Samsung VR330S User Manual
Instruction Manual
DVD-VR330,VR330S
English
www.samsung.com
AK68-00995J-00
Warning
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE THE COVER(OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
Getting Started
This symbol indicates “dangerous voltage”
inside the product that presents a risk of
electric shock or personal injury.
This symbol indicates important instructions
accompanying the product.
Do not install this equipment in a confined space such
as a bookcase or similar unit.
WARNING : To prevent damage which may result in fire or
electric shock hazard, do not expose this appliance to rain or moisture.
CAUTION : This DVD Recorder & VCR USES AN INVISI-
BLE LASER BEAM WHICH CAN CAUSE
HAZARDOUS RADIATION EXPOSURE IF
DIRECTED.
BE SURE TO OPERATE RECORDER CORRECTLY AS INSTRUCTED.
CAUTION
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR
YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.
CAUTIONS
Caution: To prevent electric shock, match wide blade of
plug to wide slot, fully insert.
Attention: Pour éviter les chocs électriques, introduíre la
lame la plus large de la fiche dans la borne
correspondante de la prise et pousser jusqu au
fond.
This product satisfies FCC regulations when shielded
cables and connectors are used to connect the unit to
other equipment. To prevent electromagnetic interference
with electric appliances, such as radios and televisions, use
shielded cables and connectors for connections.
FCC NOTE (for U.S.A):
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: FCC regulations state that any unauthorized
changes or modifications to this equipment
may void the user’s authority to operate it.
This unit can be used only where the power
Note
supply is ~100-240V, 60Hz. It cannot be used
elsewhere.
This DVD Recorder & VCR is designed and
manufactured to respond to the Region
Management Information.
If the Region number of a DVD disc does not
correspond to the Region number of this, the
DVD Recorder & VCR cannot play the disc.
This device is protected by U.S. Patent
Nos.4,631,603;4,577,216;4,819,098;4,907,093;
and 6,516,132. This product incorporates copyright protection technology that is protected by
U.S. patents and other intellectual property rights.
Use of this copyright protection technology must
be authorized by Macrovision,and is intended for
home and other limited viewing uses only unless
otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
This product is covered by one or more of the
following U.S. patents:
5,034,830 5,060,200 5,457,669 5,561,649
5,691,858 5,705,762 5,987,417 6,043,912
6,222,983 6,272,096 6,377,524 6,377,531
6,385,587 6,389,569 6,389,570 6,408,408
6,466,532 6,473,736 6,477,501 6,480,829
6,556,520 6,556,521 6,556,522 6,594,208
6,674,697 6,674,957 6,721,493 6,728,474
6,741,535 09/610381 09/610695
2- English
Precaution
Important Safety Instructions
Read these operating instructions carefully before using
the unit. Follow all the safety instructions listed below.
Keep these operating instructions handy for future reference.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings, Install in
accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized
or grounding- type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. if the provided plug does not
fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles, and the point where they exit from the
apparatus.
11) Only use attachments/accessories specified by
the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.
•
Exterior interference such as lightning and static electricity can affect normal operation of this recorder. If
this occurs, turn the DVD Recorder & VCR off and on
again with the POWER button, or disconnect and then
reconnect the AC power cord to the AC power outlet.
The recorder will operate normally.
• Be sure to remove the disc and turn off the recorder after
use.
•
Disconnect the AC power cord from the AC outlet
when you don’t intend to use the recorder for long
periods of time.
•
Clean the disc by wiping in a straight line from the
inside to the outside of the disc.
Maintenance of Cabinet
For safety reasons, be sure to disconnect the AC power
cord from the AC outlet.
•
Do not use benzene, thinner, or other solvents for
cleaning.
•
Wipe the cabinet with a soft cloth.
Disc Handling
•
Use discs with regular shapes.
If an irregular disc (a disc with
a special shape) is used, this
DVD Recorder & VCR may be
damaged.
Holding discs
•
Avoid touching the surface of a disc
where recording is performed.
DVD-RAM, DVD±RW and DVD±R
•
Clean with an optional DVD-RAM/PD
disc cleaner.
Do not use cleaners or cloths for CDs
to clean DVD-RAM/DVD±RW/DVD±R
discs.
DVD-Video, CD
•
Wipe off dirt or contamination on the disc with a soft
cloth.
Getting Started
Handling Cautions
• Before connecting other components to this
recorder, be sure to turn them all off.
• Do not move the recorder while a disc is being
played, or the disc may be scratched or broken,
and the recorder’s internal parts may be damaged.
• Do not put a flower vase filled with water or any
small metal objects on the recorder.
• Be careful not to put your hand into the disc tray.
• Do not place anything other than the disc in the
disc tray.
Cautions on handling discs
•
Do not write on the printed side with a ball-point pen
or pencil.
•
Do not use record cleaning sprays or antistatic. Also,
do not use volatile chemicals, such as benzene or
thinner.
•
Do not apply labels or stickers to discs. (Do not use
discs fixed with exposed tape adhesive or leftover
peeled-off stickers.)
English - 3
•
Do not use scratch-proof protectors or covers.
•
Do not use discs printed with label printers available
on the market.
•
Do not load warped or cracked discs.
Disc Storage
Be careful not to harm the disc because the data on
these discs is highly vulnerable to the environment.
•
Do not keep under direct sunlight.
•
Keep in a cool ventilated area.
•
Store vertically.
•
Keep in a clean protection jacket.
Getting Started
•
If you move your DVD Recorder & VCR suddenly from
a cold place to a warm place, condensation may generate on the operating parts and lens and cause
abnormal disc playback. In this case, do not connect
the plug to the power outlet and wait for two hours.
Then insert the disc and try to play back again. It will
work properly when condensation has evaporated.
Disc Specifications
DVD-Video
•
A digital versatile disc (DVD) can contain up to 135minutes of images, 8 audio languages and 32 subtitle
languages. It is equipped with MPEG-2 picture compression and Dolby 3D surround, allowing you to
enjoy vivid and clear theater quality images in the
comfort of your own home.
•
When switching from the first layer to the second layer
of a double-layered DVD Video disc, there may be
momentary distortion in the image and sound.
This is not a malfunction of the unit.
•
Once a DVD±R/DVD-RW(V) recorded is finalized, it is
playable in a standard DVD player.
Audio CD
•
An audio disc on which 44.1kHz PCM Audio is recorded.
•
Plays CD-DA format audio CD-R and CD-RW discs. This
unit may not be able to play some CD-R or CD-RW discs
due to the condition of the recording.
CD-R/-RW
MP3 CD-R/-RW
•
Only CD-R discs with MP3 files recorded with
ISO9660 or JOLIET format can be played back
•
Only MP3 files with the "mp3" or "MP3" extension can
be used.
•
For MP3 files recorded with a VBR(Variable Bit
Rates), from 80 Kbps to 320 Kbps, the sound may cut
in out.
•
Playable bitrate range is from 56Kbps to 320Kbps.
•
The unit can handle a maximum of 1000 files and folders.
•
DVD-RAM/±RW/±R discs that contain MP3 files can
be played back.
JPEG CD-R/-RW
•
Only JPEG files with the ".jpg", ".JPG" extension can be
used.
•
The unit can handle a maximum of 1000 files and folders.
•
Maximum size of progressive JPEG is 3M pixels.
•
MOTION JPEG is not supported.
•
DVD-RAM/±RW/±R discs that contain JPEG files can be
played back.
Using CD-R/-RW
•
Use a 700MB(80 minutes) CD-R/-RW disc.
If possible, do not use a 800MB(90 minutes) or above
disc, as the disc may not play back.
•
If the CD-R/-RW disc was not recorded as a closed session, you may experience a delay in the early play-back
time, and all recorded files may not play.
•
Some CD-R/-RW discs may not be playable with this unit,
depending on the device which was used to burn them.
For contents recorded on CD-R/-RW media from CDs for
your personal use, playability may vary depending on contents and discs.
DVD±R Disc Playback and Recording
•
Once a DVD±R recorded is finalized, it is playable in a
standard DVD player.
•
You can record onto the available space on the disc and
perform editing functions such as giving titles to discs and
programs and erasing programs before finalizing.
•
When programming is erased from a DVD±R, that space
does not become available. Once an area on a DVD±R is
recorded on, that area is no longer available for recording,
whether the recording is erased or not.
•
It takes about 30 seconds for the unit to complete recording management information after recording finishes.
•
This product optimizes the DVD±R for each recording.
Optimizing is carried out when you start recording after
inserting the disc or turning on the unit. Recording onto
the disc may become impossible if optimizing is carried
out too many times.
•
Playback may be impossible in some cases due to the
condition of recording.
•
This unit can play back DVD±R discs recorded and finalized with a Samsung DVD video recorder. It may not be
able to play some DVD±R discs depending on the disc
and the condition of the recording.
DVD-RW Disc Playback and Recording
•
Recording and playback can be performed on DVDRW discs in both Video and VR Modes.
•
Once a DVD-RW recorded in VR Mode or Video mode
is finalized, you cannot perform additional recording.
•
Once a DVD-RW recorded in Video Mode is finalized,
it becomes DVD-Video.
4- English
•
In both modes, playback can be performed before and after
finalization, but additional recording, deleting and editing can
not be performed after finalization.
•
If you want to record the disc in VR Mode and then record in
V Mode, be sure to execute format. Be careful when executing Format because all the recorded data may be lost.
•
For an unused disc, a message that asks whether to initialize
a disc or not. If you select “Yes”, disc will be formatted in VR
mode.
• DVD-RW (VR mode)
- This is a format that is used for recording data on
DVD-RW disc. You can record multiple titles, edit, delete,
partial delete, create a playlist, etc.
- A disc that is recorded in this mode may not be played
by existing DVD players.
• DVD-RW (Video mode)
-
This is a format that is used for recording data on a
DVD-RW or DVD-R disc. The disc can be played by an
existing DVD player once it has been finalized.
- If a disc that has been recorded in Video mode by a different manufacturer's recorder but has not been finalized
it cannot be played or additionally be recorded by this
recorder.
DVD+RW Disc Playback and Recording
•
With DVD+RW discs, there is no difference between
DVD-Video format (Video mode) and DVD-Video
Recording format (VR mode).
• You can make your own chapters on DVD+RWs and edit
them using the Chapter Edit menu.
• Finalizing is generally unnecessary when using a
DVD+RW disc.
DVD-RAM Disc Playback and Recording
•
For cartridge type DVD-RAM discs, remove the
cartridge and use the disc only.
•
Ensure that the recording mode is set to VR mode.
Otherwise, this product will not be able to play the
recording.
•
You cannot play a DVD-RAM in most DVD players due
to compatibility issues.
•
Only DVD-RAM standard Version 2.0 discs can be
played in this unit.
•
DVD-RAM recorded on this unit may not work with other
DVD Players. To determine compatibility with these DVDRAM discs, refer to the user’s manual for the player.
COPY PROTECTION
•
Many DVD discs are encoded with copy protection. Because of this, you should only connect
your DVD Recorder & VCR directly to your TV,
not to a VCR. Connecting to a VCR results in a
distorted picture from copy-protected DVD discs.
•
This product incorporates copyright protection
technology that is protected by methods claims of
certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology must be authorized by
Macrovision Corporation, and is intended for
home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
Protection
•
Program-protection: See page 73 “Locking a Title”
•
Disc-protection: See page 86 “Disc Protection”
❋ DVD-RAM/
ble with the DVD-VIDEO format cannot be played with
this product.
❋
For more information on DVD recording compatibility,
consult your DVD-RAM/DVD±RW/DVD±R manufacturer.
❋
Use of poor quality DVD-RAM/DVD±RW/DVD±R discs
may cause following unexpected problems including,
without limitation, recording failure, loss of recorded or
edited materials or damage to the recorder.
Do not use the following discs!
•
LD, CD-G, CD-I, CD-ROM and DVD-ROM discs should
not be used in this product.
[Note]
•
Some commercial discs and DVD discs purchased outside your region may not be playable with this product.
When these discs are played, either “No Disc” or “The
disc cannot be played. Please check the regional code
of the disc.” will be displayed.
•
If your DVD-RAM/DVD±RW/DVD±R disc is an illegal
copy or is not in DVD video format, it may also not be
playable.
Disc compatibility
•
A 8X speed DVD+RW or above disc can be played, but
can not be recorded.
•
Not all brands of discs will be compatible with this unit.
•
The latest firmware upgrade to improve recording &
playback quality can be downloaded from our web site.
(Download Center at www.samsung.com)
•
If disc compatibility problems continue, or there is an
issue upgrading your recorder, contact the Call Center at
1-800-SAMSUNG.
DVD±RW/DVD±R discs that are incompati-
Getting Started
English - 5
Contents
Getting Started
Getting Started
Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Getting Started
Precaution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . .3
Handling Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Maintenance of Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . .
Disc Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Disc Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Disc Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Features . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Before Reading the User’s Manual . . . . . . . . . . . . .8
How to use the DVD Recorder & VCR . . . . . . . . . . .9
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Front Panel (DVD-VR330) . . . . . . . . . . . . . . . . . . . . . . .
Rear Panel (DVD-VR330) . . . . . . . . . . . . . . . . . . . . . . .11
Front Panel (DVD-VR330S) . . . . . . . . . . . . . . . . . . . . . .12
Rear Panel (DVD-VR330S) . . . . . . . . . . . . . . . . . . . . . .
Front Panel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tour of the Remote Control . . . . . . . . . . . . . . . . . . . . . .14
Connecting & Setting Up
Connecting & Setting Up
Quick Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Step 1 : Connecting the Antenna Cable . . . . . . . . . .16
Antenna + DVD Recorder & VCR + TV :
No Cable box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Antenna + Cable box + DVD Recorder & VCR + TV :
Cable box with many scrambled channels . . . . . . . . . . .
Antenna + DVD Recorder & VCR + Cable box + TV :
Cable box with a few scrambled channels . . . . . . . . . . .
Step 2 : Connecting the Video Cable . . . . . . . . . . . .19
Connecting to a Video input jack . . . . . . . . . . . . . . . . . .19
Connecting to an S-video input jack . . . . . . . . . . . . . . . .20
Connecting to Component video input jacks (Y,PB,PR) . .21
11
12
1
1
16
17
18
Step 3 : Connecting the Audio Cable . . . . . . . . . . .22
Connecting to your TV . . . . . . . . . . . . . . . . . . . . . . . .
Connecting to a stereo amplifier with
analog input jacks . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting to an AV amplifier with a
digital input jack . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 4 : Connecting External Devices . . . . . . . . . .25
Connecting a VCR, Set-Top Box(STB) or
2
3
4
3
3
3
DVD player to the AV 1 IN or S-VIDEO IN jacks . . . . .
Connecting a Camcorder to the AV 2 IN jacks . . . . . .26
Connecting a Camcorder to the DV IN jack . . . . . . . .27
Step 5 : Connecting the Power Cord . . . . . . . . . . .28
Step 6 : Preparing the Remote Control . . . . . . . . .28
Setting the Remote Control . . . . . . . . . . . . . . . . . . . . .29
System Setup
System Setup
On-Screen Menu Navigation . . . . . . . . . . . . . . . . .30
Auto Clock Set . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Manual Clock Set . . . . . . . . . . . . . . . . . . . . . . . . .32
Channel Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Auto Channel Memory . . . . . . . . . . . . . . . . . . . . . .33
Channel Add/Delete . . . . . . . . . . . . . . . . . . . . . . .34
RF Output Channel . . . . . . . . . . . . . . . . . . . . . . . .34
Setting Up the Language Options . . . . . . . . . . . . .35
Setting Up the Audio Options . . . . . . . . . . . . . . . .36
Setting Up the Display(Video) Options . . . . . . . . . .37
Setting Up the Parental Control . . . . . . . . . . . . . . .38
VCR Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Video Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
DVD EP Mode Time . . . . . . . . . . . . . . . . . . . . . . .41
Automatic Chapter Creator . . . . . . . . . . . . . . . . . .41
Quick Recording . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Playback
Playback
DVD Playback
Before Playing . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Using the Disc Menu and Title Menu . . . . . . . . . . .45
Using the Search & Skip Functions . . . . . . . . . . . .45
Slow Motion Play / Step Motion Play . . . . . . . . . . .46
About ANYKEY . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Repeat Playback . . . . . . . . . . . . . . . . . . . . . . . . . .47
22
23
24
25
6- English
Selecting the Subtitle & Audio Language . . . . . . . .48
Changing the Camera Angle . . . . . . . . . . . . . . . . .49
Zooming-In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Using the Bookmarks . . . . . . . . . . . . . . . . . . . . . .50
Using the Markers . . . . . . . . . . . . . . . . . . . . . . . . .51
Playing back an Audio CD (CD-DA) . . . . . . . . . . . .52
Playing back an MP3 Disc . . . . . . . . . . . . . . . . . . .53
Repeat Playback of an Audio/MP3 Disc . . . . . . . .54
Play Option Mode . . . . . . . . . . . . . . . . . . . . . . . . .54
To Program Tracks . . . . . . . . . . . . . . . . . . . . . . . . .55
Playing a Picture Disc . . . . . . . . . . . . . . . . . . . . . .55
VCR Playback
Playing the VCR . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Special VCR Playback Features . . . . . . . . . . . . . .57
S-VHS Playback . . . . . . . . . . . . . . . . . . . . . . . . . .57
Variable Search System . . . . . . . . . . . . . . . . . . . . .57
Recording
Recording
DVD Recording
Before Recording . . . . . . . . . . . . . . . . . . . . . . . . .59
Recordable discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Recording Formats . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recording Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Unrecordable video . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Recording the Current Channel you are watching
60
. .61
Recording from External Devices . . . . . . . . . . . . . .62
Recording through a DV Input jack . . . . . . . . . . . .62
Making a One Touch Recording(OTR) . . . . . . . . . .63
Making a Timer Recording . . . . . . . . . . . . . . . . . . .63
Editing the Scheduled Record List . . . . . . . . . . . . .65
Deleting the Scheduled Record List . . . . . . . . . . . .65
VCR Recording
Basic VCR Recording . . . . . . . . . . . . . . . . . . . . . .66
Check Remaining Time . . . . . . . . . . . . . . . . . . . . .67
Special Recording Features . . . . . . . . . . . . . . . . .67
Copy to DVD or VCR . . . . . . . . . . . . . . . . . . . . . . .68
Editing
Editing
Playing the Title List . . . . . . . . . . . . . . . . . . . . . . . .70
Basic Editing (Title List) . . . . . . . . . . . . . . . . . . . . .72
Renaming(Labeling) a Title . . . . . . . . . . . . . . . . . . . . .72
Locking(Protecting) a Title . . . . . . . . . . . . . . . . . . . . . .73
Deleting a Title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Deleting a Section of a Title . . . . . . . . . . . . . . . . . . . .74
Editing a Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Dividing a Title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Advanced Editing (Playlist) . . . . . . . . . . . . . . . . . . .79
Creating a Playlist . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Playing Titles in the Playlist . . . . . . . . . . . . . . . . . . . . .80
Renaming a Playlist Title . . . . . . . . . . . . . . . . . . . . . . .80
Editing a Scene for the Playlist . . . . . . . . . . . . . . . . . .
Copying a Playlist Title to the VCR . . . . . . . . . . . . . . .84
Deleting a Playlist Title from the Playlist . . . . . . . . . . .
81
85
Disc Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Editing the Disc Name . . . . . . . . . . . . . . . . . . . . . .85
Disc Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Formatting a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Finalizing a disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Unfinalizing a disc (V/VR mode) . . . . . . . . . . . . . . . . .
Delete All Title Lists . . . . . . . . . . . . . . . . . . . . . . . . . . .89
Edit Compatible . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Reference
Reference
86
88
Troubleshooting
(DVD-VIDEO/DVD-RAM/DVD±RW/DVD±R) . . . . .92
Troubleshooting (DVD) . . . . . . . . . . . . . . . . . . . . . .93
Troubleshooting (VCR) . . . . . . . . . . . . . . . . . . . . .94
Problems and Solutions (Display error message)
. .95
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
Getting Started
English - 7
General Features
Before Reading the User’s Manual
The DVD-VR330, VR330S allows you to record and play
high quality digital video on DVD-RAM/DVD±RW/DVD±R
discs. You can record and edit digital video on DVD-RAM/
DVD±RW/ DVD±R discs as if they were VCR tapes.
Getting Started
High quality digital audio and video recording and
playback
You can record up to approximately 16-hours of video on a
double side 9.4 GB DVD-RAM disc,up to 15-hours on a
dual-layer 8.5GB DVD±R disc, and up to 8-hours on a 4.7
GB DVD-RAM/DVD±RW/DVD±R disc, depending on the
recording mode.
Creating DVD video titles using DVD±RW/DVD±R discs
With the DVD-VR330, VR330S, you can create your own
DVD video titles on 4.7 GB DVD±RW/DVD±R or 8.5GB
DVD±R discs.
A Variety of Recording Options
Select an appropriate recording mode between XP, SP, LP
and EP to meet your recording needs. (See page 60.)
• XP mode - High quality, about 1 hour
• SP mode - Standard quality, about 2 hours
• LP mode - Low quality, about 4 hours
• EP mode - Lower quality, about 6 or 8 hours
- The dual layer DVD±Rs have approximately double the
capacity of single layer DVD±Rs. (See page 43.)
Copying digital camcorder content using DV input jack
Record digital camcorder images onto DVD-RAM/DVD±
RW/DVD±R discs or video tape using the DV input jack
(IEEE 1394-4pin). (See page 62.)
High quality progressive scan
Progressive scanning provides high resolution and flicker
free video. The 10-bit 54-MHz DAC, 2D Y/C Separating circuitry and Time Base Corrector processor technology provide you with the highest image playback and recording
quality. (See page 21.)
Component progressive scan output video is available in
both DVD and VCR modes.
A variety of functions with easy-to-use user interface
Integrated menu system and messaging functionality allow
you to perform the desired operations easily and conveniently. With a DVD-RAM/DVD-RW(VR mode) disc, you
can edit recorded images, create playlist, and edit video in
specific sequence according to your needs.
Make sure to check the following terms before reading
the user’s manual.
Icons that will be used in manual
Icon Term Definition
This involves a function available
DVD
RAM
-RW
-R
+RW
+R
CD
JPEG in CD-R/-RW or DVD±R/±RW/
MP3 in CD-R/-RW or DVD±R/±RW/
Caution function does not operate or
NOTE on the page that help each
One-Touch
button
ANYKEY A function that can be operated
button by using ANYKEY button.
in DVD or DVD-R/DVD-RW(V)/+R
discs that have been recorded
and finalized.
This involves a function available
in DVD-RAM.
This involves a function available
in DVD-RW.
This involves a function available
in DVD-R.
This involves a function available
in DVD+RW.
This involves a function available
in DVD+R.
This involves a function available
in a data CD (CD-R or CD-RW).
This involves a function available
-RAM discs.
This involves a function available
-RAM discs.
This involves a case where a
settings may be cancelled.
This involves tips or instructions
function operate.
A function that can be operated
by using only one button.
Copyright
©2006 Samsung Electronics Co.
All rights reserved; No part or whole of this user’s
manual may be reproduced or copied without the prior
written permission of Samsung Electronics Co.
8- English
About the use of this user’s manual
1) Be sure to be familiar with Safety Instructions before
using this product. (See pages 2~5)
2) If a problem occurs, check the Troubleshooting.
(See pages 92~94)
How to use the DVD
Step 3
Recording
Recorder & VCR
Step 1
This unit can record on the following types of discs.
If you want to repeatedly record on the same disc or
you want to edit the disc after recording, select a
rewritable DVD±RW or DVD-RAM type disc. If you
want to save a recording without any changes,
choose a non-rewritable DVD±R.
Step 2
Unlike a VCR, the recorder automatically starts formatting when an unused disc is inserted. This is required
for the preparation of recording on a disc.
Using a DVD-RAM
This type of disc can be formatted in DVD-Video
Recording format (VR mode). You can edit recorded
images and create a playlist in a specific sequence
according to your requirements.
Using a DVD±RW/+R
•
When an unused DVD±RW/+R disc is first inserted,
the message "Uninitialized Disc. Do you want to initialize this disc?" will be displayed.
If you select Yes, initializing will be start. DVD-RW
disc can be formatted in either DVD-Video format
(Video mode) or DVD-Video Recording format (VR
mode)
•
With DVD+RW discs, there is no difference between
DVD-Video format (Video mode) and DVD-Video
Recording format (VR mode).
Using a DVD-R
Initializing disc is unnecessary and only V mode
Recording is supported. You can play this type of disc
on various DVD components only when they have
been finalized.
Select the disc type
Format the disc to start recording
There are two different recording methods: Direct
Recording and Timer Recording. Timer recording is
classified as a Date : Once, Daily or Weekly.
Recording mode : XP (high quality mode), SP (standard quality mode), LP (long recording mode), and
EP (extended mode).
Step 4
You can select the title you want to play in a displayed
menu and then immediately start playback.
A DVD consists of sections called titles, and sub sections called chapters.
During recording, a title is created between two points
where you start and stop recording. Chapters will be
created automatically when you finalize recording on
DVD-R / DVD-RW discs in Video mode.
You can make your own chapters on DVD+RWs and
edit them using the Chapter Edit menu.
The chapter’s length (interval between chapters) varies
according to the recording mode.
Step 5
Editing on discs is easier than conventional video
tapes. The recorder supports many different edit functions, possible only with DVDs.
With a simple and easy edit menu, you can operate
various edit functions, such as delete, copy, rename,
lock, etc., on a recorded title.
Creating a playlist (DVD-RAM/-RW in VR mode)
With this recorder, you can create a new playlist on
the same disc and edit it without changing the
original recording.
Playing
Editing a recorded disc
Getting Started
Note
■
You can only use either the VR or Video
mode on a DVD-RW, but not both at the
same time.
■
You can format a DVD-RW to V or VR
mode using disc manager.
It should be noted that the disc's data will
be lost when changing formats.
English - 9
Step 6
To play your DVD on other DVD players, finalizing
may be necessary. First, finish all editing and recording operations, then finalize the disc.
When using a DVD-RW disc in VR Mode
Although finalizing is generally unnecessary when
playing the disc on a VR Mode compatible component, a finalized disc should be used for playback.
Getting Started
When using a DVD-RW disc in Video Mode
The disc should be finalized first to enable playback
on anything other than this recorder. No more editing
or recording can be made on the disc once it has
been finalized.
When using a DVD±R disc
You should finalize the disc to play it on a component
other than this recorder. You cannot edit or record on
the disc once it has been finalized.
Finalizing & Playing on
other DVD components
10 - English
Description
Front Panel (DVD-VR330)
Getting Started
1 2 3
5
6 87
1. DVD DECK
2. DVD OPEN/CLOSE BUTTON
3. VCR DECK
4. VCR EJECT BUTTON
5. POWER BUTTON
6. VIDEO INPUT JACK (AV 2 IN)
7. AUDIO L, R INPUT JACKS (AV 2 IN)
8. DV INPUT JACK
Rear Panel
(DVD-VR330)
4
9
10 11 14 15
9. P.SCAN BUTTON
10. FRONT PANEL DISPLAY
11. DVD/VCR SELECT BUTTON
12. COPY BUTTON
13. CHANNEL / BUTTONS
14. RECORD BUTTON
15. PLAY/STILL, REW/SKIP, F.F/SKIP, STOP
BUTTONS
1
12 13
2 3
Fan
The fan always revolves when the power is on.
Ensure a minimum of 4” clear space on all sides of the fan
when installing the product.
1. VIDEO INPUT JACK (AV 1 IN)
2. VIDEO OUT JACK (AV OUT)
3. AUDIO OUT JACKS
(COMPONENT OUT)
4. S-VIDEO IN/OUT JACKS
5. ANT IN JACK
6 7 8
5
4
6. ANT OUT (TO TV) JACK
7. AUDIO INPUT JACKS (AV 1 IN)
8. AUDIO OUT JACKS (AV OUT)
9. DIGITAL AUDIO OUT JACK (OPTICAL)
10. DIGITAL AUDIO OUT JACK (COAXIAL)
11. VIDEO OUT JACKS (COMPONENT OUT)
9
10 11
English - 11
Front Panel (DVD-VR330S)
Getting Started
1. DVD DECK
2. DVD OPEN/CLOSE BUTTON
3. VCR DECK
4. VCR EJECT BUTTON
5. POWER BUTTON
6. VIDEO INPUT JACK (AV 2 IN)
7. AUDIO L, R INPUT JACKS (AV 2 IN)
8. DV INPUT JACK
Rear Panel
1 2 3
5
6 87
(DVD-VR330S)
4
9
10 11 14 15
12 13
9. P.SCAN BUTTON
10. FRONT PANEL DISPLAY
11. DVD/VCR SELECT BUTTON
12. COPY BUTTON
13. CHANNEL / BUTTONS
14. RECORD BUTTON
15. PLAY/STILL, REW/SKIP, F.F/SKIP, STOP
BUTTONS
Fan
The fan always revolves when the power is on.
Ensure a minimum of 4” clear space on all sides of the fan
when installing the product.
1. VIDEO INPUT JACK (AV 1 IN)
2. VIDEO OUT JACK (AV OUT)
3. AUDIO OUT JACKS
(COMPONENT OUT)
4. S-VIDEO IN/OUT JACKS
5. ANT IN JACK
2 3
1
6 7 8
5
4
9
10 11
6. ANT OUT (TO TV) JACK
7. AUDIO INPUT JACKS (AV 1 IN)
8. AUDIO OUT JACKS (AV OUT)
9. DIGITAL AUDIO OUT JACK (OPTICAL)
10. DIGITAL AUDIO OUT JACK (COAXIAL)
11. VIDEO OUT JACKS (COMPONENT OUT)
12 - English
Front Panel Display
1 4 5 6
1. DVD is activated.
2. DVD-RAM is activated.
3. DVD(±)R or DVD(±)RW is actived.
4. Progressive Scan mode is activated.
5. Record function is activated.
6. VCR is activated.
32
87 9
7. DVD or CD media is loaded.
8. The time, counter position or current deck
status is indicated.
9. When you set a Timer recording,
this indicator appears.
10. VHS videotape is loaded.
Getting Started
10
Unpacking
Accessories
Check for the supplied accessories below.
Audio/Video Cable
RF Cable for TV EP-2 Plug Converter
Remote Control
Batteries for Remote
Control (AAA Size)
User’s Manual
Quick Guide
English - 13
Tour of the Remote Control
1
2
3
4
Getting Started
5
6
7
8
9
10
11
12
13
14
15
16
17
1. DVD Button
Press this when you use a DVD.
2. TV Button
Press this to operate TV.
3. POWER Button
4. NUMBER Button
5. 100+ Button
Press this to select channel 100 or higher.
6. F.ADV/SKIP Button
7. Playback-related Buttons
Forward/Rewind, Search, Skip, Stop, Play/Pause
8. VOL (Volume) Button
TV volume adjustment
9. MENU Button
Press this to bring up the DVD Recorder & VCR’s
setup menu.
10. ENTER/DIRECTION Buttons
(UP/DOWN or LEFT/RIGHT Buttons)
This button functions as a toggle switch.
11. INFO Button
Press this to display current setting or disc status.
12. TITLE LIST/DISC MENU Button
Press this to enter the TITLE LIST/Disc menu.
14 - English
❋ This is a special remote control for the visually impaired, and has Braille points on the
POWER( ), STOP( ) and PLAY( ) buttons.
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
13. SUBTITLE Button
Press this to switch the DVD’s subtitle language.
14. ANYKEY Button
Press this to set the status of the disc that is being
played.
15. REC Button
Press this to make a recording on VCR, DVD-RAM/
±RW/±R discs.
16. TO DVD COPY Button
Press this when you copy from the VCR to the
DVD.
17. REC SPEED Button
Press this to set the desired recording time and
picture quality.
18. VCR Button
Press this when you use a VCR.
19. INPUT SEL. Button
Press this to select AV input signal in external input
mode. (Tuner, AV input, DV input)
20. OPEN/CLOSE Button
Press this to open and close the disc tray.
21. TV POWER Button
22. TV/VCR Button
23. MARKER Button
Press this to bookmark or mark a position while
playing a disc.
24. CH/TRK Button
Press this to select a TV channel/Adjust tape
tracking.
25. RETURN Button
Returns to a previous menu.
26. AUDIO/TV MUTE Button
Press this to access various audio functions.
This operates as sound mute. (TV mode)
27. CANCEL Button
28. PLAY LIST/TITLE MENU Button
Press this to enter the Edit playlist/Title menu.
29. ANGLE Button
Press this to access various camera angles on a
disc (if the disc contains multiple camera angles).
30. ZOOM Button
Zooms in on screen.
31. TIMER REC Button
Press this when you use Timer Recording.
32. TO VCR COPY Button
Press this when you copy from the DVD to the VCR.
33. REC PAUSE Button
Press this to pause during recording.
❚ Key Lock Function
If you do not want others to operate the DVD Recorder &
VCR (for example if you have programmed a timer recording)
you can set the equipment to lock out all button controls.
• Press and hold the INFO button on the remote control for 5
seconds.
The display will show “SAFE” when the feature is activated.
• To resume normal mode, press and hold the INFO button
again for 5 seconds.
“SAFE” will disappear and the DVD Recorder & VCR will
operate normally.
Connecting & Setting Up
Quick Overview
A Quick overview presented in this guide will give you
enough information to start using the recorder.
Connections
Step 1 : Connecting the Antenna Cable
†
Step 2 : Connecting the Video Cable
†
Step 3 : Connecting the Audio Cable
†
Step 4 : Connecting External Devices
†
Quick Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Step 1: Connecting the Antenna Cable . . . . . . . . . . . . . . . . .16
Step 2 : Connecting the Video Cable . . . . . . . . . . . . . . . . . .19
Step 3 : Connecting the Audio Cable . . . . . . . . . . . . . . . . . .22
Step 4 : Connecting External Devices . . . . . . . . . . . . . . . . . .25
Step 5 : Connecting the Power Cord . . . . . . . . . . . . . . . . . . .28
Step 6 : Preparing the Remote Control . . . . . . . . . . . . . . . . .28
Step 5 : Connecting the Power Cord
†
Step 6 : Preparing the Remote Control
•
Note to CATV system installer :
to call CATV system installer’s attention to Article 820-40
of the National Electrical Code (Section 54 of Canadian
Electrical Code, Part I), that provides guidelines for
proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding
system of the building as close to the point of cable title
as practical.
This reminder is
English - 15
Step 1: Connecting the Antenna Cable
There are several ways to connect your DVD Recorder & VCR. Select the antenna connection that best suits you below.
Antenna + DVD Recorder & VCR + TV : No Cable box
You can record non-scrambled channels by selecting the channel on the DVD Recorder & VCR. Also use this
method if you watch channels without cable box.
Connections
■
If you are using an off-air antenna that has 300-
Note
ohm twin flat leads, use an external antenna
connector (300-75 ohm adaptor : not supplied)
to connect the antenna to the DVD Recorder &
VCR.
16 - English
Note
■
If you have two separate antennas (one VHF
and the other UHF), use a UHF/VHF combineradaptor (available at most electronics shops) to
connect the antenna to the DVD Recorder &
VCR.
Antenna + Cable box + DVD Recorder & VCR + TV : Cable box with many scrambled channels
You can record channels by selecting the channel on the cable box. You cannot record one channel while watching
another channel. Be sure that the cable box is turned on.
Connections
English - 17
Antenna + DVD Recorder & VCR + Cable box + TV : Cable box with a few scrambled channels
You can record non-scrambled channels by selecting the channel on the cable box. You cannot record scrambled
channels that require a cable box.
Connections
18 - English
Step 2 : Connecting the Video Cable
INPUT
R
L
AUDIO
White
Red
VIDEO
Yellow
Audio/Video
Cable
There are several ways to connect your DVD Recorder & VCR. Select one of the video connections on the following pages.
You must use one of the following audio/video connections on this unit.
Connecting to a Video input jack
Connect a video(yellow) cable between the VIDEO(yellow) OUT jack on DVD Recorder & VCR and VIDEO(yellow)
IN jack on the TV (or AV amplifier).
Connections
• You will enjoy regular quality images.
• Connect audio cables(white and red) between the
AUDIO OUT jacks on the DVD Recorder & VCR and
AUDIO IN jacks on TV(or AV amplifier).
(See pages 22 ~ 24)
English - 19
S-Video Cable
(not supplied)
INPUT
S-VIDEO
Connecting to an S-Video input jack
Connect an S-Video cable(not supplied) between the S-VIDEO OUT jack on DVD Recorder & VCR and S-VIDEO
IN jack on your TV (or AV amplifier).
Connections
• You will enjoy high quality images. S-Video separates
the picture element into black and white (Y) and color
(C) signals to present clearer images than regular
video input mode.
• Connect audio cables(white and red) between the
AUDIO OUT jacks on the DVD Recorder & VCR and
AUDIO IN jacks on TV(or AV amplifier).
(See pages 22 ~ 24)
20 - English
Note
■
S-Video and Component video output are
available only if your TV supports S-Video
input or Component video input, respectively.
If S-Video or Component video output does
not work, check the TV connections and the
TV input selection settings.
Component Cable
(not supplied)
COMPONENT
P
R
P
B
Y
green
blue
red
green
blue
red
Connecting to Component video input jacks (Y,PB,PR)
Connect Component video cables (not supplied) between the COMPONENT OUT (Y,PB,PR) jacks on
B,PR
DVD Recorder & VCR and COMPONENT IN (Y,P
) jacks on your TV (or AV amplifier).
Connections
• You will enjoy high quality accurate color reproduction
images. Component video separates the picture
B
element into black and White(Y), blue(P
), red(PR)
signals to present clear and clean images.
• Connect audio cables(white and red) between the
Component AUDIO OUT jacks on the DVD Recorder &
VCR and Component AUDIO IN jacks on TV(or AV
amplifier). (See pages 22 ~ 24)
• Progressive scan
- If the your TV supports Progressive Scan, you can
enjoy higher quality video by pressing the P.SCAN
button. (The component cable has to be connected.)
1. With the unit in stop mode, press the P.SCAN but-
ton on the front of the DVD Recorder & VCR.
2. The message ‘Press “Yes” to confirm Progressive
scan mode. Otherwise press “No”’ will appear.
œ √
Press the
buttons to select Yes, and then
press the ENTER button.
Note
■
Compared to standard interlaced video, progres-
sive scan doubles the amount of video lines fed to
your TV, resulting in a more stable, flicker-free,
and clear image than interlaced video. The progressive scan video output jack is used in progressive output mode. This is only available with
TVs that support progressive scan.
■
Progressive Scan Output (480p) Consumers
should note that not all high definition television
sets are fully compatible with this product and may
cause artifacts to be displayed in the picture.
If you experience 480p progressive scan picture
problems, it is recommended that you switch the
connection to the ‘standard definition’ output. If
there are questions regarding TV set compatibility
with this model, please contact our customer
service center at 1-800-SAMSUNG.
English - 21
Step 3 : Connecting the Audio Cable
INPUT
AUDIO
R
L
Red
White
VIDEO
Yellow
Audio/Video
Cable
Select one of the Audio connections on the following pages.
Connecting to your TV
This connection will use your TV’s speakers.
Connections
22 - English
Audio/Video
Cable
INPUT
ANALOG AUDIO
RL
Red White
Connecting to a stereo amplifier with analog input jacks
If your stereo amplifier only has AUDIO INPUT jacks(L and R), use the AUDIO OUT jacks.
Front(L)speaker Front(R)speaker
Connections
English - 23
Optical Cable
(not supplied)
Coaxial Cable
(not supplied)
INPUT
Digital Audio
or
AV amplifier
Connecting to an AV amplifier with a digital input jack
If your AV amplifier has a Dolby Digital or DTS decoder and a digital input jack, use this connection.
To enjoy Dolby Digital or DTS sound, you will need to set up the audio settings. (See page 36)
Connections
24 - English
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
Step 4 : Connecting External Devices
AUDIO VIDEOS-VIDEO
R
L
S-Video Cable
(not supplied)
Audio/Video
Cable
OUTPUT
or
This allows you to connect your DVD Recorder & VCR to other external devices and view or record their outputs.
Connecting a VCR, Set-Top Box(STB) or DVD player to the AV 1 IN or S-VIDEO IN jacks
Connecting a VCR or external device to AV 1 IN jacks of the DVD Recorder & VCR.
You can record from connected equipment (VCR, STB or DVD).
Connections
■ You can also use the AV 2 IN jacks on the
Note
front panel of the DVD Recorder & VCR.
■ Press the INPUT SEL. button to select the
AV1 or S-Video input.
■ Copy protected content cannot be recorded.
■ Depending on your input connection, you
must choose AV 1 (Composite) or S-video.
(See page 40)
English - 25
AUDIOVIDEO
R
L
OUTPUT
Audio/Video
Cable
Camcorder
Connecting a Camcorder to the AV 2 IN jacks
You can also use the AV 2 IN jacks on the front panel of the DVD Recorder & VCR. You can record from connected
equipment, such as a camcorder. When an input source is inserted into AV 2 IN while viewing TV, the input will be
switched to AV 2 IN automatically.
Connections
26 - English
■ If the AV 2 In input source is not selected
Note
automatically, press the INPUT SEL. button
to select the AV 2 input.
DV OUT
DV Cable
(not supplied)
Camcorder
Connecting a Camcorder to the DV IN jack
If your camcorder has a DV output jack, connect it to the DV input jack of your DVD Recorder & VCR.
Connections
■
If the input is not selected automatically, use
INPUT SEL. button to select proper input.
Note
English - 27
Step 5 : Connecting
Step 6 : Preparing the
the Power Cord
After all connections are complete, plug the power cord
in the wall outlet.
“Auto” appears in the front panel display. This
means that the current time is being set automatically through the antenna under connection(Auto
Program). The setup may take several minutes.
When the DVD Recorder & VCR operates normally, the
current time is automatically set and displayed in the
front panel display.
Connections
Remote Control
Install Batteries in the Remote Control
• Open the battery cover on the back of the
remote control.
• Insert two AAA batteries. Make sure that the polarities
(+ and -) are aligned correctly.
• Replace the battery cover.
If the remote control does not operate
properly:
• Check the polarity + - of the batteries (Dry-Cell)
• Check if the batteries are drained.
• Check if the remote sensor is blocked by obstacles.
• Check if there is any fluorescent lighting nearby.
Dispose of batteries according to local
environmental regulations. Do not put them in
the household trash.
28 - English
Setting the Remote Control
You can control part of another manufacturer’s TV
functions with this remote control.
• Buttons that can be controlled on your TV :
TV POWER, INPUT SEL., VOL
TV MUTE, 0~9, 100+.
+
/-, CH/TRK ( / ),
To determine whether your television is
compatible, follow the instructions below.
1. Switch your television on.
2. Point the remote control towards the television.
3. Press and hold the TV button and enter the two-figure
code simultaneously corresponding to the brand of
your television by pressing the appropriate number
buttons.
Brand Codes
SAMSUNG
DAEWOO 19
EMERSON 21
GRADIENTE 30
HITACHI 10
JVC 11
LG 06,08,18
LOEWE 28
MAGNAVOX 04
MITSUBISHI 13
01,14,15,23,31
Brand Codes
NEWSAN 27
NOBLEX 25
PANASONIC 12,24
RCA 07,29
SANYO 05,20
SHARP 02,16,22
SONY 03
TELEFUNKEN 26
TOSHIBA 09
ZENITH 17
Result: If your television is compatible with the remote
control, it will switch off.
It is now programmed to operate with the remote
control.
■
If several codes are indicated for your
television brand, try each one in turn until you
Note
find one that works. If you replace the remote
control’s batteries, you must set the brand code
again.
You can then control the television using the
following buttons.
Connections
Button Function
TV POWER Used to switch the television on and off.
INPUT SEL. Used to select an external source.
VOL+/
-
Used to adjust the volume of the television.
CH/TRK
(/)
Used to select the desired channel.
TV MUTE Used to toggle the sound on and off.
0~9 Used to input number directly.
100+ Used to select channels over 100.
The various functions may be able to be
controlled on all televisions. If you encounter
Note
problems, operate the television directly.
English - 29
On-Screen Menu
System Setup
System Setup
Navigation
The on-screen menus allow you to enable or disable
various functions on your DVD Recorder & VCR.
Use the following buttons to open and navigate through
the on-screen menus.
DVD-Recorder
No Disc
Timer Rec.
Timer Record
Scheduled Record List
Setup
MENU Button
1
Press this button on the remote control to open
the on-screen MENU. Press again to exit the
on-screen MENU.
…/†,œ /√ Buttons
2
Press these buttons on the remote control to
move the selection bar …/†,œ /√ to cycle through
the menu options.
Timer Record
√√
√√
RETURNENTERMOVE EXIT
On-Screen Menu Navigation..............................................30
Auto Clock Set ..................................................................31
Manual Clock Set ..............................................................32
Channel Set .......................................................................33
Auto Channel Memory.......................................................33
Channel Add/Delete ..........................................................34
RF Output Channel............................................................34
Setting Up the Language Options .....................................35
Setting Up the Audio Options ...........................................36
Setting Up the Display (Video) Options ............................37
Setting Up the Parental Control........................................38
VCR Setting ......................................................................39
Video Input .......................................................................40
DVD EP Mode Time .........................................................41
Automatic Chapter Creator...............................................41
Quick Recording.................................................................42
30 - English
ENTER Button
3
Press this button on the remote control to confirm
any new settings.
RETURN Button
4
Press this button on the remote control to return to
the previous MENU screen displayed or to exit the
on-screen MENU.
Loading...