Rotel RSP-1576 Owners Manual [ru]

RSP-1576

STANDBYSTANDBY

Owner’s Manual
Manuel de l’utilisateur

5V 2.1A

2CH SUR + DISPLAYBYPASS

HDMI

MUTE

VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7

USB PC-USB XLR TUNER CD PHONO BT

RSP-1576

Surround Sound Processor
Processeur Audio Surround
Surround-Prozessor
Procesador de Sonido Envolvente
Surround sound-processor
Processore Surround
Surroundprocessor

Процессор окружающего звука

Bedienungsanleitung
Manual de Instrucciones
Gebruikershandleiding
Manuale di istruzioni
Bruksanvisning

Инструкция пользователя

2

Contents

RSP-1576 Surround Sound Processor

Important Safety Instructions ..........................................4

Figure 1: Control and Connections 5
Figure 2: Remote Control 6
Figure 3: Amplier And Subwoofer 7
Figure 4: Digital Audio and PC-USB Connections 8
Figure 5: Blu-Ray and Video Player Connections 8
Figure 6: Front USB Connections 9
Figure 7: CD Player Connections 9
Figure 8: Tuner Connections 10
Figure 9: Front HDMI Connections 10
Figure 10: Rear HDMI Connections 11
On-Screen Menus 12

About Rotel ......................................................13

Getting Started ...................................................13

Video Features 13
Audio Features 13
Surround Features 13
Other Features 13
Unpacking 13
Placement 13

Overview of Connections ............................................14

HDMI Inputs and Outputs ............................................14

Rear HDMI IN 1–6 Video Inputs r 14
Front HDMI IN 6 14
HDMI Monitor Outputs e 14

Audio Inputs and Outputs ............................................14

PHONO Input f 14
TUNER Input f 14
CD Input f 14
AUX Input f 15
BALANCED Input d 15
MULTI Input g 15
PREAMP Output h 15
DIGITAL Inputs w 15
PC-USB Input t 15
Front USB Input 5 15

Other Connections .................................................15

AC Input j 15
Master Power Switch a 15
12V TRIGGER Output i 15
REM IN Jack o 16
IR OUT Jacks p 16
Rotel Link [ 16
Rear USB Power Port \ 16
RS232 Connector y 16
NETWORK Connector u 16

Making Connections ................................................16

Connecting an External Amplier 16
Connecting a Subwoofer 16
Connecting a DVD, Blu-ray, Cable, Satellite, Game Console and HDTV Tuner 16
Connecting a Blu-ray or DVD Player 17
Connecting a Display 17
Connecting a CD Player or XLR Source 17
Connecting a Tuner 17
Connecting an iPod/iPhone 17

Front Panel Overview ..............................................17

Front Panel Display 3 17
IR Remote Sensor 2 17

Remote Control Overview ...........................................18

Overview of Buttons and Controls .....................................18

STANDBY 1 and Power ON/OFF Buttons A 18
VOLUME Knob and VOLUME UP/DOWN Buttons =D 18
DISPLAY (DISP) Button 0B 18
SETUP Button H 18
Navigation and ENTER Buttons I 18
MUTE Button -F 18
Input Buttons 4qM 18
SUR+ Buttons 9B 18
Playback Control buttons L 18
DIM Button J 18
SUB, CTR, REAR Buttons B 18
MEM Button E 18
LIGHT Button N 18
ASSISTIVE LIGHT O 18

Automatic Surround Modes ...........................................18

Manually Selecting Surround Modes ....................................19

Digital Audio 19
Analog Stereo 19

Basic Operation ...................................................19

Selecting Inputs 19

USB/iPod Operation ...............................................20

iPod/iPhone Connection 0 20
Playback Control Buttons L 20

Bluetooth. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Bluetooth Connection 20

Rear PC-USB .....................................................20

Rear PC-USB Connection 20

Setup ..........................................................20

Menu Basics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Navigation Buttons 20
Main Menu 20

Configuring Inputs .................................................20

Input Setup 21
Multi Input Setup 22

Configuring Audio ..................................................22

Audio Conguration 22

Configuring Speakers and Audio .......................................22

Speaker Conguration 22
Advanced Speaker Setup 23
Subwoofer Setup 24
Speaker Level Setup 24
Speaker and Delay/Distance Setup 25

Miscellaneous Settings ..............................................25

System Setup 25
Video Setup 26
PEQ Conguration 27

Troubleshooting ...................................................27

Specications .....................................................28

3

RSP-1576

STANDBYSTANDBY

Rotel products are designed to comply with international
directives on the Restriction of Hazardous Substances
(RoHS) in electrical and electronic equipment and
the disposal of Waste Electrical and Electronic
Equipment (WEEE). The crossed wheelie bin symbol
indicates compliance and that the products must be
appropriately recycled or processed in accordance
with these directives.

5V 2.1A

HDMI

MUTE2CH SUR + DISPLAYBYPASS

VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7

USB PC-USB XLR TUNER CD PHONO BT

Pin Assignments
Balanced Audio (3 pole XLR):

2

1

3

Pin 1: Ground / Screen
Pin 2: In phase / +ve / Hot
Pin 3: Out of phase / -ve / Cold

4

Important Safety Instructions FCC Information

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

Notice

The RS232 connection should be handled by authorized persons only.

WARNING: There are no user serviceable parts inside. Refer all servicing to qualified service personnel.
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to moisture or water. Do

not expose the unit to dripping or splashing. Do not place objects filled with liquids, such as vases, on the
unit. Do not allow foreign objects to get into the enclosure. If the unit is exposed to moisture, or a foreign
object gets into the enclosure, immediately disconnect the power cord from the wall. Take the unit to a
qualified service person for inspection and necessary repairs.

Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.

Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or

sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.

Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.

The apparatus should be used in non tropical climate.

You must allow a minimum 10 cm or 4 inches of unobstructed clearance around the unit.
WARNING: The rear panel power cord connector is the mains power disconnect device. The device must

be located in an open area that allows access to the cord connector.
The unit must be connected to a power supply only of the type and voltage specified on the rear panel.

(USA: 120 V/60Hz, EC: 230V/50Hz)
Connect the component to the power outlet only with the supplied power supply cable or an exact equivalent.

Do not modify the supplied cable. Do not use extension cords.
The mains plug is the disconnect of the unit. In order to completely disconnect the unit from the supply

mains, remove the main plug from the unit and the AC power outlet. This is the only way to completely
remove mains power from the unit.

The main plug is used as the main disconnect device and should remain ready accessible.
The batteries in remote control shall not be exposed to excessive heat such as sunshine, fire or the like.

Batteries should be recycled or disposed as per state and local guidelines.
WARNING: The master power switch is located on the rear panel. The unit must allow unobstructed

access to the main power switch.

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction, may cause harmful interference
to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:

• Reorient or relocate the receiving antenna.(TV, radio, etc.).

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for additional help.

Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following to conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
interference in a residential installation. This equipment generates and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause interference to radio or TV
communications. There is no guarantee that interference will not occur in a particular installation. If this
equipment does cause interference to radio or television reception, which can be determined by turning
the equipment off and on, try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the unit and the television tuner.

• Connect the unit to an AC power outlet on a different electrical circuit.

• Consult your authorized Rotel retailer for assistance.

RSP-1576 Surround Sound Processor

DAB

5

Figure 1: Control and Connections

Commandes et Connexions
Bedienelemente und Anschlüsse
Controles y Conexiones

1 2

RSP-1576

STANDBYSTANDBY

5V 2.1A

HDMI

2CH SUR + DISPL AYBYPASS

MUTE

Bedieningselementen en aansluitingen
Controlli e connessioni
Kontroller och anslutningar

Органы управления и соединения

3

VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7

USB PC-USB XLR TUNER CD PHONO BT

4

w

5

6 78

90

-

e i

PUSH

PUSH

=

uytr

o

p

[

]

\

q

a

I

O

s

d

f

g

h

j

6

RSP-1576 Surround Sound Processor

Figure 2: Remote Control

Télécommande
Fernbedienung
Mando a Distancia

A

B

C

E

Afstandsbediening
Telecomando
Fjärrkontroll

Пульт дистанционного управления

A

O

D

F

G

J

L

M

H
I

K

N

7

Figure 3: Amplier And Subwoofer

Amplicateurs et caissons de graves
Verstärker und Subwoofer
Amplicador y Subwoofer

FRONT LEFT
AMPLIFIER

CENTER

AMPLIFIER

Versterker en subwoofer
Collegamento di amplicatori e subwoofer
Förstärkare och subbas

Усилитель и сабвуфер

SUBWOOFER

FRONT RIGHT

AMPLIFIER

INPUT

I

O

PUSH

PUSH

REAR LEFT
AMPLIFIER

CB LEFT (1)

AMPLIFIER

REAR RIGHT

AMPLIFIER

CB RIGHT (2)

AMPLIFIER

8

RSP-1576 Surround Sound Processor

Figure 4: Digital Audio and PC-USB Connections

Connexions audio numériques et PC-USB
Digitale Audio und PC-USB verbindungen
Conexiones Digitales de Audio y PC-USB

PUSH

PUSH

CD PLAYER

OPTICAL

COAXIAL

DIGITAL AUDIO OUTPUT

Digitale audio- en PC-USB-aansluitingen
Collegamenti audio digitale e PC-USB
Digitala ljud- och PC-USB-anslutningar

Подсоединения цифрового аудио и PC-USB

I

O

Computer

Figure 5: Blu-Ray and Video Player Connections

Connexions à un lecteur Blu-Ray ou Vidéo
Anschlussdiagramm für Blu-Ray- und Video-Player
Conexiones para Reproductor de Video o Blu-Ray

PUSH

PUSH

DVD or BLUERAY PLAYER

Aansluitingen voor een Blu-Ray of Video-speler
Collegamento di lettori Blu-Ray o Video
Blu-Ray- eller Video-spelare

Подключения Blu-Ray или Видео проигрывателя

I

O

FRONT R SUBREAR R CENTRE FRONT LREAL L

MULTICHANNEL ANALOG OUTPUT

9

Figure 6: Front USB Connections

Connexions USB en face avant
Frontseitiger USB-Anschluss
Conexiones USB del Panel Frontal

RSP-1576

STANDBYSTANDBY

5V 2.1A

HDMI

USB-aansluiting op het voorpaneel
Ingresso USB frontale
USB-anslutning på fronten

Подключение USB-накопителей к фронтальному порту

VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7

MUTE2CH SUR + DISPLAYBYPASS

USB PC-USB XLR TUNER CD PHONO BT

Figure 7: CD Player Connections

Connexions à un lecteur de CD
Anschlussdiagramm für einen CD-Spieler
Conexiones para Reproductor de CD

PUSH

PUSH

Cd-speleraansluitingen
Collegamento di un lettore CD
CD-spelare

Подключения CD-плеера

I

O

CD PLAYER

RIGHT LEFT

BALANCED AUDIO OUTPUT

DIGITAL

AUDIO OUTPUT

RIGHT LEFT

ANALOG

10

RSP-1576 Surround Sound Processor

Figure 8: Tuner Connections

Connexions à un tuner
Anschlussdiagramm für einen Tune
Conexiones para Sintonizador

PUSH

Aansluitingen voor Tuner
Collegamento di un Sintonizzatore
Tuner Anslutning

Подключение Тюнера

I

O

PUSH

TUNER

DIGITAL

RIGHT LEFT

ANALOG

AUDIO OUTPUT

Figure 9: Front HDMI Connections

Connexions HDMI avant
Vorderseite HDMI-Verbindungen
Conexiones HDMI del Panel Frente

RSP-1576

STANDBYSTANDB Y

5V 2.1A

HDMI

2CH SUR + DISPLAYBYPASS

MUTE

HDMI-aansluitingen op de voorzijde
Collegamento delle prese HDMI anteriore
HDMI-anslutning på främre

Подключение к HDMI разъему на передний панели

VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7

USB PC-USB XLR TUNER CD PHONO BT

11

Figure 10: Rear HDMI Connections

Connexions HDMI arrières
Rückseitige HDMI-Verbindungen
Conexiones HDMI del Panel Posterior

Blu-ray Player or other digital source with HDMI output

HDMI-aansluitingen op de achterkant
Collegamento delle prese HDMI posteriori
HDMI-anslutning på baksidan

Подключение к HDMI разъему на задней панели

I

O

PUSH

PUSH

480p/576p/720p/1080i/1080p HDTV/ 4K UHDTV

12

RSP-1576 Surround Sound Processor

On-Screen Menus
Afchage des menus à l’écran
On-Screen-Menüs
Sistema de Menús en Pantalla

INPUT SETUP

SOURCE
NAME
VIDEO INPUT
AUDIO INPUT
TRIGGER OUTPUT
DEFAULT MODE
AUDIO DELAY
LEVEL ADJUST

BACK

INPUT SETUP

SOURCE
NAME
VIDEO INPUT

TRIGGER OUTPUT

LEVEL ADJUST

BACK

VIDEO 1
VIDEO 1
HDMI Audio

Mul Input

1 _ _

Source Dependent

0m sec
0dB

MULTI INPUT
M-INPUT
HDMI1

1 _ _

0dB

MAIN MENU

INPUT SETUP
AUDIO CONFIGURATION
SPEAKER CONFIGURATION
SPEAKER DISTANCE SETUP
SUBWOOFER SETUP
SPEAKER LEVEL SETUP
VIDEO SETUP
PEQ CONFIGURATION
SYSTEM SETUP
EXIT

SPEAKER CONFIGURATION

FRONT
CENTER
SURROUND
SUBWOOFER
CENTER BACK
OVERHEAD FRONT
OVERHEAD REAR
ADVANCED SETUP
BACK

Large
Small
Small
Yes
None
None
None

ADVANCED SPEAKER SETUP

SPEAKER
CROSSOVER
DOLBY
DTS
STEREO
BACK

Front
100Hz
Default
Default
Default

Schermmenu’s
Menù sul display (OSD)
Menyer

Экранные меню

SPEAKER DISTANCE SETUP

FRONT LEFT
CENTER
FRONT RIGHT
SURROUND RIGHT
CENTER BACK RIGHT
OVERHEAD FRONT RIGHT
OVERHEAD REAR RIGHT
OVERHEAD REAR LEFT
OVERHEAD FRONT LEFT
CENTER BACK LEFT
SURROUND LEFT
SUBWOOFER
BACK

SPEAKER LEVEL SETUP

FRONT LEFT
CENTER
FRONT RIGHT
SURROUND RIGHT
CENTER BACK RIGHT
OVERHEAD FRONT RIGHT
OVERHEAD REAR RIGHT
OVERHEAD REAR LEFT
OVERHEAD FRONT LEFT
CENTER BACK LEFT
SURROUND LEFT
SUBWOOFER
BACK

10.00 FT 3.05M

10.00 FT 3.05M

10.00 FT 3.05M

10.00 FT 3.05M

10.00 FT 3.05M

10.00 FT 3.05M

10.00 FT 3.05M

10.00 FT 3.05M

10.00 FT 3.05M

10.00 FT 3.05M

10.00 FT 3.05M

10.00 FT 3.05M

0dB
0dB
0dB
0dB
0dB
0dB
0dB
0dB
0dB
0dB
0dB
0dB

INPUT SETUP

SOURCE
NAME
VIDEO INPUT
AUDIO INPUT
TRIGGER OUTPUT
DEFAULT MODE
AUDIO DELAY
LEVEL ADJUST
FIXED VOLUME
BACK

AUDIO CONFIGURATION

CONFIGURATION

FRONT
CENTER
SUBWOOFER
SURROUND
CENTER BACK
HEIGHT 1
HEIGHT 2
BACK

PC-USB
PC-USB
HDMI 1
USB Audio 2.0
1 _ _
Source Dependent
0m sec
0dB
Variable

7.1.4

Front
Center
Subwoofer
Surround
Center Back
Overhead Front
Overhead Rear

POWER OPTION

OFF TIMER
MAX POWER ON VOLUME 45
POWER MODE
SIGNAL SENSE INPUT
BACK

20 MINS

Normal
Disable

SUBWOOFER SETUP

DOLBY
DTS
STEREO
MULTI LPCM
MULTI INPUT
BACK

0dB
0dB
0dB
0dB
0dB

PEQ CONFIGURATION

SPEAKER : Front Le

FREQUENCY : 20Hz
FREQUENCY : 40Hz Q : 1 GAIN : 0
FREQUENCY : 60Hz Q : 1 GAIN : 0
FREQUENCY : 120Hz Q : 1 GAIN : 0
FREQUENCY : 200Hz Q : 1 GAIN : 0
FREQUENCY : 500Hz Q : 1 GAIN : 0
FREQUENCY : 1200Hz Q : 1 GAIN : 0
FREQUENCY : 4000Hz Q : 1 GAIN : 0
FREQUENCY : 12000Hz Q : 1 GAIN : 0
FREQUENCY : 20000Hz
BACK

Q : 1

Q : 1

GAIN : 0

GAIN : 0

NETWORK CONFIGURATION

IP ADDRESS MODE
RENEW DHCP IP ADDRESS
VIEW NETWORK SETTINGS
TEST NETWORK CONNECTION
BACK

DHCP

VIDEO SETUP

STANDBY VIDEO SOURCE
FAST AUDIO SYNC
OSD FORMAT
BACK

SYSTEM SETUP

LANGUAGE
IR REMOTE CODESET
PEQ FUNCTION
DISPLAY
POWER OPTION
NETWORK CONFIGURATION
SOFTWARE INFORMATION
RESTORE FACTORY DEFAULT
BACK

RESTORE FACTORY DEFAULT

ERASE ALL SETTINGS!
BACK

Disable
Disable
480P

English
Codeset 1
Disable
HDMI And VFD

13

About Rotel

Our story began over 50 years ago. Over the decades, we have received
hundreds of awards for our products and satised hundreds of thousands
of people who take their entertainment seriously- like you!

Rotel was founded by a family whose passionate interest in music led them
to manufacture high-delity components of uncompromising quality. Through
the years, that passion has remained undiminished and the family goal of
providing exceptional value for audiophiles and music lovers, regardless
of their budget, is shared by all Rotel employees.

Rotel’s engineers work as a close team, listening to, and ne tuning, each
new product until it reaches their exacting musical standards. They are
free to choose components from around the world in order to make that
product the best they can. You are likely to nd capacitors from the United
Kingdom and Germany, semiconductors from Japan or the United States,
while toroidal power transformers are manufactured in Rotel’s own factory.

We all have concerns about our environment. And, as more and more
electronics are produced it is especially important for a manufacturer to do all
it can to engineer products that have a minimum impact on the environment.

At Rotel, we are proud to do our part. We have reduced the lead content
in our products by using special lead-free ROHS solder and components.
Our engineers continually strive to improve power supply efciency without
compromise to quality. When in standby mode Rotel products use minimal
power to meet global Standby Power Consumption requirements.

The Rotel factory is also doing their part to help the environment through
constant improvements to product assembly methods for a cleaner and
greener manufacturing processes.

All of us at Rotel thank you for buying this product. We are sure it will bring
you many years of enjoyment.

Getting Started

Thank you for purchasing the Rotel RSP-1576 Surround Sound Processor.
The unit is a full-featured audio/video control center for analog and digital
source components. It features digital processing for a wide range of formats
including Dolby® Surround, Dolby® ATMOS and DTS® source material.

Video Features.

• HDMI switching for digital video signals up to 4K.

• Accepts HDMI video input: 480i, 480p/576p, 720p, 1080i, 1080p,
1080p 24Hz, 4K.

• Outputs HDMI video (480i, 480p/576p, 720p, 1080i, 1080p, 1080p
24Hz, 4K) compatible with common HDMI displays and projectors.

Audio Features

• Rotel’s Balanced Design Concept combines advanced circuit board
layout, comprehensive parts evaluation, and extensive listening tests
for superior sound and reliability.

• Analog bypass mode for pure 2 channel stereo with no digital processing.

• Digital and analog inputs including Coax, Optical, RCA and Balanced
XLR.

• 7.1 Multi-Channel input from compatible source components.

Surround Features

• Automatic Dolby® and DTS surround decoding of all popular formats
up to 7.1.4 channels.

• Surround modes for playback of multi channel audio on 2 channel
and 3 channel systems.

• Audio Return Channel (ARC) allowing the audio from the TV to be
processed by the RSP-1576 via HDMI.

Manufactured under license from Dolby Laboratories. Dolby, Pro Logic,
and the double-D symbol are registered trademarks of Dolby Laboratories.

For DTS patents, see http://patents.dts.com. Manufactured under license
from DTS Licensing Limited. DTS, the Symbol, DTS in combination with the
Symbol, DTS:X, and the DTS:X logo are registered trademarks or trademarks
of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All
Rights Reserved.

Other Features

• User friendly ON-SCREEN DISPLAY (OSD) menu system with
programmable labels for all inputs.

• Multi language support in OSD setup.

• Upgradable software to accommodate future updates through the rear
Internet connection or front USB port.

• Assignable 12V trigger outputs for remote turn-on of power amplier(s)
and other components.

Unpacking

Remove the unit carefully from its packaging. Find the remote control and
other accessories. Save the box as it will protect the product if you move
or need to return it for maintenance.

Placement

Place the unit on a solid, level surface away from sunlight, heat, moisture,
or vibration. Make sure that the shelf can support the weight of the unit.

14

RSP-1576 Surround Sound Processor

Place the unit close to the other components in your system and, if possible,
on its own shelf or with the optionally included rack ears. This will make
initial connection, and subsequent system changes easier.

The unit can generate heat during normal operation. Do not block ventilation
openings. Allow a minimum of 10 cm or 4 inches of unobstructed space
around the unit. If installed in a cabinet, make sure that there is adequate
ventilation.

Do not stack other components or objects on top of the unit. Do not let any
liquid fall into the cabinet.

Overview of Connections

NOTE: Do NOT plug any system component into an AC source until
all connections have been properly made.

Source components within the system can be connected to the unit’s inputs
with either a pair of standard RCA cables or balanced XLR cables for analog
audio, or digitally, via HDMI, coax or optical.

Outputs of the RSP-1576 are sent to the power amplier(s) with standard
RCA cables from the preamp audio outputs. The video signal from the
RSP-1576 is sent to the monitor using the HDMI connections.

In addition, the processor has MULTI INPUT connections for use with a
source component that does its own surround decoding, remote IR receiver
inputs, 12V trigger outputs.

Front HDMI IN 6

The Video 7 input is located on the front panel for easier access. Use
this HDMI connection for portable sources or devices that would not be
permanently connected.

HDMI Monitor Outputs e

The two HDMI outputs of the RSP-1576 can send High Denition video
signals to two display devices in parallel. The HDMI outputs can send video
signals to a high-definition TV 2D (480p/576p, 720p, 1080i, 1080p or
4K) and 3D (up to 1080p/24Hz). Both HDMI output will support 4K UHD
HDCP 2.2 as labeled on the rear panel.

There are two HDMI outputs on the rear panel sending out the same video
signal. Only one of the two will send the On Screen Menu to your TV.

Of the two HDMI Outputs, only one HDMI output supports ARC (Audio
Return Channel) and is labeled “ARC/OSD” above the HDMI connector.
Please refer to the INPUT SETUP menu section of this manual for more
details on page 21.

Your TV may have more than one HDMI input. Not all HDMI inputs support
ARC. Please use the ARC enabled HDMI input of your TV to use the ARC
function on this product. ARC compatible inputs should be labeled with
“ARC” next to the HDMI input connector.

Additional information for HDMI video outputs:

• All HDMI attached devices must be HDCP compatible to ensure proper
display of the HDMI video signal.

NOTE: The S/PDIF digital audio interface standard specifies a 75
ohm impedance and all good digital cables adhere to this requirement.
Do NOT substitute conventional audio interconnect cables for digital
signals. Standard audio interconnects will pass these signals, but their
limited bandwidth reduce performance.

When using analog audio connections ensure the Left and Right signals are
attached to the proper RCA jacks. All RCA-type connections on this product
follow these standard color codes:

Left channel audio: white RCA jack
Right channel audio: red RCA jack

NOTE: Each source input must be properly configured using the INPUT
SETUP menu of the OSD menu system. We recommend going to this
menu after connecting each source to configure it as desired. See Input
Setup in the Setup section for more information.

HDMI Inputs and Outputs

These connections are used for connecting video signals to and from the
unit. See the Making Connections section for specific instructions for each
type of component on page 16.

Rear HDMI IN 1–6 Video Inputs r

HDMI inputs provide digital video connections for use with components that
have HDMI outputs. HDMI connections carry video signals in multiple formats
including 3D, 1080p/24Hz, and 4K. The implementation of HDMI supports
audio signals, or a separate audio connection from an HDMI component.
All HDMI inputs support 4K UHD HDCP 2.2 as labeled on the rear panel.

• Audio received over HDMI will be processed by this product and sent
out via the RCA terminal outputs.

• When using both HDMI outputs simultaneously, both HDMI outputs
will be set to the same resolution. This resolution will be the lower
resolution of any attached monitor.

Audio Inputs and Outputs

This Rotel processor provides both analog and digital audio connections.

PHONO Input f

A Left/Right pair of RCA analog audio inputs for connecting a phono player
with a moving magnet cartridge. If the turntable has a “ground” wire, connect
it to the screw terminal labeled “GND” to the left of the Digital inputs.

TUNER Input f

A Left/Right pair of RCA analog audio inputs for connecting a tuner.

CD Input f

A Left/Right pair of RCA analog audio inputs for connecting a CD player.
By default the CD source is set to CD analog RCA input, but this can be
changed to XLR, Coax 1-3 or Optical 1-3 in the input setup menu.

AUX Input f

A Left/Right pair of RCA analog audio inputs for connecting a audio
playback device with an analog audio output.

15

BALANCED Input d

A Left/Right pair of Balanced XLR audio inputs for connecting a source
component with Balanced XLR audio outputs.

MULTI Input g

A set of RCA inputs accepting up to 7.1 channels of analog signals from a
source component capable of decoding multi channel audio. These inputs
support FRONT L & R, CENTER, SUB, REAR L & R, and CENTER BACK
L[1] & R[2].

These inputs bypass all digital processing in the RSP-1576 and are routed
directly to the volume control and outputs.

PREAMP Output h

A group of fourteen RCA analog audio outputs sends the RSP-1576’s line
level output signals to external ampliers and powered subwoofers. These
output levels are variable and adjusted by the RSP-1576’s volume control.
The fourteen connectors provide output for: FRONT L & R, REAR L & R,
CENTER BACK L[1] & R[2], CENTER 1 & 2, SUBWOOFER 1 & 2, HEIGHT
1 L & R and HEIGHT 2 L & R.

DIGITAL Inputs w

The RSP-1576 accepts digital inputs from source components such as CD
players, satellite TV tuners, and DVD players. The DSP in the RSP-1576
detects the sampling rate of the incoming signal and automatically adjusts.
Sampling rates up to 192kHz are supported.

• Press SETUP on the remote control to enter MAIN MENU and use
Up/Down buttons to select the INPUT SETUP menu then press ENTER.

• Use Left/Right buttons to select “PC-USB” as INPUT SOURCE and select
“USB Audio 1.0” as AUDIO INPUT.

• Power cycle the RSP-1576 and reboot your PC after changing the USB
Audio mode to ensure both units are properly congured.

Many audio playback applications do not support 192kHz sampling rate.
Please conrm your audio player supports 192kHz audio and you have
192kHz audio les to properly playback this sample rate. Also, you may
need to congure the audio driver in your PC to output 192kHz or your
computer may “down sample” to a lower audio sample rate. For more
information please refer to your audio player or operating system information.

NOTE: Upon successful installation of the driver, you may need to select
the ROTEL audio driver from the audio/speaker setup of your computer.

Front USB Input 5

See Figure 6

This connection will accept Apple devices such as iPod, iPad and iPhone.
While connected, the iPod and iPhone displays remain active allowing
search and play functions.

NOTE: Digital inputs support both 2 Channel Stereo and Multi Channel
audio signals. When using the digital input with a Multi Channel
audio signal the processor DSP will decode the incoming audio stream
including Dolby or DTS.

There are six digital audio inputs on the rear panel, three coaxial and
three optical. These digital inputs can be assigned to any of the VIDEO
1 - 7 input sources using the INPUT SETUP menu during the setup process.
For example, you can assign the COAXIAL 1 digital input connector to the
VIDEO 1 source and the OPTICAL 2 digital input to the VIDEO 3 source. By
default, the source of the audio for inputs Video 1 - 7 is set to HDMI Audio.

By default the CD source is set to CD analog RCA input, but this can be
changed to XLR, Coax 1-3 or Optical 1-3 in the input setup menu.

PC-USB Input t

See Figure 4

Connect this input using the supplied USB cable to the USB socket of your
computer.

The RSP-1576 supports both USB Audio Class 1.0 and USB Audio Class 2.0
modes. Windows computers do not require installation of a driver for USB
Audio Class 1.0 and support playback of audio up to 96kHz sampling rates.

The Factory Default setting is USB Audio Class 2.0. To take advantage of
USB Audio Class 2.0 audio playback supporting up to 192kHz sampling
rates you will need to install the Windows driver supplied on the CD included
with the RSP-1576.

You can switch the RSP-1576 to USB Audio Class 1.0 playback mode with
the following:

Other Connections

AC Input j

Your Rotel processor is configured at the factory for the proper AC line
voltage in the country where you purchased it (USA: 120 volts/60 Hz
AC or CE: 230 volts/50 Hz AC). The AC line configuration is noted on a
decal on the back of your unit. Plug the supplied cord into the AC INPUT
receptacle on the back of the unit.

Master Power Switch a

The large rocker switch on the rear panel is a master power switch. When
it is in the OFF position, power to the unit is completely off. When it is in
the ON position, the front panel STANDBY and remote control ON/OFF
buttons can be used to activate the unit or put it into standby mode.

12V TRIGGER Output i

Many Rotel ampliers offer the option of turning them on and off using a
12 volt trigger. These three connections provide this 12 volt trigger signal
from the processor. When the unit is activated, a 12 volt DC signal is sent
from these jacks to the ampliers to automatically turn them on. When the
processor is put in STANDBY mode, the trigger signal is removed and the
ampliers automatically turn off.

To use the automatic trigger turn on feature, connect one of the RSP-1576’s
12V TRIG OUT jacks to the 12 volt trigger input of a Rotel amplier, using
only the black 3.5 mm trigger cable included with this unit or a Rotel
amplier. Do not use any other cable for trigger connection. The +12V DC
signal appears at the “tip” of the connector.

The 12V Trigger outputs are configured to turn on in various combinations
only when specific input sources are activated. See the INPUT SETUP menus
in the Setup section of this manual for details on page 21.

16

RSP-1576 Surround Sound Processor

REM IN Jack o

This 3.5 mm mini-jack receives command codes from third-party IR remote
receiver. These remote IR inputs can be used when the RSP-1576 front IR
receiver cannot be reached by a sending remote control.

Consult your authorized Rotel dealer for more information on the REM IN jack.

The IR signals from the REM IN jack can be relayed to other source components
using external IR emitters or hard-wired connections from the IR OUT jacks.
See the following section for additional information.

IR OUT Jacks p

The IR OUT 1 & 2 jacks send IR signals received at the REM IN jack to
an infrared blaster or emitter placed in front of a source component’s IR
sensor. In addition, the IR OUT can be hard-wired to other Rotel products
with a REM IN jack.

These outputs allow IR signals to be “relayed” through the RSP-1576 either
directly to the IR receiver on the front panel or via the REM IN jack on the
rear panel. This function provides easy control of other source components
when their IR inputs are not accessible such as when they are installed in
a rack system or in a cabinet.

See your authorized Rotel dealer for more information on IR emitters and
repeater systems.

Rotel Link [

Rotel Link is not used for RSP-1576.

Rear USB Power Port \

The rear USB port provides 5V for charging or powering USB devices
including streaming music players. This port does not allow playback of audio.

The port can be congured to remain powered even when the RSP-1576 is
in standby mode through the front panel setup menu (See the Power Mode
under the Power Option menu on page 26).

Making Connections

Connecting an External Amplier

See Figure 3

The RSP-1576 has preamp RCA outputs for connections to external power
ampliers to drive up to 12 speakers in congurations from 5.1 to 7.1.4.
In addition, there are two subwoofer outputs.

To connect ampliers, connect an audio cable from each output jack to the
input of the amplier channel that will power the corresponding speaker.
For example, connect the FRONT L output to the amplier channel driving
the front left speaker. There are two CENTER RCA jacks; use either jack for
a single center channel, or both if you have two center channels. In six or
seven channel systems, make one or two additional connections for Center
Back channel(s). These jacks are labeled CB L[1] and CB R[2]. Use CB L[1]
for a single center back channel. Ceiling or Overhead speakers should be
connected to the Height 1 and Height 2 jacks.

For preamp output connection information see Audio Conguration options
in the RSP-1576 Setup Menu on page 22.

After you have connected the preamp outputs, you need to configure the
RSP-1576 for the size and style of speakers in your system and calibrate the
relative volume levels of the speakers. See the Speaker Level Setup section
of this manual on page 24.

Connecting a Subwoofer

See Figure 3

To connect a powered subwoofer, connect a standard RCA audio cable
from the jacks labeled SUB 1/SUB 2 to the input on the subwoofer’s power
amp. Both SUB outputs provide the same signal. Use either connection
for a single subwoofer. Use both connections to connect two subwoofers.

The Power Mode “Quick” option allows the attached streaming source to
remain powered for use with the Signal Sense function for automatic power
on/off control of the RSP-1576.

NOTE: When configured to provide continuous power to the rear
panel USB port the RSP-1576 will consume additional power even
when in standby mode.

RS232 Connector y

The RSP-1576 can be controlled via RS232 for integration with automation
systems. The RS232 connector accepts a standard straight DB-9 Male-to­Female cable.

NETWORK Connector u

The Network socket accepts standard RJ-45, CAT-5 cables. The network
connection is not required for normal operation of this unit. This connection
is for software updates or control from an automation system only.

For additional information on the connections, cabling, software, and
operating codes for automation system control or software updates, contact
your authorized Rotel dealer.

After you have connected the subwoofer, you need to configure the unit to
use the subwoofer and calibrate the relative volume level of the subwoofer.
See the Speaker Level Setup section of this manual on page 24.

Connecting a DVD, Blu-ray, Cable, Satellite, Game Console and HDTV Tuner

See Figure 5 and 9

Source devices including Blu-ray, DVD, satellite, cable, etc. should be attached
to the RSP-1576 using HDMI. Connect an HDMI cable from the output of
the source to one of the HDMI inputs on the processor.

Digital audio connection: Depending on the setup of your system, you can also
use the audio digital connections and assign them to the HDMI video inputs.

Connect the digital output of the source to any of the DIGITAL IN OPTICAL
1–3 or DIGITAL IN COAXIAL 1–3 inputs on the processor. An HDMI cable
carries both digital video and digital audio signals; therefore, in most cases
no separate digital audio connection needs to be made.

Use the INPUT SETUP screen to assign the audio digital input to the HDMI
video input source used above.

17

Connecting a Blu-ray or DVD Player

See Figure 5

In some cases DVD, SACD, and other external multichannel processors are
connected to the processor by sending decoded analog audio signals using
RCA cables. A player with HDMI outputs can send digital signals directly
to the processor for decoding.

Analog Connections: To connect a Blu-ray or DVD player (or any device that
decodes multi-channel audio) with analog connections, use audio RCA cables
to connect the outputs of the player to the RCA jacks labeled MULTI INPUT
on the RSP-1576. Make sure that you observe proper channel consistency,
i.e. connect the right front channel to the FRONT R input, etc.

Depending on your system configuration, make six connections (FRONT L
& R, REAR L & R, CENTER, and SUBWOOFER), seven connections (adding
a CENTER BACK connection), or eight connections (adding two CENTER
BACK connections).

The MULTI inputs are analog bypass inputs, passing signals directly to the
Volume Control and preamp outputs, bypassing all of the digital processing.

HDMI digital connection: If the player has HDMI outputs, simply connect
an HDMI cable from the output of the player to one of the HDMI inputs
on the processor. This cable sends the video signal from the player along
with a digital audio signal. Using HDMI for audio and video allows the
multichannel decoding to be handled by the processor.

Although there are typically no video connections for a CD Player, the
RSP-1576 can assign another video input to the CD or XLR input. The Video
choices are HDMI 1-7 (Front), Last Video Source, or Off. HDMI 1 video
input is assigned to CD and XLR as the default setting.

Connecting a Tuner

See Figure 8

Digital audio connection: If using an HD Radio or other digital tuner, connect
the digital output of the tuner to the Optical or Coax digital inputs on the
RSP-1576. Use the INPUT SETUP menu to assign the audio input to the
TUNER source (the default is TUNER analog input jacks).

Analog audio connection:
Option 1: If using an analog tuner, connect the left and right analog outputs

from the tuner to the pair of analog input jacks labeled TUNER on the
RSP-1576. Make sure that you connect the right channel to the R input jack
and the left channel to the L input jack.

Option 2: If your Tuner has XLR output connectors, you can use the XLR inputs
on the RSP-1576 for this connection. Connect the left and right XLR outputs
from the source to the jacks labeled BALANCED INPUT (left and right).

Although there are typically no video connections for a Tuner, the
RSP-1576 can assign another video input to the Tuner input. The Video
choices are HDMI 1 - 7 (Front), Last Video Source, or Off. HDMI 1 video
input is assigned to the Tuner input as a default setting.

Connecting a Display

See Figure 10

Connect one of the HDMI outputs of the RSP-1576 to the HDMI input of
your TV or projector. The RSP-1576 has two HDMI outputs. Only one HDMI
output will display the OSD and is ARC enabled. This output is labeled on
the rear panel with ARC/OSD.

Connecting a CD Player or XLR Source

See Figure 7

Digital audio connection: Connect the digital output of the CD player to the
Optical or Coax digital inputs on the RSP-1576. Use the INPUT SETUP menu
to assign the audio input to the CD (the default is CD).

Analogue audio connections:
Option 1: Connect the left and right analog outputs from the CD player to

the AUDIO IN jacks labeled CD (left and right). This option uses the CD
player’s D/A converter. Depending on the selected DSP mode this connection
method may require the analog signal to be converted to a digital signal
for processing.

Option 2: If your CD Player (or another source) has XLR output connectors,
you can use the XLR inputs on the RSP-1576 for this connection. Connect the
left and right XLR outputs from the source to the jacks labeled BALANCED
INPUT (left and right). This option uses the CD player’s D/A converter.
Depending on the selected DSP mode this connection method may require
the analog signal to be converted to a digital signal for processing.

Connecting an iPod/iPhone

See Figure 6

Connect the iPod/iPhone to the front USB socket.

NOTE: The audio inputs CD, PHONO, XLR, MULTI, USB, PC-USB,
BLUETOOTH, and TUNER are set to HDMI 1 video input as the factory
default. Video input can be changed to HDMI 1-7 (Front), Last Video
Source, or Off.

Front Panel Overview

The following is a brief overview of the controls and features on the front
panel of the unit. Details concerning the use of these controls are provided
in subsequent sections of this manual describing various tasks.

Front Panel Display 3

The Display on the front panel shows the volume, DSP mode, source selected
and type of audio mode the unit is receiving or processing.

IR Remote Sensor 2

This sensor receives IR signals from the remote control. Do not block this sensor.

NOTE: The remainder of the buttons and controls on the front panel
are described in the Overview of Buttons and Controls section.

18

RSP-1576 Surround Sound Processor

Remote Control Overview

The RSP-1576 is supplied with an easy to use remote control RR-CX100.
The RR-CX100 can be congured to use IR codeset 1 or IR codeset 2 in case
the unit is conicting with other Rotel models. Push and hold the TUNER
button and 1 (or TUNER and 2 for codeset 2) at the same time and hold for
approximately 5 seconds until the backlights on the remote control blink on
then off then release both buttons. This sets the remote control to use codeset
1 (or codeset 2 if TUNER and 2 are held). The System menu in the OSD
includes a conguration option to set the processor to either codeset 1 or
codeset 2. The factory default for the remote and processor is codeset 1.

The RR-CX100 can also control an attached Rotel CD player. The CD player
functions include Play, Stop, Pause, Track Forward, Track Back, Fast Forward,
Fast Reverse. To activate these functions press the CD button on the remote.
If the CD is attached to the XLR source input, these functions can be activated
by pressing the XLR button. To change the CD player functions to operate
after pressing the XLR button press and hold the XLR and 1 button for 5
seconds until the backlight LEDs blink twice times then release. To disable
XLR sending the CD control functions press and hold the XLR and 0 button
for 5 seconds until the backlight blinks.

The transport buttons will only operate for CD control after the CD or XLR
button is pressed on the remote. If a different input is selected from the
remote these buttons will no longer send the CD transport IR commands.

Overview of Buttons and Controls

Input Buttons 4qM

The input source can be changed by pressing the desired source input
buttons on the front panel or remote control.

SUR+ Buttons 9B

The SUR+ buttons on the remote control or front panel will display surround
mode information of currently selected source. The default DSP mode can
be congured in the Setup menu for each source. Press the SUR+ button
repeatedly to toggle through the available DSP modes.

DSP processing options vary depending on the selected source input type.
Not all DSP options are available in analog or digital input modes.

Other buttons on the remote can directly access specic DSP modes.

2CH: Changes the audio mode to STEREO, DOWN MIX.
BYPASS: Bypass all DSP processing.
PLCM: Selects Dolby ATMOS surround mode.

Playback Control buttons L

These buttons provide basic control functions for iPod AUDIO playback.
The control buttons can also control Rotel CD players. For more information
how to congure CD controls see the REMOTE CONTROL OVERVIEW
section of the manual. Supported functions include Play, Stop, Pause, Next
Track, Previous Track.

DIM Button J

Use this button to dim the front panel display.

This section provides a basic overview of the buttons and controls on the
front panel and the remote control. Detailed instructions on the use of these
buttons are provided in the more complete operating instructions in the
following sections.

STANDBY 1 and Power ON/OFF Buttons A

The front-panel STANDBY button and the remote control ON/OFF button
activate or deactivate the unit. The rear panel master POWER switch must
be on the ON position for the remote standby function to operate.

VOLUME Knob and VOLUME UP/DOWN Buttons =D

The VOLUME UP/DOWN buttons on the remote and the large rotary control
on the front panel provide the master VOLUME control, adjusting the output
level of all channels simultaneously including mute and volume level 1 to 96.

DISPLAY (DISP) Button 0B

Push this button to toggle through device status on the VFD and TV.

SETUP Button H
Navigating and ENTER Buttons

The SETUP button displays the OSD setup screen on the HDMI OSD enabled
output. Push the SETUP button again to deactivate this menu. Use the
navigation buttons Up/Down/Left/Right and ENTER on the remote control
to access the various menus.

I

MUTE Button -F

Push the MUTE button once to turn the sound off. An indication appears in
the front panel and on-screen display. Press the button again to restore the
previous volume level.

Adjustment made using the J button is temporary only and not saved
after power off.

SUB, CTR, REAR Buttons B

These buttons can access the speaker setting and adjust the output level for
speakers in the system. Use the Up and Down arrow buttons on the remote
control to change values. This is only a temporary change. To make permanent
adjustments, please access the SPEAKER LEVEL SETUP menu from the OSD.

MEM Button E

This button does not operate with the RSP-1576 and is used only to control
a Rotel tuner product for preset memory control.

LIGHT Button N

Pushing this button turns on the back light of the remote control for easy
operation in dimly lit rooms.

ASSISTIVE LIGHT O

Push and hold on the LIGHT Button N for 3 seconds to turn on the assistive
light. This light can be used to help locate objects in a dimly lit room such
as a home theatre surrounding. The light will remain illuminated as long
as the button is held.

Automatic Surround Modes

Decoding of digital sources connected is generally automatic with detection
triggered by a “flag” embedded in the digital recording telling the processor
what decoding format to use. For example, when a Dolby or DTS surround
signal is detected, the processor activates the proper decoding.

19

The processor will recognize a digital signal with Dolby Surround encoding
and activate Dolby® decoding. Additionally, you can configure a default
surround mode for each input using the INPUT SETUP menu (see the Setup
section of this manual). Combined with the auto-detection of Dolby Digital
and DTS, this default surround setting makes operation of the processor’s
surround modes totally automatic.

For stereo inputs such as CD and Tuner, you could select BYPASS or STEREO
mode as the default for 2-channel playback or a DSP mode if you prefer to
hear music sources in surround sound.

NOTE: A digital signal coming into the processor will be recognized and
properly decoded. However, on a Blu-ray with multiple soundtracks, you
may need to configure the player for the desired signal and encoding type.
For example, you may need to use the player’s menu system to select the
desired Dolby Digital or DTS soundtrack.

Manually Selecting Surround Modes

For users who prefer a more active role in setting surround modes, buttons
on the remote and the front panel provide manual selection of surround
modes that are not automatically detected or, in some cases, to override
an automatic setting.

Manual settings available from the front panel and/or the remote control
should be used when you want to play:

• Standard 2-channel stereo (Left/Right speakers, and depending upon
speaker settings also subwoofer) with no surround processing.

• Down mixed 2-channel playback of Dolby Digital 5.1 or DTS recordings.

To change the surround mode press the SUR+ button on the remote control
or front panel control to toggle through the available surround options. The
2CH button on the remote control will create a down mix of any multichannel
signal to 2 channel stereo mode.

NOTE: Not all surround modes are available for all surround source
formats. The input source signal will determine the available surround
options that can be selected.

Analog Stereo

This type of recording includes any conventional stereo signals from the
processor’s analog inputs, including analog audio from CD players, FM
tuners, etc.

Analog stereo inputs require a choice about how the signal is routed through
the processor. One option is the ANALOG BYPASS mode. In this mode, the
stereo signal is routed directly to the volume control and the outputs. This
mode is pure 2-channel stereo, bypassing all of the digital circuitry. None
of the bass management features, speaker level settings, EQ settings, or
delay settings is active. There is no subwoofer output. A full-range signal is
sent directly to the front left and right speakers.

Alternatively, a DSP mode can be enabled, this converts the analog
inputs to digital signals, passing them through the digital processors in the
RSP-1576. This option allows all of the features to be active including bass
management settings, crossovers, subwoofer outputs, EQ settings, etc. There
are several DSP modes available including: 2-CH Stereo, Dolby 3-Stereo,
5-CH Stereo, 7-CH Stereo, 9CH and 11CH Stereo, Dolby ATMOS Surround
and Dolby Neural:X modes.

To change the surround mode press the SUR+ button on the remote control
or front panel control to toggle through the available surround options.

• Dolby 3-channel stereo (Left/Right/center) of 2-channel recordings.

• 5-channel stereo, 7-channel, 9-channel or 11-channel from 2-channel
recordings.

• Other modes may be available depending on the system conguration
and active source material.

• PCM 2-channel (non 96kHz) digital signals can be overridden to Dolby
3-Stereo, 5CH Stereo, 7CH Stereo, 9CH, and 11CH and Stereo as
well as Dolby Atmos and DTS Neural:x.

To change the surround mode press the SUR+ button on the remote control
or front panel to toggle through the available options. The 2CH button on
the remote control will create a down mix of any multichannel signal to 2
channel stereo mode.

NOTE: Not all surround modes are available for all surround source
formats. The input source signal will determine the available surround
options that can be selected.

Digital Audio

You can play these recordings in BYPASS, 2-CH Stereo, Dolby 3-Stereo, 5-CH
Stereo, 7-CH Stereo, 9CH Stereo, 11CH Stereo, Dolby ATMOS Surround
and Dolby Neural:X modes.

All of the bass management settings (speaker size, subwoofer, and crossover)
are in effect with digital stereo inputs unless BYPASS mode is selected.

NOTE: Not all surround modes are available for all surround source
formats. The input source signal will determine the available surround
options that can be selected.

Basic Operation

This section covers the basic operating controls of the RSP-1576 and the
remote control.

Selecting Inputs

You can select any of the source inputs for listening and/or watching: VIDEO
1 - 7, CD, PHONO, XLR, MULTI INPUT, USB, PC-USB, BLUETOOTH or TUNER.

The source inputs can be customized using the INPUT SETUP menu to assign
which HDMI input to use as the video source. Video 1- 7 inputs can also
be congured to accept any analog and digital audio sources. The default
of audio source is set to HDMI Audio.

When you have congured the source input, you can use Input buttons to
select the desired inputs:

1. Press the Input buttons on the front panel 4q to switch to the selected

source input i.e. CD, Tuner, Video 1 etc...

2. Press the source input button on the remote control M to select the

desired source.

20

RSP-1576 Surround Sound Processor

USB/iPod Operation

iPod/iPhone Connection 5

1. An iPod/iPhone can be connected using the proper USB cable to the

USB front socket of the RSP-1576.

2. The iPod/iPhone will stream a digital music signal to the unit. Music

selection and playback control are available using the iPod/iPhone.

3. The iPod/iPhone screen will remain active while connected to the unit.

Playback Control Buttons L

Transport controls are available from the remote control during playback
including play, stop/pause, next track, previous track.

Bluetooth

Bluetooth Connection

The Bluetooth feature allows you to stream music wireless from your Bluetooth
enabled device, i.e. mobile phones. Select the BLUETOOTH (BT) input on
the RSP-1576. From your device (mobile phones etc.) activate Bluetooth and
allow it to search for other Bluetooth devices. Select “Rotel Bluetooth” and
connect to it. Once connected you can start streaming music to the RSP-1576.

NOTE: The RSP-1576 Bluetooth is APTX compatible. This enables you
to stream music at lossless CD quality.

NOTE: Some Bluetooth devices may require you to establish connection
again with the RSP-1576 if the unit was powered off. If this occurs,
please go through the above steps to re-connect.

Rear PC-USB

Rear PC-USB Connection

The rear USB socket labeled PC-USB accepts a type B USB plug. This input
accepts PCM audio signals sent from your computer up to 24 bits/192kHz
resolution.

Menu Basics

Navigation Buttons

The following remote control buttons are used to navigate the OSD menu
system:

SETUP button: Press to display the MAIN MENU. If a menu is already
visible, push this button to close the OSD and return to normal operation.

Up/Down buttons: Press to move up and down in the lists of menu items
that appear on the OSD screens.

Left/Right buttons: Press to change the current settings for a selected menu
item on OSD screens.

ENTER button: Press ENTER to confirm a setting.

BACK Button: Press BACK to go back to the previous menu.

Main Menu

MAIN MENU

INPUT SETUP
AUDIO CONFIGURATION
SPEAKER CONFIGURATION
SPEAKER DISTANCE SETUP

SUBWOOFER SETUP
SPEAKER LEVEL SETUP
VIDEO SETUP
PEQ CONFIGURATION
SYSTEM SETUP

EXIT

Setup

The Rotel RSP-1576 features two types of information displays to help operate
the system. The first consists of simple status displays that appear on the
TV screen whenever primary settings (Volume, Input, etc.) are changed.

A more comprehensive ON-SCREEN DISPLAY (OSD) menu system is available
at any time by pressing the SETUP H button on the remote. These OSD
menus guide you through the configuration and setup of the RSP-1576. The
settings made in the configuration process are memorized as default settings
and need not be made again for normal operation of the unit.

The OSD menus can be configured to display several different languages.
The default English version of all main menus are shown at the front of this
manual. If your language is available, those menus will be shown in the
instructions. If you would like to change from the default English language
before proceeding, go to the instructions for the SYSTEM SETUP menu later
in this manual. From this menu, you can change the language display.

The MAIN MENU provides access to OSD screens for various configuration
options. MAIN MENU is reached by pressing the SETUP H button on the
remote. To select the desired menu, move the highlight using the Up/Down
arrow buttons and press the ENTER button on the remote control. Press the
SETUP button again or select “EXIT“ on the OSD to end setup and return
to normal operation.

Configuring Inputs

A key step in setting up the unit, is to configure each source input using the
INPUT SETUP screens. Configuring the inputs allows you to set defaults for a
number of settings including the type of input connector, the desired surround
mode, custom labels that appear in the displays when a source is selected,
and many more. The following OSD menus are used to configure the inputs.

21

Input Setup

INPUT SETUP

SOURCE
NAME
VIDEO INPUT
AUDIO INPUT
TRIGGER OUTPUT
DEFAULT MODE
AUDIO DELAY
LEVEL ADJUST

BACK

The INPUT SETUP menu configures the source inputs and is accessed from
the MAIN menu. The screen provides the following options, selected by
placing the highlight on the desired line using the Up/Down arrow buttons:

SOURCE: Changing this input allows you to select a specic input for
conguring (CD, TUNER, VIDEO 1–7, USB, PC-USB, XLR, PHONO, MULTI
INPUT and BLUETOOTH).

NAME: The name of the source can be customized. For example VIDEO1
can be named “TV” for easier reference. The default NAME is the same
as the SOURCE. Place the highlight on this option and press ENTER on the
remote control, it will then take you to the SOURCE NAME EDIT sub menu.

1. Press the Left/Right arrow buttons on the remote control to change the
first letter, scrolling through the list of available characters.

2. Press the ENTER button on the remote control to confirm that letter and
move to the next position.

3. Repeat steps 1 and 2 until all eight characters have been completed.
The final press of the ENTER button saves the new name. Or select
the “8 “ button on the screen to conrm if you have less than eight
characters to enter.

VIDEO INPUT: Selects the video source to be displayed on the TV monitor.
Assign the input to a source component you have connected by selecting
from HDMI 1–6 and HDMI Front. For audio only sources (such as a CD
player), you would typically specify OFF so that no video is displayed. The
video source can also be set to “Last Video Source” so when switching to
the specied Video input the previous Video source is not changed. This
feature is useful if you want to change only the audio and keep watching
whatever was the last displayed video source.

VIDEO 1
VIDEO 1
HDMI Audio

Mul Input

1 _ _

Source Dependent

0m sec
0dB

TRIGGER OUTPUT: The RSP-1576 has three 12V trigger outputs (labeled 1
– 3) that supply a 12V DC signal to turn on other components as needed.
This menu item turns on specific 12V trigger outputs whenever the indicated
input source is selected. For example, congure the VIDEO 1 input to turn
on the 12V trigger for your DVD player. Any combination of trigger outputs
can be programmed for each source.

1. Place the highlight on the option “TRIGGER OUTPUT“ and press the
ENTER button on the remote control.

2. Press the Up/Down arrow buttons on the remote control to change the
first position from blank to 1 (activating TRIGGER 1 for that source)
and use the Left/Right arrow buttons to move to the next position.

3. Repeat until all three positions are set as desired. The final press of
the ENTER button confirms the selection.

NOTE: The 12V trigger output 1 is defaulted to be turned on for all
input sources. You can turn it off by following the steps as above.

DEFAULT MODE: The DEFAULT MODE setting allows you to set a default
audio mode for each source input. The default setting will be used unless the
source material triggers automatic decoding of a particular type or unless
the default setting is temporarily overridden by the front panel or remote
surround mode buttons.

Options for the default surround modes are: Stereo, Dolby 3 Stereo, 5
channel Stereo, 7 channel Stereo, 9 channel Stereo, 11 channel Stereo,
Dolby ATMOS Surround, DTS Neural:X, Analog Bypass (for analog input
only) and Source Dependant.

NOTE: Most types of digital discs or source material are generally
detected automatically and the proper decoding activated with no
action or setting required.

Since Dolby and DTS sources are detected and decoded automatically, the
default setting typically tells the unit how to process a 2-channel stereo signal.
For example, you might have your CD input default to 2-channel stereo, DVD
and game console inputs default to Dolby processing for surround material,
and TUNER input default to 5 Channel Stereo mode.

In some cases, the default setting can be manually overridden by the 2CH,
BYPASS and SUR+ button on the remote control or front panel, or PLCM button
on the remote control. See the Manually Selecting Surround Modes section
of this manual for more information on which settings can be overridden.

AUDIO INPUT: Assigns a physical input connection for the source displayed
in the first line of the menu. Options include Optical 1–3, Coax 1–3, HDMI
Audio, Tuner, Multi Input, XLR, Phono, CD, Bluetooth, PC-USB, USB, ARC,
AUX or Off.

NOTE: Optical, Coaxial,CD and XLR inputs can be assigned to the
CD input source or Video 1-7. Audio input is not available to the XLR,
PHONO, MULTI INPUT, BLUETOOTH or USB input source.

When selecting the input source for “PC-USB”, AUDIO INPUT can be
changed to “USB Audio 1.0” or “USB Audio 2.0”. USB Audio Class 2.0
may require installation of the PC driver. For more information please see
PC-USB section in this manual.

AUDIO DELAY: Also known as “lip-sync” delay, this setting delays the audio
signal for an input by the specified amount to match the video input. This
feature can be useful when the video signal is delayed more than the
audio signal.

The range of available settings is from 0 ms to 500 ms, in 10 ms steps. The
setting is individually stored for each input and is the default Audio Delay
each time that input is selected.

LEVEL ADJUST: Use this feature to set the volume level lower than the other
inputs. This feature is useful for sources that are consistently higher in volume
than other sources in the system.

Valid settings include: 0 to -6 dB, in 0.5 dB steps.

22

RSP-1576 Surround Sound Processor

FIXED VOLUME: Congures a Fixed Volume level for a specied input. To
enable this feature, select the desired xed volume level for USB, PC-USB,
Bluetooth, Coax 1 or Optical 1. When enabled and the input with a Fixed
Volume is selected, the Volume level will immediately be set to the specied
level. Fixed volume: Variable is factory default.

Valid settings include: Variable, 1 - 96.

NOTE: The Volume knob on the front panel and Volume +/- buttons
on the IR remote are disabled when the volume is Fixed. To disable this
feature set the Fixed Volume level to “Variable”.

Press the SETUP button on the remote control to exit the menu and return
to normal operation.

Multi Input Setup

INPUT SETUP

SOURCE
NAME
VIDEO INPUT

TRIGGER OUTPUT

LEVEL ADJUST

BACK

MULTI INPUT
M-INPUT
HDMI1

1 _ _

0dB

When the MULTI INPUT source is selected on the INPUT SETUP menu, the
available options change to reflect the fact that these inputs are direct analog
inputs and bypass the unit’s digital processing. The AUDIO INPUT, DEFAULT
MODE and AUDIO DELAY options are not available since these functions
are processed digitally and not available to the MULTI INPUT source.

Configuring Audio

Audio Conguration

Understanding Speaker Configuration

Home theater systems vary in the number of speakers and the bass capabilities
of those speakers. This processor offers surround modes tailored to systems
with various numbers of speakers and bass management features which send
bass information to the speaker(s) best able to handle it – subwoofers and/
or large speakers. For optimum performance, you must tell the processor
the number of speakers in your system and how bass should be distributed
among them.

The following configuration instructions refer to LARGE and SMALL speakers,
referring more to their desired bass configuration than their physical size.
Specically, use the LARGE setting for speakers that you want to play deep
bass signals. Use the SMALL designation for speakers that would benefit
from having their bass sent to more capable speakers. The bass management
system redirects bass information away from all SMALL speakers and sends
it to the LARGE speakers and/or the SUBWOOFER. It may be useful to think
of LARGE as “full-range” and SMALL as “high-pass filtered.”

• Five LARGE speakers and subwoofer: This system requires no bass
redirection. All five speakers play the normal bass recorded in their
respective channels. The subwoofer plays the normal channel bass.
Meanwhile the normal bass places higher demands on the capabilities
of the other speakers and the ampliers driving them.

• LARGE front, center, surround speakers, no subwoofer: The normal
bass from the front, center, and surround channels is played in its
respective speakers.

• All SMALL speakers and subwoofer: The normal bass from all channels
is redirected to the subwoofer. The subwoofer handles ALL of the bass
in the system. This configuration provides several benefits: deep bass
is played by the speaker most suited to do so, the main speakers may
play louder with less distortion, and the need for amplier power is
reduced. This configuration should be used with bookshelf-size or
smaller main speakers. It should also be considered in some cases
with floorstanding front speakers. This configuration is advantageous
when driving the system with moderate power ampliers.

AUDIO CONFIGURATION

CONFIGURATION

FRONT
CENTER
SUBWOOFER
SURROUND
CENTER BACK
HEIGHT 1
HEIGHT 2
BACK

7.1.4

Front
Center
Subwoofer
Surround
Center Back
Overhead Front
Overhead Rear

The AUDIO CONFIGURATION menu configures the preamplier RCA outputs.
The screen provides options from 5.1 to 7.1.4 and an option for 5.1 with
Bi-Amplication. After selecting the desired conguration, the preamplier
RCA output audio signal connections are displayed for up to 12 channels.

Configuring Speakers and Audio

This section of the setup process covers items concerning audio reproduction
such as the number of speakers, bass management including subwoofer
crossovers, establishing equal output levels for all channels, delay settings,
and parametric EQ.

• LARGE front speakers, SMALL other speakers, and a subwoofer: The
normal bass from the SMALL center and surround speakers is redirected
to the LARGE front speakers and the subwoofer. The LARGE front
speakers play their own normal bass plus the redirected bass from
the SMALL speakers. The subwoofer plays the redirected bass from
all of the other channels. This might be an appropriate configuration
with a pair of very capable front speakers. A potential disadvantage
with mixed LARGE and SMALL congurations is that the bass response
may not be as consistent from channel to channel as it might be with
the all SMALL configuration.

Speaker Conguration

SPEAKER CONFIGURATION

FRONT
CENTER
SURROUND
SUBWOOFER
CENTER BACK
OVERHEAD FRONT
OVERHEAD REAR
ADVANCED SETUP
BACK

Large
Small
Small
Yes
None
None
None

23

The SPEAKER CONFIGURATION menu is used to configure the RSP-1576 for
use with your specific loudspeakers and to determine the bass management
configuration as described in the previous overview. The menu is accessed
from the MAIN menu. The Audio Conguration will determine which speakers
are displayed in the Speaker Conguration menu.

The following speaker options are available:

FRONT SPEAKERS (Small/Large): Use the “Large” setting to have the front
speakers play low bass (full-range). Use the “Small” setting to redirect
normal bass away from these speakers to a subwoofer (high-pass filtered).

CENTER SPEAKER(S) (Large/Small/None): Select the “Large” setting (not
available with SMALL front speakers) to have the center speaker play low
bass (full-range). Select the “Small” setting if your center channel speaker
has limited low frequency capability, or if you prefer that the bass be sent
to the subwoofer (high-pass). Select the “None” setting if your system does
not have a center channel speaker (the surround modes will automatically
divide all center channel information equally between the two front speakers,
creating a phantom center channel).

SURROUND SPEAKERS (Large/Small/None): Select the “Large” setting (not
available with SMALL front speakers) to have the surround speakers play
low bass (full-range). If your rear speakers have limited bass capability
or if you would prefer that the bass go to a subwoofer, select the “Small”
setting (high-pass). If your system has no rear surround speakers, select the
“None” setting (surround channels are added to the front speakers so none
of the recording is lost).

SUBWOOFER (Yes/Max/No): The “Yes” setting is the standard setting if your
system has a subwoofer. If your system does not have a subwoofer, select
“No”. Select the “Max” setting for maximum bass output with normal bass
being duplicated by both the subwoofer and any LARGE speaker in the system.

CENTER BACK (1Large/1Small/2Large/2Small/None): Some systems have
one or two additional center back surround speakers. Select the “Large”
setting (not available with SMALL front and surround speakers) to have
your center back speaker(s) play low bass. Use “1Large” if you have one
center back speaker (6.1) or “2Large” (7.1) if you have two center back
speakers (7.1). If your center back speakers have limited bass capability or
if you would prefer that the bass go to a subwoofer, use the “Small” setting
(“1Small” for one speaker, “2Small” for two speakers). If your system has
no center back speakers, select the “None” setting.

OVERHEAD FRONT (Large/Small/None): Select the “Large” setting (not
available with SMALL front and surround speakers ) to have your overhead
front speakers play low bass. If you would prefer that the bass go to a
subwoofer, use the “Small” setting.

OVERHEAD REAR (Large/Small/None): Select the “Large” setting (not
available with SMALL front , top front and surround speakers ) to have your
overhead rear speakers play low bass. If you would prefer that the bass go
to a subwoofer, use the “Small” setting.

ADVANCED: Speaker configuration is generally a global setting for all surround
modes and need only be done once. However, for special circumstances,
the processor provides the option of setting the speaker configuration
independently for each surround mode. Select the ADVANCED SETUP line
on the menu and press ENTER to go to the ADVANCED SPEAKER SETUP
menu described in the following section.

To change a setting on the SPEAKER CONFIGURATION menu, place the
highlight on the desired line using the Up/Down arrow buttons and use the
Left/Right arrow buttons to toggle through the available settings. To return to
the MAIN menu, select “BACK” on the OSD and press the ENTER button,
or press the BACK button. Press the SETUP button, or select “EXIT” on the
OSD to exit setup and return to normal operation.

Advanced Speaker Setup

ADVANCED SPEAKER SETUP

SPEAKER
CROSSOVER
DOLBY
DTS
STEREO
BACK

In most cases, the standard speaker configuration described above is a global
setting and can be used for all surround modes. However, the processor
provides the capability to customize these settings for three different modes:
Dolby, DTS, and Stereo. In addition, the ADVANCED SPEAKER SETUP
allows you to select a customized high-pass crossover frequency for the
front, center, surround, surround back speakers.

NOTE: In most systems, the default settings on this menu will provide
the most predictable results and most users will not need to change
any settings. You should fully understand bass management and have
a specific reason for needing a custom configuration before changing
these settings. Otherwise, skip to the following topic, SUBWOOFER
SETUP.

The available settings on the ADVANCED SPEAKER SETUP menu are as follows:

SPEAKER (Front/Center/Surround/Center back/Overhead Front/Overhead
Rear/Subwoofer): Select the set of speakers to be configured with custom

settings.

CROSSOVER (40Hz/50Hz/60Hz/70Hz/80Hz/90Hz/100Hz/120Hz/150Hz
/200Hz/OFF): This setting for the high-pass and low-pass crossover point is

only active for SMALL speakers settings and the subwoofer. When you first
access the ADVANCED SPEAKER SETUP menu, the current crossover point
will be shown on this line which is set to “100Hz” as the factory default.
Change the value of this line only if you want the current speaker to have a
different crossover point. This setting ONLY affects redirected bass.

NOTE: The “OFF” setting (available only for the subwoofer) sends
a full-range signal to your subwoofer so that you can use its built-in
low-pass filter.

NOTE: When a speaker is set to “Large” on the SPEAKER
CONFIGURATION menu or on this menu, the crossover setting has no
effect since, by definition, a LARGE speaker plays full-range with no
bass redirection to the subwoofer and no crossover. In addition, the
CROSSOVER setting is not available for the MULTI INPUT.

DOLBY (Default/Large/Small/None): Sets the current speaker (shown in the
first line) to Large, Small, or None, overriding the setting from the SPEAKER
SETUP menu. If you want to use the speaker size setting set in the SPEAKER

Front
100Hz
Default
Default
Default

24

RSP-1576 Surround Sound Processor

SETUP menu, select “Default”. The “None” setting is not available for
FRONT speakers.

DTS (Default/Large/Small/None): The same options described for Dolby
above, except these settings ONLY take effect with DTS decoding.

STEREO (Default/Large/Small/None): The same options described for Dolby
above, except these settings ONLY take effect in STEREO surround mode.

For the subwoofer, the above selections for DOLBY, DTS, and STEREO
become “Yes/No/Default”. They will be set to “Default” if the front speakers
are set to “Default”, and they would be set to “Yes” if the front speakers
are set to “Small”.

NOTE: When the front speakers are set to use the default settings on
the ADVANCED SPEAKER SETUP menu, the specific “Large/Small/
None” settings of DOLBY, DTS or STEREO are not available for the
other speakers. These speakers will use the default settings.

Subwoofer Setup

SUBWOOFER SETUP

DOLBY
DTS
STEREO
MULTI LPCM
MULTI INPUT
BACK

0dB
0dB
0dB
0dB
0dB

To return to the main menu select “BACK” on the OSD or push the BACK
button on the remote control.

Speaker Level Setup

SPEAKER LEVEL SETUP

FRONT LEFT
CENTER
FRONT RIGHT
SURROUND RIGHT
CENTER BACK RIGHT
OVERHEAD FRONT RIGHT
OVERHEAD REAR RIGHT
OVERHEAD REAR LEFT
OVERHEAD FRONT LEFT
CENTER BACK LEFT
SURROUND LEFT
SUBWOOFER
BACK

NOTE: If you have configured your system to use two center back
speakers, there will be an additional line in the menu, giving you the
ability to independently adjust the CENTER BACK LEFT and CENTER
BACK RIGHT speakers.

This menu uses filtered pink noise test tones to set equal volume levels for
all speakers (FRONT LEFT, CENTER, FRONT RIGHT, SURROUND RIGHT,
CENTER BACK RIGHT, CENTER BACK LEFT, OVERHEAD FRONT RIGHT,
OVERHEAD REAR RIGHT, OVERHEAD REAR LEFT, OVERHEAD FRONT LEFT,
SURROUND LEFT and SUBWOOFER) to ensure proper surround sound
reproduction. Setting the output levels using the test procedure provides the
most accurate adjustment so that digital surround sound material will be
reproduced as it was intended and is a critical step in calibrating the system.
The Audio Conguration will determine which speakers are displayed in
the Speaker Level Setup menu.

0dB
0dB
0dB
0dB
0dB
0dB
0dB
0dB
0dB
0dB
0dB
0dB

These five lines allow you to override the subwoofer level setting as
determined in the Speaker Level Setup menu (see next section) for each
specic surround mode.

DOLBY
DTS
STEREO
MULTI LPCM
MULTI INPUT

Use the Up/Down arrow buttons to move to the specic surround mode and
use the Left/Right arrow buttons to adjust the subwoofer level for the current
surround mode. The options are a range of adjustments from -9 dB to +9
dB and MAX (+10 dB). A setting of 0 dB means that the specified surround
mode will use the master subwoofer level. Any other setting is an offset to
the master setting. For example, an adjustment of -2 dB for a particular
surround mode means that the subwoofer level will be 2 dB quieter than
the master subwoofer level when that surround mode is selected. Use these
subwoofer level settings to adjust the relative bass output of various surround
modes. Changing the master subwoofer level will increase or decrease the
level for all surround modes.

We recommend starting with the settings for all surround modes at the
default 0 dB setting during the speaker level calibration of the system and
for a period of familiarization after that. As you listen to a variety of source
material over time, you may notice that certain surround modes consistently
produce too much or too little bass from the subwoofer. If so, then use these
menu settings to customize each surround mode. In general, if the master
subwoofer level is set properly (i.e. not too loud), individual settings for
each surround mode should not be necessary.

When you enter the SPEAKER LEVEL SETUP menu, you will hear a test tone
coming from the highlighted speaker. Highlight different speakers by moving
the cursor to the desired line using the Up/Down arrow buttons. The test
tone will shift accordingly to the selected speaker.

Seated in the normal listening location, shift the test tone to the various
speakers. Using the one speaker as a reference, listen for any speakers that
are noticeably louder or quieter. If so, adjust that speaker’s levels up or down
(in 0.5 dB increments) using the Left/Right arrow buttons. Continue switching
among the speakers and adjusting until all speakers are the same volume.

To return to the MAIN menu, select “BACK“ on the OSD or press the BACK
button. Press the SETUP button or select “EXIT“ on the OSD to exit setup
and return to normal operation.

Calibration with an SPL meter:

Calibrating the system with an SPL (Sound Pressure Level) meter, rather than
by ear, provides more precise results and improves the system’s performance
signicantly. Inexpensive SPL meters are widely available and the procedure
is quick and easy.

Both Dolby and DTS specify a standard calibration level for all theaters
to ensure that soundtracks can be played at the volume level intended by
the director of the film. This reference level should result in spoken dialog
played at a realistic level for normal speech with the loudest peaks in any
single channel at about 105 dB. The RSP-1576’s test tones are generated at
a precise level (-30 dBFs) relative to the loudest possible digitally recorded
sound. At the Dolby or DTS reference level, these test tones should produce
a 75 dB reading on an SPL meter.

25

Set the meter to its 70 dB dial setting with SLOW response and C-weighting,
held away from your body at your listening position (mounting the SPL
meter on a camera tripod makes this easier). You can point the SPL meter
at each speaker as it is being measured; however, positioning the meter
in a fixed position pointing at the ceiling is easier and probably produces
more consistent results.

Increase the master volume control on the unit until the meter reads 75 dB
(+5 dB on the meter scale) when playing the test tone through one of the
front speakers. Then, use the individual channel adjustments on the SPEAKER
LEVEL SETUP menu to adjust each of the individual speakers, including the
subwoofer, to the same 75 dB on the SPL meter.

NOTE: Due to meter weighting curves and room effects, the actual
level of the subwoofer may be slightly higher than you measure. To
compensate, Dolby suggests setting the subwoofer several dB lower
when calibrating with an SPL meter (i.e. set the subwoofer to read 72
dB on the meter instead of 75 dB). Ultimately, the proper subwoofer
level must be determined by personal taste and some listeners prefer
to set it above 75 dB for film soundtracks. Exaggerated bass effects
come at the expense of proper blending with the main speakers and
place stress on the subwoofer and its amplifier. If you can localize
bass from the subwoofer, the subwoofer level may be too high. Music
can be useful for fine-tuning the subwoofer level as excessive bass is
readily apparent. The proper setting will generally work well for music
and movie soundtracks.

in 0.25 foot (0.075 m) increments with each increment equivalent to an
additional delay of 0.25 ms.

To change a setting, place the highlight on the desired line using the Up/
Down arrow buttons and use the Left/Right arrow buttons to increase or
decrease the delay. To return to the MAIN menu, press the BACK button or
select “BACK“ on the OSD. Press the SETUP button or select “EXIT“ on the
OSD to exit setup and return to normal operation.

Miscellaneous Settings

System Setup

SYSTEM SETUP

LANGUAGE
IR REMOTE CODESET
PEQ FUNCTION
DISPLAY
POWER OPTION
NETWORK CONFIGURATION
SOFTWARE INFORMATION
RESTORE FACTORY DEFAULT
BACK

This SYSTEM SETUP menu, reached from the MAIN menu, provides access
to several miscellaneous settings as follows:

English
Codeset 1
Disable
HDMI And VFD

Remember the setting of the master volume control used during this calibration.
To play a Dolby Digital or DTS soundtrack at the reference volume level,
simply return to that volume setting. Note that most home theater listeners
find this setting to be excessively loud. Let your own ears be the judge for
deciding how loud to playback movie soundtracks and adjust the master
volume control accordingly. Regardless of your listening levels, using an SPL
meter to calibrate equal levels for all speakers in the system is recommended.

Speaker and Delay/Distance Setup

SPEAKER DISTANCE SETUP

FRONT LEFT
CENTER
FRONT RIGHT
SURROUND RIGHT
CENTER BACK RIGHT
OVERHEAD FRONT RIGHT
OVERHEAD REAR RIGHT
OVERHEAD REAR LEFT
OVERHEAD FRONT LEFT
CENTER BACK LEFT
SURROUND LEFT
SUBWOOFER
BACK

The SPEAKER DISTANCE SETUP menu, which is reached from the MAIN
menu, allows you to set the delay for individual speakers. This ensures that
the sound from each speaker arrives simultaneously at the listening position,
even when the speakers are not all placed at equal distances from the
listener. Increase the delay to speakers located closer to the seating area
and decrease the delay to speakers located farther from the seating area.
The Audio Conguration will determine which speakers are displayed in
the Speaker Distance Setup menu.

10.00 FT 3.05M

10.00 FT 3.05M

10.00 FT 3.05M

10.00 FT 3.05M

10.00 FT 3.05M

10.00 FT 3.05M

10.00 FT 3.05M

10.00 FT 3.05M

10.00 FT 3.05M

10.00 FT 3.05M

10.00 FT 3.05M

10.00 FT 3.05M

LANGUAGE: Selects a language for the On Screen Display.

IR REMOTE CODESET: The RSP-1576 has two IR codesets and can be changed

in the event there is a conict of IR codes with other Rotel products.

NOTE: After changing the IR REMOTE CODESET the remote must
also be changed to continue using the remote control. Push and hold
the TUNER button and 1 (or TUNER and 2 for codeset 2) at the same
time and hold for approximately 5 seconds until the backlights on the
remote control blink on then off then release both buttons. This sets the
remote control to use codeset 1 (or codeset 2 if TUNER and 2 are held).

PEQ FUNCTION: Turns the PEQ function On or Off.

DISPLAY: Sets the information shown on the main HDMI OSD and front VFD

display. Settings are “Off”, “HDMI Only”, “VFD Only“ or “HDMI And VFD”.

POWER OPTION: Access to conguration of Off Timer, Max Power On
Volume, Power Mode and Signal Sense Input.

POWER OPTION

OFF TIMER
MAX POWER ON VOLUME 45

POWER MODE
SIGNAL SENSE INPUT
BACK

20 MINS

Normal
Disable

This Rotel processor makes setting the delay time for each speaker very
easy. Simply measure the distance (in feet or meters) from your seating
position to each speaker in your system. Set the measured distance in the
line for each speaker. The menu provides a line for each speaker configured
in your system and gives a range of settings up to 33 feet (10.06 meters)

26

RSP-1576 Surround Sound Processor

OFF TIMER: Set the amount of time the units stays powered on when there
is no audio signal. The RSP-1576 will automatically go to standby mode
if audio is not detected for the specied timer period. Default: 20 MINS.

Valid settings include: Disable, 20 MINS, 1 Hour, 2 Hours, 4 Hours.

MAX POWER ON VOLUME: Species the maximum volume level to be
used each time the unit powered on. Valid settings include: 20 - 70.
Default: 45.

POWER MODE: Enables the rear panel USB power port to remain
powered at all times. The power consumption is higher in Quick Power
mode. To enable continuous power to the rear USB power port select
the Quick option.

Valid settings include: Normal, Quick.

NOTE: When the POWER MODE is configured to Quick, the RSP-1576
will consume additional power in standby mode.

SIGNAL SENSE INPUT: Checks if a digital audio signal is present on
the congured Signal Sense Input. When this input is selected as the
active listening source, the RSP-1576 monitors the digital data stream to
determine if there is audio. If there is no audio detected for 10 minutes,
the RSP-1576 will enter Signal Sense Standby Mode. When in Signal
Sense Standby Mode and the RSP-1576 detects audio on Signal Sense
Input, the unit will automatically power on. To disable this function, select
the DISABLE option which is the factory default setting.

NOTE: The Signal Sense function is not available if Standby Video
Source is enabled.

NOTE: When the RSP-1576 enters standby mode via the remote
control, the Signal Sense function will not operate until the unit detects
the audio has stopped for the minimum 10 minute time-out period. This
prevents the unit from immediately powering back on if there is still
active audio playing.

NOTE: When the SIGNAL SENSE INPUT function is activated, the
RSP-1576 will consume additional power in signal sense standby mode.

NETWORK CONFIGURATION: Sets the network conguration for the unit. In
most systems, set the IP ADDRESS MODE to DHCP. This setting will allow
your router to assign an IP address to the RSP-1576 automatically. If your
network uses xed IP addresses, set the IP ADDRESS MODE to Static. A
xed or STATIC IP address requires manually entering the IP Address, Subnet
Mask, Gateway, and DNS in the IP ADDRESS CONFIGURATION sub menu.

NETWORK CONFIGURATION

IP ADDRESS MODE
RENEW DHCP IP ADDRESS
VIEW NETWORK SETTINGS
TEST NETWORK CONNECTION
BACK

DHCP

SOFTWARE INFORMATION: Displays the current software installed in the
unit. It shows the MAIN, DSP and STANDBY software versions. There is also
an option to check for software updates. This feature lets the unit search
for software updates on the Internet. The network needs to be properly
congured. Alternatively, you can load the software through the front USB
socket. For more information on the software update process please contact
your authorized Rotel dealer.

RESTORE FACTORY DEFAULT: This option sets the unit back to the original
setting as when it left the factory. All user settings will be erased.

NOTE: Use caution when resetting the RSP-1576 to factory defaults
as all user configured options will be erased and reset to original
factory settings.

Video Setup

VIDEO SETUP

STANDBY VIDEO SOURCE
FAST AUDIO SYNC
OSD FORMAT
BACK

The VIDEO SETUP menu provides configuration of the HDMI outputs. See
the HDMI INPUTS & OUTPUTS section of this manual for details on HDMI
connections.

STANDBY VIDEO SOURCE: Options are “Disable”, “HDMI 1-6”, “HDMI
Front”, or “Last”. This allows the selected HDMI source input to pass-through
the RSP-1576 while in standby mode. Audio and video are passed directly
to the attached TV or display.

NOTE: When the Standby Video Source is enabled the RSP-1576 will
consume additional power when in standby mode.

NOTE: Signal Sense power control is disabled with STANDBY VIDEO
SOURCE is enabled.

FAST AUDIO SYNC: This function allows the HDMI audio to sync more
quickly with the RSP-1576. Only 1 input can be selected for this function.

NOTE: Some source devices do not provide the timing requirements to
allow this function to work properly and could result in static noise before
the audio is heard.

OSD FORMAT: The HDMI On Screen Display output resolution can be
changed from 480p to 576p. The default value is 480p.

Press the BACK button or select “BACK“ on the OSD to exit the VIDEO
SETUP Menu and return to the main menu.

Disable
Disable
480P

27

PEQ Conguration

PEQ CONFIGURATION

SPEAKER : Front Le

FREQUENCY : 20Hz
FREQUENCY : 40Hz Q : 1 GAIN : 0
FREQUENCY : 60Hz Q : 1 GAIN : 0
FREQUENCY : 120Hz Q : 1 GAIN : 0
FREQUENCY : 200Hz Q : 1 GAIN : 0
FREQUENCY : 500Hz Q : 1 GAIN : 0
FREQUENCY : 1200Hz Q : 1 GAIN : 0
FREQUENCY : 4000Hz Q : 1 GAIN : 0
FREQUENCY : 12000Hz Q : 1 GAIN : 0
FREQUENCY : 20000Hz
BACK

The PEQ CONFIGURATION menu allows you to enter EQ values for 10
bands as shown. PEQ setup requires advanced knowledge and equipment
for measuring the frequency response of the room and performance of the
speakers. To properly congure the EQ you should be familiar with the
tools and equipment needed. Typically these settings are only changed
by professional installers to ensure optimal performance of the RSP-1576.

Use the navigation buttons to highlight the frequency: Push the ENTER
button on the remote control to access and make changes. Use the Up/
Down arrow buttons to change the value. Use the Left/Right arrow buttons
to move to the next section on the line. Press ENTER again to conrm settings
and allow navigation to the next PEQ BAND. The Audio Conguration
will determine which speakers are available for conguration in the PEQ
Conguration menu.

FREQUENCY: There are 10 bands available and the frequency can be
changed between 10 - 24kHz as below.

BAND 1 Freq: 10Hz - 40Hz, 1Hz Step Default 20Hz
BAND 2 Freq: 20Hz - 44Hz, 1Hz Step Default 40Hz
BAND 3 Freq: 45Hz - 89Hz, 1Hz Step Default 60Hz
BAND 4 Freq: 90Hz - 180Hz, 10Hz Step Default 120Hz
BAND 5 Freq: 190Hz - 350Hz, 10Hz Step Default 200Hz
BAND 6 Freq: 360Hz - 690Hz, 10Hz Step Default 500Hz
BAND 7 Freq: 700Hz - 1900Hz, 100Hz Step Default 1.2kHz
BAND 8 Freq: 2kHz - 7.78kHz, 100Hz Step Default 4kHz
BAND 9 Freq: 8kHz - 20kHz, 100Hz Step Default 12kHz
BAND 10 Freq: 8kHz - 24kHz, 100Hz Step Default 20kHz

Q: The Q value can be adjusted between 1 to 10.

GAIN: The gain can be set between -12 to +2.

Q : 1

Q : 1

GAIN : 0

GAIN : 0

Troubleshooting

Most difculties in audio systems are the result of incorrect connections, or
improper control settings. If you encounter problems, isolate the problem
area, check the control settings, determine the cause of the fault and make
the necessary changes. If you are unable to get sound from the unit, refer
to the suggestions for the following conditions:

The unit does not turn on

• Make sure the power cord is plugged into the rear panel and a AC outlet.

• Make sure the rear panel POWER switch is in the ON position.

No sound from any input

• Make sure that MUTING is off and VOLUME is turned up.

• Make sure source inputs are connected and configured correctly.

No sound from digital sources

• Make sure that digital input connector is assigned to the proper source
input and that the source input is configured to use the digital input
rather than an analog input.

• Check the configuration of the digital input source player to ensure
that the digital output is activated.

No sound from some speakers

• Check all power amp and speaker connections.

• Check Speaker Configuration settings in the Setup menus.

No Video Output

• Make sure that the TV monitor is connected properly and check the
input assignments.

• Check the source input and TV output resolution are compatible. A 4K
source can only be sent to a 4K monitor.

• HDMI cables must be 5 meters or less in length.

• If watching 3D sources, make sure the display is 3D enabled.

Video and Audio do not match.

• Check that the proper video source is selected for each input.

To exit this menu press the BACK button or select “BACK“ on the OSD then
press the SETUP button to return to normal operations.

NOTE: Q in EQ value relates to the bandwidth of the filter. The higher
the value, the narrower the bandwidth.

• Check that the group delay (lip-sync) setting is not mis-adjusted.

Clicking or popping sounds when switching inputs

• The unit uses relay switching to preserve maximum sound quality. The
mechanical clicking of the relays is normal.

• Switching between HDMI sources may cause delays as HDMI two way
communications “handshake” must be established between the source
and display. The time required for the handshake varies depending
on the attached equipment.

28

RSP-1576 Surround Sound Processor

Controls do not operate

• Make sure that fresh batteries are installed in the remote.

• Make sure that the IR sensor on the front panel is not blocked. Aim the
remote control at the sensor.

• Make sure the sensor is not receiving strong IR light (sunlight, halogen
lighting, etc.).

• Unplug the unit from the AC outlet, wait 30 seconds, and plug it
back to reset.

• Conrm the IR Codeset set in the remote control and RSP-1576 are
matched to either Codeset 1 or Codeset 2.

“Made for iPod,” and “Made for iPhone,” means that an electronic accessory

has been designed to connect specically to iPod or iPhone, respectively, and
has been certied by the developer to meet Apple performance standards. Apple
is not responsible for the operation of this device or its compliance with safety
and regulatory standards. Please note that the use of this accessory with iPod,
or iPhone may affect wireless performance.

iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple
Inc., registered in the U.S. and other countries.

Specications

Audio

Total Harmonic Distortion 0.0006% (Analog Bypass)

0.003% (Digital Input)
Intermodulation Distortion (60 Hz : 7 kHz, 4:1) < 0.005%
Frequency Response
Phono Input 20 Hz - 20k Hz, ± 0.5 dB
Analog Bypass 10 Hz - 100k Hz, ± 1 dB
Digital Input 20 Hz - 20k Hz, ± 0.5 dB
Signal to Noise Ratio (A-weighted)
Analog Bypass 112 dB
Digital Input 112 dB
Input Sensitivity/Impedance
Phono Level 3.5 mV / 47k ohms
Line Level 270 mV / 100k ohms
Balance Level 500 mV / 100k ohms
Preamp Output Level
Line Level 1.0 V
Channel Separation (at 10k Hz) > 75 dB
Digital Audio LPCM (up to 192kHz, 24-bit)
Dolby
Dolby
Dolby
DTS-HD Master Audio,
DTS X

Video

Input Resolutions 480i/576i, 480p/576p, 720p,
1080i, 1080p, 1080p 24Hz,
3D, 4K, UHD, 4K 60Hz, 4K HDR10
Output Resolution 480i/576i, 480p/576p, 720p
1080i, 1080p, 1080p 24Hz,
3D, 4K, UHD, 4K 60Hz, 4K HDR10
Color Space Support sRGB, YCbCr 4:2:2, YCbCr 4:4:4
Deep Color Support 24-bit, 30-bit, 36-bit
HDMI Inputs/Outputs 7 inputs supporting HDCP 2.2, HDMI2.0a
2 outputs supporting HDCP 2.2, HDMI2.0a
Audio Return Channel

General

Power Consumption 60 watts
< 0.5 watt (standby)
Power Requirements (AC) 120 volts, 60Hz
230 volts, 50Hz
BTU 114 BTU/h
Dimension (W x H x D) 431 x 144 x 348 mm
17 x 5
Front Panel Height 3U / 132.6 mm / 5 1/4 in
Weight 8.8 kg / 19.4 lbs

All specifications are accurate at the time of printing.
Rotel reserves the right to make improvements without notice.

Rotel and the Rotel Hifi logo are registered trademarks of The Rotel Co., Ltd. Tokyo, Japan.

®

Surround,

®

TrueHD,

®

ATMOS,

2

/3 x 13 5/7 in

Français

Sommaire

29

Schéma 1 : Commandes et Connexions 5
Schéma 2 : Télécommande 6
Schéma 3 : Amplicateurs et caissons de graves 7
Schéma 4 : Connexions audio numériques et PC-USB 8
Schéma 5 : Connexions à un lecteur Blu-Ray ou Vidéo 8
Schéma 6 : Connexions USB en face avant 9
Schéma 7 : Connexions à un lecteur de CD 9
Schéma 8 : Connexions à un tuner 10
Schéma 9 : Connexions HDMI avant 10
Schéma 10 : Connexions HDMI à l’arrière 11
Afchage des menus sur écran 12

Remarques importantes concernant la sécurité .............................31

A propos de Rotel .................................................32

Mise en route ....................................................32

Caractéristiques Vidéo 32
Caractéristiques Audio 32
Caractéristiques Surround 32
Autres fonctions 32
Déballage 32
Installation 33

Vue générale de la connectique . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Entrées et sorties HDMI .............................................33

Entrées HDMI IN arrières 1-6 r 33
Entrée HDMI IN avant 6 33
Sorties moniteur HDMI e 33

Sorties et entrées audio .............................................34

Entrée PHONO f 34
Entrées TUNER f 34
Entrée CD f 34
Entrée AUX f 34
Entrée BALANCED (Symétrique) d 34
Entrées MULTI g 34
Sorties Préampli h 34
Entrées Numériques w 34
Entrée PC-USB t 34
Entrée USB en face avant 5 35

Autres Connexions ................................................35

Prise secteur j 35
Interrupteur principal de mise sous tension a 35
Connexions 12V TRIGGER i 35
Prise jack REM IN o 35
Prises jack IR OUT p 35
Prises jack IR OUT p 35
Rotel Link [ 35
Prise RS232 y 35
Prise Réseau u 35

CONNEXIONS ....................................................36

Connexion des amplicateurs de puissance 36
Connexion d’un caisson de grave 36
Connexions à un lecteur DVD, Blu-ray, un récepteur câble, satellite,
console de jeux ou tuner HDTV 36
Connexion à un lecteur Blu-ray ou DVD 36
Connection d’un diffuseur vidéo 36
Connexion d’un lecteur de CD ou d’une source XLR 36
Connexion d’un tuner 37
Connexion d’un iPod / iPhone 37

Vue d’ensemble de la façade .........................................37

Ecran en face avant 3 37
Capteur de télécommande 2 37

Vue d’ensemble de la télécommande . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Vue d’ensemble des touches et des commandes ............................38

Touche STANDBY 1 et Touche POWER ON/OFF A 38
Bouton de VOLUME et Touche VOLUME UP/DOWN =D 38
Bouton AFFICHAGE (DISP) 0B 38
Bouton Conguration (Setup) H 38
Touches de Navigation et de Sélection (FONCTION) I 38
Touche MUTE -F 38
Touches INPUT 4qM 38
Touche SUR+ 9B 38
Touches de commandes pour la lecture L 38
Bouton DIM J 38
Boutons SUB, CTR et REAR B 38
Touche MEM E 38
Touche LIGHT N 38
Touche ASSISTIVE LIGHT O 38

Modes surround automatiques ........................................38

Sélection manuelle des modes surround ..................................38

Audio numérique stéréo 39
Stéréo analogique 39

Fonctions de base ..................................................39

Sélection des entrées 39

Fonctionnement USB/iPod ...........................................39

Connexion d’un iPod ou d’un iPhone 5 39
Boutons de lecture L 40

Bluetooth. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Connexion Bluetooth 40

Prise USB arrière ..................................................40

Connexion à la prise USB arrière 40

Réglages et conguration ............................................40

Menus de base ....................................................40

Touches de navigation 40
Menu Principal (Main Menu) 40

Conguration des Entrées ............................................40

Conguration des Entrées (Input Setup) 41
Conguration de l’entrée Multi 42

Conguration de la partie audio .......................................42

Conguration audio 42

Conguration des Enceintes et de la partie Audio ...........................42

Conguration des enceintes 43
Conguration Avancée des Enceintes 44
Conguration du caisson de graves 44
Réglage des niveaux des enceintes 45
Réglage des distances des enceintes 46

Réglages Divers ...................................................46

Conguration Système (System Setup) 46
Conguration Vidéo 47
Egalisation PEQ 48

Résolution des pannes ..............................................48

Spécications .....................................................49

30

L’éclair dans un triangle équilatéral indique
la présence interne de tensions électriques
élevées susceptibles de présenter des
risques graves d’électrocution.

Le point d’exclamation dans un triangle
équilatéral indique à l’utilisateur la
présence de conseils et d’informations
importantes dans le manuel d’utilisation
accompagnant l’appareil. Leur lecture est
impérative.

RSP-1576 Processeur Surround

RSP-1576

STANDBYSTANDBY

5V 2.1A

HDMI

MUTE2CH SUR + DISPLAYBYPASS

VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7

USB PC-USB XLR TUNER CD PHONO BT

Tous les appareils Rotel sont conçus en totale conformité
avec les directives internationales concernant les
restrictions d’utilisation de substances dangereuses
(RoHS) pour l’environnement, dans les équipements
électriques et électroniques, ainsi que pour le recyclage
des matériaux utilisés (WEEE, pour Waste Electrical
and Electronic Equipment). Le symbole du conteneur
à ordures barré par une croix indique la compatibilité
avec ces directives, et le fait que les appareils peuvent
être correctement recyclés ou traités dans le respect
total de ces normes.

Assignation des connecteurs
Audio Symétrique (prise XLR 3 broches) :

2

1

3

Pin 1 : Masse/Terre
Pin 2 : Phase/+ve /Point chaud
Pin 3 : Hors Phase /-ve / Point froid

DAB