Radio Shack ET 3229 User Manual

ET 3229 Big Button Speakerphone

OWNER’S MANUAL — Please read before using this equipment.

Your RadioShack Big Button Speakerphone
lets you store up to 13 frequently called tele­phone numbers in memory for quick, easy di­aling of any stored number. Its features
include:

Big Button Keypad

recognition.

Built-in Speakerphone

free operation.

13 Memory Locations

dialing of frequently called numbers.

Ring Indicator

coming call even if the ringer is turned off.

Adjustable Ringer and Receiver Volume

— lets you adjust the ringer and receiver’s
volume to the desired level.

Your telephone is ETL listed to UL standards
and meets all applicable FCC requirements.

— provides easy button

— gives you hands-

— allows quick, easy

— a lighted bar signals an in-

FCC STATEMENT

We have designed your telephone to con­form to federal regulations, and you can con­nect it to most telephone lines. However,
each device that you connect to the tele­phone line draws power from the line. We re­fer to this power draw as the phone’s ringer
equivalence number (REN). The REN is on
the bottom of your phone.

If you use more than one phone or other de­vice on the line, add up all the RENs. If the
total is more than five (three in rural areas),
your phone might not ring. If the ringer oper­ation is impaired, remove one of the devices
from the line.

In the unlikely event your phone causes
problems on the phone line, the telephone
company can disconnect your service. The
phone company tries to notify you in ad­vance. If advance notice is not practical, the
telephone company notifies you as soon as
possible and advises you of your right to file
a complaint with FCC.

Your telephone complies with Part 68 of

, you must, upon request, provide the

Rules

FCC registration numbers and the REN to
your telephone company. Both numbers are
shown on the bottom of the telephone.

This device complies with Part 15 of the

. Operation is subject to the following

Rules

two conditions: (1) this device may not cause
harmful interference, and (2) this device
must accept any interference received, in­cluding interference that may cause undes­ired operation.

You must not connect your telephone

Note:

to:

• Coin-operated systems

• Party-line systems

• Most electronic key telephone systems

FCC

FCC

Lightning

Your telephone has built-in protection circuits
to reduce the risk of damage from surges in
(telephone and power) line current. These
protection circuits meet or exceed the FCC
requirements. However, lightning striking the
telephone or power lines can damage your
telephone.

2001 RadioShack Corporation. All Rights Reserved.

©

RadioShack and RadioShack.com are trademarks

used by RadioShack Corporation.

Lightning damage is not common. Neverthe­less, if you live in an area that has frequent
electrical storms, we suggest you unplug your
telephone when storms approach to reduce
the possibility of damage.

WARNING:

shock hazard, do not expose this product to rain
or moisture.

To reduce the risk of fire or

have the telephone company update the wir­ing for you. You must use compatible modular
jacks that are compliant with Part 68 of

.

Rules

The USOC number of the jack to be in-

Note:

FCC

stalled is RJ11C (or RJ11W for a wall plate
jack).

Mounting the Phone

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION:

ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE­ABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.

!

TO REDUCE THE RISK OF

This symbol is intended to alert
you to the presence of uninsu­lated dangerous voltage within
the product’s enclosure that might
be of sufficient magnitude to con­stitute a risk of electric shock. Do
not open the product’s case.

This symbol is intended to inform
you that important operating and
maintenance instructions are
included in the literature accom­panying this product.

!

PREPARATION

Selecting a Location

Select a location for your telephone that is:

• Near a telephone jack

• Not in the way of normal activities in the
area

Your telephone connects directly to a modular
telephone line jack. If your telephone wiring
does not have a modular jack, you can update
the wiring yourself using jacks and adapters
(available at your local RadioShack store), or

You can mount your telephone on a wall plate,
directly on a wall, or place it on a shelf, desk
or table.

On a Desktop

Use the supplied mounting bracket as a stand
when you place the phone on a desk, shelf, or
table.

1. Insert the mounting bracket’s two smaller
tabs into the matching slots near the key­hole slot on the underside of the phone’s
base. Then press down on the bracket
until its larger tabs snap into place.

2. Plug one end of the supplied long modu­lar cord into the

jack at the back of

LINE

the base.

3. Plug the cord’s other end into a modular
phone line jack.

On a Wall Plate or Wall

1. Insert the mounting bracket’s two smaller
tabs into the matching slots opposite the
keyhole slot on the underside of the
phone’s base. Then press down on the
bracket until its two larger tabs snap into
place.

2. Plug one end of the supplied short modu­lar cord into the

jack at the back of

LINE

the base. Route the modular cord through
the strain relief channel.

3. Plug the cord’s other end into the wall
plate jack, then align the base’s keyhole

2

slots with the wall plate studs and slide
the phone downward to secure it.

meet these specifications could damage
the telephone or the adapter.

4. Press and lift up the handset holder,
rotate it 180°, then snap it back so it holds
the handset.

To mount the phone directly on a wall, in addi­tion to the preceding steps, you need two
screws (not supplied) with heads that fit into
the keyhole slots on the bottom of the base.

15

Drill two holes 3
Then thread a screw into each hole, letting the
heads extend about
the wall.

Substitute the long modular cord for the short
cord mentioned in step 2.

/16 inches (100 mm) apart.

5

/16 inches (8mm) from

Connecting the Handset

Plug one end of the coiled cord into the modu­lar jack on the handset. Then connect it to the
jack on the left side of the telephone base.

Your local RadioShack store sells a va-

Note:

riety of longer coiled handset cords, which are
especially useful when you mount the phone
on a wall.

• Always connect the AC adapter to the
telephone before you connect it to AC
power. When you finish, disconnect the
adapter from AC power before you dis­connect it from the telephone.

Plug the barrel plug of the supplied adapter
into the
phone. Plug the other end into a nearby AC
outlet.

jack at the back of the tele-

DC 9V

Setting the Ringer

If you do not want to hear the phone ring, set

to

RINGER

the ringer off, and you can answer calls if you
hear another phone on the same phone line
ring. The bar-shaped ring indicator flashes
when the phone rings, even when the ringer is
off. If you want to hear the phone ring, set

RINGER

. You can still make calls with

OFF

to HI or LO.

Setting the Dialing Mode

Set

(TONE/PULSE) for the type of service

T/P

you have. If you are not sure which type you
have, do this simple test.

Connecting an AC Adapter

Your telephone operates from telephone line
power. In some areas, however, the tele­phone might not provide enough power to op­erate all of your telephone’s features. If the
volume of the speaker is too low, even with
the volume control set to its highest level, or if
the speaker does not work, you need to con­nect the supplied AC adapter.

Cautions:

You must use a Class 2 power
source that supplies 9V DC and

!

delivers at least 200 mA. Its
center tip must be set to positive and its
plug must fit the telephone's
The supplied adapter meets these speci­fications. Using an adapter that does not

DC 9V

jack.

1. Set

2. Press any number except 0. If your phone

3

to T. Lift the handset and listen for

T/P

a dial tone.

requires that you dial an access code (9,
for example) before you dial an outside
number, do not press the access code
number either.

If the dial tone stops

tone service. Leave the setting to T.

If the dial tone continues

service. Set

T/P

, you have touch-

, you have pulse

to P.

OPERATION

Using the Speakerphone

You can use the built-in speakerphone in­stead of the handset. When you press

ERPHONE

, the indicator lights and the phone
connects the telephone line. To disconnect
the telephone line, press

SPEAKERPHONE

again. The indicator goes off.
If you are using the handset and you want to

switch to the speakerphone, press

. Return the handset to the cradle.

PHONE

To switch from the speakerphone to the hand­set, lift the handset. When you lift up the
handset, the speakerphone turns off automati­cally.

If you decide to change from speakerphone to
handset operation during redial or memory di­aling, let the number completely dial before
you lift the handset.

Setting the Receiver and Speaker­phone Volume

Slide

RECEIVER VOL

to adjust the handset receiver volume.
Slide

SPEAKER VOL

volume as desired.

to

LO/MED/HI

to set the speakerphone

Using Mute

To temporarily disconnect the speakerphone
or handset without ending the call, so you can
talk privately with someone in the room, press

The MUTE indicator lights. To resume

MUTE.

your call, press
goes off.

. The MUTE indicator

MUTE

SPEAK-

SPEAKER-

as desired

2. Enter the telephone number, then press
again.

STORE

3. Press the direct memory location (

1-3

) at
the top of the phone or the desired stan­dard memory location (

) using the

0-9

standard keypad.

Notes:

• Since pressing

does not break the

STORE

dial tone, the phone company “line alert”
signal may occur when entering longer
numbers. This does not affect number
storage.

• To replace a number in one of the mem­ory locations repeat steps 1 through 3.
During step 2, enter the new number in
any memory location you wish to change.

Dialing a Stored Number

To dial a number stored in direct memory,
press the desired direct memory location (

1-3

at the top of the phone.
To dial a number stored in a standard memory

location, press
memory key (

0-9

MEMORY

).

, then the desired

Chain-Dialing Memory Numbers

If you frequently use special telephone servic­es, you can save time by storing the phone
number of the service in one memory location
and the rest of the information, such as a long
distance number, in another memory location.

To chain-dial, enter the memory location of
the service number first. Then when the ser­vice answers, enter the memory location of
the other information.

)

Storing a Number in Memory

The telephone has 3 direct and 10 standard
phone memory storage locations.

1. With the handset off hook or
on, press

PHONE

STORE

SPEAKER-

.

We recommend you do not store secu-

Note:

rity numbers, such as personal access codes
for bank-by-phone services, in any memory
location.

4

Using Redial

You can quickly dial the last number dialed by
pressing

REDIAL/PAUSE

tone. The redial number is replaced each time
you dial a new number. The redial memory
holds up to 32 digits, to store long distance as
well as local numbers.

when you hear a dial

Note:

If you press

while dialing a num-

FLASH

ber, only the digits after FLASH are stored in
redial memory.

Using Flash

Many special telephone services, such as Call
Waiting, require a switchhook signal. The

button provides the electronic equiva-

FLASH

lent of a switchhook operation.
For example, if you have Call Waiting, you

can put a call on hold and take a secon d in­coming call on the same line by pressing

.

FLASH

Only the digits you dial after you press

FLASH

are stored in redial memory.

If you do not have any special phone

Note:

services, pressing

might disconnect

FLASH

the current call.

Using Pause

In some telephone systems, you must dial an
access code (9, for example) and wait for a
second dial tone before dialing an outside
number. When you manually dial a number, or
when you store a number in memory, you can
have your telephone pause anywhere during
the dialing sequence. Simply press

at the desired location.

PAUSE

REDIAL/

When you redial or memory dial a number, the
telephone pauses for about 3 to 6 seconds at
the pause entry. For longer pauses, press

DIAL/PAUSE

again.

RE-

5

TROUBLESHOOTING

If your telephone is not operating properly, go
through this checklist.

Is the phone properly connected?
Is the
If the telephone’s volume level drops or it be-

gins to make strange sounds, determine if
other phones have been picked up on the
same line. This phone might not operate when
other phones are active on the same line (es­pecially in areas with low telephone voltage).
Hang up the other phones to correct the prob­lem.

If any additional telephone devices have been
added at or about the time this phone’s perfor­mance diminished, recalculate the total REN
for your devices (see “FCC STATEMENT” on
Page 1).

If the volume of the speaker is too low, even
with the volume control set to its highest level,
or if the speaker does not work, connect the
supplied AC adapter (see “Connecting an AC
Adapter” on Page 3).

switch set correctly?

T/P

Modifying or tampering with the telephone’s
internal components can cause a malfunction
and might invalidate its warranty and void
your FCC authorization to operate it. If your
telephone is not performing as it should, take
it to your local RadioShack store for assis­tance. If the trouble is affecting the telephone
lines, the phone company can ask you to dis­connect your telephone until you have re­solved the problem.

When the party on the phone cannot hear
you, but you can hear them, check the MUTE
indicator. If the light is on, press
off.

If you still have problems, disconnect the
phone. If other phones on the same line work
properly, the fault is in this phone or its instal­lation. If you cannot find the problem, take
your phone to your local RadioShack store for
assistance.

MUTE

so it is

CARE

Keep the telephone dry; if it gets wet, wipe it
dry immediately. Use and store the telephone
only in normal temperature environments.
Handle the telephone carefully; do not drop it.
Keep the telephone away from dust and dirt,
and wipe it with a damp cloth occasionally to
keep it looking new.

6

A QUICK LOOK AT YOUR PHONE

-

DIRECT MEMORY (see “Storing a Number in
Memory” and “Dialing a Stored Number” on
Page 4).

RING INDICATOR BAR

STORE (see “Storing a
Number in Memory” on
Page 4).

FLASH (see “Using Flash”
on Page 5).

SPEAKERPHONE (see “Using the Speak­erphone” on Page 4).

RECEIVER volume control for adjusting the
volume of the handset receiver (see “OPERA­TION” on Page 4).

MEMORY (see “Dialing a
Stored Number” on
Page 4).

MUTE (see “Using
Mute” on Page 4).

REDIAL/PAUSE (see
“Using Redial” on
Page 5 and “Using
Pause” on Page 5).

DC 9V jack for connecting an optional AC adapter
(see “Connecting an AC Adapter” on Page 3).

Control for adjusting the SPEAK­ERPHONE volume.

RINGER switch for adjusting ringer volume (see “Set
ting the Ringer” on Page 3).

LINE jack

T/P switch for setting the Dialing Mode (see
“Setting the Dialing Mode” on Page 3).

7

Limited One-Year Warranty

This product is warranted by RadioShack against manufacturing defects in material and workman­ship under normal use for one (1) year from the date of purchase from Radi oSha ck company- owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra­dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE­SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT T O ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR­MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN­CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN­TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limit a­tion of incidental or consequential damages, so the above limitations or exclusions may not apply to
you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un­less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop­erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallat i on.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.

RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102

We Service What We Sell

12/99

RadioShack Corporation
Fort Worth, Texas 76102

43-3229

06A01

Printed in China