
®
ELECTRONIC PRINTING CALCULATOR
CALCULATRICE IMPRIMANTE ÉLECTRONIQUE
CALCULADORA IMPRESORA ELECTRONICA
OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE MANEJO
In U.S.A. only:
WARNING – FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly
approved by the manufacturer could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
SHARP CORPORATION
OPERATIONAL NOTES
To insure trouble-free operation of your SHARP calculator, we recommend the following:
1. The calculator should be kept in areas free from
extreme temperature changes, moisture, and dust.
2. A soft, dry cloth should be used to clean the
calculator. Do not use solvents or a wet cloth.
3. Since this product is not waterproof, do not use it or
store it where fluids, for example water, can splash
onto it. Raindrops, water spray, juice, coffee,
steam, perspiration, etc. will also cause malfunction.
4. If service should be required, use only a SHARP
servicing dealer, a SHARP approved service facility
or SHARP repair service.
5. If you pull out the power cord to cut electricity
completely, the presently stored tax rate will be
cleared.
OPERATING CONTROLS
ON
OFF
• P P•
“OFF”: Power OFF
“•”: Power ON. Set to the non print mode.
“P”: Power ON. Set to the print mode.
“P•IC”: Power ON. Set to the print and item count
* The built-in LCD backlight turns on when the calcula-
tor’s power is on and turns off when the power is off.
Note: The counter has a maximum capacity of 3 digits
(up to ±999). If the count exceeds the maximum, the counter will recount from zero.
2
1
3
F
“3 2 1 0”: Presets the number of decimal places in the
“F”: The answer is displayed in the floating decimal
system.
“A”: The decimal point in addition and subtraction
entries is automatically positioned to the 2nd digit
from the lowest digit of entry number. Use of the
add mode permits addition and subtraction of
numbers without entry of the decimal point. Use of
add mode and decimally correct answers will be
printed.
Set Decimal Selector to 2.
4
9 = 0.444 ... , 5 9 = 0.555 ...
5/4 0.44 0.56
➞
Note: The decimal point floats during successive cal-
culation by the use of
If the decimal selector is set to “F” then the answer is
always rounded down (
POWER SWITCH; PRINT / ITEM
IC
COUNT MODE SELECTOR:
mode.
For addition or subtraction, each time
pressed, 1 is added to the item counter, and
each time
• The count is printed when the calculated
result is obtained.
• Pressing of
ter.
0
A
answer.
, and will automatically override the
ROUNDING SELECTOR:
is pressed, 1 is subtracted.
, clears the coun-
DECIMAL / ADD MODE SELECTOR:
9 5 9
4
0.44 0.55
or .
).
is
Afin d’assurer un fonctionnement sans ennui de la
calculatrice SHARP, veuillez prendre les précautions
suivantes:
1. Ne pas laisser la calculatrice dans les endroits
sujets à de forts changements de température, à
l’humidité, et à la poussière.
2. Pour le nettoyage de la calculatrice, utiliser un
chiffon doux et sec. Ne pas utiliser de solvants ni
un chiffon humide.
3. Cet appareil n’étant pas étanche, il ne faut pas
l’utiliser ou l’entreposer dans des endroits où il
risquerait d’étre mouillé, par exemple par de l’eau.
La pluie, l’eau brumisée, l’humidité, le café, la
vapeur, la transpiration, etc. sont à l’origine de
dysfonctionnements.
4. Si une réparation s’avérait nécessaire, confier
l’appareil à un distributeur agréé par SHARP et
assurant l’entretien, à un service d’entretien agréé
par SHARP, ou à un centre d’entretien SHARP.
5. Si la fiche du cordon d’alimentation est débranchée
de telle sorte que l’alimentation électrique se trouve
complètement coupé e, le taux de taxe
présentement mis en mémoire est effacé.
OFF
• P P•
“OFF”: Mise hors tension.
“•”: Mise sous tension. Pour choisir le mode de
“P”: Mise sous tension. Pour choisir le mode de
“P•IC”: Mise sous tension. Pour choisir le mode
* Le rétro-éclairage de l’écran à cristaux liquides
intégré s’allume quand la calculatrice est mise sous
tension et s’éteint quand elle est mise hors tension.
Note: La capacité du compteur est de 3 chiffres
maximum (jusqu’à ±999). Si le compte dépasse
ce maximum, le compteur repartira de zéro.
2
1
3
F
“3 2 1 0”: Il préétablit le nombre de décimales dans le
“F”: Le résultat est affiché dans le système à virgule
flottante.
“A”: Lors des opérations d’addition et de soustraction,
le point décimal est automatiquement placé à
gauche du 2ème chiffre en partant de la droite. Le
mode addition permet l’addition et la soustraction
de nombres sans que la frappe du point décimal
soit nécessaire. L’emploi des
annule automatiquement le mode addition et
permet l’impression du résultat, le point décimal
étant placé à l’endroit approprié.
Placer le sélecteur de décimale sur 2.
4
9 = 0.444 ... , 5 9 = 0.555 ...
5/4 0.44 0.56
Note: La virgule flotte durant un calcul successif en
utilisant
Si le sélecteur de décimale est sur la position “F”, le
résultat est toujours arrondi à la valeur inférieure (
PRÉCAUTIONS
LES COMMANDES
ON
INTERRUPTEUR; SÉLECTEUR DE
IC
MODE D’IMPRESSION /
COMPTAGE D’ARTICLES:
non impression.
impression.
d’impression et de comptage d’articles.
Lors des additions et des soustractions,
chaque fois que l’on appuie sur
est ajoutée au compteur d’articles et chaque
fois que l’on appuie sur
retranchée.
• Le compte est imprimé lorsque le résultat
calculé est obtenu.
• Le compteur revient à zéro en agissant sur
, .
0
A
SÉLECTEUR DE MODE DÉCIMAL /
ADDITION:
résultat.
SÉLECTEUR D’ARRONDI:
9 5 9
4
➞
0.44 0.55
ou .
, une unité est
, et
, une unité
).
EL-1192BL
Caution!
The socket outlet shall be installed near the
equipment and shall be easily accessible.
Attention!
La prise de courant murale doit être installée à
proximité de l’appareil et doit être facilement
accessible.
Aviso!
El tomacorriente debe estar instalado cerca del
equipo y debe quedar bien accesible.
PRINTED IN CHINA / IMPRIMÉ EN CHINE / IMPRESO EN CHINA
NOTAS AL MANEJARLA
A fin de que su calculadora SHARP funcione sin
averías, le recomendamos lo siguiente:
1. Evite dejar la calculadora en ambientes en que
haya cambios de temperatura, humedad y polvo
bastante notables.
2. Al limpiar la calculadora, utilice un paño suave y
seco. No use disolventes ni tampoco un paño
húmedo.
3. Debido a que este producto no es a prueba de
agua, no deberá ser utilizado o guardado en
lugares donde pudiera ser salpicado por líquidos,
por ejemplo agua. Gotas de lluvia, salpicaduras de
agua, jugos o zumos, café, vapor, transpiración,
etc. también perjudican el funcionamiento del
producto.
4. Si necesita reparar esta unidad, diríjase sólo a un
distribuidor SHARP, a un centro de servicio
autorizado por SHARP o a un centro de
reparaciones SHARP.
5. Si desconecta el cable de alimentación para
desconectar completamente la electricidad, la tasa
de impuesto almacenada actualmente se borrará.
CONTROLES DE FUNCIONAMIENTO
ON
OFF
• P P•
“OFF”: Apagado (OFF)
“•”: Encendido (ON). Fija el modo de no
“P”: Encendido (ON). Fija el modo de impresión.
“P•IC”: Encendido (ON). Fija el modo de impresión y
* La retroiluminación de la LCD incorporada se
enciende y se apaga cuando se conecta y
desconecta respectivamente la alimentación de la
calculadora.
Nota: El contador tiene una capacidad de un máximo
de 3 cifras (hasta ±999). Si la cuenta excede el
máximo, el contador vuelve a contar partiendo
de cero.
2
1
3
F
“3 2 1 0”: Prefija el número de lugares decimales de la
“F”: La respuesta aparecerá en la exhibición en el
sistema decimal flotante.
“A”: El punto decimal en los registros de suma y resta
se coloca automáticamente en la segunda cifra a
partir de la cifra más baja del número registrado.
Utilizando el modo de suma se pueden sumar y
restar números sin registrar el punto decimal. El
uso de
modo de suma e imprime las respuestas
decimalmente correctas.
Fija el selector decimal en 2.
4
9 = 0.444 ... , 5 9 = 0.555 ...
5/4 0.44 0.56
➞
Nota: El punto (= coma) decimal flota mientras se
hacen cálculos sucesivos usando
Si el selector decimal se coloca en “F”, la respuesta
siempre se redondea por defecto (
INTERRUPTOR DE CORRIENTE;
IC
SELECTOR DEL MODO DE
IMPRESION / MODO PARA
CONTAR ARTICULOS:
impresión.
de cuenta de artículos.
En las sumas o restas, cada vez que se
apriete
artículos, y cada vez que se apriete
restará 1.
• La cuenta queda impresa cuando se obtiene
el resultado calculado.
• Al apretar
contenido del contador.
0
A
respuesta.
SELECTOR DE REDONDEO:
se añadira 1 al contador de
SELECTOR DEL MODE DE
DECIMAL / SUMA:
, y anula automáticamente el
4
00CT(TINSZ0410EHZZ)
se
, se borra el
9 5 9
0.44 0.55
o .
).
CHANGE SIGN KEY:
Changes the algebraic sign of a number (i.e., positive
to negative or negative to positive).
MARKUP KEY:
Used to perform mark-ups, percent change and automatic add on/discount.
RECALL AND CLEAR MEMORY KEY
RECALL MEMORY KEY
STORE KEY:
This key is used to store the tax rate.
• A maximum of 4 digits can be stored (decimal point is
not counted as a digit).
• Only one rate can be stored. If you enter a new rate,
the previous rate will be cleared.
TAX-INCLUDING KEY
PRE-TAX KEY
DISPLAY SYMBOLS:
M : Memory symbol
Appears when a number is in the memory.
– : Minus symbol
Appears when a number is negative.
E : Error symbol
Appears when an overflow or other error is
detected.
G : Grand total memory symbol
Appears when a number is in the grand total
memory.
TAX+ : Tax-including symbol
Appears when the total calculated includes
tax.
TAX– : Pre-tax symbol
Appears when the total calculated excludes
tax.
TAX : Tax rate symbol
Appears when the tax rate is set.
INK ROLLER REPLACEMENT
If printing is blurry even when the ink roller is in the
proper position, replace the roller.
Ink roller: Type EA-781R-BK (Black)
1) Set the power switch to OFF.
2) Remove the printer cover. (Fig. 1)
3) Remove the ink roller by turning it counterclockwise
4) Install the correct color new ink roller and press it in
5) Put back the printer cover.
Cleaning the printing mechanism
If the print becomes dull after long time usage,
clean the printing wheel according to the following
procedures:
1) Remove the printer cover and the ink roller.
2) Install the paper roll and feed it until it comes out of
3) Put a small brush (like a tooth brush) lightly to the
4) Put back the ink roller and the printer cover.
Notes: • Never attempt to turn the printing belt or restrict its
Type EA-781R-RD (Red)
WARNING
APPLYING INK TO WORN INK ROLLER OR USE
OF UNAPPROVED INK ROLLER MAY CAUSE
SERIOUS DAMAGE TO PRINTER.
and pulling it upward. (Fig. 2)
the correct position. Make sure that the ink roller is
securely in place. (Fig. 3)
Fig. 1
the front of the printing mechanism.
printing wheel and clean it by pressing
movement while printing. This may cause incorrect
printing.
• Do not rotate the printing mechanism manually, this
may damage the printer.
.
PAPER ROLL REPLACEMENT
Never insert paper roll if torn. Doing so will cause
paper to jam.
Always cut leading edge with scissors first.
1) Insert the leading edge of the paper roll into the
opening. (Fig. 1)
2) Turn the power on and feed the paper by pressing
. (Fig. 2)
3) Lift the attached metal paper holder up and insert
the paper roll to the paper holder. (Fig. 3)
TOUCHE DE CHANGEMENT DE SIGNE:
Permet de changer le signe algébrique d’un nombre
(c.à.d. de positif à négatif ou de négatif à positif).
TOUCHE DE MAJORATION:
Cette touche sert à effectuer les hausses de prix, le
changement de pourcentage et les majorations/rabais
automatiques.
TOUCHE DE RAPPEL ET D’EFFACEMENT
DE LA MÉMOIRE
TOUCHE DE RAPPEL DE LA MÉMOIRE
TOUCHE ENREGISTREMENT:
Cette touche permet de mettre en mémoire un taux de
taxe.
• 4 chiffres, au plus, peuvent être mis en mémoire (le
point décimal ne compte pas pour un chiffre).
• Un seul taux peut ê tre mis en mémoire.
L’enregistrement d’un nouveau efface le précédent.
TOUCHE DE TAXE INCLUE
TOUCHE DE PRÉTAXE
SYMBOLES AFFICHÉS:
M : Symbole de mémoire
Visualisé lorsqu’un nombre est mis en
mémoire.
– : Symbole de soustraction
Visualisé lorsque le nombre est négatif.
E : Symbole d’erreur
Visualisé en cas d’erreur ou de dépassement
de capacité.
G : Symbole de mémoire du total général
Apparaît lorsqu’un nombre se trouve dans la
mémoire du total général.
TAX+ : Symbole de taxe incluse
Visualisé losque le total calculé inclut la taxe.
TAX– : Symbole de prétaxe
Visualisé losque le total calculé exclu la taxe.
TAX : Symbole de taux de taxe
Visualisé aussi losque le taux de taxe est
réglé.
REMPLACEMENT DU CYLINDRE ENCREUR
Si l’impression est floue bien que le cylindre encreur
soit dans la position convenable, remplacer ce cylindre.
Cylindre encreur: Type EA-781R-BK (Noir)
AVERTISSEMENT:
LE FAIT D’APPLIQUER DE L’ENCRE A UN
CYLINDRE ENCREUR ABIME, OU D’UTILISER UN
CYLINDRE ENCREUR NON-APPROUVE PEUT
CAUSER DE GRAVES DEGATS A L’IMPRIMANTE.
1) Placer l’interrupteur sur la position OFF.
2) Retirer le couvercle de l’imprimante. (Fig. 1)
3) Retirer le cylindre en le tournant dans le sens
contraire des aiguilles d’une montre et en le tirant
vers le haut. (Fig. 2)
4) Installer le cylindre encreur neuf et pousser la
manette du cylindre encreur. Vérifier que le cylindre
encreur est bien en place. (Fig. 3)
5) Remettre en place le couvercle de l’imprimante.
Nettoyage du mécanisme d’impression
Si l’impression devient faible après une longue
période d’utilisation, nettoyer la roue imprimante en
suivant les instructions ci-dessous:
1) Retirer le couvercle de l’imprimante et le cylindre
encreur.
2) Mettre le rouleau de papier en place et faire
avancer le papier jusqu’à ce qu’il sorte par l’avant
du mécanisme d’impression.
3) Placer une petite brosse (telle qu’une brosse à
dents) sur la roue imprimante et la nettoyer en
appuyant sur
4) Remettre le cylindre encreur et le couvercle de
l’imprimante en place.
Remarques: • Pendant l’impression, ne tentez pas de tourner
Type EA-781R-RD (Rouge)
Fig. 2
.
la courroie d’impression ni d’en empêcher le
mouvement. Cela peut facilement provoquer
une erreur d’impression.
• Eviter de faire tourner la roue imprimante à la
main, l’imprimante pourrait être endommagée
de cette manière.
REMPLACEMENT DU ROULEAU DE PAPIER
Ne tentez pas d’introduire le papier s’il est déchiré.
En procédant ainsi, vous risquez un bourrage.
Avant tout, coupez soigneusement le début de la
bande au moyen d’une paire de ciseaux.
1) Engagez l’extrémité du rouleau de papier dans
l’ouverture. (Fig. 1)
2) Mettez l’appareil sous tension et faites avancer le
papier en appuyant sur
3) Soulevez le support métallique pour papier et
introduisez le rouleau de papier dans le support
pour papier. (Fig. 3)
. (Fig. 2)
TECLA DE CAMBIO DE SIGNO:
Cambia el signo algebraico de un número (es decir, de
positivo a negativo o de negativo a positivo).
TECLA DE USO MULTIPLE:
Se usa para llevar a cabo aumentos, cambios de
porcentaje y recargos/descuentos automáticos.
TECLA DE TOTAL Y BORRADO DE
MEMORIA
TECLA DE TOTAL PARCIAL EN MEMORIA
TECLA DE ALMACENAMIENTO:
Esta tecla se utiliza para almacenar el tipo de
impuesto.
• Se podrá almacenar un máximo de 4 dígitos (la coma
decimal no se cuenta como un dígito).
• Sólo se podrá almacenar un tipo. Si introduce un
nuevo tipo, el tipo anterior se borrar.
TECLA DE INCLUSIÓN DE IMPUESTOS
TECLA DE ANTES DE IMPUESTOS
SIMBOLOS DE LA EXHIBICION:
M : Símbolo de memoria
Aparece cuando un número se almacena en la
memoria.
– : Símbolo menos
Aparece cuando el número es negativo.
E : Símbolo de error
Aparece cuando se detecta un error o se
supera la capacidad.
G : Símbolo del total global de la memoira
Aparece cuando un número está en la
memoria de total global.
TAX+ : Símbolo de inclusión de impuesto
Aparece cuando el total calculado incluye
impuesto.
TAX– : Símbolo de antes de impuesto
Aparece cuando el total calculado excluye
impuesto.
TAX : Símbolo de tipo de impuesto
Aparece cuando se establece el tipo de
impuesto.
CAMBIO DEL RODILLO ENTINTADOR
Si la impresión queda borrosa aunque esté bien
colocado el rodillo entintador, reemplace el rodillo.
Rodillo entintador: Tipó EA-781R-BK (Negro)
ADVERTENCIA:
ECHANDO TINTA EN UN RODILLO ENTINTADOR
ROTO O USANDO UN RODILLO ENTINTADOR
NO AUTORIZADO PUEDE CAUSAR DETERIOROS
GRAVES EN LA IMPRESORA.
1) Poner el interruptor de corriente en “OFF”.
2) Sacar la tapa de la impresora. (Fig. 1)
3) Mover levemente el botón del rodillo entintador
hacia usted (en la dirección de la flecha) y luego
quitarlo. Tener cuidado para que el rodillo
entintador no se trabe debajo del estuche. (Fig. 2)
4) Instalar el nuevo rodillo entintador y empujar hacia
dentro el botón del rodillo entintador. Asegurarse
de que el rodillo entintador quede colocado
firmemente en su lugar. (Fig. 3)
5) Poner de nuevo en su lugar la tapa de la impresora.
Red
Rouge
Rojo
Limpieza del mecanismo de impresión
Si la impresión se debilita después de usar la
calculadora durante un largo tiempo, limpiar la
rueda de impresión de acuerdo con el siguiente
procedimiento:
1) Quitar la tapa de la impresora y el rodillo entintador.
2) Instalar el rollo de papel y hacerlo avanzar hasta
que salga por la parte delantera del mecanismo de
impresión.
3) Apoyar un cepillo pequeño (similar a un cepillo de
dientes) ligeramente sobre la rueda de impresión y
limpiarla apretando
4) Volver a colocar el rodillo entintador y la tapa de la
impresora.
Notas: • Nunca intente girar la correa de impresión ni limitar
su movimiento durante la impresión. Esto puede
causar una impresión incorrecta.
• Tratar de no girar la rueda de impresión manual-
mente, de lo contrario dañará la impresora.
Tipó EA-781R-RD (Rojo)
Fig. 3
.
Black
Noir
Negro
CAMBIO DEL ROLLO DEL PAPEL
Nunca introduzca un rollo de papel roto. Esto
causará atascos del papel.
Corte siempre en primer lugar el borde anterior.
1) Introduzca el borde del papel del rollo de papel en
la abertura. (Fig. 1)
2) Conecte la alimentación y haga avanzar el papel
apretando
3) Levante el soporte metálico para papel incorporado
e introduzca el rollo de papel en el soporte. (Fig. 3)
. (Fig. 2)
GRAND TOTAL MODE SELECTOR:
“GT”: This selector will accumulate the following:
(“✱ +” will be printed.)
1. Addition and subtraction totals obtained with
.
2. Product and quotient totals obtained with
or .
3. Answers obtained with
“•”: Neutral
PAPER FEED KEY
LAST DIGIT CORRECTION KEY
GRAND TOTAL KEY:
Prints and clears the “GT” memory contents.
NON-ADD / SUBTOTAL KEY:
Non-add – When this key is pressed right after an
Subtotal – Used to get subtotal(s) of additions and/or
Clear – This key also serves as a clear key for the
Clear entry – When pressed after a number and
TOTAL KEY:
When pressed after
addition and subtraction with “✱”.
EQUAL KEY:
Gives the results of multiplication and division and
performs repeat calculations with a constant.
Multiplication:
The calculator will automatically remember the first
number entered (the multiplicand) and
Division:
The calculator will automatically remember the second
number entered (the divisor) and
entry of a number in the Print mode, the
entry is printed on the left-hand side with
“#”.
This key is used to print out numbers not
subjects to calculation such as code, date,
etc.
subtractions. When pressed following
or , the subtotal is printed with “◊” and
the calculation may be continued.
CLEAR/CLEAR ENTRY KEY:
calculation register and resets an error condition.
before a function, clear the number.
or , prints the total of
or .
instruction.
instruction.
SÉLECTEUR DE MODE DE TOTAL
GÉNÉRAL:
“GT”: Ce sélecteur accumulera ce qui suit:
(“✱ +” sera imprimé.)
1. Les totaux d’addition et de soustraction
obtenus avec
2. Les totaux de produit et de quotient obtenus
avec
3. Les résultats obtenus avec ou .
“•”: Neutre, GT OFF (arrêt)
TOUCHE DE MONTÉE DE PAPIER
TOUCHE DE CORRECTION DU DERNIER
CHIFFRE:
TOUCHE DE TOTAL GÉNÉRAL:
Imprime le contenu de la mémoire du total général “GT”
et l’efface.
TOUCHE DE NON ADDITION / TOTAL PARTIEL:
Non addition –
Lorsqu’on agit sur cette touche juste après
l’ introduction d’un nombre dans le mode
d’impression, l’entrée est imprimée à gauche avec
“#”.
Cette touche sert à imprimer des nombres qui ne
sont pas sujets au calcul tels que les codes, les
dates, etc.
Total partiel –
Sert à obtenir le(s) total(aux) partiel(s) des additions
et/ou des soustractions. Lorsqu’on agit sur cette
touche à la suite de
imprimé conjointement avec “
continuer.
TOUCHE EFFACEMENT /
D’EFFACEMENT DES ENTREES:
Effacement – Cette touche sert également de touche
d’effacement des registres de calcul et annule une
condition d’erreur.
Effacement des entrées – Efface un nombre qui a été
introduit avant l’utilisation d’une touche de fonction.
TOUCHE TOTAL:
Utilisée après une touche
d’une addition ou d’une soustraction avec le symbole
“✱”.
TOUCHE SIGNE ÉGAL:
Donne le résultat de multiplications, de divisions et
effectue des calculs répétés avec une constante.
Multiplication:
La calculatrice rappelle automatiquement le premier
nombre introduit (le multiplicande) ainsi que l’instruction
.
Division:
La calculatrice rappelle automatiquement le deuxième
nombre introduit (le diviseur) ainsi que l’instruction
ou .
.
ou , le total partiel est
◊
” et le calcul peut
, , elle imprime le total
SELECTOR DEL MODO DE TOTAL
GLOBAL:
“GT”: Este selector hará que se acumule lo siguiente:
(Se imprimirá “✱ +”.)
1. Totales de suma y resta obtenidos con
2. Totales de productos y cocientes obtenidos
3. Resultados obtenidos con
“•”: Posición neutra, total global, desactivada.
TECLA DE AVANCE DEL PAPEL
TECLA DE CORRECCION DE LA ULTIMA CIFRA:
TECLA DE TOTAL GLOBAL:
Imprime y borra el contenido de la memoria de total
global “GT”.
TECLA DE NO SUMA / TOTAL PARCIAL:
No suma –
Cuando se aprieta esta tecla inmediatamente
después de haber ingresado un número en el modo
de impresión, el número registrado se imprime a la
izquierda, junto con “#”.
Esta tecla se usa para imprimir números que no
están sujetos a cálculos como, por ejemplo,
códigos, fechas, etc.
Total parcial –
Se usa para obtener uno o varios totales parciales
de sumas y/o restas. Cuando se aprieta a
continuación de
parcial junto con “
cálculos.
TECLA DE BORRADO /
BORRADO DE ENTRADA:
Borrado – Esta tecla también sirve de tecla de borrado
para los registros de cálculos y anula un estado de
error.
Borrado de entrada – Cuando se aprieta después de
un número y antes de una función, borra el número.
TECLA TOTAL:
Wher Cuando se aprieta después
total de la suma y resta con “✱”.
TECLA IGUAL:
Muestra el resultado de la multiplicación y división
realiza cálculos repetidos con una constante.
Multiplicación:
La calculadora retendrá automáticamente el primer
factor registrado (el multiplicando) y la instrucción
División:
La calculadora retendrá automáticamente el segundo
factor registrado (el divisor) y la instrucción
.
con
o .
o , se imprimirá el total
◊
”, pudiéndose seguir con los
o .
, , imprime el
Fig. 1 Fig. 3Fig. 2
.
DO NOT PULL PAPER BACKWARDS AS THIS
MAY CAUSE DAMAGE TO PRINTING MECHANISM.
ERRORS
There are several situations which will cause an
overflow or an error condition. When this occurs, “E”
will be displayed. The contents of the memory at the
time of the error are retained.
If an “0䡠E” is displayed at the time of the error, “– – – –
– – –” will be printed in red and
clear the calculator.
Error conditions:
1. When the integer portion of an answer exceeds 12
digits.
2. When the integer portion of the contents of the
memory exceeds 12 digits.
(Ex.
3. When any number is divided by zero. (Ex. 5
999999999999 1 )
)
must be used to
SPECIFICATIONS
Operating capacity: 12 digits
Power source:
AC: 120V, 60Hz
Calculations:
Four arithmetic, constant multiplication and division,
power, add-on, tax, repeat addition and subtraction,
reciprocal, grand total, item count calculation,
markup, memory, etc.
PRINTING SECTION
Printer: Mechanical printer
Printing speed: Approx. 2.6 lines/sec.
Printing paper:
57mm (2-1/4") – 58mm (2-9/32") wide
80mm (3-5/32") in diameter (max.)
Operating temperature:
0°C – 40°C (32°F – 104°F)
Power consumption: 5.2 mA
Dimensions:
200 mm (W) × 251 mm (D) × 62 mm (H)
.
.
(7-7/8" (W) × 9-7/8" (D) × 2-7/16" (H))
Weight: Approx. 910 g (2.01 Ib.)
Accessories:
1 paper roll, 2 ink rollers (installed), and operation
NE PAS TIRER LE PAPIER EN ARRIERE, CAR
CELA POURRAIT ENDOMMAGER LE MÉCANISME IMPRIMANT.
ERREURS
Il existe plusieurs cas qui entraînent un dépassement
de capacité ou une situation d’erreur. Si cela se
produit, “E” sera affiché. Le contenu de la mémoire au
moment de l’erreur est préservé.
Si un “0䡠E” s’affiche au moment de l’erreur, “– – – – – –
–” s’imprime en rouge et il faut utiliser
l’erreur.
Conditions d’erreur:
1. Lorsque la partie entière d’un résultat dépasse 12
chiffres.
2. Lorsque la partie entière du nombre en mémoire
excède 12 chiffres.
(Ex.
3. Lorsqu’un nombre est divisé par zéro. (Ex. 5
0
999999999999 1 )
)
FICHE TECHNIQUE
Capacité de travail: 12 chiffres
Alimentation:
CA: 120V, 60Hz
Calculs:
Quatre opérations arithmétiques, multiplication et
division par une constante, élévation à une puissance, majoration, taxe, additions et soustraction
successives, inverse, total général, comptage
d’articles, hausse, calcul en mémoire, etc.
SECTION IMPRESSION
Imprimante: Imprimante mécanique
Vitesse d’impression: Env. 2,6 lignes/s
Papier d’impression:
Largeur: 57 mm – 58 mm
Diamètre (maxi.): 80 mm
Température: 0°C – 40°C
Consommation: 5,2 mA
Dimensions:
200 mm (L) × 251 mm (P) × 62 mm (H)
Poids: Env. 910 g
Accessoires:
1 rouleau de papier, 2 cylindres encreurs (installé),
et mode d’emploi
pour effacer
NO TIRAR DEL PAPEL HACIA ATRAS PUES
PUEDE OCASIONAR DAÑOS AL MECANISMO
DE IMPRESION.
ERRORES
Existen diversos casos en los que ocurre un exceso de
capacidad o una condición de error. Al producirse esto,
aparecerá “E”. Los contenidos de la memoria, en el
momento del error, quedan retenidos.
Si, al ocurrir el error, se visualiza el símbolo “0䡠E”, se
imprimirá en rojo “– – – – – – –” y se deberá usar
para borrar la calculadora.
Condiciones de error:
1. Cuando la parte entera de un resultado excede las
12 cifras.
2. Cuando la parte entera de los contenidos de la
memoria supera las 12 cifras.
(Ej.
3. Cuando se divide un número cualquiera por un
0
999999999999 1 )
divisor de cero. (Ej. 5
0 )
ESPECIFICACIONES TECNICAS
Capacidad de cálculo: 12 cifras
Alimentación de corriente:
CA: 120V, 60Hz
Cálculos:
Las cuatro operaciones aritméticas, multiplicaciones y divisiones por constante, potencia,
recargos, Impuestos, sumas y restas consecutivas,
recíprocos, total global, cuenta de artículos,
aumento, memoria, etc.
SECCION DE LA IMPRESORA
Impresora: Impresora mecánica
Velocidad de impresión: Aprox. 2,6 líneas/seg.
Papel de impresión:
57 mm – 58 mm de ancho,
80 mm de diámetro (máx.)
Temperatura: 0°C – 40°C
Potencia: 5,2 mA
Dimensiones:
200 mm (An) × 251 mm (P) × 62 mm (Al)
Peso: Aprox. 910 g
Accesorios:
1 rollo de papel, 2 rodillos entintadores (instalado),
y manual de manejo
EL-1192BL(U1C)-1
➀

CALCULATION EXAMPLES
1. Set the decimal selector as specified in each
example.
The rounding selector should be in the “5/4” position
unless otherwise specified.
2. The grand total mode selector should be in the “•”
position (off position) unless otherwise specified.
3. The print / item count mode selector should be in
the “P•IC” position unless otherwise specified.
4. Press
5. If an error is made while entering a number, press
prior to beginning any calculation.
or and enter the correct number.
1. Régler le sélecteur de décimale tel que spécifié
2. Le sélecteur de mode de grand total doit être placé
3. Sauf indication contraire, le sélecteur d’impression /
4. Appuyez sur
EXEMPLES DE CALCULS
dans chaque exemple.
Le sélecteur d’arrondi, doit être placé sur la position
“5/4” sauf indication contraire.
à la position “•” (position arrêt) sauf indication
contraire.
comptage d’articles doit être placé sur la position
“P•IC”.
avant tout calcul.
5. En cas d’erreur à l’introduction d’un nombre,
appuyer sur
ou et introduire le nombre
correct.
REPEAT ADDITION AND SUBTRACTION /
ADDITION ET SOUSTRACTION SUCCESSIVES /
REPETICION DE SUMAS Y RESTAS
123 + 123 + 123 + 456 – 100 – 100 =
Operation
Opération
Operación
Display
Affichage
Exhibición
Print
Impression
Impresión
0
2
1
3
F
ADDITION AND SUBTRACTION WITH ADD MODE /
ADDITION ET SOUSTRACTION AVEC MODE D’ADDITION /
SUMA Y RESTA CON MODO DE SUMA
A
12.45 + 16.24 + 19.35 – 5.21 =
*11245 12.45 12.45 +
123 123. 123.+
246. 123.+
369. 123.+
456 825. 456.+
100
725. 100.–
625. 100.–
*1 : was not used in the entries.
*1 : La
*1 : La
625. 002
625.✱
MIXED CALCULATIONS / CALCUL COMPLEXE / CALCULOS MIXTOS
0
A
2
1
3
5.=
F
B. 5 × 2 + 12 =
A. (10 + 2) × 5 =
10 10. 10.+
2
5
12. 2.+
12. 12.×
60. 60.✱
EJEMPLOS DE CALCULOS
1. Colocar el selector decimal según se especifica en
cada ejemplo.
El selector de redondeo debe estar en la posición
“5/4” salvo que se especifique lo contrario.
2. El selector de modo de total global debe estar en la
posición “•” (posición de desconexión) salvo que se
especifique lo contrario.
3. El selector de impresión / cuenta de artículos deber
estar en la posición “P•IC” salvo que se especifique
lo contrario.
4. Pulse
cálculo.
5. Si se hace un error al ingresar un número, apretar
1624
28.69 16.24 +
1935 48.04 19.35 +
521
42.83 5.21 –
42.83 002
n’a pas été utilisée dans les entrées.
no ha sido usada en los registros.
5 5. 5.×
2
10. 10.✱
10. 10.+
12 22. 12.+
22. 002
antes de empezar cualquier
o e ingresar el número correcto.
42.83 ✱
2.=
22.✱
0
A
2
1
3
PERCENT PRORATION / DISTRIBUTION PROPORTIONNELLE
PERCENT PRORATION / DISTRIBUTION PROPORTIONNELLE EN POURCENTAGE /
DISTRIBUCION PROPORCIONAL DE PORCENTAJE
● Calculate the percentage of each of the parts to
the whole.
● Calculer le pourcentage que chaque article
représente par rapport au tout.
● Calcular el porcentaje de cada artículo.
*2: Press
*2: Effacer le contenu de la mémoire (
to clear the memory before starting a memory calculation.
) avant de procéder à un calcul avec
mémoire.
*2: Apretar
para cancelar la memoria antes de empezar a efectuar un cálculo con
memoria.
Expenses
Dépenses %
Gastos
$123 (a)
456 (b)
789 (c)
(D) (d)
*
123 123.00 123.00 +
456
789 1’368.00 789.00 +
123
456
2
579.00 456.00 +
003
8.99 8.99 % (a)
M
8.99
M
33.33
M
33.33
F
1,368.00 ✱ (D)
123.=
8.99 +M
456.=
33.33 % (b)
33.33 +M
789 789.=
M
0
A
2
1
3
F
57.68
57.68
M
57.68 % (c)
57.68 +M
100.00◊M (d)
M
100.00
M
100.00
ITEM COUNT CALCULATION / CALCUL DE COMPTE D’ARTICLES / CALCULO DE CUENTA DE ARTICULOS
100.00 ✱M
3
F
0
A
2
1
Bill No. Number of bills Amount
Facture n° Nbre de factures Montant
N° de factura Cantidad de facturas Importe
1 1 $100.55
2 1 $200.00
3 1 $200.00
4 1 $400.55
0
A
2
1
3
F
5 1 $500.65
Total (a) (b)
100.55 100.55 100.55 +
200
300.55 200.00 +
500.55 200.00 +
400.55
500.65
901.10 400.55 +
1’401.75 500.65 +
005 (a)
1’401.75 1,401.75 ✱ (b)
GRAND TOTAL / TOTAL GÉNÉRAL / TOTAL GLOBAL
100 + 200 + 300 =
+) 300 + 400 + 500 =
+) 500 – 600 + 700 =
Grand total / Total
général / Total global
CONSTANT / CALCULS AVEC CONSTANTE / CONSTANTES
A. 62.35 × 11.11 =
62.35 × 22.22 =
62.35 62.35 62.35 ×
11.11
692.7085 692.7085 ✱
22.22 22.22 =
1’385.417 1,385.417 ✱
11.11 =
2
1
3
F
POWER / PUISSANCE / POTENCIA
2
3
F
A. 5.252 =
5.25 5.25 5.25 ×
5.25 =
27.56 27.56 ✱
PERCENT / POURCENTAGE / PORCENTAJES
2
3
A. 100 × 25% =
100 100. 100.×
25 25.%
25.00 25.00 ✱
F
100 100. 100.+
0
A
B. 11.11 77.77=
÷
÷
22.22 77.77=
11.11 11.11 11.11 ÷
77.77
77.77 =
0
A
2
1
3
F
÷
0.14285714285 0.14285714285 ✱
200
300
300 300. 300.+
400
22.22 22.22 =
500
0.28571428571 0.28571428571 ✱
500 500. 500.+
600
0
A
1
0
A
2
1
3
F
700
B. 53 =
300. 200.+
600. 300.+
003
600. 600.✱+
G
G
700. 400.+
G
1’200. 500.+
G
003
1’200. 1,200.✱+
G
G
100. 600.–
G
600. 700.+
G
003
600. 600.✱+
G
5 5. 5.×
5.=
2’400. 2,400.✱✱
25. 25.✱
25.=
125. 125.✱
MEMORY / MÉMOIRE / MEMORIA
A. 46 × 78 =
÷
+) 125 5 =
–)72× 8=
Total
B. (123 + 45) × (456 – 89) =
0
A
2
1
3
F
5 5. 5.×
25. 5.×
0
A
2
1
3
F
5.=
125. 125.✱
46 46. 46.×
78
M
3’588.
25.
576.
3’037.
M
M
M
M
M
0
A
1
÷
B. 123 ÷ 1368 = (%)
123 123. 123
.
0
A
2
1
3
F
÷
1368 1,368.%
125 125.
5
72 72.
8
8.99 8.99 ✱
78.=
3,588.+M
.
÷
125
5.=
25.+M
72.×
8.=
576.–M
3,037.◊
M
123 123.
45
456
89
45.
456.
367.
367.
168.
61’656.
168.
M
M
M
M
M
M
123.+M
45.+M
456.+
89.–
367.×
168.◊
M
168.=
M
M
61,656.✱
168.✱M
RECIPROCAL / INVERSES / RECIPROCOS
0
A
2
1
1
=
7
7 7. 7
1. 7
3
F
.
÷
.
÷
7.=
0.14285714285 0.14285714285 ✱
ADD-ON AND DISCOUNT / MAJORATION ET RABAIS / RECARGOS Y DESCUENTOS
A. 5% add-on to 100. / Majoration de 5% de 100./
Un 5% de recargo sobre 100.
100 100. 100.×
5
105.00 105.00 ✱
MARKUP AND MARGIN
Markup and Profit Margin are both ways of calculating
percent profit.
– Profit margin is percent profit vs. selling price.
– Markup is percent profit vs. cost.
– Cost is the cost.
– Sell is the selling price.
– GP is the gross profit.
– Mkup is the percent profit based on cost.
– Mrgn is the percent profit based on selling price.
To find Knowing Operation
Pour trouver Quand on connaîtOpération
Para encontrar Sabiendo Operación
Mrgn Sell, Cost Cost
Mkup Sell, Cost Sell Cost
Sell Cost, Mrgn Cost Mrgn
Cost Sell, Mrgn Sell Mrgn
Sell Cost, Mkup Cost Mkup
Cost Sell, Mkup Sell Mkup
Sell
0
2
1
3
F
5.%
Increased amount
5.00
Majoration
Incremento
New amount
Total majoré
Nueva cantidad
HAUSSE ET MARGE BÉNÉFICIAIRE
Le calcul des majorations et des marges bénéficiaires
sont deux façons de calculer un pourcentage de profit.
– La marge bénéficiaire est un pourcentage de profit
par rapport au prix de vente.
– La majoration est un pourcentage de profit par
rapport au prix d’achat.
– Cost est le prix d’achat.
– Sell est le prix de vente.
– GP est le bénéfice brut.
– Mkup est le bénéfice par rapport au coût.
– Mrgn est le bénéfice par rapport au prix de vente.
Ex./Ex./Ej.
Cost $200
Sell $250
GP $50
Mkup 25%
Mrgn 20%
B. 10% discount on 100. / Rabais de 10% sur 100./
A
Un 10% de descuento sobre 100.
100 100. 100.×
10
PERCENT CHANGE / VARIATION EN POUR CENT / CAMBIO PORCENTUAL
● Calculate the dollar difference (a) and the percent change (b) between two
yearly sales figures $1,500 in one year and $1,300 in the previous.
● Calculer la différence en dollars (a) et la variation en pour cent (b) entre deux
prix. 1.500 $ pour cette année et 1.300 $ pour l’année précédente.
● Calcular la diferencia en dólares (a) y el cambio porcentual (b) entre dos cifras
de ventas anuales, $1.500 en un año y $1.300 en el año anterior.
1500 1’500.00 1,500.00 +
1300
–10.%
–10.00
90.00 90.00 ✱
INCREMENTO PORCENTUAL Y MARGEN
Tanto la función del incremento porcentual como la del
margen de beneficio son formas de calcular el beneficio
porcentual.
– El margen de beneficio es el beneficio porcentual con
respecto al precio de venta.
– El incremento porcentual es el beneficio porcentual
con respecto al coste.
– Cost es el coste.
– Sell es el precio de venta.
– GP es el beneficio bruto.
– Mkup es el beneficio porcentual basado en el coste.
– Mrgn es el beneficio porcentual basado en el precio
de venta.
200 200. 200
20
250.00 ✱ Sell
50.00 50.00 GP
200.00 1,300.00 –
15.38 15.38 % (b)
2
1
3
F
Discount
Remise
Descuento
Net amount
Montant net
Cantidad neta
2
1
3
F
.
÷
Cost
20.%M Mrgn
2
1
3
F
200.00 ✱ (a)
TAX RATE CALCULATIONS / CALCULS DE TAXE / CALCULOS CON EL TIPO DE IMPUESTO
EXAMPLE 1: Set a 5% tax rate.
Calculate the tax on $800 and calculate the total including tax.
EXEMPLE 1: Règle une taxe de 5%.
Calcule la taxe sur $800 et calcule le total incluant la taxe.
EJEMPLO 1: Establezca un tipo de impuesto del 5%.
Calcule el impuesto sobre $800 y calcule el total incluyendo el
impuesto.
5 5.
0
A
5.000
800
840. 840
. . .
5.000 %
. . .
800
40
.
.
.
In U.S.A.:
LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer
purchaser that this Sharp brand product (the “Product”), when shipped in its
original container, will be free from defective workmanship and materials,
and agrees that it will, at its option, either repair the defect or replace the
defective Product or part thereof with a new or remanufactured equivalent at
no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to
the additional excluded item(s) set forth below nor to any Product the
exterior of which has been damaged or defaced, which has been subjected
to improper voltage or other misuse, abnormal service or handling, or which
has been altered or modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser
should follow the steps set forth below and provide proof of purchase to the
servicer.
The limited warranty described herein is in addition to whatever implied
warranties may be granted to purchasers by law. ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF
PURCHASE SET FORTH BELOW. Some states do not allow limitations on
how long an implied warranty lasts, so the above limitation may not apply to
you.
Neither the sales personnel of the seller nor any other person is authorized
to make any warranties other than those described herein, or to extend the
duration of any warranties beyond the time period described herein on behalf
of Sharp.
The warranties described herein shall be the sole and exclusive warranties
0
A
0
A
granted by Sharp and shall be the sole and exclusive remedy available to the
purchaser. Correction of defects, in the manner and for the period of time
described herein, shall constitute complete fulfillment of all liabilities and
responsibilities of Sharp to the purchaser with respect to the Product, and
shall constitute full satisfaction of all claims, whether based on contract,
negligence, strict liability or otherwise. In no event shall Sharp be liable, or
in any way responsible, for any damages or defects in the Product which
were caused by repairs or attempted repairs performed by anyone other than
an authorized servicer. Nor shall Sharp be liable or in any way responsible
for any incidental or consequential economic or property damage. Some
states do not allow the exclusion of incidental or consequential damages, so
the above exclusion may not apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY
ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
Your Product : Electronic Calculator
Warranty Period for this One (1) year parts and labor from date of
Product : purchase.
Additional Items Excluded Any consumable items such as paper, mainfrom Warranty Coverage : tenance cartridge, ink cartridges supplied with
Where to Obtain Service : At a Sharp Authorized Servicer located in the
What to do to Obtain Service : Ship (prepaid) or carry in your Product to a
TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP.
the Product or to any equipment or any hardware, software, firmware, fluorescent lamp,
power cords, covers, rubber parts, or peripherals
other than the Product.
United States. To find out the location of the
nearest Sharp Authorized Servicer, call Sharp
toll free at 1-800-BE-SHARP.
Sharp Authorized Servicer. Be sure to have proof
of purchase available. If you ship or mail the
Product, be sure it is packaged carefully.
In Canada:
Sharp Electronics of Canada Ltd. (hereinafter called “Sharp”) gives the following express
warranty to the first consumer purchaser for this Sharp brand product, when shipped in its
original container and sold or distributed in Canada by Sharp or by an Authorized Sharp
Dealer:
Sharp warrants that this product is free, under normal use and maintenance, from any defects
in material and workmanship. If any such defects should be found in this product within the
applicable warranty period, Sharp shall, at its option, repair or replace the product as specified
herein.
This warranty shall not apply to:
(a) Any defects caused or repairs required as a result of abusive operation, negligence,
accident, improper installation or inappropriate use as outlined in the owner’s manual.
(b) Any Sharp product tampered with, modified, adjusted or repaired by any party other than
Sharp, Sharp’s Authorized Service Centres or Sharp’s Authorized Servicing Dealers.
(c) Damage caused or repairs required as a result of the use with items not specified or
approved by Sharp, including but not limited to software, paper and batteries.
(d) Any replacement of accessories, glassware, consumable or peripheral items required
through normal use of the product including but not limited to batteries, AC adapters,
ribbons, correction tapes, ink rollers, cables, printwheel, or paper.
(e) Any cosmetic damage to the surface or exterior that has been defaced or caused by
normal wear and tear.
(f) Any damage caused by external or environmental conditions, including but not limited to
transmission line/power line voltage or liquid spillage.
(g) Any product received without appropriate model, serial number and CSA/CUL markings.
(h) Any products used for rental purposes.
(i) Any installation, setup and/or programming charges.
Should this Sharp product fail to operate during the warranty period, warranty service may be
obtained upon delivery of the Sharp product together with proof of purchase and a copy of this
LIMITED WARRANTY statement to an Authorized Sharp Service Centre or an Authorized
Sharp Servicing Dealer.
This warranty constitutes the entire express warranty granted by Sharp and no other dealer,
service centre or their agent or employee is authorized to extend, enlarge or transfer this
warranty on behalf of Sharp. To the extent the law permits, Sharp disclaims any and all liability
for direct or indirect damages or losses or for any incidental, special or consequential damages
or loss of profits resulting from a defect in material or workmanship relating to the product,
including damages for the loss of time or use of this Sharp product or the loss of information.
The purchaser will be responsible for any removal, reinstallation, transportation and insurance
costs incurred. Correction of defects, in the manner and period of time described herein,
constitute complete fulfillment of all obligations and responsibilities of Sharp to the purchaser
with respect to the product and shall constitute full satisfaction of all claims, whether based on
contract, negligence, strict liability or otherwise.
Calculator without printer 1 year
Calculator with printer 6 months
Pocket Computer 1 year
To obtain the name and address of the nearest Authorized Sharp Service Centre
SHARP ELECTRONICS OF CANADA LTD
335 Britannia Road East
Mississauga, Ontario
L4Z 1W9
(905) 568-7140 or 1 (877) SHARP-CC
Web site: www.sharp.ca
LIMITED WARRANTY
Personal Office Products
Congratulations on your purchase!
WARRANTY PERIODS
or Dealer, please contact:
SHARP ELECTRONICS OF CANADA LTD.
EXAMPLE 2: Perform two calculations using $840 and $525, both of which already
include tax. Calculate the tax on the total and the total without tax.
EXEMPLE 2: Réalise deux calculs en utilisant $840 et $525, les deux incluant déjà
la taxe. Calcule la taxe sur le total et le total sans la taxe.
EJEMPLO 2: Realice dos cálculos utilizando $840 y $525, los cuales ya incluyen
impuesto. Calcule et impuesto sobre el total y el total sin impuesto.
2
1
3
F
840 840. 840.+
525
1’365. 525.+
.
1,365
1’300.
. . .
1,300
65.–
.
GARANTIE LIMITÉE
Au Canada:
Produits de bureau personnels
Bravo! Vous Venez de faire un excellent achat!
Sharp Électronique du Canada Ltée (ci-après nommée “Sharp”) donne la garantie expresse
suivante à l’acheteur initial du produit ci-dessous mentionné de Sharp, si celui-ci est emballé
dans son contenant original et s’il est vendu et distribué au Canada par Sharp ou par un
Détaillant autorisé Sharp .
Sharp garantit que ledit produit est, s’il est utilisé et entretenu normalement, exempt de défaut
de fabrication. Si un défaut de fabrication est décelé durant la période de garantie stipulée,
Sharp s’engage à réparer ou remplacer, selon son choix, le produit spécifié ci-dessous.
La garantie offerte par Sharp ne s’applique pas:
(a) Aux appareils qui ont été l’objet d’un emploi abusif, de négligence, d’un accident, d’une
installation inadéquate ou d’une utilisation non appropriée, tel qu’il est mentionné dans le
manuel du propriétaire;
(b) Aux produits Sharp altérés, modifiés, réglés ou réparés ailleurs qu’aux bureaux de Sharp,
à un Centre agréé de service Sharp ou à un Détaillant autorisé au service Sharp;
(c) Au dommage causé ou réparation requise à la suite de l’utilisation avec des articles non
désignés ou approuvés par Sharp, y compris, mais non limité au papier, les piles ou
logiciel;
(d) Au remplacement des accessoires, des pièces en verre, des articles consommables ou
périphériques, devenu nécessaire à la suite d’une utilisation normale du produit, y compris,
mais sans en être limité, aux piles, le ruban, le ruban correcteur, les adapteurs c.a., le
rouleau encreur, la marguerite ou le papier;
(e) Aux défauts cosmétiques à la surface ou à l’extérieur de l’appareil, et qui sont causés par
une usure normale;
(f) Aux dommages causés par des conditions extérieures et relatives à l’environnement, y
compris mais non limité à du liquide répandu, une tension de la ligne électrique ou de
transmission trop élevée ou autre;
(g) Aux produits dont le numéro de série et de modèle ou le marquage CSA/CUL, ou les
deux, ont été enlevés ou éffacés;
(h) Aux produits de utilisés à des fins de location.
(i) Aux coûts d’installation, configuration et/ou programmation.
Si un défaut de fabrication est décelé dans ce produit Sharp au cours de la période de la
garantie, la réparation sous garantie est offerte à la condition que le produit Sharp soit livré
ainsi que la preuve d’achat et une copie de cette GARANTIE LIMITÉE à un Centre agréé de
service Sharp ou à un Détaillant autorisé au service Sharp.
La garantie ci-dessus constitue la seule garantie expresse accordée par Sharp. Aucun autre
détaillant, aucun centre de service, ses représentants ou ses employés, n’est autorisé à
prolonger la durée de la garantie, à fournir des garanties autres ou à transférer cette garantie
au nom de Sharp. Dans la mesure où la loi en vigueur le permet, Sharp décline toute
responsabilité pour les pertes ou les dommages directs ou indirects, pour les pertes ou les
dommages imprévus et pour les pertes de profits indirectes résultant d’un défaut de fabrication
du produit, y compris les dommages reliés à la perte de temps ou d’utilisation de ce produit
Sharp. L’acheteur doit assumer les coûts de démontage, de réinstallation, de transport et
d’assurance de l’appareil. La réparation des défectuosités, selon la manière et durant la période
de temps ci-haut décrites, constitue l’exécution complète de toutes les obligations et les
responsabilités de Sharp vis-à-vis l’acheteur en ce qui a trait au produit et constituera un
acquittement complet pour toute réclamation, qu’elle soit basée sur le contrat, la négligence,
la responsabilité stricte ou autre.
Personal Computer 1 year
Electronic Organizer 1 year
Personal Digital Assistant 1 year
Calculatrice sans imprimante 1 an
Calculatrice avec imprimante 6 mois
Calculatrice de poche 1 an
Pour obtenir le nom et l’adresse du Centre de service ou du Détaillant autorisé au service
SHARP ÉLECTRONIQUE DU CANADA LTÉE
335 Britannia Road East
Mississauga, Ontario
L4Z 1W9
(905) 568-7140 ou 1 (877) SHARP-CC
Site web: www.sharp.ca
PÉRIODES DE GARANTIE
Agenda électronique 1 an
Ordinateur Portatif 1 an
Assistant Numérique Personnel 1 an
Sharp le plus près, veuillez écrire ou téléphoner à:
SHARP ÉLECTRONIQUE DU CANADA LTÉE.
EL-1192BL(U1C)-2
0
A
➀