Schneider Electric AP9640, AP9641, AP9643, AP9544, AP9547 Installation Manual

Installation Manual

UPS Network Management Card 3

AP9640, AP9641, AP9643,

AP9544, AP9547

990-9996H-001

Publication Date: February 2021

Schneider Electric IT Corporation Legal Disclaimer

The information presented in this manual is not warranted by the Schneider Electric IT Corporation to be authoritative, error free, or complete. This publication is not meant to be a substitute for a detailed operational and site specific development plan. Therefore, Schneider Electric IT Corporation assumes no liability for damages, violations of codes, improper installation, system failures, or any other problems that could arise based on the use of this Publication.

The information contained in this Publication is provided as is and has been prepared solely for the purpose of evaluating data center design and construction. This Publication has been compiled in good faith by Schneider Electric IT Corporation. However, no representation is made or warranty given, either express or implied, as to the completeness or accuracy of the information this Publication contains.

IN NO EVENT SHALL SCHNEIDER ELECTRIC IT CORPORATION, OR ANY PARENT, AFFILIATE OR SUBSIDIARY COMPANY OF SCHNEIDER ELECTRIC IT CORPORATION OR THEIR RESPECTIVE OFFICERS, DIRECTORS, OR EMPLOYEES BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL, OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, CONTRACT, REVENUE, DATA, INFORMATION, OR BUSINESS INTERRUPTION) RESULTING FROM, ARISING OUT, OR IN CONNECTION WITH THE USE OF, OR INABILITY TO USE THIS PUBLICATION OR THE CONTENT, EVEN IF SCHNEIDER ELECTRIC IT CORPORATION HAS BEEN EXPRESSLY ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SCHNEIDER ELECTRIC IT CORPORATION RESERVES THE RIGHT TO MAKE CHANGES OR UPDATES WITH RESPECT TO OR IN THE CONTENT OF THE PUBLICATION OR THE FORMAT THEREOF AT ANY TIME WITHOUT NOTICE.

Copyright, intellectual, and all other proprietary rights in the content (including but not limited to software, audio, video, text, and photographs) rests with Schneider Electric IT Corporation or its licensors. All rights in the content not expressly granted herein are reserved. No rights of any kind are licensed or assigned or shall otherwise pass to persons accessing this information.

This Publication shall not be for resale in whole or in part.

This manual is available in English on the APC website (www.apc.com).

Dieses Handbuch ist in Deutsch auf der APC webseite (www.apc.com) verfügbar.

Данное руководство на русском языке доступно на сайте APC (www.apc.com )

本マニュアルの日本語版は APC ウェブサイト (www.apc.com) からダウンロードできます。

在 APC 公司的网站上 (www.apc.com) 有本手册的中文版。

Contents

Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Preliminary Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Installation in a UPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Expansion/Triple Chassis Installation . . . . . . . . . . . . . . . . . . . . . 9

Safety Information for the Network Management Card 3 . . . 2

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Supported Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Related documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Changing Web UI Language . . . . . . . . . . . . . . . . . . . . . . . . 6

How to install the card for different UPS models . . . . . . . . . 7

Step 1: Install the Network Management Card . . . . . . . . . . 7

Step 2: Configure the Network Management Card . . . . . . . 8

When to use an Expansion Chassis . . . . . . . . . . . . . . . . . . 9

Step 1: Disconnect the chassis from all power . . . . . . . . . . 9

Step 2: Install the Network Management Card . . . . . . . . . . 9

Quick Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Step 1: Configure TCP/IP Settings . . . . . . . . . . . . . . . . . . 11

TCP/IP configuration methods . . . . . . . . . . . . . . . . . . . . . . 12

UPS User Interface Display . . . . . . . . . . . . . . . . . . . . . . . . 12

Local access to the command line interface . . . . . . . . . . . 13

Remote access to the command line interface . . . . . . . . . 14

Command line interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Device IP Configuration Wizard . . . . . . . . . . . . . . . . . . . . . 15

DHCP and BOOTP configuration . . . . . . . . . . . . . . . . . . . . 16

.INI file utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Step 2: Enable Network Protocols . . . . . . . . . . . . . . . . . . . 18

Step 3: Access the Configured NMC . . . . . . . . . . . . . . . . . 18

Installation Manual

How to Access a Configured Network Management Card . . . . 19

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Web interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Command Line Interface access - SSH and Telnet Access 20

Simple Network Management Protocol (SNMP) . . . . . . . . 20

SCP and FTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Manage the security of your system . . . . . . . . . . . . . . . . . 21

How to Reset after a Lost Password . . . . . . . . . . . . . . . . . . . . . 22

How to Install Multiple Management Cards . . . . . . . . . . . . . . . . 23

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Two models of expansion chassis . . . . . . . . . . . . . . . . . . . 24

Installing cards in an expansion chassis . . . . . . . . . . . . . . 24

Installing cards in an expansion chassis set up serially . . . 24

Installing cards in a Symmetra UPS . . . . . . . . . . . . . . . . . 25

Specifications AP9640, AP9641 . . . . . . . . . . . . . . . . . . . . . . . . . 27

Specifications AP9643 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Specifications AP9544 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Specifications AP9547 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Installation Manual

Important Safety Information

Read the instructions carefully to become familiar with the equipment before trying to install, operate, service, or maintain it. The following special messages may appear throughout this manual or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.

The addition of this symbol to a Danger or Warning safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

DANGER

DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

WARNING indicates a potentially hazardous situation which, if not avoided, can result in death or serious injury.

CAUTION

CAUTION indicates a potentially hazardous situation which, if not avoided, can result in minor or moderate injury.

NOTICE

NOTICE addresses practices not related to physical injury including certain environmental hazards, potential damage or loss of data.

Installation Manual

Safety Information for the Network Management Card 3

The Network Management Card (NMC) contains a removable battery. If this battery is ingested, seek immediate medical attention.

WARNING

HAZARD OF INTERNAL BURNS

• Do not ingest the battery.

• Keep batteries out of reach of children.

Failure to follow these instructions can result in serious injury or death.

Note: Secure the NMC to the UPS device’s SmartSlot using screws to keep the battery out of reach.

Installation Manual

Preliminary Information

Features

The Schneider Electric UPS Network Management Cards (AP9640, AP9641, AP9643, AP9544, and AP9547) discussed in this document are Web-based, IPv6 Ready products. Devices with the NMC installed can be managed using multiple open standards such as:

Hypertext Transfer Protocol over Secure Sockets Layer (HTTPS)

Secure Copy (SCP) RADIUS

Extensible Authentication Protocol (EAP) over LAN (EAPoL)

Simple Network Management Protocol versions 1, 2c and 3

Telnet Modbus

Hypertext Transfer Protocol (HTTP) File Transfer Protocol (FTP)

The AP9640 Network Management Card:

• Provides UPS control and self-test scheduling features.

• Provides data and event logs.

• Enables you to set up notifications through event logging, e-mail, Syslog and SNMP traps.

• Provides support for PowerChute

• Supports using a Dynamic Host Configuration Protocol (DHCP) or BOOTstrap Protocol (BOOTP) server to provide the network (TCP/IP) values of the NMC.

• Provides the ability to export a user configuration (.ini) file from a configured card to one or more unconfigured cards without converting the file to a binary file.

• Provides a selection of security protocols for authentication and encryption.

• Communicates with StruxureWare Data Center Expert, StruxureWare Operations, or EcoStruxure™ IT.

• Supports Modbus TCP/IP.

Secure SHell (SSH)

BACnet

Syslog

Network Shutdown.

Installation Manual

The AP9641 Network Management Card includes all AP9640 Network Management Card features and the following:

• Provides two USB ports, which support upgrading the UPS firmware from a USB flash drive, and wi-fi support with the optional APC USB Wi-Fi Device

(AP9834). For information on how to configure wi-fi, refer to the APC USB Wi-Fi Device Quick Start Guide (https://www.apc.com/us/en/download/

document/SPD_CCON-NMC3WIFI_EN).

• Supports two universal input/output ports, to which you can connect:

– Temperature (AP9335T) or temperature/humidity sensors

(AP9335TH)

– Relay input/output connectors that support two input contacts and one

output relay (using the AP9810 Dry Contact I/O Accessory, which is an optional add-on)

• Supports Modbus RTU 2-wire RS-485 via Universal I/O port 2, in addition to Modbus TCP/IP. For information on how to configure Modbus RTU, refer to the Modbus Documentation Addendum.

The AP9643 Network Management Card includes all AP9640 Network Management Card features and the following:

• Provides two USB ports, which support upgrading the UPS firmware from a USB flash drive, and wi-fi support with the optional APC USB Wi-Fi Device

(AP9834). For information on how to configure wi-fi, refer to the APC USB Wi-Fi Device Quick Start Guide (https://www.apc.com/us/en/download/

document/SPD_CCON-NMC3WIFI_EN).

• Supports one universal input/output port, to which you can connect:

– Temperature (AP9335T) or temperature/humidity sensor (AP9335TH)

– Relay input/output connector that support two input contacts and one

output relay (using the AP9810 Dry Contact I/O Accessory, which is an optional add-on)

• Supports Modbus RTU via the 4-wire opto-isolated serial RS-485 port, in addition to Modbus TCP/IP. For information on how to configure Modbus RTU, refer to the Modbus Documentation Addendum.

The AP9544 and AP9547 Network Management Cards:

• Provide one USB-A host port.

• Provide data and event logs.

• Enable you to set up notifications through event logging, e-mail, Syslog and SNMP traps.

• Provide support for PowerChute® Network Shutdown. NOTE: The AP9547 card in Easy UPS devices with the E3S, E3M, and E3L prefixes only support the shut down of the connected servers and applications running on the servers. It is not supported to shut down the UPS device(s).

• Support using a Dynamic Host Configuration Protocol (DHCP) or BOOTstrap Protocol (BOOTP) server to provide the network (TCP/IP) values of the NMC.

Installation Manual

• Provide the ability to export a user configuration (.ini) file from a configured card to one or more unconfigured cards without converting the file to a binary file.

• Provide a selection of security protocols for authentication and encryption.

• Communicate with StruxureWare Data Center Expert, StruxureWare Operations, or EcoStruxure™ IT.

• Support Modbus TCP/IP.

Supported Devices

The Network Management Card 3 is compatible with:

• Smart-UPS

devices with a SmartSlot with the SUM, SURT, SURTA, SURTD, SMT, SMX, and SRT prefixes, and SUA devices manufactured after 2008 *.

• Single phase Symmetra UPS devices.

• Single phase Easy UPS devices with the SMV, SMVS, SRV, and SRVS prefixes (AP9544 only).

• Three phase Easy UPS devices with the E3S, E3M, and E3L prefixes (AP9547 only).

* To view the full list of compatible UPS in which an NMC 3 can be installed, see Knowledge Base article FA237786 on the APC website (www.apc.com/support).

Inventory

The Network Management Card package includes the following items:

• This Installation Manual

• UPS Network Management Card 3

• Micro-USB configuration cable (part number 960-0603)

• Temperature sensor (AP9335T)—AP9641 and AP9643 Network Management Cards only

• Ferrite bead—AP9544 and AP9547 Network Management Cards only

• Network Management Card quality assurance test slip

• Warranty registration form

The quality assurance test slip contains the MAC address that you may need when performing the procedures in “UPS User Interface Display” on page 12. You can also find the MAC address on the bottom of your NMC.

Disclaimer

Schneider Electric is not responsible for damage sustained during reshipment of this product.

The Network Management Card 3 (NMC 3) is sensitive to static electricity. When handling the NMC, touch only the end plate while using one or more of these electrostatic-discharge devices (ESDs): wrist straps, heel straps, toe straps, or conductive shoes.

Please recycle

The shipping materials are recyclable. Save them for later use, or dispose of them appropriately.

Management products, including the NMC, contain removable, lithium coin-cell batteries. When discarding these batteries, you must follow local rules for recycling.

Changing Web UI Language

You can change the language the NMC Web interface is displayed in via the log in screen. See “Changing Web UI Language” in the User Guide (www.apc.com/us/en/download/document/SPD_CCON-AYCEFJ_EN) for more information.

Installation Manual

Installation in a UPS

How to install the card for different UPS models

To view the full list of compatible UPS in which an NMC can be installed, see Knowledge Base article FA237786 on the APC website (www.apc.com/support).

In a Symmetra UPS that uses more than one management product, you must install the management products in the correct order for them to operate properly.

See “How to Install Multiple Management Cards” on page 23.

Step 1: Install the Network Management Card

You do not need to turn off power to install the NMC in a supported Smart-UPS, Symmetra UPS, or Easy UPS. If you want to turn off your UPS before installing the Network Management Card, see the Knowledge Base article FA156132 on the APC website (www.apc.com/

support).

The NMC is sensitive to static electricity. When handling the NMC, touch only the end plate while using one or more of these electrostaticdischarge devices (ESDs): wrist straps, heel straps, toe straps, or conductive shoes.

The Network Management Card (NMC) contains a removable battery. If this battery is ingested, seek immediate medical attention.

WARNING

HAZARD OF INTERNAL BURNS

• Do not ingest the battery.

• Keep batteries out of reach of children.

Failure to follow these instructions can result in serious injury or death.

Note: Secure the NMC to the UPS device’s SmartSlot using screws to keep the battery out of reach.

Installation Manual

+ 28 hidden pages