ISTRUZIONI PER L’USO
sp
r
esso
tec
Sales & Service
courtesy of
Leggere attentamente queste istruzioni d’uso prima di
utilizzare la macchina
OPERATING INSTRUCTIONS
Read these operating instructions carefully before
using the machine
ITALIANOENGLISHDEUTSCHFRANÇAISESPAÑOLPORTUGUÊSNEDERLAND
Bedienungsanleitung ist vor dem ersten Gebrauch der
BEDIENUNGSANLEITUNG
Maschine aufmerksam zu lesen
MODE D’EMPLOI
Lire attentivement ce mode d’emploi avant d’utiliser
la machine
INSTRUCCIONES DE USO
Diese Leer atentamente estas instrucciones de uso
antes de utilizar la máquina
INSTRUÇÕES PARA USO
Ler atentamente estas instruções de uso antes de
utilizar a máquina
GEBRUIKSAANWIJZING
Lees deze INSTRUCTIES aandachtig door, alvorens
het apparaat te gebruiken
TYPE SUP021YADR
FOR HOUSEHOLD USE ONLY
24
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be
followed to reduce the risk of fire, electric shock, and/or injury to persons, including
the following:
1 Read all instructions and information in this instruction book and any other
literature included in this carton referring to this product before operating or using
this appliance.
2 Do not touch hot surfaces. Use handles or knobs.
3 To protect against fire, electric shock and personal injury do not immerse cord,
plugs or appliance in water or other liquid.
4 Close supervision is necessary when any appliance is used by or near children.
5 Unplug from outlet when not in use and before cleaning. Allow to cool before
putting on or taking off parts, and before cleaning the appliance.
6 Do not operate any appliance with a damaged cord or plug or after the appliance
malfunctions or has been damaged in any way. Return appliance to the nearest
authorized service centre for examination, repair or adjustment.
7 The use of accessory attachments not recommended by the appliance manufacturer
may result in fire, electric shock or personal injury.
8 Do not use outdoors.
9 Do not let cord hang over edge of table or counter, or touch hot surfaces.
10 Do not place on or near a hot gas or electric burner, or in a heated oven.
11 Always turn appliance “OFF”, then plug cord into the wall outlet. To disconnect,
turn switch to “OFF”, then remove plug from wall outlet.
12 Do not use appliance for other then intended household use.
13 Use extreme caution when using hot steam.
SAVE THESE INSTRUCTIONS
CAUTION
This appliance is for household use. Any servicing, other than cleaning and user
maintenance, should be performed by an authorized service centre. Do not immerse
base in water. To reduce the risk of fire or electric shock, do not disassemble the base.
There are no user serviceable parts inside. Repair should be done by authorized service
personnel only.
1 Check voltage to be sure that the voltage indicated on the nameplate agrees with
your voltage.
2 Never use warm or hot water to fill the water tank. Use cold water only.
3 Keep your hands and the cord away from hot parts of the appliance during
operation.
4 Never clean with scouring powders or hard implements. Simply use a soft cloth
dampened with water.
5 To avoid your coffee maker scaling up, use purified or bottled water.
INSTRUCTIONS FOR THE POWER SUPPLY CORD
A A short power-supply cord is provided to reduce risks of getting tangled up or
tripping over a longer cord.
B Longer extension cords are available and may be used if care is exercised in their use.
C If a long extension cord is used:
1 the marked electrical rating of the extension cord should be at least as great as
the electrical rating of the appliance.
2 if the appliance is of the grounded type, the extension cord should be a
grounding type
3 the cable does not hang from the table to avoid the risk of getting caught up in it.
25
GENERAL INFORMATION
This coffee machine is ideal for preparing espresso coffee either with coffee beans
or preground coffee and also features a device for dispensing steam and hot water.
This elegantly styled machine is designed for household use only. It is not suitable
for continuous professional-type use.
Warning. The manufacturer shall accept no liability for damage or injury
caused by:
• improper use or use for other than the intended purposes;
• repairs carried out by anyone other than an authorised service centre;
• tampering with the power cord;
• tampering with any machine component;
• use of spare parts and accessories other than those supplied by the
manufacturer.
The warranty will be invalidated in such cases.
TO FACILITATE INTERPRETATION
A warning triangle draws attention to the instructions that are important for user safety. Please carefully abide by these instructions to
avoid serious injury!
HOW TO USE THESE OPERATING INSTRUCTIONS
Keep these operating instructions in a safe place and make them available to
anyone else who should use the coffee machine. For further information or an
explanation of problems not completely or sufciently addressed in these instructions, contact an authorised service centre.
TECHNICAL SPECIFICATIONS
• Voltage rating See rating plate on appliance
• Power rating See rating plate on appliance
• Casing material Metal
• Size (w x h x d) (mm) 285 x 375 x 400
• Weight (Kg) 11
• Cord length (mm) 1200
• Control panel Front (Digital)
• Water tank (lit.) 2 - Extractible
• Power supply See rating plate on appliance
• Pump pressure (bars) 15
• Boiler 2 - Stainless steel
• Coffee container capacity (g.) 300 of coffee beans
• Rapid Steam Steam ready in a few seconds
• Grinders Ceramic
• Quantity of ground coffee 6 - 10 g
• Dreg drawer capacity 13
• Safety devices Boiler pressure safety valve
safety thermostat
Subject to engineering and manufacturing changes as warranted by technological
developments.
Machine in conformity with European Directive 89/336/EEC (Italian Legislative
Decree 476 of 04/12/92) concerning electromagnetic compatibility.
ENGLISH
26
SAFETY RULES
IN THE EVENT OF AN EMERGENCY
Immediately unplug the appliance.
THE APPLIANCE MAY ONLY BE USED
- In a closed place.
- To prepare coffee, dispense hot water, froth milk or heat beverages using
steam.
- For household use.
- By adults in full possession of their physical and mental capacities.
NEVER USE THE APPLIANCE
for purposes other than those indicated above to avoid hazards. Never place
any substances in the containers other than those specied in the instruction
manual. When you ll a container, make sure all nearby containers are closed.
Fill the water tank only with fresh drinking water: hot water and/or other liquids
may damage the machine. Do not use carbonated water. The coffee grinder may
be adjusted only while it is running. Do not introduce your ngers or any material
other than coffee beans into the coffee grinder. Before attempting to access the
inside of the coffee grinder, switch OFF the machine and remove the plug from
the electric socket. Do not put coffee beans or instant coffee into the ground coffee
container.
MAINS CONNECTION
Connect the coffee machine to a suitable electric socket. The voltage must match
the voltage specied on the appliance rating plate.
INSTALLATION
- Choose a perfectly level supporting surface. Do not place on a hot surface!
- Maintain a distance of 10 cm from walls and electric or gas burners.
- Do not keep at temperatures below 0 °C; the appliance may be damaged by
freezing.
- The electric socket must be accessible at all times.
- The power cord must not be damaged, secured with clamps, placed on very hot
surfaces etc.
- Do not let the power cord hang loosely (Warning: danger of tripping or of
causing the appliance to fall).
- Do not use the power cord to carry or pull the coffee machine.
HAZARDS
- The appliance must not be used by children or by individuals unacquainted with
the operating instructions.
- The appliance is dangerous for children. If left unattended it must be
switched off.
- Do not leave the materials used to pack the appliance within children’s reach.
- Do not direct a jet of hot steam and/or hot water toward yourself or others:
danger of scalding.
- Do not introduce any objects through the openings in the appliance (Electrical
hazard!).
- Do not touch the plug when your hands or feet are wet. Do not unplug the
appliance by yanking at the power cord.
- Warning: contact with hot water, steam or and hot water/steam nozzle may
cause burns.
FAULTS
- Do not use the appliance if it malfunctions or you suspect damage, e.g.
after a fall.
- Repairs must be performed by an authorised service centre.
- Do not use an appliance with a defective power cord. The cord may be replaced
exclusively by a service centre (Electrical hazard!).
- Switch off the appliance before opening the service door. Danger of burns!
CLEANING / DESCALING
- Before cleaning the appliance, unplug it and allow it to cool down.
- Avoid exposing the appliance to splashes of water. Do not immerge it in water.
- Do not dry machine components in a conventional or microwave oven.
SPARE PARTS
To guarantee safety, you should use only original spare parts and accessories.
DISPOSAL
- The packing materials can be recycled.
- Appliance: unplug the appliance and cut the power cord.
- Deliver the appliance and power cord to a service centre or public waste
disposal facility.
COMPONENT DESCRIPTION
27
Coffee bean container
Cup heater plate
Preground coffee
dispenser lid
Control panel
Service door
SBS
Height and depth
adjustable brew unit
Drip tray + grill
Tray full indicator
Dregs drawer
Brew group
Swivel base
Coffee bean container lid
Water tank lid
LCD Display
Water tank
Steam knob
ON/OFF switch
Hot water/
steam tube
Grind adjustment knob
Coffe container opening button
Cleaning
brush
Water hardness
test
Cartridge lter
applicator
TOUCH-SCREEN keys.
Different commands are associated with
these keys depending on what appears
on the LCD display. A light nger pressure will make the selected command
active; the command is then con rmed
by a sound signal.
Brew group key
Preground
coffee measure
“Aqua Prima”
cartridge lter
ENGLISH
28
INSTALLATION / VENTILATE
The messages displayed by the machine during operation are shown
on pg.43.
Fill the coffee bean container
with coffee beans.
VENTILATE
A message is displayed
indicating that the machine
circuit needs loading.
The “Aqua Prima” lter can
be installed (see pg.33).
Place a container beneath
the steam tube.
Turn the knob counterclockwise to start loading the
circuit.
Important warning for using the “Aqua Prima Filter” can be found at
page 44.
Fill the tank with fresh drinking water.
SELECT PRODUCT
READY FOR USE
See rating plate
Insert the plug into a suitable electric socket.
HOT WATER
VENTILATE
Wait until a steady stream
of water ows out from the
nozzle.
Note: You must load the circuit before starting
up the machine for the first time, if it has been
inoperative for a lengthy period or if the water
tank has been completely emptied. Moreover,
the circuit must be loaded every time the
message “VENTILATE” is displayed.
Move the ON/OFF switch
to “I” to turn on the
machine.
HOT WATER
A message is displayed
indicating that the machine
circuit has been loaded.
Turn the knob clockwise
to terminate the circuitloading process.
Remove the container. The machine is ready for
use.
ADJUSTMENT
COFFEE GRINDER
The neness of the grind may be
adjusted using the knob.
Coffee ows out more
slowly. Press and turn.
Coffee ows out more
quickly. Press and turn.
ADJUSTMENTS
Adjustment may be made only while the coffee grinder is
operating.
Use coffee bean blends for espresso coffee makers. If you do not obtain
the desired result, try using different coffee blends. Store coffee in a cool
place, in a hermetically sealed container.
You will note a change after dispensing 1 - 2 coffees.
If you set the grinder on too ne a grind (knob turned all the way
anticlockwise) and the SBS control on “strong” (toward the right), coffee
may ow out in a slow trickle or not at all.
29
ENGLISH
COFFEE DOSE ADJUSTMENT - You must adjust the dose before dispensing coffee.
This adjustment will have an immediate effect on the coffee brewed.
SELECT PRODUCT
READY FOR USE
ADJUSTMENT
COFFEE DOSE
You can adjust the quantity
SELECT PRODUCT
READY FOR USE
Stronger coffee.
SELECT PRODUCT
READY FOR USE
Weaker coffee.
of coffee to be ground.
To adjust the strength and consistency of brewed coffee. The adjustment can also be made while
brewing the coffe. This adjustment will have an immediate effect on the coffee brewed.
SBS
Espresso coffee
Strong black coffeeCafé crème
BIG CUPS
To place the brew unit again in its position, pull it until it ts in.
BIG CUPS
To use big cups, press the button and push the brew
unit until the end.
COFFEE IN CUPS
To adjust the quantity of coffee dispensed to the size of your cups.
Place a cup beneath
Or
1 SMALL COFFEE
PROGRAM. QUANTITY
COFFEE IN CUPS
lled to the desired level, release the button; the machine is now
programmed to dispense the quantity of coffee you have chosen.
the brew unit, press the
button corresponding
to the type of coffee
desired and keep it
pressed while coffee
is being dispensed.
When the cup has
30
DISPENSING COFFEE / HOT WATER
Warning! Hot water and steam may cause burns! Direct the steam tube toward the drip tray.
Before dispensing hot water, check on the display that the function has been selected.
SELECT PRODUCT
READY FOR USE
COFFEE BEANS
Make sure that the machine is ready.
PREGROUND COFFEE
Position a warm coffee cup
beneath the brew unit.
HOT WATER
Position a warm coffee
cup or cups beneath the
brew unit.
SELECT PRODUCT
PREGROUND COFFEE
Press the key one or
more times to select the
function.
SELECT PRODUCT
READY FOR USE
Or
1 SMALL COFFEE
Press the button of the
type of coffee desired.
Once for 1 coffee
Introduce ground coffee
using the coffee measure.
MAX 1 MEASURE
Close the cover.
HOT WATER
Or
2 SMALL COFFEES
Twice for 2 coffees. When the machine stops
making the coffee, remove
the cup or cups.
Or
1 SMALL COFFEE
PREGROUND COFFEE
Press the button of the
type of coffee desired.
When the machine stops
making the coffee, remove
the cup.
SELECT PRODUCT
READY FOR USE
Place a container beneath
the steam tube.
Press the button to
dispense water.
Turn the knob counterclockwise to start dispensing. Close the knob when
nished.
Remove the container. Press the button to restore
the machine to normal
operation.
Warning! Hot water and steam may cause burns! Direct the steam tube toward the drip tray.
Before dispensing hot water, check on the display that the function has been selected.
SELECT PRODUCT
READY FOR USE
STEAM / CAPPUCCINO
31
CAPPUCCINO
Fill a cup to 1/3 with cold
milk.
STEAM
Open the knob to release
steam. The machine will
signal the function
STEAM
discharge any residual
water. Close the knob.
Check that the steam
function has been selected.
Move the cup in a circular
fashion to heat the milk
evenly.
Place the cup beneath the
steam tube.
Open the knob.
Place a container beneath
the steam tube. Open the
knob to discharge any
residual water.
After frothing the milk,
close the knob.
STEAM
When only steam comes
out, close the knob.
Remove the container.
Remove the cup and
position it beneath the
brew unit
SELECT PRODUCT
READY FOR USE
Close the knob.Heat by moving in circles.
ENGLISH
Position the cup containing
milk beneath the steam
tube.
Dispense coffee into the
cup to prepare a delicious
cappuccino.
Remove the container.Open the knob to
32
DESCALING
Warning! Never use vinegar as a descaling agent. You can use any
commercially available non-toxic, non-harmful descaling product for coffee
machines. We recommend using a Saeco descaling agent.
DECALCIFY
READY FOR USE
The machine signals when
it needs descaling.
Press the MENU button
to access the descaling
DESCALING
OPEN KNOB
Remove the cartridge
lter.
function.
See “Programming”.
DESCALING FINISHED
CLOSE KNOB
RINSE MACHINE
FILL WATER TANK
When the descaling cycle is
completed, close the knob.
MACHINE IS DESCALING
OPEN KNOB
DESCAL. INTERRUPTED
EMPTY WATER TANK
Rinse out the tank and ll it
with fresh drinking water.
INTERRUPTION
Descaling is necessary every 3-4 months, when there is a reduction in the water
capacity. The machine must be on; it automatically controls the distribution of the
descaling solution.
MACHINE IS DESCALING
Fill the water tank with the
descaling solution.
Place a large receptacle
beneath the steam tube.
Turn the knob to open the
valve. The machine will
start descaling.
RINSING FINISHED
CLOSE KNOB
When the rinse cycle is
completed, close the knob
and load the circuit
RINSE MACHINE
PRESS KEY
Press the button to con rm
the rinse cycle.
MACHINE IS RINSING
Open the knob.
The machine will start
rinsing.
If the descaling cycle is
interrupted by switching off
the machine, it will automatically resume when the machine is switched
RINSE MACHINE
PRESS KEY
back on.
When descaling is over, fit the
cartridge filter back in place.
The descaling cycle can
be cut short by closing
the knob.
Press the button. Rinse out the tank and ll it
with fresh drinking water.
Press the button to con rm
the rinse cycle and proceed
normally.
“AQUA PRIMA” CARTRIDGE FILTER
33
The filter must be replaced when signalled by the machine.
See “Programming”.
INSTALLATION
Remove the lter from the
packing container.
Adjust the dater to the
current month.
Press until the end limit. Turn the applicator coun-
Insert the applicator and
turn it clockwise to secure
it to the lter.
ter-clockwise and remove
it from the tank.
Before descaling, remove the filter from the tank.
Check where the lter
positioning and reference
mark is.
Fill the tank with fresh
drinkable water.
Put the lter into the empty
tank.
Position a container
beneath the steam tube
and turn the machine on.
WATER FILTER
ON
OFF
RESET
The reference must be
positioned in correspondence with the groove.
SELECT PRODUCT
READY FOR USE
Press the button to
dispense water.
It is possible to use the
machine without lter,
Saeco suggests its use.
If lter is not used, the
machine must be descaled
more frequently.
ENGLISH
Open the knob and
dispense water.
Empty the water tank out at
intervals.
When the tank is empty, ll
it again with fresh drinkable
water.
See “Programming”. Enable
the lter control function and
reset the water counter.
You can now use your
coffee machine.
34
CLEANING AND MAINTENANCE
Do not dry the machine and/or its components in a microwave and/or
conventional oven.
BASIC
CLEANING
Turn the machine off.
Unplug the machine.
Use the brush to clean the
ground coffee dispenser.
Wash the water tank.
Wash the lter inside it.
Remove the brew unit
and wash it with water.
Do not immerge the machine in water and do not place any of its
components in a dishwasher.
Remove the drip tray, empty it out and wash it.
The machine, its components
and the brew unit must be
cleaned at least once a week.
Remove the dregs drawer,
empty it out and wash it.
Unscrew and clean the
“pannarello” attachment.
BREW
GROUP
Remove the grill. Open
the front door. Remove the
drawers.
Press the PUSH button to
release the brew group.
Unscrew the upper lter
and wash it.
Fit the lter back in place
when clean.
Wash the unit, dry it and
t it back in place. Do not
press the “PUSH” button.
Set all machine components
back in position.
Close the door.
The user can change some machine operating parameters to suit his/her personal needs.
SETTINGS
PROGRAMMING MACHINE FUNCTIONS
35
SELECT PRODUCT
READY FOR USE
START
ENERGY SAVING SETTINGS
PROGRAMMING
Press the “MENU”
button to access the
programming mode.
When the appliance is used infrequently, it can be
switched to the STANDBY mode.
With this function you can cut energy costs.
SAVING
ENERGY
This function allows you to turn on the cup heater
present in the machine cover.
With the highlighted
buttons you can view
the main menus.
CUP WARMER
The highlighted menu
item can be selected
by pressing the “OK”
button.
ENERGY SAVING
When the function appears, select it using the
“OK” button.
SETTINGS
SETTINGS
CUP WARMER
RINSING
LANGUAGE
The secondary menus
can be viewed/edited
with the highlighted
buttons.
Machine in energy saving mode.
CUP WARMER
RINSING
LANGUAGE
SETTINGS
CUP WARMER
RINSING
LANGUAGE
Use the “OK” button
to select a menu or
con rm a change.
Press the “ON” button
to restore the machine
to normal operation.
CUP WARMER
ON
OFF
SETTINGS
Press ESC to exit
without making any
changes.
SELECT PRODUCT
READY FOR USE
CUP WARMER
ON
OFF
ENGLISH
Select the MENU.
When the function appears, select it using the
“OK” button.
Choose whether you
wish to turn the cup
heater plate on or off.
Press the “OK” button
to con rm your choice.
SETTINGS
36
PROGRAMMING MACHINE FUNCTIONS
When this function is enabled, the internal
machine circuits will be rinsed immediately after
the warming-up phase to ensure that coffee is
prepared with fresh water only.
RINSING
In all new appliances this function has already
been enabled in the factory.
This function allows you to change the display
language. You can choose among Italian,
German, Portuguese, Spanish, English, French,
Dutch, Polish and Swedish. The appliance is
usually programmed on the language of the
LANGUAGE
country in which it is sold.
The hardness of tap water may vary depending on
the region. For this reason, the appliance can be
set according to the water hardness in the place
where it is to be used, expressed on a scale of 1
to 4. The appliance is factory set on a hardness
value of 3.
WATER HARDNESS
The setting should be adjusted according to the
level of water hardness in the local area.
SETTINGS
Select the MENU.
SETTINGS
Select the MENU.
Dip the strip in water for
1 second.
Check how many squares change colour.
SETTINGS
CUP WARMER
RINSING
LANGUAGE
When the function appears, select it using
the “OK” button.
SETTINGS
CUP WARMER
RINSING
LANGUAGE
When the function appears, select it using
the “OK” button.
RINSING
LANGUAGE
WATER HARDNESS
When the function appears, select it using the
“OK” button.
RINSING
ON
OFF
From this menu
you can disable the
RINSING
ON
OFF
Press the “OK” button to
con rm your choice.
function.
LANGUAGE
ENGLISH
ESPANOL
PORTUGUES
Select the desired language.
WATER HARDNESS WATER HARDNESS
1 2 3 4 1 2 3 4
LANGUAGE
ENGLISH
ESPANOL
PORTUGUES
Press the “OK” button to
con rm your choice.
Select the corresponding hardness
(e.g. 2 squares = Hardness 2) and memorize the
value by pressing the “OK” button.
PROGRAMMING MACHINE FUNCTIONS
SETTINGS
SETTINGS
SETTINGS
37
This function must be activated when the “Aqua
Prima” cartridge lter is installed for the rst time.
The “RESET” command must be activated every
time a new cartridge lter is installed.
WATER FILTER
This function enables optimal management of the
“Aqua Prima” lter as it warns the user when the
lter needs replacing.
This function allows the user to adjust the display
contrast according to personal need.
CONTRAST
This function enables/disables the acoustic signal
emitted by the machine. When the function is on,
the machine will emit an acoustic signal every
SIGNAL
time a button is pressed.
ACOUSTIC
WATER FILTER
LANGUAGE
SETTINGS
Select the MENU.
WATER HARDNESS
WATER FILTER
When the function appears, select it using
the “OK” button.
WATER HARDNESS
SETTINGS
Select the MENU. From the menu it is
WATER FILTER
CONTRAST
When the function appears, select it using
the “OK” button.
WATER FILTER
SETTINGS
CONTRAST
ACOUSTIC SIGNAL
ON
OFF
RESET
From the menu it is
possible to set the
function to ON.
CONTRAST
0
possible to set the
desired contrast.
ACOUSTIC SIGNAL
ON
OFF
WATER FILTER
ON
OFF
RESET
Press the “OK” button to
con rm your choice.
CONTRAST
2
Press the “OK” button to
con rm your choice.
ACOUSTIC SIGNAL
ON
OFF
ENGLISH
Select the MENU. From the menu it is
When the function appears, select it using
the “OK” button.
possible to set the
function to ON.
Press the “OK” button to
con rm your choice.
COFFEE SETTINGS
COFFEE SETTINGS
38
PROGRAMMING MACHINE FUNCTIONS
With this function you can restore the machine
operating parameters originally set by the
manufacturer. If you restore all the factory
settings, all customized settings will be lost.
FACTORY
SETTINGS
With the pre-brewing process the coffee is slightly
moistened before actual brewing. This brings
out the full aroma of the coffee and lends it an
excellent avour. It is possible to choose either
“enabled”, or “disabled”, or “long”.
PREBREWING
Users can adjust the temperature of small coffees
according to individual preferences: the possible
temperature settings are “low” – “medium” – “high”.
COFFEE
TEMP. SMALL
SETTINGS
Select the MENU.
COFFEE SETTINGS
Select the MENU.
COFFEE SETTINGS
SETTINGS
CONTRAST
ACOUSTIC SIGNAL
FACTORY SETTINGS
When the function appears, select it using
the “OK” button.
PREBREWING
TEMP. SMALL COFFEE
TEMP. MEDIUM COFFEE
When the function appears, select it using the
“OK” button.
PREBREWING
TEMP. SMALL COFFEE
TEMP. MEDIUM COFFEE
FACTORY SETTINGS
YES
NO
Choose whether to
restore the initial
FACTORY SETTINGS
YES
NO
Press the “OK” button to
con rm your choice:
factory settings.
PREBREWING
ON
OFF
LONG
Choose whether you
wish to turn the pre-
PREBREWING
ON
OFF
LONG
Press the “OK” button
to con rm your choice.
brewing function on
or off.
TEMP. SMALL COFFEE TEMP. SMALL COFFEE
MEDIUM
LOW
Select the MENU.
When the function appears, select it using the
“OK” button.
Select the desired
temperature.
Press the “OK” button
to con rm your choice.
PROGRAMMING MACHINE FUNCTIONS
COFFEE SETTINGS
COFFEE SETTINGS
39
Users can adjust the temperature of medium
coffees according to individual preferences: the
possible temperature settings are “low” – “medium”
COFFEE
– “high”.
TEMP. MEDIUM
Users can adjust the temperature of large coffees
according to individual preferences: the possible
temperature settings are “low” – “medium” – “high”.
COFFEE
TEMP. LARGE
For setting, when the machine is switched on, the
quantity of coffee to be ground in order to brew the
desired coffee.
AROMA
See “Settings” on page 29.
PRESELECTION
COFFEE SETTINGS
Select the MENU.
COFFEE SETTINGS
Select the MENU.
COFFEE SETTINGS
Select the MENU.
COFFEE SETTINGS
PREBREWING
TEMP. SMALL COFFEE
TEMP. MEDIUM COFFEE
When the function appears, select it using the
“OK” button.
TEMP. SMALL COFFEE
TEMP. MEDIUM COFFEE
TEMP. LARGE COFFEE
When the function appears, select it using the
“OK” button.
TEMP. MEDIUM COFFEE
TEMP. LARGE COFFEE
AROMA PRESELECTION
When the function appears, select it using the
“OK” button.
TEMP. MEDIUM COFFEE TEMP. MEDIUM COFFEE
MEDIUM
Select the desired
temperature.
TEMP. LARGE COFFEE TEMP. LARGE COFFEE
MEDIUM
Select the desired
temperature.
AROMA PRESELECTION
MILD
NORMAL
STRONG
Select the desired
quantity of coffee.
LOW
Press the “OK” button
to con rm your choice.
LOW
Press the “OK” button
to con rm your choice.
AROMA PRESELECTION
MILD
NORMAL
STRONG
Press the “OK” button
to con rm your choice.
ENGLISH
40
PROGRAMMING MACHINE FUNCTIONS
The machine offers the option of displaying the
current time in certain phases of operation.
CLOCK
DISPLAY
This function is for setting the current time.
SET
CLOCK
This function enables/disables the clock. When the
function is on, the machine will switch on and off
at the times programmed via the “ON/OFF TIME”
CLOCK
function.
TIME SETTINGS
Select the MENU.
TIME SETTINGS
Select the MENU.
TIME SETTINGS
TIME SETTINGS
SHOW CLOCK TIME
CLOCK TIME
CLOCK
When the function appears, select it using
the “OK” button.
TIME SETTINGS
SHOW CLOCK TIME
CLOCK TIME
CLOCK
When the function appears, select it using
the “OK” button.
TIME SETTINGS
SHOW CLOCK TIME
CLOCK TIME
CLOCK
SHOW CLOCK TIME
YES
NO
From the menu it is
possible to set the
function to ON.
CLOCK TIME
25 25: :8 8
Set the hour using the
buttons and memorise
by pressing “OK”.
CLOCK
ON
OFF
SHOW CLOCK TIME
YES
NO
Press the “OK” button to
con rm your choice.
CLOCK TIME
Set the minutes
using the buttons and
memorise by pressing
“OK”.
CLOCK
ON
OFF
Select the MENU.
When the function appears, select it using
the “OK” button.
From the menu it is
possible to set the
function to ON.
Press the “OK” button to
con rm your choice.
This function, which may be enabled or disabled
by the user, is used to program the machine to go
on and off at a speci c time.
ON: indicates the switch on time.
OFF: indicates the switch off time.
ON/OFF TIME
Pressing the “OK” button will memorise the set
value and make the next parameter available for
adjustment.
TIME SETTINGS
Select the MENU.
PROGRAMMING MACHINE FUNCTIONS
TIME SETTINGS
CLOCK TIME
CLOCK
ON/OFF TIME
When the function appears, select it using
the “OK” button.
ON/OFF TIME
ON
08
:25
Set the hour and
minutes and memorise
by pressing “OK”.
ON/OFF TIME
ON
08: 25
OFF
09: 45
Set the hour and
minutes and memorise
by pressing “OK”.
41
ENGLISH
This is a factory-set function that automatically
switches the machine into “Standby” when 3 hours
have elapsed since a coffee was dispensed.
The function is disabled when the “CLOCK”
TIMER
function is on.
The switch-off time can be adjusted, in 15-minute
intervals, to a minimum of 15 minutes.
This function is used to rinse all the coffeedispensing parts with water.
The rinsing cycle cannot be interrupted.
CYCLE
A person must be present during this operation.
CLEANING
Warning: a large quantity of water may be discharged
from the coffee brew unit. Before starting, empty out
the drip tray and keep an additional container handy.
TIME SETTINGS
Select the MENU.
CLEANING
Select the MENU.
TIME SETTINGS
CLOCK
ON/OFF TIME
TIMER
When the function appears, select it using the
“OK” button.
CLEANING
CLEANING CYCLE
DESCALING CYCLE
When the function appears, select it using
the “OK” button.
TIMER
3:00
Use the buttons to
adjust the timer setting.
CLEANING CYCLE CLEANING CYCLE
YES
NO
Choose whether to
enable or disable the
Press the “OK” button to
con rm your choice.
Press the “OK” button
to con rm your choice.
rinsing cycle.
TIMER
1:15
YES
NO
EXTRAS
42
PROGRAMMING MACHINE FUNCTIONS
This function is used to carry out an automatic
descaling cycle. See Page 32.
A person must be present during this operation.
CYCLE
DESCALING
This function enables the user to see how many
coffees the machine has already dispensed.
TOTAL
COFFEES
CLEANING
CLEANING CYCLE
CLEANING
Select the MENU. Press the “OK” button to
DESCALING CYCLE
When the function appears, select it using the
“OK” button.
EXTRAS
Select the MENU.
TOTAL COFFEES
When the function appears, select it using
the “OK” button.
DESCALING CYCLE
YES
NO
Choose whether to
enable or disable the
descaling cycle.
TOTAL COFFEES
The display will show
the number of coffees
the machine has
DESCALING CYCLE
YES
NO
con rm your choice.
TOTAL COFFEE
OROLOGIO
ATTIVATA
Press “ESC” to exit the
menu.
dispensed.
DISPLAY MESSAGES
43
CLOSE DOOR
Close the front door.
DREGDRAWER MISSING
Fit the drip tray and dregs drawer properly in place.
DREGDRAWER FULL
Open the door, remove the dregs drawer and empty the
used coffee grinds into a suitable container.
Important note: the dregs drawer may be emptied
only when the machine is on. The drawer must be
removed for at least 5 seconds. If you empty the
drawer with the machine off, you will not be able
to dispense coffee the next time you switch the
machine on.
BREWUNIT MISSING
COFFEE BEANS EMPTY
READY FOR USE
VENTILATE
Load the machine circuit.
ENGLISH
FILL WATERTANK
Fill the water tank with fresh drinking water.
Fill the coffee bean container and start the coffee
dispensing cycle.
Fit the brew unit properly in place.
DECALCIFY
READY FOR USE
Descale the machine
44
DISPLAY MESSAGES- NOTES ON THE AQUA PRIMA CARTRIDGE FILTER
Replace the “Aqua Prima” lter as soon as possible;
Press “ON”
REPLACE WATER FILTER
READY FOR USE
should not a new lter be available, remove the existing
one, and deactivate the “Water Filter” function (See Programming).
BREWUNIT BLOCKED
GRINDER BLOCKED
RINSING
WARMING UP. . .
Contact an authorised service centre.
Contact an authorised service centre.
The machine is in the heating phase; wait until the machine has nished this operation.
ADDITIONAL INFORMATION FOR CORRECTLY USING THE “AQUA PRIMA”
FILTER.
Please follow these simple instructions to correctly use the “Aqua prima” lter:
1. Keep the “Aqua prima” lter cool and away from sunlight; the room temperature should be between +5°C and +40°C;
2. Do not use the lter in temperatures over 60°C.
3. If the coffee machine is not used for 3 days, we recommend washing the
“Aqua prima” lter;
4 If the coffee machine is not used for more than 20 days, it is advisable to
replace the lter.
5. To store an already opened lter, seal it in a nylon bag and keep in the fridge;
do not store it in the freezer to avoid damaging the lter properties.
6. Before using the lter, leave it to soak in the water tank for 30 minutes.
7. Once it is taken out of its pack, do not keep the lter in the open air.
8. The lter must be replaced 90 days after opening the packing or after treating
60 litres of drinking water.
PROBLEMS - CAUSES - REMEDIES
45
PROBLEMS CAUSES REMEDIES
The machine does not
turn on.
The coffee is not hot
enough.
Only water is
dispensed when you
select “preground
coffee”.
No hot water or steam
is dispensed.
The machine takes a
long time to warm up.
The machine is not
connected to the power
supply.
The cups are cold. Warm up the cups.
A low temperature has
been set.
No preground coffee has
been introduced.
The tube nozzle is
clogged.
Excessive scale has
built up.
Move the main switch to ON.
Check the plug and the
connection
Set the machine on a higher
temperature.
Dispense again after
introducing preground coffee.
Clean the nozzle opening
with a needle.
During this ope-
ration, the knob must
be closed and the machine
must be off.
Descale the machine.
PROBLEMS CAUSES REMEDIES
Coffee ows out in
slow trickle or not
at all.
Excessively ne grind
and SBS control turned to
the right.
Adjust to a coarser grind (turn
the knob clockwise).
Turn the SBS control toward
the left.
ENGLISH
The brew unit cannot
be removed.
The unit has stopped in
the wrong position.
Close the door and switch on
the machine; the brew unit
will move back into position.
Saeco International Group S.p.A. - Via Panigali, 39
40041 Gaggio Montano - Bologna - Italy
Tel. +39 0534.771.111 - Fax. +39 0534.31025 - http://www.saeco.com
Cod. 1.6.589.70.00 Rev.01 del 15-04-04
Loading...