140G-G-F____, 140G-H-F____, 140G-I-F____, 140G-J-F____, 140G-K-F____
Installation instruction for Flex Cable Operator for 140G-G through K
Istruzioni di installazione
Installationsanleitung
Instructions pour l’installation
Instrucciones de instalación
Installation - Installazione - Instalación
Instalação - -
WARNING:
installing or servicing. Install in suitable enclosure. Keep free from contaminants.
(Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o
manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
(Seguire i requisiti NFPA70E).
WARNUNG:
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem
passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen
Sie die Anforderungen nach NFPA70E).
AVERTISSEMENT:
secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée.
Protéger le produit contre les environnements agressifs. (Vous devez respecter la
norme NFPA70E).
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o
del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E).
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a
instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de
contaminantes. (Cumpra as exigências da norma NFPA70E).
To prevent electrical shock, disconnect from power source before
Vor Installations- oder Servicearbeiten Stromversorgung zur
Avant le montage et la mise en service, couper l'alimentation
Bul. 140G/140MG
CLACK
M4 x .7 x 12 mm
PN-227250
DIR 10000873178 (Version 02)
1/4-20 x .71 in #6-32 x .312 in
R > 6.0” (150 mm)
U >0V
e
> 1.0” (25 mm)
1-3/32"
(32 mm)
(12.7 mm)
(6.35 mm)
Square corners or
up to 1/4" (6.35 mm) radius
Right Hand Flange Left Hand Flange
1/2"
1/4"
1-1/4" Min.
(32 mm)
5/16"
(7.9 mm)
3-1/2"
(89 mm)
(2) .265" (7 mm) Dia. Holes
1-1/4" Min.
(32 mm)
1" Min.
(25.4 mm Min.)
4-11/16"
(119 mm)
1-3/32"
(32 mm)
15" Min.
(381 mm)
PN-227250
DIR 10000873178 (Version 02)
(2)
1
140G-G
140G-I
1
10 - 15 in lbs
1.2 - 1.7 Nm
140G-H
140G-J
140G-K
GI
0.984 in
(25.0 mm)
4.213 in
(107.0 mm)
M4
1.378 in
(35.0 mm)
4.803 in
(122.0 mm)
M4
10 - 15 in lbs
1.2 - 1.7 Nm
PN-227250
DIR 10000873178 (Version 02)
(3)
1
HK
1.181 in
(30.0 mm)
4.370 in
(111.0 mm)
M4
J
5.472 in
(139.0 mm)
1.378 in
(35.0 mm)
M4
1.831 in
(46.5 mm)
6.929 in
(176.0 mm)
M5
2
10 - 15 in lbs
1.2 - 1.7 Nm
T-20
3
PN-227250
DIR 10000873178 (Version 02)
(4)
4
2
1
3
23 - 37 in lbs
2.6 - 4.2 Nm
7/16"
(11 mm)
5
1
10 - 15 in lbs
1.2 - 1.7 Nm
#1
2
PN-227250
DIR 10000873178 (Version 02)
(5)
6
Trip Breaker
CLACK
DC
7
Reset Breaker
A
PN-227250
DIR 10000873178 (Version 02)
8
(6)
8
Breaker On
CLACK
B
9
Breaker Off
CLACK
A
Done
PN-227250
DIR 10000873178 (Version 02)
(7)
A
B
C
3/4"
(19 mm)
D
3/4"
(19 mm)
Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication 140G-IN128C-MU-P - June 2014
Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. Printed in USA.
DIR 10000873178 (Version 02)
PN-227250
Loading...