Samsung SNV-8080 User Manual

Download

Page 1

NETWORK CAMERA

User Manual

SNB-8000/SNV-8080

Page 2

Network Camera

User Manual

Trademark

The name of thi s product is the reg istered tradema rk of Samsung Techwin C o., Ltd. Other trad emarks mention ed in this manual are th e registered trad emark of their resp ective company.

Restriction

Samsung Techwi n Co., Ltd shall reser ve the copyrigh t of this document. U nder no circumst ances, this docu ment shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.

Disclaimer

Samsung Techwi n makes the best to ver ify the integri ty and correct ness of the conten ts in this document , but no formal guar antee shall be provi ded. Use of this do cument and the subse quent results sha ll be entirely on the u ser’s own responsib ility. Samsung Techwi n reserves the ri ght to change the con tents of this docum ent without prio r notice.

Design and specifications are subject to change without prior notice.

The initi al administra tor ID is “admin” a nd the passwor d should be set wh en logging in for t he first time.

Please ch ange your pass word every thr ee months to saf ely protect p ersonal inf ormation and t o prevent the damage of the information theft. Please, t ake note that it ’s a user’s respo nsibility fo r the securit y and any other pr oblems cause d by mismanaging a password.

is the regist ered logo of Samsun g Techwin Co., Ltd.

Page 3

overview

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings, Install in accordance with the manufacturer’s

instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized

plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/ accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by

the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lighting storms or when unused for

long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2”

and rated from 24 Vac (50/60 Hz) min 0.9 A or 12 Vdc, min 0.9 A.

● OVERVIEW

English _3

Page 4

overview

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT.

Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance with the installation instructions.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

4_ overview

Page 5

Class construction

An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection.

Battery

Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

Disconnection Device

Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location.

When used outside of the U.S., it may be used HAR code with fittings of an approved agency is employed.

CAUTION

Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

The CVBS out terminal of the product is provided for easier installation, and is not recommended for monitoring purposes.

Please use the input power with just one camera and other devices must not be connected.

The ITE is to be connected only to PoE networks without routing to the outside plant.

● OVERVIEW

English _5

Page 6

overview

Please read the following recommended safety precautions carefully.

yDo not place this apparatus on an uneven surface. yDo not install on a surface where it is exposed to direct sunlight, near

heating equipment or heavy cold area. yDo not place this apparatus near conductive material. yDo not attempt to service this apparatus yourself. yDo not place a glass of water on the product. yDo not install near any magnetic sources. yDo not block any ventilation openings. yDo not place heavy items on the product.

User’s Manual is a guidance book for how to use the products.

The meaning of the symbols are shown below.

yReference : In case of providing information for helping of product’s usages yNotice : If there’s any possibility to occur any damages for the goods and

human caused by not following the instruction

 Please read this manual for the safety before using of goods and keep it in

the safe place.

6_ overview

Page 7

CONTENTS

OVERVIEW

INSTALLATION &

CONNECTION

NETWORK CONNECTION

AND SETUP

3 Important Safety Instructions 9 Product Features 10 Recommended PC Specifications 10 Recommended Micro SD/

SDHC/SDXC Memory Card Specifications

11 NAS recommended specs 11 What’s Included 15 At a Glance (SNB-8000) 18 At a Glance (SNV-8080)

21 Mounting the Lens (SNB-8000) 23 Installation (SNV-8080) 32 Inserting/Removing a Micro SD

Memory Card

34 Memory Card Information

(Not Included)

35 Connecting with other Device

43 Connecting the Camera Directly

to Local Area Networking

44 Connecting the Camera Directly

to a DHCP Based DSL/Cable Modem

45 Connecting the Camera Directly

to a PPPoE Modem

46 Connecting the Camera to a

Broadband Router with the PPPoE/Cable Modem

47 Buttons used in IP Installer 48 Static IP Setup 52 Dynamic IP Setup 53

Port Range Forward (Port Mapping) Setup

55 Connecting to the Camera from a

Shared Local PC

55 Connecting to the Camera from a

Remote PC via the Internet

● OVERVIEW

English _7

Page 8

overview

WEB VIEWER

SETUP SCREEN

APPENDIX

136

56 Connecting to the Camera 58 Password setting 58 Login 59 Installing STW WebViewer Plugin 61 Using the Live Screen 65 Playing the recorded video

72 Setup 72 Basic Setup 85 Video & Audio setup 101 Network Setup 110 Event Setup 115 NAS (Network Attached Storage)

guide

129 System Setup 135 Viewing profile information

136 Specification 142 Product Overview 144 Troubleshooting 146 Open Source Announcement

8_ overview

Page 9

PRODUCT FEATURES

• Full HD Video Quality

• Multi-Streaming

This network camera can display videos in different resolutions and qualities simultaneously using different CODECs.

• Web Browser-based Monitoring

Using the Internet web browser to display the image in a local network environment.

• Alarm

When an event occurs, video is either sent to the email address registered by the user, sent to the FTP server, saved in a Micro SD card or NAS, or a signal is sent to the alert output terminal.

• Tampering Detection

Detects tempering attempts on video monitoring.

• Motion Detection

Detects motion from the camera’s video input.

• Audio Detection

Detects sound louder than a certain level specified by user.

• Auto Detection of Disconnected Network

Detects network disconnection before triggering an event.

• ONVIF Compliance

This product supports ONVIF Profile-S. For more information, refer to www.onvif.org.

● OVERVIEW

English _9

Page 10

overview

RECOMMENDED PC SPECIFICATIONS

• CPU : Intel Core 2 Duo 2.4 GHz or higher (for using 1920x1080 30 fps)

Intel Core i7 2.8 GHz or higher (for using 1920x1080 60 fps)

Web Plug-in is optimized to SSE 4.1 Instruction Set.

• Resolution : 1280X1024 pixels or higher (32 bit color)

• RAM : 2GB or higher

• Supported OS : Windows XP / VISTA / 7 / 8, MAC OS X 10.7

• Supported Browser : Microsoft Internet Explorer (Ver. 11 ~ 8)

Mozilla Firefox (Ver. 19 ~ 9)

Google Chrome (Ver. 25 ~ 15)

Apple Safari (Ver. 6.0.2(Mac OS X 10.8, 10.7 only), 5.1.7) ※ Mac OS X only

Windows 8 is supported only in the Desktop mode.

Neither a beta test version unlike the version released in the company website nor the developer version will

be supported. For IPv6 connection, Window 7 or higher is recommended.

For Mac OS X, only the Safari browser is supported.

• Video Memory : 256MB or higher

If the driver of the video graphic adapter is not installed properly or is not the latest version, the

video may not be played properly.

For a multi-monitoring system involving at least 2 monitors, the playback performance can be

deteriorated depending on the system.

RECOMMENDED MICRO SD/SDHC/SDXC MEMORY CARD SPECIFICATIONS

• Recommended capacity : 4GB ~ 64GB

• For your camera, we recommend you use a memory card from the following

manufacturers:

Micro SD/SDHC/SDXC Memory Card : Sandisk, Transcend

• For the framerate below 30 fps, it is recommended to use the specification memory card

of Class 6 or higher.

• For the framerate over 31 fps, it is recommended to use the specification memory card of

Class 10 UHS or higher.

10_ overview

Page 11

NAS RECOMMENDED SPECS

• Recommended capacity : 200GB or higher is recommended.

• Simultaneous access : One unit of NAS can accept a maximum of sixteen camera accesses.

• For this camera, you are recommended to use a NAS with the following manufacturer’s specs.

Recommended products Available sizes

Netgear NAS A maximum of 16 cameras can access simultaneously.

Synology NAS A maximum of 16 cameras can access simultaneously.

When you use Netgear’s NAS equipment, do not allocate the capacity for use.

If you use NAS equipment for purposes other than video saving, the number of accessible

cameras may be reduced.

WHAT’S INCLUDED

Please check if your camera and accessories are all included in the product package.

Appearance Item Name

Camera

Mircro SD

+ -

AC 24V / DC 12V

RESET

VIDEO

Quantity

Description Model Name

SNB-8000 or

SNV-8080

● OVERVIEW

Instruction book, Installer S/W CD

SNB-8000 SNV-8080

English _11

Page 12

overview

Appearance Item Name

Quick Guide

(Optional)

Warranty card

(Optional)

Cable for the testing

monitor

Power Terminal Block 1 Plugged in the power plug SNV-8080

Template

C Mount Adapter 1

Automatic Iris Lens

Connector

Quantity

Description Model Name

Used to test the camera

connection to a portable display

Product installation guide

Used to install the C Mount

camera lens

Useful for camera lens

installation

device

SNB-8000 SNV-8080

SNV-8080

SNB-8000

12_ overview

Page 13

Appearance Item Name

Quantity

Description Model Name

6-position Terminal Block 1 Used for alarm in/out terminals SNB-8000

Used for dome cover

L Wrench 1

disassembly, assembly and

camera installation.

CAUTION: Be ware of the Rated Voltage and Polarity

of the power connection.

Power Cable 1 Used to plug into the power port SNV-8080

Audio/alarm cable 1

Cable bush 1

Tapping Screw 3

Used to connect with the

audio and alarm port

Used to connect the LAN cable

with a diameter of Ø7~8.5.

Used for installation on the

wall or ceiling

For fixing a screw,

Plastic Anchor 3

Inserted in a hole

(reinforced anchoring force)

● OVERVIEW

SNV-8080

English _13

Page 14

overview

Appearance Item Name

Machine Screws 3

Drill bit 1

CS/C Lens

Indoor Buried Housing

Quantity

Options (not included)

Description Model Name

Used for assembling the dome

case when installing the product

on the pipe, wall mount, etc. or

blocking a hole.

Used for dome cover

disassembly, assembly and

camera installation.

Optional lens to be inserted in

Housing for installing indoor

buried type cameras

a camera

SNV-8080

SNB-8000

SNV-8080

14_ overview

Page 15

AT A GLANCE (SNB-8000)

Front Side

Item Description

Used to fix the camera on a mounting bracket.

The screw size : It is the specification for the screws used to fasten the

Mounting Bracket

Screw Hole

Auto Iris Lens

(Optional)

Auto Iris Lens

Connector

camera to the support. 1/4" - 20 UNC

L : 4.5mm±0.2mm (ISO Standard) or 0.197" (ASA Standard)

Installed on the lens adaptor.

Used to supply power and output signal to control the iris of the lens.

● OVERVIEW

Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you have applied

ethanol.

Mounting Bracket is not included.

For more information to use mounting bracket, refer to the product’s documentation.

English _15

Page 16

overview

Rear Side

a b

j i

Item Description

Micro SD Memory

Card Compartment

Audio terminal

Reset Button

Focus Adjustment

Button

Compartment for the Micro SD memory card.

AUDIO OUT Used to connect to speakers.

AUDIO IN Used to connect to a microphone.

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.

If you reset the camera, the network settings will be adjusted so that

DHCP can be enabled. If there is no DHCP server in the network, you must run the IP Installer program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network.

The button adjusts the focus of image automatically.

c d

16_ overview

Page 17

Item Description

Lightning protective

grounding port

Power Port Used to plug the power cable.

Network Port Used to connect the PoE or Ethernet cable for network connection.

Alarm I/O Port

Test Monitor Out

SD, Power Indicators

RS-485 port only supports direct connection with pan/tilt driver and external connections of the

RS-485 controller is not supported.

Used to discharge the lightning current safely outside in order to protect the camera.

ALARM IN

ALARM OUT Used to connect the alarm output signal.

GND Used for earth-grounding.

RS-485+ RS-485 Data line

RS-485- RS-485 Data line

Output port for test monitoring the video output. Use the test monitor cable to connect to a mobile display and check the test video.

POWER

Used to connect the alarm input sensor or external day/ night sensor.

ON : A memory card is inserted and operates normally.

Flashing : Failed to record, insufficient space, or inserted

abnormally.

OFF : Camera is off, camera is restarting, memory card is

not in place, or when record is off.

ON : While the power is on

OFF : If the power is off

● OVERVIEW

English _17

Page 18

overview

AT A GLANCE (SNV-8080)

Appearance

+ -

AC 24V / DC 12V

Item Description

Dome cover

Case cover used to protect the lens and the main unit.

Mircro SD

RESET

VIDEO

Camera Case

18_ overview

Housing part that covers the camera body.

Page 19

Components

+ -

AC 24V / DC 12V

RESET

VIDEO

b d ec f hg

Item Description

Lens Lens for the camera.

Power Port Port for power terminal block.

Test Monitor Out

Reset Button

Output port for test monitoring the video output. Use the test monitor cable to connect to a mobile display and check the test video.

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.

If you reset the camera, the network settings will be adjusted so that

● OVERVIEW

English _19

Page 20

overview

Item Description

Zoom/Focus Control

Button

Micro SD Memory

Card Compartment

Audio and alarm

cable port

Network Port Used to connect the PoE or Ethernet cable for network connection.

T Zoom in (Tele)

W Zoom out (Wide)

N Focusing on a near object (Near)

F Focusing on a far object (Far)

Focus Control Press this button for automatic focus control.

Compartment for the Micro SD memory card.

Plug in the audio and alarm cable to this port to connect with external alarm device/microphone/speaker.

20_ overview

Page 21

installation & connection

MOUNTING THE LENS (SNB-8000)

Disconnect the power before proceeding.

The C lens and CS lens are not included in the product package.

It is recommended that megapixel lens are use on this camera to optimise performance.

Mounting the CS lens on a camera

Turn the CS lens clockwise to attach it.

CS Lens

Mounting the C lens on a camera

Turn the C mount adapter included in the product package clockwise and turn the C lens clockwise.

● INSTALLATION & CONNECTION

C Lens

English _21

Page 22

installation & connection

Connecting the Auto Iris Lens connector

Plug the iris connector of the lens in the camera connecting groove.

Focusing

Select a target to film, turn the zoom lever of the lens to adjust the magnification and then focus the lens so that target is clearly displayed.

After focusing with the zoom lever of the lens, press the [FOCUS] button on the rear of the camera

to adjust the lens even more clearly.

22_ installation & connection

Page 23

INSTALLATION (SNV-8080)

This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the

external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.

Precautions before installation

Ensure you read out the following instructions before installing the camera:

• It must be installed on the area (ceiling or wall) that can withstand 5 times the weight of the camera including the installation bracket.

• Stuck-in or peeled-off cables can cause damage to the product or a fire.

• For safety purposes, keep anyone else away from the installation site. And put aside personal belongings from the site, just in case.

Disassembling

1. With the provided L-wrench and

drill bit, loosen 3 bolts on the dome cover counter clockwise to remove the cover.

Dome cover

● INSTALLATION & CONNECTION

Bolts

Camera Body

+ -

AC 24V / DC 12V

Camera Case

RESET

VIDEO

English _23

Page 24

installation & connection

Installation

1. Using the template provided as an accessory,

drill the screw installation hole(diameter of 6mm, minimal depth of 55mm) and firmly insert the plastic anchor provided as an accessory to the end.

2. Fit the bottom hole to the anchor hole and insert

and fix the taping screw (M4.5xL50).

3. Connect and arrange the necessary cables lest

that they should be damaged or twisted while installing the camera.

4. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for

the camera" section. (page 31)

5. Close the dome cover.

`To ensure waterproofing, tight up the fixing bolts using the L-wrench and drill bit.

VIDEO

RESET

AC 24V / DC 12V

VIDEO

+ -

RESET

AC 24V / DC 12V

+ -

24_ installation & connection

Page 25

Connecting waterproof power cable and LAN cable

1. Remove the dome cover and the case.

2. Pull out the long projected part of the rubber plug on

the bottom and remove it as shown in the figure.

Use an appropriate cable bush for the LAN cable to be

connected.

- Basic camera : Use the cable with a diameter of Ø5~6.5.

- Components provided : Use the cable with a diameter of Ø7~8.5.

3. Insert the power cable into the small hole made by

removing the projected part of the rubber plug in step 2 above, and lay the cable along the long groove.

4. Connect the power cable with the power terminal

block.

● INSTALLATION & CONNECTION

CAUTION: Be ware o f the

Rated Voltage and P olari ty

of the power conne ction .

English _25

Page 26

installation & connection

5. Insert the LAN cable into the large hole made by

removing the projected part of the rubber plug in step 2 above.

6. Remove the sheath with a cable cutter, and align the

cables.

7. Connect the LAN cable with a LAN connector, and

insert it into the LAN tool.

8. Connect the finished cable to the Ethernet port.

CAUTION: Be ware o f the

Rated Voltage and P olari ty

of the power conne ction .

26_ installation & connection

Page 27

Connecting alarm cable

1. Remove the dome cover and the case.

2. Pull out the rubber plug on the bottom as shown in

the figure.

3. Insert the alarm cable into the hole made by

removing the rubber plug in step 2, and connect the cable with the PCB alarm terminal.

4. Align the cable so that it should not be damaged or

jammed when installing the camera.

5. Put the rubber plug of the alarm cable into the hole.

6. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for the camera” section.

7. Attach the dome cover.

(page 31)

● INSTALLATION & CONNECTION

English _27

Page 28

installation & connection

Attaching to the unbundled adapter

Choose and purchase a necessary one of the following options (unbundled) that is suitable to the installation site or for your convenience.

1. Remove the dome cover from the case by referring to the “Disassembling” section. (page 23)

2. Use the provided machine screw to fix the camera case to the unbundled adapter.

3. Connect and arrange the necessary cables lest that they should be damaged or twisted while installing the camera.

4. Install the camera body in the reverse order of “Disassembling”.

5. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for the camera” section. (page 31)

6. Close the dome cover.

`To ensure waterproofing, tight up the fixing bolts using the

L-wrench and drill bit.

Outdoor installation

When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside.

1. Connect the power, I/O, BNC, and LAN cables.

2. Wrap the black cable jacket (Area A) and the cable connection area with waterproof (butyl rubber) tape so that more than half of the butyl rubber tape is overlapped.

If the cable jacket is not waterproofed properly,

then it can directly cause leakage. Make sure to protect the cable with a dense layer of taping.

Waterproof butyl tape is made of butyl rubber that can be stretched to twice its normal length.

Camera

System

28_ installation & connection

Page 29

Optional Accessories for Installation

For your easier installation, you can purchase appropriate optional accessories available.

1. WALL MOUNT ADAPTOR(SBP-300WM or

SBP-300WM1)/HANGING MOUNT (SBP-300HM6) This adaptor is used when installing the dome camera onto a wall.

2. CEILING MOUNT ADAPTOR(SBP-300CM)/

HANGING MOUNT(SBP-300HM6) This adaptor is used when installing the dome camera on a concrete ceiling.

● INSTALLATION & CONNECTION

English _29

Page 30

installation & connection

3. POLE MOUNT ADAPTOR(SBP-300PM) This is an adaptor for WALL MOUNT ADAPTOR (SBP-300WM or SBP-300WM1) installation on a pole whose diameter is bigger than 80mm.

4. CORNER MOUNT ADAPTOR (SBP-300KM) This is an adaptor for WALL MOUNT ADAPTOR (SBP-300WM or SBP-300WM1) installation on the corner of wall joint.

30_ installation & connection

Page 31

Adjusting the monitoring direction for the camera (SNV-8080)

Pan

VIDEO

RESET

AC 24V / DC 12V

+ -

● INSTALLATION & CONNECTION

Tilt

Lens rotation

`Adjusting the monitoring direction

You can adjust the camera direction only when the camera is fixed on the ceiling. Where, rotating the camera unit to the left or right is called Pan, adjusting the tilt is called Tilt, and turning the lens on its axis is called Rotation.

- The effective range of pan is a total of 354 degrees.

- The effective range of rotation is a total of 355 degrees.

- The effective range of tilt is a total of 67 degrees.

The image can be covered up by the camera case depending on the angle.

Do not forcefully turn the focus/zoom lens after the dome case is disassembled.

Otherwise, it may cause an incorrect focus due to a motor failure.

`Methods of adjustment

1. After installing the camera, adjust the panning angle in consideration of the

monitoring direction.

2. Set the horizontal angle so that the image is not reversed.

3. Adjust the tilt angle so that the camera faces toward the monitoring object.

English _31

Page 32

installation & connection

INSERTING/REMOVING A MICRO SD MEMORY CARD

Disconnect the power cable from the camera before inserting the Micro SD memory card.

Do not insert the Micro SD memory card while it’s upside down by force.

Otherwise, it may damage the Micro SD memory card.

Inserting a Micro SD Memory Card

Push the Micro SD memory card in the direction of the arrow shown in the diagram.

<SNB-8000>

32_ installation & connection

<SNV-8080>

Page 33

Removing a Micro SD Memory Card

Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot.

<SNB-8000>

<SNV-8080>

● INSTALLATION & CONNECTION

Pressing too hard on the Micro SD memory card can cause the card to shoot out uncontrollably

from the slot when released.

Before removing your Micro SD memory card, turn off the camera or go to <Storage>, turn the

device off, and press the [Apply (

If you turn off the camera or remove the Micro SD memory card that contains data from the

product, the data may be lost or damaged.

)] button. (Page 111)

English _33

Page 34

installation & connection

MEMORY CARD INFORMATION (NOT INCLUDED)

What is a memory card?

The memory card is an external data storage device that has been developed to offer an entirely new way to record and share video, audio, and text data using digital devices.

Selecting a memory card that’s suitable for you

Your camera supports Micro SD/SDHC/SDXC memory cards. You may, however, experience compatibility issues depending on the model and make of the memory card.

For your camera, we recommend you use a memory card from the following manufacturers: Micro SD/SDHC/SDXC Memory Card : Sandisk, Transcend

Memory cards of 4GB ~ 64GB is recommended for using with this camera.

Playback performance can be affected depending on the speed of memory card, so use the high-speed memory card.

For the framerate below 30 fps, it is recommended to use the specification memory card of Class 6 or higher.

For the framerate over 31 fps, it is recommended to use the specification memory card of Class 10 UHS or higher.

Memory Card Components

Contacts

Micro SD/SDHC/SDXC

34_ installation & connection

Page 35

CONNECTING WITH OTHER DEVICE

Ethernet

<SNB-8000>

● INSTALLATION & CONNECTION

Monitor to install

Grounding cable

Power

English _35

Page 36

installation & connection

+ -

AC 24V / DC 12V

RESET

VIDEO

Monitor to install

Ethernet

Power

The CVBS out terminal of the product is provided for easier installation, and is not recommended

for monitoring purposes.

36_ installation & connection

CAUTION: Be ware o f the Rated Voltage and Polari ty of the power conn ection .

<SNV-8080>

Page 37

Ethernet Connection

Connect the Ethernet cable to the local network or to the Internet.

Power Supply (SNB-8000)

Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the camera.

If you turn on PoE and DC12V and AC24V at the same time, the first applied one will be used as

the power source.

- You can also use a router featuring PoE to supply power to the camera.

- Use PoE that is compliant with the IEEE802.3af protocols.

Be careful not to reverse the polarity when you connect the power cable.

AC24V can be connected in non-polar union.

If you want to connect an external device, you must turn off the external device before proceeding.

Power Supply (SNV-8080)

Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the camera.

If you turn on PoE and DC12V and AC24V at the same time, the first applied one will be used as

the power source.

- You can also use a router featuring PoE to supply power to the camera.

- Use PoE that is compliant with the IEEE 802.3af protocols.

The heater operates at a low temperature environment in all cases that the dome camera is

operated by PoE, AC 24V or DC 12V.

- Install the product at the temperature of -35°C or higher.

- The product can be operated down to the temperature of -40°C after it started up.

Be careful not to reverse the polarity when you connect the power cable.

AC 24V can be connected in non-polar union.

If you want to connect an external device, you must turn off the external device before proceeding.

● INSTALLATION & CONNECTION

English _37

Page 38

installation & connection

Power Cable Specification for Each Model

In case of DC 12V Input:

Wire Type (AWG) #22 #20 #18

Cable Length (Max.)

In case of AC 24V Input:

Wire Type (AWG) #22 #20 #18

Cable Length (Max.)

Network Cable Specification

Item Contents Remark

Connector RJ45

Ethernet 10/100Base-T 10/100 Mbps

Cable UTP Category 5e

Max Distance 100M

PoE Support IEEE 802.3af

Grounding the Product (SNB-8000)

Connect the ground wire to the ground terminal which is located above the power input terminal by using a screwdriver.

Grounding protects the product from a surge or lightning.

When grounding, make sure to turn the product’s power off.

SNB-8000 20m 32m 50m

SNV-8080 24m 38m 60m

SNB-8000

SNV-8080

34m 55m 88m

Recommended Grounding Cable

• Length : Less than 3M

• Gauge : 18 AWG or bigger Ex) UL1007 AWG 18/16, UL1015 AWG18/16/14/12, UL2468 AWG18/16/14

38_ installation & connection

Page 39

Connecting to Audio Input/Output

Microphone Amp

Speaker

Microphone

● INSTALLATION & CONNECTION

Microphone

Speaker

AmpSpeaker

Speaker

Network

Speaker

Amp Amp

Microphone

English _39

Page 40

installation & connection

1. Connect the AUDIO IN port of the camera with the microphone or LINE OUT port of

the amplifier that the microphone is connected to.

As a microphone is built in, you can use the built-in microphone instead of an external one.

(It is applicable only to the SNB-8000 model.)

2. Connect the AUDIO OUT port of the camera with the speaker or LINE IN port of the

amplifier that the speaker is connected to.

3. Check the specifications for audio input.

• Audio Codec

- Audio In : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz), G.726 ADPCM (Bit Rate: 16Kbps, 24Kbps, 32Kbps, 40Kbps / Sampling Frequency: 8kHz)

- Audio Out : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz)

• Full duplex Audio

• Audio in : Mono signal line input (Max.2.4 Vpp)

• Audio out : Mono signal line output (Max.2.4 Vpp)

• Line out impedance : 600Ω

Connecting to the I/O port box (SNB-8000)

Connect the Alarm I/O signal to the corresponding port of the rear port box.

• ALARM IN : Used to connect the alarm input sensor or external day/night sensor.

• ALARM OUT : Used to connect the alarm output signal.

• GND : Used for earth-grounding.

• RS-485+ : Communication port for RS-485 receiver (+).

• RS-485- : Communication port for RS-485 receiver (–).

40_ installation & connection

Page 41

Connecting an external RS-485 device (SNB-8000)

Connect the camera with an external device using the [RS-485 +, -] ports. You can control the pan/tilt operations of the camera via RS-485 communications.

The GND connection is recommended for RS-485 communications. If you encounter a communication

failure, connect the GND pin as appropriate to correct the GND level between camera and external device.

Connecting to the I/O port box (SNV-8080)

Connect the Alarm I/O cable to the corresponding port of the inner port box.

Alarm

Sensor

(Warning lamp)

• ALARM OUT : Used to connect the alarm output signal.

• ALARM IN : Used to connect the alarm input sensor or external day/night sensor.

• GND : Common terminal to connect alarm signals.

● INSTALLATION & CONNECTION

English _41

Page 42

installation & connection

To connect the external sensor

Connect one strand of each signal line (2-strand) of the sensors to the [ALARM IN] port, and connect the other strand to the [GND] port.

Alarm In Wiring Diagram

External

connection

Sensor

To connect the alarm out

If devices (e.g., flashing light and siren) that exceed the voltage and current specifications are connected by using the open collector method, it may cause malfunction.

Refer to the alarm out connection diagram below when connecting devices that exceed the voltage and current specifications.

Alarm Out Wiring Diagram

Inside of the camera

GND

VCC_3.3V

RESISTOR RESISTOR

RESISTORALARM IN (5mA SINK)

TRANSISTOR

MLCC

GND

DIODE

External connection Inside of the camera

RESISTOR RESISTOR

DIODE

COM

Warning

lamp / Siren

Warning lamp / Siren power GND

COM

RELAY

42_ installation & connection

DC 5V or 3.3V

10K ohm

TRANSISTOR

ALARM OUT(12VDC 20mA MAX)

RESISTOR

TRANSISTOR

GND

Page 43

network connection and setup

AC 24V / DC 12V

RESET

VIDEO

+ -

You can set up the network settings according to your network configurations.

CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING

Connecting to the camera from a local PC in the LAN

1. Launch an Internet browser on the local PC.

2. Enter the IP address of the camera in the address bar of the browser.

Camera

VIDEO

RESET

AC 24V / DC 12V

Mircro SD

Camera

+ -

INTERNET

External Remote PC

●

NETWORK CONNECTION AND SETUP

Local PC

DDNS Server (Data Center, KOREA)

A remote PC in an external Internet out of the LAN network may not be able to connect to the

camera installed in the intranet if the port-forwarding is not properly set or a firewall is set. In this case, to resolve the problem, contact your network administrator.

In the IP installer, you can use the initial password, “4321” to set IP Address, Subnet Mask,

Gateway, HTTP Port, Device Port, IP type. After changing the network interface, for better security, access the web viewer and change the password.

By factory default, the IP address will be assigned from the DHCP server automatically.

If there is no DHCP server available, the IP address will be set to 192.168.1.100. To change the IP address, use the IP Installer. For further details on IP Installer use, refer to “Static IP Setup”. (Page 48)

English _43

Page 44

network connection and setup

CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE MODEM

Camera

1. Connect the user PC directly with the network camera.

2. Run the IP Installer and change the IP address of the camera so that you can use

the web browser on your desktop to connect to the Internet.

3. Use the Internet browser to connect to the web viewer.

4. Move to [Setup] page.

5. Move to [Network] – [DDNS] and configure the DDNS settings.

6. Move to [Basic] – [IP & Port], and set the network type to [DHCP].

7. Connect the camera, which was removed from your PC, directly to the modem.

8. Restart the camera.

For registering the DDNS settings, refer to “Registering with DDNS”. (page 102)

For configuring the DDNS settings, refer to “DDNS”. (page 101)

For setting the network type, refer to “IP & Port”. (page 80)

DSL/Cable Modem

INTERNET

DDNS Server (Data Center, KOREA)

External Remote PC

44_ network connection and setup

Page 45

CONNECTING THE CAMERA DIRECTLY TO A PPPoE MODEM

Camera

1. Connect the user PC directly with the network camera.

2. Run the IP Installer and change the IP address of the camera so that you can use

the web browser on your desktop to connect to the Internet.

3. Use the Internet browser to connect to the web viewer.

4. Move to [Setup] page.

5. Move to [Network] – [DDNS] and configure the DDNS settings.

6. Move to [Basic] – [IP & Port] Setup Page, set the network type to [PPPoE], and

enter the network service’s ID and password.

7. Connect the camera, which was removed from your PC, directly to the modem.

8. Restart the camera.

For registering the DDNS settings, refer to “Registering with DDNS”. (page 102)

For configuring the DDNS settings, refer to “DDNS”. (page 101)

For setting the network type, refer to “IP & Port”. (page 80)

PPPoE Modem

INTERNET

DDNS Server (Data Center, KOREA)

External Remote PC

●

NETWORK CONNECTION AND SETUP

English _45

Page 46

network connection and setup

AC 24V / DC 12V

RESET

VIDEO

+ -

CONNECTING THE CAMERA TO A BROADBAND ROUTER WITH THE PPPoE/CABLE MODEM

This is for a small network environment such as homes, SOHO and ordinary shops.

Camera

VIDEO

RESET

AC 24V / DC 12V

+ -

Mircro SD

Camera

Local PC

Configuring the network settings of the local PC connected to a Broadband Router

Configuring the network settings of the local PC connected to a Broadband Router, follow the instructions below.

• Select : <Network>  <Properties>  <Local Area Connection>  <General> <Properties>  <Internet Protocol (TCP/IP)>  <Properties>  <Obtain an



IP address automatically> or <Use the following IP address>.

• Follow the instructions below if you select <Use the following IP address>:

ex1) If the address (LAN IP) of the Broadband Router is 192.168.1.1

IP address : 192.168.1.100 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.1.1

ex2) If the address (LAN IP) of the Broadband Router is 192.168.0.1

IP address : 192.168.0.100 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.0.1

ex3) If the address (LAN IP) of the Broadband Router is 192.168.xxx.1

IP address : 192.168.xxx.100 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.xxx.1

For the address of the Broadband Router, refer to the product’s documentation.

For more information about port forwarding of the broadband router, refer to "Port Range

46_ network connection and setup

Forward (Port Mapping) Setup”. (Page 53)

Broadband

Router

PPPoE or

Cable Modem

INTERNET

PPPoE or

Cable Modem

DDNS Server (Data Center, KOREA)

External Remote PC

Page 47

BUTTONS USED IN IP INSTALLER

a b c d e f g

●

NETWORK CONNECTION AND SETUP

h i

Item Description

Device Name

Alias This function is not currently implemented.

Mode

MAC(Ethernet)

Address

IP Address

Protocol

Model name of the connected camera. Click the column to sort the list by model name. However, search will be stopped if clicked during the search.

Displays either <Static>, <Dynamic> or <PPPoE> for the current network connection status.

Ethernet address for the connected camera. Click the column to sort the list by Ethernet address. However, search will be stopped if clicked during the search.

IP address. Click the column to sort the list by IP address. However, search will be stopped if clicked during the search.

Network setting for the camera. The factory default is “IPv4”. Cameras with the IPv6 setting will be displayed “IPv6”.

j k l m

English _47

Page 48

network connection and setup

Item Description

URL

IPv4 Scans for cameras with the IPv4 setting.

IPv6

Auto Set The IP Installer automatically configures the network settings.

Manual Set You should configure the network settings manually.

Exit Exits the IP Installer program.

For the IP installer, use only the installer version provided in the installation CD or use the latest one if

available. You can download the latest version from the Samsung web site (www.samsungcctv.com).

STATIC IP SETUP

Manual Network Setup

Run <IP Installer_v2.XX.exe> to display the camera search list. At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.

For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not

support this function.

1. Select a camera in the search list.

Check the MAC address of the camera on the camera’s label. Both the [Auto Set] and [Manual Set] buttons will be activated.

2. Click [Manual Set].

The Manual Setting dialog appears. <IP Address>, <Subnet Mask>, <Gateway>, <HTTP Port>, and <Device Port> of the camera are displayed in the preset values.

DDNS URL address enabling access from the external Internet. However, this will be replaced with the <IP Address> of the camera if DDNS registration has failed.

Scans for cameras with the IPv6 setting. Activated in an IPv6 compliant environment only.

Scans for cameras that are currently connected to the network. However, this button will be grayed out if neither IPv4 nor IPv6 is checked.

48_ network connection and setup

Page 49

3. In the <Address> pane, provide the

necessary information.

• MAC (Ethernet) Address : The MAC address imprinted on the camera label is automatically displayed and requires no user setting.

IP related parameters can be set only

when DHCP is not checked.

If not using a Broadband Router

For setting <IP Address>, <Subnet Mask>, and <Gateway>, contact your network administrator.

4. In the <Port> pane, provide necessary

information.

• HTTP Port : Used to access the camera using the Internet browser, defaulted to 80.

• Device Port : Used to control the video signal transfer, defaulted to

4520.

5. Enter the password. Enter the password of “admin” account, which was used to access the camera.

For the security purposes, you are recommended to use a combination of numbers, alphabets

uppercase and lowercase and special characters for your password.

If you want to change the password, refer to “Administrator password change” of the user

setup. (page 77)

6. Click [OK]. Manual network setup will be completed.

●

NETWORK CONNECTION AND SETUP

English _49

Page 50

network connection and setup

If using a Broadband Router

• IP Address : Enter an address falling in the IP range provided by the Broadband Router. ex) 192.168.1.2~254,

192.168.0.2~254,

192.168.XXX.2~254

• Subnet Mask : The <Subnet Mask> of the Broadband Router will be the <Subnet Mask> of the camera.

• Gateway : The <Local IP Address> of the Broadband Router will be the <Gateway> of the camera.

The settings may differ depending on the connected Broadband Router model.

For more information, refer to the user manual of the applicable router.

For more information about port forwarding of the broadband router, refer to “Port Range

Forward (Port Mapping) Setup”. (Page 53)

If the Broadband Router has more than one camera connected

Configure the IP related settings and the Port related settings distinctly with each other.

ex)

Category Camera #1 Camera #2

IP related settings

Port related settings

If the <HTTP Port> is set other than 80, you must provide the <Port> number in the address bar

of the Internet browser before you can access the camera. ex) http://IP address : HTTP Port

50_ network connection and setup

IP Address Subnet Mask Gateway

HTTP Port Device Port

http://192.168.1.100:8080

192.168.1.100

255.255.255.0

192.168.1.1

8080 4520

192.168.1.101

255.255.255.0

192.168.1.1

8081 4521

Page 51

Auto Network Setup

Run <IP Installer_v2.XX.exe> to display the camera search list. At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.

For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not

support this function.

1. Select a camera in the search list.

Check the MAC address of the camera on the camera’s label. Both the [Auto Set] and [Manual Set] buttons will be activated.

2. Click [Auto Set].

The Auto Setting dialog appears. The <IP Address>, <Subnet Mask>, and <Gateway> will be set automatically.

3. Enter the password. Enter the password of “admin” account, which was used to access the camera.

For the security purposes, you are

recommended to use a combination of numbers, alphabets uppercase and lowercase and special characters for your password.

If you want to change the password, refer

to “Administrator password change” of the user setup. (page 77)

4. Click [OK]. Auto network setup will be completed.

●

NETWORK CONNECTION AND SETUP

English _51

Page 52

network connection and setup

DYNAMIC IP SETUP

Dynamic IP Environment Setup

• Example of the Dynamic IP environment

- If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server

- If connecting the camera directly to modem using the DHCP protocols

- If IPs are assigned by the internal DHCP server via the LAN

Checking the Dynamic IP

1. Run the IP Installer on the user’s local

computer. Cameras allocated with <Dynamic IP> address are shown in the list.

2. Select a camera from the search result.

3. Click the [Manual Set] button and

check the camera’s <Dynamic IP> address. If you uncheck <DHCP>, you can change IP to <Static>.

52_ network connection and setup

Page 53

PORT RANGE FORWARD (PORT MAPPING) SETUP

If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the Broadband Router so that a remote PC can access the camera in it.

Manual Port Range Forwarding

1. From the Setup menu of the Broadband Router, select <Applications & Gaming> - <Port Range Forward>.

For setting the port range forward for a third-party Broadband Router, refer to the user guide of that Broadband Router.

2. Select <TCP> and <UDP Port> for each connected camera to the Broadband Router. Each port number for the Broadband Router should match that specified in <Setup> - <Basic> - <IP & Port> from the camera’s web viewer menu.

3. When done, click [Save Settings]. Your settings will be saved.

Above sample instructions are based on the CISCO’s Broadband Router.

The settings may differ depending on the connected Broadband Router model.

For more information, refer to the user manual of the applicable router.

●

NETWORK CONNECTION AND SETUP

English _53

Page 54

network connection and setup

Setting up Port Range Forward for several network cameras

• You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page.

• A user can change each port using the camera setting screen.

When Camera1 and Camera2 are connected to a router :

User

Start End Protocol IP Address 3000 3000 TCP/UDP 192.168.1.100 3001 3001 TCP/UDP 192.168.1.101 4520 4520 TCP/UDP 192.168.1.100 4521 4521 TCP/UDP 192.168.1.101 8080 8080 TCP/UDP 192.168.1.100 8081 8081 TCP/UDP 192.168.1.101



Broadband Router

Port forwarding can be done without additional router setup if the router supports the UPnP (Universal Plug and Play) function. After connecting the network camera, set <Quick connect> of <Samsung DDNS> to <On> in the “Setup  Network  DDNS” menu.

Internet





Camera1 (192.168.1.100)

HTTP port 8080

Device port 4520

RTSP port 3000

Camera2 (192.168.1.101)

HTTP port 8081

Device port 4521

RTSP port 3001

54_ network connection and setup

Page 55

CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC

1. Run the IP Installer.

It will scan for connected cameras and display them as a list.

2. Double-click a camera to access.

The Internet browser starts and connects to the camera.

Access to the camera can also be gained by typing the camera's IP address in the address bar of

the Internet browser.

CONNECTING TO THE CAMERA FROM A REMOTE PC VIA THE INTERNET

Since using the IP Installer on a remote computer that is not in the Broadband Router’s network cluster is not allowed, users can access cameras within a Broadband Router’s network by using the camera’s DDNS URL.

1. Before you can access a camera in the Broadband Router network, you should have

set the port range forward for the Broadband Router.

2. From the remote PC, launch the Internet browser and type the DDNS URL address

of the camera, or the IP address of the Broadband Router in the address bar. ex) http://www.samsungipolis.com/Product ID

For registering the DDNS settings, refer to “Registering with DDNS”. (page 102)

●

NETWORK CONNECTION AND SETUP

English _55

Page 56

web viewerweb viewer

CONNECTING TO THE CAMERA

Normally, you would

1. Launch the Internet browser.

2. Type the IP address of the camera in

the address bar. ex) • IP address (IPv4) : 192.168.1.100

http://192.168.1.100



- the Login dialog should appear. IP address (IPv6) : 2001:230:abcd:

•

ffff:0000:0000:ffff:1111

http://[2001:230:abcd:ffff:0000



:0000:ffff:1111] - the Login dialog should appear.

If the HTTP port is other than 80

1. Launch the Internet browser.

2. Type the IP address and HTTP port number of the camera in the address bar.

ex) IP address : 192.168.1.100:HTTP Port number(8080)

http://192.168.1.100:8080 - the Login dialog should appear.



Using URL

1. Launch the Internet browser.

2. Type the DDNS URL of the camera in the address bar.

ex) URL address : http://www.samsungipolis.com/Product ID

- the Login dialog should appear.

Network connection is disabled in the LAN only environment.

56_ web viewer

Page 57

Connecting via UPnP

1. Run the client or operating system in support of the UPnP protocol.

2. Click the camera name for search.

In the Windows operating system, click the camera name searched from the network menu.

- The login window is displayed.

Connecting via Bonjour

1. Run the client or operating system in support of the Bonjour protocol.

2. Click the camera name for search.

In the Mac operating system, click the camera name searched from the Bonjour tab of Safari.

- The login window is displayed.

To check the DDNS address

If the camera is connected directly to the DHCP cable modem, DSL modem, or PPPoE modem, the IP address of your network will be changed each time you try to connect to the ISP (Internet Service Provider) server. If this is the case, you will not be informed of the IP address changed by DDNS.

Once you register a dynamic IP-based device with the DDNS server, you can easily check the changed IP when you try to access the device. To register your device to the <DDNS> server, visit www.samsungipolis.com and register your device first, and then set the Web Viewer’s <Network> - <DDNS> to <Samsung DDNS>, as well as providing <Product ID> that had been used for DDNS registration.

● WEB VIEWER

English _57

Page 58

web viewer

PASSWORD SETTING

When you access the product for the first time, you must register the login password. When the “Password change” window appears, enter the new password.

For a new password with 8 to 9 digits,

you must use at least 3 of the following: uppercase/lowercase letters, numbers and special characters. For a password with 10 to 15 digits, you must use at least 2 types of those mentioned.

Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].?/

For higher security, you are not recommended to repeat the same characters or consecutive

keyboard inputs for your passwords.

If you lost your password, you can press the [RESET] button to initialize the product. So, don’t lose

your password by using a memo pad or memorizing it.

Whenever you access the camera, the login window appears. Enter the User ID and password to access the camera.

1. Enter “admin” in the <User name>

input box. The administrator ID, “admin”, is fixed and can not be changed.

2. Enter the password in the <Password>

input field.

3. Click [OK].

If you have logged in successfully, you will the Live Viewer screen.

When you access the camera web viewer, pay special attention to the security by checking

whether the image data is encrypted.

If you check the “Remember my credentials” option when your input is done, in future you will

be logged in automatically without being prompted to enter the login information.

You will experience the best video quality if the screen size is 100%. Reducing the ratio may cut

the image on the borders.

58_ web viewer

Page 59

INSTALLING STW WebViewer PLUGIN

If connecting to a camera for the first time, you will see the installation message. Then, install the required WebViewer Plugin to access the camera and control the video from it in real time.

1. When the monitoring page is accessed

for the very first time, the installation page is displayed. Click [Click Here] to begin installation.

If the plug-in installation file download status is suspended at 99% in the Internet Explorer

browser, retry it after selecting “Release SmartScreen filter” in “Tool  SmartScreen filter”.

2. Click [Run] in the message window.

3. Click [Yes] when the notice window

saying that all browser windows will be closed.

4. When the old version of the Web Viewer

Plug-in is installed, a notice window saying the old version will be deleted is displayed. Click [Yes] when the notice window is displayed.

Steps 4 and 5 will be skipped if no Web Viewer Plug-in is installed.

● WEB VIEWER

English _59

Page 60

web viewer

5. Click [OK].

The old version of Web Viewer Plug-in is deleted.

6. Click [Install] to begin installation of the

Web Viewer Plug-in.

7. Click [Finish].

STW Web Viewer Plug-in installation is completed.

In your internet explorer, if you need

to move to the installation screen after installing the STW webviewer plugin, check whether webviewer_ activexplugin_lib.control in the “Tool  Additional Function Management” menu is “Activated”. If not, and if there is a persisting problem, then select “Tools  Internet Options  General” and delete all the search records.

60_ web viewer

Page 61

USING THE LIVE SCREEN

a b c d e

f g h i j k l

Item Description

Monitoring Move to the monitoring screen.

Playback

Setup Move to the Setup screen.

Profile access

information

Viewer Screen

Profile type

Screen

Optimization

Move to the screen where you can search for the video recording saved in your Micro SD memory card or NAS.

You can read the profile information.

Displays the Live video on the screen.

You can use the mouse wheel to activate the digital zooming in Viewer screen.

You can select a profile type in <Video profile> under the <Basic> setup menu.

When the Web Viewer is connected, the profile information currently using is

displayed.

The video size of the camera will switch to as big as the Web browser.

● WEB VIEWER

English _61

Page 62

web viewer

Item Description

Fix the resolution

Full Screen Switch the current video to the maximum size of the monitor.

Capture Saves the snapshot as an image file in the .jpg format.

Manual recording

Audio/Microphone

Control

Alarm output Activate the Alarm Out port.

External PTZ

Hide the context

Regardless of the resolution setup configured in the camera, it sets the resolution to 640x480. Press it again to switch back to the default resolution.

Users can save their video in the micro SD memory card or NAS on their own.

To take video manually, change the recording setting first. Refer to “Storage” for

how to set recording (page 111).

Enable Audio and Microphone are control the Audio volume.

Only the Audio volume can be controlled.

Connect the external PTZ to the RS-485 terminal and control the PTZ camera lens direction with the arrow keys.

Only for SNB-8000.

The pan/tilt operations will be enabled only if the camera is connected to a pan/

tilt-compliant receiver.

The left-corner context menu will disappear but only the menu icon.

62_ web viewer

Page 63

To capture the snapshot

1. Click [Capture ( )] on the scene to capture.

2. When a captured video is saved, a notification message appears.

When using Internet Explorer, the captured video is saved in My Computer / My Documents / Pictures. In Mac OS, it is saved in “~/Pictures” or “/Users/{user account}/Pictures/”.

If you encounter an interrupted video when capturing the image with IE8 on a Windows 7-based

PC, deselect “Turn On Protected Mode” from “Tools – Internet Options – Security”.

If the screen is not captured by IE browser in Windows 7 or 8, run the IE Browser with the Admin

privilege.

How to record videos manually

1. Press [Manual recording ( )].

2. To end the recording, press [Manual recording (

After inserting the SD card, go to <Event> - <Storage> and turn on the SD card by selecting “On”

or turn on NAS by selecting “On” after connecting to it. Then you can use the manual recording function.

)] again.

To fit the full screen

1. Click the [Full Screen (

2. This will fit the Viewer to the full screen.

3. To exit the full screen mode, press [Esc] on the keyboard.

For the Internet Explorer and Google Chrome browser, you can switch to the full screen.

)] button.

● WEB VIEWER

English _63

Page 64

web viewer

To Use Audio

1. Click [Audio ( )] icon to activate audio communication.

2. Use [

To Use Microphone

Click [Mic ( )] icon to activate the microphone.

To control the PTZ

1. Press the [PTZ ( )] tab.

2. Adjust the direction of the camera

To run a sequence

• : Run a saved preset.

•

] bar to control the volume.

If there is no sound from pulling in and out the audio jack while it is in operation, click the

[Audio (

by controlling the cursor [ screen moving pad, or control the zoom or focus.

For further details on PTZ use, refer to

“DPTZ setup”. (page 82)

: Run a saved group.

Refer to “To set a group” for details of group setting. (page 84)

: Run a saved home position.

Refer to “To add the home position” for details of home position setting. (page 83)

Configure preset and group in <DPTZ setting> to enable sequence function.

)] icon to enable it again.

] of the

64_ web viewer

Page 65

PLAYING THE RECORDED VIDEO

Before you can play the video, you must configure the record settings. For details on record settings,

refer to “Storage”. (page 111)

Name of event search screen and its function

b c

Item Description

Search range setting

Search event setting Set the event type to search within the search period.

Set the search date and time range for data saved in your Micro SD memory card or NAS.

● WEB VIEWER

Event search Run the event search.

English _65

Page 66

web viewer

To play the content after searching by event

1. Click the [Playback ( )] button.

2. Specify the start time and end time of

your search.

3. Select an event type for your search

within the specified period.

4. Click the [Event search] button.

The search results will be displayed in the list.

If more than 800 events are recorded

within the search period, your search will be limited up to the date when the 800th event is recorded. For instance, if the search period is between 10th and 15th day of the month, and more than 800 events were recorded 10th through 11th, your search will be limited up to 11th day with a total of 800 events, and events after then (from 12th) will not be found.

5. Select a data item to play in the search

list.

6. Click the [Play (

7. To stop playing the video, click [Stop (

8. To return to the search screen, click [Exit (

)] button.

)].

66_ web viewer

Page 67

Name of time search screen and its function

c d e

f g h i

Item Description

Time bar The section in the specific period is played by moving the time bar.

Search date setting

Speaker

Screen optimization The camera image is converted to fit the Web browser window.

Fix the resolution

Capture The current image is saved as a .jpg image file.

Set the search date using the calendar.

If there is data saved in your Micro SD memory card or NAS on the

day, it is marked as a box on the calendar.

To listen to a voice signal (if present) in the recorded video, then activate the voice signal icon when you play it.

Regardless of the resolution setup configured in the camera, it sets the resolution to 800x600. Press it again to switch back to the default resolution.

● WEB VIEWER

Full screen The current image is converted to cover the maximum size of the monitor.

English _67

Page 68

web viewer

Item Description

Video information Time data of the replayed video is displayed on the screen.

Set the desired date to make a backup copy of video data saved in your

Backup

To play after searching by time

1. Click [Time Search ( )].

2. Click a desired date in the calendar.

The video on the specified date will be played.

3. If the video playback is stopped, select a time and click [Play ( The video on the selected time will be played.

4. While the video is being played, the recording time for the current video will be shown.

5. Search for the video forward or backward, and control the play speed.

- How to Control the Play Interval : Select this button to move 1 frame forward. : Select this button to move 1 second back.

- To control the play speed

If selecting ), the button will switch to x1, x2, x4, x8, and the play speed will increase accordingly. When the ( button is selected, the playing speed is decreased to -1x, -2x, -4x, -8x and the playing speed slows down gradually. Subsequently the quick playing speed is returned to the normal speed and the reverse playing speed increases.

- To control the playback direction

If you see the ) button with the play speed displayed, the video will be played forward; Whereas, if you see the ( button with the play speed displayed, the video will be played backward.

- How to set the time bar

If you press the If you press the can be selected more easily.

Micro SD memory card or NAS.

Can be set as up to 5 minutes.

)].

button, the details of the time bar section can be viewed. button, you can view a wider range of times and the desired time

68_ web viewer

Page 69

6. Move [Time bar (

The time containing a normal recoding file will be highlighted in blue; the time with the event recording will be highlighted in red.

)] to a desired time point of the video before playing it.

To back up the searched video

1. During playback, click [ ] on the

scene to back up. The scheduling window for backup start and end time appears.

2. Click [

The Save As window appears.

3. Confirm the save path and click [Save]

button. The screenshot will be backed up to the specified path.

] button.

To play the backup video

The backed up images are saved in an .avi format. Gom Player, VLC Player, and Window Media Player are recommended as the media player compatible with this format.

In case of Windows Media Player, download the latest codec from www.windows7codecs.com

and install it prior to use.

● WEB VIEWER

English _69

Page 70

web viewer

To Play an AVI File

(1) Micro SD memory card

1. Separate the Micro SD memory card from the camera.

Before separating the Micro SD memory card, set the <Device> to <Off> in the “Setup 

Event  Storage” menu.

2. Insert the Micro SD memory card into the PC.

3. Play the AVI file in the “\ch00\img\ YYYY_mm_DD\AVI” directory, using a

media player.

A filename starts with the format “001_

YYYYMMDD_HHMMSS.avi” and the file number is incremented by one. YYYYMMDD_HHMMSS indicates the start time of data saving.

“001_YYYYMMDD_HHMMSS.smi” file

is a caption file, and you can view it if it exists in the same directory as its related AVI file.

The max recording time per AVI file is 5

minutes.

Once corrupted, the data in the Micro SD memory card cannot be replayed in the Web Viewer’s

[Playback].

70_ web viewer

Page 71

(2) NAS (Network-Attached Storage)

1. In Windows browser, use \\<ip

address>\ to access. ex)\\192.168.20.31\defaultfolder\ch01\ img\2013_07_02\AVI

2. Go to <Computer>  <Network drive

connection>  Enter 1.

3. Connected to the NAS.

The directory structure is same as the directory structure for a Micro SD memory card.

A filename starts with the format “001_

YYYYMMDD_HHMMSS.avi” and the file number is incremented by one. YYYYMMDD_HHMMSS indicates the start time of data saving.

“001_YYYYMMDD_HHMMSS.smi” file is a caption file, and you can view it if it exists in the

same directory as its related AVI file.

The max recording time per AVI file is 30 minutes.

If you change or damage the saved data on your own, it will not play back or save properly.

● WEB VIEWER

English _71

Page 72

setup screen

SETUP

On the network, you can set up basic information on the camera, video and audio, network events and system.

)

(

]

1. In the Live screen, click [Setup

2. The Setup screen appears.

The setting page for preview video requires the STW web viewer plug-in to be installed on the PC.

If it is not intalled properly, the installation page automatically apprears.

BASIC SETUP

Video profile

1. From the Setup menu, select the <Basic ( )> tab.

2. Click <Video profile>.

3. Set the <Megapixel Mode>.

Changing the mode selection displays a confirmation message regarding the resetting the video configurations. Click [OK] to confirm the changing video settings. The items below in 2MB and 5MB modes are independently saved. (Video & Audio : video setting / audio setting / camera setting / focus adjustment, Event : tampering detection / motion detection / audio detection. (Motion and motion time settings will not be changed.))

72_ setup screen

Page 73

4. Configure <PTZ Mode>.

PTZ mode can be activated by selecting it while the camera is in 5m mode and outside. When connecting to the camera from external NVR, ISV, our SmartViewer, and if the PTZ control command is sent from them, the PTZ mode the administrator already selected will be the one used for operation. When DPTZ mode was selected, DPTZ is active in a profile set to DPTZ only.

5. Set the <Video profile connection policy>.

• Keep connection when profile setting is changed : Changing profile properties that is used by existing connection does not affect such connection and remains with old profile setup. If not selected, changing a profile used by an existing connection resets such connection.

6. Select each profile properties. For more details, refer to “To Add/Change the Video Profile”. (Page 75)

7. Click the input box of each item and enter / select a desired value.

The context menu may differ depending on the selected codec type.

• Default profile : If no profile is selected when using the Web Viewer, the default video profile is applied.

• E-mail/FTP profile : Video profile to be transferred to the specified email or FTP site.

Only the MJPEG codec can be set as the E-mail/FTP profile.

• Record profile : This is the profile that is applied to video recording.

• DPTZ : If you select a profile to DPTZ in 5m mode, the profile operable for DPTZ is selected in the DPTZ check box and the screen area can be adjustable.

• Audio-In : Sets whether to use audio for video recordings.

● SETUP SCREEN

English _73

Page 74

setup screen

8. According to your situation, set ATC (Auto Transmit Control) mode.

• ATC mode : It adjusts the video properties according to the variance in the network bandwidth, controlling the bit rate. Adjusting the bit rate depends on the ATC mode.

- Control framerate : Reduce the frame rate if the network bandwidth drops down.

- Control compression : Control the compression rate if the network bandwidth drops down. Compression adjustment can cause deterioration of the image quality.

If <Bitrate control> is set to <CBR>, the encoding priority according to the ATC mode will be

fixed as below:

Bitrate control / ATC mode Control framerate Control compression

CBR Framerate Compression

• ATC sensitivity : Affect the transfer rate according to the variance in the network bandwidth. The transfer rate will be adjusted to the fastest if the bandwidth is <Very high>, and adjusted to the latest if the bandwidth is <Very low>.

• ATC limit : If the quality or frame rate is adjusted, the property will be changed to the applied value (%) against the previous setting value (100%). Note that if you reduce the property value too much, you may encounter flickering on the screen. So it is advisable to adjust the value within the threshold.

It is recommended to apply ATC control only for cameras supporting ATC.

Set the ATC sensitivity to <Very low> in a network environment with high variance in the network

bandwidth. If the network connection is unstable, you may encounter flickering on the screen.

9. When done, click [Apply (

)].

74_ setup screen

Page 75

To Add/Change the Video Profile

The profile setup can be added or modified to accommodate various profiles depending on the recording conditions.

1. Select one from the <Video profile> options.

2. Provide the name and select a codec.

3. Specify the conditions under which the codec will be applied.

4. Specify the details of the selected codec including resolution and frame rate.

Click <Advanced> to display the context menu.

• Resolution : Set the video size of the H.264 and MJPEG files.

• Framerate : Set the max number of video frames per sec.

• Maximum bitrate : Set the max bit rate of video when the bit rate control is set to VBR.

As the bit rate can be adjusted limitedly according to the resolution, frame rate and screen

complexity, the actual bit rate can be greater than the maximum bit rate. So you must consider the use conditions when setting the value.

• Target bitrate : Set the target bit rate when the bit rate control is set to CBR.

• Bitrate control : You can select one from constant bit rate and variable bit rate for compression. Fixed bitrate means that the network transmission bitrate is fixed while varying the video quality or frame rate, variable bitrate means that a higher priority is placed on the video quality while varying the bitrate.

After setting the fixed bit rate for bit control, if you select the video quality priority mode,

depending on the complexity of the screen, the actual transmitted frame rate may differ from the frame rate setup in order to guarantee the optimal video quality for the given bit rate.

• Encoding priority : You can set the priority of video transmission to frame rate or compression.

• GOV length : It specifies the distance (in terms of number of frames) between two consecutive I-Frames in a video sequence when H.264 codec was selected. (One I-Frame + 0~Several P-Frames)

● SETUP SCREEN

English _75

Page 76

setup screen

• Multicast(SVNP) : Specify the use of the SVNP protocol.

- IP address : Enter an IPv4 address with which you can connect to the IPv4 network.

- Port : Specify the video communication port.

- TTL : Set the TTL for the SVNP packet.

• Multicast(RTP) : Specify the use of the RTP protocol.

- IP address : Enter an IPv4 address with which you can connect to the IPv4 network.

- Port : Specify the video communication port.

- TTL : You can set the TTL for the RTP packet.

If you set the Multicast address to 224.0.0.0~224.0.0.255, multicast may not work properly

in all environments. In that case, we recommend you change the multicast address.

What is GOV length?

GOV(Group of Video object planes) is a set of video frames for H.264 compression, indicating a collection of frames from the initial I-Frame (key frame) to the next I-Frame. GOV consists of 2 kinds of frames: I-Frame and P-Frame.

I-Frame is the basic frame for the compression, also known as Key Frame, which contains one complete image data. P-Frame contains only the data that has changed from the preceding I-Frame.

For H.264 codec, you can determine the GOV length. If you set a recording profile with H.264 codec, the GOV length will be framerate/2.

76_ setup screen

Page 77

User

1. From the Setup menu, select the <Basic ( )> tab.

2. Click <User>.

3. Provide the necessary user information.

• Administrator password change : Change the password for the administrator.

For the security purposes, you are

recommended to use a combination of numbers, alphabets uppercase and lowercase and special characters for your password.

It is recommended to change your

password once every three months.

The password length and limits are shown as follows.

A combination of at least three types of upper case, lower case, numeric, and special

characters: 8 to 9 characters. A combination of at least two types of upper case, lower case, numeric, and special

characters: 10 to 15 characters. Should be different from the ID.

For higher security, you are not recommended to repeat the same characters or

consecutive keyboard inputs for your passwords. Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].?/

When you access the camera web page for the first time or access it after the initialization,

you will be moved to the admin password setting menu. In this menu, you need to login again with the new password before using the camera web

page menus.

● SETUP SCREEN

English _77

Page 78

setup screen

If the existing password is not matched, when you change the admin password, you

cannot change the password. After changing your password, if there is a camera connected to a CMS or NVR client,

then you need to re-register it with the newly changed password. If the camera is still connected with the same password, then the account may be locked because a client uses the previous password.

If you try to login with the registered account, 5 or more consecutive password authentication

has failed, and then the account may be locked for thirty seconds.

When the password is changed while multiple connections are active from a PC, the browser

may malfunction. In that case, reconnect to the server.

• Guest setup : If you select <Enable guest access>, the guest account can access

the Web viewer screen but can only view the live Viewer screen.

The ID/password for the guest account is <guest/guest>, which cannot be changed.

• Authentication setup : If you select <Enable RTSP connection without authentication>, you can access RTSP without logging in and view the video.

• Current users : If you select <Use>, you can set or change the user permissions.

The administrator can set the audio input, audio output, alarm output and PTZ control permissions.

Profile : If you select <Default>, you can only see the default profile video; if selecting <All>, you

can see the full profile videos.

ONVIF functions available to a registered user allowed to use ONVIF functions are limited to those

of granted with permission.

Video Transfer and Changing Video Information: Set the profile to <All>, and set Audio Input and

Audio Output.

Video Transfer, Changing Video Information, Alarm Output : Set the profile to <All>, and select at

your preference for the rest.

PTZ control : Select <PTZ>.

4. When done, click [Apply (

)].

78_ setup screen

Page 79

Date & Time

1. From the Setup menu, select the <Basic ( )> tab.

2. Click <Date & Time>.

3. Specify the time and date that will be

applied to the camera.

• Current system time : Displays the current time settings of your system.

• Timezone : Specify the local time zone based on the GMT.

• Use daylight saving time : If checked, the time will be set one hour before the local time zone for the specified time period. This option will be displayed only in areas where DST is applied.

• System time setup : Specify the time and date that will be applied to your system.

- Manual : Specify the time manually.

- Synchronize with NTP server : Sync with the time of the specified server address.

- Synchronize with PC viewer : Sets to the time of the computer connected.

4. When done, click [Apply (

If you select the <Synchronize with PC viewer>, the standard timezone should be set the same

as the current timezone in PC.

)].

● SETUP SCREEN

English _79

Page 80

setup screen

IP & Port

1. From the Setup menu, select the <Basic ( )> tab.

2. Click <IP & Port>.

3. Set the <IPv4 setup>.

• IP type : Select an IP connection type.

- Manual : Specify the IP address, Subnet mask, Gateway, DNS1, and DNS2.

- DHCP : Specify the DNS1 and DNS2.

- PPPoE : Specify the DNS1, DNS2, ID and Password.

If you set it to <Manual>, you should

specify the IP, Subnet mask, Gateway, DNS 1 & 2 manually.

• MAC address : Shows the MAC address.

• IP address : Displays the current IP address.

• Subnet mask : Displays the <Subnet mask> for the set IP.

• Gateway : Displays the <Gateway> for the set IP.

• DNS1/DNS2 : Displays the DNS(Domain Name Service) server address.

4. Set the <IPv6 setup>.

Set to <Use> to use IPv6 address.

• Default : Use the default IPv6 address.

• DHCP : Display and use the IPv6 address obtained from the DHCP server.

• Manual : Enter IP address and gateway manually and use it.

The IP addressing system will be defaulted to DHCP. If no DHCP server is found, the previous

settings will be restored automatically.

Once completed with editing, click [Apply ( )] to apply changes and the browser exits.

After a while, connect again with the changed IP.

80_ setup screen

Page 81

5. Type in each item in the Port menu as necessary.

Neither the port range between 0 and 1023 nor port 3702 is available.

• HTTP : HTTP port used to access the camera via the web browser. The default is 80(TCP).

Setting the HTTP port for Safari and Google Chrome browsers to 65535 is not allowed by security

policy.

• HTTPS : In this version, the security of the web communication protocol HTTP is strengthened. It can be used when you set HTTPS mode in SSL. The initial value is set to 443(TCP).

The available setting range is 1024~65535. (For security reasons, in your Safari or Google Chrome

browser, you may not use 65535 as your HTTPS port.)

• RTSP : Used to transfer videos in the RTSP mode; the default is 554.

• Use timeout : When connecting to RTSP, this function resets the connection if there’s no response for a certain time.

• Device port : Set a port used to transfer video signals with the Samsung protocols.

If changed the HTTP port, the browser exits.

Afterwards, address should contain the newly assigned HTTP port trailing the IP. ex) IP address: 192.168.1.100, HTTP port : Assigned 8080  http://192.168.1.100:8080 (If HTTP port is set to 80, no need to specify the port number)

Using RTSP and HTTPS is recommended in order to prevent the image information from being

restored.

6. When done, click [Apply (

)].

Event setup

You can easily set the event detection items, and move to the detailed setting.

1. From the Setup menu, select the <Basic (

2. Click <Event setup>.

3. Activate desired items on the Event list.

4. When done, click [Apply (

)> tab.

)].

● SETUP SCREEN

To make detailed event settings, click on

your desired settings. Go to detailed <Event> setting.

English _81

Page 82

setup screen

DPTZ setup

Use this settings page to move the camera view and perform the digital zoom.

1. Select the <Basic (

Setup menu.

2. Click <DPTZ setup>.

3. Click [▼ Show].

4. Click the cursor [

moving pad to control movement of the screen.

• Move screen: Scroll the cursor in the direction desired.

• Control screen movement rate: The farther the cursor is from the center of the screen, the faster the screen moves.

5. Control zoom movement.

• Zoom In: Move up the bar in the right of the UI, or press the [ The farther the bar is from the center, the faster the screen expands.

• Zoom Out: Move down the bar in the right of the UI, or press the [ button. The farther the bar is from the center, the faster the screen reduces in size.

When performing the sequence action

at a high or low temperature, the system may respond slower than the set rate for accurate sequence action.

)> tab from

] on the screen

] button.

]

82_ setup screen

Page 83

To add the home position

1. Move to a desired start screen point and press [ ].

The point will be set to the home position.

2. Click [

3. When the camera is rebooted after setting, the screen is located at the home

To add a preset

1. Select the preset number to add.

2. Set the name for the preset.

3. Press the [

To delete a preset

1. Select the preset number to delete.

2. Press the [

To move to a desired preset

1. Select a preset number that you want to move.

2. Press the [

] in the home position. You will move to the predetermined home position.

position. (If the camera was on another sequence operation, the sequence is performed.)

To activiate the Home position function, select Single Rectangle in the <Dewarping mode>.

] button.

● SETUP SCREEN

English _83

Page 84

setup screen

To set a group

The group function enables you to group various presets before calling them in sequence. Six groups can save a total of 128 presets each.

1. Select a group setting mode.

2. Press the [

Entered in the bottom list.

3. If you want to delete a preset added,

select it and press the [

4. Press the [

Saved in the bottom list.

5. Press the [

It performs the group operation.

6. Press the [

The running group will be stop.

7. Press the [

Selected group data will be deleted.

] button.

84_ setup screen

Page 85

VIDEO & AUDIO SETUP

Video setup

1. From the Setup menu, select the <Video & Audio ( )> tab.

2. Click <Video setup>.

3. Select a <Video source> mode.

• Flip mode : Turn upside down the image that is captured by the camera.

• Mirror mode : Flip horizontal the image that is captured by the camera.

4. Select Able or Disable for the analog

video output.

5. Select the video type.

6. Specify the privacy zone.

7. When done, click [Apply (

To set the privacy zone

You can specify a certain area of the camera video to be protected for your privacy.

1. Set it to <On>.

2. Select the color masking of desired

privacy area.

3. When done, click [Apply (

4. Click [▼ Show].

5. Place the cursor at a point in the video

and drag it to whatever you need.

6. Check if the area shown on the screen

matches with the target area, type the name, and click the [OK] button. If the displayed area does not match with the set area, click [Cancel] and reset the area.

7. If you want to delete a name in the list, select it and click [Delete (

)].

● SETUP SCREEN

English _85

Page 86

setup screen

Audio setup

You can configure the I/O settings of the audio source from the camera.

1. From the Setup menu, select the <Video & Audio (

2. Click <Audio setup>.

3. Set the audio input value.

• Source : Sets the audio input.

- Line : Connect the cable to the audio device.

- Internal microphone : Microphone that is built-in in the camera. (It is applicable only to the SNB-8000 model.)

- External microphone : 3.5 pi(¢) jack type external MIC.

• Apply power to Ext. Mic. : If the external microphone connected has no separate power supply, check this option to set camera to supply power to the connected external microphone. The option is enabled if <External microphone> is selected.

• Codec : Specify the audio codec.

- G.711 : A audio codec standard, it uses 64 Kbps PCM (Pulse Code Modulation) encoding. ITU standard audio codec that is adequate for digital voice transfer in PSTN network or through a PBX.

- G.726 : ITU standard audio codec applying ADPCM (Adaptive Differential Pulse Code Modulation) for variable bit rates of 40/32/24/16 Kbps to 64 Kbps PCM encoding.

• Bitrate : Set the bit rate to differentiate compression ratio if using G.726 codec.

• Gain : Specify the audio input amplification.

Sound quality deterioration or howling may occur if the loudness of the sound source or gain value

were set excessively.

4. Set the audio output level.

• Enable : Sets whether to use audio output.

• Gain : Specify the audio output amplification.

5. When done, click [Apply (

)> tab.

)].

86_ setup screen

Page 87

Camera setup

You can change the camera settings according to the environment where the camera is located.

1. From the Setup menu, select the <Video & Audio (

2. Click <Camera setup>.

Configure the settings as necessary of :

Sensor, SSDR, White balance, Back light, Exposure, Special, Day/Night, OSD

4. When done, click [Apply ( )].

If a certain time (timeout: 240s) is elapsed

your not pressing the [Apply ( button after changing the settings, your changes will not be applied.

To Set the Sensor

It specifies how many frames the camera CMOS sensor will capture per second.

1. Select <Sensor>.

2. Select <Mode>.

The sensor tab is only visible in 2MB mode. It can be set to 25fps or 30fps.

The sensor setting is not available in 5MB mode.

)> tab.

with

)]

● SETUP SCREEN

English _87

Page 88

setup screen

To Set SSDR (Samsung Super Dynamic Range)

In a scene where the difference between bright and dark is severe, you can increase the brightness of the dark area alone to regulate the overall brightness.

1. Select <SSDR>.

2. Set <Mode> to <On>.

3. Configure the <Level> and <D-Range>

settings as necessary.

• Level : Adjust the level of the dynamic range.

• D-Range : Select the amplitude area of the dynamic range.

To Set White Balance

You can correct the image colors based on white under any lighting conditions.

1. Select <White balance>.

2. Select <Mode>.

• ATW : Corrects the colors of the camera video automatically.

• Manual : You can adjust the red and blue gains of the camera video manually.

• AWC : Corrects the colors of the camera video to be optimized to the current lighting condition and screen mode. To obtain the optimal condition for the current lighting, put the focus of the camera to a white paper and press the [Set] button. If the lighting environment is changed, you should readjust the settings accordingly.

• Outdoor : Automatically corrects the video colors of the camera to be optimized to the outdoor environment.

• Indoor : Automatically corrects the video colors of the camera to be optimized to the indoor environment.

In AWC mode, click the [Set] button if you want to keep the white balance level of the current

image.

The white balancing may not work properly in the following conditions:

If this is the case, switch to AWC mode.

If the surrounding condition of the object is out of the temperature correction range

ex) Clear sky, sunset If the surrounding of the object is dark

If the focus of the camera directly faces the florescent lighting or if the camera is installed in a

place of variable illumination, the white balancing operation may be unstable.

88_ setup screen

Page 89

To Set BLC

You can specify a desired area on the video manually and set the area to be displayed more clearly.

1. Select <Back light>.

2. Set <Mode> to <BLC>.

3. Set <BLC level>.

You can change the level to adjust the brightness of the monitoring area.

4. Set the <Top, Bottom, Left, Right> levels to specify the target area.

When BLC is set, the green box is displayed on the screen for 15 seconds.

To prevent malfunction at the time of BLC setup, the vertical space of the BLC area should be over

40 and below 60 while the horizontal space over 30 and below 60.

To Set Exposure (SNB-8000)

You can adjust the exposure level of the camera.

1. Select <Exposure>.

2. Select each item and set it properly.

• Brightness : Adjust the screen brightness.

• Minimum shutter : The limit of the longest exposure time.

Shutter is the mode to set up the range of

the sensor exposure time which will specify the upper and lower limits for the electronic shutter movement.

The framerate may be reduced in the dark condition if Shutter has a lower value than specified in

the Sensor mode.

• Maximum shutter : The limit of the shortest exposure time.

• Anti flicker : It prevents screen flickering incurring from the dissonance between the surrounding lighting and the frequency.

● SETUP SCREEN

English _89

Page 90

setup screen

• SSNR : Select Able or Disable for the video noise elimination function.

• SSNR level : Adjust the noise reduction level.

• Lens : Select to set the lens mode of the camera to Manual or Auto.

- DC(Auto) : Select this if you use the DC lens. Only the iris is adjusted automatically, but the focus is not controlled automatically.

- Manual : Select this if you use a lens on which you adjust the iris and focus manually.

- P-Iris : It is selected to use the iris control lens equipped with a step motor. The current sensor for each MB mode supports the 4 types of P-Iris lens below. P-Iris lens supportable 5M Mode : LMVZ3510MIR 2M Mode : SLA-M3180PN/M13VP288IR/SLA-M2890PN

• P-Iris : Set up P-Iris.

- Auto : The iris is automatically adjusted to the amount of the surrounding light.

- Manual : Sets the iris manually to the desired position.

• P-Iris position : Set up the P-Iris position.

• AGC : Select AGC Control mode. Adjust the gain value of the video (that, in particular, was recorded at a low contrast scene and had a lower brightness level than normal) to control the video brightness.

The lens may malfunction if the <Lens> mode is not reset during lens assembly or disassembly.

The image exposure can be saturated depending on the Shutter setup range.

90_ setup screen

Page 91

To Set Exposure (SNV-8080)

You can adjust the exposure level of the camera.

1. Select <Exposure>.

2. Select each item and set it properly.

• Brightness : Adjust the screen brightness.

• Minimum shutter : The limit of the longest exposure time.

Shutter is the mode to set up the range of

the sensor exposure time which will specify the upper and lower limits for the electronic shutter movement.

The framerate may be reduced in the dark condition if Shutter has a lower value than specified in

the Sensor mode.

• Maximum shutter : The limit of the shortest exposure time.

• Anti flicker : It prevents screen flickering incurring from the dissonance between the surrounding lighting and the frequency.

• SSNR : Select Able or Disable for the video noise elimination function.

• SSNR level : Adjust the noise reduction level.

• Iris : Select it to set the camera lens to auto or manual.

- DC(Auto) : The iris is automatically adjusted to the amount of the surrounding light.

- Manual : Sets the iris F-No to manual.

• Iris F-No : Set up the F value of the iris.

The image exposure can be saturated depending on the Shutter setup range.

● SETUP SCREEN

English _91

Page 92

setup screen

To Setup Special

1. Select <Special>.

2. Select each item and set it properly.

• Sharpness mode : Adjust the overall sharpness of the image. If selecting <On>, you can adjust the sharpness of the image.

• Sharpness level : The higher the level is, the sharper and clearer the outline of the image becomes.

• Color level : Adjust the strength of video color.

• Gamma : Adjust the contrast of the image.

Mitigate the degree of image vibration when the camera vibrates due to the external factors

such as wind.

92_ setup screen

Page 93

To Set Day/Night (SNB-8000)

1. Select <Day/Night>.

2. Select each item and set it properly.

• Day/Night : Mode is used to adjust the color of Color or Black and White.

- Color : The video is always output in color.

- B/W : The video is always output in black and white.

- Auto : Normally, it is set to Color but to B&W under low luminance at night.

If AGC of the <Exposure> menu is set to <Off>, the day/night mode cannot be set to <Auto>.

- External : It controls the color of the video when the alarm input terminal is synchronized with an external device.

- Schedule : Set the time during which the camera is operated in the color mode.

• Dwell Time : It specifies the period for which the selected brightness condition must be maintained to switch the lighting mode from Day to Night or vice versa.

• Duration : It specifies the interval of lighting mode conversion.

• Alarm in : The video is set to Color or B/W as the alarm sensor is open or closed.

If the Day/Night mode is set to External Input, the alarm input function of the Event-Alarm Input

page is disabled.

• Simple focus after D/N: The video is automatically focused after the lighting mode changes from Day to Night or vice versa.

• Activation time : Configure a schedule of operation.

If it is set, the Color mode is maintained from 00 second of the starting time to 59 second of the

ending time.

When <Simple focus after D/N> is set, the focusing function may not work properly under a

certain condition. For more details, refer to “Focus setup”. (Page 96)

● SETUP SCREEN

The Day/Night mode may not operate properly if the lens installed in the camera and the lens set

in <Lens> of the <Exposure> menu don’t match.

If you switch the day/night mode, the MD/VA event cannot be detected.

English _93

Page 94

setup screen

To Set Day/Night (SNV-8080)