Pioneer VSX-60 User Manual

Operating Instructions
AV Receiver
VSX-60
IMPORTANT
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
WARNING
This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filled with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture.
WARNING
Before plugging in for the first time, read the following section carefully.
The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e.g., 230 V or 120 V) written on the rear panel.
WARNING
To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment.
VENTILATION CAUTION
When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 40 cm at top, 10 cm at rear, and 20 cm at each side).
WARNING
Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
D3-4-2-1-3_A1_En
D3-4-2-1-4*_A1_En
D3-4-2-1-7a_A1_En
D3-4-2-1-7b*_A1_En
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
D3-4-2-1-1_A1_En
Operating Environment
Operating environment temperature and humidity: +5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light)
If the AC plug of this unit does not match the AC outlet you want to use, the plug must be removed and appropriate one fitted. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. If connected to an AC outlet, the cut-off plug can cause severe electrical shock. Make sure it is properly disposed of after removal. The equipment should be disconnected by removing the mains plug from the wall socket when left unused for a long period of time (for example, when on vacation).
CAUTION
The STANDBY/ON switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).
D3-4-2-1-7c*_A1_En
D3-4-2-2-1a_A1_En
D3-4-2-2-2a*_A1_En
11)
Read these instructions.
1)
Keep these instructions.
2)
Heed all warnings.
3)
Follow all instructions.
4)
Do not use this apparatus near water.
5)
Clean only with dry cloth.
6)
Do not block any ventilation openings. Install in
7)
Only use attachments/accessories specified by the manufacturer.
12)
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to
avoid injury from tip-over. accordance with the manufacturer’s instructions. Do not install near any heat sources such as
8) radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized
9) or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or
10) pinched particularly at plugs, convenience
13)
Unplug this apparatus during lightning storms or when unused for long periods of time.
14)
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
receptacles, and the point where they exit from the apparatus.
D3-7-13-69_En
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help.
Caution
To prevent fire hazard, the Class 2 Wiring Cable should be used for connection with speaker, and should be routed away from hazards to avoid damage to the insulation of the cable.
D3-7-13-67*_A1_En
WARNING: Handling the cord on this product or
cords associated with accessories sold with the product may expose you to chemicals listed on proposition 65 known to the State of California and other governmental entities to cause cancer and birth defect or other reproductive harm.
Information to User
D8-10-1-2_A1_En
D36-P5_B1_En
Alterations or modifications carried out without appropriate authorization may invalidate the user’s right to operate the equipment.
D8-10-2_A1_En
2
IMPORTANT NOTICE
THE MODEL NUMBER AND SERIAL NUMBER OF THIS EQUIPMENT ARE ON THE REAR OR BOTTOM. RECORD THESE NUMBERS ON YOUR ENCLOSED WARRANTY CARD AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.
D36-AP9-1_A1_En
CAUTION
This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables and connectors for connections.
D8-10-3a_A1_En
This product is for general household purposes. Any failure due to use for other than household purposes (such as long-term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the warranty period.
K041_A1_En
This Class B digital apparatus complies with Canadian ICES-003.
D8-10-1-3_A1_En
CAUTION: HOT SURFACE. DO NOT TOUCH.
The top surface over the internal heatsink may become hot when operating this product continuously.
The Safety of Your Ears is in Your Hands
Get the most out of your equipment by playing it at a safe level – a level that lets the sound come through clearly without annoying blaring or distortion and, most importantly, without affecting your sensitive hearing. Sound can be deceiving. Over time, your hearing “comfort level” adapts to higher volumes of sound, so what sounds “normal” can actually be loud and harmful to your hearing. Guard against this by setting your equipment at a safe level BEFORE your hearing adapts.
ESTABLISH A SAFE LEVEL:
Set your volume control at a low setting.
Slowly increase the sound until you can hear it
comfortably and clearly, without distortion.
Once you have established a comfortable sound level, set the dial and leave it there.
BE SURE TO OBSERVE THE FOLLOWING GUIDELINES:
Do not turn up the volume so high that you can’t hear what’s around you.
Use caution or temporarily discontinue use in potentially hazardous situations.
Do not use headphones while operating a motorized vehicle; the use of headphones may create a traffic hazard and is illegal in many areas.
S001a_A1_En
3
Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly.
Contents
01 Before you start
Checking what’s in the box ................................................................................................................................................ 8
Installing the receiver ......................................................................................................................................................... 8
Loading the batteries .......................................................................................................................................................... 8
Operating range of remote control unit............................................................................................................................8
About using AVNavigator (included CD-ROM)................................................................................................................9
05 Basic playback
Playing a source ...............................................................................................................................................................39
Playing an iPod .................................................................................................................................................................40
Playing a USB device .......................................................................................................................................................41
Listening to the radio ........................................................................................................................................................42
Bluetooth ADAPTER for Wireless Enjoyment of Music ................................................................................................43
06 Listening to your system
Enjoying various types of playback using the listening modes ....................................................................................46
Selecting MCACC presets ...............................................................................................................................................47
Choosing the input signal ................................................................................................................................................47
Better sound using Phase Control ..................................................................................................................................48
02 Controls and displays
Remote control .................................................................................................................................................................11
Display ...............................................................................................................................................................................13
Front panel ........................................................................................................................................................................14
03 Connecting your equipment
Connecting your equipment ............................................................................................................................................16
Rear panel .........................................................................................................................................................................16
Determining the speakers’ application ..........................................................................................................................17
Placing the speakers ........................................................................................................................................................18
Connecting the speakers .................................................................................................................................................19
Installing your speaker system ........................................................................................................................................19
Selecting the Speaker system .........................................................................................................................................21
About the audio connection ............................................................................................................................................21
About the video converter ................................................................................................................................................22
About HDMI ......................................................................................................................................................................22
Connecting your TV and playback components ............................................................................................................23
Connecting an HDD/DVD recorder, BD recorder and other video sources ...............................................................25
Connecting a satellite/cable receiver or other set-top box ...........................................................................................26
Connecting other audio components .............................................................................................................................27
Connecting AM/FM antennas .........................................................................................................................................28
MULTI-ZONE setup ...........................................................................................................................................................29
Connecting to the network through LAN interface .......................................................................................................30
Connecting optional Bluetooth ADAPTER .....................................................................................................................30
Connecting an iPod ..........................................................................................................................................................31
Connecting a USB device ................................................................................................................................................31
Connecting an HDMI-equipped component to the front panel input .........................................................................31
Connecting to a wireless LAN .........................................................................................................................................31
Connecting an IR receiver ...............................................................................................................................................32
Switching components on and off using the 12 volt trigger .........................................................................................32
Plugging in the receiver ...................................................................................................................................................32
04 Basic Setup
Changing the OSD display language (OSD Language) ................................................................................................34
Automatically conducting optimum sound tuning (Full Auto MCACC) .....................................................................34
The Input Setup menu ......................................................................................................................................................36
Operation Mode Setup .....................................................................................................................................................37
About the Home Menu.....................................................................................................................................................37
07 Playback with NETWORK features
Introduction ....................................................................................................................................................................... 50
Playback with Network functions....................................................................................................................................51
About network playback...................................................................................................................................................52
About playable file formats ..............................................................................................................................................54
08 Control with HDMI function
About the Control with HDMI function ...........................................................................................................................56
Making Control with HDMI connections ........................................................................................................................56
HDMI Setup.......................................................................................................................................................................56
Before using synchronization ..........................................................................................................................................56
About synchronized operations ......................................................................................................................................57
Setting the PQLS function ...............................................................................................................................................57
About Auto Sound Retriever Link and Stream Smoother Link .....................................................................................57
Cautions on the Control with HDMI function ................................................................................................................57
09 Using other functions
Setting the Audio options ................................................................................................................................................59
Setting the Video options .................................................................................................................................................61
Switching the speaker terminals ....................................................................................................................................63
Using the MULTI-ZONE controls .....................................................................................................................................63
Making an audio or a video recording ............................................................................................................................64
Using the sleep timer .......................................................................................................................................................64
Dimming the display ........................................................................................................................................................64
Checking your system settings .......................................................................................................................................64
Resetting the system ........................................................................................................................................................64
10 Controlling the rest of your system
About the Remote Setup menu.......................................................................................................................................67
Operating multiple receivers ...........................................................................................................................................67
Setting the remote to control other components ..........................................................................................................67
Selecting preset codes directly .......................................................................................................................................67
Programming signals from other remote controls .......................................................................................................68
Erasing one of the remote control button settings ........................................................................................................68
Erasing all learnt settings that are in one input function .............................................................................................69
Direct function ..................................................................................................................................................................69
About the ALL ZONE STBY (All Zone Standby) and DISCRETE ON (Discrete On) functions ....................................69
Resetting the remote control settings ............................................................................................................................69
Controlling components ..................................................................................................................................................70
4
11 The Advanced MCACC menu
Making receiver settings from the Advanced MCACC menu ......................................................................................73
Automatic MCACC (Expert) .............................................................................................................................................73
Manual MCACC setup .....................................................................................................................................................75
Checking MCACC Data ....................................................................................................................................................77
Data Management............................................................................................................................................................78
12 The System Setup and Other Setup menus
Making receiver settings from the System Setup menu...............................................................................................81
Manual speaker setup ......................................................................................................................................................81
Network Setup menu .......................................................................................................................................................83
Checking the Network Information .................................................................................................................................84
The Other Setup menu .....................................................................................................................................................84
13 FAQ
Troubleshooting ................................................................................................................................................................88
Power .................................................................................................................................................................................88
No sound ...........................................................................................................................................................................88
Other audio problems ......................................................................................................................................................89
ADAPTER PORT terminal ................................................................................................................................................90
Video ..................................................................................................................................................................................90
Settings ..............................................................................................................................................................................90
Professional Calibration EQ graphical output ...............................................................................................................91
Display ...............................................................................................................................................................................91
Remote control .................................................................................................................................................................91
HDMI ..................................................................................................................................................................................91
AVNavigator ......................................................................................................................................................................92
USB interface ....................................................................................................................................................................93
iPod ....................................................................................................................................................................................93
Network .............................................................................................................................................................................93
Wireless LAN .....................................................................................................................................................................94
14 Additional information
Surround sound formats .................................................................................................................................................97
About iPod .........................................................................................................................................................................97
About SiriusXM .................................................................................................................................................................97
About FLAC .......................................................................................................................................................................97
Auto Surround, ALC and Stream Direct with different input signal formats ..............................................................98
Speaker Setting Guide......................................................................................................................................................98
About messages displayed when using network functions .........................................................................................99
Important information regarding the HDMI connection ............................................................................................100
Cleaning the unit ............................................................................................................................................................100
Glossary ...........................................................................................................................................................................101
Features index .................................................................................................................................................................104
Specifications .................................................................................................................................................................105
Preset code list................................................................................................................................................................106
5
Flow of settings on the receiver
Flow for connecting and setting the receiver
The unit is a full-fledged AV receiver equipped with an abundance of functions and terminals. It can be used eas­ily after following the procedure below to make the connections and settings.
Required setting item: 1, 2, 3, 4, 5, 7, 9 Setting to be made as necessary: 6, 8, 10, 11, 12
Important
The receiver’s initial settings can be made on the computer using Wiring Navi on the AVNavigator CD-ROM included with the receiver. In this case, virtually the same connections and settings as in steps 2, 3, 4, 5, 6, 7 and 8 can be made interactively. For instructions on using AVNavigator, see About using AVNavigator (included
CD-ROM) on page 9.
1 Before you start
! Checking what’s in the box on page 8 ! Loading the batteries on page 8
j
2 Determining the speakers’ application (page 17)
! 7.2 channel surround system (Front height) ! 7.2 channel surround system (Front wide) ! 7.2 channel surround system & Speaker B connection ! 5.2 channel surround system & Front Bi-amping connection (High quality surround) ! 5.2 channel surround system & ZONE 2 connection (Multi Zone)
j
3 Connecting the speakers
! Placing the speakers on page 18 ! Connecting the speakers on page 19 ! Installing your speaker system on page 19 ! Bi-amping your speakers on page 20
j
4 Connecting the components
! About the audio connection on page 21 ! About the video converter on page 22 ! Connecting your TV and playback components on page 23 ! Connecting AM/FM antennas on page 28 ! Plugging in the receiver on page 32
j
5 Power On
j
6 Changing the OSD display language (OSD Language) (page 34)
j
7 MCACC speaker settings
! Automatically conducting optimum sound tuning (Full Auto MCACC) on page 34
j
8 The Input Setup menu (page 36)
(When using connections other than the recommended connections)
j
9 Basic playback (page 38)
j
10 Adjusting the sound and picture quality as desired
! Using the various listening modes (page 45) ! Better sound using Phase Control (page 48) ! Measuring the all EQ type (SYMMETRY/ALL CH ADJ/FRONT ALIGN) (page 73) ! Changing the channel level while listening (page 82) ! Switching on/off the Acoustic Calibration EQ, Auto Sound Retriever or Dialog Enhancement (page 59) ! Setting the PQLS function (page 57) ! Setting the Audio options (page 59) ! Setting the Video options (page 61)
j
11 Other optional adjustments and settings
! Control with HDMI function (page 55) ! The Advanced MCACC menu (page 72) ! The System Setup and Other Setup menus (page 80)
j
12 Making maximum use of the remote control
! Operating multiple receivers (page 67) ! Setting the remote to control other components (page 67)
6
Before you start
Checking what’s in the box ............................................................................................................8
Installing the receiver ...................................................................................................................... 8
Loading the batteries ...................................................................................................................... 8
Operating range of remote control unit ........................................................................................ 8
About using AVNavigator (included CD-ROM) ............................................................................. 9
7
01
Before you start
Checking what’s in the box
Please check that you’ve received the following supplied accessories:
! Setup microphone (cable: 5 m (16.4 ft.)) ! Remote control unit ! AAA size IEC R03 dry cell batteries (to confirm system operation) x2 ! AM loop antenna ! FM wire antenna ! iPod cable ! Power cord ! CD-ROM ! Quick start guide ! Safety Brochure ! Warranty sheet
Installing the receiver
! When installing this unit, make sure to put it on a level and stable surface. ! Don’t install it on the following places:
on a color TV (the screen may distort) near a cassette deck (or close to a device that gives off a magnetic field). This may interfere with the sound. in direct sunlight in damp or wet areas in extremely hot or cold areas in places where there is vibration or other movement in places that are very dusty in places that have hot fumes or oils (such as a kitchen)
! Do not touch this receiver’s bottom panel while the power is on or just after it is turned off. The bottom panel
becomes hot when the power is on (or right after it is turned off) and could cause burns.
Loading the batteries
The batteries included with the unit are to check initial operations; they may not last over a long period. We rec­ommend using alkaline batteries that have a longer life.
CAUTION
Incorrect use of batteries may result in such hazards as leakage and bursting. Observe the following precautions:
! Never use new and old batteries together. ! Insert the plus and minus sides of the batteries properly according to the marks in the battery case. ! Batteries with the same shape may have different voltages. Do not use different batteries together. ! When disposing of used batteries, please comply with governmental regulations or environmental public insti-
tution’s rules that apply in your country/area.
(Symbol examples for batteries)
These symbols are only valid in the European Union.
Pb
K058c_A1_En
Operating range of remote control unit
The remote control may not work properly if:
! There are obstacles between the remote control and the receiver’s remote sensor. ! Direct sunlight or fluorescent light is shining onto the remote sensor. ! The receiver is located near a device that is emitting infrared rays. ! The receiver is operated simultaneously with another infrared remote control unit.
30°
30°
7 m (23 ft.)
WARNING
! Do not use or store batteries in direct sunlight or other excessively hot place, such as inside a car or near a
heater. This can cause batteries to leak, overheat, explode or catch fire. It can also reduce the life or perfor­mance of batteries.
8
01
Before you start
About using AVNavigator (included CD-ROM)
The included AVNavigator CD-ROM contains Wiring Navi allowing you to easily make the receiver’s connections and initial settings in dialog fashion. High precision initial settings can be completed easily simply by following the instructions on the screen to make the connections and settings. There are also other features enabling easy use of various functions, including an Interactive Manual that oper­ates in association with the receiver, updating of various types of software, and MCACC Application that lets you check the MCACC measurement results on 3D graphs.
Installing AVNavigator
1 Load the included CD-ROM into your computer’s CD drive.
The CD-ROM’s top menu screen appears.
2 Click ‘Install AVNavigator’ from the CD-ROM top menu.
3 Follow the instructions on the screen to install.
When “Finish” is selected, installation is completed.
4 Remove the included CD-ROM from the computer’s CD drive.
Handling the CD-ROM
Operating Environment
! AVNavigator can be used with Microsoft® Windows® XP/Vista/7. ! A browser is at times used for AVNavigator functions. The supported browser is Microsoft Internet Explorer 8
or 9.
Precautions For Use
! This CD-ROM is for use with a personal computer. It cannot be used with a DVD player or music CD player.
Attempting to play this CD-ROM with a DVD player or music CD player can damage speakers or cause impaired hearing due to the large volume.
License
! Please agree to the “Terms of Use” indicated below before using this CD-ROM. Do not use if you are unwilling
to consent to the terms of its use.
Terms of Use
! Copyright to data provided on this CD-ROM belongs to PIONEER CORPORATION. Unauthorized transfer,
duplication, broadcast, public transmission, translation, sales, lending or other such matters that go beyond the scope of “personal use” or “citation” as defined by Copyright Law may be subject to punitive actions. Permission to use this CD-ROM is granted under license by PIONEER CORPORATION.
General Disclaimer
! PIONEER CORPORATION does not guarantee the operation of this CD-ROM with respect to personal com-
puters using any of the applicable OS. In addition, PIONEER CORPORATION is not liable for any damages incurred as a result of use of this CD-ROM and is not responsible for any compensation. The names of private corporations, products and other entities described herein are the registered trademarks or trademarks of their respective firms.
Using AVNavigator
1 Click [AVNavigator 2012.I] on the desktop to launch AVNavigator.
AVNavigator is launched and Wiring Navi starts up. The language selection screen appears. Follow the instruc­tions on the screen to make the connections and automatic settings.
Wiring Navi only starts up automatically the first time AVNavigator is launched.
2 Select and use the desired function.
AVNavigator includes the following functions:
! Wiring Navi – Guides you through connections and initial settings in dialog fashion. High precision initial
settings can be made easily.
! Operation Guide – Describes the receiver’s playback operations and how to use several functions through
videos and illustrations.
! Interactive Manual – Automatically displays the pages explaining the functions that have been operated on
the receiver. It is also possible to operate the receiver from the Interactive Manual.
! Glossary – Displays glossary pages. ! MCACC Appli – Displays Advanced MCACC measurement results vividly on the computer.
There are special operating instructions for MCACC Application. These instructions are included in the
AVNavigator Interactive Manual’s menus. Refer to them when using MCACC Application.
! Software Update – Allows various types of software to be updated. ! Settings – Used to make various AVNavigator settings. ! Detection – Used to detect the receiver.
Note
To use the AVNavigator of another model, first uninstall (delete) this receiver’s AVNavigator, then install the AVNavigator of the other model.
Deleting the AVNavigator
You can use the following method to uninstall (delete) the AVNavigator from your PC.
% Delete from the Control Panel of the PC.
From the Start menu, click “Program” d “PIONEER CORPORATION” d “AVNavigator 2012.I” d “Uninstall AVNavigator 2012.I”.
9
Controls and displays
Remote control ..............................................................................................................................11
Display ............................................................................................................................................ 13
Front panel ..................................................................................................................................... 14
10
02
Controls and displays
Remote control
This section explains how to operate the remote control for the receiver.
2,3
ALL ZONE STBY
1
4
DISCRETE ON
RCU SETUP
BD DVDDVR
CDTV
USB CBL OPTION
SATTUNER
iPod
INPUT
SELECT
5
TV CONTROL
6
7
CH
AUDIO
PARAMETER
TOP MENU
8
HOME MENU
iPod CTRL
5
5
9
FEATURES
PQLS
PHASE
MPX
PRESET TUNE
222
13
SIGNAL SEL
546
DIMMER SLEEP
SPEAKERS
8
79
D.ACCESS
/ CLR
0
AUTO/ALC/
ZONE 2
DIRECT
Z2
BDR
NET
STATUS
VOLUME
INPUT
VOL
PARAMETER
ENTER
AUTO
S.RTRV
BAND
CH LEVEL
CLASS
ENTER
STANDARD
LISTENING MODE
SOURCERECEIVER
HDMI
ADPT
RECEIVER
MUTE
VIDEO
TOOLS
MENU
RETURN
MCACC
PTY
+Favorite
AUDIO
DISP
CH
CH
ADV SURR
10
RECEIVER
11
12
13
14
15
The remote has been conveniently color-coded according to component control using the following system:
! White – Receiver control, TV control ! Blue – Other controls (See pages 40, 41, 42, 43 and 70.)
1 u RECEIVER
This switches between standby and on for this receiver.
2 ALL ZONE STBY DISCRETE ON
Use this button to perform unique operations (page 69).
3 RCU SETUP
Use to input the preset code when making remote control settings and to set the remote control mode (page 67).
4 Input function buttons
Press to select control of other components (page 67). Use INPUT SELECT c/ d to select the input function (page 39).
5 Receiver Control buttons
Press first to access:
! STATUS – Press to check selected receiver settings (page 64). ! PHASE – Press to switch on/off Phase Control (page 48). ! PQLS – Press to select the PQLS setting (page 57). ! AUTO S.RTRV – Press to restore CD quality sound to compressed audio sources (page 59). ! MCACC – Press to switch between MCACC presets (page 47). ! SIGNAL SEL – Use to select an input signal (page 47). ! CH LEVEL – Press repeatedly to select a channel, then use k/l to adjust the level (page 82). ! SPEAKERS – Use to change the speaker terminal (page 63). ! DIMMER – Dims or brightens the display (page 64). ! SLEEP – Use to put the receiver in sleep mode and select the amount of time before sleep (page 64).
6 TV CONTROL buttons
These buttons can be used to perform operations on the TV to which the TV CONTROL INPUT button is assigned. The TV can be operated with these buttons regardless of the input set for the remote control’s operation mode (page 67).
7 Receiver setting buttons
Press first to access:
! AUDIO PARAMETER – Use to access the Audio options (page 59). ! VIDEO PARAMETER – Use to access the Video options (page 61). ! HOME MENU – Use to access the Home Menu (pages 34, 36, 56, 73 and 81). ! RETURN – Press to confirm and exit the current menu screen.
8 i/j/k/l/ENTER
Use the arrow buttons when setting up your surround sound system (see page 73) and the Audio or Video options (page 59 or 61).
9 ZONE 2
Switch to perform operations in ZONE 2 (page 63).
10 LISTENING MODE controls
! AUTO/ALC/DIRECT – Switches between Auto Surround (page 46), Auto Level Control mode and Stream
Direct mode (page 47).
! STANDARD – Press for Standard decoding and to switch various modes (2 Pro Logic, Neo:6, etc.) (page 46). ! ADV SURR – Use to switch between the various surround modes (page 46).
11 Remote control LED
Lights when a command is sent from the remote control.
11
02
12 OPTION
The preset codes of desired devices can be registered in the remote control and button operations can be regis­tered using the learning mode.
13
Switches the remote to control the receiver (used to select the white commands). Switch to perform operations in the main zone. Also use this button to set up surround sound.
14 VOLUME +/–
Use to set the listening volume.
15 MUTE
Mutes the sound or restores the sound if it has been muted (adjusting the volume also restores the sound).
Controls and displays
12
02
Controls and displays
Display
21 3 108654 119 12 13 14
2
AUTO
HDMI
DIGITAL
ANALOG
AUTO SURROUND STREAM DIRECT
2
PROLOGIC x
ADV.SURROUND
SP AB
8
L C R SL SR XL XR
Neo:6
STANDARD
SLEEP
XC
LFE
DIGITAL PLUS
2
TrueHD
DTS HD ES 96/24
CD
MSTR
DSD PCM MULTI-ZONE S.RTRV SOUND UP MIX
TUNER
iPod
1 Signal indicators
Light to indicate the currently selected input signal. AUTO lights when the receiver is set to select the input sig­nal automatically (page 47).
2 Program format indicators
Light to indicate the channels to which digital signals are being input.
! L/R – Left front/Right front channel ! C – Center channel ! SL/SR – Left surround/Right surround channel ! LFE – Low frequency effects channel (the (( )) indicators light when an LFE signal is being input) ! XL/XR – Two channels other than the ones above ! XC – Either one channel other than the ones above, the mono surround channel or matrix encode flag
3 Digital format indicators
Light when a signal encoded in the corresponding format is detected.
! 2 DIGITAL – Lights with Dolby Digital decoding. ! 2 DIGITAL PLUS – Lights with Dolby Digital Plus decoding. ! 2 TrueHD – Lights with Dolby TrueHD decoding. ! DTS – Lights with DTS decoding. ! DTS HD – Lights with DTS-HD decoding. ! 96/24 – Lights with DTS 96/24 decoding. ! DSD PCM – Light during DSD (Direct Stream Digital) to PCM conversion with SACDs. ! PCM – Lights during playback of PCM signals. ! MSTR – Lights during playback of DTS-HD Master Audio signals.
4 MULTI-ZONE
Lights when the MULTI-ZONE feature is active (page 63).
5 SOUND
Lights when the DIALOG E (Dialog Enhancement) or TONE (tone controls) features is selected (page 59).
6 PQLS
Lights when the PQLS feature is active (page 57).
7 S.RTRV
Lights when the Auto Sound Retriever function is active (page 59).
PQLS
DVD
BD
19 2016 17 18
7
ALC
TV
DVR
AT T
OVER
VIDEO
HDMI
TUNED STEREO MONO
[ 2 ]
USB
[ 3 ]
dB
[ 4 ]
8 Listening mode indicators
! AUTO SURROUND – Lights when the Auto Surround feature is switched on (page 46). ! ALC – Lights when the ALC (Auto level control) mode is selected (page 46).
15
! STREAM DIRECT – Lights when Direct/Pure Direct is selected (page 47). ! ADV.SURROUND – Lights when one of the Advanced Surround modes has been selected (page 46). ! STANDARD – Lights when one of the Standard Surround modes is switched on (page 46).
9 (PHASE CONTROL)
Lights when the Phase Control is switched on (page 48).
10 Analog signal indicators
Light to indicate reducing the level of an analog signal (page 59).
11 Tuner indicators
! TUNED – Lights when a broadcast is being received. ! STEREO – Lights when a stereo FM broadcast is being received in auto stereo mode. ! MONO – Lights when the mono mode is set using MPX.
12
Lights when the sound is muted.
13 Master volume level
Shows the overall volume level. “---” indicates the minimum level, and “+12dB” indicates the maximum level.
14 Input function indicators
Light to indicate the input function you have selected.
15 Scroll indicators
Light when there are more selectable items when making the various settings.
16 Speaker indicators
Lights to indicate the current speaker system using SPEAKERS (page 63).
17 SLEEP
Lights when the receiver is in sleep mode (page 64).
18 Matrix decoding format indicators
! 2PRO LOGIC IIx – This lights to indicate 2 Pro Logic II / 2 Pro Logic IIx decoding (page 46). ! Neo:6 – When one of the Neo:6 modes of the receiver is on, this lights to indicate Neo:6 processing (page 46).
19 Character display
Displays various system information.
20 Remote control mode indicator
Lights to indicate the receiver’s remote control mode setting. (Not displayed when set to 1.) (page 85)
13
02
33
Controls and displays
Front panel
1 2 5
ADVANCED
MCACC
SPEAKERS CONTROL – MULTI-ZONE – ON/OFF BAND TUNER EDIT TUNE PRESET ENTER
INPUT SELECTOR
STANDBY/ON
1 u STANDBY/ON
This switches between standby and on for this receiver.
2 INPUT SELECTOR dial
Use to select an input function.
3 Indicators
! ADVANCED MCACC – Lights when EQ is set to ON in the AUDIO PARAMETER menu (page 59). ! FL OFF – Lights when “off” (nothing displayed) is selected with the display’s dimmer adjustment (page 64). ! HDMI – Blinks when connecting an HDMI-equipped component; lights when the component is connected
(page 23).
! iPod iPhone iPad – Lights to indicate iPod/iPhone/iPad is connected (page 31).
4 MULTI-ZONE controls
If you’ve made MULTI-ZONE connections (page 29) use these controls to control the sub zone from the main zone (page 63).
5 Character display
See Display on page 13.
6 TUNER controls
! BAND – Switches between AM and FM radio bands (page 42). ! TUNER EDIT – Use with TUNE i/j, PRESET k/l and ENTER to memorize and name stations for recall
(page 42).
! TUNE i/j – Find radio frequencies (page 42). ! PRESET k/l – Find preset stations (page 43).
7 Remote sensor
Receives the signals from the remote control (page 8).
8 MASTER VOLUME dial
9 SPEAKERS
Use to change the speaker terminal (page 63).
467 8
FL OFF
AUTO SURR/ALC/ STREAM DIRECT
PHONES
109 11 15
SURROUND
SURROUND
iPod
iPhone
MCACC
iPad
SETUP MIC
VIDEO
12 13 14
ADVANCED
STANDARD
iPod iPhone iPad DIRECT
CONTROLSTEREO
USB
HDMI 5 INPUT
iPod iPhone iPadHDMI
PUSH OPEN
MASTER VOLUME
10 PHONES jack
Use to connect headphones. When the headphones are connected, there is no sound output from the speakers.
11 Listening mode buttons
! AUTO SURR/ALC/STREAM DIRECT – Switches between Auto Surround (page 46), Auto Level Control and
Stream Direct mode (page 47).
! STANDARD SURROUND – Press for Standard decoding and to switch various modes (2 Pro Logic, Neo:6,
Stereo etc.) (page 46).
! ADVANCED SURROUND – Use to switch between the various surround modes (page 46). ! STEREO – Press to select stereo playback mode (page 46).
12 MCACC SETUP MIC jack
Use to connect the supplied microphone (page 34).
13 iPod iPhone iPad USB terminals
Use to connect your Apple iPod/iPhone/iPad as an audio and video source (page 31), or connect a USB device for audio and photo playback (page 31).
14 HDMI input connector
Use for connection to a compatible HDMI device (Video camera, etc.) (page 31).
15 iPod iPhone iPad DIRECT CONTROL
Change the receiver’s input to the iPod and enable iPod operations on the iPod (page 40).
Removing the front cover
CONTROL ON / OFF
iPod
iPhone
USB
iPad
Attaching the front cover
2
1
iPod
iPhone
USB
iPad
14
Connecting your equipment
Connecting your equipment .........................................................................................................16
Rear panel ......................................................................................................................................16
Determining the speakers’ application ........................................................................................17
Placing the speakers ...................................................................................................................... 18
Connecting the speakers ...............................................................................................................19
Installing your speaker system ..................................................................................................... 19
Selecting the Speaker system ....................................................................................................... 21
About the audio connection ......................................................................................................... 21
About the video converter ...........................................................................................................22
About HDMI ................................................................................................................................... 22
Connecting your TV and playback components .........................................................................23
Connecting an HDD/DVD recorder, BD recorder and other video sources ............................... 25
Connecting a satellite/cable receiver or other set-top box ........................................................26
Connecting other audio components .......................................................................................... 27
Connecting AM/FM antennas .......................................................................................................28
MULTI-ZONE setup ........................................................................................................................29
Connecting to the network through LAN interface ...................................................................30
Connecting optional Bluetooth ADAPTER ...................................................................................30
Connecting an iPod........................................................................................................................31
Connecting a USB device ..............................................................................................................31
Connecting an HDMI-equipped component to the front panel input ...................................... 31
Connecting to a wireless LAN ....................................................................................................... 31
Connecting an IR receiver .............................................................................................................32
Switching components on and off using the 12 volt trigger ..................................................... 32
Plugging in the receiver ................................................................................................................ 32
15
03
Connecting your equipment
Connecting your equipment
This receiver provides you with many connection possibilities, but it doesn’t have to be difficult. This chapter explains the kinds of components you can connect to make up your home theater system.
CAUTION
! Before making or changing the connections, switch off the power and disconnect the power cord from the
power outlet. Plugging in should be the final step.
! When making connections, also keep the power cords of the devices being connected unplugged from the
power outlets.
! Depending on the device being connected (amplifier, receiver, etc.), the methods of connection and terminal
names may differ from the explanations in this manual. Also refer to the operating instructions of the respec­tive devices.
Rear panel
ASSIGN-
)
LAN
(10/100
HDMI
ASSIGNABLE
IR
OUT
12V TRIGGER
(
OUTPUT 12 V
50 mA MAX
1
2
IN
(
SAT/CBL)(DVR/BDR
DVR/BDR
OUT
DVD IN
IN
R
3
IN
BD IN
)
AUDIO PRE OUT
ZONE 2
L
OUT
R
DVR/BDR
L
R
DVD
SAT/CBL
ANALOG IN
(CD)
ASSIGNABLE
IN
-
1 6
(
)
DVD
VIDEO
MONITOR
OUT
IN
SAT/ CBL
IN
IN
1
)
(
)
DVD
ASSIGNABLE
IN
2
(
DVR/
BDR)
MONITOR OUT
YPBP
COMPONENT VIDEORS-232C
6
IN4IN OUT
SUB WOOFER
1
ADAPTER PORT
2
(
OUTPUT 5 V
0.1 A MAX
ANTENNA
INOUT
IN
A
AM LOOP
L
R
FM UNBAL
1
75
)
OPTICAL COAXIAL
ABLE
DC OUTPUT
for WIRELESS LAN
IN1IN
(
OUTPUT 5 V
(TV)
)
0.6 A MAX
SURROUNDCENTERFRONT
SPEAKERS
(
DVR/BDR
2
ASSIGNABLE
2
IN1IN
)
(
)
(
DVD
SAT/CBL
SURROUND BACK / ZONE 2
)
(
)
Single
FRONT HEIGHT / WIDE /
RLRLRLRL
AC IN
B
Note
! The RS-232C terminal is exclusively for the installer. ! The input functions below are assigned by default to the receiver’s different input terminals. Refer to The Input
Setup menu on page 36 to change the assignments if other connections are used.
Input function
BD
HDMI Audio Component
(BD)
DVD IN 1 COAX-1 IN 1
SAT/CBL IN 2 COAX-2
DVR/BDR IN 3 OPT-2 IN 2
TV OPT-1
HDMI 4 IN 4
HDMI 5
(front panel)
IN 5
HDMI 6 IN 6
CD ANALOG-1
Input Terminals
16
03
Connecting your equipment
Determining the speakers’ application
This unit permits you to build various surround systems, in accordance with the number of speakers you have.
! Be sure to connect speakers to the front left and right channels (L and R). ! It is also possible to only connect one of the surround back speakers (SB) or neither. ! If you have two subwoofers, the second subwoofer can be connected to the SUBWOOFER 2 terminal.
Connecting two subwoofers increases the bass sound to achieve more powerful sound reproduction. In this case, the same sound is output from the two subwoofers.
Choose one from Plans [A] to [E] below.
Important
! The Speaker System setting must be made if you use any of the connections shown below other than [A] (see
Speaker system setting on page 81).
! Sound does not come through simultaneously from the front height, front wide, speaker B and surround back
speakers. Output speakers are different depending on the input signal or listening mode.
[A] 7.2 channel surround system (Front height)
*Default setting
! Speaker System setting: Normal(SB/FH)
FHR
FHL
L
SW 2
SL
R
SW
1
C
SBL
SR
SBR
[B] 7.2 channel surround system (Front wide)
! Speaker System setting: Normal(SB/FW)
R
SW
1
SBL
FWR
SR
SBR
L
C
SW 2
FWL
SL
This plan replaces the left and right front height speakers shown in [A] with the left and right front wide speakers (FWL/FWR). It is not possible to produce sound simultaneously from the front wide speakers and the surround back speakers. This surround system provides a sound field with good association between the sounds of the different channels.
[C] 7.2 channel surround system & Speaker B connection
! Speaker System setting: Speaker B
R
L
SW
SW 1
C
2
SR
R
L
A 7.2 ch surround system connects the left and right front speakers (L/R), the center speaker (C), the left and right front height speakers (FHL/FHR), the left and right surround speakers (SL/SR), the left and right surround back speakers (SBL/SBR), and the subwoofers (SW 1/SW 2). It is not possible to produce sound simultaneously from the front height speakers and the surround back speakers. This surround system produces a more true-to-life sound from above.
SL
SBL
With these connections you can simultaneously enjoy 5.2-channel surround sound in the main zone with stereo playback of the same sound on the B speakers. The same connections also allow for 7.2-channel surround sound in the main zone when not using the B speakers.
SBR
Speaker B
17
03
Connecting your equipment
[D] 5.2 channel surround system & Front Bi-amping connection (High quality surround)
! Speaker System setting: Front Bi-Amp Bi-amping connection of the front speakers for high sound quality with 5.2-channel surround sound.
Front Bi-Amp
R
L
SW
SW 1
C
2
SR
SL
[E] 5.2 channel surround system & ZONE 2 connection (Multi Zone)
! Speaker System setting: ZONE 2 With these connections you can simultaneously enjoy 5.2-channel surround sound in the main zone with stereo playback on another component in ZONE 2. (The selection of input devices is limited.)
Main zone
R
L
SW 1
C
2
SW
SR
SL
ZONE 2
Sub zone
R
L
Other speaker connections
! Your favorite speaker connections can be selected even if you have fewer than 5.2 speakers (except front left/
right speakers).
! When not connecting a subwoofer, connect speakers with low frequency reproduction capabilities to the front
channel. (The subwoofer’s low frequency component is played from the front speakers, so the speakers could be damaged.)
! After connecting, be sure to conduct the Full Auto MCACC (speaker environment setting) procedure. See
Automatically conducting optimum sound tuning (Full Auto MCACC) on page 34.
Placing the speakers
Refer to the chart below for placement of the speakers you intend to connect.
2SW 1
FHL
FWL
SL
! Place the surround speakers at 120º from the center. If you, (1) use the surround back speaker, and, (2) don’t
use the front height speakers / front wide speakers, we recommend placing the surround speaker right beside you.
! If you intend to connect only one surround back speaker, place it directly behind you. ! Place the left and right front height speakers at least one meter (3.3 ft.) directly above the left and right front
speakers.
Some tips for improving sound quality
Where you put your speakers in the room has a big effect on the quality of the sound. The following guidelines should help you to get the best sound from your system. ! The subwoofer can be placed on the floor. Ideally, the other speakers should be at about ear-level when you’re
listening to them. Putting the speakers on the floor (except the subwoofer), or mounting them very high on a wall is not recommended.
! For the best stereo effect, place the front speakers 2 m to 3 m (6 ft. to 9 ft.) apart, at equal distance from the TV. ! If you’re going to place speakers around your CRT TV, use shielded speakers or place the speakers at a suffi-
cient distance from your CRT TV.
! If you’re using a center speaker, place the front speakers at a wider angle. If not, place them at a narrower
angle.
! Place the center speaker above or below the TV so that the sound of the center channel is localized at the TV
screen. Also, make sure the center speaker does not cross the line formed by the leading edge of the front left and right speakers.
! It is best to angle the speakers towards the listening position. The angle depends on the size of the room. Use
less of an angle for bigger rooms.
! Surround and surround back speakers should be positioned 60 cm to 90 cm (2 ft. to 3 ft.) higher than your
ears and tilted slightly downward. Make sure the speakers don’t face each other. For DVD-Audio, the speakers should be more directly behind the listener than for home theater playback.
! Try not to place the surround speakers farther away from the listening position than the front and center speak-
ers. Doing so can weaken the surround sound effect.
SW
C
L
30 30
60
120 120
60
SBL
SB
FHR
R
FWR
60
SR
SBR
18
03
1F
Connecting your equipment
Connecting the speakers
Each speaker connection on the receiver comprises a positive (+) and negative (–) terminal. Make sure to match these up with the terminals on the speakers themselves. This unit supports speakers with a nominal impedance of 6 W to 16 W.
CAUTION
! These speaker terminals carry HAZARDOUS LIVE voltage. To prevent the risk of electric shock when con-
necting or disconnecting the speaker cables, disconnect the power cord before touching any uninsulated parts.
! Make sure that all the bare speaker wire is twisted together and inserted fully into the speaker terminal. If any
of the bare speaker wire touches the back panel it may cause the power to cut off as a safety measure.
Bare wire connections
CAUTION
Make sure that all speakers are securely installed. This not only improves sound quality, but also reduces the risk of damage or injury resulting from speakers being knocked over or falling in the event of external shocks such as earthquakes.
1 Twist exposed wire strands together.
2 Loosen terminal and insert exposed wire.
3 Tighten terminal.
123
10 mm (3/8 in.)
Installing your speaker system
At the very least, front left and right speakers only are necessary. Note that your main surround speakers should always be connected as a pair, but you can connect just one surround back speaker if you like (it must be con­nected to the left surround back terminal).
Standard surround connection
The front height terminals can also be used for the front wide and Speaker B speakers.
Front height setting
Front height right Front height left
Front wide right Front wide left
Speaker B - right Speaker B - left
Front right Center Subwoofer 2Subwoofer
LINE LEVEL
INPUT
PRE OUT
SUB WOOFER
1
2
A
Front wide setting
Speaker B setting
SURROUNDCENTERFRONT
LINE LEVEL
INPUT
SURROUND BACK / ZONE 2
(
Single
FRONT HEIGHT / WIDE /
)
RLRLRLRL
ront left
B
Note
! Please refer to the manual that came with your speakers for details on how to connect the other end of the
speaker cables to your speakers.
! Use an RCA cable to connect the subwoofer. It is not possible to connect using speaker cables. ! If you have two subwoofers, the second subwoofer can be connected to the SUBWOOFER 2 terminal.
Connecting two subwoofers increases the bass sound to achieve more powerful sound reproduction. In this case, the same sound is output from the two subwoofers.
Banana plug connections
If you want to use speaker cables terminated with banana plugs, screw the speaker terminal fully shut, then plug the banana plug into the end of the speaker terminal.
19
PRE OUT
SUB WOOFER
1
2
Surround right
FRONT HEIGHT / WIDE /
SURROUND BACK / ZONE 2
SURROUNDCENTERFRONT
A
B
(
)
Single
RLRLRLRL
SPEAKERS
The surround back terminals can also be used for ZONE 2.
5.2 ch surround setting
Not connected Not connected
Not connected Surround back
Surround back right Surround back left
ZONE 2 - Right ZONE 2 - Left
6.2 ch surround setting
7.2 ch surround setting
ZONE 2 setting
Surround left
03
Connecting your equipment
Bi-amping your speakers
Bi-amping is when you connect the high frequency driver and low frequency driver of your speakers to different amplifiers for better crossover performance. Your speakers must be bi-ampable to do this (having separate termi­nals for high and low) and the sound improvement will depend on the kind of speakers you’re using.
Front right Front left
Bi-amp compatible
SUB WOOFER
1
2
B
speaker
LINE LEVEL
INPUT
Center Subwoofer 2Subwoofer 1
A
SURROUNDCENTERFRONT
High
Low
PRE OUT
PRE OUT
SUB WOOFER
1
2
A
FRONT HEIGHT / WIDE /
SURROUND BACK / ZONE 2
SURROUNDCENTERFRONT
(
)
Single
RLRLRLRL
SPEAKERS
Bi-amp compatible
LINE LEVEL
INPUT
SURROUND BACK / ZONE 2
(
)
Single
speaker
FRONT HEIGHT / WIDE /
RLRLRLRL
High
Low
B
Bi-wiring your speakers
Your speakers can also be bi-wired if they support bi-amping. ! With these connections, the Speaker System setting makes no difference.
CAUTION
! Don’t connect different speakers from the same terminal in this way. ! When bi-wiring as well, heed the cautions for bi-amping shown above.
% To bi-wire a speaker, connect two speaker cords to the speaker terminal on the receiver.
Using a banana plug for the second connection is recommended.
Surround leftSurround right
CAUTION
! Most speakers with both High and Low terminals have two metal plates that connect the High to the Low
terminals. These must be removed when you are bi-amping the speakers or you could severely damage the amplifier. See your speaker manual for more information.
! If your speakers have a removable crossover network, make sure you do not remove it for bi-amping. Doing so
may damage your speakers.
20
03
Connecting your equipment
Selecting the Speaker system
The front height terminals can be used for front wide and Speaker B connections, in addition to for the front height speakers. Also, the surround back terminals can be used for bi-amping and ZONE 2 connections, in addi­tion to for the surround back speakers. Make this setting according to the application.
Front height setup
*Default setting
1 Connect a pair of speakers to the front height speaker terminals.
See Standard surround connection on page 19.
2 If necessary, select ‘Normal(SB/FH)’ from the Speaker System menu.
See Speaker system setting on page 81 to do this.
Front wide setup
1 Connect a pair of speakers to the front height speaker terminals.
See Standard surround connection on page 19.
2 Select ‘Normal(SB/FW)’ from the Speaker System menu.
See Speaker system setting on page 81 to do this.
Speaker B setup
You can listen to stereo playback in another room.
1 Connect a pair of speakers to the front height speaker terminals.
See Standard surround connection on page 19.
2 Select ‘Speaker B’ from the Speaker System menu.
See Speaker system setting on page 81 to do this.
Bi-Amping setup
Bi-amping connection of the front speakers for high sound quality with 5.1-channel surround sound.
1 Connect bi-amp compatible speakers to the front and surround back speaker terminals.
See Bi-amping your speakers on page 20.
2 Select ‘Front Bi-Amp’ from the Speaker System menu.
See Speaker system setting on page 81 to do this.
About the audio connection
Types of cables and terminals
HDMI HD audio
Digital (Coaxial)Conventional digital audio
Digital (Optical)
Sound signal priority
RCA (Analog)
(White/Red)
! With an HDMI cable, video and audio signals can be transferred in high quality over a single cable.
Transferable audio signals
Conventional analog audio
ZONE 2 setup
With these connections you can simultaneously enjoy 5.1-channel surround sound in the main zone with stereo playback on another component in ZONE 2.
1 Connect a pair of speakers to the surround back speaker terminals.
See Standard surround connection on page 19.
2 Select ‘ZONE 2’ from the Speaker System menu.
See Speaker system setting on page 81 to do this.
21
03
Connecting your equipment
About the video converter
The video converter ensures that all video sources are output through the HDMI OUT terminal. If the TV is only connected to the receiver’s composite VIDEO MONITOR OUT jacks, all the other video devices must be connected through composite connections. If several video components are assigned to the same input function (see The Input Setup menu on page 36), the converter gives priority to HDMI, component, then composite (in that order).
Terminal for connection with source device
HDMI IN HDMI OUT
YPBP
COMPONENT
High picture quality
Note
! The only exception is HDMI: since this resolution cannot be downsampled, you must connect your monitor/TV
to the receiver’s HDMI output when connecting this video source.
! If the video signal does not appear on your TV, try adjusting the resolution settings on your component or dis-
play. Note that some components (such as video game units) have resolutions that may not be converted. In this case, try switching Digital Video Conversion (in Setting the Video options on page 61) OFF.
! The signal input resolutions that can be converted from the component video input for the HDMI output are
480i/576i, 480p/576p, 720p and 1080i. 1080p signals cannot be converted.
This item incorporates copy protection technology that is protected by U.S. patents and other intellectual property rights of Rovi Corporation. Reverse engineering and disassembly are prohibited.
R
VIDEO IN
VIDEO IN
Terminal for connection with TV monitor
YPBP
COMPONENT VIDEO
MONITOR OUT
MONITOR OUT
R
VIDEO
Video signals can be output
About HDMI
The HDMI connection transfers uncompressed digital video, as well as almost every kind of digital audio. This receiver incorporates High-Definition Multimedia Interface (HDMI®) technology. This receiver supports the functions described below through HDMI connections.
! Digital transfer of uncompressed video (contents protected by HDCP (1080p/24, 1080p/60, etc.)) ! 3D signal transfer ! Deep Color signal transfer ! x.v.Color signal transfer ! ARC (Audio Return Channel) ! Input of multi-channel linear PCM digital audio signals (192 kHz or less) for up to 8 channels ! Input of the following digital audio formats:
Dolby Digital, Dolby Digital Plus, DTS, High bitrate audio (Dolby TrueHD, DTS-HD Master Audio, DTS-HD
High Resolution Audio), DVD-Audio, CD, SACD (DSD signal), Video CD, Super VCD
! Synchronized operation with components using the Control with HDMI function (see Control with HDMI func-
tion on page 55)
Note
! An HDMI connection can only be made with DVI-equipped components compatible with both DVI and High
Bandwidth Digital Content Protection (HDCP). If you choose to connect to a DVI connector, you will need a separate adaptor (DVIdHDMI) to do so. A DVI connection, however, does not support audio signals. Consult your local audio dealer for more information.
! If you connect a component that is not compatible with HDCP, an HDCP ERROR message is displayed on
the front panel display. Some components that are compatible with HDCP still cause this message to be dis­played, but so long as there is no problem with displaying video this is not a malfunction.
! Depending on the component you have connected, using a DVI connection may result in unreliable signal
transfers.
! This receiver supports SACD, Dolby Digital Plus, Dolby TrueHD and DTS-HD Master Audio. To take advantage
of these formats, however, make sure that the component connected to this receiver also supports the corre­sponding format.
! Use a High Speed HDMI® cable. If an HDMI cable other than a High Speed HDMI® cable is used, it may not
work properly.
! When an HDMI cable with a built-in equalizer is connected, it may not operate properly. ! Signal transfer is only possible when connected to a compatible component. ! HDMI format digital audio transmissions require a longer time to be recognized. Due to this, interruption in the
audio may occur when switching between audio formats or beginning playback.
! Turning on/off the device connected to this unit’s HDMI OUT terminal during playback, or disconnecting/con-
necting the HDMI cable during playback, may cause noise or interrupted audio.
HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
“x.v.Color” and are trademarks of Sony Corporation.
22
03
Connecting your equipment
Connecting your TV and playback components
Connecting using HDMI
If you have an HDMI or DVI (with HDCP) equipped component (Blu-ray Disc player (BD), etc.), you can connect it to this receiver using a commercially available HDMI cable. If the TV and playback components support the Control with HDMI feature, the convenient Control with HDMI functions can be used (see Control with HDMI function on page 55).
This connection is required in
order to listen to the sound of HDMI/DVI-compatible Blu-ray Disc player
1
IN
HDMI
ASSIGNABLE
-
1 6
(
)
(
DVD
Other HDMI/DVI­equipped component
2
IN
SAT/CBL)(DVR/BDR
3
IN
HDMI INHDMI OUT HDMI OUT
AUDIO OUT
RL
ANALOG
4
IN
BD IN
)
6
IN OUT
the TV over the receiver.
HDMI/DVI-compatible monitor
Select one
DIGITAL OUT
COAXIALOPTICAL
ASSIGN-
OPTICAL COAXIAL
ABLE
2
IN1IN
(TV)
(
DVR/BDR
)
(
IN1IN
DVD
)
(
SAT/CBL
ASSIGNABLE
2
)
! For input components, connections other than HDMI connections are also possible (see Connecting your DVD
player with no HDMI output on page 24).
! If you want to listen to the sound of the TV over the receiver, connect the receiver and TV with audio cables.
When the TV and receiver are connected by HDMI connections, if the TV supports the HDMI ARC (Audio
Return Channel) function, the sound of the TV can be input to the receiver via the HDMI OUT terminal, so there is no need to connect an audio cable. In this case, set ARC at HDMI Setup to ON (see HDMI Setup on
page 56).
If you use a coaxial digital audio cable or RCA (analog) audio cable, you’ll need to tell the receiver which digi-
tal or analog audio input you connected the TV to (see The Input Setup menu on page 36).
ASSIGN-
)
LAN
(10/100
1IN2
IN
IN BD IN3IN4IN OUT
HDMI
ASSIGNABLE
-
1 6
(
)
(
)
DVD
SAT/CBL)(DVR/BDR
OPTICALCOAXIAL
6
ABLE
ASSIGNABLE
DC OUTPUT
for WIRELESS LAN
2
2
IN1IN
IN1IN
(
OUTPUT 5 V
(TV)
(
)
(
)
(
)
)
DVR/BDR
DVD
SAT/CBL
0.6 A MAX
L
IN
R
1
ANALOG IN
(CD)
ASSIGNABLE
IN
ANALOG IN
(CD)
ASSIGNABLE
L
R
1
23
03
RL
RL
Connecting your equipment
Connecting your DVD player with no HDMI output
This diagram shows connections of a TV (with HDMI input) and DVD player (or other playback component with no HDMI output) to the receiver.
HDMI/DVI-compatible monitor
DVD player, etc.
Select one
DIGITAL OUT
COAXIALOPTICAL
ASSIGN­ABLE
2
IN1IN
(TV)
(
)
DVR/BDR
IN1IN
(
)
DVD
ASSIGNABLE
2
(
SAT/CBL
AUDIO OUT
ANALOG
)
HDMI
ASSIGNABLE
-
1 6
HDMI IN
1
IN
(
DVD
2
IN
)
(
SAT/CBL)(DVR/BDR
DVD IN
Select one
VIDEO OUT
VIDEO
3
IN
BD IN
4
IN
)
COMPONENT VIDEO OUT
6
IN OUT
PR
PB
Y
OPTICALCOA XIAL
Connecting your TV with no HDMI input
This diagram shows connections of a TV (with no HDMI input) and DVD player (or other playback component) to the receiver.
Important
! With these connections, the picture is not output to the TV even if the DVD player is connected with an HDMI
cable. Connect the receiver and TV using the same type of video cable as used to connect the receiver and player.
! Also, when the receiver and TV are connected by anything other than an HDMI cable, the OSD function allow-
ing display of the receiver’s settings, operations, etc., on the TV’s screen cannot be used. In this case, watch the receiver’s front panel display while performing the various operations and making settings.
DVD player, etc.
TV
COMPONENT VIDEO IN
PR
PB
Y
VIDEO IN
VIDEO
COMPONENT VIDEO OUT
PR
PB
Y
VIDEO OUT
VIDEO
HDMI OUT
Select oneSelect oneSelect one
DIGITAL OUT
COAXIALOPTICAL
AUDIO OUT
ANALOG
IN
1
(
)
DVD
ASSIGNABLE
YPBP
COMPONENT VIDEO
R
DVD
1
2
IN
IN
IN BD IN3IN4IN OUT
HDMI
ASSIGNABLE
-
1 6
(
)
(
)
DVD
SAT/CBL)(DVR/BDR
DVD IN
IN
1
(
)
DVD
ASSIGNABLE
YPBP
R
COMPONENT VIDEO
DVD
ASSIGN-
)
LAN
(10/100
OPTICAL COAXIAL
6
ABLE
ASSIGNABLE
DC OUTPUT
for WIRELESS LAN
2
2
IN1IN
IN1IN
(
OUTPUT 5 V
(TV)
(
)
(
)
(
)
)
DVR/BDR
DVD
SAT/CBL
0.6 A MAX
! If you want to listen to the sound of the TV over the receiver, connect the receiver and TV with audio cables
(page 23).
When the TV and receiver are connected by HDMI connections, if the TV supports the HDMI ARC (Audio
Return Channel) function, the sound of the TV can be input to the receiver via the HDMI OUT terminal, so there is no need to connect an audio cable. In this case, set ARC at HDMI Setup to ON (see HDMI Setup on
page 56).
! If you use an optical digital audio cable, you’ll need to tell the receiver which digital input you connected the
player to (see The Input Setup menu on page 36).
24
HDMI
ASSIGNABLE
-
1 6
1
IN
(
DVD
2
IN
)
(
SAT/CBL)(DVR/BDR
VIDEO
MONITOR
OUT
IN
1
(
)
DVD
ASSIGNABLE
IN
2
(
DVR/ BDR)
MONITOR OUT
YPBP
COMPONENT VIDEO
DVD IN
ASSIGN-
3
IN
BD IN
IN
4
6
IN OUT
)
HDMI
ASSIGNABLE
-
1 6
DVD
R
OPTICAL COAXIAL
1IN2
)
OUT
)
YPBP
( SAT/CBL)(DVR/BDR
DVD IN
R
IN BD IN3IN4IN OUT
)
DVD
6
IN
( DVD
VIDEO
MONITOR
IN
1
( DVD
ASSIGNABLE
IN
2
( DVR/ BDR)
MONITOR OUT
COMPONENT VIDEO
IN1IN
(TV)
)
LAN
(10/100
OPTICAL COAXIAL
DC OUTPUT
for WIRELESS LAN
(
OUTPUT 5 V
)
0.6 A MAX
ABLE
(
DVR/BDR
ASSIGN­ABLE
2
IN1IN
(TV)
(
DVR/BDR
ASSIGNABLE
2
ASSIGNABLE
2
IN1IN
)
(
)
(
)
DVD
SAT/CBL
)
(
IN1IN
)
DVD
(
SAT/CBL
2
)
03
Connecting your equipment
! In order to listening to HD audio with this receiver, connect an HDMI cable, and use analog video cable for
video signal input.
Depending on the player, it may not be possible to output video signals to both HDMI and other video output
(composite, etc.) simultaneously, and it may be necessary to make video output settings. Please refer to the operating instructions supplied with your player for more information.
! If you want to listen to the sound of the TV over the receiver, connect the receiver and TV with audio cables
(page 23).
! If you use an optical digital audio cable, you’ll need to tell the receiver which digital input you connected the
player to (see The Input Setup menu on page 36).
Connecting an HDD/DVD recorder, BD recorder and other video sources
This receiver has audio/video inputs suitable for connecting analog or digital video devices, including HDD/DVD recorders and BD recorders. When you set up the receiver you’ll need to tell the receiver which input you connected the recorder to (see also
The Input Setup menu on page 36).
HDD/DVD recorder, BD recorder, etc.
Select one
AUDIO OUT
RL
ANALOG
OPTICALCOA XIAL
DIGITAL OUT
COAXIALOPTICAL
ASSIGN­ABLE
IN1IN
(TV)
(
DVR/BDR
2
)
(
IN1IN
)
DVD
ASSIGNABLE
2
(
SAT/CBL
)
HDMI
ASSIGNABLE
-
1 6
AUDIO IN
RL
ANALOG
1
IN
)
(
SAT/CBL)(DVR/BDR
DVR/BDR
OUT
2
(
IN
DVD
VIDEO IN
VIDEO
3
IN
VIDEO OUT
VIDEO
4
IN
BD IN
)
6
IN OUT
IN
DVR/BDR
L
OUT
R
ASSIGN-
)
LAN
(10/100
1IN2
IN
IN BD IN3IN4IN OUT
HDMI
ASSIGNABLE
-
1 6
(
)
(
)
DVD
SAT/CBL)(DVR/BDR
DVR/BDR
OUT
IN
DVR/BDR
L
OUT
R
OPTICAL COAXIAL
6
ABLE
ASSIGNABLE
DC OUTPUT
for WIRELESS LAN
2
2
IN1IN
IN1IN
(
OUTPUT 5 V
(TV)
(
)
(
)
(
)
)
DVR/BDR
DVD
SAT/CBL
0.6 A MAX
L
IN
R
L
IN
R
! In order to record, you must connect the analog audio cables (the digital connection is for playback only) (page
64).
25
03
Connecting your equipment
! If your HDD/DVD recorder, BD recorder, etc., is equipped with an HDMI output terminal, we recommend con-
necting it to the receiver’s HDMI DVR/BDR IN terminal. When doing so, also connect the receiver and TV by HDMI (see Connecting using HDMI on page 23).
HDMI/DVI-compatible monitor
HDMI IN
HDMI
ASSIGNABLE
-
1 6
(
IN
DVD
HDMI OUT
1
)
HDD/DVD recorder, BD recorder, etc.
2
) (
3
IN
DVR/BDR
BD IN
)
IN
(
SAT/CBL
IN
4
6
IN OUT
Connecting a satellite/cable receiver or other set-top box
Satellite and cable receivers, and terrestrial digital TV tuners are all examples of so-called ‘set-top boxes’. When you set up the receiver you’ll need to tell the receiver which input you connected the set-top box to (see The
Input Setup menu on page 36).
STB
Select one
AUDIO OUT
RL
ANALOG
OPTICAL COAXIAL
DIGITAL OUT
COAXIALOPTICAL
ASSIGN­ABLE
IN1IN
(TV)
(
DVR/BDR
2
IN1IN
)
(
DVD
)
(
SAT/CBL
ASSIGNABLE
2
)
1IN2
IN
HDMI
ASSIGNABLE
-
1 6
(
)
DVD
VIDEO
SAT/ CBL IN
HDMI
ASSIGNABLE
IN BD IN3IN4IN OUT
(
)
SAT/CBL)(DVR/BDR
SAT/CBL
-
1 6
6
IN
(
DVD
VIDEO
SAT/ CBL
IN
1
)
ASSIGN-
)
(10/100
LAN
OPTICALCOAXIAL
ABLE
ASSIGNABLE
DC OUTPUT
for WIRELESS LAN
2
2
IN1IN
IN1IN
(
OUTPUT 5 V
(TV)
(
)
(
)
(
)
DVR/BDR
DVD
SAT/CBL
0.6 A MAX
2
IN
(
SAT/CBL)(DVR/BDR
VIDEO OUT
VIDEO
)
3
IN
BD IN
)
IN
4
6
IN OUT
26
SAT/CBL
03
Connecting your equipment
! If your set-top box is equipped with an HDMI output terminal, we recommend connecting it to the receiver’s
HDMI SAT/CBL IN terminal. When doing so, also connect the receiver and TV by HDMI (see Connecting using
HDMI on page 23).
HDMI OUT
HDMI
ASSIGNABLE
-
1 6
(
IN
DVD
STB
1
2
) (
3
IN
DVR/BDR
BD IN
)
IN
)
(
SAT/CBL
IN
4
6
IN OUT
HDMI/DVI-compatible monitor
HDMI IN
! Even if your set-top box is equipped with an HDMI output terminal, in some cases the sound is output from
the digital audio output (optical or coaxial) and only the video is output from the HDMI output terminal. In this case, make the HDMI and digital audio connections as shown below.
HDMI OUT
STB
DIGITAL OUT
COAXIALOPTICAL
Connecting other audio components
This receiver has both digital and analog inputs, allowing you to connect audio components for playback. When you set up the receiver you’ll need to tell the receiver which input you connected the component to (see also The Input Setup menu on page 36).
CD player, etc.
Select one
DIGITAL OUT
COAXIALOPTICAL
ASSIGN-
OPTICALCOA XIAL
ABLE
2
IN1IN
(TV)
(
DVR/BDR
IN1IN
)
(
DVD
)
ASSIGNABLE
2
(
SAT/CBL
)
HDMI
ASSIGNABLE
-
1 6
1
IN
(
)
DVD
2
IN
IN
(
SAT/CBL)(DVR/BDR
AUDIO OUT
RL
ANALOG
3
BD IN
)
IN
4
6
IN OUT
1
HDMI
ASSIGNABLE
-
1 6
(
IN
DVD
2
IN
)
(
SAT/CBL
HDMI/DVI-compatible monitor
) (
3
IN
DVR/BDR
)
HDMI IN
BD IN
IN
4
6
IN OUT
ASSIGN-
OPTICAL COAXIAL
ABLE
2
IN1IN
(TV)
(
DVR/BDR
)
(
IN1IN
)
DVD
ASSIGNABLE
2
(
SAT/CBL
ASSIGN-
)
LAN
(10/100
1IN2
IN
IN BD IN3IN4IN OUT
HDMI
)
ASSIGNABLE
-
1 6
(
)
(
)
DVD
SAT/CBL)(DVR/BDR
OPTICALCOAXIAL
6
ABLE
ASSIGNABLE
DC OUTPUT
for WIRELESS LAN
2
2
IN1IN
IN1IN
(
OUTPUT 5 V
(TV)
(
)
(
)
(
)
)
DVR/BDR
DVD
SAT/CBL
0.6 A MAX
L
IN
R
1
ANALOG IN (CD)
ASSIGNABLE
IN
ANALOG IN
(CD)
ASSIGNABLE
L
R
1
! If your turntable has line-level outputs (i.e., it has a built-in phono pre-amp), connect it to the ANALOG IN 1
(CD) inputs instead.
27
03
Connecting your equipment
Connecting AM/FM antennas
Connect the AM loop antenna and the FM wire antenna as shown below. To improve reception and sound quality, connect external antennas (see Connecting external antennas on page 28).
ab c
ANTENNA
AM LOOP
5
FM UNBAL 75
1 Pull off the protective shields of both AM antenna wires.
2 Push open the tabs, then insert one wire fully into each terminal, then release the tabs to secure the AM antenna wires.
3 Fix the AM loop antenna to the attached stand.
To fix the stand to the antenna, bend in the direction indicated by the arrow (fig. a) then clip the loop onto the stand (fig. b).
! If you plan to mount the AM antenna to a wall or other surface, secure the stand with screws (fig. c) before
clipping the loop to the stand. Make sure the reception is clear.
4 Place the AM antenna on a flat surface and in a direction giving the best reception.
5 Connect the FM wire antenna into the FM antenna socket.
For best results, extend the FM antenna fully and fix to a wall or door frame. Don’t drape loosely or leave coiled up.
1
4
3
2
Connecting external antennas
To improve FM reception, connect an external FM antenna to FM UNBAL 75 W.
ANTENNA
AM LOOP
75 Ω coaxial cable
FM UNBAL 75
To improve AM reception, connect a 5 m to 6 m (16 ft. to 20 ft.) length of vinyl-coated wire to the AM LOOP termi­nals without disconnecting the supplied AM loop antenna. For the best possible reception, suspend horizontally outdoors.
ANTENNA
Indoor antenna (vinyl-coated wire)
Outdoor antenna
5 m to 6 m (16 ft. to 20 ft.)
AM LOOP
FM UNBAL 75
28
03
Connecting your equipment
MULTI-ZONE setup
This receiver can power up to two independent systems in separate rooms after you have made the proper MULTI­ZONE connections. Different sources can be playing in two zones at the same time or, depending on your needs, the same source can also be used. The main and sub zone have independent power (the main zone power can be off while sub zone is on) and the sub zone can be controlled by the remote or front panel controls.
Making MULTI-ZONE connections
It is possible to make these connections if you have the speakers for the sub zone (ZONE 2). You will also need a separate amplifier if you are not using the speaker terminals for the sub zone (For detail, see MULTI-ZONE setup
using speaker terminals (ZONE 2) on page 29).
MULTI-ZONE listening options
The following table shows the signals that can be output to ZONE 2:
Sub Zone Input functions available
ZONE 2
! It is not possible to down-convert the audio input signal from the HDMI input terminals or digital input terminals (OPTICAL and
COAXIAL) and output them to ZONE 2.
! When any of the INTERNET RADIO, SiriusXM, PANDORA, MEDIA SERVER, FAVORITES, iPod/USB or ADAPTER PORT inputs
is selected in the main zone, it is only possible to select the same input as in the main zone for the sub zone. (Inputs other than the ones listed here can be selected.)
Basic MULTI-ZONE setup (ZONE 2)
% Connect a separate amplifier to the AUDIO ZONE 2 OUT jacks on this receiver.
You should have a pair of speakers attached to the sub zone amplifier as shown in the following illustration.
Sub zone (ZONE 2) Main zone
DVD, SAT/CBL, DVR/BDR, INTERNET RADIO, SiriusXM, PANDORA, MEDIA SERVER, FAVORITES, iPod/USB, TV, CD, TUNER, ADAPTER PORT
(Outputs analog audio)
MULTI-ZONE setup using speaker terminals (ZONE 2)
You must select ZONE 2 in Speaker system setting (page 81) to use this setup.
% Connect a pair of speakers to the surround back speaker terminals.
You should have a pair of speakers attached to the surround back speaker terminals as shown below.
Sub zone (ZONE 2) Main zone
A
RL
SURROUNDCENTERFRONT
SPEAKERS
SURROUND BACK / ZONE 2
(
Single
A
FRONT HEIGHT / WIDE /
)
RLRLRLRL
SURROUND BACK / ZONE 2
SURROUNDCENTERFRONT
SPEAKERS
B
FRONT HEIGHT / WIDE /
B
(
)
Single
RLRLRLRL
AUDIO IN
RL
AUDIO
ZONE 2
L
OUT
R
AUDIO
ZONE 2
L
OUT
R
29
03
Connecting your equipment
Connecting to the network through LAN interface
By connecting this receiver to the network via the LAN terminal, you can listen to Internet radio stations. To listen to Internet radio stations, you must sign a contract with an ISP (Internet Service Provider) beforehand. When connected in this way, you can play audio files stored on the components on the local network, including your computer.
)
LAN
(10/100
)
LAN
(10/100
NAS
Connect the LAN terminal on this receiver to the LAN terminal on your router (with or without the built-in DHCP server function) with a straight LAN cable (CAT 5 or higher). Turn on the DHCP server function of your router. In case your router does not have the built-in DHCP server func­tion, it is necessary to set up the network manually. For details, see Network Setup menu on page 83.
LAN terminal specifications
! LAN terminal : Ethernet jack (10BASE-T/100BASE-TX)
to LAN port
PC
to LAN port
Internet
Modem
LAN
321
LAN cable (sold separately)
WAN
Router
Connecting optional Bluetooth ADAPTER
When the Bluetooth® ADAPTER (AS-BT100 or AS-BT200) is connected to this receiver, a product equipped with Bluetooth wireless technology (portable cell phone, digital music player, etc.) can be used to listen to music
wirelessly.
! The Bluetooth wireless technology enabled device must support A2DP profiles. ! Pioneer does not guarantee proper connection and operation of this unit with all Bluetooth wireless technology
enabled devices.
! The Air Jam function cannot be used with the AS-BT100.
ADAPTER PORT
(
OUTPUT 5 V
)
0.1 A MAX
ADAPTER PORT
(
OUTPUT 5 V
)
0.1 A MAX
Bluetooth® ADAPTER
Important
! Do not move the receiver with the Bluetooth ADAPTER connected. Doing so could cause damage or faulty
contact.
% Switch the receiver into standby and connect Bluetooth ADAPTER to the ADAPTER PORT.
! For instructions on playing the Bluetooth wireless technology device, see Pairing the Bluetooth ADAPTER and
Bluetooth wireless technology device on page 43.
Note
! Refer to the operation manual of the equipment you have as the connected equipment and connection method
may differ depending on your Internet environment.
! When using a broadband Internet connection, a contract with an Internet service provider is required. For
more details, contact your nearest Internet service provider.
30
Loading...
+ 79 hidden pages