How it Works
Samsung
Loading...
VR1AM7010U5
User Manual
128 pgs42.01 Mb0

Samsung VR1AM7010U5 User Manual

POWERbot
User manual
SR1AM70
• Before operating this unit, please read the instructions carefully.
• For indoor use only.

, SR2AM70

Series
Contents
Safety information
03
Installation
10
Accessories / Installation note
Charging
12
Automatic charging / Recharging / Low battery (Lo)
Using POWERbot
14
Turning the power on/off / Selecting cleaning modes/ Using special cleaning functions/ About the boundary markers/ Using Energy-saving mode
Using the remote control
18
Name of each part
21
Top / Bottom / Display panel
Setting time/schedule
23
Setting the time / Setting the schedule
Cleaning and maintaining
26
Cleaning the dustbin / Cleaning the sensors and the camera / Cleaning the brush and Auto shutter tool / Cleaning the Driving wheel
Samsung Connect App
28
Notes and cautions
32
Charging / Using / Cleaning and maintenance / About the battery / About the IrDA sensor
Information codes
34
Troubleshooting
36
Open Source Announcement
40
Specications
41
ENGLISH-02
Safety information
SAFETY INFORMATION
• Before operating the appliance, please read this manual thoroughly and
WARNING
WARNING
CAUTION/WARNING SYMBOLS USED
retain it for your reference.
• Because the following operating instructions cover various models, the
characteristics of your vacuum cleaner may differ slightly from those described in this manual.
WARNING
CAUTION
Indicates that a danger of death or serious injury exists.
Indicates that a risk of personal injury or material damage exists.
OTHER SYMBOLS USED
Indicates that the following text contains additional important
NOTE
information.
State of California Proposition 65 Warning (US only)
This product contains chemicals known to the State of California to cause
WARNING
cancer and birth defects or other reproductive harm.
For battery recycling go to call2recycle.org
L i - i o n
or call 1-800-822-8837
ENGLISH-03
Safety information
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should be observed, including the following:
READ ALL INSTRUCTIONS BEFORE USING YOUR POWERbot.
Unplug from outlet when not in use and before conducting maintenance.
WARNING: To reduce the risk of re, electric shock, or injury:
GENERAL
• Use only as described in this manual.
• Do not operate POWERbot or the battery charger / docking station if it has been damaged in any way.
• If the vacuum cleaner is not working as it should, has been dropped, damaged, left outdoors, or dropped in water, contact an authorized Samsung service center.
• Do not handle the battery charger / docking station or POWERbot with wet hands.
• Use only on dry, indoor surfaces.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Do not let children clean or perform user maintenance on the POWERbot without adult supervision.
• Place the cords from other appliances out of the area to be cleaned.
• Do not operate the vacuum in a room where an infant or child is sleeping.
• Do not operate the vacuum in an area where there are lit candles or fragile objects on the oor.
• Do not operate the vacuum in a room that has lit candles on furniture that the vacuum may accidentally hit or bump into.
• Do not allow children to sit on the vacuum.
• Do not use the vacuum on a wet surface.
Battery charger / Docking station
• Do not modify the polarized plug to t a non-polarized outlet or extension cord.
• Do not use outdoors or on wet surfaces.
• Unplug the battery charger / docking station from the outlet when not in use and before servicing.
• Use only the battery charger / docking station supplied by the manufacturer to recharge the POWERbot.
• Do not use with a damaged cord or plug or a loose power outlet.
• Do not pull or carry by the cord, use the cord as a handle, close the door on the cord, or pull the cord around sharp edges or corners. Keep the cord away from heated surfaces.
ENGLISH-04
• Do not use extension cords or outlets with inadequate current carrying capacity.
• Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
• Do not mutilate or incinerate batteries as they will explode at high temperatures.
• Do not attempt to open the battery charger / docking station. Repairs should only be carried out by a qualied Samsung service center.
• Do not expose the battery charger / docking station to high temperatures or allow moisture or humidity of any kind to come into contact with the battery charger / docking station.
POWERbot
• Do not use to pick up hard or sharp objects such as glass, nails, screws, coins, and etc.
• Do not use without a lter in place. When servicing the unit, never put ngers or other objects into the fan chamber in case the unit accidentally turns on.
• Do not put any objects into openings. Do not use with any openings blocked; keep openings free of dust, lint, hair, and anything that may reduce air ow.
• Do not use to pick up toxic materials (chlorine bleach, ammonia, drain cleaner, etc.).
• Do not use to pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use to pick up ammable or combustible liquids such as gasoline or use in areas where they may be present. Also do not use in:
– Locations with candles or desk lamps on the oor. – Locations with unattended res (re or embers). – Locations with distilled alcohol, thinner, ashtrays with burning cigarettes, etc.
• Do not use POWERbot in an enclosed space lled with vapors given off by oil based paint, paint thinner, moth proong substances, ammable dust, or other explosive or toxic vapors.
• Leaks from battery cells can occur under extreme usage or temperature conditions. If the liquid gets on skin, wash quickly with water. If the liquid gets into eyes, ush them immediately with clean water for a minimum of 10minutes. Seek medical attention.
SAVE THESE INSTRUCTIONS
POLARIZED PLUG INSTRUCTIONS
• To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will t in a polarized outlet only one way. If the plug does not t fully in the outlet, reverse the plug. If it still does not t, contact a qualied electrician to install a proper outlet. Do not modify the plug in any way.
ENGLISH-05
Safety information
REGULATORY NOTICE
1. FCC Notice
CAUTION
FCC STATEMENT:
FCC CAUTION:
• Any changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• This device complies with Part 15 of FCC Rules. Operation is Subject to following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received including interference that
cause undesired operation.
• For products available in the US and Canadian markets, only channels 1~11 are available. You cannot select other channels.
• This equipment has been tested and found to comply within the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
• This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorienting or relocating the receiving antenna – Increasing the separation between the equipment and receiver – Connecting the equipment to an outlet that is on a different circuit from the
radio or TV.
– Consulting the dealer or an experienced radio/TV technician for help.
FCC RADIATION EXPOSURE STATEMENT:
• This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated so there are at least 8 inches (20 cm) between the radiator and your body. This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.
ENGLISH-06
2. IC Notice
• The term “IC” before the radio certication number only signies that Industry Canada technical specications were met. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
• This Class B digital apparatus complies with Canadian ICES-003.
• Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.
• For products available in the US and Canadian markets, only channels 1~11 are available. You cannot select other channels.
IC RADIATION EXPOSURE STATEMENT:
• This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated so there are at least 8inches (20cm) between the radiator and your body. This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.
Open Source License Notice
• This device uses open source software. Open Source Licenses are available on the product menu.
• Tap “Settings > Network > Software Update > Legal Information” on the device for more details.
ENGLISH-07
Safety information
WARNING
f To prevent the risk of electric shock or
re:
– Do not damage the power cord. – Do not pull the power cord too hard or
touch the power plug with wet hands.
– Use only power sources that provide
between 100 and 240 volts. Do not plug the POWERbot into a multi-outlet power strip. Do not place the power cord where it can be stepped on, tripped over, or where the POWERbot can run over it.
– Do not use a damaged power plug, power
cord, or loose power outlet.
f Clean dust or any foreign matter off the
prongs of the power plug.
– There is a risk of electric shock or
malfunction.
WARNING
f Do not use the POWERbot near
combustible materials.
– Do not place or use near candles, desktop
lamps, or replaces or near combustible materials such as gasoline, alcohol, thinners etc.
f The POWERbot is intended for specic
household use. Do not use it in an attic, basement, storage area, industrial building, outside, in places with moisture (such as a bathroom or laundry room), on a table or on shelves.
– The POWERbot can be damaged or
malfunction.
f Be sure the POWERbot does not pass
through or touch any kind of liquid.
– The POWERbot can be severely damaged
and it may contaminate other areas if the wheels pass through liquid.
f Attach the boundary markers to places
where the POWERbot may fall such as the top of a staircase or a bannister to prevent product damage and injury.
– Please keep the cliff sensor clean at all
times for safety.
Power related
Before use
ENGLISH-08
f Do not spill any liquid on the docking
station.
– There is a risk of re or electric shock.
f Do not use the docking station for
anything other than its intended purpose.
– There is a risk of re or severe damage to
the docking station.
f Always keep the cliff sensor clean for
your safety.
WARNING
f If any abnormal sounds, smells, or smoke
come from POWERbot, immediately shut off the POWERBOT using the emergency switch on the bottom of POWERbot, and then contact a Samsung service center.
WARNING
In use
Cleaning and maintenance
f If the power cord is damaged, contact a
Samsuing service center to get it replaced by a certied repairman.
– There is a risk of re or electric shock.
f Contact a Samsung Electronics service
center if you need to replace the batteries.
– Using batteries from other products can
cause the POWERbot to malfunction.
CAUTION
f If a brush or brush cover is not assembled
correctly, scratches may occur on the oor, or product malfunction may occur.
f Before operating the POWERbot, remove
the objects which could break such as a frame, mirror, and porcelain items so that the POWERbot works without interruption.
f Insert the dustbin before using the
POWERbot.
Before use
f For proper automatic recharging, do the
following:
– Always turn on the power of the docking
station.
– Install the docking station where the
POWERbot can nd it easily.
– Do not leave any object in front of the
docking station.
f When installing the docking station, do
not leave the cord on the oor where the POWERbot can run over it.
f Do not use POWERbot on black colored
oors.
– The POWERbot may not be able to operate
normally.
f Do not place any objects within 1.6ft
(0.5m) of either side of the docking station or within 3.3 ft (1m) of the front of the docking station.
f Make sure the docking station's charging
contact is not damaged and is free of foreign matter.
f Do not install the docking station in an
area with a dark oor.
– If the oor around the docking station is
dark, recharging is hindered.
f Move any obstacles that may disturb
POWERbot's movement (such as a children's indoor swing or slide) before cleaning.
f Do not use the POWERbot in a place
which is narrower than its turning radius (1.6 ft/0.5 m or less).
f To clean all areas of your house, open all
rooms and attach the boundary markers to places where the POWERbot could get damaged such as a front door, veranda, bathroom, or stairs.
f For areas with low clearance where
the POWERbot may get stuck, attach the boundary markers to prevent the POWERbot from getting in.
CAUTION
In use
f Using the POWERbot on thick carpet may
damage both the POWERbot and the carpet.
– The POWERbot cannot pass over carpet that
is thicker than 0.4in (1cm).
f Do not use the POWERbot on tables or
other high surfaces.
– There is a risk of damage if it falls.
f The POWERbot may bump into chair or
desk legs. Move them out of the away for faster, more efcient cleaning.
f When the POWERbot is operating, do not
lift it up or carry it to another area.
f Do not hold the POWERbot by its driving
wheels when carrying it to another area.
f Do not put any objects on top of the
POWERbot and camera since this may cause the POWERbot to malfunction.
f Remove any large pieces of paper or
plastic bags from the area to be cleaned before using the POWERbot since they may block the POWERbot's intake.
f Do not aim the red pointer directly at
people or animals.
f Do not lie down near the POWERBOT
when it is running.
– Your hair may be caught in the brush,
resulting in physical injury.
CAUTION
Cleaning and maintenance
f To prevent any damage to the POWERbot:
– Do not clean the POWERbot by spraying
water directly onto it or using benzene, thinner, acetone or alcohol to clean it.
f Do not disassemble or try to repair the
POWERbot yourself. Repairs should only be done by a certied repairman.
f Always keep the obstacle sensor, cliff
sensor, and camera clean.
– If foreign matter accumulates, the sensors
may malfunction.
ENGLISH-09
Installation
The docking station must be plugged in and turned on at all times.
Install the docking station in a place without obstacles and where there is no danger of falling.
About 3.3 ft
About
1.6 ft
(0.5 m)
(1 m)
About
1.6 ft
(0.5 m)
DC-IN
Connect the
battery charger
1
jack to the docking station
Connect the
power cord
2
to the battery charger
The side with the sticker attached must face down.
ENGLISH-10
Connect the
power plug to
3
the outlet
Accessories
or
Remote control
(Optional)
Docking station Power cord Battery charger Boundary markers
Accessories may differ depending on the models. Refer to page 17 for the installation of boundary markers.
Batteries (AAA type)
(Optional)
User manual Spare lter (Optional)
(Optional)
Installation note
Note
f Install the docking station in a place where the oor is level and the wall is straight. f It is best to install the docking station along the grain of wooden oors. f If the emergency switch is off, the POWERbot will not charge even if it is docked in the
docking station.
f Always turn on the power of the docking station.
– If power is not supplied to the docking station, the POWERbot cannot nd it and cannot
automatically recharge.
– If the POWERbot is left detached from the docking station, the battery will drain.
f If the POWERbot is in sleep mode, power will not come on even if the emergency switch is
turned off and then on. Press and hold the [Start/Stop] button on the POWERbot to turn the sleep mode off.
ENGLISH-11
Charging
After completely charging the POWERbot for the rst time (after purchase), it can be used for 60 min. in Nomal ( ) mode. (Refer to the page 41 for the charging time.)
Smart Charging
If the POWERbot's charge runs low while it is in Auto clean mode, it will automatically return to the docking station to recharge, and then will return to the cleaning area after its battery is 2/3rds charged. (Maximum: 2 times.)
• Rated input voltage of
WARNING
this product is 100­240V~.
<SR1AM7010U Series>
<SR1AM7040W /
SR2AM70 Series>
Turn on the
emergency switch
1
on the bottom
You must turn on the emergency switch to turn on the POWERbot.
Press and release the
button.
Manually charge the POWERbot by
2
placing it in the docking station
Make sure the charging pins on the POWERbot and the docking station are aligned.
ENGLISH-12
Check the charging
status
3
For the SR1AM7010U Series, the battery indicator blinks at 1 second intervals during charging. The indicator will remain on when the battery is fully charged.
For SR1AM7040W / SR2AM70 Series, each section of the " " will turn on successively to indicate charging progress and "FULL" will appear when charging is complete.
Automatic charging
1. SR1AM7010U Series
If the battery indicator blinks at 0.4 sec. intervals, the POWERbot will automatically return to the docking station to recharge.
2. SR1AM7040W / SR2AM70 Series
When the battery indicator blinks during cleaning, the POWERbot will return to the docking station to charge itself automatically.
Recharging
You can command the POWERbot to recharge at the docking station while it is cleaning.
Low battery (Lo)
You can manually charge the POWERbot by placing it in the docking station.
Steps to take if automatic recharging is not occuring:
Reconsider the location of the docking station when:
fthe docking station is located in a place where the POWERbot cannot easily access it.
fthe distance between the docking station and POWERbot is over 16.4ft (5m).
– It may take a long time for the POWERbot to
return to the docking station for recharging
Manually charge the POWERbot when:
fthe docking station is located in a corner fthe battery is fully exhausted fthe POWERbot is immobilized by an obstacle
(furniture, etc.) fthe POWERbot can't climb a threshold near
the docking station (The maximum height of a threshold the POWERbot can climb is about
0.6in (1.5cm)). fthe battery indicator blinks and "Lo" is
displayed fthe battery indicator blinks (Applicable to
SR1AM7010U Series) fthe POWERbot is set to the Spot clean or
Manual clean mode
ENGLISH-13
Using POWERbot
You must turn on the emergency switch on the bottom of the unit before using POWERbot.
Turning the power on/off
Press the button for more than 3seconds
• When POWERbot is not used for 30 min.;
WARNING
SR1AM70U / SR2AM70U series: Enters energy-saving mode. SR1AM70W / SR2AM70W series: Automatically returns to the docking
station to be charged.
Starting Auto clean mode
Press and release this button. The POWERbot moves and automatically cleans the set areas only once.
Stop cleaning: Press and release the button
Using Spot clean mode
The POWERbot cleans a localized area intensely.
Recharging/Energy-saving mode
fRecharging You can command POWERbot to recharge at the docking station
automatically while it is cleaning by pressing this button. fEnergy-saving mode Refer to page 17.
ENGLISH-14
Selecting cleaning modes
Cleaning mode How to select
Auto clean
Spot clean
Displayed icons
SR1AM7040W
SR2AM70
SR1AM7010U
Press the [A,B type
Repeat clean
Manual clean
If POWERbot fails to return to the docking station, it will enter energy-saving mode and the display
panel will be turned off.
To exit the energy-saving mode, press the [Start/Stop
the remote control.
If cleaning in Auto clean mode is completed within 15 minutes, POWERbot cleans 1 more time.
[C type ] on the remote controller rst, and then press the [Start/Stop ].
You can select manual clean
mode using the direction control buttons on the remote control.
],
-
-
] or [Power ] button on the main body or
ENGLISH-15
Using POWERbot
Cleaning method for each mode
About 4.9ft (1.5m)
About 4.9ft (1.5m)
Auto clean
Automatically cleans the set areas only once.
SR1AM7010U series:
Cleans repeatedly until the battery is depleted.
Spot clean
Cleans a localized area intensely. It can be used to clean bread or cookie crumbs.
Manual clean
You can move POWERbot with the remote control to clean the desired spot.
This function is not
available on the SR1AM7010U series.
Repeat clean
Cleans repeatedly until the battery is depleted.
This function is not
available on the SR1AM7010U series.
Note
f If you select Auto clean or Repeat clean, the POWERbot cleans the area near the docking station rst.
Using special cleaning functions
Cleaning
function
Intelligent
power control
Operation
When the POWERbot detects a
carpet in normal mode, it will automatically operate with stronger suction power.
SR1AM7040W SR2AM70
Displayed icons
SR1AM7010U
When the POWERbot detects an
edge or corner in Auto clean or
Edge clean
master
Spot clean, the auto shutter tool operates and approaches the edge or corner section to clean.
fStraight edge (One time cleaning) fCorner (Cleans twice)
ENGLISH-16
About the boundary markers
To prevent the POWERbot from entering the following areas, place the boundary markers on the oor in an shape at intervals of about 5.9in (15cm).
About 5.9in (15cm)
About 1.9in
Boundary
markers
Where a raised spot exceeds 1.9in (5cm) Where there is a slide, swing, replace, or any
Above 0.6in (1.5cm)
boundary
markers
Where a threshold is higher than 0.6in (1.5cm) Where there is risk of falling such as near
(5cm)
ammable substance or moisture.
stairs, porches, or guardrails.
Boundary
markers
About 5.9in (15cm)
Boundary markers
Using Energy-saving mode
You can selectthe Energy-saving modeto save energy during battery charging.Energy-saving mode turns off all functions except battery charging.Use it to reduce powerconsumptionwhile you are away from home for an extended period of time.
How to select or cancel Displayed icon
Press for 5 sec.
About 3seconds
later, the previous indicator will appear.
Note
f If you select the Auto/Max/Manual clean mode or press the Point cleaning button, the
Energy-saving mode will be cancelled.
f When Energy-saving mode is on, setting the schedule will cancel Energy-saving mode.
– If you select the Energy-saving mode after setting the schedule, the schedule will not be cancelled.
f If the docking station is off, Energy-saving mode will be cancelled. f If the battery is completely at, place the POWERbot on the docking station, and then press
the [Start/Stop
] button on the main body.
ENGLISH-17
<SR1AM7010U series only>
Blinking Blinking
Using the remote control
[A Type] [B Type]
1 1
3 3
1, 2 1, 2 5 5
[C Type]
4 2 2
4
Refer to page 23
1
3
1, 2 5
4
4
Refer to page 23
6 2 4
4
Refer to page 24
ENGLISH-18
[A Type] / [B Type]/ [C Type]
1 Power / Recharging / Start/Stop
Power
Recharging
Start/Stop
2 Cleaning modes
Auto clean
Spot clean
Repeat clean
3 Suction power
Turbo mode
Turn POWERbot's power on/off
Select to recharge POWERbot at the docking station automatically
Select to start or stop the cleaning process
Select to clean all set areas only once and then have the POWERbot automatically return to the docking station.
Select to clean a localized area intensely
Select to clean repeatedly until the battery becomes very low and the battery level indicator blinks
Select to clean with the strongest suction power
Normal mode
Quiet mode
Select to clean with moderate suction power
Select to clean with lower operational noise
4 Additional function
Each time you press this button, Sound Effects
Sound
Remote control
SR1AM7010U5 series only: Star wars (Mute function is not available.) Turning the emergency switch off and then on will not cancel or change the settings.
Mute is selected in sequence <SR1AM7040W9 series only> Star wars Sound Effects Mute
Select to turn the Wi-Fi function on or off
ENGLISH-19
Using the remote control
5 Manual clean mode & Direction control
Move forward
Turn left
Turn right
Moving backward is not available.
Select to move forward
Select to turn left
Select to turn right
6 Point cleaning
Available only with C type remote controllers.
You can use the remote control to direct the POWERbot to clean a desired spot while the POWERbot is cleaning.
Point the red light on the oor within 1.6ft (0.5m) of the POWERbot's location.
Press and hold the Point cleaning button to move the red light to the desired spot. The POWERbot will follow the light while cleaning.
1.6ft (0.5m)
Operating distance of the remote control
Height of the
remote control
Operating
distance
Height of the remote control
Operating distance
Inserting batteries
Open the battery cover by lifting it up while pressing the locking tab. Insert the batteries as shown in the illustration, and then close the cover until it clicks into place.
ENGLISH-20
1.6ft (0.5m) 3.3ft (1m) 4.9ft (1.5m)
About 4.9ft
(1.5m)
About 6.6ft
(2m)
About 9.8ft
(3m)
Name of each part
2
6
5
3
7
8
1
4
2
Top
1. Display panel
2. Remote control signal receiver
3. Obstacle sensor
4. Dustbin
5. Camera
6. Dustbin button
7. Bumper sensor
8. Auto shutter tool
4
2
3
4
5
5
10
7
1
4
8
6
9
Bottom
1. Charging pins
2. Brush
3. Brush cover
4. Cliff sensor
5. Roller
6. Battery cover
7. Brush cover button
8. Driving wheel
9. Emergency switch
10. Auto shutter tool
ENGLISH-21
Name of each part
2
1
4
1
2
6
12 138 11109
14
3
5
6
3
4
5
7
16
15
Display panel
<SR1AM7010U series>
1. Daily schedule
2. Normal/Turbo mode
3. Battery indicator
4. Spot cleaning button, dailyschedule(3sec)
5. Start/Stop button, Turbomode(3sec)
6. Recharging button
<SR1AM7040W / SR2AM70 series>
1. Mute
2. Information Indicator
3. *Smart Control Off/On indicator
4. *Wi-Fi
5. Battery indicator
6. One-time/Daily schedule
7. Number display
8. Spot clean mode
9. Manual clean mode
10. Repeat clean mode
11. Quiet mode
12. Normal mode
13. Turbo mode
14. Spot cleaning button
15. Start/Stop button
16. Recharging button
SR1AM70W / SR2AM70W : Wi-Fi supported model
ENGLISH-22
Setting time/schedule
[A Type, B Type] Only Auto clean mode can be scheduled.
Setting the time
You must set the current time before using the One-time/daily schedule function.
Start setting Select "Hour" Select "Minute"
Select "AM/PM"Setting complete
Skip to previous, next setting
Setting the schedule
You can set/cancel the schedule only when the POWERbot is docked in the docking station.
Start setting Select "One-time" or
"Daily" schedule
Cancelling during setup
fThe setting will be canceled automatically if there's no input for 7seconds.
Cancelling One-time/Daily schedule
When both One-time/ Daily schedule is set
Press for 3 sec. Select the schedule Cancel complete
When either one of One-time or Daily schedule is set
Select "Hour"
or
Press for 3 sec.
Select "Minute"Select "AM/PM"Setting complete
Skip to previous, next setting
or
ENGLISH-23
Setting time/schedule
[C Type] Only Auto clean mode can be scheduled.
Setting the time
You must set the current time before using the One-time/daily schedule function.
Start setting Select "Hour" Select "Minute"
Select "AM/PM"Setting complete
Skip to previous, next setting
Setting the schedule
You can set/cancel the schedule only when the POWERbot is docked in the docking station.
Start setting Select "One-time" or
"Daily" schedule
Cancelling during setup
fThe setting will be canceled automatically if there's no input for 7seconds.
Cancelling One-time/Daily schedule
When both One-time/ Daily schedule is set
Press for 3 sec. Select the schedule Cancel complete
When either one of One-time or Daily schedule is set
Select "Hour"
Select "Minute"Select "AM/PM"Setting complete
Skip to previous, next setting
or or
Press for 3 sec.
ENGLISH-24
[SR1AM7010U series] For the models which do not include a remote control, you can set a daily schedule as described below.
Setting the schedule
You can set/cancel the schedule only when the POWERbot is docked in the docking station.
Press for 3 seconds.
The time you pressed the button will be set as the time that the POWERbot is scheduled to begin
cleaning. The POWERbot will automatically begin cleaning every day at that scheduled time.
When the schedule LED is turned
on, the daily schedule is set.
Cancelling daily schedule
When a daily schedule is set
Press for 3 seconds.
ENGLISH-25
Cleaning and maintaining
You must turn off the emergency switch before cleaning the POWERbot.
Cleaning the dustbin
Press the button to
1
remove the dustbin
Detach the cyclone
4
unit from the dustbin cover, and then wash the dustbin and the lter
Remove the dustbin
2
cover
Reassemble the
5
dustbin
Cleaning the sensors and the camera
Remove dust in the
3
dustbin and cyclone unit
'Click'
Reinsert the dustbin
6
into the main body until it clicks
Lightly wipe with a soft cloth. Do not use water or cleaning solutions.
Camera
Front sensor
window
ENGLISH-26
Cliff sensors
Rear sensor
window
Cleaning the brush and Auto shutter tool
Brush design may differ depending on the model.
Remove the
1
brush cover
Reassemble the brush
5
Remove the
2
brush
Cleaning the Driving wheel
Clean the
3
brush
Reassemble the brush cover
6
Clean the auto
4
shutter tool
Put a soft cloth on the oor and place
1
POWERbot upside-down on the cloth.
ENGLISH-27
Use a blunt rod or tweezers to remove
2
foreign matter.
Samsung Connect App
The Samsung Connect App is only compatible with models that have a Wi-Fi function.
Setting up the wireless router
f Please refer to the user manual of your wireless router if you have access problems. f Samsung POWERbot supports only Wi-Fi 2.4 Ghz. f Samsung POWERbot supports IEEE 802.11b/g/n and Soft-AP.
– IEEE 802.11n is recommened.
f Samsung POWERbot supports only DHCP (Dynamic Host Conguration Protocol). Please
make sure that the DHCP server option is activated on your wireless router.
f POWERbot supports the WEP-OPEN, WPA-PSK/TKIP, and WPA2-PSK/AES for the
authentication and encryption protocols.
– WPA2-PSK/AES is recommended. – Conrm that your router has a unique SSID and password.
f The quality of your wireless network connection may be inuenced by the surrounding
wireless environment.
f If your Internet service provider has permanently registered the MAC address (a unique
identication number) of your PC or modem, your POWERbot may not be able to connect to the Internet. Ask your Internet service provider about the procedure to connect an apparatus other than a PC to the Internet.
f If your internet service provider requires your ID or password to connect to the internet,
your POWERbot may not be able to connect. If this is the case, you must enter your ID or password when connecting to the Internet.
f The POWERbot may not be able to connect to the Internet because of rewall issues.
Contact your Internet service provider to resolve these issues.
f Some wireless routers may transmit an abnormal Domain Name Server (DNS) address even
if the Internet is not connected. If this occurs, contact the manufacturer of your wireless router and your Internet service provider.
f If you still cannot connect to the Internet even after trying the procedure provided by your
Internet service provider, please contact an authorized Samsung service center.
f If your router is not a Wi-Fi certied product, The POWERbot may not be able to connect to
the Internet.
ENGLISH-28
Downloading the Samsung Connect App
f Download and install the Samsung Connect app from the markets (Google Play Store, Apple
App Store, or Samsung Galaxy Apps). To nd the app, use the keyword “Samsung Connect”.
Note
f Samsung Connect is incompatible with tablets and some mobile devices.
– Android 6.0 or later (at least 2GB of RAM) is recommended.
f iPad and some mobile devices may not be supported.
– iOS 10.0 or later / iPhone 6 or later is supported.
f Visit Play Store or App Store to see if your mobile device is compatible with Samsung
Connect.
f The supported features are subject to change without any prior notice.
Setting up a Samsung account
f You must sign in to a Samsung account before using the Samsung connect app. f To set up a Samsung account, you can follow the directions provided by the Samsung
Connect app.
f Or, if you have a Samsung smartphone, you can add your Samsung account in the setting
app of your smartphone. Then, it will automatically sign in to your Samsung account.
ENGLISH-29
Samsung Connect App
Adding a device to the Samsung Connect APP
1. Connect your smartphone to your wireless router.
2. Launch the Samsung Connect app on your smartphone.
3. If a pop-up saying that a new device has been found appears, tap ADD NOW. – If the pop-up doesn’t appear, tap the + button and select the device which you want to connect
from the list of AVAILABLE DEVICES.
– If your device doesn’t appear in the list, add the device manually by selecting the device type and
selecting the specic device model.
4. [Android] The connection to your device will be progressed automatically. – [iOS] Open the setting app, and select [robot vacuum] Samsung in the Wi-Fi list.
5. Provide the authentication when you are directed to do so.
6. [Android] The connetion to your wireless router will be progressed automatically. – [iOS] Open the setting app, and select the wireless router in the Wi-Fi list.
7. The remaining setup will be automatically done. Then, a new Device Card will be added.
Note
f If you cannot complete the product registration, please take the following steps.
– Try the registration procedure again as you have directed by the pop-up messages. – Conrm that the UPnP option of your wireless router is active, and then try the registration
procedure again.
– Conrm that your wireless router is operating in wireless mode, and then try the registration
procedure again.
– If you have two or more POWERbots, turn off the other POWERbots, and then try to register your
POWERbot again.
– If there is any other wireless router that has the same SSID as your wireless router, the
registration might be failed.
f Smart control and Wi-Fi indicator
Smart control is blocked. (The remote controller can still
On
be allowed.)
Off Smart control is allowed.
On The POWERbot is connected to the wireless router.
Off The POWERbot is trying to connect the wireless router.
f When the Smart control is blocked, you cannot control the POWERbot on your smartphone. f The POWERbot and your smartphone are not connected to the same wireless router, a
response delay may occur depending on your network environment.
ENGLISH-30
Loading...
+ 98 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use