SAMSUNG LTM215HT03 Specification

Global LCD Panel Exchange Center

www.panelook.com

Approval Specification

Customer : Dell / Qisda

SAMSUNG TFT--

SAMSUNG TFT

SAMSUNG TFT-LCD PRODUCT INFORMATION

MODEL : LTM215HT03

Any Modification of Specification is not allowed without SEC's Permission.

NOTE : Spec for E2211H

LCD PRODUCT INFORMATION

DATE : 15 / July / 2010

PREPARED BY

Customer’’

Customer

SIGNATURE

s Approval

DATE

APPROVAED BY

Application Engineering Part 3, TCS team

LCD Division, Samsung Electronics Co. , LTD.

DATE

15/July/’10

DATE

15/July/’10

1/39Page05-000-S-100715Doc. NoLTM215HT03MODEL

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

Contents

Product Configuration Approval Sheet ---------------------------------------------------------- (3)

Revision History --------------------------------------------------------------------------------------- (4)

General Description -------------------------------------------------------------------------------- (5)

1. Absolute Maximum Ratings ------------------------------------------------------------------- (6)

2. Optical Characteristics -------------------------------------------------------------------------- (8)

3. Electrical Characteristics ------------------------------------------------------------------------(13)

3.1 TFT LCD Module

3.2 Back Light Unit

www.panelook.com

Approval Specification

4. Block Diagram ----------------------------------------------------------------------------------- (17)

4.1 TFT LCD Module

4.2 Back Light Unit

5. Input Terminal Pin Assignment -------------------------------------------------------------- (18)

5.1 Input Signal & Power

5.2 LVDS Interface

5.3 Back Light Unit

5.4 Input Signals, Basic Display Colors and Gray Scale of Each Color

6. Interface Timing --------------------------------------------------------------------------------- (27)

6.1 Timing Parameters (DE only mode)

6.2 Timing Diagrams of interface Signal (DE only mode)

6.3 Power ON/OFF Sequence

6.4 VDD Power Dip Condition

7. Outline Dimension ------------------------------------------------------------------------------- (31)

8. Reliability Test ------------------------------------------------------------------------------------ (33)

9. Packing -------------------------------------------------------------------------------------------- (34)

10. Marking & Others -------------------------------------------------------------------------------(35)

11. General Precaution ---------------------------------------------------------------------------- (37)

11.1 Handling

11.2 Storage

11.3 Operation

11.4 Operation Condition Guide

11.5 Others

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

2/39Page05-000-S-100715Doc. NoLTM215HT03MODEL

www.panelook.com

Global LCD Panel Exchange Center

Product Configuration Approval Sheet

Description

Date of Approval

www.panelook.com

LTM215HT03Product Name

Approval Specification

ContentItems

Dell / QisdaCustomer

E2211HProject Name

Customer System Configuration

Scaler

LED Driver

Input Interface

ContentItems

E2211HSystem Name

Standard MNTPurpose

TSUMU58NHJ – LF – 3

OZ9998A

AC100~120V / AC200~240·10% , 50/60HzPower

VGA / DVI

-OS

-Graphic Card

Notice : SEC product approval spec guarantee a above customer system.

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

3/39Page05-000-S-100715Doc. NoLTM215HT03MODEL

www.panelook.com

Global LCD Panel Exchange Center

* Revision History

www.panelook.com

Approval Specification

Date

2010

Rev.

SummaryPage

Approval specification of LTM215HT03 model was issued first.All000July 15,

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

4/39Page05-000-S-100715Doc. NoLTM215HT03MODEL

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

General Description

Approval Specification

Description

LTM215HT03 is a color active matrix liquid crystal display (LCD) that uses amorphous silicon TFT (Thin Film Transistor) as switching components. This model is composed of a TFT LCD panel, a driver circuit and a back light unit. The resolution of a 21.5” is 1920 x 1080 and this model can display up to 16.7 millions colors.

Features

 High contrast ratio, high aperture structure  High speed response  FHD (1,920 x 1,080 pixels) resolution  White LED Edge slim Backlight ( 1-side )  Low power consumption  DE (Data Enable) only mode  LVDS (Low Voltage Differential Signaling) interface (2pixel/clock)  RoHS compliance 

TCO 5.0 compliances

( Except for 2.2 response time; this product does not have over driving function.

It is recommended to support in system level )

 Halogen Free

Applications

 Multi-functional monitor products  Display terminals for AV application products  Monitors for industrial machine

* If the module is used to other applications besides the above, please contact SEC

in advance.

General Information

Haze 25% , Hard coating (3H)Surface Treatment

UnitSpecificationItems

um248.25(H) x 248.25(W)Pixel Pitch

mm476.64(H) x 268.11(V)Active Display Area

colors16.7M [Hi-FRC]Display Colors

pixel1,920 x 1,080Number of Pixels

RGB vertical stripePixel Arrangement

Normally WhiteDisplay Mode

Note

cd/༇250(Typ.)Luminance of White

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

5/39Page05-000-S-100715Doc. NoLTM215HT03MODEL

www.panelook.com

Global LCD Panel Exchange Center

Mechanical Information

www.panelook.com

Approval Specification

Max.

496.1

mm495.6495.1Horizontal (H)

NoteUnitTyp.Min.Item

Module

292.7

mm292.2291.7Vertical (V)

size

12.0

1,900

mm--Depth (D)

Partially 12.3mm in the circuit area.

Refer to the page 30.

LCD module onlyg--Weight

Note (1) Mechanical tolerance is · 0.5mm unless there is a special comment.

1. Absolute Maximum Ratings

If the condition exceeds maximum ratings, it can cause malfunction or unrecoverable damage to the device.

Power Supply Voltage

Data Signal

Storage temperature

Center of Glass surface temperature

(Operation)

Shock ( non - operating )

Vibration ( non - operating )

Note (1) Ta= 25 · 2 ¶C

sig

STG

OPR

nop

NoteUnitMax.Min.SymbolItem

(1)V6.5GND-0.5V

V5-V

60-25T

500T

୅

(2)

(3)(5)G50-S

(4)(5)G1.5-V

6/39Page05-000-S-100715Doc. NoLTM215HT03MODEL

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

(2) Temperature and relative humidity range are shown in the figure below.

a. 90 % RH Max. (Ta ˺ 39 ¶C) b. Maximum wet-bulb temperature at 39 ¶C or less. (Ta ˺ 39 ¶C) c. No condensation

(3) 11ms, sine wave, one time for ·X, ·Y, ·Z axis (4) 10-300 Hz, Sweep rate 10min, 30min for X,Y,Z axis (5) At vibration and shock test, the fixture which holds the module to be tested has to be

hard and rigid enough so that the module would not be twisted or bent by the fixture.

www.panelook.com

Approval Specification

(39,90)

(50,50.4)

25,5)

((--25,5)

Fig. Temperature and Relative humidity range

(60,27.7)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

7/39Page05-000-S-100715Doc. NoLTM215HT03MODEL

www.panelook.com

Global LCD Panel Exchange Center

2. Optical Characteristics

The optical characteristics should be measured in a dark room or equivalent.

Measuring equipment : SR-3, RD-80S (TOPCON), EZ-Contrast (Eldim)

( Ta = 25 · 2¶C, VDD=5V, fv= 60Hz, fDCLK=67.3MHz, If= 252mA )

www.panelook.com

Approval Specification

NoteUnitMax.Typ.Min.ConditionSymbolItem

Contrast Ratio

(Center of screen)

Response

Time(On/Off)

Luminance of White

(Center of screen)

Color

Chromaticity

(CIE 1931)

Red

Green

Blue

White

Red

-1000600C/R

105-Tr + TfOn/Off

0.639

0.340Ry

0.324Gx

0.622Gy

-0.030

0.155Bx

Normal

L,R

U,D

Viewing

Angle

0.042By

0.313Wx

0.329Wy

-250200Y

+0.030

-0.441-Ru'

-0.527-Rv'

msec

cd/m

(3)

SR-3

(5)

RD-80S

(6)

SR-3

(7),(8)

SR-3

-0.132-Gu'

Color

Chromaticity

(CIE 1976)

C.G.L

(ACC ONLY)

* C.G.L : Color Grayscale Linearity

Green

-0.570-Gv'

-0.194-Bu'

Blue

-0.118-Bv'

-0.198-Wu'

White

-0.468-Wv'

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

(9)0.02--Ƹu'v'White

8/39Page05-000-S-100715Doc. NoLTM215HT03MODEL

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Approval Specification

NoteUnitMax.Typ.Min.ConditionSymbolItem

%-72--Color Gamut

K-6500--Color Temperature

Hor.

Viewing

Angle

Ver.

Brightness Uniformity

(9 Points)

uni

Note (1) Test Equipment Setup

The measurement should be executed in a stable, windless and dark room between 30min after lighting the back light at the given temperature for stabilization of the back light. This should be measured in the center of screen.

LED forward current : If = 252 mA Environment condition : Ta = 25 · 2 ¶C

Field Photo detector

CR˻10

Photo detector

-8570

-8570 Degrees

-8070

%25--B

(8)

EZ-

Contrast

(4)

SR-3

2ദSR-3

TFT - LCD Module

Field

SR-3 : 40໅ RD-80S : 50໅

LCD Panel

The center of the screen

9/39Page05-000-S-100715Doc. NoLTM215HT03MODEL

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

Note (2) Definition of test point

www.panelook.com

192 960 1728

Approval Specification

Active Area

: Test Point

Note (3) Definition of Contrast Ratio (C/R)

: Ratio of gray max (Gmax) & gray min (Gmin) at the center point㽶 of the panel

3 2 1

Gmax : Luminance with all pixels white Gmin : Luminance with all pixels black

Note (4) Definition of 9 points brightness uniformity

Buni

(max min)

100



max

8 79

max

min

108

540

972

Bmax : Maximum brightness Bmin : Minimum brightness

Note (5) Definition of Response time : Sum of Tr, Tf

Display Data White(TFT off) Black(TFT on) White(TFT off)

Optical Instruments

Response

100%

90%

10%

10/39Page05-000-S-100715Doc. NoLTM215HT03MODEL

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

Note (6) Definition of Luminance of White : Luminance of white at center point㽶

Note (7) Definition of Color Chromaticity (CIE 1931, CIE1976)

Color coordinate of Red, Green, Blue & White at center point㽶

Note (8) Definition of Viewing Angle

: Viewing angle range (CR ˻ 10)

www.panelook.com

Approval Specification

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

11/39Page05-000-S-100715Doc. NoLTM215HT03MODEL

www.panelook.com

Global LCD Panel Exchange Center

Note (9) Color Grayscale Linearity

a. Test image : 100% full white pattern with a test pattern as below

b. Test pattern : Squares, 40mm by 40mm in size, filled with 255, 225, 195, 165, 135 and

105 grays steps should be arranged at the centerྜྷ of the screen.

www.panelook.com

Approval Specification

c. Test method

-1

gray step : move a square of 255 gray level should be moved into the center of the

screen and measure luminance and u’ and v’ coordinates.

- Next gray step : Move a 225 gray square into the center and measure both luminance and coordinates, too.

d. Test evaluation

'u' v'= (u' - u' ) + (v' - v' )AB

Where A, B : 2 gray levels found to have the largest color differences between them

i.e. get the largest ȟu’ and ȟv’ of each 6 pair of u’ and v’ and calculate the ȟu’v’.

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

12/39Page05-000-S-100715Doc. NoLTM215HT03MODEL

www.panelook.com

+ 27 hidden pages