Samsung SND-6084R User Manual

Download

Page 1

NETWORK CAMERA

User Manual

SND-6084R/

SNO-6084R/SNV-6084R

Page 2

Network Camera

User Manual

Trademark

The name of thi s product is the reg istered tradema rk of Samsung Techwin C o., Ltd. Other trad emarks mention ed in this manual are th e registered trad emark of their resp ective company.

Restriction

Samsung Techwi n Co., Ltd shall reser ve the copyrigh t of this document. U nder no circumst ances, this docu ment shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.

Disclaimer

Samsung Techwi n makes the best to ver ify the integri ty and correct ness of the conten ts in this document , but no formal guar antee shall be provi ded. Use of this do cument and the subse quent results sha ll be entirely on the u ser’s own responsib ility. Samsung Techwi n reserves the ri ght to change the con tents of this docum ent without prio r notice.

Design and specifications are subject to change without prior notice.

The defau lt password c an be exposed to a h acking thread s o it is recommen ded to change th e password

after in stalling the pr oduct. Note that t he security a nd other relat ed issues caus ed by the unchan ged password s hall be respon sible for the use r.

is the regist ered logo of Samsun g Techwin Co., Ltd.

Page 3

overview

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings, Install in accordance with the manufacturer’s

instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized

plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/ accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by

the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lighting storms or when unused for

long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

● OVERVIEW

English _3

Page 4

overview

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT.

Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance with the installation instructions.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

4_ overview

Page 5

Class construction

An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection.

Battery

Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

Disconnection Device

Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location.

When used outside of the U.S., it may be used HAR code with fittings of an approved agency is employed.

CAUTION

Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

The CVBS out terminal of the product is provided for easier installation, and is not recommended for monitoring purposes.

Please use the input power with just one camera and other devices must not be connected.

The ITE is to be connected only to PoE networks without routing to the outside plant.

● OVERVIEW

English _5

Page 6

overview

Please read the following recommended safety precautions carefully.

yDo not place this apparatus on an uneven surface. yDo not install on a surface where it is exposed to direct sunlight, near

heating equipment or heavy cold area. yDo not place this apparatus near conductive material. yDo not attempt to service this apparatus yourself. yDo not place a glass of water on the product. yDo not install near any magnetic sources. yDo not block any ventilation openings. yDo not place heavy items on the product.

User’s Manual is a guidance book for how to use the products.

The meaning of the symbols are shown below.

yReference : In case of providing information for helping of product’s usages yNotice : If there’s any possibility to occur any damages for the goods and

human caused by not following the instruction

 Please read this manual for the safety before using of goods and keep it in

the safe place.

6_ overview

Page 7

CONTENTS

OVERVIEW

INSTALLATION &

CONNECTION

NETWORK CONNECTION

AND SETUP

3 Important Safety Instructions 9 Product Features 11 Recommended PC Specifications 12 Recommended Micro SD/

SDHC/SDXC Memory Card Specifications

12 What’s Included 15 At a Glance (SND-6084R) 19 At a Glance (SNO-6084R) 23 At a Glance (SNV-6084R)

26 Installation (SND-6084R) 28 Installation (SNO-6084R) 29 Installation (SNV-6084R) 38 Inserting/Removing a Micro SD

Memory Card (SND-6084R/SNV6084R)

40 Memory Card Information

(Not Included)

41 Connecting with other Device

50 Connecting the Camera Directly

to Local Area Networking

51 Connecting the Camera Directly

to a DHCP Based DSL/Cable Modem

52 Connecting the Camera Directly

to a PPPoE Modem

53 Connecting the Camera to a

Broadband Router with the PPPoE/Cable Modem

54 Buttons used in IP Installer 55 Static IP Setup 59 Dynamic IP Setup

Port Range Forward (Port Mapping)

Setup

62 Connecting to the Camera from a

Shared Local PC

62 Connecting to the Camera from a

Remote PC via the Internet

● OVERVIEW

English _7

Page 8

overview

WEB VIEWER

SETUP SCREEN

APPENDIX

130

63 Connecting to the Camera 65 Login 66 Installing Silverlight Runtime 70 Installing STW WebViewer Plugin 72 Using the Live Screen 75 Playing the recorded video

81 Setup 81 Video & Audio Setup 96 Network Setup 107 Event Setup 123 System Setup

130 Specification 135 Product Overview 138 Troubleshooting 140 Open Source Announcement

8_ overview

Page 9

PRODUCT FEATURES

• Dustproof/Waterproof (IP66) (SNO-6084R/SNV-6084R)

The dustproof and waterproof design makes you feel at ease when installing the product outdoors or exposing it to rain.

• SSNR3 (Samsung Super Noise Reduction)

The high-performance DSP chip effectively removes the GAIN noise of low light level and shows a clear and sharp image even in dark places.

• Day & Night (ICR)

It automatically detects the time change of the day to switch to a mode that is appropriate to the current scene. In a daylight scene, it switches to the color mode for maintaining the optimal color tones while it, at night, switches to B/W mode for identifying the low contrast scene.

• IR mode

If the IR indicator turns on, the product switches to the IR mode for preventing an object from being too bright, which helps you identify the object in near distance.

• Visibility: 15m (SND-6084R/SNV-6084R)

In B/W mode, the IR indicator turns on with the effective visibility of 15m at 0 Lux.

• Visibility: 30m (SNO-6084R)

In B/W mode, the IR indicator turns on with the effective visibility of 30m at 0 Lux.

• SSDR (Samsung Super Dynamic Range)

For a scene showing a great contrast difference such as backlight scene, the product maintains the bright areas while selectively making the dark areas brighter to balance the overall contrast.

• Others

Other features include: HLC (High Light Compensation), SENS-UP, V-REV, H-REV, D-ZOOM, SHARPNESS, Motion Detection, PRIVACY.

• Full HD Video Quality

• Multi-Streaming

This network camera can display videos in different resolutions and qualities simultaneously using different CODECs.

• Web Browser-based Monitoring

Using the Internet web browser to display the image in a local network environment.

● OVERVIEW

English _9

Page 10

overview

• Alarm

If an event occurs, the event-related video will be transferred to the FTP/email specified

by the user or saved to the Micro SD memory, or the event signal will be sent to the Alarm

Out port.

• Built-in SD Memory (SNO-6084R)

This product is equipped with an internal 4GB memory card (SDHC).

• Tampering Detection

Detects tempering attempts on video monitoring.

• Motion Detection

Detects motion from the camera’s video input.

• Intelligent Video Analysis

Analyzes video to detect logical events of specified conditions from the camera’s video

input.

• Face Detection

Detects faces from the camera’s video input.

• Audio Detection

Detects sound louder than a certain level specified by user.

• Auto Detection of Disconnected Network

Detects network disconnection before triggering an event.

• ONVIF Compliance

This product supports ONVIF Profile-S.

For more information, refer to www.onvif.org.

10_ overview

Page 11

RECOMMENDED PC SPECIFICATIONS

• CPU : Intel Core 2 Duo 2.4 GHz or higher (for using 1920x1080 30 fps) Intel Core i7 2.8 GHz or higher (for using 1920x1080 60 fps)

Web Plug-in is optimized to SSE 4.1 Instruction Set.

• Operating System : Windows XP, VISTA, 7, 8, Mac OS X

• Resolution : 1280X1024 pixels or higher (32 bit color)

• RAM : 2GB or higher

• Web Browser : Microsoft Internet Explorer (Ver. 10, 9, 8, 7), Mozilla Firefox (Ver. 19, 18,

17, 16, 15, 14, 13, 12, 11, 10, 9), Google Chrome (Ver. 25, 24, 23, 22, 21, 20, 19, 18, 17, 16, 15), Apple Safari (Ver. 6.0.2(Mac OS X 10.8, 10.7 Only), 5.1.7)

Windows 8 is supported only in the Desktop mode.

Neither a beta test version unlike the version released in the company website nor the developer version will

be supported.

For IPv6 connection, Window 7 or higher is recommended.

For Mac OS X, only the Safari browser is supported.

• Video Memory : 256MB or higher

If the driver of the video graphic adapter is not installed properly or is not the latest version, the

video may not be played properly.

For a multi-monitoring system involving at least 2 monitors, the playback performance can be

deteriorated depending on the system.

● OVERVIEW

English _11

Page 12

overview

Mircro SD

RECOMMENDED MICRO SD/SDHC/SDXC MEMORY CARD SPECIFICATIONS

• 4GB ~ 64GB

• For your camera, we recommend you use a memory card from the following manufacturers: Micro SD/SDHC/SDXC Memory Card : Sandisk, Transcend

• For the framerate below 30 fps, it is recommended to use the specification memory card of Class 6 or higher.

• For the framerate over 31 fps, it is recommended to use the specification memory card of Class 10 UHS or higher.

• It is recommended to set the storage frame rate to 30 fps or lower when you use the embedded SD memory card. For the storage frame of 31 fps or higher, it is recommended to contact the service center and replace the memory card with the one for Class 10 UHS or higher class memory card. (It is applicable only to the SNO-6084R model.)

WHAT’S INCLUDED

Please check if your camera and accessories are all included in the product package.

Appearance Item Name

Quantity

Description Model Name

+ -

AC 24V / DC 12V

RESET

VIDEO

12_ overview

Mircro SD

Camera

Instruction book, Installer S/W CD,

CMS S/W DVD

SND-6084R or

SNO-6084R or

SNV-6084R

SND-6084R/

SNO-6084R/

SNV-6084R

Page 13

Appearance Item Name

Quantity

Description Model Name

Quick Guide

(Optional)

Warranty card

(Optional)

Cable for the testing

monitor

Used to test the camera

connection to a portable display

device

Power Terminal Block 1 Plugged in the power plug

Template

Product installation guide

Used to control the direction of

L Wrench

the camera / Used to remove and

replace the dome cover

SND-6084R/ SNO-6084R/

SNV-6084R

SND-6084R/ SNO-6084R/

SNV-6084R

SND-6084R/ SNO-6084R/

SNV-6084R

SND-6084R/

SNV-6084R

SND-6084R/

SNV-6084R

SNO-6084R/

SNV-6084R

Alarm Cable 1 Useful for alarm connection SND-6084R

Screw 2

Tapping Screw 3

Useful for installation on the

ceiling, wall, etc.

Used for installation on the wall

or ceiling

SND-6084R

SNO-6084R

● OVERVIEW

English _13

Page 14

overview

Appearance Item Name

Sunshield 1

Sunshield Hold 1

CAUTION: Be ware of the Rated Voltage and Polarity

of the power connection.

Power Cable

Audio/alarm cable

Tapping Screw

Plastic Anchor

Machine Screws 3

Indoor Buried Housing

Quantity

Description Model Name

It protects the camera from the

direct sunlight.

It fixes the sunshield with the

Used to plug into the power port

Used to connect with the

audio and alarm port

Used for installation on the

wall or ceiling

For fixing a screw,

Inserted in a hole

(reinforced anchoring force)

Used for assembling the dome case when installing the product on the pipe, wall mount, etc. or

blocking a hole.

Options (not included)

Housing for installing indoor

buried type cameras

camera.

SNO-6084R

SNV-6084R

SND-6084R/

SNV-6084R

14_ overview

Page 15

AT A GLANCE (SND-6084R)

Appearance

Item Description

Dome cover

Case cover used to protect the lens and the main unit.

● OVERVIEW

Camera Case

Housing part that covers the camera body.

English _15

Page 16

overview

Components

b cd

e f

h i

16_ overview

klm nj

Page 17

Item Description

Internal Cover It is a cover to protect the main body.

Illumination Sensor Detects incoming light to control the IR LED.

Lens Lens for the camera.

IR LED These infrared LED’s are controlled by the illumination sensor.

T Zoom in (Tele)

Zoom/Focus Control

Button

Reset Button

Test Monitor Out

Alarm I/O Port

W Zoom out (Wide)

N Focusing on a near object (Near)

F Focusing on a far object (Far)

Focus Control Press this button for automatic focus control.

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.

If you reset the camera, the network settings will be adjusted so that

DHCP can be enabled. If there is no DHCP server in the network, you must run the IP Installer program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network.

Output port for test monitoring the video output. Use the test monitor cable to connect to a mobile display and check the test video.

ALARM IN

ALARM OUT Used to connect the alarm output signal.

GND Common port for alarm output signal.

Used to connect the alarm input sensor or external day/ night sensor.

● OVERVIEW

Power Port Port for power terminal block.

English _17

Page 18

overview

Item Description

Micro SD Memory

Card Compartment

Audio Out Jack Used to connect to speakers.

Audio In Jack Used to connect to a microphone.

Network Port Used to connect the PoE or Ethernet cable for network connection.

Microphone hole A microphone is embedded.

Compartment for the Micro SD memory card.

18_ overview

Page 19

AT A GLANCE (SNO-6084R)

Appearance

Item Description

Sunshield It protects the camera from the direct sunlight.

Sunshield Hold It fixes the sunshield with the camera.

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.

If you reset the camera, the network settings will be adjusted so that

Reset Button

● OVERVIEW

c d

English _19

Page 20

overview

Item Description

Zoom/Focus Control

Button

Test Monitor Out

Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you have applied

ethanol.

T Zoom in (Tele)

W Zoom out (Wide)

N Focusing on a near object (Near)

F Focusing on a far object (Far)

Focus Control Press this button for automatic focus control.

Output port for test monitoring the video output. Use the test monitor cable to connect to a mobile display and check the test video.

20_ overview

Page 21

Components

a b

CAUTION:Be ware of the

Rated Voltage and Polarity of the power connection.

ARM-IN

GND

ARM-OUT

c d

f g

Item Description

Power Port Used to plug the power cable.

ARM-IN

Alarm I/O Port

Network Port Used to connect the PoE or Ethernet cable for network connection.

GND Common port for alarm output signal.

ARM-OUT Used to connect the alarm output signal.

Used to connect the alarm input sensor or external day/ night sensor.

● OVERVIEW

English _21

Page 22

overview

Item Description

Audio Out Jack Used to connect to speakers.

Audio In Jack Used to connect to a microphone.

IR LED These infrared LED’s are controlled by the illumination sensor.

Illumination Sensor Detects incoming light to control the IR LED.

22_ overview

Page 23

AT A GLANCE (SNV-6084R)

Mircro SD

Appearance

+ -

AC 24V / DC 12V

Item Description

Dome cover

Case cover used to protect the lens and the main unit.

● OVERVIEW

Mircro SD

RESET

VIDEO

Camera Case

Housing part that covers the camera body.

English _23

Page 24

overview

Components

b dc

+ -

AC 24V / DC 12V

RESET

VIDEO

e fgh

i kj

24_ overview

Page 25

Item Description

Internal Cover It is a cover to protect the main body.

Illumination Sensor Detects incoming light to control the IR LED.

Lens Lens for the camera.

IR LED These infrared LED’s are controlled by the illumination sensor.

Power Port Port for power terminal block.

Test Monitor Out

Reset Button

Zoom/Focus Control

Button

Micro SD Memory

Card Compartment

Audio and alarm

cable port

Output port for test monitoring the video output. Use the test monitor cable to connect to a mobile display and check the test video.

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.

If you reset the camera, the network settings will be adjusted so that

T Zoom in (Tele)

W Zoom out (Wide)

N Focusing on a near object (Near)

F Focusing on a far object (Far)

Focus Control Press this button for automatic focus control.

Compartment for the Micro SD memory card.

Plug in the audio and alarm cable to this port to connect with external alarm device/microphone/speaker.

● OVERVIEW

Network Port Used to connect the PoE or Ethernet cable for network connection.

English _25

Page 26

installation & connection

Precautions before installation

Ensure you read out the following instructions before installing the camera:

• It must be installed on the area (ceiling or wall) that can withstand 5 times the weight of the camera including the installation bracket.

• Stuck-in or peeled-off cables can cause damage to the product or a fire.

• For safety purposes, keep anyone else away from the installation site. And put aside personal belongings from the site, just in case.

INSTALLATION (SND-6084R)

Disassembling

1. Use one hand to hold the camera’s bottom part

and turn the cover counterclockwise with another hand to separate it.

2. Lift up the inner cover to separate it.

26_ installation & connection

Page 27

Installation

1. Attach the installation template to the

selected area and punch 3 holes as shown in the figure.

● INSTALLATION & CONNECTION

2. Use the 2 supplied screws to fix the camera

to the 2 punched holes.

Set the <FRONT TOP> mark imprinted on the

camera to face the direction of camera monitoring.

3. Connect the camera internal terminal with the

corresponding cable.

Adjust the lens in a desired direction by referring to the “Adjusting the monitoring

direction for the camera” section. (page 37)

5. Fasten the dome case (dome cover +

camera case) to the main body as shown in the figure.

Pay attention to the direction for assembly.

3. GND

2. ALARM IN

1. ALARM OUT

VIDEO

1 2 3

DC 12V

RESET

TOP

FRONT

English _27

Page 28

installation & connection

INSTALLATION (SNO-6084R)

This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the

external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.

Installation

1. Fix the camera in 3 holes by tightening the

three tapping screws supplied with the product.

2. Connect the cables with the camera port.

3. Adjust the direction of the camera with the

L-wrench supplied with the product.

Outdoor installation

When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside.

1. Connect the power, I/O, BNC, and LAN

cables.

2. Wrap the black cable jacket (Area A) and the

cable connection area with waterproof (butyl rubber) tape so that more than half of the butyl rubber tape is overlapped.

If the cable jacket is not waterproofed properly,

then it can directly cause leakage. Make sure to protect the cable with a dense layer of taping.

Waterproof butyl tape is made of butyl rubber that can be stretched to twice its normal length.

Camera

System

28_ installation & connection

Page 29

INSTALLATION (SNV-6084R)

This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the

external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.

Disassembling

1. With the provided L-wrench, loosen

3 bolts on the dome cover counter clockwise to remove the cover.

● INSTALLATION & CONNECTION

Dome cover

2. Lift up the inner cover to separate it.

Bolts

Camera Body

AC 24V / DC 12V

+ -

VIDEO

Camera Case

RESET

VIDEO

RESET

English _29

Page 30

installation & connection

AC 24V / DC 12V

RESET

VIDEO

+ -

Installation

1. Drill a hole (diameter : 6mm, depth : min

55mm) of the case bottom and insert the provided plastic anchor to the end.

2. Fit the bottom hole to the anchor hole and

insert and fix the taping screw (M4.5xL50).

3. Connect and arrange the necessary cables

lest that they should be damaged or twisted while installing the camera.

4. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for the camera" section. (page

37)

5. Close the dome cover.

`To ensure waterproofing, tight up the fixing bolts using the L-wrench.

VIDEO

RESET

AC 24V / DC 12V

+ -

30_ installation & connection

Page 31

Connecting waterproof power cable and LAN cable

If the LAN cable is not connected indoors

1. Remove the dome cover and the case.

2. Pull out the long projected part of the rubber plug on

the bottom and remove it as shown in the figure.

3. Insert the power cable into the small hole made by

removing the projected part of the rubber plug in step 2 above, and lay the cable along the long groove.

4. Connect the power cable with the power terminal

block.

● INSTALLATION & CONNECTION

CAUTION: Be ware o f the

Rated Voltage and P olari ty

of the power conne ction .

English _31

Page 32

installation & connection

5. Insert the LAN cable into the large hole made by removing the projected part of the rubber plug in step 2 above.

6. Remove the sheath with a cable cutter, and align the cables.

7. Connect the LAN cable with a LAN connector, and insert it into the LAN tool.

8. Connect the finished cable to the Ethernet port.

If the LAN cable is connected indoors

1. Remove the dome cover and the case.

2. Pull out the rubber plug on the bottom as shown in

the figure.

3. Insert the power cable into the hole, and lay the cable along the long groove.

4. Connect the power cable with the power terminal block.

5. Insert the LAN cable into the hole, and connect the cable with the Ethernet port.

CAUTION: Be ware o f the Rated Voltage and P olari ty

of the power conne ction .

32_ installation & connection

Page 33

Connecting alarm cable

1. Remove the dome cover and the case.

2. Pull out the rubber plug on the bottom as shown in

the figure.

3. Insert the alarm cable into the hole made by

removing the rubber plug in step 2, and connect the cable with the PCB alarm terminal.

4. Align the cable so that it should not be damaged or

jammed when installing the camera.

5. Put the rubber plug of the alarm cable into the hole.

6. Adjust the lens in a desired direction by referring to

the “Adjusting the monitoring direction for the camera” section.

7. Attach the dome cover.

(page 37)

● INSTALLATION & CONNECTION

English _33

Page 34

installation & connection

Attaching to the unbundled adapter

Choose and purchase a necessary one of the following options (unbundled) that is suitable to the installation site or for your convenience.

1. Remove the dome cover from the case by referring to the “Disassembling” section. (page 29)

2. Use the provided machine screw to fix the camera case to the unbundled adapter.

3. Connect and arrange the necessary cables lest that they should be damaged or twisted while installing the camera.

4. Install the camera body in the reverse order of “Disassembling”.

5. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for the camera” section. (page 37)

6. Close the dome cover.

`To ensure waterproofing, tight up the fixing bolts using the L-wrench.

Outdoor installation

1. Connect the power, I/O, BNC, and LAN cables.

2. Wrap the black cable jacket (Area A) and the cable connection area with waterproof (butyl rubber) tape so that more than half of the butyl rubber tape is overlapped.

If the cable jacket is not waterproofed properly,

then it can directly cause leakage. Make sure to protect the cable with a dense layer of taping.

Waterproof butyl tape is made of butyl rubber that can be stretched to twice its normal length.

Camera

System

34_ installation & connection

Page 35

Optional Accessories for Installation

For your easier installation, you can purchase appropriate optional accessories available.

1. WALL MOUNT ADAPTOR(SBP-300WM or

SBP-300WM1)/HANGING MOUNT (SBP-301HM2 : SND-6084R, SBP-301HM3 : SNV-6084R) This adaptor is used when installing the dome camera onto a wall.

2. CEILING MOUNT ADAPTOR(SBP-300CM)/

HANGING MOUNT(SBP-301HM2 : SND-6084R, SBP-301HM3 : SNV-6084R) This adaptor is used when installing the dome camera on a concrete ceiling.

● INSTALLATION & CONNECTION

English _35

Page 36

installation & connection

3. POLE MOUNT ADAPTOR(SBP-300PM) This is an adaptor for WALL MOUNT ADAPTOR (SBP-300WM or SBP-300WM1) installation on a pole whose diameter is bigger than 80mm.

4. CORNER MOUNT ADAPTOR (SBP-300KM) This is an adaptor for WALL MOUNT ADAPTOR (SBP-300WM or SBP-300WM1) installation on the corner of wall joint.

36_ installation & connection

Page 37

Adjusting the monitoring direction for the camera (SND-6084R/ SNV-6084R)

Pan

3. GND

2. ALARM IN

1. ALARM OUT

VIDEO

1 2 3

RESET

Tilt

`Adjusting the monitoring direction

You can adjust the camera direction only when the camera is fixed on the ceiling. Where, rotating the camera unit to the left or right is called Pan, adjusting the tilt is called Tilt, and turning the lens on its axis is called Rotation.

- The effective range of pan is a total of 354 degrees.

- The effective range of rotation is a total of 355 degrees.

- The effective range of tilt is a total of 67 degrees.

The image can be covered up by the camera case depending on the angle.

Do not forcefully turn the focus/zoom lens after the dome case is disassembled.

Otherwise, it may cause an incorrect focus due to a motor failure.

`Methods of adjustment

1. After installing the camera, adjust the panning angle in consideration of the

monitoring direction.

2. Set the horizontal angle so that the image is not reversed.

`In case of the SND-6084R model, rotate the lens with the cover on the rear of the lens unit.

3. Adjust the tilt angle so that the camera faces toward the monitoring object.

DC 12V

TOP

FRONT

Lens rotation

● INSTALLATION & CONNECTION

English _37

Page 38

installation & connection

INSERTING/REMOVING A MICRO SD MEMORY CARD (SND-6084R/SNV-6084R)

Disconnect the power cable from the camera before inserting the Micro SD memory card.

Do not insert the Micro SD memory card while it’s upside down by force.

Otherwise, it may damage the Micro SD memory card.

Inserting a Micro SD Memory Card

Push the Micro SD memory card in the direction of the arrow shown in the diagram.

<SND-6084R>

38_ installation & connection

<SNV-6084R>

Page 39

Removing a Micro SD Memory Card

Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot.

<SND-6084R>

● INSTALLATION & CONNECTION

<SNV-6084R>

Pressing too hard on the Micro SD memory card can cause the card to shoot out uncontrollably

from the slot when released.

To pull out the micro SD memory card, turn off the camera power or set the device to <Off> of

<Storage> and press the [Apply (

If you turn off the camera or remove the Micro SD memory card that contains data from the

product, the data may be lost or damaged.

)] button. (Page 108)

English _39

Page 40

installation & connection

MEMORY CARD INFORMATION (NOT INCLUDED)

What is a memory card?

The memory card is an external data storage device that has been developed to offer an entirely new way to record and share video, audio, and text data using digital devices.

Selecting a memory card that’s suitable for you

Your camera supports Micro SD/SDHC/SDXC memory cards. You may, however, experience compatibility issues depending on the model and make of the memory card.

For your camera, we recommend you use a memory card from the following manufacturers: Micro SD/SDHC/SDXC Memory Card : Sandisk, Transcend

Memory cards of 4GB ~ 64GB is recommended for using with this camera.

Playback performance can be affected depending on the speed of memory card, so use the high-speed memory card.

For the framerate below 30 fps, it is recommended to use the specification memory card of Class 6 or higher.

For the framerate over 31 fps, it is recommended to use the specification memory card of Class 10 UHS or higher.

Memory Card Instructions (SNO-6084R)

This product is equipped with an internal 4GB memory card (SDHC).

It is recommended to set the storage frame rate to 30 fps or lower when you use the embedded SD memory card.

For the storage frame of 31 fps or higher, it is recommended to contact the service center and replace the memory card with the one for Class 10 UHS or higher class memory card.

Do not dismantle this product by yourself for a reason such as waterproofing.

Memory Card Components

Contacts

Micro SD/SDHC/SDXC

40_ installation & connection

Page 41

CONNECTING WITH OTHER DEVICE

Ethernet

Power

ARM-IN

GND

ARM-OUT

<SND-6084R>

CAUTION:Be ware of the

Rated Voltage and Polarity of the power connection.

Monitor to install

● INSTALLATION & CONNECTION

Power

<SNO-6084R>

Monitor to install

English _41

Page 42

installation & connection

+ -

AC 24V / DC 12V

RESET

VIDEO

Monitor to install

Ethernet

Power

The CVBS out terminal of the product is provided for easier installation, and is not recommended

for monitoring purposes.

42_ installation & connection

CAUTION: Be ware o f the

Rated Voltage and Polari ty

of the power conn ection .

<SNV-6084R>

Page 43

Ethernet Connection

Connect the Ethernet cable to the local network or to the Internet.

Power Supply (SND-6084R)

Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the camera.

If both PoE and DC 12V are applied simultaneously, the product will be supplied with power from

PoE.

- You can also use a router featuring PoE to supply power to the camera.

- Use PoE that is compliant with the IEEE 802.3af protocols.

- It is advisable to use only one power source from PoE and DC 12V.

Be careful not to reverse the polarity when you connect the power cable.

If you want to connect an external device, you must turn off the external device before proceeding.

Power Supply (SNO-6084R/SNV-6084R)

Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the camera.

When connecting PoE and DC 12V, or PoE and AC 24V at the same time, the unit starts operation

with the first connected power.

- You can also use a router featuring PoE to supply power to the camera.

- Use PoE that is compliant with the IEEE 802.3af protocols.

The heater will operate properly only by the power source of AC 24V.

- The heater does not work with DC 12V, PoE.

- Use AC 24V in a low-temperature place of less than -10°C.

Be careful not to reverse the polarity when you connect the power cable.

AC 24V can be connected in non-polar union.

If you want to connect an external device, you must turn off the external device before proceeding.

● INSTALLATION & CONNECTION

English _43

Page 44

installation & connection

Power Cable Specification for Each Model

In case of DC 12V Input:

Wire Type (AWG) #22 #20 #18

SND-6084R

Cable Length (Max.)

SNV-6084R

In case of AC 24V Input:

Wire Type (AWG) #22 #20 #18

Cable Length (Max.)

SNO-6084R

SNV-6084R

Network Cable Specification

Item Contents Remark

Connector RJ45

Ethernet 10/100Base-T 10/100 Mbps

Cable UTP Category 5e

Max Distance 100M

PoE Support IEEE 802.3af

24m 38m 60mSNO-6084R

34m 55m 88m

44_ installation & connection

Page 45

Connecting to Audio Input/Output

Speaker

Amp Amp Microphone

Speaker

Microphone

Network

● INSTALLATION & CONNECTION

Speaker

Microphone

Speaker

Microphone

Amp

Speaker

CAUTION:Be ware of the

Rated Voltage and Polarity of the power connection.

ARM-IN

GND

ARM-OUT

English _45

Page 46

installation & connection

Speaker

Microphone

Network

Speaker

Speaker Amp Amp

1. Connect the AUDIO IN port of the camera with the microphone or LINE OUT port of

the amplifier that the microphone is connected to.

As a microphone is built in, you can use the built-in microphone instead of an external one.

(It is applicable only to the SND-6084R model.)

2. Connect the AUDIO OUT port of the camera with the speaker or LINE IN port of the

amplifier that the speaker is connected to.

3. Check the specifications for audio input.

• Audio Codec

- Audio In : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz), G.726 ADPCM (Bit Rate: 16Kbps, 24Kbps, 32Kbps, 40Kbps / Sampling Frequency: 8kHz)

- Audio Out : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz)

• Full duplex Audio

• Audio in : Mono signal line input (Max.2.4 Vpp)

• Audio out : Mono signal line output (Max.2.4 Vpp)

• Line out impedance : 600Ω

Microphone

46_ installation & connection

Page 47

Connecting to the I/O port box

Connect the Alarm I/O cable to the corresponding port of the port box.

Sensor Alarm

(Warning lamp)

<SND-6084R>

CAUTION:Be ware of the

Rated Voltage and Polarity of the power connection.

ARM-IN

GND

ARM-IN

ARM-OUT

● INSTALLATION & CONNECTION

Sensor

Alarm

(Warning lamp)

<SNO-6084R>

English _47

Page 48

installation & connection

Sensor

• ALARM-IN : Used to connect the alarm input sensor or external day/night sensor.

• ALARM-OUT : Used to connect the alarm output signal.

• GND : Common port for alarm output signal

If devices (e.g., flashing light and siren) that exceed the voltage and current specifications are

connected by using the open collector method, it may cause malfunction. Refer to the “Alarm Out Wiring Diagram” when connecting devices that exceed the voltage and current specifications. (page 49)

Alarm

(Warning lamp)

<SNV-6084R>

48_ installation & connection

Page 49

To connect the external sensor

Connect one strand of each signal line (2-strand) of the sensors to the [ALARM IN] port, and connect the other strand to the [GND] port.

Alarm In Wiring Diagram

External

connection

Sensor

Inside of the camera

GND

VCC_3.3V

RESISTOR RESISTOR

RESISTORALARM IN (5mA SINK)

TRANSISTOR

MLCC

GND

DIODE

To connect the alarm out

If devices (e.g., flashing light and siren) that exceed the voltage and current specifications are connected by using the open collector method, it may cause malfunction.

Refer to the alarm out connection diagram below when connecting devices that exceed the voltage and current specifications.

Alarm Out Wiring Diagram

● INSTALLATION & CONNECTION

Warning lamp /

Siren power

(-) (+)

Warning lamp /

Siren

External connection Inside of the camera

DC 5V or 3.3V

DIODE

RELAY

RESISTOR 10K ohm

TRANSISTOR

GND

ALARM OUT (12VDC 20mA MAX)

RESISTOR

TRANSISTOR

GND

English _49

Page 50

network connection and setup

You can set up the network settings according to your network configurations.

CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING

Connecting to the camera from a local PC in the LAN

1. Launch an Internet browser on the local PC.

2. Enter the IP address of the camera in the address bar of the browser.

Camera

INTERNET

Camera

Local PC

A remote PC in an external Internet out of the LAN network may not be able to connect to the

camera installed in the intranet if the port-forwarding is not properly set or a firewall is set. In this case, to resolve the problem, contact your network administrator.

By factory default, the IP address will be assigned from the DHCP server automatically.

If there is no DHCP server available, the IP address will be set to 192.168.1.100. To change the IP address, use the IP Installer. For further details on IP Installer use, refer to “Static IP Setup”. (Page 55)

50_ network connection and setup

Firewall

External Remote PC

DDNS Server (Data Center, KOREA)

Page 51

CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE MODEM

Camera

1. Connect the user PC directly with the network camera.

2. Run the IP Installer and change the IP address of the camera so that you can use

the web browser on your desktop to connect to the Internet.

3. Use the Internet browser to connect to the web viewer.

4. Move to [Setup] page.

5. Move to [Network] – [DDNS] and configure the DDNS settings.

6. Move to [Network] – [Interface], and set the network type to [DHCP].

7. Connect the camera, which was removed from your PC, directly to the modem.

8. Restart the camera.

For registering the DDNS settings, refer to “Registering with DDNS”. (page 99)

For configuring the DDNS settings, refer to “DDNS”. (page 98)

For setting the network type, refer to “Interface”. (page 96)

DSL/Cable Modem

INTERNET

DDNS Server

(Data Center, KOREA)

External Remote PC

●

NETWORK CONNECTION AND SETUP

English _51

Page 52

network connection and setup

CONNECTING THE CAMERA DIRECTLY TO A PPPoE MODEM

Camera

1. Connect the user PC directly with the network camera.

2. Run the IP Installer and change the IP address of the camera so that you can use

the web browser on your desktop to connect to the Internet.

3. Use the Internet browser to connect to the web viewer.

4. Move to [Setup] page.

5. Move to [Network] – [DDNS] and configure the DDNS settings.

6. Move to [Network] - [Interface] Setup Page, set the network type to [PPPoE], and

enter the ID and password.

7. Connect the camera, which was removed from your PC, directly to the modem.

8. Restart the camera.

For registering the DDNS settings, refer to “Registering with DDNS”. (page 99)

For configuring the DDNS settings, refer to “DDNS”. (page 98)

For setting the network type, refer to “Interface”. (page 96)

PPPoE Modem

INTERNET

DDNS Server

(Data Center, KOREA)

External Remote PC

52_ network connection and setup

Page 53

CONNECTING THE CAMERA TO A BROADBAND ROUTER WITH THE PPPoE/CABLE MODEM

This is for a small network environment such as homes, SOHO and ordinary shops.

Camera

PPPoE or

Broadband

Camera

Local PC

Router

Cable Modem

Configuring the network settings of the local PC connected to a Broadband Router

Configuring the network settings of the local PC connected to a Broadband Router, follow the instructions below.

• Select : <Network Neighborhood>  <Properties>  <Local Area Connection> <Properties>  <General>  <Internet Protocol (TCP/IP)>  <Properties> 



<Obtain an IP address automatically> or <Use the following IP address>.

• Follow the instructions below if you select <Use the following IP address>:

ex1) If the address (LAN IP) of the Broadband Router is 192.168.1.1

IP address : 192.168.1.100 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.1.1

ex2) If the address (LAN IP) of the Broadband Router is 192.168.0.1

IP address : 192.168.0.100 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.0.1

ex3) If the address (LAN IP) of the Broadband Router is 192.168.xxx.1

IP address : 192.168.xxx.100 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.xxx.1

For the address of the Broadband Router, refer to the product’s documentation.

For more information about port forwarding of the broadband router, refer to "Port Range

Forward (Port Mapping) Setup”. (Page 60)

INTERNET

PPPoE or

Cable Modem

DDNS Server (Data Center, KOREA)

External Remote PC

English _53

●

NETWORK CONNECTION AND SETUP

Page 54

network connection and setup

BUTTONS USED IN IP INSTALLER

a b c d e f g

h i j k l m

Item Description

Device Name

Alias This function is not currently implemented.

Mode

MAC(Ethernet)

Address

IP Address

Protocol

Model name of the connected camera. Click the column to sort the list by model name. However, search will be stopped if clicked during the search.

Displays either <Static>, <Dynamic> or <PPPoE> for the current network connection status.

Ethernet address for the connected camera. Click the column to sort the list by Ethernet address. However, search will be stopped if clicked during the search.

IP address. Click the column to sort the list by IP address. However, search will be stopped if clicked during the search.

Network setting for the camera. The factory default is “IPv4”. Cameras with the IPv6 setting will be displayed “IPv6”.

54_ network connection and setup

Page 55

Item Description

URL

IPv4 Scans for cameras with the IPv4 setting.

IPv6

Auto Set The IP Installer automatically configures the network settings.

Manual Set You should configure the network settings manually.

Exit Exits the IP Installer program.

For the IP installer, use only the installer version provided in the installation CD or use the latest one if

available. You can download the latest version from the Samsung web site (www.samsungcctv.com).

DDNS URL address enabling access from the external Internet. However, this will be replaced with the <IP Address> of the camera if DDNS registration has failed.

Scans for cameras with the IPv6 setting. Activated in an IPv6 compliant environment only.

Scans for cameras that are currently connected to the network. However, this button will be grayed out if neither IPv4 nor IPv6 is checked.

STATIC IP SETUP

Manual Network Setup

Run <IP Installer_v2.XX.exe> to display the camera search list. At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.

For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not

support this function.

1. Select a camera in the search list.

Check the MAC address of the camera on the camera’s label. Both the [Auto Set] and [Manual Set] buttons will be activated.

2. Click [Manual Set].

The Manual Setting dialog appears. <IP Address>, <Subnet Mask>, <Gateway>, <HTTP Port>, and <VNP Port> of the camera are displayed in the preset values.

●

NETWORK CONNECTION AND SETUP

English _55

Page 56

network connection and setup

3. In the <Address> pane, provide the

necessary information.

• MAC (Ethernet) Address : The MAC

address imprinted on the camera label is automatically displayed and requires no user setting.

IP related parameters can be set only

when DHCP is not checked.

If not using a Broadband Router

For setting <IP Address>, <Subnet Mask>, and <Gateway>, contact your network administrator.

4. In the <Port> pane, provide necessary

information.

• HTTP Port : Used to access the

camera using the Internet browser, defaulted to 80.

• VNP Port : Used to control the video

signal transfer, defaulted to 4520.

5. Enter the password. Enter the password of “admin” account, which was used to access the camera. The default password is “4321”.

The default password can be exposed to a hacking thread so it is recommended to change the

password after installing the product. Note that the security and other related issues caused by the unchanged password shall be responsible for the user.

If you want to change the password, refer to “Administrator password change” of the user

setup. (page 125)

6. Click [OK]. Manual network setup will be completed.

56_ network connection and setup

Page 57

If using a Broadband Router

• IP Address : Enter an address falling in the IP range provided by the Broadband Router. ex) 192.168.1.2~254,

192.168.0.2~254,

192.168.XXX.2~254

• Subnet Mask : The <Subnet Mask> of the Broadband Router will be the <Subnet Mask> of the camera.

• Gateway : The <Local IP Address> of the Broadband Router will be the <Gateway> of the camera.

The settings may differ depending on the connected Broadband Router model.

For more information, refer to the user manual of the applicable router.

For more information about port forwarding of the broadband router, refer to “Port Range

Forward (Port Mapping) Setup”. (Page 60)

If the Broadband Router has more than one camera connected

Configure the IP related settings and the Port related settings distinctly with each other.

ex)

Category Camera #1 Camera #2

●

NETWORK CONNECTION AND SETUP

IP related settings

Port related settings

If the <HTTP Port> is set other than 80, you must provide the <Port> number in the address bar

of the Internet browser before you can access the camera. ex) http://IP address : HTTP Port

IP Address Subnet Mask Gateway

HTTP Port VNP Port

http://192.168.1.100:8080

192.168.1.100

255.255.255.0

192.168.1.1

8080 4520

192.168.1.101

255.255.255.0

192.168.1.1

8081 4521

English _57

Page 58

network connection and setup

Auto Network Setup

Run <IP Installer_v2.XX.exe> to display the camera search list. At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.

For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not

support this function.

1. Select a camera in the search list.

Check the MAC address of the camera on the camera’s label. Both the [Auto Set] and [Manual Set] buttons will be activated.

2. Click [Auto Set].

The Auto Setting dialog appears. The <IP Address>, <Subnet Mask>, and <Gateway> will be set automatically.

3. Enter the password. Enter the password of “admin” account, which was used to access the camera. The default password is “4321”.

The default password can be exposed to

a hacking thread so it is recommended to change the password after installing the product. Note that the security and other related issues caused by the unchanged password shall be responsible for the user.

If you want to change the password, refer to “Administrator password change” of the user

setup. (page 125)

4. Click [OK]. Auto network setup will be completed.

58_ network connection and setup

Page 59

DYNAMIC IP SETUP

Dynamic IP Environment Setup

• Example of the Dynamic IP environment

- If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server

- If connecting the camera directly to modem using the DHCP protocols

- If IPs are assigned by the internal DHCP server via the LAN

Checking the Dynamic IP

1. Run the IP Installer on the user’s local

computer. Cameras allocated with <Dynamic IP> address are shown in the list.

2. Select a camera from the search result.

3. Click the [Manual Set] button and

check the camera’s <Dynamic IP> address. If you uncheck <DHCP>, you can change IP to <Static>.

●

NETWORK CONNECTION AND SETUP

English _59

Page 60

network connection and setup

PORT RANGE FORWARD (PORT MAPPING) SETUP

If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the Broadband Router so that a remote PC can access the camera in it.

Manual Port Range Forwarding

1. From the Setup menu of the Broadband Router, select <Applications & Gaming> - <Port Range Forward>.

For setting the port range forward for a third-party Broadband Router, refer to the user guide of that Broadband Router.

2. Select <TCP> and <UDP Port> for each connected camera to the Broadband Router. Each port number for the Broadband Router should match that specified in <Setup> - <Network> - <Port> from the camera’s web viewer menu.

3. When done, click [Save Settings]. Your settings will be saved.

Above sample instructions are based on the CISCO’s Broadband Router.

The settings may differ depending on the connected Broadband Router model.

For more information, refer to the user manual of the applicable router.

60_ network connection and setup

Page 61

Setting up Port Range Forward for several network cameras

When several network cameras are connected to one Broadband Router device, you should forward the TCP 943 port of the router to the TCP 943 port of a connected camera.

If you don't set properly the TCP 943 port of the router, you cannot get any video stream from the

web page of the camera.

• TCP 943 port is a port for the Silverlight policy server of a camera.

• You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page.

• You cannot change the Silverlight policy server port of a camera.

• You can change the ports of the camera except the policy server port through its configuration web pages.

When Camera1 and Camera2 are connected to a router :

●

NETWORK CONNECTION AND SETUP

User

Start End Protocol IP Address

943 943 TCP 192.168.1.100 3000 3000 TCP/UDP 192.168.1.100 3001 3001 TCP/UDP 192.168.1.101 4520 4520 TCP/UDP 192.168.1.100 4521 4521 TCP/UDP 192.168.1.101 8080 8080 TCP/UDP 192.168.1.100 8081 8081 TCP/UDP 192.168.1.101



Broadband Router

Port forwarding can be done without additional router setup if the router supports the UPnP (Universal Plug and Play) function. After connecting the network camera, set <Quick connect> of <Samsung DDNS> to <On> in the “Setup  Network  DDNS” menu.

Internet



Camera1 (192.168.1.100)



Policy server port 943

Camera2 (192.168.1.101)



Policy server port 943

HTTP port 8080

Device port 4520

RTSP port 3000

HTTP port 8081

Device port 4521

RTSP port 3001

English _61

Page 62

network connection and setup

CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC

1. Run the IP Installer.

It will scan for connected cameras and display them as a list.

2. Double-click a camera to access.

The Internet browser starts and connects to the camera.

Access to the camera can also be gained by typing the camera's IP address in the address bar of

the Internet browser.

CONNECTING TO THE CAMERA FROM A REMOTE PC VIA THE INTERNET

Since using the IP Installer on a remote computer that is not in the Broadband Router’s network cluster is not allowed, users can access cameras within a Broadband Router’s network by using the camera’s DDNS URL.

1. Before you can access a camera in the Broadband Router network, you should have

set the port range forward for the Broadband Router.

2. From the remote PC, launch the Internet browser and type the DDNS URL address

of the camera, or the IP address of the Broadband Router in the address bar. ex) http://www.samsungipolis.com/[Product ID]

For registering the DDNS settings, refer to “Registering with DDNS”. (page 99)

62_ network connection and setup

Page 63

web viewer

CONNECTING TO THE CAMERA

Normally, you would

1. Launch the Internet browser.

2. Type the IP address of the camera in

the address bar. ex) • IP address (IPv4) : 192.168.1.100

http://192.168.1.100



- the Login dialog should appear.

IP address (IPv6) : 2001:230:abcd:

•

ffff:0000:0000:ffff:1111

http://[2001:230:abcd:ffff:0000



:0000:ffff:1111] - the Login dialog should appear.

If the HTTP port is other than 80

1. Launch the Internet browser.

2. Type the IP address and HTTP port number of the camera in the address bar.

ex) IP address : 192.168.1.100:HTTP Port number(8080)

http://192.168.1.100:8080 - the Login dialog should appear.



Using URL

1. Launch the Internet browser.

2. Type the DDNS URL of the camera in the address bar.

ex) URL address : http://www.samsungipolis.com/[Product ID]

- the Login dialog should appear.

Network connection is disabled in the LAN only environment.

● WEB VIEWER

English _63

Page 64

web viewer

Connecting via UPnP

1. Run the client or operating system in support of the UPnP protocol.

2. Click the camera name for search.

In the Windows operating system, click the camera name searched from the network menu.

- The login window is displayed.

Connecting via Bonjour

1. Run the client or operating system in support of the Bonjour protocol.

2. Click the camera name for search.

In the Mac operating system, click the camera name searched from the Bonjour tab of Safari.

- The login window is displayed.

To check the DDNS address

If the camera is connected directly to the DHCP cable modem, DSL modem, or PPPoE modem, the IP address of your network will be changed each time you try to connect to the ISP (Internet Service Provider) server. If this is the case, you will not be informed of the IP address changed by DDNS.

Once you register a dynamic IP-based device with the DDNS server, you can easily check the changed IP when you try to access the device. To register your device to the <DDNS> server, visit www.samsungipolis.com and register your device first, and then set the Web Viewer’s <Network> - <DDNS> to <Samsung DDNS>, as well as providing <Product ID> that had been used for DDNS registration.

64_ web viewer

Page 65

Whenever you access the camera, the login window appears. Enter the User ID and password to access the camera.

1. Enter “admin” in the <User name>

input box. The administrator ID, “admin”, is fixed and can not be changed.

2. Enter “4321” in the <Password> input

box. If the password is changed, enter the changed password instead.

3. Click [OK].

If you have logged in successfully, you will the Live Viewer screen.

The default user ID is “admin”, and the

default password is “4321”.

For security purposes, ensure that you change the password in <System> - <User>.

The default password can be exposed to a hacking thread so it is recommended to change the

password after installing the product. Note that the security and other related issues caused by the unchanged password shall be responsible for the user.

If you check the “Remember my password” option when your input is done, in future you will be

logged in automatically without being prompted to enter the login information.

You will experience the best video quality if the screen size is 100%. Reducing the ratio may cut

the image on the borders.

● WEB VIEWER

English _65

Page 66

web viewer

INSTALLING SILVERLIGHT RUNTIME

If your PC has not installed Silverlight Runtime or has just installed an old runtime version, you will be redirected to the Silverlight Runtime installation page automatically when accessing the web viewer.

To install on Windows OS

1. Click <Click Here>.

2. When the file download dialog pops up, click <Run>.

3. When the download is completed, click <Run>.

4. The Silverlight Runtime installation page

will be displayed. <Install now> to proceed with the installation.

66_ web viewer

Page 67

5. When done, click <Close>.

To install on MAC OS

1. Run the file trailing with “.dmg”.

2. Run the install package file automatically created, ending

with “.pkg”.

3. Click <Continue>.

● WEB VIEWER

English _67

Page 68

web viewer

4. Select your language on the language selection screen, and click <Continue>.

5. Click <Agree>.

6. Click <Install>.

68_ web viewer

Page 69

7. Enter the password of the account

currently logged in, and click <Install

Software> and continue.

8. Once completed, click <Close>.

● WEB VIEWER

English _69

Page 70

web viewer

INSTALLING STW WebViewer PLUGIN

If connecting to a camera for the first time, you will see the installation message. Then, install the required WebViewer Plugin to access the camera and control the video from it in real time.

1. When the monitoring page is accessed for the very first time, the installation page is displayed. Click [Click Here] to begin installation.

If the plug-in installation file download status is suspended at 99% in the Internet Explorer

browser, retry it after selecting “Release SmartScreen filter” in “Tool  SmartScreen filter”.

2. Click [Run] in the message window.

3. Click [Yes] when the notice window

saying that all browser windows will be closed.

4. When the old version of the Web Viewer Plug-in is installed, a notice window saying the old version will be deleted is displayed. Click [Yes] when the notice window is displayed.

Steps 4 and 5 will be skipped if no Web Viewer Plug-in is installed.

70_ web viewer

Page 71

5. Click [OK].

The old version of Web Viewer Plug-in is deleted.

6. Click [Install] to begin installation of the

Web Viewer Plug-in.

7. Click [Finish].

STW Web Viewer Plug-in installation is completed.

● WEB VIEWER

English _71

Page 72

web viewer

USING THE LIVE SCREEN

a b d

e f g h i j

Item Description

Monitoring Move to the monitoring screen.

Playback Switch to the monitoring screen that plays recording data in the Micro SD memory.

Setup Move to the Setup screen.

Viewer Screen

Profile type

Screen

Optimization

Fix the resolution

Displays the Live video on the screen.

You can select a profile type in <Video profile> under the <Video & Audio> setup menu.

The video size of the camera will switch to as big as the Web browser.

Regardless of the resolution setup configured in the camera, it sets the resolution to 640x480. Press it again to switch back to the default resolution.

You can use the mouse wheel to activate the digital zooming in Viewer screen.

When the Web Viewer is connected, the profile information currently using is displayed.

72_ web viewer

Page 73

Item Description

Full Screen Switch the current video to the maximum size of the monitor.

Capture Saves the snapshot as an image file in the .bmp or .jpg format.

Audio/Microphone

Control

Alarm output Activate the Alarm Out port.

Hide the context

Enable Audio and Microphone are control the Audio volume.

Only the Audio volume can be controlled.

The left-corner context menu will disappear but only the menu icon.

To capture the snapshot

1. Click [Capture ( )] on the scene to

capture. The Capture dialog should appear.

2. Confirm the save path and click [Save]

button. The screenshot will be saved in the specified path.

If you encounter an interrupted video

when capturing the image with IE8 on a Windows 7-based PC, deselect “Turn On Protected Mode” from “Tools – Internet Options – Security”.

If the screen is not captured by IE browser in Windows 7 or 8, run the IE Browser with the Admin

privilege.

● WEB VIEWER

English _73

Page 74

web viewer

To fit the full screen

1. Click the [Full Screen (

2. This will fit the Viewer to the full screen.

3. To exit the full screen mode, press [Esc] on the keyboard.

For the Internet Explorer and Google Chrome browser, you can switch to the full screen.

To Use Audio

1. Click [Audio ( )] icon to activate audio communication.

2. Use [

] bar to control the volume.

If there is no sound from pulling in and out the audio jack while it is in operation, click the

[Audio (

To Use Microphone

Click [Mic ( )] icon to activate the microphone.

)] button.

)] icon to enable it again.

74_ web viewer

Page 75

PLAYING THE RECORDED VIDEO

Before you can play the video, you must configure the record settings. For details on record settings,

refer to “Storage”. (page 108)

Name of event search screen and its function

b c

Item Description

Search range setting

Search event setting Set the event type to search within the search period.

Set the search date and time from the data saved in the Micro SD memory card.

● WEB VIEWER

Event search Run the event search.

English _75

Page 76

web viewer

To play the content after searching by event

1. Click the [Playback ( )] button.

2. Specify the start time and end time of

your search.

3. Select an event type for your search within the specified period.

4. Click the [Event search] button. The search results will be displayed in the list.

If more than 800 events are recorded

within the search period, your search will be limited up to the date when the 800th event is recorded. For instance, if the search period is between 10th and 15th day of the month, and more than 800 events were recorded 10th through 11th, your search will be limited up to 11th day with a total of 800 events, and events after then (from 12th) will not be found.

5. Select a data item to play in the search list.

6. Click the [Play (

7. To stop playing the video, click [Stop (

8. To return to the search screen, click [Exit (

)] button.

)].

76_ web viewer

Page 77

Name of time search screen and its function

c d e f g h

Item Description

Time bar The section in the specific period is played by moving the time bar.

Search date setting

Screen optimization The camera image is converted to fit the Web browser window.

Fix the resolution

Full screen The current image is converted to cover the maximum size of the monitor.

Set the search date using the calendar.

Dates for which there is video in the Micro SD memory card are

displayed within the boxes on the calendar.

Regardless of the resolution setup configured in the camera, it sets the resolution to 800x600. Press it again to switch back to the default resolution.

● WEB VIEWER

Capture The current image is saved as a .jpg or .bmp image file.

Video information Time data of the replayed video is displayed on the screen.

Backup

Time zone is set to back up the video saved in the Micro SD memory card.

Can be set as up to 5 minutes.

English _77

Page 78

web viewer

To play after searching by time

1. Click [Time Search ( )].

2. Click a desired date in the calendar.

The video on the specified date will be played.

3. If the video playback is stopped, select a time and click [Play ( The video on the selected time will be played.

4. While the video is being played, the recording time for the current video will be shown.

5. Search for the video forward or backward, and control the play speed.

- How to Control the Play Interval : Select this button to move 1 frame forward. : Select this button to move 1 second back.

- To control the play speed

If selecting ), the button will switch to x1, x2, x4, x8, and the play speed will increase accordingly. When the ( button is selected, the playing speed is decreased to -1x, -2x, -4x, -8x and the playing speed slows down gradually. Subsequently the quick playing speed is returned to the normal speed and the reverse playing speed increases.

- To control the playback direction

If you see the ) button with the play speed displayed, the video will be played forward; Whereas, if you see the ( button with the play speed displayed, the video will be played backward.

6. Move [Time bar (

The time containing a normal recoding file will be highlighted in blue; the time with the event recording will be highlighted in red.

)].

)] to a desired time point of the video before playing it.

78_ web viewer

Page 79

To back up the searched video

1. During playback, click [ ] on the

scene to back up. The scheduling window for backup start and end time appears.

2. Click [

The Save As window appears.

3. Confirm the save path and click [Save]

button. The screenshot will be backed up to the specified path.

] button.

To play the backup video

The backed up images are saved in an .avi format. Gom Player, VLC Player, and Window Media Player are recommended as the media player compatible with this format.

In case of Windows Media Player, download the latest codec from www.windows7codecs.com

and install it prior to use.

● WEB VIEWER

English _79

Page 80

web viewer

To Play an AVI File

The AVI file does not contain the recording time data.

1. Separate the micro SD memory card from the camera.

Before separating the micro SD memory card, set the <Device> to <Off> in the “Setup 

Event

Storage” menu.



2. Insert the micro SD memory card into the PC.

3. Play the AVI file in the “\ch00\img\ YYYY_MM_DD” directory, using a

media player.

The file name begins with “01.avi” and

the file number increments by 1.

Once corrupted, the data in the micro SD

memory card cannot be replayed in Web Viewer Playback.

80_ web viewer

Page 81

setup screen

SETUP

You can configure the video & audio, network, event and system settings of the camera in the network.

)

(

]

1. In the Live screen, click [Setup

2. The Setup screen appears.

Microsoft Silverlight 5.0 or higher is required to be installed on the PC for setup pages that provide

preview video. If not installed already, automatically moves to the Silverlight setup.

VIDEO & AUDIO SETUP

Video profile

1. From the Setup menu, select the

<Video & Audio ( )> tab.

2. Click <Video profile>.

3. Set the <Video profile connection

policy>.

• Keep connection when profile setting is changed : Changing profile properties that is used by existing connection does not affect such connection and remains with old profile setup. If not selected, changing a profile used by an existing connection resets such connection.

4. Select each profile properties. For more details, refer to “To Add/

Change the Video Profile”. (Page 83)

5. Click the input box of each item and

enter / select a desired value.

The context menu may differ depending on

the selected codec type.

• Default profile : If no profile is selected when using the Web Viewer, the default video profile is applied.

● SETUP SCREEN

English _81

Page 82

setup screen

• E-mail/FTP profile : Video profile to be transferred to the specified email or FTP site.

Only the MJPEG codec can be set as the E-mail/FTP profile.

• Record profile : This is the profile that is applied to video recording.

• Audio-In : Sets whether to use audio for video recordings.

6. According to your situation, set ATC (Auto Transmit Control) mode.

• ATC mode : It adjusts the video properties according to the variance in the network bandwidth, controlling the bit rate. Adjusting the bit rate depends on the ATC mode.

- Control framerate : Reduce the frame rate if the network bandwidth drops down.

- Control compression : Control the compression rate if the network bandwidth drops down. Compression adjustment can cause deterioration of the image quality.

If <Bitrate control> is set to <CBR>, the encoding priority according to the ATC mode will be

fixed as below:

Bitrate control / ATC mode Control framerate Control compression

CBR Framerate Compression

• ATC sensitivity : Affect the transfer rate according to the variance in the network bandwidth. The transfer rate will be adjusted to the fastest if the bandwidth is <Very high>, and adjusted to the latest if the bandwidth is <Very low>.

• ATC limit : If the quality or frame rate is adjusted, the property will be changed to the applied value (%) against the previous setting value (100%). Note that if you reduce the property value too much, you may encounter flickering on the screen. So it is advisable to adjust the value within the threshold.

It is recommended to apply ATC control only for cameras supporting ATC.

Set the ATC sensitivity to <Very low> in a network environment with high variance in the network

bandwidth.

If the network connection is unstable, you may encounter flickering on the screen.

7. Select Able or Disable for the Crop Encoding function. For more details, refer to “To Use Crop Encoding”. (Page 85)

• Crop encoding : It cuts only the selected area out of the full screen and outputs it

at the resolution specified in <Profile setting>. The resolution should be less than the Crop Encoding setting area.

8. When done, click [Apply (

82_ setup screen

)].

Page 83

To Add/Change the Video Profile

The profile setup can be added or modified to accommodate various profiles depending on the recording conditions.

1. Select one from the <Video profile> options.

2. Provide the name and select a codec.

3. Specify the conditions under which the codec will be applied.

4. Specify the details of the selected codec including resolution and frame rate.

Click <Advanced> to display the context menu.

• Resolution : Set the video size of the H.264 and MJPEG files.

• Framerate : Specify the frame rate.

The <Sensor> mode setup in Camera Setup changes the maximum configurable framerate.

Sensor 25 fps 30 fps 50 fps 60 fps

Framerate 1~25 fps 1~30 fps 1~50 fps 1~60 fps

• Compression : Specify the compression rate of the video.

• Maximum bitrate : Specify the maximum bit rate of the video.

As the bit rate can be adjusted limitedly according to the resolution, frame rate and screen

complexity, the actual bit rate can be greater than the maximum bit rate. So you must consider the use conditions when setting the value.

• Bitrate control : You can select one from constant bit rate and variable bit rate for compression. Constant bit rate (CBR) varies the video quality and fixes network transfer bit rate, while variable bit rate emphasizes the quality by varying network transfer bit rate.

If the bit-rate control is set to the Constant Bit Rate, the actual transmission frame rate

may be less than the set frame rate because the Frame Rate First Mode is changed to the Compression Rate First Mode to ensure the highest image quality at a bit rate which is set depending on the complexity of the screen.

● SETUP SCREEN

English _83

Page 84

setup screen

• Encoding priority : You can set the video transfer method to Framerate or Compression.

• GOV length : It specifies the distance (in terms of number of frames) between two consecutive I-Frames in a video sequence when H.264 codec was selected. (One I-Frame + 0~Several P-Frames)

• Profile : You can select the H.264 profiling method.

• Entropy coding : Reduce the possible compression loss due to encoding.

• Multicast (SVNP) : Specify the use of the SVNP protocol.

- IP address : Enter an IPv4 address with which you can connect to the IPv4 network.

- Port : Specify the video communication port.

- TTL : Set the TTL for the SVNP packet.

• Multicast (RTP) : Specify the use of the RTP protocol.

- IP address : Enter an IPv4 address with which you can connect to the IPv4 network.

- Port : Specify the video communication port.

- TTL : You can set the TTL for the RTP packet.

What is GOV length?

GOV(Group of Video object planes) is a set of video frames for H.264 compression, indicating a collection of frames from the initial I-Frame (key frame) to the next I-Frame. GOV consists of 2 kinds of frames: I-Frame and P-Frame.

I-Frame is the basic frame for the compression, also known as Key Frame, which contains one complete image data. P-Frame contains only the data that has changed from the preceding I-Frame.

For H.264 codec, you can determine the GOV length.

84_ setup screen

Page 85

To Use Crop Encoding

1. Select <Use>.

2. Click <Set area>.

The Crop Encoding Area Setup window will pop up.

3. Select <Ratio>.

• Ratio: It sets up the aspect ratio of the user specified area.

- 16:9 : The aspect ratio shall be set to 16:9 as close as to the user specified area. The supporting size ranges from 426X240 to 1280X1024 and supporting output resolutions are 320X180, 640X360, 800X450, and 1280X720.

- 4:3 : The aspect ratio shall be set to 4:3 as close as to the user specified area. The supporting size ranges from 320X240 to 1280X960 and supporting output resolutions are 320X240, 640X480, 800X600, 1024X768, and 1280X960.

- Manual : It sets up the aspect ratio of the user specified area. The supporting size ranges from 320X240 to 1280X1024 and all supporting output resolutions are available except 1920X1080.

4. Drag the mouse on the screen to specify the Crop Encoding area at your discretion.

If set to <Manual>, the output image may be different from the actual one because of the aspect

ratio inconsistency between the Crop Encoding area and the output resolution.

The Crop Encoding area setup can change depending on the DIS setup. Reset the Crop Encoding

area when the DIS setup is changed.

● SETUP SCREEN

English _85

Page 86

setup screen

Video setup

1. From the Setup menu, select the <Video & Audio ( )> tab.

2. Click <Video setup>.

3. Select a <Video source> mode.

• Flip mode : Turn upside down the image that is captured by the camera.

• Mirror mode : Flip horizontal the image that is captured by the camera.

4. Select Able or Disable for the analog

video output.

5. Select the video type.

6. Specify the privacy zone.

7. When done, click [Apply (

To set the privacy zone

You can specify a certain area of the camera video to be protected for your privacy.

1. Set it to <On>.

2. When done, click [Apply (

3. Select 4 vertices on the screen with

your mouse to specify the area.

4. Enter the name and select the color, and then click [OK].

5. If you want to delete an area in the list, select one and click [Delete (

)].

86_ setup screen

Page 87

Audio setup

You can configure the I/O settings of the audio source from the camera.

1. From the Setup menu, select the

<Video & Audio (

2. Click <Audio setup>.

3. Set the audio input value.

• Source : Sets the audio input.

- Line : Connect the cable to the audio device.

- Internal microphone : Microphone that is built-in in the camera. (It is applicable only to the SND-6084R model.)

- External microphone : 3.5mm jack type, powered active external microphone.

• Apply power to Ext. Mic. : If the external microphone connected has no separate power supply, check this option to set camera to supply power to the connected external microphone. The option is enabled if <External microphone> is selected.

• Codec : Specify the audio codec.

- G.711 : A audio codec standard, it uses 64 Kbps PCM (Pulse Code Modulation) encoding. ITU standard audio codec that is adequate for digital voice transfer in PSTN network or through a PBX.

- G.726 : ITU standard audio codec applying ADPCM (Adaptive Differential Pulse Code Modulation) for variable bit rates of 40/32/24/16 Kbps to 64 Kbps PCM encoding.

• Bitrate : Set the bit rate to differentiate compression ratio if using G.726 codec.

• Gain : Specify the audio input amplification.

Sound quality deterioration or howling may occur if the loudness of the sound source or gain value

were set excessively.

)> tab.

● SETUP SCREEN

4. Set the audio output level.

• Enable : Sets whether to use audio output.

• Gain : Specify the audio output amplification.

5. When done, click [Apply (

)].

English _87

Page 88

setup screen

Camera setup

You can change the camera settings according to the environment where the camera is located.

1. From the Setup menu, select the <Video & Audio (

2. Click <Camera setup>.

Configure the settings as necessary of :

Sensor, SSDR, White balance, Back light, Exposure, Day/Night, Special, OSD, IR

4. When done, click [Apply ( )].

If a certain time (timeout: 240s) is elapsed

your not pressing the [Apply ( button after changing the settings, your changes will not be applied.

To Set the Sensor

It specifies how many frames the camera CMOS sensor will capture per second.

1. Select <Sensor>.

2. Select <Mode>.

Refer to “Video profile” for the framerate

setup range of the <Video profile> according to mode setup. (Page 81)

If the sensor mode is set to 50 fps or 60 fps, the <Back light> mode cannot be set to <WDR>.

)> tab.

with

)]

88_ setup screen

Page 89

To Set SSDR (Samsung Super Dynamic Range)

In a scene where the difference between bright and dark is severe, you can increase the brightness of the dark area alone to regulate the overall brightness.

1. Select <SSDR>.

2. Set <Mode> to <On>.

3. Configure the <Level> and <D-Range>

settings as necessary.

• Level : Adjust the level of the dynamic range.

• D-Range : Select the amplitude area of the dynamic range.

To Set White Balance

You can correct the image colors based on white under any lighting conditions.

1. Select <White balance>.

2. Select <Mode>.

• ATW : Corrects the colors of the camera video automatically.

• Manual : You can adjust the red and blue gains of the camera video manually.

• AWC : Corrects the colors of the camera video to be optimized to the current lighting condition and screen mode. To obtain the optimal condition for the current lighting, put the focus of the camera to a white paper and press the [Set AWC] button. If the lighting environment is changed, you should readjust the settings accordingly.

• Outdoor : Automatically corrects the video colors of the camera to be optimized to the outdoor environment.

• Indoor : Automatically corrects the video colors of the camera to be optimized to the indoor environment.

In AWC mode, click the [Set AWC] button if you want to keep the white balance level of the

current image.

● SETUP SCREEN

The white balancing may not work properly in the following conditions:

If this is the case, switch to AWC mode.

If the surrounding condition of the object is out of the temperature correction range

ex) Clear sky, sunset If the surrounding of the object is dark

If the focus of the camera directly faces the florescent lighting or if the camera is installed in a

place of variable illumination, the white balancing operation may be unstable.

English _89

Page 90

setup screen

To Set BLC

You can specify a desired area on the video manually and set the area to be displayed more clearly.

1. Select <Back light>.

2. Set <Mode> to <BLC>.

3. Set <BLC level>.

You can change the level to adjust the brightness of the monitoring area.

4. Set the <Top, Bottom, Left, Right>

levels to specify the target area.

When BLC is set, the green box is displayed on the screen for 15 seconds.

To prevent malfunction at the time of BLC setup, the vertical space of the BLC area should be over

40 and below 60 while the horizontal space over 30 and below 60.

To Set WDR

It displays a sharp image of the objects in a scene where both bright and dark areas exist.

1. Select <Back light>.

2. Set <Mode> to <WDR>.

3. Specify the <WDR level>.

It is recommended to use WDR in the

indoor environment.

Noise may exist between the dark area

and the bright area in the WDR mode.

If the <Back light> mode is set to <WDR>, the sensor mode cannot be set to 50 fps or 60 fps.

The maximum and minimum shutter values are initialized whenever you turn on or off the WDR

mode.

90_ setup screen

Page 91

To Set Exposure

You can adjust the exposure level of the camera.

1. Select <Exposure>.

2. Select each item and set it properly.

• Brightness : Adjust the screen brightness.

• Minimum shutter : The limit of the longest exposure time.

Shutter is the mode to set up the range of

the sensor exposure time which will specify the upper and lower limits for the electronic shutter movement.

The framerate may be reduced in the dark condition if Shutter has a lower value than specified in

the Sensor mode.

• Maximum shutter : The limit of the shortest exposure time.

• Anti flicker : It prevents screen flickering incurring from the dissonance between the surrounding lighting and the frequency.

• SSNR : Select Able or Disable for the video noise elimination function.

• SSNR level : Adjust the noise reduction level.

• Iris : You can set the camera iris to Auto or Manual to your preference.

- Auto : The iris is automatically adjusted to the amount of the surrounding light.

- Manual : Sets the iris F-No to manual.

• Iris F-No : Set up the F value of the iris.

• AGC : Select AGC Control mode. Adjust the gain value of the video (that, in particular, was recorded at a low contrast scene and had a lower brightness level than normal) to control the video brightness.

The image exposure can be saturated depending on the Shutter setup range.

● SETUP SCREEN

English _91

Page 92

setup screen

To Set Day/Night

1. Select <Day/Night>.

2. Select each item and set it properly.

• Mode: Mode is used to adjust the color of Color or Black and White.

- Color : The video is always output in color.

- B/W : The video is always output in black and white.

- Auto : Normally, it is set to Color but to B&W under low luminance at night.

If AGC of the <Exposure> menu is set to <Off>, the day/night mode cannot be set to <Auto>.

- External : It controls the color of the video when the alarm input terminal is synchronized with an external device.

- Schedule : Set the time during which the camera is operated in the color mode.

• Dwell time : It specifies the period for which the selected brightness condition must be maintained to switch the lighting mode from Day to Night or vice versa.

• Duration : It specifies the interval of lighting mode conversion.

• Alarm in : The video is set to Color or B/W as the alarm sensor is open or closed.

If the Day/Night mode is set to External Input, the alarm input function of the Event-Alarm Input

page is disabled.

• Activation time(Color) : It specifies the schedule for color mode operation.

If it is set, the Color mode is maintained from 00 second of the starting time to 59 second of the

ending time.

92_ setup screen

Page 93

To Setup Special

1. Select <Special>.

2. Select each item and set it properly.

• Sharpness Mode : Adjust the overall sharpness of the image. If selecting <On>, you can adjust the sharpness of the image.

• Sharpness level : The higher the level is, the sharper and clearer the outline of the image becomes.

• Gamma : Adjust the contrast of the image.

• Color level : Adjust the strength of video color.

• Defog : Compensate the video in the foggy or cloudy weather. It is set to <Off> as a default. Specials are used when the video looks blurry in the foggy weather.

- Off : Disable the fog elimination function.

- Auto : The image is automatically compensated according to the foggy level.

Adjust <Defog level> to be more effective.

- Manual : The user manually sets the amount of compensation for each image.

If the defog mode is set to <Auto>, the performance is proportional to the fog level. To keep

the set defog level without regard to the fog level, set the defog mode to <Manual>.

If the manual defog level is high in a thin fog, the image may become too dark.

• Defog level : Control the defog level.

• DIS : Compensates the image automatically when it is seen to shake for stable image output.

Mitigate the degree of image vibration when the camera vibrates due to the external factors

such as wind.

● SETUP SCREEN

English _93

Page 94

setup screen

To Set OSD

1. Select <OSD>.

2. Select each item and set it properly.

• Title overlay : It specifies if the camera name shall be displayed on the screen.

• Camera title : It specifies the name of the camera to be displayed on the screen.

• Title position X, Y : It specifies the position of the camera name on the screen.

• Time display : Specify the use of time display on the screen.

• Date notation : Specify the date format that will be displayed on the screen.

• Time position X, Y : Specify the position of time display on the screen.

• Weekday overlay : Specify the use of date display date on the screen.

• Size : It specifies the size of the text displayed on the screen.

The OSD size and position may be automatically adjusted to the video output resolution.

To Set IR

1. Select <IR>.

2. Select each item and set it properly.

• Mode : When the IR indicator turns on in B/W mode, the screen will be protected from saturation on the center area so that you can identify a short-distant object.

- Off : IR mode will be disabled.

- Auto : Adjust the IR brightness according to the brightness of the object on the center screen.

- Manual : Adjust the IR brightness manually.

• Level : If you set IR mode to Manual, you can adjust the brightness level of the IR indicator to between 1 and 99.

94_ setup screen

Page 95

Focus setup

You can adjust the focus and zoom ratio of video image.

1. From the Setup menu, select the <Video & Audio (

2. Click <Focus setup>

3. Set the focus and zoom.

• Focus : Manually adjusts the lens focus (Far  Near).

• Zoom : Manually adjusts the zooming (Wide  Tele).

• Simple focus : Click [ the focus automatically.

The Simple focus mode may not fit correctly in the following cases:

Sudden change to the object in Simple focus mode (sudden movement, appearance or

disappearance) Radical change to the brightness in Simple focus mode

Image of a low contrast

If the camera is exposed to a strong light source in the front or surroundings

In case the focus is inappropriate apart from mentioned above, use [ , , , ,

, ] button to manually adjust the focus.

In a situation where Simple focus is hardly applied, try to use the manual focus mode.

)> tab.

] button to fit

● SETUP SCREEN

English _95

Page 96

setup screen

NETWORK SETUP

Interface

1. From the Setup menu, select the <Network ( )> tab.

2. Click <Interface>.

3. Set the <Interface> and <IPv6 setup>

as necessary.

• IP type : Select an IP connection type.

- Manual : Specify the IP address, Subnet mask, Gateway, DNS1, and DNS2.

- DHCP : Specify the DNS1 and DNS2.

- PPPoE : Specify the DNS1, DNS2, ID and Password.

If you set it to <Manual>, you should specify the IP, Subnet mask, Gateway, DNS 1 & 2 manually.

• MAC address : Shows the MAC address.

• IP address : Displays the current IP address.

• Subnet mask : Displays the <Subnet mask> for the set IP.

• Gateway : Displays the <Gateway> for the set IP.

• DNS1/DNS2 : Displays the DNS(Domain Name Service) server address.

4. Set the <IPv6 setup>.

Set to <Use> to use IPv6 address.

• Default : Use the default IPv6 address.

• DHCP : Display and use the IPv6 address obtained from the DHCP server.

• Manual : Enter IP address and gateway manually and use it.

5. When done, click [Apply (

)].

The IP addressing system will be defaulted to DHCP. If no DHCP server is found, the previous

settings will be restored automatically.

Once completed with editing, click [Apply ( )] to apply changes and the browser exits.

After a while, connect again with the changed IP.

96_ setup screen

Page 97

Port

1. From the Setup menu, select the <Network ( )> tab.

2. Click <Port>.

3. Type in each item in the Port menu as

necessary.

Neither the port range between 0 and 1023

nor port 3702 is available.

• HTTP port : HTTP port used to access the camera via the web browser. The default is 80(TCP).

Setting the HTTP port for Safari and Google Chrome browsers to 65535 is not allowed by security

policy.

• Device port : Set a port used to transfer video signals with the Samsung protocols.

• RTSP port : Used to transfer videos in the RTSP mode; the default is 554.

• Web streaming port : Used to transfer videos to the Web Viewer; the default is 4520.

• Silverlight policy port : Silverlight is used to permit to acquire a network connection; the default is 943.

If changed the HTTP port, the browser exits.

Afterwards, address should contain the newly assigned HTTP port trailing the IP. ex) IP address: 192.168.1.100, HTTP port : Assigned 8080  http://192.168.1.100:8080 (If HTTP port is set to 80, no need to specify the port number)

The port range of the Web Streaming is between 4502 and 4534. If the Device port is with this

effective range, the Web Streaming port should be specified the same as the Device port.

You cannot change the Web Streaming/Silverlight policy server port of a camera.

4. When done, click [Apply (

)].

● SETUP SCREEN

English _97

Page 98

setup screen

DDNS

DDNS is an abbreviation of Dynamic Domain Name Service that converts the IP address of a camera into a general Host Name so that the user can easily remember it.

1. From the Setup menu, select the <Network (

2. Click <DDNS>.

3. Select the <DDNS> connection type.

4. Type in the DDNS items according to

the selected type.

• Samsung DDNS : Select this if you use the DDNS server provided by Samsung Techwin.

- Product ID : Enter the product ID that is registered with the Samsung DDNS service.

- Quick connect : It sets port forwarding automatically when used with a UPnP (Universal Plug and Play) supporting router.

• Public DDNS : Select one of provided public DDNS servers when you use a public DDNS server.

- Service : Select desired public DDNS service server.

- Host name : Enter the name of the host that is registered with the DDNS server.

- User name : Enter the user name for the DDNS service.

- Password : Enter the password for the DDNS service.

5. When done, click [Apply (

)> tab.

)].

If selected <Quick connect>, be sure to select Samsung DDNS service.

98_ setup screen

Page 99

Registering with DDNS

To register your product with the Samsung DDNS

1. Visit the iPOLiS web site

(www.samsungipolis.com) and sign in with a registered account.

2. From the top menu bar, select <DDNS SERVICE> - <MY DDNS>.

3. Click [PRODUCT REGISTRATION].

4. Enter the product ID.

You must perform the duplicate check for the

ID that you entered.

5. Select a <CLASSIFICATION> and specify the <MODEL NUMBER>.

6. Specify the product location with a description if necessary.

7. Click [REGISTRATION]. The product will be added to the product list that you can check.

● SETUP SCREEN

English _99

Page 100

setup screen

To connect to the Samsung DDNS in camera setup

1. From the DDNS setup page, set <DDNS> to <Samsung DDNS>.

2. Provide the <Product ID> that you

registered product ID with the DDNS site.

3. Click [Apply ( When the connection is successfully made, you will see the message of <(Success)> on the screen.

Configuring public DDNS in Camera Settings

1. Open the DDNS settings page and select <Public DDNS> for <DDNS>.

2. Enter the corresponding site’s host name, user name and password.

3. Click [Apply ( If the connection properly establishes, <(Success)> appears.

4. When done, click [Apply (

To use DDNS service properly, both DDNS setup and the router’s port forwarding setup are

required. For port forwarding setup, refer to “Port Range Forward (Port Mapping) Setup”. (page 60)

)].

)] button.

)].

100_ setup screen