Samsung VR2AM7090WD User Manual

POWERbot

User manual

SR1AM70****, SR2AM70**** Series

• Before operating this unit, please read the instructions carefully.

• For indoor use only.

Contents

Safety information

Installation

Accessories / Installation note

Charging

Automatic charging / Recharging / Low battery (Lo)

Using POWERbot

Turning the power on/off / Selecting cleaning modes/ Using special cleaning functions/ About the boundary markers/ Using Energy-saving mode

Using the remote control

Name of each part

Top / Bottom / Display panel

Setting time/schedule

Setting the time / Setting the schedule

Cleaning and maintaining

Cleaning the dustbin / Cleaning the sensors and the camera / Cleaning the brush and Auto shutter tool / Cleaning the Driving wheel

SmartThings App

Notes and cautions

Charging / Using / Cleaning and maintenance / About the battery / About the IrDA sensor

Information codes

Troubleshooting

Open Source Announcement

Specications

ENGLISH-02

Safety information

SAFETY INFORMATION

• Before operating the appliance, please read this manual thoroughly and

WARNING

CAUTION/WARNING SYMBOLS USED

retain it for your reference.

• Because the following operating instructions cover various models, the

characteristics of your vacuum cleaner may differ slightly from those described in this manual.

WARNING

CAUTION

Indicates that a danger of death or serious injury exists.

Indicates that a risk of personal injury or material damage exists.

OTHER SYMBOLS USED

Indicates that the following text contains additional important

NOTE

information.

State of California Proposition 65 Warning (US only)

This product contains chemicals known to the State of California to cause

WARNING

cancer and birth defects or other reproductive harm.

L i - i o n

For battery recycling go to call2recycle.org or call 1-800-822-8837

ENGLISH-03

Safety information

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should be observed, including the following:

READ ALL INSTRUCTIONS BEFORE USING YOUR POWERbot.

Unplug from outlet when not in use and before conducting maintenance.

WARNING: To reduce the risk of re, electric shock, or injury:

GENERAL

• Use only as described in this manual.

• Do not operate POWERbot or the battery charger / docking station if it has been damaged in any way.

• If the vacuum cleaner is not working as it should, has been dropped, damaged, left outdoors, or dropped in water, contact an authorized Samsung service center.

• Do not handle the battery charger / docking station or POWERbot with wet hands.

• Use only on dry, indoor surfaces.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Do not let children clean or perform user maintenance on the POWERbot without adult supervision.

• Place the cords from other appliances out of the area to be cleaned.

• Do not operate the vacuum in a room where an infant or child is sleeping.

• Do not operate the vacuum in an area where there are lit candles or fragile objects on the oor.

• Do not operate the vacuum in a room that has lit candles on furniture that the vacuum may accidentally hit or bump into.

• Do not allow children to sit on the vacuum.

• Do not use the vacuum on a wet surface.

Battery charger / Docking station

• Do not modify the polarized plug to t a non-polarized outlet or extension cord.

• Do not use outdoors or on wet surfaces.

• Unplug the battery charger / docking station from the outlet when not in use and before servicing.

• Use only the battery charger / docking station supplied by the manufacturer to recharge the POWERbot.

• Do not use with a damaged cord or plug or a loose power outlet.

• Do not pull or carry by the cord, use the cord as a handle, close the door on the cord, or pull the cord around sharp edges or corners. Keep the cord away from heated surfaces.

ENGLISH-04

• Do not use extension cords or outlets with inadequate current carrying capacity.

• Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.

• Do not mutilate or incinerate batteries as they will explode at high temperatures.

• Do not attempt to open the battery charger / docking station. Repairs should only be carried out by a qualied Samsung service center.

• Do not expose the battery charger / docking station to high temperatures or allow moisture or humidity of any kind to come into contact with the battery charger / docking station.

POWERbot

• Do not use to pick up hard or sharp objects such as glass, nails, screws, coins, and etc.

• Do not use without a lter in place. When servicing the unit, never put ngers or other objects into the fan chamber in case the unit accidentally turns on.

• Do not put any objects into openings. Do not use with any openings blocked; keep openings free of dust, lint, hair, and anything that may reduce air ow.

• Do not use to pick up toxic materials (chlorine bleach, ammonia, drain cleaner, etc.).

• Do not use to pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

• Do not use to pick up ammable or combustible liquids such as gasoline or use in areas where they may be present. Also do not use in:

– Locations with candles or desk lamps on the oor. – Locations with unattended res (re or embers). – Locations with distilled alcohol, thinner, ashtrays with burning cigarettes, etc.

• Do not use POWERbot in an enclosed space lled with vapors given off by oil based paint, paint thinner, moth proong substances, ammable dust, or other explosive or toxic vapors.

• Leaks from battery cells can occur under extreme usage or temperature conditions. If the liquid gets on skin, wash quickly with water. If the liquid gets into eyes, ush them immediately with clean water for a minimum of 10minutes. Seek medical attention.

SAVE THESE INSTRUCTIONS

POLARIZED PLUG INSTRUCTIONS

• To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will t in a polarized outlet only one way. If the plug does not t fully in the outlet, reverse the plug. If it still does not t, contact a qualied electrician to install a proper outlet. Do not modify the plug in any way.

ENGLISH-05

Safety information

REGULATORY NOTICE

1. FCC Notice

CAUTION

FCC STATEMENT:

FCC CAUTION:

• Any changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

• This device complies with Part 15 of FCC Rules. Operation is Subject to following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received including interference that

cause undesired operation.

• For products available in the US and Canadian markets, only channels 1~11 are available. You cannot select other channels.

• This equipment has been tested and found to comply within the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

• This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorienting or relocating the receiving antenna – Increasing the separation between the equipment and receiver – Connecting the equipment to an outlet that is on a different circuit from the

radio or TV.

– Consulting the dealer or an experienced radio/TV technician for help.

FCC RADIATION EXPOSURE STATEMENT:

• This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated so there are at least 8 inches (20 cm) between the radiator and your body. This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.

ENGLISH-06

2. IC Notice

• The term “IC” before the radio certication number only signies that Industry Canada technical specications were met. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

• This Class B digital apparatus complies with Canadian ICES-003.

• Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.

• For products available in the US and Canadian markets, only channels 1~11 are available. You cannot select other channels.

IC RADIATION EXPOSURE STATEMENT:

• This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated so there are at least 8inches (20cm) between the radiator and your body. This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.

Open Source License Notice

• This device uses open source software. Open Source Licenses are available on the product menu.

• Tap “Settings > Network > Software Update > Legal Information” on the device for more details.

ENGLISH-07

Safety information

WARNING

f To prevent the risk of electric shock or

re:

– Do not damage the power cord. – Do not pull the power cord too hard or

touch the power plug with wet hands.

– Use only power sources that provide

between 100 and 240 volts. Do not plug the POWERbot into a multi-outlet power strip. Do not place the power cord where it can be stepped on, tripped over, or where the POWERbot can run over it.

– Do not use a damaged power plug, power

cord, or loose power outlet.

f Clean dust or any foreign matter off the

prongs of the power plug.

– There is a risk of electric shock or

malfunction.

WARNING

f Do not use the POWERbot near

combustible materials.

– Do not place or use near candles, desktop

lamps, or replaces or near combustible materials such as gasoline, alcohol, thinners etc.

f The POWERbot is intended for specic

household use. Do not use it in an attic, basement, storage area, industrial building, outside, in places with moisture (such as a bathroom or laundry room), on a table or on shelves.

– The POWERbot can be damaged or

malfunction.

f Be sure the POWERbot does not pass

through or touch any kind of liquid.

– The POWERbot can be severely damaged

and it may contaminate other areas if the wheels pass through liquid.

f Attach the boundary markers to places

where the POWERbot may fall such as the top of a staircase or a bannister to prevent product damage and injury.

– Please keep the cliff sensor clean at all

times for safety.

Power related

Before use

ENGLISH-08

f Do not spill any liquid on the docking

station.

– There is a risk of re or electric shock.

f Do not use the docking station for

anything other than its intended purpose.

– There is a risk of re or severe damage to

the docking station.

f Always keep the cliff sensor clean for

your safety.

WARNING

f If any abnormal sounds, smells, or smoke

come from POWERbot, immediately shut off the POWERBOT using the emergency switch on the bottom of POWERbot, and then contact a Samsung service center.

WARNING

In use

Cleaning and maintenance

f If the power cord is damaged, contact a

Samsuing service center to get it replaced by a certied repairman.

– There is a risk of re or electric shock.

f Contact a Samsung Electronics service

center if you need to replace the batteries.

– Using batteries from other products can

cause the POWERbot to malfunction.

CAUTION

f If a brush or brush cover is not assembled

correctly, scratches may occur on the oor, or product malfunction may occur.

f Before operating the POWERbot, remove

the objects which could break such as a frame, mirror, and porcelain items so that the POWERbot works without interruption.

f Insert the dustbin before using the

POWERbot.

Before use

f For proper automatic recharging, do the

following:

– Always turn on the power of the docking

station.

– Install the docking station where the

POWERbot can nd it easily.

– Do not leave any object in front of the

docking station.

f When installing the docking station, do

not leave the cord on the oor where the POWERbot can run over it.

f Do not use POWERbot on black colored

oors.

– The POWERbot may not be able to operate

normally.

f Do not place any objects within 1.6ft

(0.5m) of either side of the docking station or within 3.3 ft (1m) of the front of the docking station.

f Make sure the docking station's charging

contact is not damaged and is free of foreign matter.

f Do not install the docking station in an

area with a dark oor.

– If the oor around the docking station is

dark, recharging is hindered.

f Move any obstacles that may disturb

POWERbot's movement (such as a children's indoor swing or slide) before cleaning.

f Do not use the POWERbot in a place

which is narrower than its turning radius (1.6 ft/0.5 m or less).

f To clean all areas of your house, open all

rooms and attach the boundary markers to places where the POWERbot could get damaged such as a front door, veranda, bathroom, or stairs.

f For areas with low clearance where

the POWERbot may get stuck, attach the boundary markers to prevent the POWERbot from getting in.

CAUTION

In use

f Using the POWERbot on thick carpet may

damage both the POWERbot and the carpet.

– The POWERbot cannot pass over carpet that

is thicker than 0.4in (1cm).

f Do not use the POWERbot on tables or

other high surfaces.

– There is a risk of damage if it falls.

f The POWERbot may bump into chair or

desk legs. Move them out of the away for faster, more efcient cleaning.

f When the POWERbot is operating, do not

lift it up or carry it to another area.

f Do not hold the POWERbot by its driving

wheels when carrying it to another area.

f Do not put any objects on top of the

POWERbot and camera since this may cause the POWERbot to malfunction.

f Remove any large pieces of paper or

plastic bags from the area to be cleaned before using the POWERbot since they may block the POWERbot's intake.

f Do not aim the red pointer directly at

people or animals.

f Do not lie down near the POWERBOT

when it is running.

– Your hair may be caught in the brush,

resulting in physical injury.

CAUTION

Cleaning and maintenance

f To prevent any damage to the POWERbot:

– Do not clean the POWERbot by spraying

water directly onto it or using benzene, thinner, acetone or alcohol to clean it.

f Do not disassemble or try to repair the

POWERbot yourself. Repairs should only be done by a certied repairman.

f Always keep the obstacle sensor, cliff

sensor, and camera clean.

– If foreign matter accumulates, the sensors

may malfunction.

ENGLISH-09

Installation

The docking station must be plugged in and turned on at all times.

Install the docking station in a place without obstacles and where there is no danger of falling.

About 3.3 ft

About

1.6 ft

(0.5 m)

(1 m)

About

1.6 ft

(0.5 m)

DC-IN

Connect the

battery charger

jack to the docking station

Connect the

power cord

to the battery charger

The side with the sticker attached must face down.

ENGLISH-10

Connect the

power plug to

the outlet

Accessories

Remote control

(Optional)

Docking station Power cord Battery charger Boundary markers

 Accessories may differ depending on the models.  Refer to page 17 for the installation of boundary markers.

Batteries (AAA type)

(Optional)

User manual Spare lter (Optional)

(Optional)

Installation note

Note

f Install the docking station in a place where the oor is level and the wall is straight. f It is best to install the docking station along the grain of wooden oors. f If the emergency switch is off, the POWERbot will not charge even if it is docked in the

docking station.

f Always turn on the power of the docking station.

– If power is not supplied to the docking station, the POWERbot cannot nd it and cannot

automatically recharge.

– If the POWERbot is left detached from the docking station, the battery will drain.

f If the POWERbot is in sleep mode, power will not come on even if the emergency switch is

turned off and then on. Press and hold the [Start/Stop] button on the POWERbot to turn the sleep mode off.

ENGLISH-11

Charging

After completely charging the POWERbot for the rst time (after purchase), it can be used for 60 min. in Nomal ( ) mode. (Refer to the page 41 for the charging time.)

Smart Charging

If the POWERbot's charge runs low while it is in Auto clean mode, it will automatically return to the docking station to recharge, and then will return to the cleaning area after its battery is 2/3rds charged. (Maximum: 2 times.)

• Rated input voltage of

WARNING

this product is 100240V~.

Turn on the

emergency switch

on the bottom

You must turn on the emergency switch to turn on the POWERbot.

Press and release the

button.

Manually charge the POWERbot by

placing it in the docking station

Make sure the charging pins on the POWERbot and the docking station are aligned.

ENGLISH-12

<SR1AM7010U* Series>

<SR1AM7040W* / SR2AM70****

Series>

Check the charging

status

For the SR1AM7010U indicator blinks at 1 second intervals during charging. The indicator will remain on when the battery is fully charged.

For SR1AM7040W* / SR2AM70**** Series, each section of the " " will turn on successively to indicate charging progress and "FULL" will appear when charging is complete.

Series, the battery

Automatic charging

1. SR1AM7010U* Series

If the battery indicator blinks at 0.4 sec. intervals, the POWERbot will automatically return to the docking station to recharge.

2. SR1AM7040W* / SR2AM70**** Series

When the battery indicator blinks during cleaning, the POWERbot will return to the docking station to charge itself automatically.

Recharging

You can command the POWERbot to recharge at the docking station while it is cleaning.

Low battery (Lo)

You can manually charge the POWERbot by placing it in the docking station.

Steps to take if automatic recharging is not occuring:

Reconsider the location of the docking station when:

fthe docking station is located in a place where the POWERbot cannot easily access it.

fthe distance between the docking station and POWERbot is over 16.4ft (5m).

– It may take a long time for the POWERbot to

return to the docking station for recharging

Manually charge the POWERbot when:

fthe docking station is located in a corner fthe battery is fully exhausted fthe POWERbot is immobilized by an obstacle

(furniture, etc.) fthe POWERbot can't climb a threshold near

the docking station (The maximum height of a threshold the POWERbot can climb is about

0.6in (1.5cm)). fthe battery indicator blinks and "Lo" is

displayed fthe battery indicator blinks (Applicable to

SR1AM7010U* Series) fthe POWERbot is set to the Spot clean or

Manual clean mode

ENGLISH-13

Using POWERbot

You must turn on the emergency switch on the bottom of the unit before using POWERbot.

Turning the power on/off

Press the button for more than 3seconds

• When POWERbot is not used for 30 min.;

WARNING

SR1AM70**U* / SR2AM70**U* series: Enters energy-saving mode. SR1AM70**W* / SR2AM70**W* series: Automatically returns to the docking station to

be charged.

Starting Auto clean mode

Press and release this button. The POWERbot moves and automatically cleans the set areas only once.

 Stop cleaning: Press and release the button

Using Spot clean mode

The POWERbot cleans a localized area intensely.

Recharging/Energy-saving mode

fRecharging You can command POWERbot to recharge at the docking station

automatically while it is cleaning by pressing this button. fEnergy-saving mode Refer to page 17.

ENGLISH-14

Selecting cleaning modes

Cleaning mode How to select

Auto clean

Spot clean

Displayed icons

SR1AM7040W*

SR2AM70****

SR1AM7010U*

 Press the [A,B type

Repeat clean

Manual clean

 If POWERbot fails to return to the docking station, it will enter energy-saving mode and the display

panel will be turned off.

 To exit the energy-saving mode, press the [Start/Stop

the remote control.

 If cleaning in Auto clean mode is completed within 15 minutes, POWERbot cleans 1 more time.

[C type ] on the remote controller rst, and then press the [Start/Stop ].

 You can select manual clean

mode using the direction control buttons on the remote control.

] or [Power ] button on the main body or

ENGLISH-15

Using POWERbot

Cleaning method for each mode

About 4.9ft (1.5m)

Auto clean

Automatically cleans the set areas only once.

 SR1AM7010U* series:

Cleans repeatedly until the battery is depleted.

Spot clean

Cleans a localized area intensely. It can be used to clean bread or cookie crumbs.

Manual clean

You can move POWERbot with the remote control to clean the desired spot.

 This function is not

available on the SR1AM7010U* series.

Repeat clean

Cleans repeatedly until the battery is depleted.

 This function is not

available on the SR1AM7010U* series.

Note

f If you select Auto clean or Repeat clean, the POWERbot cleans the area near the docking station rst.

Using special cleaning functions

Cleaning

function

Intelligent

power control

Operation

 When the POWERbot detects a

carpet in normal mode, it will automatically operate with stronger suction power.

SR1AM7040W*

SR2AM70****

Displayed icons

SR1AM7010U*

Edge clean

master

 When the POWERbot detects an

edge or corner in Auto clean or Spot clean, the auto shutter tool operates and approaches the edge or corner section to clean.

fStraight edge (One time cleaning) fCorner (Cleans twice)

ENGLISH-16

About the boundary markers

To prevent the POWERbot from entering the following areas, place the boundary markers on the oor in an shape at intervals of about 5.9in (15cm).

About 5.9in (15cm)

About 1.9in

Boundary

markers

Where a raised spot exceeds 1.9in (5cm) Where there is a slide, swing, replace, or any

Above 0.6in (1.5cm)

boundary

markers

Where a threshold is higher than 0.6in (1.5cm) Where there is risk of falling such as near

(5cm)

ammable substance or moisture.

stairs, porches, or guardrails.

Boundary

markers

About 5.9in (15cm)

Boundary markers

Using Energy-saving mode

You can selectthe Energy-saving modeto save energy during battery charging.Energy-saving mode turns off all functions except battery charging.Use it to reduce powerconsumptionwhile you are away from home for an extended period of time.

How to select or cancel Displayed icon

Press for 5 sec.

 About 3seconds

later, the previous indicator will appear.

Note

f If you select the Auto/Max/Manual clean mode or press the Point cleaning button, the

Energy-saving mode will be cancelled.

f When Energy-saving mode is on, setting the schedule will cancel Energy-saving mode.

– If you select the Energy-saving mode after setting the schedule, the schedule will not be cancelled.

f If the docking station is off, Energy-saving mode will be cancelled. f If the battery is completely at, place the POWERbot on the docking station, and then press

the [Start/Stop

] button on the main body.

ENGLISH-17

<SR1AM7010U* series only>

Blinking Blinking

Using the remote control

[A Type] [B Type]

1 1

3 3

1, 2 1, 2 5 5

[C Type]

4 2 2

Refer to page 23

1, 2 5

Refer to page 23

6 2 4

Refer to page 24

ENGLISH-18

[A Type] / [B Type]/ [C Type]

1 Power / Recharging / Start/Stop

Power

Recharging

Start/Stop

2 Cleaning modes

Auto clean

Spot clean

Repeat clean

3 Suction power

Turbo mode

Turn POWERbot's power on/off

Select to recharge POWERbot at the docking station automatically

Select to start or stop the cleaning process

Select to clean all set areas only once and then have the POWERbot automatically return to the docking station.

Select to clean a localized area intensely

Select to clean repeatedly until the battery becomes very low and the battery level indicator blinks

Select to clean with the strongest suction power

Normal mode

Quiet mode

Select to clean with moderate suction power

Select to clean with lower operational noise

4 Additional function

Each time you press this button, Sound Effects 

Sound

Remote control

 SR1AM7010U5 series only: Star wars (Mute function is not available.)  Turning the emergency switch off and then on will not cancel or change the settings.

Mute is selected in sequence <SR1AM7040W9 series only> Star wars  Sound Effects  Mute

Select to turn the Wi-Fi function on or off

ENGLISH-19

Using the remote control

5 Manual clean mode & Direction control

Move forward

Turn left

Turn right

 Moving backward is not available.

Select to move forward

Select to turn left

Select to turn right

6 Point cleaning

Available only with C type remote controllers.

You can use the remote control to direct the POWERbot to clean a desired spot while the POWERbot is cleaning.

Point the red light on the oor within 1.6ft (0.5m) of the POWERbot's location.

Press and hold the Point cleaning button to move the red light to the desired spot. The POWERbot will follow the light while cleaning.

1.6ft (0.5m)

Operating distance of the remote control

Height of the

remote control

Operating

distance

Height of the remote control

Operating distance

Inserting batteries

Open the battery cover by lifting it up while pressing the locking tab. Insert the batteries as shown in the illustration, and then close the cover until it clicks into place.

ENGLISH-20

1.6ft (0.5m) 3.3ft (1m) 4.9ft (1.5m)

About 4.9ft

(1.5m)

About 6.6ft

(2m)

About 9.8ft

(3m)

Name of each part

Top

1. Display panel

2. Remote control signal receiver

3. Obstacle sensor

4. Dustbin

5. Camera

6. Dustbin button

7. Bumper sensor

8. Auto shutter tool

Bottom

1. Charging pins

2. Brush

3. Brush cover

4. Cliff sensor

5. Roller

6. Battery cover

7. Brush cover button

8. Driving wheel

9. Emergency switch

10. Auto shutter tool

ENGLISH-21

Name of each part

12 138 11109

Display panel

<SR1AM7010U* series>

1. Daily schedule

2. Normal/Turbo mode

3. Battery indicator

4. Spot cleaning button, dailyschedule(3sec)

5. Start/Stop button, Turbomode(3sec)

6. Recharging button

<SR1AM7040W* / SR2AM70**** series>

1. Mute

2. Information Indicator

3. *Smart Control Off/On indicator

4. *Wi-Fi

5. Battery indicator

6. One-time/Daily schedule

7. Number display

8. Spot clean mode

9. Manual clean mode

10. Repeat clean mode

11. Quiet mode

12. Normal mode

13. Turbo mode

14. Spot cleaning button

15. Start/Stop button

16. Recharging button

 SR1AM70**W* / SR2AM70**W* : Wi-Fi supported model

ENGLISH-22

Setting time/schedule

[A Type, B Type] Only Auto clean mode can be scheduled.

Setting the time

You must set the current time before using the One-time/daily schedule function.

Start setting Select "Hour" Select "Minute"

Select "AM/PM"Setting complete

Skip to previous, next setting

Setting the schedule

You can set/cancel the schedule only when the POWERbot is docked in the docking station.

Start setting Select "One-time" or

"Daily" schedule

Cancelling during setup

fThe setting will be canceled automatically if there's no input for 7seconds.

Cancelling One-time/Daily schedule

When both One-time/ Daily schedule is set

Press for 3 sec. Select the schedule Cancel complete

When either one of One-time or Daily schedule is set

Select "Hour"

Press for 3 sec.

Select "Minute"Select "AM/PM"Setting complete

Skip to previous, next setting

ENGLISH-23

Setting time/schedule

[C Type] Only Auto clean mode can be scheduled.

Setting the time

You must set the current time before using the One-time/daily schedule function.

Start setting Select "Hour" Select "Minute"

Select "AM/PM"Setting complete

Skip to previous, next setting

Setting the schedule

You can set/cancel the schedule only when the POWERbot is docked in the docking station.

Start setting Select "One-time" or

"Daily" schedule

Cancelling during setup

fThe setting will be canceled automatically if there's no input for 7seconds.

Cancelling One-time/Daily schedule

When both One-time/ Daily schedule is set

Press for 3 sec. Select the schedule Cancel complete

When either one of One-time or Daily schedule is set

Select "Hour"

Select "Minute"Select "AM/PM"Setting complete

Skip to previous, next setting

or or

Press for 3 sec.

ENGLISH-24

[SR1AM7010U* series] For the models which do not include a remote control, you can set a daily schedule as described below.

Setting the schedule

You can set/cancel the schedule only when the POWERbot is docked in the docking station.

Press for 3 seconds.

 The time you pressed the button will be set as the time that the POWERbot is scheduled to begin

cleaning. The POWERbot will automatically begin cleaning every day at that scheduled time.

When the schedule LED is turned

on, the daily schedule is set.

Cancelling daily schedule

When a daily schedule is set

Press for 3 seconds.

ENGLISH-25

Cleaning and maintaining

You must turn off the emergency switch before cleaning the POWERbot.

Cleaning the dustbin

Press the button to

remove the dustbin

Detach the cyclone

unit from the dustbin cover, and then wash the dustbin and the lter

Remove the dustbin

cover

Reassemble the

dustbin

Cleaning the sensors and the camera

Remove dust in the

dustbin and cyclone unit

'Click'

Reinsert the dustbin

into the main body until it clicks

Lightly wipe with a soft cloth. Do not use water or cleaning solutions.

Camera

Front sensor

window

ENGLISH-26

Cliff sensors

Rear sensor

window

Cleaning the brush and Auto shutter tool

Brush design may differ depending on the model.

Remove the

brush cover

Reassemble the brush

Remove the

brush

Cleaning the Driving wheel

Clean the

brush

Reassemble the brush cover

Clean the auto

shutter tool

Put a soft cloth on the oor and place

POWERbot upside-down on the cloth.

ENGLISH-27

Use a blunt rod or tweezers to remove foreign matter.

SmartThings App

The SmartThings App is only compatible with models that have a Wi-Fi function.

Setting up the wireless router

f Please refer to the user manual of your wireless router if you have access problems. f Samsung POWERbot supports only Wi-Fi 2.4 Ghz. f Samsung POWERbot supports IEEE 802.11b/g/n and Soft-AP.

– IEEE 802.11n is recommened.

f Samsung POWERbot supports only DHCP (Dynamic Host Conguration Protocol). Please

make sure that the DHCP server option is activated on your wireless router.

f POWERbot supports the WEP-OPEN, WPA-PSK/TKIP, and WPA2-PSK/AES for the

authentication and encryption protocols.

– WPA2-PSK/AES is recommended. – Conrm that your router has a unique SSID and password.

f The quality of your wireless network connection may be inuenced by the surrounding

wireless environment.

f If your Internet service provider has permanently registered the MAC address (a unique

identication number) of your PC or modem, your POWERbot may not be able to connect to the Internet. Ask your Internet service provider about the procedure to connect an apparatus other than a PC to the Internet.

f If your internet service provider requires your ID or password to connect to the internet,

your POWERbot may not be able to connect. If this is the case, you must enter your ID or password when connecting to the Internet.

f The POWERbot may not be able to connect to the Internet because of rewall issues.

Contact your Internet service provider to resolve these issues.

f Some wireless routers may transmit an abnormal Domain Name Server (DNS) address even

if the Internet is not connected. If this occurs, contact the manufacturer of your wireless router and your Internet service provider.

f If you still cannot connect to the Internet even after trying the procedure provided by your

Internet service provider, please contact an authorized Samsung service center.

f If your router is not a Wi-Fi certied product, The POWERbot may not be able to connect to

the Internet.

ENGLISH-28

Downloading the SmartThings App

f Download and install the SmartThings app from the markets (Google Play Store, Apple App

Store, or Samsung Galaxy Apps). To nd the app, use the keyword “SmartThings”.

Note

f SmartThings is incompatible with tablets and some mobile devices.

– Android 6.0 or later (at least 2GB of RAM) is recommended.

f iPad and some mobile devices may not be supported.

– iOS 10.0 or later / iPhone 6 or later is supported.

f Visit Play Store or App Store to see if your mobile device is compatible with SmartThings. f The supported features are subject to change without any prior notice.

Setting up a Samsung account

f You must sign in to a Samsung account before using the SmartThings app. f To set up a Samsung account, you can follow the directions provided by the SmartThings

app.

f Or, if you have a Samsung smartphone, you can add your Samsung account in the setting

app of your smartphone. Then, it will automatically sign in to your Samsung account.

ENGLISH-29

SmartThings App

Adding a device to the SmartThings APP

1. Connect your smartphone to your wireless router.

2. Launch the SmartThings app on your smartphone.

3. If a pop-up saying that a new device has been found appears, tap ADD NOW. – If the pop-up doesn’t appear, tap the + button and select the device which you want to connect

from the list of AVAILABLE DEVICES.

– If your device doesn’t appear in the list, add the device manually by selecting the device type and

selecting the specic device model.

4. [Android] The connection to your device will be progressed automatically. – [iOS] Open the setting app, and select [robot vacuum] Samsung in the Wi-Fi list.

5. Provide the authentication when you are directed to do so.

6. [Android] The connetion to your wireless router will be progressed automatically. – [iOS] Open the setting app, and select the wireless router in the Wi-Fi list.

7. The remaining setup will be automatically done. Then, a new Device Card will be added.

Note

f If you cannot complete the product registration, please take the following steps.

– Try the registration procedure again as you have directed by the pop-up messages. – Conrm that the UPnP option of your wireless router is active, and then try the registration

procedure again.

– Conrm that your wireless router is operating in wireless mode, and then try the registration

procedure again.

– If you have two or more POWERbots, turn off the other POWERbots, and then try to register your

POWERbot again.

– If there is any other wireless router that has the same SSID as your wireless router, the

registration might be failed.

f Smart control and Wi-Fi indicator

Smart control is blocked. (The remote controller can still

be allowed.)

Off Smart control is allowed.

On The POWERbot is connected to the wireless router.

Off The POWERbot is trying to connect the wireless router.

f When the Smart control is blocked, you cannot control the POWERbot on your smartphone. f The POWERbot and your smartphone are not connected to the same wireless router, a

response delay may occur depending on your network environment.

ENGLISH-30

+ 98 hidden pages