Sargent Assa Abloy IN120 Installation Instructions Manual

IN120

WiFi

Cylindrical Lock
Installation Instructions

A8152C
01/14

Copyright 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Sargent Manufacturing Company is prohibited.

Table of Contents

1

Warning ...................................................................................3

2

General Description .................................................................4

3

Specifications ..........................................................................4

4

System Overview .....................................................................4

5

Parts Breakdown .....................................................................5

6

Lock Installation ......................................................................7

7

Operational Check ................................................................19

1

Warning

Changes or modifications to this device not expressly approved by ASSA ABLOY
could void the user’s authority to operate the equipment.

FCC:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada:

This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations.

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.

Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements
d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce
dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.
“This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.”

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and
its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.

Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et
d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.

Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening, and SARGENT
Manufacturing makes no representations or warranties concerning what such impact may be in any specific situation. When retrofitting
any portion of an existing fire rated opening, or specifying and installing a new fire-rated opening, please consult with a code specialist

!

or local code official (Authority Having Jurisdiction) to ensure compliance with all applicable codes and ratings.

To avoid possible damage from electrostatic discharge (ESD), some basic precautions should be used when handling
electronic components:

• Minimize build-up of static by touching and/or maintaining contact with unpainted metal surfaces such as

Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

12/20/13

1-800-810-WIRE • www.sargentlock.com • A8152C

door hinges, latches, and mounting plates especially when mounting electronic components such as readers
and controllers onto the door.

• Leave components (reader and controller) protected in their respective anti-static bags until ready
for installation

• Do not touch pins, leads or solder connections on the circuit boards

IN120 Cylindrical Lock

2

3

General Description

The IN120 WiFi lock offers the ease and flexibility of WiFi in a streamlined design, setting a new standard for
aesthetics and performance. The IN120 uses IEEE 802.11 WiFi communication and a flexible feature set for
easier, more cost-effective installations, allowing facilities to leverage their IT infrastructure to expand access
control coverage to more doors. Featuring HID® multiCLASS SE™ technology, it supports heightened identity
security and multiple credentials, including NFC-enabled mobile phones.

This product is operated by six (6) “AA” alkaline batteries, or can be hard-powered using an optional
9-24VDC power supply connected by a harness through the door.

SARGENT cylindrical locks are designed with quality components to provide high security, performance

and durability.

HID, iCLASS, iCLASS SE, and multiCLASS SE are registered trademarks or trademarks of HID Global in the U.S. and/or
other countries.

Hardware Specifications

• Complete lockset with on-board memory

• ADA compliant

• Easily retrofits existing (cylindrical lock)
door preps

• Latch - 1/2” standard 3/4” throw fire-rated
double doors (optional) (41- prefix)

• Deadlocking latch - Stainless steel, non handed

• Lock furnished for 1-3/4” doors.
For other thicknesses, consult factory.

• UL Listed (3 hr.)

• Outside lever controlled by contactless reader
or mechanical cylinder

4

Electronic Specifications

• Input Power: DC 9V, 1.5A (6 AA alkaline batteries)

• Optional hard-power 12VDC to 24VDC

• HID® multiCLASS SE™ technology offers support
for the following credentials:

• High Frequency (13.56 MHz):

• HID iCLASS

• HID iCLASS SE® (SIO-enabled)

• HID iCLASS

• HID MIFARE® SE

• HID DESfire® EV1 SE

• MIFARE Classic

• DESfire EV1

• FeliCa

• Low Frequency (125 kHz):

• HID Prox

!

To comply with “Fire Listed” doors, the batteries must be replaced with alkaline batteries only.

®

®

®

Seos

™

• WiFi (IEEE 802.11 b/g/n)

• Multiple time zone and holiday access scheduling

• First-in unlock or automatic unlock configuration,
based on specified time schedule

• Support for most advanced wireless encryption
and authentication standards such as WEP, WPA,
WPA2 and 802.1x*

• 2,400 users per lock; 10,000 event audit trail

• Privacy button

*For specific security information, please contact
your local ASSA ABLOY Door Security Solutions
sales consultant or call 800-810-WIRE.

Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

12/20/13

4 1-800-810-WIRE • www.sargentlock.com • A8152C

IN120 Cylindrical Lock

5

Parts Breakdown

1*

2

3

5

6

4

7

ITEM PART NUMBER/ORDER STRING DESCRIPTION COLOR/TRIM QTY

1 IN-120-EM01-IP-B HID iCLASS®, HID iCLASS SE® (SIO-enabled), HID iCLASS® Seos™, HID MIFARE®

SE, HID DESfire® EV1 SE, HID Prox®, NFC-enabled mobile phones

IN-120-EM01-IP-W HID iCLASS®, HID iCLASS SE® (SIO-enabled), HID iCLASS® Seos™, HID MIFARE®

SE, HID DESfire® EV1 SE, HID Prox®, NFC-enabled mobile phones

IN-120-EM01-IP-MB-[finish]* HID iCLASS®, HID iCLASS SE® (SIO-enabled), HID iCLASS® Seos™, HID MIFARE®

SE, HID DESfire® EV1 SE, HID Prox®, NFC-enabled mobile phones

IN-120-EM01-IP-MW-[finish]* HID iCLASS®, HID iCLASS SE® (SIO-enabled), HID iCLASS® Seos™, HID MIFARE

SE, HID DESfire® EV1 SE, HID Prox®, NFC-enabled mobile phones

IN-120-EM01-IPS-B All credentials supported by the IP option plus MIFARE Classic and DESfire EV1 Black

IN-120-EM01-IPS-W All credentials supported by the IP option plus MIFARE Classic and DESfire EV1 White

IN-120-EM01-IPS-MB-[finish]* All credentials supported by the IP option plus MIFARE Classic and DESfire EV1 Black with metal trim

IN-120-EM01-IPS-MW-[finish]* All credentials supported by the IP option plus MIFARE Classic and DESfire EV1 White with metal trim

IN-120-EM01-CP-B FeliCa, HID Prox®, NFC-enabled mobile phones Black

IN-120-EM01-CP-W FeliCa, HID Prox®, NFC-enabled mobile phones White

IN-120-EM01-CP-MB-[finish]* FeliCa, HID Prox®, NFC-enabled mobile phones Black with metal trim

IN-120-EM01-CP-MW-[finish]* FeliCa, HID Prox®, NFC-enabled mobile phones White with metal trim

2 IN120-EM04 Inside Mounting Kit (mounting plate & hardware) 1

3 IN120-EM03 WiFi Controller 1

4 N/A AA battery 6

5 IN-120-EM02-B Inside Escutcheon Black 1

IN-120-EM02-W Inside Escutcheon White

IN-120-EM02-MB-[finish]* Inside Escutcheon Black with metal trim

IN-120-EM02-MW-[finish]* Inside Escutcheon White with metal trim

6 A8149 Field prep template (not shown) 1

7 4712 Door manufacturers template (not shown) 1

-- A8152 Instructions (this manual) 1

Black 1

White

Black with metal trim

®

White with metal trim

Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

* Specify finish

1-800-810-WIRE • www.sargentlock.com • A8152C 5

12/20/13

Parts Breakdown (Continued)

5

4

3

2

1

IN120 Cylindrical Lock

12

11

*

8

7

6

9

10

5

4

PART NO./ORDER

ITEM

1 --- Outside Lever (Reference Catalog for Available Styles) 1

2 10-0043 Lever Retainer Key (In Screw Pack 10-2052) 1

3 --- Cylinder Assembly (Reference Catalog for Available Cylinders) 1

4 --- Rose (Reference Catalog for Avalable Styles) 2

5 10-0792 Spacer Bushing 2

6 10-3049 Outside Rose Spring Assembly 1

7 10-3407 Lockbody Assembly 10G77 (Standard Cylinder) 1

13

8 10-0847 Adapter Plate/Spacer (Only Included With 1-3/8” Thick Doors) 1

9 10-3192 Latch Assembly 1

10 10-2052 Screw Pack 2

11 10-3048 Inside Rose Spring Assembly 1

12 --- Inside Lever (Reference Catalog for Available Styles) 1

13 52-5373 DPS (Door Position Switch) Kit 1

*Adapter Plate/Spacer (10-0847)
is only shipped with orders
that specify 1-3/8” doors.

Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

STRING

10-3412 Lockbody - LFIC

10-3417 Lockbody - SFIC

DESCRIPTION

Tools Required:

• #2 Phillips screwdriver

• Flat head screwdriver

• Security allen wrench

QTY.

(provided)

12/20/13

6 1-800-810-WIRE • www.sargentlock.com • A8152C