R
FU-P60S-E
AIR PURIFIER
OPERATION MANUAL
ENGLISH
Free standing type
Freistehende Ausführung
Type de table / installation murale
De sobremesa / instalación en la pared
Tipo da scrivania / parete
Tafelmodel / wandmodel
LUFTREINIGER
BEDIENUNGSANLEITUNG
PURIFICATEUR D'AIR
MANUEL D'UTILISATION
PURIFICADOR DE AIRE
MANUAL DE USO
PURIFICATORE
DELL’ARIA
MANUALE OPERATIVO
LUCHTREINIGER
DEUTSCH
DEUTSCH
FRANÇAIS
ESPAÑOL
ITALIANO
*Plasmacluster is a trademark of
Sharp Corporation.
GEBRUIKSAANWIJZING
NEDERLANDS
GDBBQAP
Please read before operating your new Air Purifier
The air purifier draws in room air from its air intake, lets the air pass through a
Active Carbon Filter (deodorization filter) and a HEPA Filter (dust collection
filter) inside of the unit, then discharges the air from its air outlet. The air
purifier unit repeats this process by moving its internal fan.
As air passes through, a new HEPA Filter can remove 99.97% of dust particles, of as small as 0.3 microns. The Active Carbon Filter gradually absorbs
odour elements as they repeatedly pass through the filter. (Odour elements
are absorbed by HEPA Filter as well.)
Some odour ingredients absorbed by the filters may become separated and
may be discharged through the air outlet and result in additional odour. Depending on the usage environment, especially when the product is used in a
condition significantly more severe than household use, this odour may become strong in a shorter period than expected.
If the odour persists, then the filters are fully expended and it is necessary to
purchase the optional replacement filter.
NOTE
• The air purifier is designed to remove air-suspended dust and odour, but not harmful gases (for
example, carbon monoxide contained in cigarette smoke). If the odour sources still exist, it cannot
completely remove the odour. (for example, odours from construction materials and pet odours).
• It is suggested to open the window a bit when you are smoking in order to facilitate ventilation.
HEPA Filter
Active Carbon Filter
INFORMATION ON PROPER DISPOSAL ...
E-16
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should be followed, including the
following:
WARNING - To reduce the risk of electrical shock, fire or injury to persons:
• Read all instructions before using the air purifier.
• Use only a 220-240 volt outlet.
• Do not use the air purifier if the power cord or plug is damaged or the connection to the wall
outlet is loosened.
• Periodically remove dust from the power plug.
• Do not insert fingers or foreign objects into the intake or air outlet.
• When removing the power plug, always hold the plug and never pull the cord.
Electrical shock and/or fire from short circuit may occur as a result.
• Do not remove the power plug when your hands are wet.
• Do not use this air purifier near gas appliances or fireplaces.
• Remove the power plug from the wall outlet before cleaning the unit and when not using the
unit.
Electrical shock from bad insulation and/or fire from short circuit may occur as a result.
• If the power cord is damaged, it must be replaced by the manufacturer, its service agent,
Sharp authorized Service Centre or similarly qualified person in order to avoid a hazard.
• Do not operate when using aerosol insecticides or in rooms where there is oily residue, incense,
sparks from lit cigarettes, chemical fumes in the air or under a humid condition.
• Be cautions when cleaning the air purifier. Strong corrosive cleansers may damage the exterior.
• Only Sharp Authorized Service Centre should service this air purifier. Contact the nearest Service
Centre for any problems, adjustments, or repairs.
• The batteries must be removed from the remote control before disposal, and the batteries must be
disposed of safely.
NOTE - Radio or TV Interference
If this air purifier should cause interference to radio or television reception, try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the air purifier and radio/TV receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTIONS CONCERNING OPERATION
• Do not block the intake and air outlet.
• Do not use the unit near or on hot objects, such as stoves or heaters or where it may come into
contact with steam.
• Do not lay the unit down when using.
• Always hold the handle on the back of the main unit when moving it.
Holding the front panel when carrying may cause it to detach, thus dropping the unit and resulting in
bodily injury.
• Do not operate the unit without the filter.
• Do not wash and reuse HEPA filter.
Not only it does not improve filter performance, it may cause electric shock or malfunction.
• Clean the exterior with a soft cloth only.
The unit surface may be damaged or cracked.
In addition, the sensor may malfunction as a result.
E-2
REMOTE CONTROL LIMITATIONS
DO NOT USE THE REMOTE CONTROL IN THE FOLLOWING LOCATIONS:
• Any location where there is inverter lighting equipment or electronic spontaneous lighting
equipment
The remote control may become inoperative. In this case, move away from such lighting equipment
or change direction.
• Location exposed to direct sunlight or fluorescent.
The unit may not receive signals from the remote control.
INSTALLATION GUIDELINES
• During the operation of the product, please place the unit at least 2m away from equipments
which involve electric wave such as televisions, radios or wave clocks, in case electrical
interference occurs to such equipment.
•Avoid a location where the sensor is exposed to direct wind.
The unit may not operate properly.
•Avoid locations where curtains, etc., come into contact with the intake or air outlet.
Curtains, etc., may become dirty or a malfunction may occur.
•Avoid locations where the unit is exposed to condensation, due to drastic temperature changes.
(Use under appropriate conditions between 0 and 35˚C in the room.)
• Place on a stable surface with sufficient air circulation.
When placing the unit on a heavily carpeted area, it may cause the unit to vibrate slightly.
• Do not install when there is generation of lampblack, such as in a kitchen, etc.
The unit surface may crack or the sensor may malfunction as a result.
• Leave about 60cm of space from the wall.
The wall behind the air outlet may become dirty as time passes. When using the unit for extended
period of time in the same location, use a vinyl sheet, etc., to prevent the wall from becoming dirty. In
addition, periodically clean the wall.
ENGLISH
FILTER GUIDELINES
• Follow the instructions in this manual for correct care and maintenance of the filters.
E-3
PART NAMES
MAIN UNIT DISPLAY
Remote Control Receiver
Filter Indicator Light
SENTINEL Operation Indicator Light
Plasmacluster Indicator
Light
CLEAN-SIGN Light
AUTO Operation Indicator Light
15min. HIGH operation Indicator
Light
Pollen Mode Indicator Light
Fan Speed Indicator
Lights
OFF Timer Display Indicator Lights
Sensor Sensitivity
Select Switch
Sensor sensitivity can be
adjusted to “Normal” or
“SENSITIVE” by this
switch.
Filter Reset Button
POWER ON/OFF Button
MODE Selection Button
Temperature/Humidy Sensor
Remote Control
INCLUDED
Remote Control (1 unit)
Battery (AA battery x 2 )
• Operation manual
Front Panel
Hook
BACK
Odour Sensor
Dust Sensor(Dust Sensor Cover)
Main Unit
Filter Frame
HEPA Filter (white)
Washable Active Carbon Filter (black)
Pre-Filter
Handle
Air Outlet
Date Label
Power Cord
Power Plug
(Sharp of plug depends on country.)
E-4
PREPARATION
INSERTING BATTERIES IN THE REMOTE CONTROL
Remove the back cover
1
Press and slide the back cover to remove.
Insert batteries
2
Insert batteries with and as
shown below.
Close the back cover
3
Battery Information
• The battery life is about 1 year.
• The batteries for this remote control are for initial use only . Change the batteries
when necessary.
• Incorrect usage of the batteries may cause battery fluid leakage and/or damage.
Take care of the following when handling:
• When replacing the batteries, replace both batteries with new ones of the same
type. (Use 2 AA manganese batteries.)
• When not using the unit or remote control for an extended period, remove the
batteries.
ENGLISH
REMOTE CONTROL USE
• Operate the remote control facing the main unit
receiver.
• The signal range is about 23 feet (7m).
• Make sure there are no objects blocking the
path of the signal.
•A beep sound will be heard from the main unit
when a signal is received.
NOTE
•Avoid dropping or damaging the remote
control, using in a high humidity condition, in
direct sunlight or near a heat source.
E-5
Receiver
Transmitter
PREPARATION
FILTER INSTALLATION
To maintain the quality of the filters, they are installed in the main unit and packed in the
plastic bags. Be sure to remove the filters from the plastic bags before using the unit.
Remove the filters
1
Remove the Front
1
Panel.
Pull the bottom of the
Front Panel.
Be sure to remove the power plug from the wall outlet.
Front Panel
2
Hook
1
1
2
1
Pull out the Filter Frame and remove the Pre-Filter,
2
Active Carbon Filter and HEPA Filter.
Filter Frame
Remove the Active Carbon Filter
3
(black) and HEPA Filter (white) from
the plastic bags.
Active Carbon Filter
HEPA Filter
Pre-Filter
Pre-Filter
Active Carbon Filter
1
2
E-6
HEPA Filter
Filter Frame
Install the filters
2
Tabs
Place the HEPA Filter
1
within the Filter Frame with
the tabs facing up.
Do not install the filter backwards or
the unit will not operate properly.
Place the Active Carbon Filter
2
on top of the HEPA Filter
with the bands (2 places)
facing up.
Place the Pre-filter through
3
the bands (2 places) located
at the corners of the Active
Carbon Filter.
Insert the tabs of the pre-filter into
the associated holes of the Filter
Frame.
HEPA Filter
Filter Frame
Band
Active Carbon Filter
HEPA Filter
Filter Frame
ENGLISH
Tabs (4 places)
Band
Mount the Filter Frame to
4
the main unit.
Fill in the usage start date
5
on the Date Label.
Use the date as a guide for the
Filter Replacement schedule.
Holes
Main unit
Filter Frame
Band
Date Label
E-7
OPERATION
MAIN UNIT OPERATION
Filter Indicator Light
SENTINEL Operation Indicator Light
Clean-Sign Light
Plasmacluster Indicator Light
Main Unit Controls
• AUTO
• 15 min. HIGH
• POLLEN
• SILENT
• NORMAL
• MAX
MODE Selection Button
Power ON/OFF Button
Power ON/OFF Button
1
• Used to start operation (short beep) and stop operation (long beep)
• Plasmacluster Indicator Light and Fan Speed Indicator Light turn on/off.
• Unless unplug the power cord, the operation starts in the previous mode the unit
was operated in.
MODE Selection Button
2
• The operation mode can be switched.
AUTO operation
The fan speed is automatically switched
(HIGH*, NORMAL, SILENT) depending
on the amount of pollution in the air. The
sensors detect the pollution for efficient
air purification.
15 min. HIGH* operation
The unit will operate at HIGH* fan speed
for 15 minutes, then will operate at Auto
operation.
The operation mode is effective when
quick removal of impurities in the air is
desired.
Plasmacluster
2
1
MAX operation
The unit will operate at a fan
speed of MAX.
NORMAL operation
The unit will operate at a fan
speed of NORMAL.
POLLEN mode operation
The unit will operate at HIGH* fan speed
for 10 minutes, then will alternate
between NORMAL and HIGH for 20
minutes.
10 minutes: HIGH fan speed
20 minutes:
20 minutes: HIGH fan speed
NORMAL fan speed
SILENT operation
The unit will operate quietly
using minimal air intake.
* HIGH fan speed is an
intermediate speed
between NORMAL
and MAX.
E-8
SENTINEL Operation Indicator Light
When Plasmacluster Ion mode is ION AUTO or CLEAN mode, SENTINEL Operation is ready to be
activated, and when SENTINEL Operation is in active, the Plasmacluster Indicator Light (blue) turns on
and repeats its colour cycles between dark and light, and also the SENTINEL Operation Indicator Light
(green) turns on.
The “SENTINEL” function detects any air environment that is favourable for activation of mold, virus and
allergen using its 4 sensors for dust, odour, temperature and humidity, and it releases Plasmacluster
Ions to create an environment that controls the activity of airborne microbes.
The fan speed and amount of Plasmacluster Ions are automatically increasedÅ@during AUTO operation,
while only the amount of Plasmacluster Ions is automatically increased during manual fan control mode
and Pollen mode.
PLASMACLUSTER INDICATOR LIGHT
Plasmacluster ion operation is selected using the remote control.
Blue light
When the Plasmacluster ion operation is in Clean Mode, or in AUTO Plasmacluster Ion Mode and the air
in the room is impure, this light will be activated and the unit will operate in Clean Mode.
Green light
When the Plasmacluster ion operation is in the Ion Control Mode, or in AUTO Plasmacluster Ion Mode
and the air in the room is clean, this light will be activated and the unit will operate in Ion Control Mode.
Light off
There are no Plasmacluster ions being generated.
• The light can be turned off by using the ‘LIGHTS ON/OFF Button’ on the Remote Control. In this case,
Plasmacluster ions are generated.
(Please turn off the light when not required.)
ENGLISH
CLEAN-SIGN LIGHT
The colour changes according to the air condition.
Clean (Green) Slightly Impure (Orange) Very Impure (Red)
ABOUT THE CLEAN-SIGN
• The condition of the CLEAN-SIGN depends on the room air condition detected by the Dust and Odour
Sensor when the plug is inserted into the wall outlet.
• It is possible to have a green CLEAN-SIGN with impurities in the air at the time that the air purifier was
just introduced to the room environment. After a while, however, the base impurity rate will be adjusted
to detect room air condition correctly.
• Use the Display ON/OFF Button on the remote control to turn off the Indicator light.
DETERMINING THE BASE IMPURITY RATE
For the first 30 seconds after the power plug is inserted into the wall outlet, the unit will check the conditions of the air. If operation is set to ON during this time, the CLEAN-SIGN LIGHT will alternately flash in
green, orange and red.
FILTER INDICATOR LIGHT
Clean the Active Carbon Filter when the Filter Indicator Light is on.
(The indicator light will be activated in about 2 months, when using the unit for 24 hours a day.)
(See Page E-12)
E-9
OPERATION
REMOTE CONTROL OPERATION
POWER ON/OFF Button
• When you press the
POWER ON/OFF Button, a
short beep will sound and
operation will start in AUTO
Mode.
• Unless unplug the power
cord, the operation starts
from the previous mode the
unit was operated in.
•To stop, press the POWER
ON/OFF Button again.
A long beep will sound and
operation will stop.
Auto (Fan Speed) Button
The fan speed switches automatically depending on the
amount of impurities in the air.
Manual (Fan Speed) Button
The fan speed can be
switched among SILENT,
NORMAL and MAX settings.
15 min. HIGH Button
See page E-8
LIGHTS ON/OFF Button
Switches the Plasmacluster
Indicator Light and CLEANSIGN Light either ON or OFF.
Plasmacluster
Operations available with
the Remote Control
• AUTO
• MANUAL
• POLLEN
• OFF TIMER
• 15 min. HIGH
• LIGHTS ON/OFF
Plasmacluster Ion mode
selections
• AUTO
• CLEAN
• ION CONTROL
• OFF
Transmitter
Filter Reset Button
When the Washable Active Carbon Filter is cleaned and
reinserted into the main unit,
press the Filter Reset Button.
Pollen Mode Operation
Button
See Page E-8
Off Timer Button
The set time switches every time
the button is pressed as shown
below.
1 hour
Cancel
• The indicator light shows the
remaining time.
• The unit will stop operation
when the timer is up.
4hours
8 hours
Plasmacluster Ion Mode Selections
AUTO
When pressed, the unit will switch between Clean
Mode and the Ion Control Mode automatically depending on the amount of impurities in the air as
detected by the dust and odour sensors. Clean
Mode will operate for 1 minute when the Auto
function is selected.
(ION CONTROL)
When pressed, the unit will constantly operate in
Ion Control Mode.
The Plasmacluster Ion Indicator Light is green.
E-10
(CLEAN)
When pressed, the unit will constantly
operate in the Clean Mode, in which
the same numbers of positive and
negative ions are discharged. The
Plasmacluster Indicator Light is blue.
OFF
The generation of ions will be ceased
and the Plasmacluster Indicator Light
will go out.
CARE AND MAINTENANCE
To maintain optimum performance of this air purifier, please clean the unit including
the sensors and filters periodically.
When cleaning the unit, be sure to unplug the power cord, and never handle the plug
with wet hands. Electrical shock and/or bodily injury may occur as a result.
MAIN UNIT
Care Cycle
To prevent dirt or stains on the main unit, clean as often as necessary. If stains are allowed to
remain, they may become hard to clean.
Wipe with a dry, soft cloth
For stubborn stains or dirt, use a soft cloth dampened with warm water.
Do not use volatile fluids
Benzene, paint thinner, polishing powder, etc., may damage the surface.
Do not use detergents
Detergent ingredients may damage the unit.
Keep the unit away from water
1 month
ODOUR SENSOR / DUST SENSOR
Care Cycle
The sensitivity of the sensor will become
unstable if the odour/dust sensor is dirty
or blocked. Remove dust from the surfaces of the sensor openings using a
vacuum cleaner.
Sensor Filter
Detach the sensor filter and tap it lightly
with your hand to remove the dust. If it is
very dirty, wash it with water and then allow
it to dry thoroughly.
2 months
Hole of odour
sensor
Hole of dust sensor
Sensor Filter
It does not have a front and
a back.
FILTER CLEANING
Care Cycle
Remove the Front Panel, Clean the surface of the Pre-Filter lightly with a vacuum cleaner.
If it is contaminated heavily, remove it from the Filter Frame and wash it.
NOTE
• In case of washing, use a soft brush etc. and cold/warm
water.
• Metal brushes or scrub brushes may cause damage.
• After washing, leave it in the shade until it gets dried.
Then place it back to the frame.
• Never wash or clean the HEPA Filter using the nozzle of
a vacuum cleaner directly.
This will greatly decrease the performance of the filters.
2 months
ENGLISH
E-11
CARE AND MAINTENANCE
WASHABLE ACTIVE CARBON FILTER CARE
HAND WASH ONLY!
DO NOT TUMBLE DRY!
Care Cycle
When the Filter Indicator Light lights up,
this indicates that the filter needs to be
cleaned. If the unit is kept on 24 hours a
day then the Filter Indicator Light will be
activated in about 2 months.
The Filter Indicator Light is for reference.
Clean the filter as often as necessary
when odour persists.
Remove
1
visible dirt
with a
vacuum
cleaner.
Fill a large container up with
2
warm water, add a mild
kitchen detergent and stir.
Dilute as indicated
on the detergent
container.
Allow the filter to soak ap-
3
proximately 30 minutes before washing.
If the filter surface
is very dirty, scrub
with an old toothbrush.
CAUTION
Handle with care to
prevent damage to
the activated carbon
particles.
Rinse thoroughly with clean
4
water
Remove excess water
5
The filter will be saturated with water after rinsing. To decrease drying time, wrap the filter in
an old thick towel so that excess water can be
removed.
CAUTION
Some carbon may adhere to
the towel, but it is harmless.
Dry the filter outdoors
6
if possible in a well
ventilated area.
CAUTION
• The wet filter is heavy. Fix it securely for drying to
make sure it does not fall down.
• The filter takes longer to dry in winter, on rainy days.
Wash it on a day when the weather is good and
dry it in the sun.
Move it indoors at night to prevent freezing.
• Dry the filter outdoors in a well ventilated area. If
dried indoors, the water dripping off the filter may
soil your floor.
• Make sure that the activated carbon has not shifted
to one side inside the filter. If it has, distribute it
evenly with your fingers.
• Let the filter dry thoroughly.
If used while the filter is still moist, then the air that
is exhausted from the main unit will have an odour.
It may take 1 or 2 days to dry.
Reinstalling the Filter.
7
Reinstall the filter as shown on Page E-6,7
Once the Active Carbon Filter has
8
been cleaned, connect the power
cord to the outlet and press the Filter
Reset Button on either the Remote
Control or Main Unit.
• Once the Filter Reset Button has been activated, you will hear a beep sound that means
the unit has been reset.
• The Filter indicator light will then go out
automatically.
CAUTION
If rinsing in a container, be sure to
rinse 3 to 4 times so
that the odour is
rinsed thoroughly
from the filter.
Filter Reset Button
E-12
FILTER REPLACEMENT GUIDELINES
Depending on the usage environment, air outlet odour may become strong
after several months.
If dust or odours cannot be removed easily, replace the filters.
(Refer to HOW SHARP AIR PURIFIER WORKS E-3)
Guide for filter replacement timing
• The following filter life and replacement period is based on the condition of smoking 10
cigarettes per day and the dust collection/deodorization power is reduced by half compared
with that of new filters.
We recommend to replace the filters more frequently if the product is used in a condition
significantly severer than normal household use.
• HEPA Filter About 5 years after opening
• Active Carbon Filter About 5 years after opening
REPLACING THE FILTERS
See page E-6,7 for directions on how
1
to install the filters when replacing.
After replacing the filters:
2
Be sure to press the Filter Reset Button on either
the Remote Control or Main Unit with the power cord
connected to the outlet.
A short beep will be heard and the operation hours
stored in the memory will be reset.
The Filter Indicator Light will then go out automatically.
ENGLISH
Fill in the usage start date of the filters
3
on the Date Label
.
Replacement Filters
Model: FZ-P63SEF
• HEPA Filter : 1 unit
• Active Carbon Filter: 1 unit
Please consult your dealer for purchase of
replacement filters.
Date Label
Disposal of Filters
Please dispose of replaced filters according to the local disposal laws and regulations.
HEPA Filter materials:
• Filter: Polypropylene
• Frame: Polyester
• Microbial Control Filter: Polypropylene, Polyethylene
Active Carbon Filter Materials:
• Deodorizer: Activated charcoal
• Net: Polypropylene 60%, Polyester 40%
E-13
TROUBLESHOOTING
Before calling for repair, please review the list below, since the problem may not be a unit malfunction.
SYMPTOM
The Remote Control does not
work
Odours and smoke are not
removed
The CLEAN-SIGN Light lights
green even when the air is
impure
The CLEAN-SIGN Light lights
orange or red even when the air
is clean
The Plasmacluster Indicator
Light remains green (or blue)
and does not change
A clicking or ticking sound is
heard from the unit
The discharged air has an
aroma or odour.
REMEDY (not a malfunction)
• Have the batteries been depleted?
• Are the batteries inserted correctly?
• Is a fluorescent lighting in the room flickering due to service
life?
• Clean or Replace the filters if they appear to be heavily soiled.
(Refer to E-12,E-13)
• The air could be impure at the time the unit was plugged in.
(Refer to E-9) Pull out the plug from the electrical outlet, and
insert the plug one minute later.
• The sensitivity of the sensors become unstable when the
opening of the odour or dust sensor is dirty or is clogged.
Clean the dust around the sensor openings using a vacuum
cleaner. (Refer to E-9)
• When in Ion Control Mode ( or Clean Mode), the Plasmacluster
Indicator Light colour will not change.
• Clicking sound is emitted when the unit is in the Ion Control
Mode, and ticking sound is emitted when the unit is generating
ions.
If the sound is irritating, set the unit away from you.
• Check to see if the filters are heavily soiled.
Replace the filters.
• Plasmacluster Air Purifiers emit small traces of ozone which
may produce an odour. These ozone emissions are well below
safety levels .
The unit does not operate when
cigarette smoke is in the air.
The Filter Indicator Light
remains activated even after
replacing filter.
The Plasmacluster Indicator
Light or the CLEAN-SIGN Light
will not activate.
ERROR DISPLAY
LAMP INDICATION
The “Silent” Fan Speed Indicator Light blinks.
• Is the unit installed in a location that is difficult for the sensor to
detect cigarette smoke?
• Are the odour or dust sensor openings blocked or clogged?
(In this case, clean the openings.) (Refer to E-11)
• After replacing filters, connect the power cord to an outlet and
press the Filter Reset Button on the remote control. (Refer to
E-12)
• Check to see if the Display OFF Mode on the Remote Control
is selected. If so, press the Display ON/OFF Button on the
Remote Control to activate the indicator light.
(Refer to E-10)
REMEDY
Fan motor disconnected or abnormal.
Operation stops.
• Pressing the ON/OFF button will reset the error display, but if
error occurs again, contact the shop where you purchased the
unit.
E-14
SPECIFICATIONS
Model
Power supply
Fan
Speed
Operation
* The applicable floor surface area is appropriate for operating the unit of maximum fan speed.
• Applicable floor surface area indicates the space where a certain amount of dust particle can be
removed in 30 minutes.
Fan speed level
Rated power
Air Flow Volume
Applicable floor surface
Cord Length
Dimensions
Weight
MAX
69W
360 m
3
/hour
415mm(W)x241mm(D)x572mm(H)
FU-P60S-E
220-240V 50/60Hz
NORMAL
9.6 W
3
138 m
/hour
~46m2*
2.0m
8.5kg
SILENT
3.7 W
30 m3/hour
Standby Power
In order to operate the electrical circuits while the power plug is inserted in the wall outlet, this
product consumes about 0.8W of standby power.
For energy conservation, unplug the power cord when the unit is not in use.
ENGLISH
E-15
Attention: Your product is
marked with this symbol. It
means that used electrical
and electronic products
should not be mixed with
general household waste.
There is a separate
collection system for these
products.
A. Information on Disposal for Users (private households)
1. In the European Union
Attention: If you want to dispose of this equipment, please do not use the ordinary dust
bin!
Used electrical and electronic equipment must be treated separately and in
accordance with legislation that requires proper treatment, recovery and recycling of
used electrical and electronic equipment.
Following the implementation by member states, private households within the EU
states may return their used electrical and electronic equipment to designated
collection facilities free of charge*. In some countries* your local retailer may also
take back your old product free of charge if you purchase a similar new one.
*) Please contact your local authority for further details.
If your used electrical or electronic equipment has batteries or accumulators, please
dispose of these separately beforehand according to local requirements .
By disposing of this product correctly you will help ensure that the waste undergoes
the necessary treatment, recovery and recycling and thus prevent potential negative
effects on the environment and human health which could otherwise arise due to
inappropriate waste handling.
2. In other Countries outside the EU
If you wish to discard this product, please contact your local authorities and ask for the
correct method of disposal.
For Switzerland: Used electrical or electronic equipment can be returned free of
charge to the dealer, even if you don’t purchase a new product. Further collection
facilities are listed on the homepage of
. Information on Disposal for Business Users.
B
www.swico.ch o r www. s e n s . c h.
1. In the European Union
If the product is used for business purposes and you want to discard it:
Please contact your SHARP dealer who will inform you about the take-back of the
product. You might be charged for the costs arising from take-back and recycling.
Small products (and small amounts) might be taken back by your local collection
facilities.
For Spain: Please contact the established collection system or your local authority for
take-back of your used products.
2. In other Countries outside the EU
If you wish to discard of this product, please contact your local authorities and ask for
the correct method of disposal.
E-16
ENGLISH
SERVICE PROCEDURE / SERVICE VORGEHENSWEISE
SERVICE PROCEDURE - ONLY EFFECTIVE IN GERMANY
Dear SHARP customer,
SHARP machines are proprietary articles which are produced with precision and care according
to most modern production methods.
In case of proper handling and with considering of the instruction book, this machine will serve
you well for a long time.
Of course, a defect cannot be ruled out.
If your appliance has a warrantyable defect in the period of warranty, please contact your dealer,
where you bought the appliance. This dealer is your only contact person for any claim of warranty.
As proof for repairs during Warranty period, you need the invoice of the machine.
Please bring your defect appliances also to your dealer (where you bought the appliance) when
the warranty period is over.
SHARP ELECTRONICS (EUROPE) GMBH
Parts & Technical Service
SERVICE VORGEHENSWEISE - GILT NUR FÜR DEUTSCHLAND
Lieber SHARP-Kunde
SHARP- Geräte sind Markenartikel, die mit Präzision und Sorgfalt nach modernen
Fertigungsmethoden hergestellt werden.
Bei sachgemäser Handhabung und unter Beachtung der Bedienungsanleitung wird lhnen lhr
Gerät lange Zeit gute Dienste leisten.
Das Auftreten von Fehlern ist aber nie auszuschließen.
Sollte lhr Gerät während der Gewährleistungsfrist einen gewährleistungspflichtigen Mangel
aufweisen, so wenden Sie sich bitte an den Handelsbetrieb, bei dem Sie dieses Gerät erworben
haben, denn dieser ist lhr alleiniger Ansprechpartner für jegliche Gewährleistungsansprüche.
Als Nachweis lm Gewährleistungsfall dient lhr Kaufbeleg.
Sollte sich nach Ablauf der Gewährlelstrungsfrist ein Fehier des Gerätes zeigen, so wenden Sie
sich bitte auch in diesem Fall an den Handelsbetrieb, bei dem Sie dieses Gerät erworben
haben.
SHARP ELECTRONICS (EUROPE) GMBH
Parts & Technical Service
SHARP CORPORATION
OSAKA, JAPAN
Loading...