Sanyo DP26647 User Manual

Model Nos. :

Printed in U.S.A. SMC, May 2007 Part No. :

1JC6P1P0261––

LCD HDTV Owner’s Manual

ENGLISH

Table of Contents . . . . . 3

Need assistance?

Visit our Web site at

www.sanyoctv.com

or call toll free

1-800-877-5032

We can Help!

DP26647 DP32647

DP26647

DP32647

Important Safety Instructions for LCD DTV

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit fully into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power -supply cord or plug is damaged, liquid

has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. If an outside antenna is connected to the television equipment, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges. In the U.S. Selection 810-21 of the National Electrical Code provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrodes.

16. An outside antenna system should not be located in the vicinity of overhead power lines or other electrical light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

17. Wall or Ceiling Mounting—The product should be mounted to a wall or ceiling only as recommended by the manufacturer

18. "Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus."

19. When the MAINS plug is used as the disconnect device, the disconnect device shall remain readily operable.

EXAMPLE OF ANTENNA GROUNDING ACCORDING TO NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

IMPORTANT SAFETY INSTRUCTIONS

“Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 82040 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.”

NEC

- NATIONAL ELECTRICAL CODE

ANTENNA LEAD IN WIRE

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUND CLAMP

ELECTRIC SERVICE EQUIPMENT

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

Welcome to the World of Sanyo

Thank you for purchasing this Sanyo LCD High-Definition Digital Television. You made an excellent choice for Performance, Reliability, Features, Value, and Styling. If assistance is needed, please call

1-800-877-5032 or visit our website at www.sanyoctv.com. We can help!

“As an ENERGY STAR®Partner, Sanyo Manufacturing Corporation has determined that this product meets the ENERGY STAR®guidelines for energy efficiency.”

TRADEMARKS INFORMATION:

Manufactured under license from Dolby Laboratories. “Dolby” is a trademark of Dolby Laboratories

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . 2

CONTENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

POSITIONING THE LCD DTV . . . . . . . . . . . . . . . . . . . . . 4

PROTECTING THE LCD SCREEN . . . . . . . . . . . . . . . . . . 4

REMOVING THE DTV STAND (OPTIONAL) . . . . . . . . . . 4

WALL MOUNTING (OPTIONAL) . . . . . . . . . . . . . . . . . . . 4

GETTING STARTED (REQUIRED INITIAL SETUP) . . . . . 5

Installing Batteries in the Remote Control . . . . . . . 5

Connect Signal (Digital / Analog) . . . . . . . . . . . . . 5

Plug in & Power the TV . . . . . . . . . . . . . . . . . . . . . 5

Perform All Channel Search . . . . . . . . . . . . . . . . . 5

HDTV BACK LEFT / RIGHT SIDE PANELS . . . . . . . . . . . 6

DIGITAL AV CONNECTIONS . . . . . . . . . . . . . . . . . . 7 ~ 8

HDMI CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . 7

HD DVD Player / Game System . . . . . . . . . . . . 7

Set-top Box (STB) with DVI Output . . . . . . . . . . 7

COMPONENT JACKS CONNECTIONS

HD DVD Player . . . . . . . . . . . . . . . . . . . . . . . . . 8

DIGITAL AUDIO OUT CONNECTION

Multichannel Receiver . . . . . . . . . . . . . . . . . . . . 8

ANALOG AV CONNECTIONS . . . . . . . . . . . . . . . . . . . . . 9

Stereo Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

VCR (or other analog device) . . . . . . . . . . . . . . . . 9

Connect Analog Cable Box or Cable,

VCR, and an Antenna . . . . . . . . . . . . . . . . . . . . . 10

REMOTE CONTROL OPERATION . . . . . . . . . . . . . . . . . 11

MENU OPERATION . . . . . . . . . . . . . . . . . . . . . . . 12 ~ 14

How to Operate the On-Screen Menu . . . . . . . . . 12

Menu Navigation Map . . . . . . . . . . . . . . . . . . . . . 12

Menu Options:

All Channel Search . . . . . . . . . . . . . . . . . . . . . . . 12

Analog Antenna Signal (Optional) . . . . . . . . . . . . 12

Picture/Sound Adjustment . . . . . . . . . . . . . . . . . . 12

Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Digital Cable Search (Optional) . . . . . . . . . . . . . . 13

Digital Add-On Search . . . . . . . . . . . . . . . . . . . . . 13

Channel Scan Memory . . . . . . . . . . . . . . . . . . . . 13

Digital Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Energy (Power) Saver . . . . . . . . . . . . . . . . . . . . . 14

V-Guide (Parental Control) . . . . . . . . . . . . . . . . . 15

HELPFUL HINTS (PROBLEMS / SOLUTIONS) . . . . . . . 16

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

FREQUENT ASKED QUESTION (FAQ)

The picture is not as clear as it should be. Am I using the best quality connection?

Picture quality is classified as follows:

RF Cable connection (analog) . . . . . . . . . . . . Basic

Video1 (Composite-Yellow) . . . . . . . . . . . . . . . Good

Video1 (S-Video) . . . . . . . . . . . . . . . . . . . . . . . Better

Video2 & 3 (Component: green, blue, red) . . Exceptional

HDMI1 / 2 or Antenna In (Digital) . . . . . . . . Ultimate

with a double “Z” is a registered

trademark of Sanyo Manufacturing Corporation.

This symbol on the nameplate means the product is Listed by Underwriters’ Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety standards against risk of fire, casualty and electrical hazards.

ENERGY STAR

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

PROTECTING THE LCD DTV SCREEN

The screen is likely to be damaged if it is not maintained properly. Do not use hard objects such as hard cloth or paper. Do not use excessive pressure when cleaning the screen; excessive pressure can cause permanent discoloration or dark spots.

NEVER spray liquids on the screen.

REMOVING THE DTV STAND

(Optional)

Tools Needed: Phillips screwdriver

Important Note:Place DTV face down on a padded or cushioned surface to protect the screen and finish.

Remove four (4) screws from the metal bracket. CAUTION: Hold the stand firmly as you remove the last screw.

Carefully remove the DTV stand.

WALL MOUNTING (Optional)

Use the threaded inserts on the back of your DTV to secure it using a wall mounting kit. VESA standard interface: DP26647: 100 x 10 0 DP32647: 200 x 200

Note: Wall Mounting kit is not

supplied.

Mounting screws measurements:

DP26647—M4 Diameter, Length—10mm (maximum). DP32647—M6 Diameter, Length—12mm (maximum).

POSITIONING THE LCD DTV

Always use an appropriate table or stand when positioning your DTV. Do not position the DTV in a

confined area. Allow adequate space for proper ventilation.

NOTE: All dimensions are in inches.

DTV Back View

HANDLING PRECAUTIONS

• Handle by the cabinet only. Never touch the

screen when handling.

• Excessive pressure on the screen can cause

permanent discoloration or dark spots.

• Handling damage is not covered under

warranty.

Power Requirement: Source: AC 120V, 60Hz AC Power Consumption (average): DP26647: 104 watts

DP32647: 155 watts

SPECIFICATIONS

CAUTION: FCC Regulations state that improper modifications or

unauthorized changes to this unit may void the user’s authority to operate the unit.

Model DP26647

Model DP32647

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

Connect Signal to the DTV’s Integrated Analog / Digital 75 ohm Antenna Input terminal.

GETTING STARTED

(REQUIRED INITIAL SETUP)

Install batteries in remote control (2AAA, not included).

Plug in AC power cord (120V AC, 60 Hz).

Perf orm “All Channel Search.” The All Channel Search will search for off-air digital and analog channels, and analog cable c hannels. The DTV can receive cable or off-air channels, but not at the same time.

If after two searches the DTV still fails to detect any channels, the DTV will tune to Video1.

PRECAUTIONS

To ensure safe operation, please observe the following precautions:

Replace both batteries at the same time. Do

not use a new battery with a used battery. Risk of explosion, if battery is replaced by

an incorrect type. Do not expose the Remote Control Unit to

moisture or

heat.

RF ANTENNA

CABLE

CABLE BOX OR SATELLITE BOX

DTV ANALOG/

DIGITAL

ANTENNA IN

Match the “+” and “–” signs on the batteries with marks inside the remote control.

To 120 V AC outlet.

INITIAL ON-SCREEN

ALL CHANNEL SEARCH

Press the POWER key. (Follow on-screen instructions.)

Note: If EXIT is pressed, the DTV will skip Channel Search and tune to Video1 without storing any channels in the Channel Map databases.

THE

TUNER IN THIS DTV CAN RECEIVE:

1. Digit al and /or Analog Off-Air Signals from an RF antenna.

2. Analog or ClearQAM cable channels.

Note: You must search for ClearQAM channels using

the “Digital Cable Search” menu option.

3. The output from a VCR or cable box.

Digital signals can also be received through the HDMI jacks.

Digital signals from a Set-top (STB) Box should be received through the Video 1, 2, or 3, or HDMI Input1 or 2 jacks.

This DTV can receive ANY unscrambled RF signal being broadcast.



ANALOG CHANNELS

DIGITAL CHANNELS

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

BACK LEFT/RIGHT SIDE PANELS

 S-Video Input (VIDEO1), PAGE 9—To enhance

video detail use the S-Video jack instead of the Video jack, if available on your external equipment. (S-Video connection will override a connection to the Video input jack [VIDEO1]).

 Digital Audio Output, PAGE 8—Use a Phono-

Type (Coaxial) Digital Audio Out Cable to connect Digital Audio Output to an advanced stereo home theater system equipped with Dolby

Digital 5.1.

 Component Video Input (VIDEO2 or VIDEO3),

PAGE 8—Connect digital video equipment to the Y (green), Pb (blue), Pr (red) and Audio L/R jacks. These jacks will automatically detect the type of signal being received.

 Analog Audio Out (L/R) Jacks, PAGE 9—

Connect external audio equipment here

 HDMI INPUT1/2 (High-Definition Multimedia

Interface),P AGE 7—Connect digital video equipment to this jack. It takes only one high-bandwidth cable (not supplied) to communicate between audio/ video equipment and this DTV. HDMI (DVI) INPUT1 jack is compatible with DVI equipped AV devices. (Separate audio connection and an adapter are required for DVI device.)

 Audio/Video Input (VIDEO1), PAGES 9 ~ 10—

Connect analog video equipment here.

Note: S-Video connection overrides the (Video1) com-

posite video connection

 Analog / Digital Antenna Input, PAGE 5—

Connect an RF antenna or Analog Cable system to this jack.

LEFT SIDE PANEL

(see item 8 on page 11)

Volume – + keys

Channel  keys

Power key













RIGHT SIDE

PANEL



+ 12 hidden pages