Q-See QSZ515D User Manual

Processor

Frequency(H)

System

Medium Speed Intelligent Dome PTZ

QSZ515D

QSZ515DQSZ515D

User’s Manual

Part 1 Performance Features

◇

4.2”Vandalproof Pan/Tilt Dome Camera

◇

1/3” SONY CCD + SONY DSP

◇

540TVL

◇

Super wide voltage board: 8-18V

◇

High transparent vandal-proof dome cover

◇

5-15mm F2.2 2.0MP auto focus lens

◇

With RS485 remote control, With 128 preset points

◇

360° Horizontal endless rotation, 90° vertical movement

◇

A panoramic view

◇

body rotates flexibly with less noise and

wider view shooting

◇

Memory function at accidental power-off (Settings saved)

Technical Specifications:

Model

Image Sensor 1/3"SONY CCD

PDS-320FZA

Rev 120110

Digital Signal

Signal System PAL / NTSC

Scanning System 2:1 Interlace

Scanning

Sync. System Internal

Horizontal

Effective Pixels

(HxV)

Shuttle Speed

Mini Illumination 0.01 Lux

S/N Ratio

Gamma

SONY DSP

NTSC:15.734KHZ , PAL:15.625KHZ

540TVL

PAL:795×596

NTSC:811×508

PAL=1/50 ~1/100,000 sec；NTSC=1/60 ~1/100,000

sec

> 48dB（Auto Gain Off

0.45

）

Lens

Temperature

White Balance Auto

BLC

Video Output

AGC

Power Voltage Super Wide Voltage (8V~18V)

Input Current DC12V+/_20% 50/60Hz, 1.2A above

Output Current 12V 800mA

Operating

1.3 Megapixel 5-15mm F2.2 2.0MP auto focus lens

Open

1.0V P-P,75Ω BNC

Auto

14°F to 122°F (-10°C to 50℃)

（

relative humidity: up to 95%

）

Built-in Decoder

Full digital design, all data saved inside of the module with memory

function in case of accidental power loss.

All in one integrated design, high reliability

128 preset positions can be saved

1-80 preset positions support auto cruise function, while 1 cruise route

can save 8 preset positions, each position pauses 6 seconds.

Uses RS485 remote control interface

Thanks to its expanding function, any keyboard can operate the controls

of this high speed dome.

Part 2 Functions & Operating Instructions

Storage Temp -22°F to 158°F (-30°C to 70°C)

Color

Dimensions(LXD)

Weight

Address Range 1-256

Module Index of Variable Speed Pan/Tilt/Zoom:

1. Horizontal scanning: 360°rotation

2. Horizontal speed: 0.5°—50°/s

3. The lowest speed at 0.5°/s, no vibrating images

3. Vertical scanning: >90°

4. Vertical speed: 0.5°—30°/s

5. 128 preset positions (PTZ and vari-focal lens included)

6. Speed of preset positions: 50°/s

7. PTZ scanning precision: ±0.5°

8. 3X zoom

Control Protocol:

PELCO“P”Protocol

PELCO“D”Protocol

Baud Rate

White

5x5 in (125×125mm)

2.2 lbs (1KG)（without bracket and adapter）

: 1200b/2400b/4800b/9600b

This part mainly describes the leading functions and common

principles of the all in one intelligent dome camera. It does not refer to t

he specific operating methods. Different systematical

platforms have different methods. In some cases, special

requirements and operating methods would exist, subject to the

product manual.

1. Set CCTV encoding

The control board of the dome has a 10-DIP-switch, used to set

address, communication and control protocols PELCO-D/P (refer to “DIP switch

set”). Any command should agree with the targeted

address, and cameras only response when address code is the same.

2. CCTV Camera Operation

Zoom control

User can adjust the image farther/nearer to get a panoramic view by contr

olling the keyboard buttons

oth digital and optical vari-focus. Digital vari-focus can be set.

In the following cases, the camera’s target is unable to auto

Focus:

The target is not in the center of the image;

When watching the farther or nearer objects, the objects are not clear;

The target is a strong light, like neon light, spot light etc;

The object moves to fast;

ZOOM- / ZOOM+

. The speed dome supports b

Large square of monotonous object, like a wall;

The object is too dark or vague;

The targeted picture is too small

3. Surveillance function

Set & Transfer the preset points

The function of preset positions is, temporarily storing such

location parameters as horizontal angle / inclination / lens’ focus in a mem

ory and transferring them whenever they’re needed. User

can quickly transfer the preset positions via the keyboard, remote or some

thing else such as PC software. The speed dome

supports 127 preset points.

Automatic Cruise

Automatic Cruise is an internal set function, which inserts the

points and sets up the automatic cruise among preset positions by program

ming them beforehand in the cruise lists. The cruise order and pausing timi

ng can be programmed and one cruise route can store 8 points and time

Auto Scanning

Cameras can level scan back and forth among the left & right limits at

the set speed via the keyboard and menu settings using the left and righ

t limits setup beforehand.

Power-off Protection

When a planned or unplanned power-off happens, the camera

will automatically preserve the movement state before the

power-off. When the power returns, the camera will auto-recover the previ

ous stored movement.

Part 3 Extended Function

This section describes the extended function and common principles of the a

ll in one intelligent dome camera. Different systematical

platforms have different methods. In some cases, special

requirements & operational methods could exist, subject to

systematical manufacturer’s manual.

1. Set the scanning

The speed dome can be set in two fixed locations and scan back and fort

h at the set speed. Set #126 for linear scanning. Set #xxx preset position,

xxx is the scanning speed (1-50 adjustable), after that, move the rod, the

image would move to the beginning locations. Set #127 as scanning

beginning location, moves the image to the ending location and set #1

28 as the ending scan location.

Example 1

Setting Method：

Example 2：Scan setting at the speed of 50s around.

Setting Method：

Transfer the cruise group

Transfer #101-102 preset point; relatively start #1-2 cruise groups. For ex

ample：Start #1 cruise group.

Method: Transfer #101 preset position.

Start the linear scanning

Transfer #128 preset position.

Start auto-scanning

Transfer #125 preset position or press auto-start button.

360° Auto-scanning back and forth. The speed is fixed internally.

1. Clearing of fault

：

Scan setting at the speed of 1s around.

Set #126 preset position.

Set #30 as speed index.

Move the rod and adjust the image as the scanning one.

Set #127 as the beginning location.

Move the rod and adjust the image to the scanning ending location.

Set #128 as the ending location

Set #126 preset position.

Set #50 as speed index.

Move the rod and adjust the image as the scanning one.

10.

Set #127 as the beginning location.

11.

Move the rod

12.

Set #128 as the ending location

Part 4 Appendix

+ 4 hidden pages