FP-G50J
R
AIR PURIFIER
OPERATION MANUAL
Free standing type
“Plasmacluster” and “Device of a cluster of grapes” are
trademarks of Sharp Corporation.
*The number in this technology mark indicates an
approximate number of ions supplied into air of 1 cm
3
,
which is measured around the center of a room with
the “high-density plasmacluster 7000” applicable oor
area (at 1.2 m height above the oor) at the medium
wind volume in air purifying mode, when an air purier
using the high-density plasmacluster ion evolving
device is placed close to a wall. This product is
equipped with a device corresponding to this capacity.
OM_FP-G50J_EN.indd 1 2017/01/10 16:47:14
HEPA Filter
Deodorizing Filter
Back Panel
NOTE
The air purier draws in room air from the air intake, passes the air through a Back
Panel, a Deodorizing Filter and a HEPA Filter inside of the unit, then discharges the air
through the air outlet. The HEPA Filter can remove 99.97% of dust particles as small
as 0.3 microns that pass through the lter and also helps absorb odors.
The Deodorizing Filter gradually absorbs odors as they pass through the lter.
Some odors absorbed by the lters may break down over time, resulting in additional
odor. Depending on the usage environment, especially when the product is used in
extreme environments (significantly more severe than normal household use), this
odor may become strong in a shorter period than expected. If the odor persists, the
lters should be replaced.
• The air purier is designed to remove air-suspended dust and odor, but not harmful gases (for example, carbon monoxide contained in cigarette smoke). If the source of the odor still exists, the air
purier may not completely remove the odor.
Please read before operating your new Air Purier
OM_FP-G50J_EN.indd 2 2017/01/10 16:47:15
E-1
ENGLISH
Thank you for purchasing the SHARP
Air Purier. Please read this manual carefully.
Before using this product, be sure to read the
section: “Important Safety Instructions.”
After reading this manual, keep it in a
convenient location for future reference.
For your reference, we recommend to keep
this manual in the place where you can read
at any time.
IMPORTANT SAFETY INSTRUCTIONS
.....
E-2
PART NAMES
...............................................
E-4
FILTER INSTALLATION
.............................
E-5
OPERATION
.................................................
E-6
CARE AND MAINTENANCE
.....................
E-8
TROUBLESHOOTING
..............................
E-10
SPECIFICATIONS
......................................
E-11
FOR CUSTOMER ASSISTANCE
............
E-12
CONTENTS
FEATURES
Unique Combination of Air Treatment
Technologies
Triple Filtration System + Plasmacluster
TRAPS DUST*
Pre-filter traps dust and other large
airborne particles.
DECREASES ODORS
Deodorizing filter absorbs many common
household odors.
REDUCES POLLEN & MOLD*
HEPA filter traps 99.97% of particles as
small as 0.3 microns.
FRESHENS
Plasmacluster treats the air similar to the
way nature cleans the environment by
emitting a balance of positive and negative
ions.
*When air is drawn through the lter
system.
Sensor Technology continuously monitors
air quality, and automatically adjusting
operation based on detected air purity.
OM_FP-G50J_EN.indd 1 2017/01/10 16:47:15
E-2
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
WARNING
- To reduce the risk of electrical shock, re or injury to persons:
• Read all instructions before using the unit.
• Use only a 220-240 volt outlet.
• Do not use the unit if the power cord or plug is damaged or the connection to the
wall outlet is loosened.
• Periodically remove dust from the power plug.
• Do not insert ngers or foreign objects into the intake or air outlet.
• When removing the power plug, always hold the plug and never pull the cord.
Electrical shock and/or re from short circuit may occur as a result.
• Be careful not to damage the power cord, it may cause electric shock, excess heat or
res.
• Do not remove the plug when your hands are wet.
• Do not use this unit near gas appliances or replaces.
• Remove the power plug from the wall outlet before cleaning the unit and when not
using the unit.
Electrical shock from bad insulation and/or re from short circuit may occur as a result.
• When cleaning the unit, or when the unit is not in use, be sure to unplug the unit. Electrical
shock and/or re from a short circuit may result.
• If the power cord is damaged, it must be replaced by the manufacturer, its service
agent, Sharp Approved Service Centre or similarly qualified person in order to
avoid a hazard.
• Do not operate when using aerosol insecticides or in rooms where there is oily residue,
incense, sparks from lit cigarettes, chemical fumes in the air or in very high humidity conditions, such as a bathroom.
• Be cautious when cleaning the unit. Corrosive cleansers may damage the exterior.
• Only a Sharp Authorized Service Centre should service this air purier. Contact the near-
est Service Centre for any problems, adjustments, or repairs.
• This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
NOTE
- Radio or TV Interference
If this air purier should cause interference to radio or television reception, try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the unit and radio/TV receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
OM_FP-G50J_EN.indd 2 2017/01/10 16:47:15
E-3
CAUTIONS CONCERNING OPERATION
• Do not block the intake and/or air outlet.
• Do not use the unit near or on hot objects, such as stoves or heaters or where it may
come into contact with steam.
• Do not lay the unit down when using.
• Always hold the handle on the back of the unit when moving it.
• Do not use without the lters inside the unit.
• Do not wash and reuse the HEPA lter and the deodorizing lter.
Not only does it not improve lter performance, it may cause electric shock or malfunction.
INSTALLATION GUIDELINES
• When using the unit, place it away from equipment utilizing electric waves such as
televisions or radios to avoid electrical interference.
• Avoid use in locations where furniture, fabrics or other items may come in contact
with and restrict the air intake and/or air outlet.
• Avoid use in locations where the unit is exposed to condensation or drastic
temperature changes. Appropriate conditions are when room temperature is
between 0 – 35 ºC.
• Place on a stable surface with sufcient air circulation.
When placing the unit on a heavily carpeted area, the unit may vibrate slightly.
• Avoid locations where grease or oily smoke is generated.
The unit surface may crack as a result.
• Place the unit about 30 cm(1 ft) away from the wall in order to ensure proper
airow.
The dust collecting performance will be the same even if using the unit 3cm away from
the wall, but place it as far as possible(30cm away recommended) because it may dirty
the wall or oor around.
FILTER GUIDELINES
• Follow the instructions in this manual for correct care and maintenance of the lter.
OM_FP-G50J_EN.indd 3 2017/01/10 16:47:15
E-4
PART NAMES
19
18
2
1
1
Main Unit
10
Handle
2
Air Outlet
11
Dust Sensor /
Dust Sensor Filter
3
OFF TIMER Button / OFF TIMER indicator Light (green)
LIGHT ON/OFF Button (Press 3 sec.)
12
HEPA Filter
4
MODE Button / MODE Indicator Light (green)
Plasmacluster Ion ON/OFF Button(Press 3 sec.)
13
Deodorizing Filter
14
Upper Tabs
5
CLEAN ION SHOWER Button /
CLEAN ION SHOWER indicator Light (green)
15
Back Panel (Pre-Filter)
6
POWER ON/OFF Button
16
Bottom Tabs
7
ODOR sensor
17
Power Cord
8
DUST AND ODOR SIGN
18
Plug
9
PLASMACLUSTER SIGN
19
Date Label
FRONT
BACK
17
14
15
PLASMACLUSTER SIGN
blue Plasmacluster ON
off Plasmacluster OFF
9
8
Clean
Impure
Red
Orange
Green
3 4 5 6
10
11
12
13
16
DUST AND ODOR SIGN
Indicates the air purity of the room
in 3 levels with color changes.
7
(Shape of plug depends on country.)
OM_FP-G50J_EN.indd 4 2017/01/10 16:47:18
E-5
FILTER INSTALLATION
To maintain the quality of the lter, it is installed in the main unit and packed in plastic
bag. Be sure to remove the lter from the plastic bag before using the unit.
• Do not operate the unit without the lter.
Date Label
Be sure to remove the power plug
from the wall outlet.
1
Remove the Back Panel.
2
Remove the lter from the plas-
tic bag.
3
Place the Filter within the main
unit.
Do not install the lter backwards or the
unit will not operate properly.
Upper Tabs
Pull
HEPA Filter
Deodorizing Filter
Starting date of use
. .
. .
. .. .
. .. .
FZ-F50HFE
HEPA Filter
Deodorizing Filter
FZ-F50DFE
. .. .
. .. .
. .. .
MODEL
MODEL
Push
Push
4
Replace the Back Panel to the
main unit.
5
Fill in the usage start date on the
Date Label.
Use the date as a guide for the lter re-
placement schedule.
Bottom Tabs
OM_FP-G50J_EN.indd 5 2017/01/10 16:47:21
E-6
OPERATION
AUTO SLEEP MED MAX
CLEAN AIR
START
• Select the desired fan speed.
• Unless the power cord has been unplugged,
the operation starts in the previous mode it
was operated in.
STOP
FAN SPEED
SLEEP
• The unit will operate very quietly, and the fan speed
is automatically switched depending on the amount of
impurities in the air.
DUST AND ODOR/PLASMACLUSTER SIGN go off
automatically.
Even though the indicator is off, Plasmacluster Ion is
dispersed into air unless Plasmacluster Ion is turned off by
.
NOTE
AUTO
• The fan speed is automatically switched depending on the
amount of impurities in the air. The sensors detect impurities
for efcient air purcation.
Releases high-density Plasmacluster ions and discharges strong air ow for 60 minutes.
CLEAN ION SHOWER
START
• If Plasmacluster Ion is OFF, Plasmacluster Ion will not be
released.
• When the operation nishes, the unit will return to the prior
operation mode.
It is able to change the other mode and during this
mode.
NOTE
OM_FP-G50J_EN.indd 6 2017/01/10 16:47:26
E-7
Light Control
Plasmacluster Ion ON/OFF
You can set the DUST AND ODOR/PLASMACLUSTER SIGN to OFF when their SIGN is bright.
ON
more than 3 sec.
OFF
• When the unit restarts its
operation, Light Control
resumes its setting set before
turning off.
• At Sleep Mode, Light Control
is available.
NOTE
When Plasmacluster Ion is ON, the PLASMACLUSTER SIGN will turn on. (blue)
(In operation)
ON OFF
ADJUSTMENT OF SENSOR DETECTION SENSITIVITY
Set to “Low” if the DUST AND ODOR SIGN is constantly red to reduce sensitivity, and set to “High” if
the DUST AND ODOR SIGN is constantly green to increase sensitivity.
OFF TIMER
Select the length of time you want, with the unit on. The unit automatically stops once the selected
time is reached.
CANCELLATION
• If the power ON/OFF Button is
not pushed within 8 seconds of
adjusting sensor sensitivity, the
setting will be saved automatically.
• The sensor sensitivity setting
will be saved even if the unit is
unplugged.
NOTE
1
2
3
(with the unit OFF)
High
Standard
Low
more than 3 sec.
more than 3 sec. more than 3 sec.
more than 3 sec.
OM_FP-G50J_EN.indd 7 2017/01/10 16:47:34
E-8
CARE AND MAINTENANCE
Gently remove dust from the back panel, using a vacuum
cleaner attachment or similar tool.
BACK PANEL
(Pre-lter)
To maintain optimum performance of this air purier, please clean the unit including the lter
periodically.
Be sure to disconnect the power cord from the wall outlet before performing any maintenance.
Back Panel
CAUTION
Back Panel
Do not apply excessive pressure, when scrubbing the back
panel.
NOTE How to clean hard to remove dirt
1. Add a small amount of kitchen detergent to water and soak
for about 10 minutes.
2. Rinse off the kitchen detergent with clean water.
3. Completely dry the lter in a well-ventilated area.
FILTERS
Tag
HEPA Filter
Deodorizing Filter
CAUTION
Gently remove dust from HEPA Filter and Deodorizing Filter with a vacuum
cleaner attachment or similar tool.
Do not WASH in water and DRY in the sun.
The lters are fragile, be careful not to apply too much force.
• HEPA Filter
Apply the maintenance only on the side with the tag.
Do not clean the opposite side; otherwise, the lter will be
damaged.
• Deodorizing Filter
The maintenance can be applied to the both sides.
UNIT
Wipe with a dry, soft cloth
For stubborn stains or dirt, use a soft cloth dampened with warm water.
•Do not use volatile uids
Benzine, paint thinner, polishing powder, etc., may damage the surface.
•Do not use detergents
Detergent ingredients may damage the unit.
CAUTION
OM_FP-G50J_EN.indd 8 2017/01/10 16:47:37
E-9
REPLACING THE FILTER
Replacement Filter
• Please consult your dealer for purchase of replacement lter.
• Use only lter designed for this product.
Be sure to remove the power plug from the wall outlet.
SENSORS
1. Remove the Back Panel.
2. Remove the Dust Sensor Filter.
3. If it is very dirty, wash it with water and dry
it thoroughly.
FILTER REPLACEMENT GUIDELINES
Do not wash and reuse the lter
The lter life and replacement period are based on the condition of smoking 5 cigarettes per
day and the Dust and odor collection power is reduced by half compared with that of new lter.
Filter life varies depending on the room environment, usage, and location of the unit.
We recommend to replace the lter more frequently if the product is used in a condition significantly severer than normal household use.
Disposal of Filter
Please dispose of the replaced lter according to the local disposal laws and regulations.
See page E-5 for directions on how to
install the lter when replacing.
Replacement timing
About 2 years after operating
Date Label
Model:FZ-F50HFE Model:FZ-F50DFE
• HEPA Filter : 1 unit • Deodorizing Filter : 1 unit
HEPA Filter materials :
•Filter : Polypropylene
•Frame : Polyester
Deodorizing Filter materials :
•Polypropylene, Polyester, Activated charcoal
Gently remove dust from the odor sensor,
using a vacuum cleaner attachment or similar
tool.
Odor sensor
Dust sensor
Dust sensor
lter
Odor sensor
OM_FP-G50J_EN.indd 9 2017/01/10 16:47:39
E-10
TROUBLESHOOTING
SYMPTOM REMEDY (not a malfunction)
Odors and smoke are not removed.
• Replace the lters if they appear to be heavily soiled.
(Ref. E-9)
The DUST AND ODOR SIGN
illuminates green even when the
air is impure.
• The air could be impure at the time the unit was plugged in.
Unplug the unit, wait one minute, and plug the unit in again.
The DUST AND ODOR SIGN illuminates orange or red even when
the air is clean.
• Sensor operation is affected if the Dust and odor sensor
openings are dirty or clogged. Gently clean the Dust and odor
sensor openings.
(Ref. E-9).
A clicking or ticking sound is heard
from the unit.
• Clicking or ticking sounds may be audible when the unit is
generating ions.
The discharged air has an odor.
• Check to see if the lters are heavily soiled.
• Clean or replace the lters.
• Plasmacluster Air Puriers emit small traces of ozone which
may produce an odor.
The unit does not operate properly
when cigarette smoke is in the air.
• Is the unit installed in a location that is difcult for the sensor to
detect cigarette smoke?
• Is the dust and odor sensor opening blocked or clogged?
(In this case, clean the opening.) (Ref. E-9)
The
DUST AND ODOR SIGN
is
turned off.
• Check to see if the Lights OFF Mode selected.
Press
for 3 seconds to light On. (Ref. E-7)
•
Check to see if the SLEEP mode is selected.
The DUST AND ODOR/PLASMACLUSTER SIGN are turned off
automatically after the SLEEP mode is selected.
The DUST AND ODOR SIGN lights
change colour frequently.
• The DUST AND ODOR SIGN lights automatically change
colours as impurities are detected by the Dust and odor sensor.
Before calling for service, please review the Troubleshooting chart below, since the problem may not
be a unit malfunction.
OM_FP-G50J_EN.indd 10 2017/01/10 16:47:40
E-11
Power supply 220-240V 50-60Hz
Fan
Speed
Operation
Fan Speed Adjustment MAX MED SLEEP
*1
Rated Power 47W 16W 4.0~5.5W
Fan Speed 306m
3
/hour 186m3/hour 48~90m3/hour
Recommended Room Size ~40m
2 *2
High density Plasmacluster ion recommended room size
~23m
2 *3
Cord Length 2.0m
Dimensions 383mm(W)x209mm(D)x540mm(H)
Weight 5.1kg
*1 The fan speed is automatically switched depending on the amount of impurities in the air.
*2 Size of a room which is appropriate for operating the unit at maximum fan speed.
• It indicates the space where a certain amount of dust particles can be removed in 30 minutes
(JEM1467).
*3 Size of a room in which approximately 7000 ions can be measured per cubic centimeter in the
center of the room (at a height of approximately 1.2 meters from the oor) when the product is
placed next to a wall and run at the MED operation position.
Standby Power
In order to operate the electrical circuits while the power plug is inserted in the
wall outlet, this product consumes about 1.0W of standby power.
For energy saving, unplug the power cord when the unit is not in use.
SYMPTOM REMEDY (not a malfunction)
AUTO RESTART
After a power failure, automatically
resume the operation when the
power recovers.
Auto Restart can be set.
• Even when the plug is unplugged or the breaker is thrown
during the operation, the operation resumes at the previous
operation mode and settings if the power recovers.
SPECIFICATIONS
ON OFF
(with the unit OFF) (with the unit OFF)
If the , , lamp Lights up
for 10 seconds, the setting is completed.
(simultaneously for more than 3 sec.) (simultaneously for more than 3 sec.)
OM_FP-G50J_EN.indd 11 2017/01/10 16:47:43
E-12
FOR CUSTOMER ASSISTANCE
Congratulations on Your Purchase!
This Sharp product is warranted against faults in material and manufacture for the
period as stated in the table below.
If service is required during the warranty period, please contact your nearest Sharp
Approved Service Centre. These repairs would be carried out at no charge to the
owner, subject to the conditions specified herein.
This warranty does not extend to defects or injuries caused by or resulting from causes
not attributable to faulty parts or the manufacture of the product, including but not
limited to, defect or injury caused by or resulting from misuse, abuse, neglect, lack of
maintenance, accidental damage, improper voltage, liquid spillage, vermin infestation,
software, or any alterations made to the product which are not authorised by Sharp.
Please retain your sales documentation, as this should be produced to validate a
warranty claim. This warranty is in addition to and in no way limits, varies or excludes
any implied rights and remedies under any relevant legislation in the country of sale.
WARRANTY PERIODS
Home Theatre Projector 12 months
Audio/Home Theatre 12 months
Microwave Oven 12 months
Steam Oven 12 months
Refrigerator 24 months
DVD/Blu-ray 12 months
Air Conditioner 60 months
Portable Air Conditioner 12 months
LCD Television 36 months
Air Purifier 12 months
IMPORTANT NOTICE: This warranty applies only to products sold in Australia&New Zealand
SHARP CORPORATION OF
AUSTRALIA PTY. LIMITED
ABN 40 003 039 405
2 Julius Avenue
North Ryde NSW 2113
SHARP CORPORATION OF
NEW ZEALAND LIMITED
59 Hugo Johnston Drive
Penrose, Auckland
WARRANTY
Consumer Electronic Products
SPform 040 (AUGUST 2011)
Australian customers: Our goods come with guarantees that cannot be excluded
under the Australian Consumer Law. You are entitled to a replacement or refund
for a major failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired or replaced
if the goods fail to be of acceptable quality and the failure does not amount
to a major failure. The criteria of a major failure is defined in the Australian
Consumer Law. Should you require any assistance with a major failure please
contact Sharp Customer Care.
This warranty does not cover transportation to and from the Sharp Approved Service
Centre. Goods presented for repair may be replaced by refurbished goods of the same
type rather than being repaired. Refurbished parts may be used to repair the goods.
The repair of your goods may result in the loss of user generated data, please ensure
that you have saved this data elsewhere prior to repair.
(excluding lamps and air filters)
FOR CUSTOMER ASSISTANCE
FOR LOCATION ENQUIRIES WITHIN
NEW ZEALAND
REGARDING YOUR LOCAL
SHARP CORPORATION OF NEW ZEALAND LIMITED
VISIT OUR WEBSITE AT
SHARP CUSTOMER SERVICES
TELEPHONE: 09 573 0111
FACSIMILE: 09 573 0113
SPform019(AUGUST 2011)
SHARP APPROVED SERVICE CENTRE
www.sharp.net.nz
CONTACT YOUR SELLING DEALER/RETAILER
OR CALL
FOR LOCATION ENQUIRIES WITHIN
AUSTRALIA
REGARDING YOUR LOCAL
SHARP APPROVED SERVICE CENTRE
VISIT OUR WEBSITE AT
www.sharp.net.au
OR CALL SHARP CUSTOMER CARE
1300 135 022
SHARP CORPORATION OF AUSTRALIA PTY LTD
(LOCAL CALL COSTS APPLY WITHIN AUSTRALIA)
OM_FP-G50J_EN.indd 12 2017/01/10 16:47:44
E-13
FOR CUSTOMER ASSISTANCE
FOR LOCATION ENQUIRIES WITHIN
NEW ZEALAND
REGARDING YOUR LOCAL
SHARP CORPORATION OF NEW ZEALAND LIMITED
VISIT OUR WEBSITE AT
SHARP CUSTOMER SERVICES
TELEPHONE: 09 573 0111
FACSIMILE: 09 573 0113
SPform019(AUGUST 2011)
SHARP APPROVED SERVICE CENTRE
www.sharp.net.nz
CONTACT YOUR SELLING DEALER/RETAILER
OR CALL
FOR LOCATION ENQUIRIES WITHIN
AUSTRALIA
REGARDING YOUR LOCAL
SHARP APPROVED SERVICE CENTRE
VISIT OUR WEBSITE AT
www.sharp.net.au
OR CALL SHARP CUSTOMER CARE
1300 135 022
SHARP CORPORATION OF AUSTRALIA PTY LTD
(LOCAL CALL COSTS APPLY WITHIN AUSTRALIA)
OM_FP-G50J_EN.indd 13 2017/01/10 16:47:44
Printed in Thailand
TINS-B009KKRZ 17B- 1
SHARP CORPORATION OF AUSTRALIA PTY.LTD.
A. B. N. 40 003 039 405
2 JULIUS AVENUE, NORTH RYDE, N.S.W. 2113
P.O.BOX 84, MACQUARIE PARK. N.S.W 2113
SHARP CORPORATION OF NEW ZEALAND LIMITED
59 HUGO JOHNSTON DRIVE PENROSE, AUCKLAND
OM_FP-G50J_EN.indd 14 2017/01/10 16:47:44
Loading...