Schneider Electric Erie PopTop Series Installation Instructions

Erie™ PopTop™ Series

Valve Bodies and Actuators

Installation Instructions

Product Description

Erie™ PopTop™ Series valve bodies and actuators provide easy installation for a variety of heating and cooling applications. The valve’s actuator can be installed after the valve body has been installed onto the fan coil, baseboard or air handler. VS Series valves are available for low pressure steam applications. PopTop Series are two position spring return valves. When powered, the actuator moves to the desired position, tensing the spring return system. When power is removed the actuator retur ns to the normal position. PopTop Series two position spring return valves can be purchased with an optional built-in auxiliary SPDT end switch for interfacing or signaling; for example, zone pump burner control. Actuators are designed fror cycling applications (not constantly powered).

Speciﬁcations

Service Hot and chilled water models, up to

50% glycol. Steam models up to 15 psi

(both valve body and valve actuator must be rated for high temperature)

System Static Pressure Limits

Fluid/Ambient Temperature Limits

Close-off See Table 2

Seat Leakage ANSI class IV (0.01%) with pressure at

inlet (B-port/A-por t, if 3-way)

Body Forged brass

Stem Nickel-plated

Seat Brass

Paddle (VT series) (VS series)

Actuator Voltage

Power Requirements

24 Vac @ 50/60 Hz, 110 Vac @ 50 Hz,

120 Vac @ 60 Hz, 230 Vac @ 50 Hz,

240 Vac @ 60 Hz, 208 Vac @ 50/60 Hz,

400 psi (2758 kPa)

See Table 1

Buna N

Highly saturated nitrile

277 Vac @ 50/60 Hz

6.5 watts, 7.5 Va

VT/VS Series with General Close-Off Actuator

VT/VS Series with High Close-Off Actuator

Features

• Direct replacement for all existing two-position PopTop applications

• Hysteresis synchronous motor for long life

• Spring return operation provides a fail-safe

• Valve body rated for 400 psi static pressure

• Available in a variety of voltages

• Actuator mounts directly onto valve body without need for linkages or calibration

• Manual override lever (normally closed only)

• Actuator can be replaced without any tools, or removal of valve from system

• VS Series available for low pressure steam

Agency Listings UL873

CUL

European Community Australia

Shipping Weight (Actuator/Valve Assembly)

Table 1: Valve Body and Actuator Models

Model Temperature Range

VTxxxx

VSxxxx

Axx3xxx

Axx4xxx

For steam applications both valve body and valve actuator must be rated for high temperature. Example: VS2213G14A020 = Assembly. VS2213 = Valve body. AG14A020 = Actuator.

Underwriters laboratories (File #E9429

Catagory Temperature Indicating and

Regulating Equipment).

UL Listed for use in Canada by

Underwriters Laboratory. Canadian

Standards C22.2 No. 24. EMC Directive

(89/336/EEC). Low Voltage Directive

(72/23/EEC).

This product meets requirements

to bear the RSM Mark according

to the terms speciﬁed by the Communications Authority under the Radio Communications Act of 1992.

2.25 lbs (1020 g).

32×…200°F (ﬂuid) @ 104 °F (Ambient) (0…93°C @ 40°C)

32×…250°F (ﬂuid) @ 169 °F (Ambient) (0…121°C @ 76°C), and/or 15 PSI (103 kPa)

Steam

32×…200°F (ﬂuid) @ 104 °F (Ambient) (0…93°C @ 40°C)

32×…250°F (ﬂuid) @ 169 °F (Ambient) \(0… 121°C @ 76°C), and/or 15 PSI (103 kPa)

Steam

Installation Instructions

(61 mm)

Accessories for Inverted Flare Connection Valves

3/4” inverted ﬂare bodies accept the following adapters to copper pipe:

436-214-1 Union nut & elbow assembly, female for 1/2” (5/8” O.D.) copper, 15/16” long

436-220 Union nut & coupling assembly, female for 1/2” (5/8” O.D.) copper, 1-1/16” long

436-252 Union nut & coupling assembly, female for 3/4” (7/8” O.D.) copper, 1-27/32” long

436-229-3 Union nut & nipple assembly, male for 1/2” (5/8” O.D.) copper, 3” long

436-214-4 Union nut & elbow assembly, male for 1/2” (5/8” O.D.) copper, 1-15/16” long

436-256 Union nut & coupling assembly, female for 1” (1-1/8” O.D.) copper, 1-3/8” long

Table 2: Flow Coefﬁcients and Maximum Close-Off Pressure Differentials

Valve Size Connection Type 2-way Cv (kv) 3-way Cv (kv) (G) Close-Off ∆P PSI

(kPa)

1/2" NPT, SW, Rp, SAE

3/4" IFL

1/2" NPT, SW, Rp, SAE

3/4" NPT, SW, IFL, Rp

1.0 (0.9) 1.5 (30) 60 (414) 75 (517)

2.5 (2.2) 3.0 (2.6) 40 (276) 50 (344)

1/2" NPT, SW, SAE, Rp

3.5 (3.0) 4.0 (3.4) 25 (172) 30 (208)3/4" NPT, SW, IFL, Rp

1" SW

3/4" NPT, SW, Rp

1" SW

5.0 (4.3) 5.0 (4.3) 20 (137) 25 (172)

3/4" NPT, SW, Rp 7.5 (6.5) 7.5 (6.5) 17 (117) 20 (137)

1" NPT, SW, Rp

1-1/4" SW

NPT - Threaded (female) SW - Sweat

8.0 (6.9) 8.0 (6.9) 17 (117) 20 (137)

IFL - Inverted Flare SAE - Society of Automotive Engineers Flare (male) Rp - “Metric” Threaded (female) G - General close off acutuator H - High close off actuator

(H) PSI Close-Off ∆P (kPa)

Table 3: Water Valve Sizing*

∆P 1.0 Cv 1.5 Cv 2.5 Cv 3.0 Cv 3.5 Cv 4.0 Cv 5.0 Cv 7.5 Cv 8.0 Cv

1 PSI

2 PSI

3 PSI

4 PSI

5 PSI

1.0 1.5 2.5 3.0 3.5 4.0 5.0 7.5 8.0

1.4 2.1 3.5 4.2 4.9 5.7 7.1 10.6 11.3

1.7 2.6 4.3 5.2 6.1 6.9 8.7 13.0 13.9

2.0 3.0 5.0 6.0 7.0 8.0 10.0 15.0 16.0

2.2 3.4 5.6 6.7 7.8 8.9 11.2 16.8 17.9

* Water capacity in gallons per minute (GPM)

Dimensions

General Close-Off High Close-Off

3-11/16” (94 mm)

3-1/4”

(83 mm)

1-1/8”

(29 mm)

2-3/8”

(61 mm)

3-3/16” (81 mm)

B-PORT

A A

A-PORT

B 2-WAY

C 3-WAY

7/16”

(12 mm)

2.-3/8”

(61 mm)

2-7/16”

B-PORT

A A

3-11/16” (94 mm)

3-1/4”

(83 mm)

(32 mm)

1-1/4”

A-PORT

2-7/16”

(62 mm)

B 2-WAY

3-3/16”

(82 mm)

C 3-WAY

2 5/8”

(67 mm)

(14 mm)

9/16”

2-7/16”

(62 mm)

+ 5 hidden pages