SEA HALF TANK,MINI TANK Installation Manual
HALF TANK
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
ATTUATORE OLEODINAMICO PER CANCELLI A BATTENTE
HYDRAULIC OPERATOR FOR SWING GATE
ACTUATEUR HYDRAULIQUE POUR PORTAIL À BATTANTS
ACTUADOR OLEODINAMICO PARA CANCELAS ABATIBLES
ItalianoItaliano
EnglishEnglish
FrançaisFran ais
EspanolEspanol
REV 06 - 03/2015
67411170
MANUALE D`INSTALLAZIONE
ed informazioni sulla sicurezza
INSTALLATION MANUAL
and Security Information
MINI TANK
FEATURES AND SPECIFICATIONS
respectively 6m, 7 m and
Hydraulic locking is guaranteed on gates with length up to 1.80 m with the Half Tank 270 and Mini Tank operators
while for lengths up to 2.20 m use the Half Tank 390. An electric lock should be used for leaves (in all versions)
exceeding those lengths.
The HALF TANK 270, HALF TANK 390 and MINI TANK are high quality hydraulic operators for residential and
condominium use with leaf length up to 3 m.
Available in the following versions:
AC (with lock in opening and closing position)
SC (with lock only in closing )
SA (with lock only in opening )
SB (without lock)
The Half Tank 270-390 and Mini Tank are supplied with by-pass valves for the power regulation in both opening and
closing. Electronic adjustable slow down in opening and closing with control board. For the European laws and
directives actually in force it is strongly recommended to use the Safety Gate (device for the reading of the gate
position), for reverse in case of obstacle.
position
position
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
67411170
17
77
88
99
66
55
1010
11
33
44
22
Fig. 3
Dimensions (mm)
Half Tank 270
(*) Half Tank 390
Fig. 1
96
70
0
/ 4 *
1 00
1
2 0
7
2
0 /
3
9
0*
05
12
0
*
1 0
/ 9
x
y
Note: Version with brake in closing
+ 25 mm in x and y.
Version with brake in opening and
closing + 50 mm in x and y.
Fig. 2
Note: Version with brake in closing
+ 25 mm in x and y.
Version with brake in opening and
closing + 50 mm in x and y.
Dimensions (mm)
Mini Tank
70
9
0
20 7
9
9
5
106
0
x
y
1 Rod cover extrusion
2 External lock attachment
3 Front fixing
4 Rear bracket fixing plate
5 Hydraulic cylinder
6 By-pass valves
7 Electric motor
8 Hydraulic pump
9 Electric cable exit
10 Release key
HALF TANK - MINI TANK
EnglishEnglish
REV 06 - 03/2015
MINI TANK (230V) MINI TANK (120V) MINI TANK
230V (±5%) 50/60 Hz 120V (±5%) 50/60 Hz 230V (±5%) 50/60 Hz
180 W 240 W 180 W
1 A 2.45 A 1 A
270 mm
1,5 cm/s 1,7 cm/s 1 cm/s
40
30 bar
-40°C +60°C
130°C
250 daN
6,3 µF 60 µF 6,3 µF
10 kg
Ip55
3 m
90° - 110°
WHIT JOINT
Note: The frequency of use is valid only for the first hour at 20°C room temperature.
Note: in non-automatic logic, use operators without lock.
HALF TANK 270 (230V)
Note: The frequency of use is valid only for the first hour at 20°C room temperature.
Note: in non-automatic logic, use operators without lock.
HALF TANK 390 (230V) HALF TANK 270 (120V) HALF TANK 390 (120V)
55
230 V (±5%) 50/60 Hz
220 W
1 A
270 mm
40bar
130°C
640 daN
12,5µF
11,4 kg
Ip55
6 m
90° - 125°
-40°C +60°C
2 A
120 V (±5%) 50/60 Hz
390 mm 270 mm 390 mm
30bar 40bar 30bar
60µF
13,6 kg 11,4 kg 13,6 kg
7 m 6 m 7 m
USING GRAPHIC OPERATORS
HALF TANK 270-390
MINI TANK
CICLES/HOUR
MAX. LEAF LENGTH
OPERATORS
3 m
40
MINI TANK
MINI
TANK
6 m
7 m
HALF TANK 270
HALF TANK 270
55
HALF TANK 390
HALF TANK 390
67411170
HALF TANK - MINI TANK
EnglishEnglish
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
Cycles hour (at a temp. of 20°C)
TECHNICAL FEATURES
Power supply
Power
Absorbed current
Stroke
Rod speed
Cycles hour (at a temp. of 20°C)
Max working pressure
Operating temperatures
Thermal protection
Max Thrust
Capacitor
Weight
Protection class
Max leaf lenght
Opening degree of the leaf
18
TECHNICAL FEATURES
Power supply
Power
Absorbed current
Stroke
Rod speed
Max working pressure
Operating temperatures
Thermal protection
Max Thrust
Capacitor
Weight
Protection class
Max leaf lenght
Opening degree of the leaf
1 cm/s 1,5 cm/s 1,2 cm/s 1,7 cm/s
REV 06 - 03/2015
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
Fig. 4
Oil fill in
cover
Gate Clevis
Outer tube
End cover
j
ustme
e
y
Ad nt
k
By-
a
ss
v
l
ves
p
a
(
n
l
y f
o
r
he in
st
l
le )o t
a r
Aluminium release with key
(Optional)
S
mal nt v
ib
t
o
n
l
a i
r
a
i
pl s
t c
ra
m
ea
i f
Brass pin
(short)
Clevis Attach’T
Long front
fixation hinge
Post Clevis
Breather screw
Rod
67411170
Ro n
d
mo
un
t
i
n
g
f
or
d e
a
l
f
T
a
n
-M
i
n
i tan
H k k
HALF TANK - MINI TANK
EnglishEnglish
HALF TANK
MINI TANK
19
REV 06 - 03/2015
STANDARD INSTALLATION
1) Operator
2) Mechanical stop
3) Electronic control unit
4) Flashing lamp
5) Photocell Dx
6) Differential switch 16A - 0,03A
7) Photocell Sx
8) Start - stop push button with key
9) Antenna
10) Support for photocells with photocells
11) Warning notice
12) Safety Gate
INSTALLATION TYPE
It is possible to install the operators with the opening towards the inside (Fig. 6) or towards the outside (Fig. 7).
Install the operator always
on the inside of the
property
outside
inside
outside
inside
Inside Opening Installation Outside Opening Installation
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
Fig. 6
Fig. 7
67411170
HALF TANK - MINI TANK
EnglishEnglish
ENTRY
EXIT
11
44
1010
1010
11
77
1212
1212
55
99
88
22
66
33
22
11
2x
1
3
x
1
,5
3
x
1
3x1
x3
1
x
3 1,5
1
2
x
3x
1
1
52x ,
3
x
1,
5
1xRG
58
Fig. 5
20
REV 06 - 03/2015
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
67411170
HALF TANK - MINI TANK
EnglishEnglish
INSIDE OPENING INSTALLATION
Total stroke 270 mm - max suggested stroke 250 mm
a b d
max
(mm)
(mm)
(mm)
250
215
250
250
215
250 225
250 235
255 242
250 242
250
250
100
100
105
105
120
120
125
140
140
145
145
150
155
160
170
180
115
150
110
145
105
130
125
95
110
95
105
100
85
90
75
65
50
50
55
55
70
70
75
90
90
95
95
100
105
110
120
130
110°
90°
110°
90°
106°
90°
90°
100°
90°
100°
90°
90°
96°
90°
92°
92°
250
250
250
250
250
253
245
To obtain 110° with d > 55 mm it is necessary to make a niche in the gate.
To obtain 125° with d > 55 mm it is necessary to make a niche in the gate.
a b d
max
(mm)
(mm)
(mm)
368
295
372
300
372
370
370
310
370 330
370
371
355
355
370
370
360
365
369
370
370
125
130
140
145
145
160
175
185
185
195
195
240
240
250
250
260
260
270
280
295
170
170
235
165
230
210
195
145
190
140
175
110
125
105
115
95
100
90
80
65
75
80
90
95
95
110
120
130
130
140
140
185
185
195
195
205
205
215
230
245
125°
125°
90°
120°
90°
90°
90°
110°
90°
110°
90°
100°
90°
95°
90°
95°
90°
90°
90°
90°
370
370
370
370
370
370
369
Fig. 8
a
d
b
c
a b d
max
(mm)
(mm)
(mm)
250
215
250
250
215
249 225
250 235
255 240
249 240
248
247
100
100
105
105
120
120
125
140
140
145
145
150
155
160
170
180
115
150
110
145
105
130
125
95
110
95
105
100
85
90
75
65
50
50
55
55
70
70
75
90
90
95
95
100
105
110
120
130
110°
90°
110°
90°
105°
90°
90°
100°
90°
100°
90°
90°
95°
90°
90°
90°
250
250
250
250
250
250
246
HALF TANK 270
HALF TANK 390 MINI TANK
Max
Opening
Angle
Max stroke
(mm)
Stroke
for 90°(mm)
Total stroke 390 mm - max. recommended stroke 370 mm
Total stroke 270 mm - max suggested stroke 250 mm
Max
Opening
Angle
Max stroke
(mm)
Stroke
for 90°(mm)
Max
Opening
Angle
Max stroke
(mm)
Stroke
for 90°(mm)
Inside
Outside
21
REV 06 - 03/2015
a b
(mm)
(mm)
250
240
250
250
243
241
150
160
165
175
180
180
90
90
80
80
70
65
95°
90°
95°
90°
90°
90°
250
249
Fig. 9
a
d
b
c
HALF TANK 270 - MINI TANK
a b
(mm)
(mm)
356
342
345 336
330
335
319
250
255
265
270
275
275
100
95
95
90
90
90
100°
95°
95°
90°
90°
90°
325
342
HALF TANK 390
a
d
b
55
155 Min.
180
60 Min.
* 1250
**1500
55
155 Min.
d
If you have to make a niche observe
the dimensions shown in fig.10.
* Half Tank 270 - Mini Tank Version
** Half Tank 390 Version
DIMENSIONS EN mm
Fig. 10
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
HALF TANK - MINI TANK
EnglishEnglish
OUTSIDE OPENING INSTALLATION
Total stroke 270 mm - max suggested stroke 250 mm
Total stroke 390 mm - max. recommended stroke 370 mm
Max
Opening
Angle
Max stroke
(mm)
Stroke
for 90°(mm)
Max
Opening
Angle
Max stroke
(mm)
Stroke
for 90°(mm)
INSTALLATION ON MASONRY PILLARS, MAKING A NICHE
Inside
Outside
22
67411170
REV 06 - 03/2015
Fig. 11
(1)
PRELIMINARY
-Open the package carefully, paying attention to not lose
the parts reported in fig.4
-Fix the oscillating fork as in fig.11.
Attention: do not use the hammer to insert the short brass
pivot; the insertion of the pivot into the fork and bracket must be
made simply by hand pressure.
Attention
Do not incline the hydraulic operator further
then the allowed angle from the oscillating
fork (1), could cause the braking of it (1).
OSCILLATING FORK INSTALLATION
BACK FIXATION MOUNTING
According to the chosen opening type (inside or
outside) and according to the chosen max.
rotation of the leaf (see page 21-22) the bracket
must be first cut respecting the mesurment “a” on
pag. 21-22 and than welded as in fig.14.
The support must be positioned so that the
operator is in perfect horizontal position (Fig. 14,
Fig.15).
Adjustable back fixation (with screw)
(Accessories on request)
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
67411170
Fig. 12
Fig. 13
55 mm
65 m m
Fig. 14
9
8 m
m
8
mm
5
HALF TANK - MINI TANK
EnglishEnglish
23
REV 06 - 03/2015
Loading...