SAITEK Pro Flight Yoke User Manual

Pro Flight Yoke System

User Guide

Saitek

PZ45_Pro Flight yoke_QSG2.qxd 05/09/2007 09:55 Page 1

2 3

Chronograph: Accurate time and stopwatch function to time each leg of your flight. Display also indicates which programming mode is selected.

8-way point of view hat switch 2-way rocker switch Single function button (back of left handle)

2-way rocker switch

(point to both switches)

Single function button

3 position Mode switch (back of

right handle)

SAITEK PRO FLIGHT YOKE SYSTEM

Congratulations on buying the Saitek Pro Flight Yoke System. The Pro Flight Yoke features realistic controls configurable for all the major flight simulation software to make your flying experiences more realistic.

Installing the flight yoke and throttle quadrant

First, fix the Flight Yoke to your table or desk by inserting the prongs of the mounting clamp into the holes on the Yoke base and then tightening the screw mechanism until the yoke is firmly attached (be careful not to overtighten the screw as you may damage the clamp). Next, screw the mounting plate to the Throttle Quadrant using the four screws provided. You can screw the plate to one of two sides of the quadrant depending on how you want to mount the Quadrant - either in front and below your table or on top of it. Please note that whichever way you choose to mount

Detachable lever knobs to configure any combination of throttle, flaps, mixture or prop pitch.

Smooth travel levers with 0 button detent

Three 2-way rocker switches

PZ45_Pro Flight yoke_QSG2.qxd 05/09/2007 09:55 Page 2

9. At the Registration screen, select Check this box to register now and follow the on-screen instructions, or you can choose to select this option later.

10.Click on Finish to complete the installation.

B) Drivers and Programming Software For Advanced Users Follow points 1 - 7 of the install procedure in A), then at the Software Setup screen,

select Install the SST Programming Software and click Next. In the following Software Setup screen, click Next and follow the on-screen

instructions. At this point you will be asked to install such features as the Saitek Magic Mouse, HID-compliant mouse, Saitek Magic Keyboard and HID Keyboard Device (these are what XP calls the Programming elements of your Saitek controller). Continue to click on Next and Finish to accept the installation until the Registration screen appears.

At the Registration screen, select Check this box to register now and follow the onscreen instructions, or do not select this option and register later.

Upon completion of the installation, you have the option to Run Profile Editor, which will give you a view of the programming environment. If you do not wish to see the Profile Editor at this point, just uncheck the box and click on Finish to complete the installation.

IMPORTANT INFORMATION Driver updates

From time to time there may be updates to the driver and programming software for this product. You can check for the latest software updates by visiting the Saitek website (www.saitek.com) and clicking on Downloads. A drop down menu will appear. Select Drivers and Software.

the quadrant, ensure that as you look at the unit the rocker switches are at the bottom.

Now tighten the throttle unit clamp's screw mechanism until it is firmly attached to your table. You can also position the throttle quadrant on the left or right side of the flight yoke.

Now, connect the Throttle Quadrant to back of the flight yoke with the PS/2-style connector provided.

Use the integrated USB Hub on the side of the Pro Flight Yoke to easily connect other parts of the Saitek Pro Flight range of products, such as additional Pro Flight Throttle Quadrants, Pro Flight Rudder Pedals or other peripherals.

Software installation for users of Windows® XP, XP64 and Vista

A) Drivers Only For Typical Users

1. With your computer switched on, close down any programs that are currently running and insert the Installation CD into your CD-ROM drive.

2. When the Introduction Screen appears, click Install Software to continue. If the CD does not run automatically, select Start from the Windows® Taskbar, then Run and type D:\Setup.exe and click OK - where D:\ is letter of your CD-ROM drive.

3. When the Welcome screen appears, click Next to continue.

4. After reading the Disclaimer, select the I accept the terms of the Disclaimer option and click Next to continue.

5. At the Driver Setup screen, if you haven't already done so, plug the USB cable into one of your computer's USB ports and click on Next.

6. At the Driver Setup screen, click Next to test your controller.

7. When the Saitek Controller screen appears, try out all your controller's buttons and controls to show that it is working properly. When you have finished, click OK.

8. At the Software Setup screen, select Do not install the SST Programming Software and click Next. The Programming Software can be installed at a later date by following instruction (B). below

PZ45_Pro Flight yoke_QSG2.qxd 05/09/2007 09:55 Page 4

Flight Yoke controls and corresponding functions in Microsoft Flight Simulator

Function Default function in FS 9 and FS X

Yoke axis X axis Ailerons

Y axis Elevator

Main Buttons Button 1 Brakes (apply/release)

T1 (button 3) Elevator trim down T2 (button 4) Elevator trim up T3 (button 5) Flaps retract incrementally T4 (button 6) Flaps extend incrementally T5 (button 7) Knee board display/hide T6 (button 8) Landing gear up/down Button 2 Views (cycle) POV Panoramic viewing

Other Controls Mode switch Switches Mode when using Saitek Smart

Technology (SST) programming software

Clock Buttons Function Clock / stopwatch swap

Start/Stop Start/stop stopwatch Reset Reset stopwatch

Configuring your Saitek Pro Flight Yoke and Throttle Quadrant for Microsoft Flight Simulator 9 and FS X

The Saitek Pro Flight Yoke System's buttons, controls and axes correspond to commonly used functions in Microsoft FS 9 and FS X according to the tables below. As with any software, if you wish to change the function of a button or control, you will need to change the settings of the game software.

Function Overview

Button 1 POV

T1 = Button 3 T2 = Button 4

Chronometer display

Button 2

Mode Selector

T3 = Button 5 T4 = Button 6

T5 = Button 7 T6 = Button 8

Function Stopwatch/Clock

Stopwatch Start/Stop

Stopwatch Reset

PZ45_Pro Flight yoke_QSG2.qxd 05/09/2007 09:55 Page 6

Quadrant controls and corresponding functions in Microsoft Flight Simulator

Function Default function in FS 9 and FS X

Quadrant Axis Z axis Throttle

Rx axis Flaps Ry axis Spoiler

Axis buttons Z button Assignable in game

Rx button Assignable in game Ry button Assignable in game

Toggle switches T1 (button 15) Assignable in game

T2 (button 16) Assignable in game T3 (button 17) Assignable in game T4 (button 18) Assignable in game T5 (button 19) Assignable in game T6 (button 20) Assignable in game

How to assign Pro Flight Yoke controls to Flight Simulator functions

If you wish to change the controls or set up the additional buttons that have not been assigned by Flight Simulator automatically, then you must use the Assignments (Flight Simulator 2004) or Controls (Flight Simulator X) screen within the game. This is accessed from the Settings menu within the game.

When you access the Assignments/Controls screen in Flight Simulator, ensure that the Saitek Pro Flight Yoke is selected in the option labelled Joystick Type.

If you wish to reassign any of the buttons on your controller, you must first select the Buttons/Keys tab at the top of the window.

If you wish to reassign any of the axes on your controller, (the yoke itself or the levers on the throttle quadrant) you must select Joystick Axes (Flight Simulator 2004) or Control Axes (Flight Simulator X) at the top of the window.

Once you have done this, simply find the command that you want to assign to your controller from the list of commands, click it and then click the Change Assignment

Function Overview

Rx Axis

Z Axis

Rx Button

Z Button

T1 = Button 15 T2 = Button 16

T3 = Button 17 T4 = Button 18

T5 = Button 19

Ry Button

Ry Axis

T6 = Button 20

PZ45_Pro Flight yoke_QSG2.qxd 05/09/2007 09:55 Page 8

What is a Profile?

A Profile is a custom setup for improved gameplay - consisting of a set of commands that are pre-assigned to the buttons or axes of your controller. Pre-written Profiles are available on the Product Companion Disk that accompanies this device or on the Saitek Website - www.saitek.com. (Please check the website for new or improved Profiles, which are added regularly).

How do I program my controller?

After getting to know your controller, you can start creating your own personal Profiles with the Saitek Smart Technology programming software (SST). This software has virtually unlimited programming capabilities and allows you to customize the controller to your exact gaming needs.

The Profile Editor allows you to program the buttons on your controller to perform different actions within your games - this is especially useful if the game you are using does not have its own screen that allows reconfiguring of your buttons.

Getting Started

1. Double-click on the Saitek Smart Technology icon the install left on your desktop.

2. In the Profile Editor, choose the control to which you wish to assign a keyboard command. You do this by left-clicking on the control's cell in the control list on the right of the screen.

3. With the cursor flashing, type in the key commands and then click on the green tick mark when complete.

4. Repeat this procedure for all the buttons you would like to program and then click File, Save at the top of the Profile Editor window.

5. Give the profile a name (it is recommended you name it after the game for which the profile is intended) and then click Save.

6. To enable the profile either click the blue Profile Now icon at the top of the Profile Editor or right-click on the controller icon in your taskbar and select the name of the profile from the pop-up list of options.

button. Awindow will appear asking you to move the part of your controller that you want to assign to that command - press/move the button/axis that you want to assign to that command and then click OK.

Tip: You may find that when you assign the levers on the quadrant to a command, that they don't appear to work when you test them in the game. If this happens then you must look in the Sensitivities screen (Flight Simulator 2004) or the Calibration tab of the Controls screen (Flight Simulator X) of the game, select the axis command in the list there and ensure that the Sensitivity isn't set too low (set the horizontal sensitivity slider control to around 70%).

Programming your Saitek Pro Flight Yoke and Throttle Quadrant with Saitek Smart Technology software

Introducing Saitek Smart Technology programming software

Saitek Smart Technology Programming Software (SST) is the software Saitek supplies to configure your Saitek controller for enhanced functionality. SST delivers a powerful set of features, allowing you to program your device with the ultimate configuration for total interaction. Despite a level of sophistication previously unseen in the market, and because of the Saitek Smart Technology inside, the software remains simple and intuitive to use.

For a complete guide on how to program your Saitek controller, visit the Saitek website at www.saitek.com or look at the help tab on your programming software menu.

Features of Smart Technology programming software:

• Quick and easy setup in any game

• Personalize the controller settings for your favorite games

• Configure your controller with an on-screen 3D model and interface

• Multiple setup option for each controller - ideal if a controller is used by several people and you need more than one profile per device

• Program special moves with sophisticated timing features

• Special game setups available as 'Profiles' from the Saitek website and on the Smart Technology CD

• Download the latest version of Saitek Smart Technology software from the Saitek website

PZ45_Pro Flight yoke_QSG2.qxd 05/09/2007 09:55 Page 10

any way, or the incorporation of this product into any other products, or damage to the product caused by accident, fire, floods, lightning, or acts of God, or any use violative of instructions furnished by Saitek plc.

5. Obligations of Saitek shall be limited to repair or replacement with the same or similar unit, at our option. To obtain repairs under this warranty, present the product and proof of purchase (eg, bill or invoice) to the authorized Saitek Technical Support Center (listed on the separate sheet packaged with this product) transportation charges prepaid. Any requirements that conflict with any state or Federal laws, rules and/or obligations shall not be enforceable in that particular territory and Saitek will adhere to those laws, rules, and/or obligations.

6. When returning the product for repair, please pack it very carefully, preferably using the original packaging materials. Please also include an explanatory note.

IMPORTANT: To save yourself unnecessary cost and inconvenience, please check carefully that you have read and followed the instructions in this manual.

This warranty is in Lieu of all other expressed warranties, obligations or liabilities. ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR APARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE DURATION OF THIS WRITTEN LIMITED WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. IN NO EVENT SHALL WE BE LIABLE FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANYOTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER Some states do not allow the exclusion or limitation of special, incidental or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

This symbol on the product or in the instructions means that your electrical and electronic equipment should be disposed at the end of its life separately from your household waste. There are separate collection systems for recycling in the EU. For more information, please contact the local authority or your retailer where you purchased the product.

7. You will notice that when a profile is loaded that the controller icon in your taskbar has a green square behind it, indicating that a profile is currently loaded. If you wish to unload a profile simply right-click on the controller icon and click Clear Profile from the pop-up list of options.

If you require more detailed assistance with using the SST Programming Software, click on Help at the top of the Profile Editor and then Manual.

Technical Support

Nearly all the products that are returned to us as faulty are not faulty at all - they have just not been installed properly.

If you experience any difficulty with this product, please first visit our website www.saitek.com. The technical support area will provide you with all the information you need to get the most out of your product and should solve any problems you might have.

If you do not have access to the internet, or if the website cannot answer your question, please contact your local Saitek Technical Support Team. We aim to offer quick, comprehensive and thorough technical support to all our users so, before you call, please make sure you have all the relevant information at hand.

To find your local Saitek Technical Support Center , please see the separate Technical Support Center sheet that came packaged with this product.

Conditions of Warranty

1. Warranty period is 2 years from date of purchase with proof of purchase submitted.

2. Operating instructions must be followed.

3. Specifically excludes any damages associated with leakage of batteries. Note: Batteries can leak when left unused in a product for a period of time, so it is

advisable to inspect batteries regularly.

4. Product must not have been damaged as a result of defacement, misuse, abuse, neglect, accident, destruction or alteration of the serial number, improper electrical voltages or currents, repair, alteration or maintenance by any person or party other than our own service facility or an authorized service center, use or installation of non-Saitek replacement parts in the product or the modification of this product in

PZ45_Pro Flight yoke_QSG2.qxd 05/09/2007 09:55 Page 12

FCC Compliance and Advisory Statement

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1 This device may not cause harmful interference, and; 2 This device must accept any interference received, including interference that may

cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna;

- Increase the separation between the equipment and receiver;

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected;

- Consult the dealer or an experienced radio/TV technician for help.

Saitek Industries, 2295 Jefferson Street, Torrance, CA 90501, USA

Canada ICES-003

Operation is subject to the following two conditions: 1 This device may not cause interference, and; 2 This device must accept any interference, including interference that may cause

undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

PZ45_Pro Flight yoke_QSG2.qxd 05/09/2007 09:55 Page 14

Installation von Flight Yoke und Throttle Quadrant

Befestigen Sie zuerst den Flight Yoke an Ihrem Tisch, indem Sie die Zinken der Montageklemme in die Löcher an der Flight Yoke-Basis schieben und dann den Schraubmechanismus anziehen, bis der Flight Yoke fest sitzt. (Achten Sie darauf, dass Sie die Schraube nicht zu fest anziehen, da Sie sonst die Klemme beschädigen könnten.) Dann schrauben Sie die Montageplatte mit Hilfe der vier mitgelieferten Schauben an den Throttle Quadrant. Sie können die Platte an eine der beiden Seiten des Quadranten schrauben, je nachdem, wie Sie ihn montieren wollen - entweder vor, unter oder auf

SAITEK PRO FLIGHT YOKE SYSTEM

Herzlichen Glückwunsch zum Kauf des Saitek Pro Flight Yoke System. Das Pro Flight Yoke System bietet realistische Bedienelemente, die für jede bekanntere Flugsimulationssoftware konfiguriert werden können, um Ihr Flugerlebnis noch realistischer zu gestalten.

Chronograph: Genaue Zeit und Stoppuhrfunktion, um die genaue Dauer jeder Etappe Ihres Flugplans zu erfassen. Das Display zeigt auch an, welcher Programmiermodus gewählt ist.

8-Wege Coolie Hat (Rundumblickschalter) 2-Wege Wippschalter Einzelfunktionstaste (Rückseite des linken Griffes)

2-Wege Wippschalter

Einzelfunktionsknopf

Modusschalter mit 3 Positionen

(Rückseite des rechten Griffes)

Abnehmbare Hebelgriffe erlauben, jede beliebige Kombination von Triebwerken, Klappen, Gemischverstellung oder Propellersteigung zu konfigurieren.

Sanft gleitende Leistungshebel mit Tastenfunktion in der 0-Stellung

Drei 2-Wege Wippschalter

PZ45_Pro Flight yoke_QSG2.qxd 05/09/2007 09:55 Page 16

7. Wenn das Saitek Controller Fenster erscheint, probieren Sie bitte alle Knöpfe und Achsen aus, um zu sehen, ob Ihr Pad ordnungsgemäß funktioniert. Nach dem Test klicken Sie bitte auf OK.

8. Im Fenster Software Setup wählen Sie bitte SST Programmier-Software NICHT installieren und klicken Sie auf Weiter. Sie können die SST Programmier-Software zu einem späteren Zeitpunkt nachträglich installieren. Führen Sie hierzu die Schritte wie im folgenden Abschnitt B) beschrieben aus.

9. Im Fenster Registrieren wählen Sie bitte "Markieren Sie dieses Feld, um sich zu registrieren" und folgen Sie den Bildschirmanweisungen. Wenn Sie sich später registrieren möchten, dann markieren Sie dieses Feld nicht.

10.Um die Installation zu beenden, klicken Sie auf Fertig stellen. Ihr Saitek Controller ist nun spielbereit!

B) Komplette Installation (Treiber und Programmier-Software)

1. Führen Sie die oberen Schritte 1-7 aus bis das Fenster zur Einrichtung der Programmiersoftware erscheint. Wählen Sie hier die Option für fortgeschrittene Spieler und klicken Sie Weiter.

2. Im Fenster Treiber klicken Sie auf Update und folgen den Anweisungen. Jetzt werden Sie gefragt, ob Sie Funktionen wie Saitek Magic Mouse oder Saitek Magic Keyboard installieren wollen (dies sind XP-Namen für einige Funktionen Ihres Controllers). Bestätigen Sie mit Weiter bis Sie mit Fertigstellen die Installation abschliessen. Sie erhalten die Meldung, dass die Installation erfolgreich abgeschlossen wurde.

3. Im Fenster Registrieren wählen Sie bitte "Markieren Sie dieses Feld, um sich zu registrieren" und folgen sie den Bildschirmanweisungen. Wenn Sie sich später registrieren möchten, dann markieren Sie dieses Feld nicht.

4. Nach Abschluss der Installation können Sie sofort den Profileditor starten - heisst die Programmierung beginnen. Entscheiden Sie sich dafür, nicht sofort zu programmieren, klicken Sie auf Fertigstellen, um dies zu übergehen. Ihr Saitek Controller ist spielbereit.

Ihrem Tisch. Achten Sie bitte darauf, dass sich die Wippschalter unabhängig von der gewählten Montageart unten befinden müssen, wenn Sie auf das Gerät schauen. Ziehen Sie den Schraubmechanismus der Klemme an, bis er fest an Ihrem Tisch sitzt. Sie können den Throttle Quadrant auch links oder rechts vom Flight Yoke positionieren.

Jetzt verbinden Sie den Throttle Quadrant über den PS/2-Stecker mit der Rückseite des Flight Yoke.

Verwenden Sie den integrierten USB-Hub an der Seite des Pro Flight Yoke, um andere Geräte aus der Pro Flight Produktpalette von Saitek anzuschließen, wie beispielsweise zusätzliche Pro Flight Throttle Quadranten, Pro Flight Rudder Pedals oder andere Peripheriegeräte.

Installation unter Windows® XP, XP64 und Vista

A) Basisinstallation (nur Treiber)

1. Schalten Sie Ihren PC ein, und schließen Sie alle laufenden Programme. Legen Sie die Saitek Smart Technology CD in Ihr CD-ROM-Laufwerk.

2. Im Begrüßungsbildschirm klicken Sie bitte auf Software installieren, um fortzufahren. Wenn die CD nicht automatisch startet, wählen Sie bitte Start in der Windows Menüleiste, dann Ausführen und hier geben Sie D:\Setup.exe (ohne Anführungszeichen) ein und klicken Sie OK. Falls D:\ nicht der Laufwerksbuchstabe Ihres CD Laufwerks ist ändern Sie diesen entsprechend.

3. Im Willkommen-Fenster, klicken Sie auf Weiter, um mit der Installation zu beginnen.

4. Haben Sie den Haftungsausschluss gelesen, akzeptieren Sie diesen und klicken Weiter.

5. In der Treiberinstallationsanzeige verbinden Sie, sofern Sie das noch nicht gemacht haben, das USB-Kabel mit einem der USB-Ports des Computers und klicken Sie auf Weiter.

6. Klicken Sie in den folgenden Fenstern auf Weiter, um die Installation fortzusetzen. Nachdem Sie im Fenster Treiber-Installation auf Weiter klicken, können Sie Ihren Controller testen.

PZ45_Pro Flight yoke_QSG2.qxd 05/09/2007 09:55 Page 18

Die Knöpfe, Steuerungen und Achsen des Saitek Pro Flight Yoke Systems entsprechen den üblichen in Microsoft FS 9 und FS X benutzten Funktionen, wie in den untenstehenden Tabellen beschrieben. Wie bei jeder Software müssen Sie, wenn Sie die Funktion eines Knopfes oder eines Bedienelements ändern wollen, die Einstellung in der Software ändern.

Steuerungen des Flight Yoke und entsprechende Funktionen im Microsoft Flugsimulator

Funktion Voreingestellte Funktion in

FS 9 und FS X

Yoke-Achse X-Achse Querruder

Y-Achse Höhenruder

Hauptknöpfe Taste 1 Bremsen (anziehen/lösen)

T1 (Taste 3) Höhenruder abwärts trimmen T2 (Taste 4) Höhenruder aufwärts trimmen T3 (Taste 5) Klappen schrittweise einziehen T4 (Taste 6) Klappen schrittweise ausfahren T5 (Taste 7) Kniebrett ein-/ausblenden T6 (Taste 8) Fahrwerk auf/ab Taste 2 Ansichten (zyklisch) Coolie Hat Rundumblick

Weitere Bedienelemente Modusschalter Schaltet bei Verwendung der

Programmier-Software Saitek Smart Technology (SST) die Modi um

Chronograph Function Umschalten Uhr/Stoppuhr

Start/Stop Start/Stopp Stoppuhr Reset Rücksetzen Stoppuhr

Wichtige Informationen Anmerkungen zur Treiber-Aktualisierung

Falls notwendig werden neuere Versionen der Treiber und der Programmier-Software für dieses Produkt veröffentlicht. Sie erhalten jeweils die aktuellste Software auf der Saitek Website unter der Rubrik Downloads unter dem Menüpunkt Treiber + Software.

Konfiguration Ihres Saitek Pro Flight Yoke und Throttle Quadranten für MS Flight Simulator 2004 (FS 9) und MS Flight Simulator X (FS X)

Funktionsübersicht

Taste 1

Coolie Hat

T1 = Taste 3 T2 = Taste 4

Chronograph

Taste 2

Modusschalter

T3 = Taste 5 T4 = Taste 6

T5 = Taste 7 T6 = Taste 8

Umschalten Uhr/Stoppuhr

Start/Stopp Stoppuhr

Rücksetzen Stoppuhr

PZ45_Pro Flight yoke_QSG2.qxd 05/09/2007 09:56 Page 20

Bedienelemente des Quadranten und entsprechende Funktionen im Microsoft Flugsimulator

Funktion Voreingestellte Funktion in FS 9

und FS X

Quadranten-Achse Z-Achse Triebwerk

Rx-Achse Lande-, Wölbklappen Ry-Achse Brems-, Störklappen

Achsentasten (0-Stellung) Z-Knopf Im Spiel zuweisbar

Rx-Knopf Im Spiel zuweisbar Ry-Knopf Im Spiel zuweisbar

2-Wege Wippschalter T1 (Knopf 15) Im Spiel zuweisbar

T2 (Knopf 16) Im Spiel zuweisbar T3 (Knopf 17) Im Spiel zuweisbar T4 (Knopf 18) Im Spiel zuweisbar T5 (Knopf 19) Im Spiel zuweisbar T6 (Knopf 20) Im Spiel zuweisbar

Wie man den Flugsimulatorfunktionen die Bedienelemente des Pro Flight Yoke zuweist

Wenn Sie die Bedienelemente verändern oder die zusätzlichen Knöpfe einstellen möchten, die noch nicht automatisch vom Flugsimulator zugewiesen worden sind, müssen Sie den Bildschirm Zuweisungen (Flugsimulator 2004) oder Steuerungen (Flugsimulator X) innerhalb des Spiels verwenden. Sie erreichen ihn über das Menü Einstellungen innerhalb des Spiels.

Beim Zugriff auf den Bildschirm Zuweisungen/Steuerungen im Flugsimulator achten Sie darauf, dass in der Option Joysticktyp der Saitek Pro Flight Yoke ausgewählt ist. Wenn Sie Tasten an Ihrem Steuergerät neu zuweisen möchten, klicken Sie zuerst oben im Fenster auf den Reiter Knöpfe/Tasten.

Wenn Sie Achsen an Ihrem Steuergerät neu zuweisen möchten (den eigentlichen Steuerknüppel oder die Hebel am Throttle Quadranten), wählen Sie oben im Fenster Joystick-Achsen (Flugsimulator 2004) oder Steuerachsen (Flugsimulator X).

2322

Funktionsübersicht

Rx Achse

Z Achse

Rx Knopf

Z Knopf

T1 = Knopf 15 T2 = Knopf 16

T3 = Knopf 17 T4 = Knopf 18

T5 = Knopf 19

Ry Knopf

Ry Achse

T6 = Knopf 20

PZ45_Pro Flight yoke_QSG2.qxd 05/09/2007 09:56 Page 22

+ 25 hidden pages