Samsung VR2AJ9040WG/AA, VR2AJ9020UG/AA, VR2AJ9010UG/AA User Manual
POWERbot
user manual
SR2AJ90U Series
SR2AJ90W Series
Before operating this unit, please read the instructions carefully.
For indoor use only.
imagine the possibilities
Thank you for purchasing a Samsung product.
English
Contents
Safety information
03
Installation
10
Accessories
Charging
12
Automatic charging / Recharging / Low
battery
Using POWERbot
14
Selecting cleaning modes / Using Energysaving mode
Using the remote control
17
Name of each part
19
Top / Bottom / Display panel
Cleaning and maintaining
21
Cleaning the dustbin / Cleaning the sensors and
the camera / Cleaning the Pet brush / Cleaning
the Driving wheel
Setting time/schedule
23
Setting the time / Setting the schedule
24
32
34
36
38
39
ENGLISH-02
Samsung Smart Home App
Preparing the network / Using the Samsung
Smart Home app
Notes and cautions
Charging / In use / Cleaning and maintenance /
About battery
Information codes
Troubleshooting
Open Source Announcement
Specifications
Safety information
SAFETY INFORMATION
• Before operating the appliance, please read this manual thoroughly and retain it
WARNING
WARNING
CAUTION/WARNING SYMBOLS USED
for your reference.
• Because these following operating instructions cover various models, the
characteristics of your vacuum cleaner may differ slightly from those described in
this manual.
WARNING
CAUTION
Indicates that a danger of death or serious injury exists.
Indicates that a risk of personal injury or material damage exists.
OTHER SYMBOLS USED
NOTE
Indicates that a risk of personal injury or material damage exists.
This Smart Robot vacuum supports from Samsung Smart Home.
More detailed information, please visit Samsung.com/Smarthome.
State of California Proposition 65 Warning (US only)
This product contains chemicals known to the State of California to cause
WARNING
cancer and birth defects or other reproductive harm.
L i - i o n
For battery recycling go to call2recycle.org;
or call 1-800-822-8837
ENGLISH-03
Safety information
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should be observed, including the
following:
READ ALL INSTRUCTIONS BEFORE USING YOUR POWERbot.
Unplug from outlet when not in use and before conducting maintenance.
WARNING: to reduce the risk of fire, electric shock, or injury:
GENERAL
•Use only as described in this manual.
•Do not operate POWERbot or the adapter / docking station if it has been damaged in
any way.
•If the vacuum cleaner is not working as it should, has been dropped, damaged, left
outdoors, or dropped in water, return it to a customer care center.
•Do not handle the adapter / docking station or POWERbot with wet hands.
•Use only on dry, indoor surfaces.
•This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge
if they have been given supervision or instruction concerning use of the appliance in a
safe way and understand the hazards involved.
•Children shall not play with the appliance. Cleaning and user maintenance shall not be
made by children without supervision.
Adapter / Docking station
•Do not modify the polarized plug to fit a non-polarized outlet or extension cord.
•Do not use outdoors or on wet surfaces.
•Unplug the adapter / docking station from the outlet when not in use and before
servicing.
•Use only the adapter / docking station supplied by the manufacturer to recharge.
•Do not use with a damaged cord or plug or a loose power outlet.
•Do not pull or carry by the cord, use the cord as a handle, close the door on the cord,
or pull the cord around sharp edges or corners. Keep the cord away from heated
surfaces.
•Do not use extension cords or outlets with inadequate current carrying capacity.
•Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
•Do not mutilate or incinerate batteries as they will explode at high temperatures.
•Do not attempt to open the adapter / docking station. Repairs should only be carried
out by a qualified customer care center.
ENGLISH-04
•Do not expose the adapter / docking station to high temperatures or allow moisture or
humidity of any kind to come into contact with the adapter / docking station.
POWERbot
•Do not pick up hard or sharp objects such as glass, nails, screws, coins, and etc.
•Do not use without a filter in place. When servicing the unit, never put fingers or other
objects into the fan chamber in case the unit accidentally turns on.
•Do not put any objects into openings. Do not use with any openings blocked; keep
openings free of dust, lint, hair, and anything that may reduce air flow.
•Do not pick up toxic materials (chlorine bleach, ammonia, drain cleaner, etc.).
•Do not pick up anything that is burning or smoke, such as cigarettes, matches, or hot
ashes.
•Do not use to pick up flammable or combustible liquids such as gasoline, nor use on
areas where they may be present.
•Locations with candles or desk lamps on the floor.
•Locations with unattended fires (fire or embers).
•Locations with distilled alcohol, thinner, ashtrays with burning cigarettes, etc.
•Do not use POWERbot in an enclosed space filled with vapours given off by oil based
paint, paint thinner, moth proofing substances, flammable dust, or other explosive or
toxic vapours.
•Leaks from battery cells can occur under extreme usage or temperature conditions.
If the liquid gets on skin, wash quickly with water. If the liquid gets into the eyes,
flush them immediately with clean water for a minimum of 10 minutes. Seek medical
attention.
SAVE THESE INSTRUCTIONS
POLARIZED PLUG INSTRUCTIONS
•To reduce the risk of electric shock, this appliance has a polarized plug (one blade is
wider than the other). This plug will fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install a proper outlet. Do not modify the plug in any way.
ENGLISH-05
Safety information
REGULATORY NOTICE
1. FCC Notice
CAUTION
FCC CAUTION:
•Any changes or modifi cations not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
•This device complies with Part 15 of FCC Rules. Operation is Subject to following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received including interference that
cause undesired operation.
•For product available in the USA/Canada market, only channel 1 ~ 11 can be operated.
Selection of other channels is not possible.
FCC STATEMENT:
•This equipment has been tested and found to comply within the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
•This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna
– Increase the separation between the equipment and receiver
– Connect the equipment into an outlet on a diff erent circuit from that to which the
receiver is connected
– Consult the dealer or an experienced radio/TV technician for help.
FCC RADIATION EXPOSURE STATEMENT:
•This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance
of 20cm between the radiator and your body. This device and its antenna(s) must not
be co-located or operation in conjunction with any other antenna or transmitter.
ENGLISH-06
2. IC Notice
•The term “IC” before the radio certifi cation number only signifi es that Industry Canada
technical specifi cations were met. Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
•This Class B digital apparatus complies with Canadian ICES-003.
•Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.
•For product available in the USA/Canada market, only channel 1 ~ 11 can be operated.
Selection of other channels is not possible.
IC RADIATION EXPOSURE STATEMENT:
•This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body. This device and its
antenna(s) must not be co-located or operation in conjunction with any other antenna or
transmitter.
Open Source License Notice
•This device uses open source software. Open Source Licenses are available on the
product menu.
•Tap “Settings > Network > Software Update > Legal Information” on the device for more
details.
ENGLISH-07
Safety information
WARNING
f Please prevent any risk of electric shock or
fire.
– Do not damage the power cord.
– Do not pull the power cord too hard or touch
the power plug with wet hands.
– Do not use a power source other than 100-
240 V~ and also do not use a multi outlet to
supply power to number of devices at the same
time. (Do not leave the cord carelessly on the
floor.)
– Do not use a damaged power plug, power cord
or loose power outlet.
f Clean dust or any foreign matters on the pin
and contact part of the power plug.
– There is a risk of electric shock or malfunction.
WARNING
f Do not use POWERbot near combustible
materials.
– Place near candle, desktop lamps, fireplace or
near combustible materials such as gasoline,
alcohol, thinners etc.
f The POWERbot is intended for household
use therefore do not use it in an attic,
basement, storage, industrial building, out of
indoor space, places with moisture (such as
bathroom, laundry), on the table or shelves.
– The POWERbot can be damaged or
malfunction.
f Be sure POWERbot does not pass through or
touch any kind of liquids.
– The POWERbot can be severely damaged and
it may contaminate other areas if the wheels
pass through liquid.
f Do not spill any liquids on the docking station.
– There is a risk of fire or electric shock.
Power related
Before use
f Do not use the docking station for anything
other than its intended purpose.
– There is a risk of fire or severe damage to the
docking station.
f Always keep the cliff sensor clean for your
safety.
WARNING
f If any abnormal sounds, smells or smoke
come from POWERbot, immediately shut
off the emergency switch at the bottom of
POWERbot and contact a service center.
WARNING
In use
Cleaning and
maintenance
f When power cord is damaged, contact a
service center to get it replaced by certified
repairman.
– There is a risk of fire or electric shock.
f Please check with a Samsung Electronics
service center when exchanging batteries.
– Using batteries from other products can cause
malfunction.
ENGLISH-08
CAUTION
Before use
CAUTION
In use
f Insert the dustbin before using POWERbot.
f Be careful with the followings for proper
automatic recharging.
– Always turn on the power of the docking
station.
– Install the docking station where POWERbot
can easily find.
– Do not leave any object in front of the docking
station.
f When installing the docking station, do not
leave the cord carelessly on the floor since
POWERbot may get tangled by it.
f Do not use POWERbot on black colored
floors.
– The POWERbot may not be able to operate
normally.
f Do not pick up POWERbot by the dustbin
holder.
f Do not place any objects within 0.5 m to both
sides and 1 m to the front of the docking
station.
f Make sure the docking station's charging
contact is not damaged or have any foreign
matters on it.
f Do not install the docking station in an area
with a dark floor.
– If the floor around the docking station is dark,
recharging is hindered.
f Move any obstacles that may disturb
POWERbot's movement (such as children's
indoor swing or slides) before cleaning.
f Using POWERbot on thick carpet may
damage both POWERbot and the carpet.
– The POWERbot cannot pass over carpet that is
thicker than 1 cm.
f Do not use POWERbot on tables or other
high surfaces.
– There is a risk of damage if it falls.
f The POWERbot may bump into chair, desk
legs therefore move them away for faster and
efficient cleaning.
f When POWERbot is operating, do not lift it up
or carry it to another area.
f Do not hold by driving wheels of POWERbot
when carrying it to another area.
f Do not put any objects on top of POWERbot
since it may cause malfunction.
f Remove any large papers or plastic bags
immediately when using POWERbot since
they may block the intake.
f Do not aim the red pointer directly at people
or animals.
CAUTION
Cleaning and
maintenance
f Prevent any damage to POWERbot by
complying the followings.
– Do not clean POWERbot by spraying water
directly onto it or use benzene, thinner, acetone
or alcohol to clean it.
f Do not disassemble or repair POWERbot.
This should only be done by a certified
repairman.
f Always keep the obstacle sensor and cliff
sensor clean.
– If foreign matter accumulates, sensors may
malfunction.
ENGLISH-09
Installation
The docking station must be plugged in and turned on at all times.
Install the docking station in a place
without obstacles and danger of
falling.
Power lamp (Red)
About 1 m
About 0.5 m
DC-IN
About 0.5 m
DC-IN
Connect the
adapter jack
1
to the docking
station
Connect the
power cord to
2
the adapter
When using the adapter,
the side with the sticker
attached must face down.
ENGLISH-10
Connect the
power plug to
3
the outlet
The power indicator lamp
(Red) will turn on.
Accessories
Remote control Batteries (AAA type) User manual Spare filter (Option)
Cleaning brush Power cord Adapter
Note
f Install the docking station in a place where the floor and wall are level.
f It is best to install the docking station along the grain of wooden floors.
f If the emergency switch is off, the POWERbot will not charge even if it is docked on the docking
station.
f Always turn on the power of the docking station.
– If power is not supplied to the docking station, the POWERbot cannot find it and cannot automatically
recharge.
– If the POWERbot is left detached from the docking station, the battery will drain naturally.
f If the POWERbot is in sleep mode, power will not come on even if the emergency switch is turned
off and then on. Press and hold the [Start/Stop] button on the POWERbot to turn off the sleep
mode.
ENGLISH-11
Charging
It takes approximately 160 minutes to
completely charge the POWERbot when
charging it for the first time after purchase.
Once charged, the POWERbot can be used
for approximately 60 minutes.
Charging light turns green during charging.
WARNING
• Rated input voltage of this product
is 100-240 V~.
Turn on the
emergency
1
switch on the
bottom
You must turn on the
emergency switch to turn on
the POWERbot.
Manually charge
the POWERbot by
2
placing it on the
docking station
Make sure the charging pins
on the POWERbot and the
docking station are aligned.
ENGLISH-12
<SR2AJ90U Series>
<SR2AJ90W Series>
Check the charging
status
3
For SR2AJ90U Series,
“ ”appears in
the sequence to show charging
progress. All the icons appear when
charging is complete.
For SR2AJ90
" " will turn on according to
charging progress and "FULL" will
turn on when charging is complete.
W Series,
Automatic charging
When the battery indicator blinks
during cleaning, the POWERbot
will return to the docking station to
charge itself automatically.
Recharging
You can command the POWERbot
to recharge at the docking station
while it is in cleaning.
Low battery
Manually charge the POWERbot by
placing it on the docking station.
Steps to take if recharging not occuring:
Check the installation status of the
docking station when:
fthe docking station is located in a place where the
POWERbot cannot easily access it.
fthe distance between the docking station and
POWERbot is over 16.5 ft (5 m).
– It may take a long time for POWERbot to
return to the docking station for recharging
ENGLISH-13
Manually charge the POWERbot when:
fthe docking station is located in a corner
fthe battery is fully exhausted
fthe POWERbot is immobilized by an obstacle
(furniture etc.)
fthe POWERbot can't climb a threshold near the
docking station (The maximum height of a threshold
the POWERbot can climb is about 0.6 inches
(1.5 cm).)
fthe battery indicator blinks
fthe POWERbot is set to the Spot clean or Manual
clean mode
Using POWERbot
You must turn on the emergency switch on the bottom of the unit before using POWERbot.
Turning the power on/off
Press the button for more than
3 seconds
• When POWERbot is not used for
WARNING
60 minutes, power will turn off
automatically.
Starting Auto clean mode
Press and release this button. Cleans space
dividing until the battery is depleted .
Stop cleaning: Press and release the button
Starting Spot clean mode
Press and release this button. The POWERbot
cleans a localized area intensely.
Recharging
fRecharging
You can command POWERbot to recharge at the
docking station automatically while it is cleaning
by pressing this button.
ENGLISH-14
Selecting cleaning modes
Displayed icon
Cleaning mode How to select
SR2AJ90U
Series
Auto clean
Spot clean
The movement and
Manual clean
When the POWERbot is being charged, you can select the Auto clean mode
only.
If the POWERbot fails to return to the charger, it will be turned into the sleep
mode. Then the display panel of the main body will be turned off. Press
[Start/Stop] or [Power] button to cancel the sleep mode.
Charging and cleaning times may differ according to conditions of use.
direction of the POWERbot
is controlled by the remote
control.
<Displayed icons in the sleep mode>
SR2AJ90W
Series
Cleaning method for each modes
About 59 inches (1.5 m)
About 59 inches (1.5 m)
Auto clean
Cleans space dividing until the
battery is depleted .
Spot clean
Cleans a localized area intensely.
It can be used to clean bread or
cookie crumbs.
ENGLISH-15
Manual clean
You can control the POWERbot
with the remote control and direct it
to clean a desired spot.
Using POWERbot
Using Energy-saving mode
You may select the Energy-saving mode to save energy during battery charging. Energy-saving mode turns off
all functions except battery charging. It reduces the power consumption while you are away from home for an
extended period of time.
Displayed icon
How to select or cancel
Press for 5 sec.
When the POWERbot is in the Energy-saving mode, the green lamp of the docking station will blink.
SR2AJ90U
Series
About 3 seconds later, the previous
indicator will appear.
SR2AJ90W
Series
Note
f If you select the Auto/Max/Manual clean mode or press Point cleaning button, the Energy-saving
mode will be cancelled.
f During the Energy-saving mode, setting the schedule will cancel the Energy-saving mode.
– If you select the Energy-saving mode after setting the schedule, the schedule will not be cancelled.
f If the power of the docking station is off, the Energy-saving mode will be cancelled.
ENGLISH-16
Using the remote control
1 Power/Recharging
[A Type] [B Type]
Power
Recharging
Start/Stop
2 Cleaning modes
Auto clean
Spot clean
3 Suction modes
Silence mode
Turn POWERbot's power on/off
Select to recharge POWERbot at the docking station
while it is cleaning.
Select to start or stop cleaning
Cleans space dividing until the battery is depleted.
Select to clean a localized area intensely
Select to clean with lower operational noise
Normal mode
4 Additional functions
Sound
Smart control
-
Select to clean with normal suction power
Each time you press this button, Sound Effects
Mute is selected in this sequence.
Select to turn on or off the smart control
Wi-Fi connection should be done to control the
POWERbot using Samsung Smart Home app.
ENGLISH-17
Using the remote control
[A Type]
5 Direction control
[A Type] [B Type]
Select to move forward
1
2
1
5
Moving backward is not available
4
3
Inserting batteries
Open the battery cover by lifting it up while pressing the locking tab,
and then insert the batteries as shown in the illustration. Then, close
the cover until it clicks into place.
Select to turn left
Select to turn right
[B Type]
1
2
1
5
4
3
Refer to page 23
ENGLISH-18
Name of each part
1
2
3
3
5
6
7
Top
1. Display panel
2. Dustbin holder
3. Remote control signal receiver
4. Obstacle sensor
5. Dustbin
6. Camera
7. Dustbin handle
4
1
2
3
4
5
3
8. Bumper sensor
8
4
Bottom
1. Charge pins
2. Pet brush
7
3. Pet brush cover
4. Cliff sensor
4
5. Roller
8
6. Battery cover
7. Pet brush cover button
6
5
8. Driving wheel
9
9. Emergency switch
ENGLISH-19
12
10
1
2
6
Display panel
1
2
8 94 765
8 11109
14
13
12
11
3
<SR2AJ90U Series>
1. Mute
2. Information indicator
3. Battery indicator
4. Auto clean
5. Spot clean
6. Manual clean
7. Silence mode
8. Normal mode
9. Recharging
10. Spot cleaning button
11. Start/Stop button
12. Recharging button
3
4
<SR2AJ90W Series>
1. Mute
5
7
2. Information indicator
3. Smart Control
4. Wi-Fi indicator
5. Battery indicator
6. One-time/Daily schedule
7. Number display
8. Spot clean
9. Manual clean
10. Silence mode
11. Normal mode
12. Spot cleaning button
13. Start/Stop button
14. Recharging button
ENGLISH-20
Cleaning and maintaining
You must turn off the emergency switch before cleaning POWERbot.
Cleaning the dustbin
Remove the dustbin
1
Detach the cyclone unit
4
from the dustbin cover,
and then wash the
dustbin and the filter
Remove the dustbin
2
cover
Reassemble the
5
dustbin
Cleaning the sensors and the camera
Remove dust in the
3
dustbin and cyclone
unit
"Click"
Reinsert the dustbin
6
into the main body until
it clicks
Lightly wipe with soft cloth. Do not use water or cleaning solutions.
Camera
Front sensor
window
ENGLISH-21
Cliff sensors
Rear sensor
window
Cleaning the Pet brush
ON
OFF
Remove the Pet brush
1
Remove the Pet brush
2
cover
OFF
ON
Reassemble the Pet
4
brush
Reassemble the Pet
5
brush cover
Cleaning the Driving wheel
Clean the Pet brush
3
Put a soft cloth on the floor and place
1
POWERbot upside-down on the cloth.
Use a blunt rod or tweezers to remove foreign
2
matter.
ENGLISH-22
Setting time/schedule
This function is only available for SR2AJ90W Series.
Setting the time
You must set the current time before using the One-time/daily schedule.
Start setting Select "Hour" Select "Minute"
or
Select "AM/PM"Setting complete
Skip to previous, next setting
Setting the schedule
Setting/cancelling the schedule can only be done while POWERbot is docked on the charger.
Start setting
Setting complete
Select "One-time" or
"Daily" schedule
or
Cancelling
during setup
Select "AM/PM"
fSetting will be canceled automatically when there's no input
for 1 minute.
Select "Hour"
Select "Minute"
Skip to previous, next setting
Cancelling One-time/Daily schedule
When both One-time/
Daily schedule is set
Press for 3 sec. Select the schedule Cancel complete
When either one of
One-time or Daily
schedule is set
Press for 3 sec.
ENGLISH-23
Samsung Smart Home App
This function is only available for SR2AJ90W Series.
Preparing the network
Setting up the wireless router
fThis product supports only DHCP(Dynamic Host Configuration Protocol). Please check if the DHCP server
option function of a wireless router is activated.
fThe supported types of authorization/encryption of the wireless router are WEP-OPEN, WPA-PSK/TKIP and
WPA2-PSK/AES 801.11n.
– WPA2-PSK/AES is recommended to be used.
fThe quality of connection of the wireless network may be influenced by the surrounding wireless environment.
fWhen your Internet service provider has permanently registered an MAC address (a unique identification
number) of your PC or modem, your POWERbot may be unavailable to be connected to the Internet. Ask your
Internet service provider about the procedure to connect an apparatus other than a PC to the Internet.
fIf your internet service provider requires your ID or password to connect to the internet, your POWERbot may
not be able to connect to the internet. In this case, you must enter your ID or password when connecting to
the internet.
fThe connection to the Internet may be impossible because of issues of firewall. Ask your Internet service
provider for resolving the issue.
fSome wireless routers may convey an abnormal Domain Name Server (DNS) address even if the Internet is not
connected. In this case, inquire the provider of the pertinent wireless router and your Internet service provider.
fIf you still cannot connect to the Internet even after trying the procedure informed by your Internet service
provider, please ask an agency or service center of Samsung Electronics.
Note
f Please refer to the user manual of the pertinent wireless router with access problems.
f Samsung POWERbots support only Wi-Fi 2.4 Ghz.
f Samsung POWERbots support the communication protocol of the methods of IEEE 802.11b/g/n
and Wi-Fi Direct. (Samsung Electronics recommends to use IEEE 802.11n.)
f A wireless router with no authorization of Wi-Fi may be unavailable to be connected to the
POWERbot.
f When the power is supplied and the POWERbot is docked on the charger, the POWERbot will be
connected to the server and then check if there is software updates. If there is the latest software, it
will be automatically downloaded and updated.
ENGLISH-24
f If “UP” is displayed on the display panel while the POWERbot is charging, it means that the update
is in progress. Please wait for completing the rebooting.
f If the product registration is not done, please follow the following instructions:
– Refer to the popup message and retry the registraion procedure.
– Check if the UPnP option of the wireless router is available and retry the registration procedure.
– Check if the operating mode of the wireless router is a router mode and retry the registration procedure.
– If you have more than two POWERbot, turn off the others to register the one. The connection must be one
to one.
f Samsung Smart Home Service does not guarantee a normal operation under firewall environment.
f If the POWERbot and smart phone are not connected to the same wireless router, response delay
may occur according to network environment.
f Smart control and Wi-Fi indicator
– On : Smart control is locked.
–
Off : Smart control is allowed.
–
Off : The POWERbot is connecting to the wireless router.
–
On : The POWERbot is connected to the wireless router.
f If Smart control is locked, you cannot use Samsung Smart Home App.
Using the Samsung Smart Home app
Creating your Samsung account
If you want to use the Samsung Smart Home app, please register your
Samsung account in Samsung account app.
Note
f If you do not set auto-login to the Samsung Smart Home app and run
the app, the screen of Samsung account appears one time at first.
f If you are a user of a Samsung smart phone, register your Samsung
account in the settings of the smart phone, and then the automatic
login gets set without any other login processes, and you can use the
Samsung smart home app immediately.
ENGLISH-25
Samsung Smart Home App
Downloading Samsung Smart Home app
You can download the Samsung Smart Home app by searching for “Samsung Smart Home App” at the Google
Play Store, Samsung Galaxy Apps and Apple App store.
Note
f Samsung Smart Home apps are compatible with selected Samsung Galaxy S and Samsung Note
series devices.
– support Android™(2) 4.0 (since Galaxy S2) or higher and iOS7 or higher
– Application must be downloaded. Internet connection required. Data changes may apply.
– Android is a trademark of Google Inc
– The UI of Samsung Smart Home App may change without advance notice for improvement of product use
and performance.
Registering the product (Easy-Setup)
Register the product to the Samsung Smart Home Service before using the Samsung Smart Home app.
Android
1. Press the Add new icon on the device list screen of the Samsung Smart Home app to start the registration of the
product.
2. Select the Robot vacuum icon.
3. Enter the information of the wireless router to be connected.
4. Set the POWERbot according to the guidance on the screen.
– To turn on the AP mode immediately, press [Clock] button for more than 5 seconds.
ENGLISH-26
5. Then, the registration will proceed automatically.
6. The message will appear when the registration complete.
7. When the product registration is complete, the main screen of the Samsung Smart Home app will appear.
If the product registration is failed, refer to page 24. Samsung Smart Home App
ENGLISH-27
Samsung Smart Home App
iOS
1. Run Samsung Smart Home app..
2. Move to the left screen and then press the Add new icon on the device list screen to start the registration of the
product.
3. Enter the samsung account and then press [Sign in] button.
– For iPhone, your ID and password is not saved so that you need to sign in everytime you use Samsung
Smart Home app.
4. Select [Robot vacuum] icon.
5. Press the clock button of the remote controller for more than 5 seconds.
– AP will appear on the display panel.
ENGLISH-28
6. Run the Settings app of your iPhone and then connect to [Robot Vacuum] Samsung on the list.
7. Enter ID and password of the wireless router which will be connected and then press [Next] button.
8. The connection beween the mobile and the robot vacuum is in progress.
9. Run the Settings app of your iPhone and then connect to the wireless router which will be connected on the WiFi list.
10. The connection beween the wireless router and the robot vacuum is in progress.
11. When the product registration is completed, the message will appear.
12. When the product registration is completed, Robot vacuum icon is added on the device list.
ENGLISH-29
Samsung Smart Home App
Main screen
fSelect the Robot vacuum icon on the main screen, and you can move to the
POWERbot control screen.
fYou can control your smart home appliances made by Samsung Electronics
by Going out, Coming home, Good night, and Good morning icons.
fHome view function is not supported for a POWERbot.
User menu screen
fYou can control the smart home appliances made by Samsung Electronics
with Chat control and Master key functions.
Chat control
Master key
Customer service
fYou can control the smart home appliances or check about the
status of them conveniently.
fYou can control several home appliances at once using the
master keys(Going out, Coming home, Good night, Good
morning).
fYou can see the manual of the product.
fWhen a product is out of order, you can consult with our
customer center and request for an after-sales service.
ENGLISH-30
Loading...