shifted to the white plate for shading correction.

2. The copy lamp is lighted.

3. "0" is displayed until the copy lamp light quantity is stabilized.

4. When the light quantity is stabilized, the level of 1 pixel on the CCD center which is not corrected is displayed in hexadecimal.

* The white level is displayed for about 10sec. The data update cycle is about 1sec.

5. After passing 10sec, the machine returns to the sub code input window.

Sim63-1 SHADING

PRESS OK KEY EXEC

64 01 Self print

Used to perform printing of one page disregarding the optical system status. Also when the print command is issued from the host, printing is performed. When this simulation is executed, warm-up is performed and the ready lamp is lighted. (Since, however, the optical system is invalid, initializing is not performed.) There are following twenty-one self-printable patterns. Use numeric keys to select a pattern. The selected pattern is displayed on 7-segment LED.

[OK] key or [START] key

EXEC

Sim63-1 SHADING

061

MX-M182 SIMULATIONS 7-50

Main

Sim66-1 FAX SOFT SW

ENTER FAX SOFT SW.#

( 3DIGITS ) XXX

Sim66-1 FAX SOFT SW

XXX is the input value of the soft SW number.

[OK] key [OK] key

No.XXX XXXXXXXX USE # KEY 12345678

Sim66-1 FAX SOFT SW

No.XXX XXXXXXXX

To the initial window of SIM66-1

3sec later

[CA] key : Simulation cancel [INTERRUPT] key : Sub code input window Numeric keys : Soft SW input bit No. input [OK] key : Settlement of the input value [START] key : Settlement of the input value [C] key : Input number clear for soft SW number input, disable for the following windows

code

Sub

code

Contents Remark

64 01 (*1) The grid pattern of about 1cm square is outputted.

Data are always made for A3 size. If printing is made on paper smaller than A3, the remaining data are not outputted. (Images are not formed on the drum.)

(Initial window)

Ready to copy.

100%

8 1/2×11

[OK] Key or [START] Key

Copies in progress.

100%

8 1/2×11

7SEG LED

After completion of printing one sheet

65 10 Key ACK time setting display/non-display setting

Used to set Enable/Disable of the key ACK time setting in the system settings. When this setting is set to Enable (1), the key ACK time is displayed in the system settings, allowing setting.

Sim65-10 KEY TIME

1:KEY ACK TIME

[ 0- 1]1 1

Display: Setting 0: Disable 1: Enable

[CA] key: Exit the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

11 Info lamp setting

Used to set the Info lamp brightness (PWM duty) and the kind of flashing.

Sim65-11 INFO LAMP

1:PWM DUTY 2:BLINK TYPE

[ 1- 5]

Lamp brightness 1: 100% 2: 80% 3: 60% 4: 40% 5: 20%

Kind of flashing 1: Flashing 2: Flashing 10 times, and lighting thereafter. 3: Lighting

During this simulation, Info lamp is lighted to allow checking of the brightness. [CA] key: Exit the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.

66 01 FAX soft SW setting

Default: 1

Default: Lamp brightness: 1 Kind of flashing: 1

Used to display the FAX-related soft SW on the LCD and set and change the soft SW setting with numeric keys input.

MX-M182 SIMULATIONS 7-51

Main

Sim66-2 SOFT SW

[OK] key

Sim66-2 SOFT SW

COUNTRY CODE Japan 00000000

1/34 SELECT UP DN

INITIAL

ARE YOU SURE? EXEC

Input of a value cannot be made.

INITIAL

EXEC

INITIALIZED

Sim66-2 SOFT SW

COUNTRY CODE Sweden 100101

25/34 SELECT UP DN

Simulation code input window

1sec later

[CA] key : Simulation cancel [INTERRUPT] key : Sub code input window [OK] key : Settlement [START] key : Settlement [C] key : Disable [BACK] key : Disable

U.S.A. 10110101 U.K. 10110100 Germany 00000100 France 0011110 1 Australia 00001001 China 00100110 Singapore 10011100 Malaysia 01101100 Hong Kong 01010000 Taiwan 11111110

Thailand 10101001 Middle east 1111110 1 India 01010011 Sweden 10100101 New Zealand 0111111 0 Spain 10100000 Portugal 10001011 Italy 01011001 Switzerland 10100110 Finland 0011110 0

Denmark 00110001 Norway 10000010 Netherlands 011110 11 Luxembourg 01101001 Belgium 00001111 South Africa 10011111 Czech 00101110 Slovakia 11111100 Hungary 01010001 Greece 01000110

Pohland 10001010 Russia 10111000 Brazil 00010110

Selection

Completion of execution (Highlighted during execution)

code

Sub

code

66 02 FAX soft SW initializing

Used to clear the FAX-related soft SW values except for the line signal adjustment value and the machine adjustment value and set them to the default values (which differ depending on the country code).

Contents Remark

03 FAX PWB memory check

Used to check read/write from/into the memory on the FAX PWB. The check result is displayed for each memory.

[CA] key : Simulation cancel [INTERRUPT] key : Sub code input window

Sim66-3 MEMOR CHK

1:DRAM 4:IMAGE 2:SRAM 5:PAGE 3:ROM 6:MODEM ( 1 - 6 ) X

[OK] key

Sim66-3 MEMOR CHK

DRAM

EXEC

[OK] key

Sim66-3 MEMOR CHK

DRAM CHECKING MEMORY

EXEC

*Interruption with [C] key during execution cannot be made.

Numeric keys : Item selection [OK] key : Settlement and execution of the input value [START] key : Settlement of the input value [BACK] key : Returns to the selection window. [C] key : Disable

Execution error end (Highlighted during execution)

Sim66-3 MEMOR CHK DRAM MEMORY CHECK RESULT

NG XXXXXXXX SUM

Execution normal end (Highlighted during execution)

Sim66-3 MEMOR CHK DRAM MEMORY CHECK RESULT OK

[BACK] key

NG XXXXXXXX SUM NG XXXXXXXX A-BUS NG XXXXXXXX DATA NG XXXXXXXX D-BUS NG XXXXXXXX ERASE NG XXXXXXXX IO

[BACK] key

SIM66-3 initial window

MX-M182 SIMULATIONS 7-52

Main

Sim66-4 SIGNAL OUT

SIGNAL SELECT

(1 - 35)

1:NO SIGNAL 2:33600bps(V34) 3:31200bps(V34) (1 - 35) XX

After selection with numeric keys

[OK] key

[OK] key [BACK] key

33600bps(V34) 1:MAX 2:SOFT SW. (1 - 2) X

33600bps(V34) 0dB

EXEC

33600bps(V34) PRESS BACK TO STOP

EXEC

Sim66-4 SIGNAL OUT

34:DP MAKE 35:DP BREAK

(1 - 35) XX

After pressing [OK] key

SIM66-4 initial window

[CA] key : Simulation cancel [INTERRUPT] key : Sub code input window [C] key : Input clear key : Page select Numeric keys : Number input and item selection [OK] key : Input value settlement and execution [START] key : Input value settlement [BACK] key : Signal send stop

The window is switched with the up and down keys. Input and switching the window are irrelevant. Not highlighted with an input of a value. The window is not switched, either.

When "1: NO SIGNAL" or "31: PSEUDO RNG" - "33: R.B. TONE NONE" is selected, "0dB" and "SOFT SW" are not selected. When one of these is selected, the second line is the signal name, the third and fourth lines are empty, and the fifth line is EXEC display.

1sec later

PRINT CONF.

EXEC

PRINT CONF.

EXEC

Sim66-6 PASS CODE Sim66-6 PASS CODE

Sim66-6 PASS CODE

PRINT STORED

Sim66-6 PASS CODE

NO DATA

3sec later

In case of an error

[OK] key

Sim66-7 PRINT MEMORY

PRINT STORED

PRINT IMAGE MEMORY

EXEC

NO DATA

Sim66-7 PRINT MEMORY

CAN NOT PRINT

(When there is no image memory)

[OK] key

1sec later

3sec later

[CA] key : Simulation cancel [INTERRUPT] key : Sub code input window [OK] key : Settlement [START] key : Settlement [C] key : Disable [BACK] key : Disable

code

Sub

code

66 04 Signal send mode

Used to send signals to the line and the machine speaker by setting the signal number. (Signal send is continued until interruption is instructed by pressing RETURN key.) The signal send level is selected from 0db and the soft SW values. Since the level setting is not required for 1:NO SIGNAL and 31:PSEUDO RNG

- 33:R.B.TONE NONE, the selection menu does not appear. The signal send level is returned to the soft SW

set value before execution of the mode when completing the mode.

Contents Remark

06 Confidential pass code print

Used to print the confidential ID table (confidential box number, confidential box name, confidential pass code).

07 Image memory content print

Used to print all the image data (confidential receive contents, remote send images, and images which are not sent yet) in the image memory of the FAX section. The printed images are remained in the memory after printing.

MX-M182 SIMULATIONS 7-53

Main code

Sub

code

66 10 Image memory contents clear

Used to clear all the image data (including confidential receive contents) in the image memory of the FAX section. The management table is also cleared (initialized) at the same time.

Sim66-10 IMAGE CLR

CLEAR IMAGE MEMORY

ARE YOU SURE? EXEC

[CA] key : Simulation cancel [INTERRUPT] key : Sub code input window [OK] key : Settlement [BACK] key : Simulation code input window [START] key : Settlement [C] key : Disable

11 300bps signal send

Used to send the specified signal at the speed of 300bps by setting the signal number. (Signal send is continued until interruption is instructed by pressing RETURN key.) The signal send level is selected from 0db and soft switch set values. The signal send level is returned to the sot SW set value before execution of the mode after completion of the mode.

[OK] key

After pressing [OK] key, during execution

Contents Remark

Without prints

Sim66-10 IMAGE CLR

CLEARED

[BACK] key

Simulation code input window

Sim66-10 IMAGE CLR

CLEAR IMAGE MEM.

EXEC

Completion of execution (Highlighted during execution)

With prints

Sim66-10 IMAGE CLR

CLEARED IMAGE MEM. DO POWER OFF

Power source OFF/ON

Completion of execution (Highlighted during execution)

Sim66-11 300bps SIG.

SIGNAL LEVEL 1:MAX 2:SOFT SW. ( 1 - 2 ) X

After selection with numeric keys

[OK] key

Sim66-11 300bps SIG.

1:NO SIG. 4:00000 2: 11111 5 :010101 3: 11110 6: 00001 ( 1 - 6 ) X

After selection with numeric keys

[OK] key

[CA] key : Simulation cancel [INTERRUPT] key : Sub code input window [C] key : Input clear keys : Page switch Numeric keys : Item selection [OK] key : Input value settlement and execution [START] key : Input value settlement [BACK] key : Signal send stop

Sim66-11 300bps SIG.

NO SIGNAL

EXEC

After pressing [OK] key, during execution

[OK] key

Sim66-11 300bps SIG.

OUTPUTING SIGNAL PRESS BACK TO STOP

EXEC

[BACK] key

SIM66-11 initial window

MX-M182 SIMULATIONS 7-54

Main code

Sub

code

66 13 Dial number registration

Used to perform send test and adjustments of the dial pulse and the DTMF signal. Perform send test of the dial pulse and the DTMF signal, and perform adjustments of the make time of the dial pulse and adjustments of the send level of the DTMF signal.

Contents Remark

Sim66-13 DIAL TEST

1:PULSE 10pps 2:PULSE 20pps 3:DTMF ( 1-3 ) X

After selection with numeric key

[OK] key [OK] key

Sim66-13 DIAL TEST

PULSE 10pps INPUT MAKE TIME YY ( 26-41 ) YY

After selection with numeric key

[OK] key

Sim66-13 DIAL TEST

PULSE 10pps YYms INPUT DIAL # XXXXXXXXXXXXX EXEC

Select with numeric keys and press [OK] key.

[OK] key

Sim66-13 DIAL TEST

SEND 10 pps YYms INPUT DIAL # XXXXXXXXXXXXX EXEC

After pressing [OK] key, during execution

[OK] key

Sim66-13 DIAL TEST

SENDING 10 pps YYms INPUT DIAL # XXXXXXXXXXXX EXEC

Completion of execution (Highlighted during execution)

SIM66-13 initial window

After selection with numeric key

Sim66-13 DIAL TEST

1.NormalMode

2.HandsetMode

( 1-2 ) X

When the soft SW and the SIM DTMF sound speaker are selected, "Normal" and "handset" are selected. In another case, this menu is not displayed.

The default is set to "1590." Dial input (0 - 9, *, #) When the value is great, scroll to the left. When [C] is pressed, all are cleared.

After selection with numeric key

[OK] key

[INTERRUPT] key : Sub code input window [C] key : Input clear Numeric key : Input of time and dial number and selection of an item [OK] key : Settlement and execution of an input [START] key : Settlement of an input [BACK] key : Returns to the selection window XXXXXXXX : Input dial

Sim66-13 DIAL TEST

SELECT HIGH LEVEL 1:DEFAULT 2:SOFT SW. Y ( 1-2 ) X

When "2" is selected

[OK] key

Sim66-13 DIAL TEST

INPUT LOW LEVEL DTMF SOFT SW. Y ( 0-15 ) XX

Select with numeric keys and press [OK] key.

Sim66-13 DIAL TEST

DTMF HIGH:XX LOW:YY INPUT DIAL # XXXXXXXXXXXXX EXEC

After pressing [OK] key, during execution

Sim66-13 DIAL TEST

DTMF HIGH:XX LOW:YY INPUT DIAL # XXXXXXXXXXXXX EXEC

SIM66-13 initial window

[OK] key

Completion of execution (Highlighted during execution)

Set the signal send level to 0 or to the soft SW setting value. (High group of DTMF signal send level) *1 (Low group of DTMF

signal send level)

When "1" is selected

[OK] key

The default is set to "1590." Dial input (0 - 9, *, #) When the value is great, scroll to the left. When [C] is pressed, all are cleared.

17 DTMF signal send

Used to send the DTMF signal.

Sim66-17 DTMF SIG.

1:MAX 2:SOFT SW.

( 1-2 ) X

Set the signal send level to MAX or to the soft setting value.

After selection with numeric key

[OK] key

After pressing [OK] key, during execution

Completion of execution (Highlighted during execution)

Sim66-17 DTMF SIG.

INPUT DIAL # X

EXEC

Sim66-17 DTMF SIG.

SENDING SIGNAL X PRESS BACK TO STOP EXEC

SIM66-17 initial window

MX-M182 SIMULATIONS 7-55

[OK] key

[BACK] key

Select the dial number to be sent. (1 dial)

The DTMF signal of the selected dial number is sent until the interruption command is delivered by pressing the stop key.

[CA] key : Simulation cancel [INTERRUPT] key : Sub code input window [C] key : Input clear and stop Numeric keys : Item selection, dial number input [OK] key : Input value settlement and execution [START] key : Input value settlement and execution [BACK] key : Signal send stop

Main code

Sub

code

66 21 FAX information print

Used to print the following FAX information.

Contents Remark

Sim66-21 LIST

1:USER SW. LIST 2:SOFT SW. LIST 3:SYSTEM ERROR (1 - 5) X

After selection with numeric keys

[OK] key

Sim66-21 LIST

SOFT SW. LIST

EXEC

After pressing [OK] key, during execution

[OK] key

24 FAST SRAM clear

Used to clear the FAST SRAM data.

Sim66-24 FAST CLEAR

FAST Correspond

FAST NO Correspond

INITIAL

EXEC

Sim66-24 FAST CLEAR

Not Supported

30 TEL/LIU status change check

Sim66-21 LIST

PROTOCOL MONITOR

4: 5:FAX SIMULATION

(1 - 5) X

Sim66-21 LIST

PRINT STORED

1sec later

SIM66-21 window

After pressing [OK] key, during execution

[OK] key

[CA] key : Simulation cancel [INTERRUPT] key : Sub code input window [OK] key : Settlement [START] key : Settlement [C] key : Disable [BACK] key : Disable

After selection with numeric keys

[OK] key

Sim66-24 FAST CLEAR

INITIAL

EXEC

Sim66-21 LIST

CAN NOT PRINT

Printer Error

1sec later

SIM66-21 window

[CA] key : Simulation cancel [INTERRUPT] key : Sub code input window Numeric key : Item selection [OK] key : Settlement and execution [START] key : Input value settlement and execution [BACK] key : Returns to the selection window. keys : Page switch [C] key : Disable

Completion of execution (Highlighted during execution)

Sim66-24 FAST CLEAR

INITIALIZED

1sec later

Simulation code input window

Used to display the change contents regardless of the soft SW setting when the status of the polarity inversion relay, the handset hook switch, or the external telephone hook switch is changed. The display of the changed status is remained until the interruption command is made by pressing RETURN key.

Sim66-30 TEL STAT.

EXEC

After pressing [OK] key, during execution

[OK] key

Sim66-30 TEL STAT.

HS2 :XXX HS1 :XXX RHS :XXX EXHS :XXX PRESS BACK TO STOP EXEC

XXX: ON or OFF

[BACK] key

SIM66-30 initial window

[CA] key : Simulation cancel [INTERRUPT] key : Sub code input window [OK] key : Settlement [BACK] key : Returns to the selection window [START] key : Settlement [C] key : Disable

MX-M182 SIMULATIONS 7-56

Main code

Sub

code

66 31 TEL/LIU setting

The following bit 0/1 is alternatively switched. At the same time, the target signal name is highlighted.

Sim66-31 TEL OUTPUT

1:CION 2:150VON

3:EC 4:S

(1 - 5) X

Sim66-31 TEL OUTPUT

1:CION 5:MSR

EXEC

Sim66-31 TEL OUTPUT

1:CION 5:MSR

PRESS BACK TO STOP EXEC

After selection with numeric keys

[OK] key

After pressing [OK] key, during execution

[OK] key

[BACK] key

Contents Remark

[CA] key : Simulation cancel

Sim66-31 TEL OUTPUT

5:MSR

(1 - 5) X

Selection of two or more items can be made. (The selected numbers are highlighted.) Though numeric keys is pressed in the sequence of "1 and 5" or "5 and 1," the display is made in the sequence of the normal order (1 and 5) when OK key is pressed.

[INTERRUPT] key : Sub code input window Numeric keys : Item selection [OK] key : Input value settlement and execution [START] key : Input value settlement and execution [BACK] key : Returns to the selection window keys : Page switch [C] key : Input value clear. ON when highlighted.

32 Receive data check

Used to check receive data from the line and judge whether the following receive data and the judged data number accord together or not. If they accord, "OK" is notified. If not, "NG" is notified. Judgment is made from the receive start data and the data must be accorded continuously.

After pressing

Sim66-32 RECV DATA

CHECK RECEIVE DATA

EXEC

[CA] key : Simulation cancel [INTERRUPT] key : Sub code input window [OK] key : Settlement [START] key : Settlement

[OK] key, during execution

[OK] key

Sim66-32 RECV DATA

RECEIVING

EXEC

"RECEIVING" is displayed only during receive.

[BACK] key : Simulation code input window [C] key : Disable XX : "OK/NG" is displayed

Completion of execution (Highlighted during execution)

Sim66-32 RECV DATA

RESULT XX

[BACK] key

Simulation code input window

MX-M182 SIMULATIONS 7-57

Main

CI : FNET:

EXEC

Sim66-33 SIGNAL CHK

CNG : CED : BT : DT :

EXEC

Sim66-33 SIGNAL CHK

1:CI FNET 2:CNG CED BT DT 3:Flag SDT DTMF (1 - 3) X

Sim66-33 SIGNAL CHK

Flag: SDT : DTMF:

EXEC

[OK] key

[BACK] key

[OK] key

[BACK] key

[OK] key

[BACK] key

Sim66-33 SIGNAL CHK

CI :OFF FNET:OFF

DETECT EXEC

Sim66-33 SIGNAL CHK

CNG :OFF CED :OFF BT :OFF DT :OFF

DETECT EXEC

Sim66-33 SIGNAL CHK

Flag:OFF SDT :OFF DTMF:OFF

DETECT EXEC

Sim66-33 SIGNAL CHK

After selection with numeric key

After pressing [OK] key, during execution

SIM66-33 initial window SIM66-33 initial window SIM66-33 initial window

1:CI FINET

2:CNG CED BT DT

3:Flag SDT DTMF

[CA] key : Simulation cancel [INTERRUPT] key : Sub code input window [C] key : Input clear Numeric key : Item selection [ON] key : Input value settlement and execution [START] key : Similar to OK key

Signal detection YES/NO is displayed with ON/OFF.

Type of sound Test sound Sound volume setting value

0123

1.Call sound Call sound No Sound Small Medium Large

2.Line monitor sound Communication signal sound (33600bps)

No Sound Small Medium Large

3.On-hook Communication signal sound (33600bps)

Setting disable

Small Medium Large

4.Terminating sound Read end sound No Sound Small Medium Large

5.Communication end sound Communication end sound

No Sound Small Medium Large

6.DTMF send sound DTMF send sound No Sound Small Medium Large

code

Sub

code

66 33 Signal detection check

Used to detect signals and display the result with ON/OFF.

Contents Remark

34 Communication time measurement

Used to perform a send/receive test and measure and display the time required for send/receive of the image data in the communication.

Immediately after

Sim66-34 COMM. TIME

EXEC

[CA] key : Simulation cancel [INTERRUPT] key : Sub code input window [OK] key : Settlement [BACK] key : Simulation code input window [START] key : Settlement [C] key : Disable

pressing [OK] key, the window shifts to the next one.

[OK] key

Sim66-34 COMM. TIME

COMM. TIME: xxx:xx:xx:xxxms

Simulation code input window

[BACK] key

37 Speaker sound volume adjustment

Used to adjust the speaker sound volume. During execution of this simulation, the following test sound is sent to the line and the speaker. The send level to the line is set to the soft SW setting value. The speaker sound volume can be adjusted by the operation. The type of sound can be selected among the following:

1.Call sound, 2.Line monitor sound, 3.On-hook, 4.Terminating sound, 5.Communication end sound,

6.DTMF send sound For each type of sound, the sound volume can be selected among the following: No sound, Small, Medium, Large The set value is written into each soft SW.

MX-M182 SIMULATIONS 7-58

Main

Type of sound Soft SW number

1. Sound volume of call sound SW 53-3 - 4

Sound volume of call sound (Low) SW131-5 - 8 Sound volume of call sound (Medium) SW132-1 - 4 Sound volume of call sound (High) SW132-5 - 8

2. Line monitor speaker sound volume SW 52-5 - 6

Line monitor speaker sound volume (Low) SW127-1 - 4 Line monitor speaker sound volume (Medium) SW127-5 - 8 Line monitor speaker sound volume (High) SW128-1 - 4

3. On-hook speaker sound volume SW 53-1 - 2

On-hook speaker sound volume (Low) SW130-1 - 4 On-hook speaker sound volume (Medium) SW130-5 - 8 On-hook speaker sound volume (High) SW131-1 - 4

4. Scan end speaker sound volume SW 52-1 - 2

Scan end speaker sound volume (Low) SW124-1 - 4 Scan end speaker sound volume (Medium) SW124-5 - 8 Scan end speaker sound volume (High) SW125-1 - 4

5. Communication end speaker sound volume SW 52-7 - 8

Communication end speaker sound volume (Low) SW128-5 - 8 Communication end speaker sound volume (Medium) SW129-1 - 4 Communication end speaker sound volume (High) SW129-5 - 8

6. DTMF send speaker sound volume SW 52-3 - 4

DTMF send speaker sound volume (Low) SW125-5 - 8 DTMF send speaker sound volume (Medium) SW126-1 - 4 DTMF send speaker sound volume (High) SW126-5 - 8

code

Sub

code

66 37 The following soft SW's are newly provided.

Contents Remark

The following soft SW's are not affected SW55-4 - 5 Send end sound SW55-6 - 7 Receive end sound

Sim66-37 SPEAKER

1:RINGER 2:LINE MONITOR 3:ON HOOK ( 1 - 6 ) X

Window display 1ȇRINGER 2ȇLINE MONITOR 3ȇON HOOK 4ȇSCAN FINISH 5ȇTX/RX FINISH 6ȇDTMF

After selection with numeric keys

[OK] key

Sim66-37 SPEAKER

ON HOOK 1:SMA.2:MED.3:LAR.

( 1 - 3 ) X

Sim66-37 SPEAKER

ON HOOK SMALL XX ( 1 - 15 ) YY

38 Time setting/check

Used to write/read the time (year, month, day, o'clock, minute) into/from the RTC on the FAX PWB.

After inputting

Sim66-38 DATE & TIME

DATE YEAR XXXX

(2011-2062) YY

with numeric key, press [OK] key.

[OK] key

Sim66-38 DATE & TIME

DATE MONTH XX

(1-12) YY

xx: The current year/month/day is displayed. yy: The input value is displayed.

After execution, the display shifts to the sub code input window.

[OK] key

Sim66-38 DATE & TIME

YEAR 20YY MONTH YY DAY YY EXEC

[CA] key : Simulation cancel [INTERRUPT] key : Sub code input window Numeric keys : Item selection and time input [OK] key : Settlement

MX-M182 SIMULATIONS 7-59

After selection with numeric keys

[OK] key

While [EXEC] is highlighted, a sound beeps.

[BACK] key

Press [BACK] key to stop the sound.

After inputting with numeric key, press [OK] key.

[OK] key

After inputting with numeric key.

Sim66-37 SPEAKER

ON HOOK SMALL XX ( 1 - 15 ) YY

After inputting with numeric key

Sim66-37 SPEAKER

ON HOOK SMALL PRESS BACK TO STOP EXEC

Sim66-38 DATE & TIME

xx: The current time is displayed. yy: The input value is displayed.

Sim66-38 DATE & TIME

TIME XX:XX

[OK] key

(00-59) YY

XX: The current set value is displayed.

YY: Input in the range of 1(Low) 15 (High) .

[OK] key

A sound beeps at the set sound volume. While the speaker is sounding, [EXEC] is highlighted. Press [BACK] key to stop the sound.

After inputting

with numeric DATE DAY XX

(1-31) YY

[START] key : Settlement [BACK] key : Returns to the previous window or the simulation code input window. [C] key : Input value clear

key.

[OK] key

Main

Window display Setting

range

1:CI_LEVEL_JUDGE

2 - 15

2:CI_CYCLE_MIN

1 - 254

3:CI_CYCLE_MAX

2 - 255

4:CI_COUNT

2 - 15

RES_3.3V_LEVEL_JUDGE

2 - 15

EXHS_LEVEL_JUDGE

2 - 255

Window display Setting

range

RHS_LEVEL_JUDGE

2 - 15 8:SON_TIMEOUT 1 - 127 9:WRITE -

Window display Setting

range

Sim66-52 PSEUDO RNG

PSEUDO RINGER CHK

EXEC

Sim66-52 PSEUDO RNG

PSEUDO RINGER CHK

EXEC

After pressing [OK] key, during execution

PSEUDO RINGER CHK PRESS BACK TO STOP

EXEC

[CA] key : Simulation cancel [INTERRUPT] key : Sub code input window [OK] key : Execution [BACK] key : Returns to the selection window. [START] key : Execution [C] key : Disable

[BACK] key

[OK] key

code

Sub

code

66 42 PIC program writing

Used to write the program again into the power control which is installed to the FAX BOX.

Sim66-42 PIC RELOAD

ARE YOU SURE?

EXEC

[CA] key : Simulation cancel [INTERRUPT] key : Sub code input window [OK] key : Settlement [BACK] key : Returns to the simulation code input window.

After pressing [OK] key, during execution

[OK] key

Contents Remark

Sim66-42 PIC RELOAD

ARE YOU SURE?

EXEC

During execution, [EXEC] is highlighted.

Sim66-42 PIC RELOAD

EXEC

[BACK] key

Sub code input window

Incase of writing error, "NG" is displayed.

43 PIC adjustment value writing

Used to write the adjustment value of the program into the power control which is installed to the FAX BOX.

Sim66-43 PIC ADJUST

1:CI LEVEL 2:CI CYCLE MIN 3:CI CYCLE MAX ( 1 - 9 ) X

[CA] key : Simulation cancel [INTERRUPT] key : Sub code input window [OK] key : Settlement [BACK] key : Returns to the simulation code input window.

After inputting with numeric key

[OK] key

9. When WRITE is selected

[OK] key

Sim66-43 PIC ADJUST

CI LEVEL XX

( 2 - 15 ) YY

XX: The current set value is displayed. YY: Input value

Sim66-43 PIC ADJUST

ARE YOU SURE?

EXEC

During execution, [EXEC] is highlighted.

After inputting with numeric key

[OK] key

SIM66-43 initial window

Sim66-43 PIC ADJUST

EXEC

After execution, the display shifts to the sub code input window.

[BACK] key

Incase of writing error, "NG" is displayed.

52 Pseudo ringer check

• The pseudo ringer sound is delivered both from the machine (speaker).

• This operation is continued until the interruption command is made by pressing RETURN key.

• The LCD displays the TEL/LIU status and the HOOK status.

• While the pseudo ringer is delivered, the RBT )ring back tone) is delivered to the line. The bell is ON for 1sec and OFF for 2sec.

Default: 1: 6 2: 10 3: 142 4: 3 5: 15 6: 240 7: 2 8: 20

67 50 USB reception speed adjustment

Used to set an limitation on the print data reception speed when the USB transfer speed is at full speed.

Sim67-50 USB SPEED

1:FULL SPEED

* When images are disturbed in printing through USB, change the setting and try again. [CA] key: Exits from the simulation mode. [INTERRUPT] key: Shifts to the sub code entry window.

[ 1- 4]

Fast

Slow

Display : Setting 1 : FAST 2 : NORMAL 1 3 : NORMAL 2 4 : SAFE

MX-M182 SIMULATIONS 7-60

Default: 3

[8] TROUBLE CODE LIST

1.Trouble code list

Main code Sub

code

CE 00 General network errors

01 NIC error 02 Server not found 03 Server down 04 FTP account error 05 FTP directory error 06 Email address error 09 Email over size limit 11 Scanner memory shortage 18 RTC battery error

E7 01 Duplex model memory error/ Image data error

02 LSU trouble 06 Image data decode error 10 Shading trouble (Black correction) 11 Shading trouble (White correction) 16 Abnormal laser output 91 Decode error (FAX print) 93 Data communication error (FAX scan)

F2 40 ATC sensor abnormality

64 Toner supply abnormality 70 Improper cartridge (destination error, life cycle

error) Identification error Model error Type error Destination error Data abnormality Misc error

74 CRUM chip communication error F5 02 Copy lamp lighting abnormality F6 00 FAX board communication trouble

10 FAX board trouble

80 FAX board communication trouble (Protocol)

81 FAX board communication trouble (Parity)

82 FAX board communication trouble (Overrun)

84 FAX board communication trouble (Framing)

88 FAX board communication trouble (Time out)

99 Machine - FAX language error F9 00 NNB communication trouble

H2 00 Thermistor open (MAIN)

01 Thermistor open (SUB)

H3 00 Heat roller high temperature detection (MAIN)

01 Heat roller high temperature detection (SUB)

H4 00 Heat roller low temperature detection H5 01 5 continuous POUT not-reached error

L1 00 Scanner feed trouble L3 00 Scanner return trouble L4 01 Main motor lock detection

11 Shifter motor trouble

32 PSFAN lock detection L6 10 Polygon motor lock detection L8 01 No full wave signal

U1 03 FAX board battery error U2 04 EEPROM read/write error (serial communication

error)

11 Counter check sum error (EEPROM)

Content

Main code Sub

code

U9 00 Panel board communication trouble

80 Panel board communication trouble (Protocol) 81 Panel board communication trouble (Parity) 82 Panel board communication trouble (Overrun) 84 Panel board communication trouble (Framing) 88 Panel board communication trouble (Time out) 99 Panel language error

CH ON None Door open

CH Blink None Developing cartridge not installed

Content

2.Details of trouble codes

Main

Sub

code

CE 00 Content General network errors

Detail Other network errors Check

and remedy

01 Content NIC error

Detail An error occurs in the network protocol stack

Check and remedy

02 Content Server not found

Detail The specified sever is not found. Check

and remedy

03 Content Server down

Detail The specified server is not active. Check

and remedy

04 Content FTP account error

Detail An account error occurs when logging in the

Check and remedy

Turn OFF and ON the power. Consult the network administrator to check the network server status. If the error still remains, turn OFF the power of the machine, and immediately contact the sales agent.

level. Turn OFF and ON the power. Consult the

network administrator to check the network server status. If the error still remains, turn OFF the power of the machine, and immediately contact the sales agent.

Since connection to the server is not established, the scan data cannot be sent. Check to confirm that the SMTP server setting and the destination registration of file server send scan are properly made. For the setting procedure of the SMTP server, refer to "Various servers setting." For the changing procedure of the destination of file server send scan, refer to "How to change or delete the registered destinations." For the input items of each setting, refer to the help menu of the Web screen.

Since the server is busy or the line is busy, scan data cannot be set. Wait for a while, and try sending again.

FTP server. Since connection to the server is not

established, the scan data cannot be sent. Check to confirm that the destination registration of file server send scan is properly made. For the changing procedure of the destination of file server send scan, refer to "How to change or delete the registered destinations." For the input items of each setting, refer to the help menu of the Web screen.

Details of trouble

MX-M182 TROUBLE CODE LIST 8-1

Main

Sub

code

CE 05 Content FTP directory error

Detail The designation of the directory in the FTP

Check and remedy

06 Content Email address error

Detail Improper email address Check

and remedy

09 Content Email over size limit

Detail The size of an email to be sent exceeds the

Check and remedy

11 Content Scanner memory shortage

Detail Memory shortage in scanner process of MX-

Check and remedy

12 Content LDAP number over

Detail The number of LDAP exceeds the

Check and remedy

18 Content RTC battery error

Detail The battery for RTC is low. Check

and remedy

E7 01 Content Duplex model memory error/ Image data error

Detail 1. The memory capacity for the duplex model

Cause 1. The memory capacity on the MCU PWB is

Check and remedy

server is improper. Since the directory of the FTP server

registered as the destination of file server send scan is improper, the scan data cannot be sent. Check to confirm that the registration of the destination is correct.

Since the email address registered as the destination of the email send scan is improper, scan data cannot be sent. Check to confirm that the registered destination information is correct.

limit. The size of the scan data exceeds the upper

limit of the file size set on the Web screen. Reduce the number of sheets of documents or change the upper limit value in "Send data upper limit" of the Web screen.

NB12. The memory becomes full during scanning

documents Reduce the number of sheets of documents, or change the resolution and the color mode in order to reduce the file size of the scan data, then retry sending again.

specification. The number of destinations which are the

targets of the global address search exceeds the max. number. Use a longer set of characters for search to narrow the area of search.

Replace the battery for RTC.

machine is wrong. Insufficient memory capacity.

2. Duplex setting is set for a single surface model.

wrong.

2. Setting for a single surface model is wrong.

1. Use SIM26-39 to check to confirm that the memory capacity is 128MB. If it is not 128MB, replace the MCU PWB.

2. If SIM26-04 is set to 1, change the setting to

0. If it is 0, replace the MCU PWB.

Details of trouble

Main

Sub

code

E7 02 Content LSU trouble

Detail The BD signal from the LSU cannot be

Cause LSU connector or LSU harness defect or

Check and remedy

06 Content Image data decode error

Detail Image expansion error Cause MCU PWB abnormality

Check and remedy

10 Content Shading trouble (Black correction)

Detail The CCD black scan level is abnormal when

Cause Improper connection of the CCD unit flat cable

Check and remedy

11 Content Shading trouble (White correction)

Detail The CCD white scan level is abnormal when

Cause Improper connection of the CCD unit flat cable

Check and remedy

16 Content Abnormal laser output

Detail When the laser output is stopped, HSYNC is

Cause Laser abnormality

Check and remedy

91 Content Decode error (FAX print)

Detail When image data sent from the FAX board to

Cause Connector connection trouble

Check and remedy

detected in a certain cycle. (Always OFF or always ON)

disconnection Polygon motor rotation abnormality Laser beams are not generated. MCU PWB abnormality.

Check connection of the LSU connector. Execute SIM 61-03 to check the LSU operations. Check that the polygon motor rotates normally. Replace the LSU unit. Replace the MCU PWB.

USB cable trouble Replace the MCU PWB.

Replace the USB cable.

the shading.

CCD unit abnormality MCU PWB abnormality.

Check connection of the CCD unit flat cable. Check the CCD unit.

the shading.

Dirt on the mirror, the lens, and the reference white plate Copy lamp lighting abnormality CCD unit abnormality MCU PWB abnormality (When occurred in the SPF scan position.) Improper installation of the mirror unit

Clean the mirror, the lens, and the reference white plate. Check lighting and the light quantity of the copy lamp (SIM05-03). Check the CCD unit. Check the MCU PWB.

detected.

MCU PWB abnormality. Replace the LSU.

Replace the MCU PWB.

the machine are judged as decode error:

MCU PWB abnormality Turn OFF/ON the power.

Connect the connector again. Replace the MCU PWB.

Details of trouble

MX-M182 TROUBLE CODE LIST 8-2

Main

Sub

code

E7 93 Content Data communication error (FAX scan)

Detail When data transmission from the machine to

Cause Connector connection trouble

Check and remedy

F2 40 Content ATC sensor abnormality

Detail ATC sensor value abnormality Cause Connector connection trouble

Check and remedy

64 Content Toner supply abnormality

Detail When toner near end is detected with the toner

Cause ATC sensor abnormality

Check and remedy

F2 70 Content •Improper cartridge (Destination error, life cycle

Detail •The destination of the machine differs from

Cause CRUM chip defect

Check and remedy

74 Content CRUM chip communication error

Detail An error occurs during communication

Cause CRUM chip abnormality

Check and remedy

the FAX board fails 5 times:

FAX PWB abnormality Turn OFF/ON the power.

Connect the connector again. Replace the FAX PWB.

Toner cartridge installation trouble Sensor breakdown

Connect the connector again. Install the developing unit again. Replace the developing unit with a normal one.

supply time of 50% or less. When the toner supply time exceeds 300%.

Toner supply abnormality Replace the toner cartridge.

Replace the developing unit.

error)

•Identific t ion error

•Model error

•Type error

•Destination error

•Data abnormality

•Misc error

that of the CRUM.

•The trade mark code of the CRUM differs.

•The company code of the CRUM differs.

•The boot program model code does not

coincide with the CRUM model code.

•When the CRUM type is other than genuine/

conversion/production rotation.

•The machine destination differs from the

CRUM destination.

Improper toner cartridge. Replace the toner cartridge.

between the MCU and the CRUM chip. The CRUM identification error occurs.

Developing unit disconnection MCU PWB abnormality

Replace the toner cartridge. Check installation of the developing unit. Use SIM16 to cancel. Replace the MCU PWB.

Details of trouble

Main

Sub

code

F5 02 Content Copy lamp lighting abnormality

Detail The copy lamp does not turn on. Cause Copy lamp abnormality

Check and remedy

F6 00 Content FAX board communication trouble.

Detail FAX board communication error. Cause No command can be sent from the MCU to the

Check and remedy

10 Content FAX board trouble.

Detail FAX board abnormality detection. Cause FAX controller and FAX board memory

Check and remedy

80 Content FAX board communication trouble (Protocol).

Detail A break error occurs in communication

Cause MCU PWB connector connection failure/

Check and remedy

81 Content FAX board communication trouble (Parity).

Detail A parity error occurs in communication.

Cause MCU PWB connector connection failure/

Check and remedy

82 Content FAX board communication trouble (Overrun).

Detail An overrun error occurs in communication

Cause MCU PWB connector connection failure/

Check and remedy

84 Content FAX board communication trouble (Framing).

Detail A framing error occurs in communication

Cause MCU PWB connector connection failure/

Check and remedy

Copy lamp harness abnormality CCD PWB harness abnormality.

Use SIM 5-3 to check the copy lamp operations.

When the copy lamp lights up.

Check the harness and the connector between the CCD unit and the MCU PWB.

When the copy lamp does not light up.

Check the harness and the connector between the copy lamp unit and the MCU PWB. Replace the copy lamp unit. Replace the MCU PWB.

FAX . Check connection of the FAX board.

Replace the FAX board.

abnormality. Replace the FAX board.

between the MCU and the FAX board.

Garbled data. Check connection of the FAX board.

Replace the FAX board. Reset the machine (Power OFF/ON).

between the MCU and the FAX board.

Garbled data. Check connection of the FAX board.

Replace the FAX board. Reset the machine (Power OFF/ON).

between the MCU and the FAX board.

Garbled data Check connection of the FAX board.

Replace the FAX board. Reset the machine. (Power OFF/ON).

between the MCU and the FAX board.

Garbled data. Check connection of the FAX board.

Replace the FAX board. Reset the machine (Power OFF/ON).

Details of trouble

MX-M182 TROUBLE CODE LIST 8-3

Main

Sub

code

F6 88 Content FAX board communication trouble (Time out).

Detail FAX board communication error. Cause There is no respond command from the FAX

Check and remedy

99 Content Machine - FAX language error.

Detail Discrepancy of the destination of the machine

Cause The destination of the machine differs from that

Check and remedy

F9 00 Content MX-NB12 board communication trouble.

Detail MX-NB12 print data reception error. Cause Print data cannot be received from the MX-

Check and remedy

H2 00 Content Thermistor open (MAIN)

Detail The thermistor is open.

Cause Thermistor abnormality

Check and remedy

01 Content Thermistor open (SUB)

Detail The sub thermistor is open.

Cause Sub thermistor abnormality

Check and remedy

for 30sec or more. Check connection of the FAX board.

Replace the FAX board. Reset the machine (Power OFF/ON).

and the FAX board.

of the FAX board. When installing to the machine that can install only MX-FX13.

Change the destination setting with SIM26-6. Replace the FAX board with one which. conforms to the destination of the machine.

NB12 for 3 min or more. Reset the machine (Power OFF/ON).

The fusing unit is not installed.

Control PWB abnormality Fusing section connector disconnection The fusing unit is not installed.

Check the harness and the connector between the thermistor and the PWB. Cancel the trouble with SIM 14.

The fusing unit is not installed.

Heater lamp abnormality Thermostat abnormality Main PWB abnormality

Use SIM 5-02 to check the heater lamp blinking operation.

When normally lighting.

Check the sub thermistor and its harness. Check the sub thermistor input circuit on the MAIN PWB.

When not normally lighting.

Check the lamp control circuit on the MCU PWB. Cancel the trouble with SIM 14.

Details of trouble

Main

Sub

code

H3 00 Content Heat roller high temperature detection (MAIN)

Detail The fusing temperature exceeds 245C°. Cause Thermistor abnormality

Check and remedy

01 Content Heat roller high temperature detection (SUB)

Detail The fusing temperature exceeds 245°C. Cause Sub thermistor abnormality

Check and remedy

H4 00 Content Heat roller low temperature detection

Detail When the fusing temperature is 150C° or less

Cause Thermistor abnormality

Check and remedy

Control PWB abnormality Fusing section connector disconnection.

Use SIM 5-02 to check the heater lamp blinking operation.

When the lamp blinks normally.

Check the thermistor and its harness. Check the thermistor input circuit on the control PWB.

When the lamp keeps ON.

Check the power PWB and the lamp control circuit on the MCU PWB. Cancel the trouble with SIM 14.

Heater lamp abnormality Thermostat abnormality Main PWB abnormality

Use SIM 5-02 to check the heater lamp blinking operation.

When normally lighting.

Check the sub thermistor and its harness. Check the sub thermistor input circuit on the MAIN PWB.

When not normally lighting.

Check the lamp control circuit on the MCU PWB. Cancel the trouble with SIM 14.

in 55 sec from starting warming-up. When the warm-up complete temperature is not reached in 30 sec from reaching 150C°. When the fusing temperature is less than 100C° in 20 sec from the ready state. When the fusing temperature is less than 80C° for more than 300ms in the ready state or in printing. When the fusing temperature is less than 80C° for more than 300ms in the standby mode at a low temperature.

Heater lamp abnormality Thermostat abnormality Control PWB abnormality

Use SIM 5-02 to check the heater lamp blinking operation.

When the lamp blinks normally.

Check the thermistor and its harness. Check the thermistor input circuit on the control PWB.

When the lamp does not light up.

Check for disconnection of the heater lamp and the thermostat. Check the interlock switch. Check the power PWB and the lamp control circuit on the MCU PWB. Cancel the trouble with SIM 14.

Details of trouble

MX-M182 TROUBLE CODE LIST 8-4

Sharp MX-M182, M182D, MX-M202D, M232D Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

[1] GENERAL

1. Note for servicing

[2] CONFIGURATION

1. System Configurations

[3] SPECIFICATIONS

1. Copy mode

2. Print mode

3. Scanner mode

[4] CONSUMABLE PARTS

1.Supply system table

2. Environmental conditions

3. Production number identification

[5] EXTERNAL VIEWS AND INTERNAL STRUCTURES

1. Appearance

2. Internal

3. Operation Section

4. Motor, solenoid, clutch

5. Sensor, switch

6. PWB unit

7. Cross sectional view

[6] ADJUSTMENTS

1. Adjustment item list

2. Copier adjustment

[7] SIMULATIONS

1. Entering the simulation mode

2. Canceling the simulation mode

3. List of simulations

4. Contents of simulations

[8] TROUBLE CODE LIST

1.Trouble code list

2.Details of trouble codes